Local regulations may restrict the use of this product to below the conditions quoted.

In the interests of development and improvement of the product, we reserve the right to change the specification without notice. © Copyright 2016

TI-P133-77
ST Issue 4

M21Si ISO and M21Vi ISO

Reduced Bore Ball Valves
DN15 to DN150 Flanged PN40
Description
Both the M21Si and M21Vi are reduced bore ball valves, with a
single piece body, having ISO mounting as standard. They are
designed to be isolating valves, which can be used with the
majority of industrial fluids, not control valves.
DN15 to DN50
Available types
M21Si2 ISO Zinc plated carbon steel body, PDR 0.8 seats.

M21Si3 ISO Stainless steel body, PDR 0.8 seats.

M21Vi2 ISO Zinc plated carbon steel body, PTFE seats.

M21Vi3 ISO Stainless steel body, PTFE seats.

Standards
These products fully comply with the requirements of the European
Pressure Equipment Directive 97 / 23 / EC and carry the mark
when so required.

Certification
These product are available with certification to EN 10204 3.1.
Note: All certification / inspection requirements must be stated at
the time of order placement.

DN65
Sizes and pipe connections
DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80, DN100
and DN150
Standard flange: EN 1092 PN40
Face-to-face dimensions:
- DN15 to DN100 according to DIN 3202 F4.
- DN25 to DN150 according to BS 2080.

Technical data
Flow characteristic Modified linear

Port Reduced bore

Leakage test procedure to ISO 5208 (Rate A) / EN 12266-1 (Rate A)

Antistatic device Complies with ISO 7121 and BS 5351

Page 1 of 7
Pressure / temperature limits
M21Si2 ISO and M21Si3 ISO - PDR 0.8 seats


Temperature °C

 Steam
 saturation
 curve


        
Pressure bar g

M21Vi2 ISO and M21Vi3 ISO - PTFE seats



Temperature °C


Steam
 saturation
 curve


    
Pressure bar g

The product must not be used in this region.

Body design conditions PN40

M21Si 40 bar g @ 120 °C

PMA Maximum allowable pressure
M21Vi 40 bar g @ 120 °C

M21Si 260 °C @ 0 bar g

TMA Maximum allowable temperature
M21Vi 230 °C @ 0 bar g

Minimum allowable temperature -29 °C

M21Si 17.5 bar g

PMO Maximum operating pressure for saturated steam service
M21Vi 10.0 bar g

TMO Maximum operating temperature 260 °C @ 0 bar g

Minimum operating temperature

-29 °C
Note: For lower operating temperatures consult Spirax Sarco

PMX Maximum differential pressure is limited to the PMO

Designed for a maximum cold hydraulic test pressure of 60 bar g

Page 2 of 7 TI-P133-77 ST Issue 4

M21Si ISO and M21Vi ISO Reduced Bore Ball Valves DN15 to DN150 Flanged PN40
DN15 to DN50
21

20

16

17
15
14
13
10

25 9
26
9
4

1 18 5 3 5 6 2

Materials
No. Part Material

M21Si2 ISO and M21Vi2 ISO Zinc plated carbon steel ASTM A216 WCB
1 Body
M21Si3 ISO and M21Vi3 ISO Stainless steel ASTM A351 CF8M

M21Si2 ISO and M21Vi2 ISO Zinc plated carbon steel SAE 1040
2 Insert
M21Si3 ISO and M21Vi3 ISO Stainless steel AISI 316

3 Ball Stainless steel AISI 316

4 Stem Stainless steel AISI 316

M21Si2 ISO and M21Si3 ISO Carbon and graphite reinforced PTFE PDR 0.8
5 Seat
M21Vi2 ISO and M21Vi3 ISO Virgin PTFE

6 Insert 'O' ring EPDM Geothermal

9 Stem seal Antistatic R-PTFE

10 Stem seal Stainless steel AISI 304

13 Separator Zinc plated carbon steel SAE 1010

14 Belleville washer Stainless steel AISI 301

15 Gland nut Zinc plated carbon steel SAE 1010 / SAE 12L14

16 Upper steam nut Zinc plated carbon steel SAE 1010 / SAE 12L14

17 Locking plate Stainless steel AISI 304

18 Nameplate Stainless steel AISI 430

20 Lever Zinc plated carbon steel SAE 1010

21 Grip Vinyl

25 Stop screw Zinc plated carbon steel SAE 12L14

26 Split lock washer Stainless steel AISI 304

TI-P133-77 ST Issue 4 Page 3 of 7

M21Si ISO and M21Vi ISO Reduced Bore Ball Valves DN15 to DN150 Flanged PN40
DN65 DN80 to DN150
27 20 21

27
23

24
22
20
17 29
15
28 17
14
15
19
13 14
12 13
25 8
11
DN65 to DN150

31

32

1 18 7 5 3 5 7 6 2

Materials
No. Part Material
M21Si2 ISO and M21Vi2 ISO Zinc plated carbon steel ASTM A216 WCB
1 Body
M21Si3 ISO and M21Vi3 ISO Stainless steel ASTM A351 CF8M
M21Si2 ISO and M21Vi2 ISO Zinc plated carbon steel SAE 1040
2 Insert
M21Si3 ISO and M21Vi3 ISO Stainless steel AISI 316
3 Ball Stainless steel AISI 316
4 Stem Stainless steel AISI 316 / AISI 420
M21Si2 ISO and M21Si3 ISO Carbon and graphite reinforced PTFE PDR 0.8
5 Seat
M21Vi2 ISO and M21Vi3 ISO Virgin PTFE
6 Insert 'O' ring EPDM Geothermal
7 Seat 'O' ring EPDM Geothermal
8 Stem 'O' ring EPDM Geothermal
11 Lower stem seal Antistatic R-PTFE
12 Upper stem packing Virgin PTFE
13 Separator Zinc plated carbon steel SAE 1010
14 Belleville washer Carbon steel/stainless steel
15 Gland nut Zinc plated carbon steel SAE 1010 / SAE 12L14
17 Locking plate Stainless steel AISI 304
18 Nameplate Stainless steel AISI 430
19 Stop plate with indicator DN65 only Zinc plated carbon steel SAE 1010
20 Lever Zinc plated carbon steel SAE 1010
21 Grip Vinyl
22 Adaptor Zinc plated SG iron
23 Adaptor plate Zinc plated carbon steel SAE 1010
24 Adaptor with indicator DN80 to DN150 Zinc plated SG iron
25 Stop screw DN80 to DN150 Zinc plated carbon steel SAE 12L14
27 Adaptor screw Zinc plated carbon steel Grade 5
28 Stop screw DN80 to DN150 Carbon steel
29 Adaptor hex. nut DN80 to DN150 Zinc plated carbon steel
31 Antistatic device ball Stainless steel AISI 302
32 Antistatic device spring Stainless steel AISI 301

Page 4 of 7 TI-P133-77 ST Issue 4

M21Si ISO and M21Vi ISO Reduced Bore Ball Valves DN15 to DN150 Flanged PN40
Dimensions/weights (approximate) in mm and kg
PN40 DIN 3202 F4 flanges PN40 BS 2080 flanges
Size A B C D E F Weight Size A B C D E F Weight
DN15 115 57 162 95 95 13 2.5 DN15 - - - - - - -
DN20 120 60 162 105 95 13 3.2 DN20 - - - - - - -
DN25 125 62 162 115 101 19 4.0 DN25 165 62 162 115 101 19 4.2
DN32 130 65 182 140 106 25 5.5 DN32 178 65 182 140 106 25 5.9
DN40 140 70 186 150 118 30 6.9 DN40 190 70 186 150 118 30 7.4
DN50 150 75 186 165 123 37 9.3 DN50 216 75 186 165 123 37 10.2
DN65 170 79 278 185 144 50 13.4 DN65 241 79 278 185 144 50 14.9
DN80 180 91 417 200 157 57 17.7 DN80 283 91 417 200 157 57 20.2
DN100 190 98 517 235 172 75 25.0 DN100 305 98 517 235 172 75 29.4
DN150 - - - - - - - DN150 403 130 700 300 205 100 56.9

B C B C

E E

ØD ØF Ød ØF

DN15 to DN50 DN65 to DN150

a
a

Kv values
DN 15 20 25 32 40 50 65 80 100 150
Kv 10 10 30 40 81 103 197 248 581 735
For conversion C v (UK) = Kv x 0.963 C v (US) = Kv x 1.156

Operating torque (N m)
DN 15 20 25 32 40 50 65 80 100 150
Nm 8 8 10 15 20 25 50 70 100 155
Note: The torque figures shown are for a valve that is frequently operated at the maximum operating pressure. Valves that are subject to
long static periods, may require a greater break-out torque.

Safety information, installation and maintenance

For full details see the Installation and Maintenance Instructions supplied with the product.
Welding
Only the models that have connections designed for welding (SW, BW, Imperial Tube connections) should be welded. Valves with flanged
connections must not be welded to avoid damages to the valve and/or injury to personnel.

How to order
S = Carbon and graphite reinforced PTFE - PDR 0.8
Model Seat material
V = Virgin PTFE
Specify
2 = Zinc plated carbon steel
Material Body material
3 = Stainless steel
Example: 1 off Spirax Sarco DN50 M21Si2 ISO ball valve having flanged EN 1092 PN40 connections.

Optional extras:
- Self-venting ball.
- Extended stems to allow full insulation: 50 mm (2") for DN15 to DN50 sizes and 100 mm (4") for DN15 to DN150 sizes.
- Lockable handle.
- 100 mm extended stem with lockable handle.

TI-P133-77 ST Issue 4 Page 5 of 7

M21Si ISO and M21Vi ISO Reduced Bore Ball Valves DN15 to DN150 Flanged PN40
DN15 to DN50 - Spare parts (see page 7 for sizes DN65 - DN150)
The spare parts available are shown in solid outline. Parts drawn in a grey line are not supplied as spares.

Available spares
Seats, insert 'O' ring and stem seals 5, 6, 9, 10

How to order spares

Always order spares by using the description given in the column headed 'Available spares' and state the size and type of ball valve.

Example: 1 set of seats, insert 'O' ring and stem seals for a Spirax Sarco DN50 flanged PN40 M21Si2 ball valve.

10

9 9

DN15 to DN50 5 5 6

Page 6 of 7 TI-P133-77 ST Issue 4

M21Si ISO and M21Vi ISO Reduced Bore Ball Valves DN15 to DN150 Flanged PN40
DN65 to DN150 - Spare parts (see page 6 for sizes DN15 - DN50)
The spare parts available are shown in solid outline. Parts drawn in grey line are not supplied as spares.

Available spares
Seats, insert 'O' ring, seat 'O' ring, stem 'O' ring, lower stem seals and upper stem packing 5, 6, 7, 8, 11, 12

How to order spares

Always order spares by using the description given in the column headed 'Available spares' and state the size and type of ball valve.

Example: 1 set of seats, insert 'O' ring, seat 'O' ring, stem 'O' ring, lower stem seals and upper stem packaging for a Spirax Sarco DN80
flanged PN40 M21Si2 ball valve.

12

8
11

DN65 to DN150 7 5 5 7 6

TI-P133-77 ST Issue 4 Page 7 of 7

M21Si ISO and M21Vi ISO Reduced Bore Ball Valves DN15 to DN150 Flanged PN40