2 2 2 HARTREY AVE.. EVANSTON. IL. 6 0 2 0 4 U.S.A.

AREA CODE 3 1 2 / 8 6 6 . 2 2 0 0
TWX: 9 1 0 - 2 3 1 . 0 0 4 8
. CABLE: SHUREMICRO
TELEX: 7 2 - 4 3 8 1 1 SHEET
DATA
MODELS 580SA
and 580SB UNIDYNEB A
I
UNIDIRECTIONAL DYNAMIC MICROPHONES
Frequency Response
50 to 13,000 Hz (see Figure 1)
+20

-
m

-
Y
+I0

g
L
O

5 -I0
L
Y

-20
20 Y) 100 lUm0 10.000 20.003
FREWENCY IN HERTZ

GENERAL TYPICAL FREQUENCY RESPONSE

The Model 580 Series UNIDYNEB A Microphones are FIGURE 1
moving coil dynamic units built to provide wide range
reproduction of music and voice and featuring an ex- Polar Pattern
cellent unidirectional microphone pickup pattern. These Cardioid (unidirectional)-uniform with frequency,
unidirectional microphones are ideal for quality public symmetrical about axis (see Figure 2)
address, theater-stage sound systems, recording, and
other sound reinforcement applications.
Microphone Features:
rn Exceptional true cardioid pickup pattern: sym-
metrical about axis and uniform at all frequen-
cies-providing highly effective suppression of
feedback
rn Uniform shaped response, particularly suitable
for the professional entertainer
rn A built-in On-Off switch with provisions for lock-
ing switch in its On position
rn Versatility-for use in the hand or on a stand-
for use indoors or outdoors FIGURE 2
rn Dependability under all operating conditions
Impedance
The Model 580 Microphones are supplied with an Model 580SA: Microphone impedance is "High" for
adjustable swivel adapter which permits the micro- connection to high-impedance microphone inputs.
phone to be tilted through 90" from vertical to hori- Model 580SB: Microphone rating impedance is 150
zontal. This swivel also allows for "quick-disengage" ohms (160 ohms actual) for connection to micro-
for use as a hand microphone. phone inputs rated at 19 to 300 ohms.
Model 580SA is high impedance for connection to
high-impedance microphone inputs. Output Level (at 1,000 Hz)
580SA 580SB
Model 580SB is low impedance for connection to
microphone inputs rated at 19 to 300 ohms. The low- Open Circuit Voltage* . . . . . -57.5 dB -80.0 dB
impedance microphone is recommended where long (1.33 mV) (.I00 mV)
cable lengths are required or under conditions of se- Power Level * * . . . . . . . . . . . . -58.0 dB
vere hum disturbance. The permissible cable length is *O dB = 1 volt per microbar
practically unlimited since neither response nor level * * O dB = 1 milliwatt per 10 microbars
is appreciably affected by long cables. Shure Model
A95 Series Line Matching Transformers are available Switch
for use in those cases where a low-impedance micro- Built-in On-Off switch with lockplate. To lock switch
phone line is desirable but the associated amplifier in On position, remove screw on lockplate and turn
has a high-impedance input. These transiormers pro- lockplate 180". Reassemble and tighten screw.
vide a proper impedance match between a 19 to 300 Cartridge Shock Mount
ohm microphone line and a high-impedance input and Internal rubber vibration-isolator
are available with various input and output connectors.
Cable
Model 580SA: 4.6m (15 ft), nondetachable, single-
SPECIFICATIONS conductor shielded
TYpe Model 580SB: 4.6m (15 ft), nondetachable, two-
Dynamic conductor shielded
Copyright 1979, Shure Brothers Inc U.S. Patents 3,132,713 and 3,240,883
27A325 (SK) Printed in U.S.A.
Swivel Adapter FURNISHED ACCESSORY
Positive action, adjustable through 90" from vertical Swivel Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . ..A25B
to horizontal, permits easy removal for handheld use,
suitable for mounting on stand with %"-27 thread OPTIONAL ACCESSORIES
Case Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A6lWS
Chrome-plated die casting and ARMO-DUR@ with Line Matching Transformer . . . . . . . . . . . . ..A95 Series
stainless steel grille Desk Stand . . . . . . . . ..S33B, S37A, S38B, S39A, S40A
Quick Disconnect Adapter . . . . . . . . . . . . . . . . . . . . . A45
Dimensions Dual Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..A26M
See Figure 3
REPLACEMENT PARTS
169 rnrn
7(6- 21/32 IN1 1 580SA 580SB
Cartridge . . . . . . . . . . . . . . . . . . . . . R58 R58
Screen and Grille Assembly . . . . . RK51G RK51G
On-Off Switch . . . . . . . . . . . . . . . . . RK48S RK48S

ARCHITECTS' SPECIFICATIONS
OVERALL DIMENSIONS
The microphone shall be a moving coil (dynamic)
FIGURE 3 type with a frequency response of 50 to 13,000 Hz. The
unit shall have a cardioid polar characteristic. The
Net Weight cancellation at the sides shall be approximately 6 dB,
and the cancellation at the rear shall be 15 to 20 dB.
624 grams (1 Ib, 6 oz)
Model 580SA shall be high impedance for connec-
Packaged Weight tion to high-impedance microphone inputs.
907 grams (2 Ib)
Model 580SB shall be low impedance with a rated
impedance of 150 ohms for connection to microphone
PHASING inputs rated at 19 to 300 ohms.
To test two microphones for proper phasing, con- The microphone output shall be:
nect them to an amplifier and talk or sing into them
while holding them three or four inches apart. The Model 580SA . . . . . . . . . . . . . . . . . . . -57.5 dB
sound from the speakers should be the same when (0 dB = 1 volt per microbar)
talking into either microphone or directly between them Model 580SB . . . . . . . . . . . . . . . . . . .-58.0 dB
if they are in phase with each other. If the sound drops (0 dB = 1 milliwatt per 10 microbars)
drastically, or if a dead spot is found when talking
between the two microphones, the microphones are The microphone shall be equipped with a built-in
out of phase. All microphones should be tested in this On-Off switch and a nondetachable 4.6m (15 ft) cable.
manner to insure that they are in phase with each other. The cable for Model 580SA shall be single-conductor
shielded; the cable for Model 580SB shall be two-
To change the phase of a low-impedance micro- conductor shielded.
phone at the equipment end of the cable, interchange
the BLACK and WHITE cable leads where they are The microphone shall be provided with a swivel
connected to the sound system. To change the phase adapter, adjustable through 90" from vertical to hori-
of a microphone, the microphone cartridge leads must zontal, and suitable for mounting on a stand having
be interchanged (see Figure 4). This should be per- a %"-27 thread.
formed by your dealer, the Shure Factory Service De-
partment, or other qualified service personnel. The overall dimensions of the microphone shall be
169 mm (6-21132 in.) in length and 46 mm (1-13116 in.)
CARTRIDGE in diameter.
The microphone shall be the Shure Model 580SA,
580SB, or equivalent.

GUARANTEE
- L ~
TERMINAL ~ ~ ~
FC ASE ~ This Shure product is guaranteed in normal use to
POSITIVE PRESSURE PRODUCES POSITIVE VOLTAGE
be free from electrical and mechanical defects for a
ON CABLE SHIELD period of one year from date of purchase. Please
MODEL 580SA INTERNAL CONNECTIONS retain proof of purchase date. This guarantee includes
all parts and labor. This guarantee is in lieu of any
and all other guarantees or warranties, express or
jSWITCH SHOWN IN
"0FFWPOSITION implied, and there shall be no recovery for any con-
sequential or incidental damages.
SHIELD
,-----
WHITE ! ': SHIPPING INSTRUCTIONS
I .!I
-1

BLACK I / Carefully repack the unit and return it prepaid to:

LY Shure Brothers Incorporated
Attention: Service Department
CARTRIDGE +ASE 1501 West Shure Drive
POSITIVE PRESSURE PRODUCES POSITIVE VOLTAGE Arlington Heights, Illinois 60004
ON BLACK CABLE LEAD
If outside the United States, return the unit to your
MODEL 580SB INTERNAL CONNECTIONS dealer or Authorized Shure Service Center for repair.
FIGURE 4 The unit will be returned to you prepaid.