YSC-8320

USER MANUAL

XI’AN TYPICAL INDUSTRIES CO.,LTD.

 Contents Page

1 Notice 3
1.1 Work environment 3
1.2 Notice of installation 3
1.3 Notice of safety 3
2 Installation and Adjustment 4
2.1 Dimension of controll box 4
2.2 Adjustment of speed controller 4
2.3 Dimension of speed controller bracket (direct-driven) 4
2.4 Dimension of identifier 4
2.5 Dimension of servo motor (direct-driven) 4
2.6 Dimension of servo motor (belt-driven) 5
2.7 Installation of magnetic synchronizer 5
2.8 Installation diagram of system 5
3 Power Connection 6
3.1 Single phase 220V power connection 6
3.2 Three phase 380V power connection 6
4 Connector Diagram 7
5 Function of Operation Box 8
6 Operation of the Front Panel 10
6.1 Diagram of the front panel 10
6.2 Mode parameter setting 10
6.3 Setting of speed 15
6.4 Select of Machine type 16
6.5 Adjust the tacking 17
6.6 Slow start function 18
6.7 Counting the products quantity 18
6.8 Access the special function parameter interface 19
6.9 Resume the default value of parameters 19
6.10 Encrypt the parameter interface 19
7 General Parameter Table 20
7.1 Speed parameter 20
7.2 Time parameter 20
7.3 Enable parameter 21
7.4 Special function parameter (part) 25
1
8 Measurement of Error and Warning 26
9 Signal Checking 27
9.1 Speed controller 27
9.2 Inspector 27
9.3 Button signal 27
9.4 Hall signal of servo motor 28
9.5 Encoder of servo motor 28
9.6 Solenoid function 28
9.7 Code of identifier 28
9.8 Version of software 28
9.9 Output voltage of speed controller 28
10 Measurement of History Errors 28
11 Prompt of Adding Grease 29
12 Motor Reversing 29
13 Parameter Solidifying 29

Appendix：7-segment Display Characters Compare Table 30

2
1. Notice
YSC-8320 is used in system of industry sewing machine. For perfect
operation and safety, installation and operation must be supervised by
professional.

1.1 Work environment

▲ Please use 220V AC in ±10% ranges.
▲ To avoid the false operate, please keep the product away from the
high electromagnetic interference.
▲ Please operate in the area which temperature is 5℃~45℃.
▲ Please operate in the area which humidity is 80% or less.
▲ Please keep the product away from the flammability and exploder.

1.2 Notice of installation

▲ The control box should be installed correctly follow the instruction in
this manual.
▲ Turn off the power and unplug the cord before installation.
▲ The wire must not set to be near the wheel and other movable parts.
▲ To avoid the static interference and current leakage, all grounding
must be done.

1.3 Notice of safety

▲ Turn off the power before maintenance and repairs or raising the
machine arms, or changing needle, or threading needle.
▲ Please don’t open the box except the professional.
▲ When turn on the machine in the first time, use low speed to operate
and check the correct rotation direction.
▲ During machine operation, don’t touch any moving parts.
▲ All moving parts must use the protective device to avoid the body
contact and objects insertion.
▲ When there is water or other liquid, or caustic material on box or
motor, you must stop operation and turn off the power.
▲ All connector shouldn’t be plug and unplug when power on.
▲ The connector should be plug and unplug in the correct method.

3
2. Installation and Adjustment
2.1 Dimension of control box 2.2 Adjustment of speed controller

A：Forward spring
B：Groove
C：Bolt group
D：Back spring
E：Pothook hole for
pedal

2.3 Dimension of speed controller 2.4 Dimension of identifier

bracket (direct-driven)

2.5 Dimension of servo motor (direct-driven)

4
2.6 Dimension of servo motor (belt-driven)

2.7 Installation of magnetic synchronizer

When install
the handwheel,
the first hole
must be vertical
to the plane of
the main axis.

2.8 Installation diagram of system

5
3. Power Connection
3.1 Single phase 220V power connection
Ground wire (green/yellow) must be grounding.

3.2 Three phase 380V power connection

6
4. Connector Diagram

Attention: for direct-driven is safety SW., and for belt-driven is inspector.

7
5. Function of Operation Box
P101 Operation Box Diagram

Function Key Operation

Double start tacking, A is the stitches of forth
sewing; B is the stitches of back sewing. They
Start Tacking are both in range 1~15.
Selection Single start tacking, A is the stitches of forth
sewing; B is the stitches of back sewing. They
are both in range 1~15.
Double end tacking, C is the stitches of back
sewing; D is the stitches of forth sewing. They
End Tacking are both in range 1~15.
Selection Single end tacking, C is the stitches of back
sewing; D is the stitches of forth sewing. They
are both in range 1~15.
▲ As the pedal is stepped forward, the start
tacking(if selected) will be done automatically,
then machine will start normal sewing. Once the
pedal returned to balance, machine will stop
Free Sewing
immediately.
▲ As the pedal stepped backward, the end
tacking, trimming and wiping(if selected) will be
done automatically.

8
 ▲ Once the pedal is stepped forward, all the
seams of bar tacking, A, B, C, D sections will
Bar Tacking be completed with E times, and the trimming
Sewing will be done automatically.
▲ The pedal must be returned to balance for
next sewing.
▲ Once the pedal is stepped forward, F, G
stitches will be completed with E times.
▲ Constant-Stitch Sewing will perform the
number of segments and times as setting, when
the stitches are zero, machine will stop
immediately.
Constant-Stitch
Sewing ▲ If the button is set “ON”, the
Constant-Stitch Sewing will perform
automatically as setting. If it is set “OFF”,
machine will stop immediately once the pedal
returned to balance. As the pedal is stepped
forward again, the rest stitches of current
segment will be completed.
Switch Set the number of segment in Bar Tack or
Selection Constant-Stitch Sewing, or parameter type.
It is available only for constant-stitch sewing.
Constant-Stitch When it is set ‘’ON”,
Sewing a. Once step forward, automatically performed
Automation the stitches of setting.
Selection b. Repeat the action to finish rest the sections
until it finished.
Needle Up /
Select the stop position of needle.
Needle Down
Trimming
Enable or disable the trimming.
Enable
Parameter
Enter or exit parameter function interface.
Function

9
6. Operation of the Front Panel
6.1 Diagram of the front panel

6.2 Mode parameter setting

6.2.1 Mode 1 (Free sewing)
a. How to access the free sewing
Press key will Press key and Press key will
be into parameter to get the show the value of
interface parameter A01 parameter

Press to make Press key to Press key , it

the value “ON”, it save the value will be the free
will be free sewing sewing

10
 b. How to set the times of start tacking
Get the parameter Press to make Press to save
A07, press key the value “ON”, it the value, result as
will show the value will be single start below

Get the parameter Press to make Press to save

A09，press key the value “ON”, it the value, result as
will show the value will be double below

If A07 and A09

are both “OFF”, it
will be no start

c. How to set the times of end tacking

Get the parameter Press to make Press to save

A06, press key the value “ON”, it the value, result as
will show the value will be single end below

11
Get the parameter Press to make Press to save
A08, press key the value “ON”, it the value, result as
will show the value will be double below

If A07 and A09

are both “OFF”, it
will be no end

d. how to set the stitch of start/end tacking

Press and The forth and back
to set the stitch stitch of start as
below

Press and The back and forth

to set the stitch stitch of end as
below

12
6.2.1 Mode 2 (Bar tacking sewing)
a. How to access the bar tacking sewing

Get the parameter Press to make Press key , it

A02, press key the value “ON”, will be the bar
will show the value and to save tacking sewing

b. How to set the stitch of the first round

Press to show Press and The forth and back

the stitch of first to set the forth and stitch of first
round back stitch of round as below
first round

c. How to set the stitch for other round

Press to show Press and The forth and back

the stitch of other to set the forth and stitch of else
round back stitch of round as below
else round

13
 d. How to set the times of bar tacking sewing

Press to show Press to set Result as below

the times the times

6.2.1 Mode 3 (Constant-stitch sewing)

a. How to access the constant-stitch sewing

Get the parameter Press to make Press key , it

A03, press key the value “ON”, will be the C-S
will show the value and to save sewing

b. How to set the segments and stitch

Press to show to set segment

the segment and (1～15), to
stitch set the stitch
(0～99)

14
 c. How to set the stitch of start tacking

Press to show Press and to The forth and back

the stitch of start set the stitch of start stitch of start as below

d. How to set the stitch of end tacking

press to show Press and to The forth and back

the stitch of end set the stitch of end stitch of end as below

e. The setting of start/end tacking times is similar to the free sewing,

the parameter are A10, A11, A12 and A13.

6.3 Setting of speed

6.3.1 How to set the max speed

Get the parameter S01, press Press ～ to set the max

to show the value speed, press to save

6.3.2 The setting of other speed is similar above.

15
6.4 Select of Machine type
The machine type code (O03) is associated with identifier automatically,
the parameter relative would refresh according to machine type. If any wrong
with the identifier, it can be disabled and set by manual, as below:
▲ Press during power on, “ID D” would be displayed then the
identifier is disabled;
▲ Set O03 to according with machine type;
▲ Set O30 to be ”ON” will re-enable the identifier function.

The default value of some parameters are different from machine type,
as below:
Default
S01 S03 S04 S05 S06 T01 T02 A16 O31 O32 O33
Code
01 4000 1800 1800 1800 3000 45 42 OFF ON 1 1440
02 3000 1800 1800 1800 2000 53 48 OFF ON 1 1440
03 4000 1800 1800 1800 3000 45 42 OFF ON 1 1440
04 3000 1800 1800 1800 2000 53 48 OFF ON 1 1440
05 3500 1500 1500 1500 3000 70 55 OFF ON 1 1440
06 2500 1500 1500 1500 2000 70 55 OFF ON 1 1440
07 4000 1800 1800 1800 3000 55 40 ON OFF 0 1440
08 3000 1800 1800 1800 2000 59 45 ON OFF 0 1440
09 2000 1000 1000 1000 1500 55 45 OFF OFF 0 1618
10 4000 1800 1800 1800 3000 55 40 OFF OFF 0 1440
11 3000 1800 1800 1800 2000 59 45 OFF OFF 0 1440
12 3500 1800 1800 1800 2000 45 31 OFF OFF 0 1440

13 2500 1800 1800 1800 2000 55 45 OFF OFF 0 1440

14 3500 1800 1800 1800 2000 57 46 OFF OFF 0 1440

16
6.5 Adjust the tacking
6.5.1 Adjusting of RVE. SOL. action time
For start/end tacking or bar tacking, if unbalanced situation is appeared
during natural direction to reverse direction, please correct it as below:

Find parameter T01

(RVE. SOL. action
time), decrease it.

Find parameter T01

(RVE. SOL. action
time), increase it.

6.5.2 Adjusting of RVE. SOL. release time

For start/end tacking or bar tacking, if unbalanced situation is appeared
during reverse direction to natural direction, please correct it as below:

Find parameter T02

(RVE. SOL. release
time), decrease it.

Find parameter T02

(RVE. SOL. release
time), increase it.

17
6.6 Slow start function
If the Stitches of slow sewing at start (O01) is non-zero, the speed of next
start would be slow sewing speed (S08) during the stitches of O01, and then
associated with speed controller, as below:

6.7 Counting the products quantity

The quantity add 1 after trimming automatically, counting range is
0~9999, as below:
Find parameter A30 Set to “ON” Display the products quantity

Add 1 after trimming Correct by manual Press to exit

18
6.8 Access the special function parameter interface

Press during It will show “O EN” Then could select

power on the O parameter

6.9 Resume the default value of parameters

Find parameter O17 Set to “ON” Press to save

Turn on power again Display “INIT” Then the resumption

sparklingly accomplish

6.10 Encrypt the parameter interface

Find parameter O21 Set to “ON” and Then the password

save needed next time

19
 Press after set Display “OK” if right, Display “NO” if wrong,
then enter parameters then can’t enter
interface parameters interface

7. General Parameter Table

7.1 Speed parameter
SN Name Range Default Description
500～5000 See
S01 Max speed Maximum speed.
（s/m） Page 16
150～500
S02 Min speed 150 Minimum speed.
（s/m）
Speed of start 500～2000 See
S03 Speed of start tacking.
tacking （s/m） Page 16
Speed of end 500～2000 See
S04 Speed of end tacking.
tacking （s/m） Page 16
Speed of bar 500～2000 See
S05 Speed of bar tacking sewing.
tacking sewing （s/m） Page 16
Speed of C-S 500～4000 See Speed of constant-stitch sewing,
S06
sewing （s/m） Page 16 Valid only when A14 is “ON”.
Trimming 150～300
S07 200 Speed adjustment for trimmer.
speed （s/m）
Slow sewing 200～500
S08 400 Slow sewing speed when start.
speed （s/m）

7.2 Time parameter

SN Name Range Default Description
1～200 See
T01 RVS action time Action time of the REV SOL.
(ms) Page 16

20
 1～200 See
T02 RVS release time Release time of the REV SOL.
(ms) Page 16
Action time of 1～200 Timing before the trimmer solenoid is
T03 110
trimming (ms) act.
Delay time of 1～200
T04 20 Timing before the wiper solenoid is act.
wiping (ms)
Action time of 1～200
T05 30 Timing of the wiper solenoid is act.
wiping (ms)
Delay time of foot 1～500 Timing before the foot lifter solenoid is
T06 10
lifter (ms) act.
Release time of 1～500 Timing before the foot lifter solenoid is
T07 50
foot lifter (ms) released.
Time of foot lifter 1～999 Timing of the foot lifter solenoid is act
T08 500
whole output (ms) with whole output.
Time of RVS 1～999 Timing of the reverse solenoid is act
T09 150
whole output (ms) with whole output.
Sensitivity time of 1～200 The action will be greater sensitive
T10 20
Stitch correction (ms) when the value is smaller.
Sensitivity time of 1～300 The keyboard will be greater sensitive
T11 150
keyboard (ms) when the value is smaller.
Time of remove 1～500 The speed controller will be greater
T12 100
shake (ms) sensitive when the value is smaller.

7.3 Enable parameter

SN Name Range Default Description
ON～ When set to “ON”, the free sewing is
A01 Free sewing ON
OFF enable.
Bar tacking ON～ When set to “ON”, the bar tack sewing is
A02 OFF
sewing OFF enable.
ON～ When set to “ON”, the constant-stitch
A03 C-S sewing OFF
OFF sewing is enable.
ON～ When set to “ON”, the stop position will
A04 Up position OFF
OFF be up.
A05 Down position ON～ OFF When set to “ON”, the stop position will

21
 OFF be down.
End tacking 1
ON～ When set to “ON”, the end tacking of free
A06 times of free ON
OFF sewing is 1 times.
sewing
Start tacking 1
ON～ When set to “ON”, the start tacking of
A07 times of free ON
OFF free sewing is 1 times.
sewing
End tacking 2
ON～ When set to “ON”, the end tacking of free
A08 times of free OFF
OFF sewing is 2 times.
sewing
Start tacking 2
ON～ When set to “ON”, the start tacking of
A09 times of free OFF
OFF free sewing is 2 times.
sewing
End tacking 1
ON～ When set to “ON”, the end tacking of
A10 times of C-S ON
OFF constant-stitch sewing is 1 times.
sewing
Start tacking 1
ON～ When set to “ON”, the start tacking of
A11 times of C-S ON
OFF constant-stitch sewing is 1 times.
sewing
End tacking 2
ON～ When set to “ON”, the end tacking of
A12 times of C-S OFF
OFF constant-stitch sewing is 2 times.
sewing
Start tacking 2
ON～ When set to “ON”, the start tacking of
A13 times of C-S OFF
OFF constant-stitch sewing is 2 times.
sewing

Automatically ON～ Valid only in constant-stitch sewing, when

A14 ON
sewing OFF set to “ON”, enable the automatic sewing.

For free sewing, if there is single switch

on machine arms, when set to “OFF” the
Stitch
ON～ switch is reverse switch always. When
A15 correction with OFF
OFF set to “ON”, the switch is reverse switch
single button
at sewing and is stitch correction switch
at stop.

22
 When set to “ON”, enable the reverse
and stitch correction switch both are
Stitch
ON～ See valid. When set to “OFF”, disable the
A16 correction with
OFF Page 16 double key be valid at the same time, and
double button
in this mode, the function of the single
switch is determined by A15.
ON～
A17 Trimming ON When it is “ON”, enable the trimming.
OFF
ON～ When it is “ON”, enable the wiping. When
A18 Wiping ON
OFF A17 is “OFF”, A18 is invalid.
When it is “ON”, enable foot lift. Whether
ON～
A19 Foot lift ON the foot SOL to be connected is detected
OFF
during power on automatically.
When A19 is “ON”, if A20 is set to “ON”,
Foot lift after ON～ the foot lifter will lift automatically after
A20 OFF
stop OFF stop in free sewing and constant-stitch
sewing.
When A19 is “ON”, if A20 is set to “ON”,
Foot lift after ON～
A21 OFF the foot lifter will lift automatically after
trimming OFF
trimming.
It is valid only for constant-stitch sewing.
If enable automatic sewing mode and set
The first the start tacking, the next segment of
segment keep constant-stitch sewing will do
ON～
A22 on with the ON automatically after the start tacking is
OFF
start tacking of finished when A22 is “ON”. When it is
C-S sewing “OFF” or disable the automatic sewing
mode, machine will stop automatically
after the start tacking is finished.

23
 It is valid only for constant-stitch sewing.
If enable automatic sewing mode, the
end tacking and trimming will do
The end automatically after the last segment of
tacking keep constant-stitch sewing is finished when it
ON～
A23 on with the last ON is “ON”. When it is “OFF” or disable the
OFF
segment of automatic sewing mode, machine will
C-S sewing stop automatically after the last segment
of constant-stitch sewing is finished. The
end tacking and trimming will do until
step forward the pedal again.

Stitch It is valid only when A26 is “ON”. When it

correction for ON～ is “ON”, stitch correction is only to be
A24 OFF
whole stitch of OFF whole stitch in constant-stitch sewing.
C-S sewing When it is “OFF”, it can be half.
Stitch
When it is “ON”, stitch correction is only
correction for ON～
A25 OFF to be whole stitch in free sewing. When it
whole stitch of OFF
is “OFF”, it can be half.
free sewing
Stitch
ON～ When it is “ON”, stitch correction function
A26 correction of OFF
OFF of constant-stitch sewing is enabled.
C-S sewing
Move to up When it is “ON”, the machine will move to
ON～
A27 position after OFF up position and stop automatically as
OFF
power on power on.
Foot lifer When the pedal is half back toe down, if it
ON～
A28 acting in foot ON is “ON”, the position is foot lift. If it is
OFF
lift position “OFF”, the position is balance.
Trimmer acting
ON～ When it is “ON”, the trimming will at the
A29 in foot lift OFF
OFF foot lifter position.
position
Counting the
ON～
A30 products OFF See Page 18.
OFF
quantity

24
7.4 Special function parameter (part)
Note: Don’t change these parameters without permission.

SN Name Range Default Descriptions

The stitches of slow sewing at start
Stitches of slow
O01 0～10 0 when trimming is finished. The
sewing at start
speed of slow sewing is set in S08.
See
O03 Machine type 1～30 According to the machine type.
Page 16
The duty cycle of PWM for signal of
Duty of foot lifter 10～99 foot lifter solenoid. The power will be
O05 50
output （％） greater if this value is bigger, at the
same time, the heat is more.
When it is “ON”, the foot lifter
Foot lifter release ON～
O06 ON solenoid will be released
timed OFF
automatically after the time desired.
Initialization of ON～
O17 OFF See Page 19.
parameters OFF
Password required
ON～
O21 to change OFF See Page 19.
OFF
parameters
Run time of lasting 1～60
O23 5 The run time of lasting mode.
mode （s）
Stop time of lasting 1～60
O24 5 The stop time of lasting mode.
mode （s）
The total time of lasting mode. It will
Total time of lasting 1～255
O25 1 be finished automatically when
mode （h）
reached the time.
Lasting mode ON～ When it is “ON”, the lasting mode will
O26 OFF
enable OFF be active.
0: Normal close;
O29 Safety SW. mode 0～1 1
1: Normal open.
ON～
O30 Identifier enable ON See Page 16.
OFF

25
 ON～ See When it is “ON”, the Safety SW is
O31 Safety SW. enable
OFF Page 16 enable.
See 0: Belt driven mode;
O32 Motor drive mode 0～1
Page 16 1: Direct driven mode.
See The scale between motor from
O33 Scale 0～2000
Page 16 machine.
Motor reverse ON～
O52 OFF See Page 29.
enable OFF

8. Measurement of Error and Warning

Error
Causation Measurement
code
E01 Voltage is too high Check the AC power.
E02 Voltage is too low Check the AC power.
E03 Load is too heavy Check the load.
E04 Pedal error Check speed controller, see page 27.
E05 Position check error Check inspector, see page 27.
E06 Encoder of motor error Check encoder, see page 28.
E07 Machine type error Check identifier, see page 28 and 16.
E08 Trimmer SOL error Check SOL whether direct short.
E09 REV SOL error Check SOL whether direct short.
E10 Wiper SOL error Check SOL whether direct short.
E11 Foot lifter SOL error Check SOL whether direct short.
Pedal warning Release the pedal to balance position.
Check Safety SW, or set O29 to match
Safety SW warning
machine type.
Inspector disconnected Motor still can run, but all output signals
warning will be invalid.

26
9. Signal Checking
Press during power on, it will display “TEST” and then enter the

mode of Measurement of Input Signal. Press to change the checking

item, press to show currently SN.

9.1 Speed controller

A, B denote the position of pedal, C, D denote the pull.
Display of the different pedal position as below:
Display code Meanings Descriptions
FS02～FS99 High speed The second segment forward, pull is 02～99.
LS01 Low speed The first segment forward, pull is 01.
BL-- Balance Default.
FP-- Foot lifter The first segment backward.
TM-- Trimming The second segment of backward.
ERRO Fault Speed controller fault or disconnected.

9.2 Inspector
A, B denote the up position, C, D denote the down
position.
Turn the hand wheel by hand equably, display of different
position as below:
Display code Meanings Descriptions
UP-- Needle up position In up position.
--DW Needle down position In down position.
---- Other position Neither in up or down position.
ERRO Fault Both in up and down position.

9.3 Switch signal

A denote SYNC of inspector, B denote REV SW, C
denote COR SW, D denote Safety SW. “0” to open, “1” to
close.

27
9.4 Hall signal of servo motor
Turn the hand wheel by hand equably, display the hall
signal of motor, range is 0~7. If the fault state appeared, then
display “ERRO”.

9.5 Encoder of servo motor

Turn the hand wheel by hand equably, display the encode
count of motor, up to O33 then reset, the error is ±5 normally.

9.6 Solenoid function

Through ~ to test the SOL, as below:
-- Trimmer SOL -- REV SOL
-- Wiper SOL -- Foot Lifter SOL
“N” denote no action, “A” denote acting.

9.7 Code of identifier

Display the code of identifier, see page 16. Display
“ERRO” while fault.

9.8 Version of software

For example, the version is v 1.00。

9.9 Output voltage of speed controller

Display the output voltage of speed controller, unit is ×
0.01V.

10. Measurement of History Errors

The system can save the error code automatically when error occurred.
Checking the history error by operation as below:
▲ Press during power on, then display “ER D”;
▲ Press to check the 10 error code of recent;
▲ Display “NO” if there is no error;
▲ Else display the error code, see page 26.

28
11. Prompt of Adding Grease
The whole operating stitches would be saved in memory hardware. If this
quantity of direct-driven machine is more than 2 hundred million, sparkling
“OIL” would be displayed to tell user adding grease, during the time press
to confirm, then become to wait the next 2 hundred million stitches.
If press during power on, the times of user confirm and whole
operating stitches would be displayed as below:
For example: user confirm 1 time, and the machine has been ran 1.5
hundred million stitches.

12. Motor Reversing

If machine head locked, the function of motor reversing would be useful.
Operating as below:
▲ Press during power on, then display “RV E”;
▲ Through pedal to run motor reversing;
▲ If the problem solved, set parameter O52 “OFF” to resume normal
status.

13. Parameter Solidifying

If user want to change some parameter’s default value, operating as
below:
Select parameter (such as Display “S OK” after accomplished,
T01), press to solidify. then the default of T01 is changed to
user’s setting.

29
Appendix: 7-segment Display Characters Compare Table

Arabic Number

Actual 0 1 2 3 4 5 6 7 8 9

Display

English Alphabet

Actual A B C D E F G H I J

Display

Actual K L M N O P Q R S T

Display

Actual U V W X Y Z

Display

30
Add：No.1 Taibai South Road,
Xi’an, P.R.China-710068
Tel：+86-29-88279162 88279163
Fax：029-88279161 83911111
E-mail: [email protected]
Http://www.chinatypical.com
V1