WWW.DIESELSHIP.

COM 1

FEBRUARY 2020
MEP – X
2002

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II SET A

TIME ALLOWED - 3 HOURS

Total Marks - 100
(India 2020)

NOTE :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage

Q1. Describe a suitable means of withdrawal procedure for the removal of keyless propellers.
2009/SR7 2009/SR3 2008/SR3 2007/SR5 2007/SR2 2006/SR9 2012/SR7 2020/FEB/Q1

Q2. A marine diesel engine fresh water cooler end cover is badly corroded and holed. Other than replacing it,
suggest some measures of repairing it (a) while in operation. (b) When not in operation. Repair procedures must
be effective. practicable and innovative.
2020/FEB/Q2

Q3. With reference to Main Engine Fuel Pumps;

(a) Explain how the setting of a variable injection timing fuel pump is checked and adjusted.
(b) State why it may be necessary to adjust the settings of a variable injection timing fuel pump.
2015/SR09 2017/SR01 2018/SR04 2019/MAR 2020/JAN 2020/FEB/Q3

Q4. A. During the weighment of CO2 bottles required for total flooding of Engine room, it was observed that few
bottles are less than the original capacity. State the reasons for the same and checks / tests to be made prior
refilling; B. State how often the CO2 bottles are required to be weighed and pressure tested.
2008/SR1 2007/SR8 2006/SR7 2007/SR10 2007/SR2 2006/SR8 05-/EMG
2010/SR2 2015/SR10 2018/SR02 2020/FEB/Q4

Q5. Express your reactions and state the subsequent investigation you would make if a laboratory report on a
used diesel engine oil sample indicated the presence of appreciable amounts of: -
A. Iron; B. Copper, Antimony and Tin; C. Silicon.
2015/SR09 2017/SR01 2018/SR04 2020/JAN 2020/FEB/Q5

WWW.DIESELSHIP.COM DIESELSHIP
 WWW.DIESELSHIP.COM 2
Q6. Write short notes on following:
A. Magnetic Particle Inspection (MPI)
B. Ultrasonic Testing (UT)
C. Radiographic Testing (RT).
2018/SR09 2019/MAR 2020/JAN 2020/FEB/Q6

Q7. With reference to Marine Diesel engines:

(a) Describe how crankshaft alignment is checked.
(b) Identify with reasons the causes of crankshaft misalignment.
(c) State how the measurements are recorded.
2020/FEB/Q7

Q8. Severe engine vibration has recently become evident when the main engine for which you are responsible
operates within a certain speed range –
A. State, with reasons, the possible causes of such vibration;
B. State the consequences of operating the engine under such vibratory conditions;
C. Describe the procedure you, as Second Engineer, would implement in order to investigate and rectify the
problem.
2011/SR9 2012/SR4 2013/SR1 2013/SR09 2014/SR11 2015/SR04 2015/SR06
2017/SR03 2017/SR04 2017/SR07 2017/SR09 2018/SR03 2018/SR07 2018/SR11
2019/JUN 2019/DEC 2020/FEB/Q8

Q9. What are the effects of following on the sluggishness of steering gear operations;
A. Air entrapped in hydraulic oil;
B. Worn pins and weak springs in hunting gear;
C. Shock valves leaking
2008/SR9 2010/SR11 2010/SR8 2011/SR9 2012/SR3 2013/SR3 2013/SR09
2014/SR10 2015/SR02 2015/SR04 2020/FEB/Q9

Note : If you are looking for answers prepared in organized manner with
clear drawings please visit our website by CLICKING HERE

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

JANUARY 2020
2001 – MEP

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
TIME ALLOWED - 3 HOURS
Total Marks - 100
Instructions: -

1. Answer SIX questions only

2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage

Q1: Your ship after having been accidentally grounded was taken to a dry-dock for inspection and
necessary repairs. What defects would you look for in the following parts, that may have sustained
damage due to grounding and suggest methods of repairs and tests that may be required to be carried
out to the defects noticed:
A. Propeller and tail end shaft
B. Main engine crankshaft.
2009/SR4 2008/SR7 2006/SR5 2006/SR1 2011/SR3 2010/SR10 2015/SR09
2015/SR12 2017/SR1 2017/SR06 2017/SR08 2018/SR04 2020/JAN

Q2. Write short note on the followings –

A. Metal – locking; B.TIG and MIG welding; C. Brazing; D. Soldering.
2007/SR08 2012/SR11 2014/SR02 2014/SR03 2014/SR12 2015/SR08 2016/SR02
2016/SR03 2016/SR06 2016/SR09 2016/SR10 2016/SR12 2017/SR10 2017/SR12
2018/SR01 2018/SR03 2018/SR04 2018/SR08 2019/JUN 2019/DEC 2020/JAN

Q3. With reference to Main Engine Fuel Pumps;

(a) Explain how the setting of a variable injection timing fuel pump is checked and adjusted.
(b) State why it may be necessary to adjust the settings of a variable injection timing fuel pump.
2015/SR09 2017/SR01 2018/SR04 2019/MAR 2020/JAN

Q4. With respect to the operation of two stage reciprocating air compressor. Explain:
A. The causes of occasional lifting of 2nd stage relief valve.
B. Breakage of valve plates.
C. Puncture of bursting disc of 1st stage intercooler.
D. Noticeable reduction in capacity of the compressors over a period of time.
2018/SR09 2018/SR11 2019/JAN 2019/MAR 2019/APR 2019/JUN 2019/JULY 2019/SEP
2019/NOV 2019/DEC 2020/JAN

Q5. Express your reactions and state the subsequent investigation you would make if a laboratory report
on a used diesel engine oil sample indicated the presence of appreciable amounts of: -
A. Iron; B. Copper, Antimony and Tin; C. Silicon.
2015/SR09 2017/SR01 2018/SR04 2020/JAN

WWW.DIESELSHIP.COM
WWW.DIESELSHIP.COM 2
Q6. Write short notes on following:
A. Magnetic Particle Inspection (MPI)
B. Ultrasonic Testing (UT)
C. Radiographic Testing (RT)
2018/SR09 2019/MAR 2020/JAN

Q7. With regard to keeping the gas side of boilers in good condition discusses EACH of the following:
A. the mechanism of combustion, stating the factors which are important to good combustion;
B. Oil fuel treatments;
C. Soot removal equipment;
2009/SR6 2008/SR7 2008/SR1 2007/EMG 2007/SR8 2006/SR7 2006/SR4
2006/SR1 2011/SR3 2010/SR10 2010/SR9 2010/SR6 2012/SR4 2012/SR8
2013/SR8 2014/SR01 2014/SR9 2014/SR12 2016/SR03 2016/SR10 2016/SR02
2016/SR06 2017/SR07 2017/SR12 2018/SR01 2018/SR03 2018/SR04 2018/SR08
2019/MAR 2020/JAN

Q8. What is Rocking test of Deck Crane? Explain the procedure of rocking test. Tabulate and indicate
fault finding procedure. What is the action taken if deviation is out of limit?
2018/SR09 2018/SR11 2019/JAN 2019/MAR 2019/NOV 2020/JAN

Q9. Using sketches explain the difference between Pulse and constant pressure turbocharger systems.
A. In the event of a Pulse turbocharger becoming inoperative due to mechanical breakdown explain the
modifications required to allow the engine to operate safely.
B. State the instruction you as second engineer would issue regarding the additional engine monitoring
requirements following the steps taken in (a).
2015/SR09 2017/SR01 2018/SR04 2020/JAN

Note : If you are looking for answers prepared in organized manner with
clear drawings please visit our website by CLICKING HERE

WWW.DIESELSHIP.COM
 WWW.DIESELSHIP.COM 1

MARCH 2020
2003 MEP

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II SET A

TIME ALLOWED - 3 HOURS

Total Marks - 100
(India 2020)

NOTE :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. All unused pages of answer script must be cancelled out by two lines (X) across the page.

Q1. With reference to reciprocating air compressors explain the cause of the following faults.
A. Collapse of discharge valve springs;
B. Breakage of plate valves;
C. Overheating of the discharge air with an unrestricted air intake;
D. Inoperative piston rings.

2008/SR6 2011/SR2 2006-07/EM 2011/SR8 2012/SR6 2013/SR4 2013/SR12

2014/SR07 2014/SR08 2016/SR01 2016/SR07 2019/FEB 2019/AUG 2019/OCT
2020/MR/Q1

Q2. What is Metal-locking? What types of repairs are carried out by metal-locking? Describe the repair procedure
using Metal-Locking.
2019/AUG 2019/OCT 2020/MAR/Q2

Q3. With the aid of a simple sketch, explain the “trouble spots” in a basic air-conditioning unit with reference to
your sketch, explain the following: -
i. How the problem of increase in humidity on cooled air is overcome?
ii. How discomfort caused by the excessive drying effect of heated air is overcome?
2007/SR03 2012/SR01 2012/SR02 2012/SR12 2014/SR03 2014/SR12 2015/SR08
2016/SR09 2016/SR12 2017/SR06 2017/SR07 2017/SR08 2017/SR10 2018/SR08
2018/SR09 2019/JAN 2019/FEB 2019/APR 2019/JUN 2019/JULY 2019/AUG
2019/SEP 2019/OCT 2019/NOV 2019/DEC 2020/MAR/Q3

Q4. Explain why auxiliary engine bottom-end bolts are prone to failure, even under normal running conditions.
Identify those features, incorporated into the design of bottom-end bolts, to inhibit failure. Explain how this
tendency is either aggravated or inhibited during maintenance and what checks are to be carried out.
2019/AUG 2019/OCT 2020/MAR/Q4

WWW.DIESELSHIP.COM DIESELSHIP
 WWW.DIESELSHIP.COM 2
Q5. Enumerate the maintenance routines carried out for the proper functioning of the following systems:
A. Water hyper mist system
B. Smoke detection system
C. Quick closing valves
D. Fire hydrants and hoses.
2018/SR09 2019/FEB 2019/MAR 2019/AUG 2019/OCT 2019/NOV 2020/MAR/Q5

Q6. A marine diesel engine fresh water cooler end cover is badly corroded and holed. Other than replacing it,
suggest some measures of repairing it (a) while in operation. (b) When not in operation. Repair procedures must
be effective. practicable and innovative.
2020/FEB/Q2 2020/FEB/Q6

Q7. With reference to Auxiliary boiler safety valve;

A. Describe with the aid of Sketch the safety valve for an auxiliary boiler;
B. Identify with reasons. The parts that require particularly close attention during overhaul;
C. Describe how the safety valves are reset after an overhaul.
2009/SR7 2008/SR6 2007/SR5 2006/SR9 2011/SR2 2011/SR7 2011/SR11 2013/SR02 2019/FEB
2019/AUG

Q8. If soon after joining a motor ship, you found a number of holding down bolts slack and fretting to have
occurred in the area of slack bolts describe how you would handle the situation?
2019/AUG 2019/OCT 2020/MAR/Q8

Q9. With reference to fire pumps.

A. Explain how and when fire pumps should be tested, what are the requirements as per SOLAS74, as amended
B. Describe the routine maintenance to be carried out on the various fittings on a fire line, giving testing
pressure where appropriate.
C. Describe briefly how will you dismantle a fire pump for survey. Give details of factors which will decide
replacing the parts.
2020/MAR/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

DECEMBER 2020
2012 MEP

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II

TIME ALLOWED - 3 HOURS

Total Marks - 100
(India 2020)

NOTE :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. All unused pages of answer script must be cancelled out by two lines (X) across the page.

Q1. Write short note on the followings –

A. Metal – locking; B.TIG and MIG welding; C. Brazing; D. Soldering.
2007/SR08 2012/SR11 2014/SR02 2014/SR03 2014/SR12 2015/SR08 2016/SR02
2016/SR03 2016/SR06 2016/SR09 2016/SR10 2016/SR12 2017/SR10 2017/SR12
2018/SR01 2018/SR03 2018/SR04 2018/SR08 2019/JUN 2019/DEC 2020/JAN
2020/OCT/Q2 2020/DEC/Q1

Q2. With the aid of a simple sketch, explain the “trouble spots” in a basic air-conditioning unit with reference
to your sketch, explain the following: -
i. How the problem of increase in humidity of cooled air is overcome?
ii. How discomfort caused by the excessive drying effect of heated air is overcome?
2007/SR03 2012/SR01 2012/SR02 2012/SR12 2014/SR03 2014/SR12 2015/SR08
2016/SR09 2016/SR12 2017/SR06 2017/SR07 2017/SR08 2017/SR10 2018/SR08
2018/SR09 2019/JAN 2019/FEB 2019/APR 2019/JUN 2019/JULY 2019/AUG
2019/SEP 2019/OCT 2019/NOV 2019/DEC 2020/MAR/Q3 2020/NOV/Q2 2020/DEC/Q2

Q3. Accidents regularly occur due to premature or accidental release of Co2 into machinery spaces With
reference to this enumerate the procedure or arrangement that you as 2nd engineer would adopt with respect
of the following
A. Contractors working on Co 2 system;
B. Understanding between bridge and engine room in the event of a machinery space fire;
C. Familiarizing staff with the system;
D. Checks and tests are carried out before putting system in operation?
2011/SR4 2007/SR3 2010/SR1 2012/SR1 2012/SR2 2013/SR1 2013/SR8
2014/SR4 2014/SR11 2017/SR07 2018/SR03 2020/DEC/Q3

Q4. Briefly describe your action plan on following exigencies:

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
A. Leaky economizer tube, while at sea;
B. Leaky intercooler of main air compressor, while maneuvering.
2008/SR9 2010/SR11 2010/SR8 2013/SR10 2014/SR10 2014SR11 2015/SR06
2016/SR11 2017/SR04 2017/SR07 2017/SR09 2018/SR03 2018/SR07 2018/DEC
2019/JAN 2019/JUN 2019/DEC 2020/DEC/Q4

Q5. As a second engineer, list out all the hazards identified with regard to cylinder head lifting job during main
engine overhaul. Explain how do you carry out risk assessment for above mentioned job.
2020/NOV/Q1 2020/DEC/Q5

Q6. Explain how EACH of the following hull defects should be dealt with;
A. A cracked weld; B. A severe indentation in way of a frame; C. Surfaces suffering from general corrosion
although the extent of wastage does not warrant plate replacement; D. A bilge head fractured at the forward
end.
2007/SR3 2012/SR1 2012/SR2 2012/SR12 2013/SR6 2014/SR01 2014/SR03
2014/SR12 2015/SR01 2015/SR08 2015/SR15 2016/SR02 2016/SR06 2016/SR09
2016/SR12 2017/SR06 2017/SR08 2017/SR10 2017/SR12 2018/SR01 2020/DEC/Q6

Q7. With respect to hydraulic Ram steering gears;

A. What emergency locking device can be used in order to speedily bring the steering gear to rest? State one
reason the best angular position to lock the steering gear.
B. Use a simple sketch to show where the Jumping (top) and wear down (bottom) rudder carrier ring clearances
can be measured. Indicate what clearances you would expect with a new steering gear;
C. State the consequences of the wear down clearances being reduced to less than zero.
2011/SR4 2010/SR4 2010/SR3 2010/SR2 2012/SR1 2014/SR01 2014/SR03 2014/SR4
2014/SR12 2015/SR01 2015/SR08 2016/SR02 2016/SR06 2016/SR12 2017/SR07 2017/SR10
2017/SR12 2018/SR01 2020/DEC/Q7

Q8. Explain in detail how you would isolate one of sprinkler system for routine maintenance. Describe all tests
and inspections you would make and how you would return the system to service.
2008/SR12 2008/EMG 2007/SR2 2011/SR4 2011/SR4 2009/SR1 2008/SR4
2008/SR7 2011/SR9 2012/SR4 2012/SR10 2012/SR11 2013/SR1 2013/SR8
2013/SR09 2014/SR02 2014/SR11 2015/SR03 2015/SR04 2015/SR06 2016/SR03
2016/SR10 2016/SR11 2017/SR04 2017SR09 2018/SR07 2018/SR11 2019/FEB
2019/JUN 2019/JULY 2019/SEP 2020/NOV/Q9 2020/DEC/Q8

Q9. A. State the circumstances owing to which it may be necessary to renew a cylinder liner;
B. Explain how the liner is removed
C. Explain how the new liner is fitted;
C. State the important checks to be made before and after fitting cylinder liner.
2010/SR01 2005/SR02 2012/SR01 2012/SR12 2013/SR01 2013/SR8 2013/SR10
2013/SR11 2014/SR01 2014/SR03 2014/SR11 2014/SR12 2015/SR01 2015/SR08
2015/SR11 2016/SR06 2016/SR12 2017/SR03 2017/SR10 2017/SR11 2017/SR12
2018/SR01 2018/SR09 2018/OCT 2019/JAN 2019/MAR 2019/APR 2020/OCT/Q8
2020/DEC/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 3

WWW.DIESELSHIP.COM DIESELSHIP
 WWW.DIESELSHIP.COM 1

FEBRUARY 2020
MEP – X
2002

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II SET A

TIME ALLOWED - 3 HOURS

Total Marks - 100
(India 2020)

NOTE :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage

Q1. Describe a suitable means of withdrawal procedure for the removal of keyless propellers.
2009/SR7 2009/SR3 2008/SR3 2007/SR5 2007/SR2 2006/SR9 2012/SR7 2020/FEB/Q1

Q2. A marine diesel engine fresh water cooler end cover is badly corroded and holed. Other than replacing it,
suggest some measures of repairing it (a) while in operation. (b) When not in operation. Repair procedures must
be effective. practicable and innovative.
2020/FEB/Q2

Q3. With reference to Main Engine Fuel Pumps;

(a) Explain how the setting of a variable injection timing fuel pump is checked and adjusted.
(b) State why it may be necessary to adjust the settings of a variable injection timing fuel pump.
2015/SR09 2017/SR01 2018/SR04 2019/MAR 2020/JAN 2020/FEB/Q3

Q4. A. During the weighment of CO2 bottles required for total flooding of Engine room, it was observed that few
bottles are less than the original capacity. State the reasons for the same and checks / tests to be made prior
refilling; B. State how often the CO2 bottles are required to be weighed and pressure tested.
2008/SR1 2007/SR8 2006/SR7 2007/SR10 2007/SR2 2006/SR8 05-/EMG
2010/SR2 2015/SR10 2018/SR02 2020/FEB/Q4

Q5. Express your reactions and state the subsequent investigation you would make if a laboratory report on a
used diesel engine oil sample indicated the presence of appreciable amounts of: -
A. Iron; B. Copper, Antimony and Tin; C. Silicon.
2015/SR09 2017/SR01 2018/SR04 2020/JAN 2020/FEB/Q5

Q6. Write short notes on following:

A. Magnetic Particle Inspection (MPI)

This QR code contains information of the purchaser of this book. Circulating, copying, reproducing this book will attract severe
copyright punishments under section 63 of the copyright act, 1957. PURCHASER OF THIS BOOK WILL BE HELD RESPOSNOIBLE.
 WWW.DIESELSHIP.COM 2
B. Ultrasonic Testing (UT)
C. Radiographic Testing (RT).
2018/SR09 2019/MAR 2020/JAN 2020/FEB/Q6

Q7. With reference to Marine Diesel engines:

(a) Describe how crankshaft alignment is checked.
(b) Identify with reasons the causes of crankshaft misalignment.
(c) State how the measurements are recorded.
2020/FEB/Q7

Q8. Severe engine vibration has recently become evident when the main engine for which you are responsible
operates within a certain speed range –
A. State, with reasons, the possible causes of such vibration;
B. State the consequences of operating the engine under such vibratory conditions;
C. Describe the procedure you, as Second Engineer, would implement in order to investigate and rectify the
problem.
2011/SR9 2012/SR4 2013/SR1 2013/SR09 2014/SR11 2015/SR04 2015/SR06
2017/SR03 2017/SR04 2017/SR07 2017/SR09 2018/SR03 2018/SR07 2018/SR11
2019/JUN 2019/DEC 2020/FEB/Q8

Q9. What are the effects of following on the sluggishness of steering gear operations;
A. Air entrapped in hydraulic oil;
B. Worn pins and weak springs in hunting gear;
C. Shock valves leaking
2008/SR9 2010/SR11 2010/SR8 2011/SR9 2012/SR3 2013/SR3 2013/SR09
2014/SR10 2015/SR02 2015/SR04 2020/FEB/Q9

Note : If you are looking for answers prepared in organized manner with
clear drawings please visit our website by CLICKING HERE

This QR code contains information of the purchaser of this book. Circulating, copying, reproducing this book will attract severe
copyright punishments under section 63 of the copyright act, 1957. PURCHASER OF THIS BOOK WILL BE HELD RESPOSNOIBLE.
WWW.DIESELSHIP.COM 1

NOVEMBER 2020
2011 MEP

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II SET A

TIME ALLOWED - 3 HOURS

Total Marks - 100
(India 2020)

NOTE :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. All unused pages of answer script must be cancelled out by two lines (X) across the page.

Q1. When ship is in dry dock, as a Second Engineer, describe inspections you would make prior to the start of
work, during the work and after completion of the work of the following: -
(a) Large sea water inlet chest and valves;
(b) Forward end of ship;
(c) Propeller and stern bush;
2020/NOV/Q1

Q2. With the aid of a simple sketch, explain the “trouble spots” in a basic air-conditioning unit with reference
to your sketch, explain the following: -
i. How the problem of increase in humidity on cooled air is overcome?
ii. How discomfort caused by the excessive drying effect of heated air is overcome?
2007/SR03 2012/SR01 2012/SR02 2012/SR12 2014/SR03 2014/SR12 2015/SR08
2016/SR09 2016/SR12 2017/SR06 2017/SR07 2017/SR08 2017/SR10 2018/SR08
2018/SR09 2019/JAN 2019/FEB 2019/APR 2019/JUN 2019/JULY 2019/AUG
2019/SEP 2019/OCT 2019/NOV 2019/DEC 2020/MAR/Q3 2020/NOV/Q2

Q3. Write short notes on following:

A. Magnetic Particle Inspection (MPI)
B. Ultrasonic Testing (UT)
C. Radiographic Testing (RT).
2018/SR09 2019/MAR 2020/JAN 2020/FEB/Q6 2020/NOV/Q3

Q4. With reference to Auxiliary boiler safety valve;

A. Describe with the aid of Sketch the safety valve for an auxiliary boiler;
B. Identify with reasons. The parts that require particularly close attention during overhaul;
C. Describe how the safety valves are reset after an overhaul.
WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2
2009/SR7 2008/SR6 2007/SR5 2006/SR9 2011/SR2 2011/SR7 2011/SR11 2013/SR02 2019/FEB
2019/AUG 2020/NOV/Q4

Q5. As a second engineer, list out all the hazards identified with regard to cylinder head lifting job during main
engine overhaul. Explain how do you carry out risk assessment for above mentioned job.
2020/NOV/Q1

Q6. With reference to Main Engine Fuel Pumps;

(a) Explain how the setting of a variable injection timing fuel pump is checked and adjusted.
(b) State why it may be necessary to adjust the settings of a variable injection timing fuel pump.
2015/SR09 2017/SR01 2018/SR04 2019/MAR 2020/JAN 2020/FEB/Q3 2020/NOV/Q6

Q7. Under Continuous survey of machinery (CSM) bottom end bearing of a large 2stroke slow speed engine is
due for survey;
A. As 2nd engineer, explain the procedure involved in complete inspection of a bottom end bearing;
B. List the precaution to be taken;
C. Indicate the reasons for possible defects which could be encountered and state how they may be rectified;
D. What test are carried out on completion of survey and re-assembly.
2009/SR8 2007/SR3 2010/SR1 2012/SR1 2012/SR12 2013/SR1 2013/SR10
2013/SR11 2014/SR01 2014/SR11 2014/SR12 2015/SR01 2015/SR03 2015/SR06
2015/SR08 2016/SR02 2016/SR06 2014/SR03 2016/SR11 2016/SR12 2017/SR03
2017/SR04 2017/SR09 2017/SR10 2017/SR12 2018/SR01 2018/SR07 2020/NOV/Q7

Q8. Describe the procedure to be undertaken when, upon a routine schedule for changing fuel injector on a
main engine, it is found that the injector body is seized and cannot be removed by conventional means.
2020/NOV/Q8

Q9. Explain in detail how you would isolate one of sprinkler system for routine maintenance. Describe all tests
and inspections you would make and how you would return the system to service.
2008/SR12 2008/EMG 2007/SR2 2011/SR4 2011/SR4 2009/SR1 2008/SR4
2008/SR7 2011/SR9 2012/SR4 2012/SR10 2012/SR11 2013/SR1 2013/SR8
2013/SR09 2014/SR02 2014/SR11 2015/SR03 2015/SR04 2015/SR06 2016/SR03
2016/SR10 2016/SR11 2017/SR04 2017SR09 2018/SR07 2018/SR11 2019/FEB
2019/JUN 2019/JULY 2019/SEP 2020/NOV/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 1

OCTOBER 2020
2010 MEP

EXAMINATION OF MARINE ENGINEER OFFICER

Function: Maintenance & Repair at Management Level
MARINE ENGINEERING PRACTICE
M.E.O. CLASS II SET A

TIME ALLOWED - 3 HOURS

Total Marks - 100
(India 2020)

NOTE :
1. Answer SIX questions only
2. All Questions carry equal marks
3. Neatness in handwriting and clarity in expression carries weightage
4. Illustration of an answer with clear sketches / diagrams carries weightage.
5. All unused pages of answer script must be cancelled out by two lines (X) across the page.

Q1. Explain why auxiliary engine bottom-end bolts are prone to failure, even under normal running conditions.
Identify those features, incorporated into the design of bottom-end bolts, to inhibit failure. Explain how this
tendency is either aggravated or inhibited during maintenance and what checks are to be carried out.
2019/AUG 2019/OCT 2020/MAR/Q4 2020/OCT/Q1

Q2. Write short note on the followings –

A. Metal – locking; B.TIG and MIG welding; C. Brazing; D. Soldering.
2007/SR08 2012/SR11 2014/SR02 2014/SR03 2014/SR12 2015/SR08 2016/SR02
2016/SR03 2016/SR06 2016/SR09 2016/SR10 2016/SR12 2017/SR10 2017/SR12
2018/SR01 2018/SR03 2018/SR04 2018/SR08 2019/JUN 2019/DEC 2020/JAN
2020/OCT/Q2

Q3. With respect to the operation of two stage reciprocating air compressor. Explain:
A. The causes of occasional lifting of 2nd stage relief valve.
B. Breakage of valve plates.
C. Puncture of bursting disc of 1st stage intercooler.
D. Noticeable reduction in capacity of the compressors over a period of time.
2018/SR09 2018/SR11 2019/JAN 2019/MAR 2019/APR 2019/JUN 2019/JULY 2019/SEP
2019/NOV 2019/DEC 2020/JAN 2020/OCT/Q3

Q4. Discuss on the classification society requirements with regard to maintenance and continuous survey of
machinery.
2020/OCT/Q4

Q5. A single forged shaft for a small gear pump is broken in the middle. Suggest some emergency repairs to
the shaft to enable run the pump. State the type of repair and procedure for carrying out the repair. What is the
most viable alternative to repair if no spares are available?
2013/SR12 2015/SR01 2016/SR07 2020/OCT/Q5

WWW.DIESELSHIP.COM DIESELSHIP
WWW.DIESELSHIP.COM 2

Q6. Describe the hull inspection that you would carry out as the senior engineer of ship in dry dock stating
what defects you may find and the repairs that may be necessary with respect to;
A. Shell plating; B. Forward end of ship; C. Aft end of ship; D. Opening in shell plating; E. Rudder; F. Propeller
and stern tube;
2010/SR2 2008/SR4 06-07/EM 2006/SR4 2006/SR2 2010/SR1 2011/SR7
2011/SR11 2013/SR02 2015/SR7 2015/SR11 2017/SR11 2018/OCT 2020/OCT/Q6

Q7. An Auxiliary boiler is periodically unattended and equipped with alarms to cover low water level, high steam
pressure, and air and flame failure.
A. State why and how fuel the burners are automatically cut off under alarm conditions of water level, steam
pressure, air and flame failure.
B. Describe how and when each of the above alarms is tested without endangering the boiler.
2008/SR3 2011/SR7 2006-2007/EMG 2010/SR9 2011/SR22 2014/SR4 2015/SR07
2020/OCT/Q7

Q8. A. State the circumstances owing to which it may be necessary to renew a cylinder liner;
B. Explain how the liner is removed
C. Explain how the new liner is fitted;
C. State the important checks to be made before and after fitting cylinder liner.
2010/SR01 2005/SR02 2012/SR01 2012/SR12 2013/SR01 2013/SR8 2013/SR10
2013/SR11 2014/SR01 2014/SR03 2014/SR11 2014/SR12 2015/SR01 2015/SR08
2015/SR11 2016/SR06 2016/SR12 2017/SR03 2017/SR10 2017/SR11 2017/SR12
2018/SR01 2018/SR09 2018/OCT 2019/JAN 2019/MAR 2019/APR 2020/OCT/Q8

Q9. Abnormal vibration has been observed in an HFO purifier while in operation. Explain the areas you plan to
investigate for rectifying the faults and put back the purifier back to normal operations keeping in view that no
reduction in vibration has been noticed even after desludging the purifier couple of times.
2018/SR09 2019/JAN 2019/MAR 2019/APR 2019/JUN 2019/JULY 2019/SEP
2019/NOV 2020/OCT/Q9

PLEASE CLICK HERE TO PURCHASE OUR ORIGINAL BOOKS. WE HAVE SOLVED ALL PAST EXAM PAPERS OF
LAST 15 YEARS. CLEAN CONTENT, CAD DRAWING WITH OUR 15 YEARS OF EXPERTISE IN MARITIME
PUBLISHING

WWW.DIESELSHIP.COM DIESELSHIP