Quick Start Guide

DM10
Version: 1.1

Due to regular upgrades of systems and products, ZKTeco could not guarantee
exact consistency betweenthe actual product and the written information in this manual.
1
Appearance & Installation
1.
Appearance

Auxiliary input Wiegand reader Status of indicator

Normal communication: The indicator
EXT
RS485 Wiegand reader
flashes every two seconds.
Abnormal communication: The indicator
will glow constantly.
The indicator flashes rapidly within 30s
after the device is connected to the power
supply.
GLED

GLED
BEEP

BEEP
485A
485B

GND
GND

WD1
WD0
GND

WD1
WD0
GND
AUX

12V

12V

RS485 AUX IN READER 1 READER 2

Address





Switch
Setting






Address





Switch
Setting

PWR

1 1 2 3 4 6 1 2 3 4

AUX OUT LOCK VOUT POWER

12VOUT

2 7
COM

COM
GND

GND

GND
SEN
BUT

12V
NO

NO
NC

NC

RS485 ADD. 1 2 1 2
3 4 3 4

Indicator LED
3 1 2 3 4 8 1 2 3 4

4 1 2 3 4 9 1 2 3 4

Auxiliary 12V
output 5 1 2 3 4 10 1 2 3 4

output

DIP
switch Lock Power

2
2.
Installation
1)
Drill holes on the wall 2)
Fix the device with four screws

GLED

GLED
BEEP

BEEP
485A
485B

GND
GND

WD1
WD0
GND

WD1
WD0
GND
AUX

12V

12V
RS485 AUX IN READER 1 READER 2

PWR

AUX OUT LOCK VOUT POWER

12VOUT
COM

COM
GND

GND

GND
SEN
BUT

12V
NO

NO
NC

NC
RS485 ADD.

Master Device
Connection

The DM10 has to be connected to F18(Master Device) to use the software.

GND GND
EXT

485+ 485A
485- 485B

+ + +
- - -
DC12V DC12V DC12V
GLED

GLED
BEEP

BEEP
485A
485B
GND

GND

WD1
WD0
GND

WD1
WD0
GND

GLED

GLED
BEEP

BEEP
AUX

GLED

GLED
BEEP

BEEP
485A
485B
12V

12V

GND

GND

WD1
WD0
GND

WD1
WD0
GND
AUX

485A
485B
GND

GND

WD1
WD0
GND

WD1
WD0
GND
AUX
12V

12V

12V

12V

RS485 AUX IN READER 1 READER 2 RS485 AUX IN READER 1 READER 2 RS485 AUX IN READER 1 READER 2

Router PWR PWR PWR

AUX OUT LOCK VOUT POWER AUX OUT LOCK VOUT POWER AUX OUT LOCK VOUT POWER
12VOUT

12VOUT

12VOUT
COM

COM
GND

GND

GND
SEN
BUT

COM

COM
12V

GND

GND

GND

COM

COM
SEN
NO

NO

BUT

GND
NC

NC

GND

GND
SEN
12V

BUT

12V
NO

NO
NC

NC

RS485 ADD.
NO

NO
NC

NC

RS485 ADD. RS485 ADD.

1 2 8

An Access Controller can connect to a maximum of

eight DM10.
Each device requires a separate power supply.

3
Quick Start
After proper wiring, please follow the below instructions.
1. Set the RS485 address of DM10 as 2-9.
2. Set the F18 serial port as ”host” ([COMM.]> [serial port]).

Step 1
Open the ZKAccess3.5 software, click [Device]> [New], enter the name
and IP address of F18 , and
then
click [OK].

Step 2
Click [More...] > [Add IO Expansion Board] , check the RS485 address of
DM10, and
then
click [OK].

4
After successful configuration, the Indicator LED flashes every two 2
seconds, indicating that the communication is normal. After adding
successfully, the parameters of the access control unit could be set, please
refer to the ZKAccess 3.5 user manual for further details.

5
ZKTeco Industrial Park, No. 26, 188 Industrial Road,

Tangxia Town, Dongguan, China.

Phone : +86 769 - 82109991

Fax : +86 755 - 89602394

www.zkteco.com

Copyright © 2020 ZKTECO CO., LTD. All Rights Reserved.

6