Thesis 1995 Tabtiang

Download as pdf or txt
Download as pdf or txt
You are on page 1of 211

This item was submitted to Loughborough University as a PhD thesis by the

author and is made available in the Institutional Repository


(https://dspace.lboro.ac.uk/) under the following Creative Commons Licence
conditions.

For the full text of this licence, please go to:


http://creativecommons.org/licenses/by-nc-nd/2.5/
- - - - - - - - -

LOUGHBOROUGH
UNIVERSITY OF TECHNOLOGY
LIBRARY
AUTHOR/FILING TITLE
._____________ 1"~rLIj~_C:L __Ii_·_____________ _
. ACCESSION/COPY NO.

. ~()ll() 'lC7
----------------- ---- ------- --- ----------- - - --- - --
VOL. NO. CLASS MARK

{f jUN' 1997
27 JUN 1597

0401108074

11111I1 I 111111111111111111111·,
IRRADIATION CROSSLINKING OF ORIENTED PLASTICISED PVC COMPOUNDS

by

ARUNEE TABTIANG

A Doctoral Thesis
submitted in partial fulfilment of the
requirements for the award of
Doctor of Philosophy
of the
Loughborough University of Technology

FEBRUARY 1995

Supervisor: M. Gilbert, Ph.D.

Institute of Polymer Technology


and Materials Engineering

©by Arunee Tabtiang (1995)


Loughborough UnlverrJty
of Tec::,nc:"'~~v Ubrar/ .-.1 "
........... "..., .... ,,-... ~.~ •.•.....-,."'-..-:1

Date J~ cd..
-"'.'~"' .. -... , ·r ... ~

Class
....,,~>,,~ ,...... .........,t..-..,
Ace.
No. 6't () \( 0 ~o7 i
ACKNOWLEDGEMENTS

I would like to express my gratitude to Dr. Marianne Gilbert for her invaluable
guidance and encouragement throughout the course of this project. I am also grateful
to Thai Government for an award of the grant to undertake this study.

My thanks are also due to:


• Smith & Nephew Research Limited and Harcros Chemicals UK Limited for
use of their irradiation facility,
• the staff and colleagues at IPTME and in particular the technicians for all
their help and friendship,
• Dr. D. Hilt for many useful discussions,
• Mr D. Hemsley for his contributions with respect to birefringence

measurement,

Finally, I would like to thank my family and Rukchonlatee's family for all their
support, and to Rich for the sacrifices he has made during the writing of this thesis.
SYNOPSIS

Plasticised polyvinyl chloride (PPVC) compounds were biaxially stretched,


annealed in the drawn state and subsequently exposed to electron beam irradiation.
During sample irradiation the crosslinking reaction was promoted by a radiation
sensitising monomer, trimethylolpropanetrimethacrylate (TMPTMA), included in the
PVC compound formulations. The influence of stabiliser type and level, TMPTMA
level and irradiation dose on the network structure produced was investigated. A tin
stabiliser, Stanclere TL, was selected for this study as it promoted the crosslinking
reaction and it showed no interfering peaks in the wide angle x-ray diffraction
(WAXD) traces which were used to follow the development of structural order. The
appearance of gel, the material insoluble in THF, in irradiated oriented samples proved
that a crosslinked structure was created. The gel formation increased with TMPTMA
level and irradiation dose. The gel content was found to affect mechanical properties at
elevated temperatures and produced an increase in the area shrinkage temperature.
Sample thickness and the plasticiser content were found to have a major effect upon
gel formation. The thicker the sample was, the smaller the quantity of gel that was
formed. Samples containing 46.5phr plasticiser showed greater gel content than
samples containing 25phr plasticiser as a result of the higher molecular mobility in the
more plasticised samples. It was also found that the orientation of the film decreased
the efficiency of network formation in PVC formulations with a 46.5phr plasticiser
content but no significant change in gel content could be detected in those containing
25phr plasticiser.

Tensile properties and impact strength at room temperature were slightly

improved in irradiated samples. The modified structure resulted in an improvement in


tensile strength and penetration resistance at higher temperatures and an increased area

shrinkage temperature. Crosslinking did not affect room temperature recovery or


J..
crystalline orientation; however irradiation crosslinking reduc~s crystallinity. 'i
TABLE OF CONTENTS

Page
CHAPTER 1
INTRODUCfION .......................................................................................................... 1
1.1 General...................................................................................................... 1
1.2 Morphology of PVC .................................................................................. 4
1.3 Fusion of PVC ........................................................................................... 6
1.4 Crystallinity ................................................................................................ 8
1.5 Molecular Orientation ................................................................................ 14
1.6 Techniques to Investigate Orientation in PVC ............................................ 19
1.6.1 Birefringence ........................................... .................................... 21
1.6.2 X-ray Diffraction(XRD) ...................................................... ........ 23
1.6.3 IR Spectroscopy ............................................................... .......... 25
1.6.4 Raman Spectroscopy ................................................................... 27
1.6.5 Fluorescence Spectroscopy ...................................................... .... 27
1.6.6 Nuclear Magnetic Resonance (NMR) ..................................... ...... 28
1. 7 Effect ofIrradiation on PVC ...................................................................... 28
1.8 Effect of Crosslinking on PVC .......................................................... ......... 34
1.9 Effect of Orientation on PVC ................................................... .................. 37
1.10 Aims of This Project... ................................................ .............................. 39

CHAPTER 2
EXPERIl\fENrAL PROCEDUREs ................................................................................... 42
2.1 Materials ........................................................................................... ......... 42
2.1.1 Polyvinyl ChIoride(pVC) ............................................................. 42
2.1.2 Trimethylol Propane Trimethacrylate(TMPTMA) .. ................. ..... 43
2.1.3 Stabilisers ................................................................................ .... 43
2.1.4 Plasticiser and Lubricant .. .................................................... ........ 43
2.2 Sample Preparation ..................... ............................................................... 44
2.2.1 Formulations .......................................................................... ..... 44
2.2.2 Dry blending .............................................. ................................ 45
2.2.3 Milling ................................................................................ ......... 45
2.2.4 Compression moulding ................................................................ 47
2.2.5 Biaxial Stretching ........................................................... ............. 48
2.2.6 Irradiation.................................................................................... 52
2.3 Characterisation and Testing ...................................................................... 52
2.3.1 Assessment of Crosslinked Structure ........................................... 52
2.3.1.1 Percentage Gel Content ................................................. 52
2.3.1.2 Crosslink Density Measurements ................................... 53
2.3.2 Mechanical Properties.................................................................. 53
2.3.2.1 Tensile properties .......................................................... 53
2.3.2.2 Impact Testing .............................................................. 54
2.3.3 Thermal Analysis ......................................................................... 54
2.3.3.1 Differential Thermal Analysis ........................................ 54
2.3.3.2 Thermomechanical Analysis (TMA) .............................. 54
2.3.3.2.1 Softening Temperature ............................................... 54
2.3.3.2.2 Shrinkage Measurement ............................................. 55
2.3.4 X-ray Diffiaction Measurement ................................................... 58
2.3.5 Birefiingence ............................................................................... 59
2.3.6 Density Measurement .................................................................. 63
2.3.6 Ageing Study ............................................................................... 63

CHAPTER 3
RESULTS AND DISCUSSION
I. PRELll\UN"ARY INVESTIGATION .............................................................................. 64
3.1 Introduction ............................................................................................... 64
3.2 Effect of Temperature on Percentage Elongation at Break .......................... 65
3.3 Percentage Gel Content... ........................................................................... 65
3.4 Thermomechanical Analysis ....................................................................... 67
3.4.1 Softening Temperature ................................................................ 67
3.4.2 Shrinkage· .................................................................................... 69
3.5 Tensile properties ....................................................................................... 69
3.6 Wide Angle X-ray Diffraction (WAXD) ..................................................... 71
3.7 Conc1usion ................................................................................................. 71

CHAPTER 4
RESULTS AND DISCUSSION
IT SELECTION OF A SUITABLE FORMULATION AND CROSSLINKING CONDITIONS.-.u 74
4.1 Introduction ............................................................................................... 74
4.2 Effect of Stabiliser ...................................................................................... 75
4.2.1 Percentage Gel Content ............................................................... 76
4.2.2 Softening Temperature ................................................................ 80
4.2.3 Ageing properties ........................................................................ 82
4.2.4 Wide Angle X-ray Diffraction ...................................................... 84
4.2.5 The Preferred Stabiliser for this Study .......................................... 89
4.3 Effect of Stabiliser Content ........................................................................ 89
4.3.1 Percentage Gel Content and Crosslink Density............................. 90
4.3.2 Thermomechanical Analysis ......................................................... 92
4.3.3 Tensile Properties .................................... : ................................... 92
4.4 Effect ofTMPTMA LeveL ....................................................................... 96
4.4.1 Percentage Gel Content and Crosslink Density............................. 96
4.4.2 Thermomechanical Analysis ......................................................... 98
4.4.3 Tensile Properties ........................................................................ 101
4.4.4 The selection ofTMPTMALevel ................................................ 104
4.5 Effect ofIrradiation Dose ........................................................................... 104
4.5.1 Percentage Gel Content and Crosslink Density ............................. 105
4.5.2 Thermomechanical Analysis ......................................................... 106
4.5.3 Tensile properties......... ........ ............. ... ....................................... 108
4.6 Study of Oriented Samples ......................................................................... 110
4.7 Conclusion ................................................................................................. 113

CHAPTERS
RESULTS AND DISCUSSION
III PROPERTIES OF CROSSLINKED ORIENTED SAMPLES ........................................... 114
5.1 Introduction ............................................................................................... 114
5.2 Effect of Sample Thickness ........................................................................ 114
5.2.1. Percentage gel content ................................................................ 116
5.2.2. Tensile properties ....................................................................... 117
5.2.3. Selection of Sample Thickness .................................................... 118
5.3 Effect of Draw Ratio .................................................................................. 118
5.3.1. Percentage gel content................................................................ 120
5.3.2 Tensile Properties ........................................................................ 121
5.3.3. Impact Properties ....................................................................... 130
5.4 Effect of Annealing Temperature ................................................................ 134
5.4.1 Percentage Gel Content ............................................................... 134
5.4.2. Tensile Properties ....................................................................... 135
5.5 Conclusions ............................................................................................... 137
ClIAPTER6
RESULTS AND DISCUSSION
IV CHARACTERISATION............................................................................................. 138
6.1 Introduction .............................................................................................. 138
6.2 Crystallinity Measurements......................................................................... 138
6.2.1 Differential Thermal Analysis ....................................................... 138
6.2.2 Density Measurement .................................................................. 146
6.3 Measurement ofBirefiingence .................................................................... 147
6.4 Crystalline Orientation................................................................................ 150
6.4.1 Wide Angle X-ray Diffraction (WAXD) ....................................... ISO
6.4.2 X-Ray Diffraction Photograph ..................................................... 154
6.5 Shrinkage measurements ............................................................................ 156
6.5.1 Thermal Shrinkage....................................................................... 160
6.5.1.1 Effect of Draw Ratio ................................................................ 160
6.5.1.2 Effect of Gel Content ................................................................ 165
6.5.1.3 Annealing Temperature ............................................................. 165
6.5.2 Room Temperature Recovery Rate .............................................. 168
6.6 Summary of the Relationship Between Structure and Properties ................. 170
6.6.1 Effect of Orientation .................................................................... 170
6.6.2 Effect ofIrradiation Crosslinking ................................................. 172
6.6.3 Conclusions ................................................................................. 175

CHAPTER 7
GENERAL CONCLUSIONS AND SUGGESTIONS FOR FURTHER STUDy.......................... 177
7.1 General Conclusions................................................................................... 177
7.2 Suggestions for Further Study .................................................................... 179

REFERENCES .............................................................................................................. 181

APPENDIX ................................................................................................................... 189


Chapter 1 Introduction 1

CHAPTER 1

INTRODUCTION

1.1 GENERAL

The repeat unit of the PVC polymer chain is [-CH2-CHCI-]. The polar groups
in the molecule give rise to strong intermolecular bonds which join adjacent polymer
chains rigidly together. Therefore, PVC is a stiff and inflexible material. The use of

plasticiser converts the inherently hard PVC polymer into compositions with varying
degrees of softness and flexibility, which are processable into a variety of products

with diverse properties and uses. A plasticiser is a substance of low or negligible


volatility, suitably compatible with the polymer into which it is incorporated. The

significant consequences of plasticisation are the lowering of the glass transition


temperature(Tg), softening temperature, reduction of strength and increased impact

resistance.

PVC plasticisers are mainly organic esters with high boiling points. About two-
thirds ofthe plasticisers in general use are diesters of phthalic anhydride with C4-CIO

alcohols. Examples of plasticisers in this group are dioctylphthalate(DOP), di-


isooctylphthalate(DIOP), di-isodecylphthalate (DIDP), etc. The other classes of more

specialised plasticisers are triaryl phosphates, alkyl esters of dibasic alkyl acids, alkyl
trimellitate esters, high-molecular-weight polyesters and epoxies. The important

parameters for selecting the plasticiser for each system are:

1. compatibility and ease of mixing with the PVC polymer


2. effectiveness in producing the softness and flexibility of plasticised PVC

3. permanence
Chapter 1 Introduction 2

Dehydrochlorination is the initial step in the degradation of PVC when it is

exposed to heat and mechanical shearing in the course of processing, or during service

when the material experiences heat or ultraviolet light. The main products of this

reaction are hydrogen chloride, as a toxic and corrosive gas, and polyene structures.

The presence of degradation products in PVC components dramatically reduces their

mechanical and electrical performance. The evolution of hydrogen chloride gas is

obviously harmful to both machinery and those who operate it. The polyene structures

produce colour in PVC materials containing degraded products, due to the absorption

of light by the double bonds present within the polyenes. The decomposition process

can be inhibited by the incorporation of stabilisers. Some reactions performed by

stabilisers are summarised(l-2):

- Reaction with hydrogen chloride. It is important to remove hydrogen chloride

from the system as it further catalyses thermal degradation(3).

- Reaction with allylic chlorides to stop further dehydrochlorination.

- Reaction with double bonds in polyene structures.

- Free radical absorption, since the degradation process proceeds by a radical

path.

The stabiliser is thus, next to the polymer, the second most important

constituent of every PVC composition. The compounds used as heat stabilisers for

PVC may be divided (by chemical type) into the following general groups.

1. lead compounds

2. organotin compounds

3. compounds of other metals

4. organic stabilisers

The way of selecting a stabiliser or mixture of stabilisers depends on the application of


Chapter 1 Introduction 3

the final product and manufacturing costs.

Besides stabiliser and plasticiser, other components are often included in PVC

formulation, mainly for easier processing and particular end-use properties. An external

lubricant, e.g. stearic acid, counteracts sticking of the melt to hot equipment surfaces

in processing. An internal lubricant, e.g. calcium stearate, reduces frictional effects

between PVC grains. A processing aid is included to improve melt properties and

fusion characteristics. An impact modifier is incorporated in the composition to impart

toughness to the relatively brittle PVC polymer. Fillers are often incorporated as

cheapening extenders, but in some cases the attendant effects on some properties may

be useful, e.g. reduced shrinkage, increased hardness and stiffness.

PVC is well-known for its excellent properties such as good insulation, heat

and fire resistance, high mechanical strength, toughness and formulation versatility and

has been proved to be cost-effective for a wide variety of uses, for example cable

insulation, sheathing and plastic pipe systems. However, this material presents some

problems. The use of PVC may be limited, by its performance at higher pressures and

temperatures. It has a tendency to flow and to have a reduced mechanical strength at

elevated temperatures and it also lacks abrasion resistance. Ways to improve the

properties of PVC have been extensively studied and crosslinking has been one of the

methods used. Crosslinked PPVC shows an increased softening point, over PPVC,

leading to a raising in its maximum service temperature.

When PVC is stretched and annealed, molecular orientation occurs and can

strongly influence the properties of the system. The large change in properties on

orientation is due to both crystalline and amorphous orientation. However, oriented

PVC is not suitable for use at high temperature, due to its shrinkage.
Chapter 1 Introduction 4

1.2 MORPHOLOGY OF PVC

The morphology of PVC has been extensively studied. It was found that

morphology is responsible for the physical property characteristics of the polymer. The

morphology of a grain of PVC considerably affects the ability of the particulate

polymer to absorb plasticiser. The morphology depends on many factors, including the

ways of producing PVC resins(4). The four commercial processes are suspension, bulk,

emulsion and solution polymerisation, but approximately 80% of PVC is produced by

suspension polymerisation. PVC resins or grains prepared by this process are known to

consist of irregularly shaped, porous granules of the order of 100 ~m in diameter.

During suspension polymerisation, the first species formed are macro radical

coils which aggregate rapidly to produce micro domains or basic particles. This species

is unstable and aggregates to form domains. The domains also aggregate and form

primary particles which continue to grow at the expense of the monomer to give

grains of PVC approximately 150 ~m in diameter<S). The simple representative of this

mechanism was published by Allsopp(6) as shown in Figure 1.1.

A number of investigators have tried to observe the micro domains by using a

variety of techniques. Rattori et al. (7) have studied the particle formation of suspension

PVC by using electron microscopy. Approximately spherical 0.1 ~m diameter particles

were seen in the 10 ~m diameter grains while the polymerisation reaction was in

progress. They also observed that the 1 ~m primary particles were broken down to

form fibrils IO-30nm in thickness during powder extrusion. Their diagram of PVC

powder morphology is shown in Figure 1.2. Neilson and Jabarin(8) and Wenig(9)

revealed the existence of microdomains in unplasticised PVC (UPVC) using smalI-

angle- x-ray scattering.


Chapter 1 Introduction 5

SIZE CONVERSION

Coiled macro <1%


radicm

Micro domains
U lrun

t
(i\
Domains U 1G-3Orun
1-2%

1
Prlmaryparticles o 0.2-1.5um

1
Primary particle
aggregates
CflJO 1-2um
4-10%

t
PVC grain ~
V 65-15Oum
90%

Figure 1.1 Scheme for polymer precipitation inside vinyl chloride droplets
during polymerisation

particle
Conoidal skin

65-15Oum

Figure 1.2 PVC particle morphology


Chapter 1 Introduction 6

This composition of a PVC grain was also supported by determining the


temperature torque profile of a PVC compound in a Brabender Plasticorder mixing
chamber<lO) . Three characteristic peaks in the torque temperature trace were found

and it is suggested that these peaks are associated with the breaking down of the PVC

powder particles, microgranules, and primary particles.

1.3 FUSION OF PVC

PVC products are produced by blending PVC powder with the necessary

additives in a high speed mixer and followed by processing by an appropriate method


e.g. compression moulding or extrusion. During processing, gelation or fusion, in

which the powder grains are broken down to produce a continuous network, takes
place. The fusion process is highly dependent on both shear and thermal history of the

polymer. The fusion behaviour of grains is governed by the processing method, and
also by the additives which are normally initially present at the grain surfaces. It has

been suggested that the distribution of the additive on the powder influences grain
fusion(ll) . Allsopp(12) has suggested two routes for grain and primary particle fusion.

The overall view of fusion, by Gilbert et al.(ll) , postulating a melting and

recrystallising process leading to network formation at the later stages of the process is

shown in Figure 1.3.

The level of fusion is an important factor in determining the mechanical


strength and fracture behaviour of processed products, therefore, various methods for

assessment of fusion have been developed.


Chapter 1 Introduction 7

High shear

Shear

Final network

Figure 1.3 Fusion mechanisms

Tensile properties can be used to indicate fusion level, since the greater the

fusion, the higher the tensile strength. In this test, a specified form of a large amount of

sample is required, so it is not suitable for quality control process.

In solvent immersion tests for assessing fusion levels, processed PVC samples

were immersed in a fairly compatible solvent, such as acetone or methylene chloride.

This test is very convenient but it cannot be used to distinguish samples possessing a

fusion level over about 70%(13).

A rheological method for assessment of fusion was developed by Gonze(l4) and


Lamberty<IS) and is used by a number of workers(II,16,17). In this method, the capillary

entrance pressure loss is measured while samples of varying states of fusion are

extruded through a zero length die at a temperature below that of the processing
Chapter 1 Introduction 8

temperature. By plotting capillary rheometry extrusion pressure against processing

temperature, it is possible to produce a standard fusion curve.

Gilbert and Vyvoda(18) used a thermal analysis technique for investigating

gelation of rigid PVC components. They suggested that the area of the broad

endotherm ranging from about \10°C to the maximum processing temperature in the

thermogram appears to be related to the level of fusion since the energy of this

endotherm arises from the breakdown of less ordered structures produced during

cooling after processing. This suggestion was supported by Isles and Delatycki(19) who

used DSC to follow the changes within the microdomains due to processing.

1.4 CRYSTALLINITY

Crystallinity in PVC can be divided into two types: primary crystallinity and

secondary crystallinity<20). Primary crystallinity is of relatively high order, occurring in

virgin powder and single crystals prepared with special care. It is destroyed by heat

during processing, while secondary crystallinity forms on subsequent cooling. This

secondary crystallinity creates a network on fusion or gelation. Many workers(17·20.21)

have proved that recrystallisation or secondary crysta\lisation from a PVC melt

produces a less ordered structure than the primary crysta\1inity. This results in a lower

melting temperature, a lower heat of fusion and higher solvent sorption(21).

Natta and Corradini(22) were the pioneers who investigated the structure of

crystalline PVC by using wide angle x-ray diffiaction(WAXD). Using oriented fibres of

PVC, prepared with the aid of free radical catalysts, they found the crystal structure to

be orthorhombic with unit cell dimensions a= IO.4A, b= s.3A and c= S.IA. This

structure has been supported by Wilkes et al. (23) studying oriented mats of single
Chapter 1 Introduction 9

crystals with w'AXD. Their results showed that the orthorhombic crystal unit cell is
more compact than that of Natta and Corradini with the dimensions a= 1O.24A, b=

S.24A and c= s.osA.

Mammi and Nardi(24,2S) studied the x-ray diffraction pattern of oriented and

unoriented PVC samples. They have found that some reflections cannot be ascribed to

the orthorhombic crystal form. They attributed these reflections to the so called

mesomorphic or nematic structures which appear after annealing stretched fibres at 87-

107°C. These nematic structures consist of straight chains aligned in parallel with a

distance between the axes of S.4A. The reflection from nematic structures of PVC was

also found by Lebedev et al. (26) after annealing at a temperature above the glass

transition temperature. Another work of Lebedey(27) showed that samples annealed at

110°C produced the reflections from orthorhombic and nematic structures at the same

time, which means that the alignment of chains proceeds simultaneously with the

formation of real orthorhombic crysta11ites.

In PVC, it is possible for the chloride atom to have two different arrangements

about the polymer chain backbone. Consider the case where all the chlorine atom are

found in the same relative position; the resulting structure is known as an isotactic

chain.

H H H
I I I
-CH -C-CH -C-CH2- C -
2 I 2 I I
a a a
isotactic

If, on the other hand, the .atoms are in alternating configuration, a syndiotactic chain is
Chapter 1 Introduction 10

fonned.

H a H
I I I
-CH -C-CH -C-CH2-C-
2 I 2 I I
a H a
syndiotactic

A third possibility is where the chlorine atoms are positioned randomly, hence the

structure is tenned atactic.

It was found that PVC with a very high proportion of the syndiotactic structure

was highly crystalline, and showed higher melting temperatures than those of atactic

PVC grades(20) . This has led to the idea that only the syndiotactic parts in the PVC

chains are able to fonn crystallites. However, commercial PVC have a tacticity of

about 55% which means that the polymer is almost atactic but some crystallisation can

occur.

Juijn et al. (28) studied crystallinity in atactic PVC and said that the crystalline

phenomenon in PVC cannot be explained by assuming that only the syndiotactic chain

segments crystallise. Consequently, some isotactic chain segments must be able to

crystallise. Another reason to support this idea is that the orthorhombic crystal form is
independent oftacticity of the PVC: Nattaand Corradini(22), Smith and Wilkes(29) and

Nakajima and Hayashi(3O) studied atactic PVC, syndiotactic PVC and a combination of

syndiotactic and atactic PVC, respectively, but they all found the orthorhombic lattice.

However, the model of Juijn et al. is similar to that ofNatta and Corradini except that

the isotactic chain fits perfectly in the orthorhombic cell, surrounded by syndiotactic

chains. (Figures 1. 4-1. 7)


Chapter 1 Introduction 11

Recently, Hobson and Windle(31.32) have studied x-ray diffraction patterns of

PVC with varying sample tacticity and identified a crystal structure in which both

isotactic and syndiotactic sequences are incorporated within the same lattice. They

presented a short summary of molecular and diffraction modelling results which show

the effect of crystalline tacticity on the intensities of the 200 and 110 peaks.

The tacticity depends very strongly on polymerisation techniques. Highly

syndiotactic PVC is obtained by polymerisation in the presence of butyraldehyde(33)

and irradiating the urea inclusion complex of vinyl chloride at _78°C(34). For the

emulsion and suspension processes, the commercially important polymerisation

techniques, the polymerisation temperature is the most important factor influencing the

tacticity . of the polymer. However, the crystallinity is not controlled only by the

tacticity but also by the mechanical and thermal history of the PVC. For example,

stretching increases the crystallinity of the material.

Commercial PVC is considered to contain about 55% of syndiotactic diads(35).

X-ray diffraction has indicated that the level of crystallinity in UPVC is of the order of
10%(9,36-40). In 60 phr PPVC, the crystallinity was found to be reduced to about 4%(39).

By DSC measurement, the PVC formulations containing 20-30% by weight of

plasticiser was determined to have a crystallinity value of the order of 7-8%(40),

therefore both UPVC and PPVC are known to be semicrystalline polymers. This

semicrystallinity is accepted to be a three-dimension network structure in which the


small crystallites act as crosslinkS(4O-%) (Figure 1.8).
Chapter 1 Introduction 12
, ,

··_··m l
"'\
'.
-o_m)
.;,'
-m

,
b
J
b

\, ./
.,....... I '- ..... . ~/
b i. b

Figure 1.4 Model of the orthorhombic structure ofpolyvinylchloride

/sotactic
Syndiotactic

Figure 1.5 Comparison of the syndiotactic and isotactic straight chains.


Longitudinal section
Chapter 1 Introduction 13

Syndiolaclic /solaclic

Figure 1.6 Comparison of the syndiotactic and isotactic straight chains


Cross-section
c

\.
·_···m

./
./
,."
j
.,\\

--m

/
/,
,,
/
'\,

!
c c C

b
b ,
b

Figure 1.7 Model of the structure of pvc Combination ofsyndiotactic and

isotactic chains segments in the orthorhombic lattice


Chapter 1 Introduction 14

Crystallit8

Figure 1.8 Semicrystalline structure

1.5 MOLECULAR ORIENTATION

Molecular orientation in a solid polymer may have a profound influence on the

macroscopic physical properties of the polymer. Polymer fibres and films are the

important commercial products, with their strength resulting from oriented crystal

morphology, brought about by stretching and the subsequent crystallisation processes.

Nowadays, this process is used not only in fibres and films but also in many application

areas, for instance, pipe and stretch blow moulded bottles. However, orientation can

be disadvantageous because it causes mechanical and optical properties to be

anisotropic i. e. different properties in different directions. The biggest problem area is

the undesirable orientation occurring during injection moulding and leading to

anisotropy. As a result, the products have dimensional instability and poor mechanical

properties.

Previous research on stress-induced crystallisation of polymer networks has


been carried out by a number of workei<47.S7). KatZ<47-48), using x-ray diffraction, was

among the first to investigate crystallite orientation and size in rubber-like synthetic

substances which crystallise when stretched. Sometime later F10ry(49) evaluated the first
Chapter 1 Introduction 15

thermodynamic treatment of polymer crystallisation induced by stretching, which

included two topics. Firstly, the strain over and above the isotropic equilibrium melting

point causes melting point elevation. Secondly, he discussed the relationship between

the increase in degree of crystallinity at constant elongation and temperature and the

relative decrease in stress at crystallisation equilibrium with elongation and

temperature. The latter relation was based on the assumption that crystallisation

(nucleation and growth) at constant elongation occurred along the strain direction,

suggesting the following: a) that the strain-induced nuclei had a fringed-micelle chain

conformation, and b) that the resultant crystallites due to strain-induced crystallisation

and/or additional thermally-induced crystallisation had dimensions comparatively

greater in the strain than in the transverse directions. Such deduction about chain

conformation and crystal dimensions from non-structural studies should be viewed

with caution, especially since the deductions are based on an assumed crystal growth

mechanism and direction that was shown to be wrong(SO). Nevertheless, these

deductions seemed rather reasonable based on what was known at the time about

polymer morphology, especially if it was assumed that the starting amorphous

polymer had a random coil chain conformation. Stretching would be expected to

extend and orient the randomly coiled macromolecules in the stretch direction. Upon

phase transition, the aligned neighbouring segments would be expected to lead directly

to crystallites with a fringed-micelle chain conformation that is not so different from

the as-stretched chain conformation. Any crystal growth would also be expected to

continue along the stretch direction rather than perpendicular to it.

Gent(SI) carried out a series of experiments including simultaneous volume and

stress relaxation measurement from several polymers that were crystallised under strain

at temperatures below their isotropic melting point. He concluded from the results that

the crystal melting temperature which increased with the imposed extension, showed a
Chapter 1 Introduction 16

good agreement with Flory's treatment of oriented crystallisation.

Jude and Stein<l2) studied axial length changes at constant load during

crystallisation of crosslinked polyethylene from the melt. The results showed that the

measured length always increased initially, but contracted later, espectially at small

loads, and eventually levelled off at long times. It was concluded that the increase in

length is caused by a change in chain conformation to fringed micelles, followed by

contraction due to chain folding during oriented crystallisation. This result was also

supported by Keller and Machin(53) who proposed a two step mechanism for formation

of row-oriented lamellae, the first step resulting in an increase in the axial length began

with strain-induced longitudinal nucleation of extended-chain crystals which they

suggested occurred in the initial period and the second step followed with a thermally-

induced lateral growth of chain-folded crystals, during which the length contractions

took place. In addition, their study with wide angle x-ray scattering gave a good

agreement with their proposal, consequently annealing at high temperature after

stretching contributes to lateral alignment so that the original fibrillar morphology

finally disappears and changes to an apparent lamellar type "row morphology", a

nematic mesomorphous phase.

This two step mechanism was also supported by Yeh and Lambert(54) and Yeh

and Geil<5l) studying isotactic polystyrene and polyethylene-terephthalate, respectively.

Furthermore, they have found that the transformation from a fibrillar morphology to a

lamellar morphology can be either irreversible or reversible (leading to shrinkage),

depending upon the temperature of the stretching and annealing processes. Another

work ofYeh<l6-l7) reported that the resulting morphology was very dependent upon the

annealing conditions e.g. whether the specimens were free or restrained while

annealing took place, and the magnitude of applied strain.


Chapter 1 Introduction 17

PVC is one of the polymers whose properties can be improved by orientation

crystallisation. This polymer as produced contains 5-10% crystallinity but this value

can be increased by many techniques(36,40,58-64) e.g. drawing and annealing. The

annealed highly syndiotactic sample made by the urea clathrate method gave the

highest value of 76-78% crystallinity(61).

Illers(65) studied the influence of annealing on the physical state of technical

PVC by calorimetric measurements, suggesting that heat treatment above Tg causes

crystallisation and below Tg causes a decrease in free volume. Crystallinity changes

were shown to have a greater effect on density, solvent sorption and shear modulus

than free volume changes.

Molecular orientation behaviour of uniaxially stretched PVC was studied by

several investigators(60-61,63,66-70) . For UPVC, tensile properties increased in the draw

direction and decreased perpendicular to draw, resulting from the development of two-

dimensional order. Annealing caused further changes in the structure, leading to the

improvement of properties. Vyvoda et al. (60) found that the maximum 2-dimensional

order for UPVC occurs on annealing at 110°C. Plasticised polyviny1chloride (PPVC),

having its Tg below room temperature, shrinks considerably after stretching. This

shrinkage can be reduced by annealing in the stretched state because the ordered

structures which hold the oriented chains in position behave as physical crosslinks in

the system.

Improved tensile strength in both directions can be achieved by biaxial

orientation. Brady(58) assessed the influence of all the primary processing variables in

the biaxial orientation process (temperature, rate and degree of extension) upon the

tensile, dynamic mechanical and dielectric properties of non-impact modified PVC. In


Chapter 1 Introduction 18

the same year, de Vries and Bonnebat(59) studied uniaxial and biaxial stretching of PVC

and chlorinated PVC sheet with a view to their behaviour in thermoforming process.

Optimum forming condition were identified and the effect of biaxial orientation on
various properties was also reported. Meijering et al.<71) have demonstrated the
benefits of biaxial orientation particularly for properties relevant in gas pipe

application.

Robinson et al.<7l) compared the results from birefringence measurements of

oriented plasticised PVC compounds with those of many workers(66.69.7l-74) and

showed that an increase in plasticiser content or draw temperature produces a lowering

of the birefringence for a given draw ratio.

Recently, Gilbert and Liu(63-64) studied the effect of uniaxial and biaxial

orientation on UPVC and PPVC structure and properties. They found results similar to .

previous researchers. Furthermore, they found that in biaxial orientation the increase of

two-dimensional order with draw ratio was much less than that observed after uniaxial

orientation and that the amount of ordering is restricted by plasticiser molecules. They

also proposed a model to describe the influence of uniaxial and biaxial orientation on

the structure ofUPVC and PPVC compounds. (Figure \.9)

It can be concluded that in PVC, chain alignment induces crystallisation which

further modifies properties and oriented PVC behaves like a much more crystalline
polymer(64) .
Chapter 1 Introduction 19

MONOAXIAL BIAXIA L

UPVC PPVC PPVC UPVC

Figure 1. 9 Schematic diagram showing effect of drawing. • =plasticiser

1.6 TECHNIQUES TO INVESTIGATE ORIENTATION IN PVC

The techniques used to evaluate molecular orientation give data for the

orientation function in relation to the mathematical definition of orientation. Therefore,

it is important to know how to explain these functions.

The orientation of the chain in the uniaxially oriented polymer is specified by

the angle e between a particular direction in the polymer specimen, such as the

direction of draw, and the molecular chain axis. The quantity, used as a measure of the

distribution of the orientations, will be some function of this angle. For reasons of

mathematical convenience it is sometimes preferable to express the results of studies of

orientation in terms of the average values of the Lagendre polynomials PI(cos9), where

PO(cos9)=1

P2(COS 9) = (3cos29 - 1)/2

P4(COS 9) = (3 - 30cos29 + 35cos49 )/8


Chapter 1 Introduction 20

The biaxial orientation is defined in terms of angles ~ I and <1>2 between the
polymer chain axis and the machine I and transverse 2 direction. The orientation

factors based on the ~I and ~2 system are according to White and Spruiell(75) :

tBI = 2cos2~1 + cos2~2 - I

tB2 = 2cos2~2 + cos 2<1>I - I

For the case of isotropy, tBI and tB2 are zero. For polymer chains perpendicular to

the 12 plane, tBI and tB2 are both -1. For equal biaxial orientation, tBI and tB2 are

equal.

It is possible to graphically present the state of biaxial orientation through a

plot of tBI and tB 2 . All possible states of orientation lie with in an isosceles triangle

with vertex at (-1,-1) and base stretching from (\,0) to (0, \) (Fig. \.10).

Equal biaxial
.. ~--

/;'UnlaxiaJ
(transwr.r. dtnct/on)

Isotropic

Figure 1.10 Orientation triangle

Techniques used to study orientation are shown in Table 1.1 (76). Each

technique has its own limitations and different advantages. Therefore, different

techniques are used to explain aspects of PVC orientation.


Chapter 1 Introduction 21

1.6.1 Birefringence

The measurement of birefringence is the most common method of

characterising polymer orientation. In this technique, the difference between the

refractive indices along two perpendicular directions is measured with polarised light

along these directions. It results from anisotropic optical properties of an oriented

molecule. This technique measures mean values over all the components and phases

present, the details about distribution of orientation cannot be achieved by this


technique. However, it has been used by a number of investigators(63,7o,72,77.79) to study

orientation in PVC. It was found that the value of (dn)in plane increases with draw
ratio. By using this technique, Hibi et a1.(66) found that samples drawn above and below

Tg have different molecular orientations for the same draw ratio because they gave

different values of birefringence.

Kotnis and Spruiell(80) used birefringence to study biaxially oriented films

prepared from PVC/poly(methyl methacrylate co imide)(pI) blends. They chose a co-

ordinate system for the film in which the Z axis was parallel to the first stretch

direction and the Y axis was parallel to the second stretch direction, whilst the X axis

was normal to the plane of the film. All of the biaxially oriented films had

~Zy=O

indicating equal biaxial orientation with respect to the second stretch direction. They

followed the level of orientation developed in the film by measuring the out-of-plane

birefringence, ~z:x: The results showed increasing birefringence with draw ratio for

each blend and with PI content in the blends. The rising of birefringence with draw

ratio can be clearly ascribed to increasing molecular orientation.


Chapter 1 Introduction 22

Table 1. ](76)

Methods for studying orientation in polymers

METHOD PART OF STRUCTURE ORIENTATION EXPERIMENTAL


BEING AVERAGES LIMITATION
CHARACTERISED OBTAINED

Birefringence Crystalline + amorphous <P7.(cos9» Transparent specimens


region; average over required
all chains in polymer

X-ray Crystalline regions Complete characterisation; Difficult to quantify with


diffraction any orientation average low-crystallinity
may be calculated polymer

Infrared Molecular bond or group, <P7(cos8» Very thin specimens


dichroism often in amorphous + and <P4(cos9» required; may set the
crystalline regions but limit in practice
sometimes for specific
region

Raman As infrared dichroism <P7(cos9» Transparent optically


spectroscopy and <P4(cos9» homogeneous and non-
fluorescent specimens
required

Broad-line Usually amorphous + <P7.(cosO» Magnetic anisotropy may


nuclear crystalline regions but and <P4(cos9» not be large enough to be
magnatic sometimes for specific <P,,(cosG» useful; detailed
resonance region and <PR(cosG» molecular structure must
be known

Polarised Usually amorphous regions <P?(cosfl» If the polymer is non-


fluorescence and <P4(COSO» fluorescent. a suitable
spectroscopy marker molecule
must be used
Chapter 1 Introduction 23

This technique is very well known and results compare closely with other
techniques such as NMR(69), fluorescence(70) and Raman spectroscopy(72) .

1.6.2 X-ray DifTraction(XRD)

XRD has been used by many workers(22,23,27,36,46,60,81-84) to study the

structure of PVC. Some examples ofWAXD traces of non crystalline PVC, consisting

of a combination ofthe crystalline (A.) and amorphous scattering (A,.), are shown in
Figure 1.11 (36). Order factors can be calculated as described by Rayner and Sma1l(8S).

Order factor = Ax x 100%


Ax+ A ,

From this value, the crystallinity in the PVC sample can be measured. When

PVC is oriented, the crystallinity is increased, therefore, a change in the WAXD

pattern can be detected. Mammi and Nardi(2S) and Lebedev et al.(27) reported that x-

ray texture patterns of oriented PVC show the 24.5°29 reflection to be independent of

azimuthal angle whereas the 17.5°29 halo is present in the equatorial but absent in the

fibre axis direction. They attribute these results to a mesomorphous or nematic phase

whose order consists in a parallel arrangements of chains. Brady and Jabarin(68), Gilbert

and Vyvoda(62) and Vyvoda et al. (60) have also observed an increase in the intensity of

reflections showing a sharpening of 17°29 peak in the W AXD pattern. Peaks in this

angular region have been shown(22) to be due to (010) (200) and (110) sets of the

planes.
Chapter 1 Introduction 24

35 30 25 :20 15 10
2e(dogreo.)

Figure 1.11 X-ray diffraction patterns for polymer annealed 5 hour:


(A) low temperature polymerised PVC,. (B) PVC2 at 100°C,. (C) PVC2 at 40°C

Vyvoda et at. (60) have concluded that cold-drawing of compression-moulded

material leads to a reduction in 3-dimensional order in the mouldings (a decrease in

height of the 24°29 peak) and an increase in 2-dimensional order (an increase in the

17°-19°29 peak). As a result, after stretching the anisotropy of mechanical properties

Increases.

Liu and Gilbert(63-64) noted that the order factor of uniaxially stretched PPVC

increases with draw ratio, sharply at first, and then appears to reach a limiting value.

Annealing temperatures are also shown the effect on order factor; the higher the

annealing temperature, the greater the order factor. For the biaxially drawn samples,

they reported that the value of the order factor is less than that observed in the

uniaxially drawn samples.

More recently, Gilbert et a1.(86) used A-peak ratio to evaluate biaxial orientation

of PVC. Figure 1.12 shows the change in the x-ray diffiaction patterns of the UPVC

samples at different draw ratios. The peak labelled A was ratioed to the equivalent
Chapter 1 Introduction 25

peak in an undrawn compression moulding. It was found that this ratio increases with

draw ratio (Figure 1.13), and was highest for the UPVC.

Draw Rate 10mm/min


Temperature : 90·C
Annealing Temperature 90·C
1.9X Time : 10 mins

10 20 30 40
ANGLE ·29

Figure 1.12 X-ray diffraction patterns for oriented samples

1.6.3 m Spectroscopy

The IR studies of PVC are focused on the influence of the configurational and

conformational changes of the C-CI groups stretching bands between 600-750 cm-I. It

is a good tool for studying syndiotacticity and conformational fractions. Therefore, IR

. spectroscopy can provide qualitative information about orientation because the

oriented PVC consists of a longer fraction of trans-trans or extent structure which can

lead to the formation of crystalline areas during thermal treatment. The absorbance of

two strong peaks at 602 and 640 cm- I and a weak band at 690 cm- I have been ratioed

as follows; Af>02/Af>90 and Af>401Af>90 are measures of the proportion of syndiotactic

units in planar conformation and hence used as a measure of the crystallinity(81).


Chapter 1 Introduction 26

1.2

1.0~~~~--~--~~--~~--77--~~--~
1.0 1.2 1.4 1.6 1.B 2.0 2.2 2.4
DRAW RATIO

Figure 1.13 Variation a/peak ratio with draw ratio

Infrared dichroism can also provide quantitative measurement of orientation by

the use of dichroic ratios which relate to certain orientation functions characteristic of

the average orientation of structural units within the polymer.

Theodorou and Jasse(67) studied orientation in pure and plasticised PVC by

using FTIR. The results showed that orientation increases with draw ratio and that

long aII-trans syndiotactic sequences orient more readily than amorphous

conformations. They also noted that a plasticiser does not affect the orientation of
PVC at a given draw ratio. These results are in agreement with those of Shindo et
al.(74) and Umemura(87), but in conflict with those of other workers(66.69.70.88), who

suggested that orientation decreases with an increase in either temperature or

plasticiser content.
Chapter 1 Introduction 27

1.6.4 Raman Spectroscopy

In this technique, the intensities of Raman scattering in C-CI the stretching

region of the infrared spectrum are measured and these data are analysed to give

<P2(cos9» and <P4<cos9».

Amongst the pioneer workers, Robinson et a1.(89) and Maddams et a1.(90)

studied the alteration of the stretching mode of C-CI groups brought about by changes

in tacticity, conformation and crystallinity of PVC. These properties were used to

evaluate molecular orientation by Robinson et al. (72) They reported that when PVC

samples undergo cold drawing, the distribution of syndiotactic and atactic sequence

orientations are identical, whereas hot drawing makes the syndiotactic fraction more

oriented than the atactic fraction.

1.6.5 Fluorescence Spectroscopy

Since PVC is non fluorescent, it is necessary to add a suitable molecule to the


PVC chain to create a fluorescing group in PVC molecule. Hibi et a1.(91) used the

fluorescence of polyene and carbonyl groups produced by heat treatment to investigate

the orientation behaviour of a non-crystalline chain and the molecular orientation

behaviour in the uniaxially stretched film. This modified PVC is better than others

created by the addition of fluorescent dyestuffs, because with the addition of dyes the

distribution of orientation of the polymer chains must be related back to the orientation

of the molecules of the additive. However, this method cannot be used directly to

estimate the orientation distribution, because it is necessary to know the ratio of

polyene to carbonyl-molecular distribution function to postulate the relationship. This

is usually difficult, and is a significant disadvantage.


Chapter 1 Introduction 28

1.6.6 Nuclear Magnetic Resonance (NMR)

The broad line NMR measurements of the anisotropy of the proton magnetic

resonance second moment at liquid nitroi~db;imperature for a series of drawn PVC


samples have been studied by Kashiwaghi and Ward(69). The data were used to

calculate orientation functions which characterise the molecular orientation. They

found that the orientation functions for the drawn samples are shown to be consistent

with those obtained from pseudo affine deformation of the aggregate units in the

drawing process and there is a good correlation with birefringence data.

1.7 EFFECT OF IRRADIAnON ON PVC

It is well known that crosslinking of PVC can be induced by irradiation with an

electron beam or y-rays, but the predominant reactions are dehydrochlorination and

chain scission which lead to undesirable material properties. All reactions are largely

dependent upon the radiation dose and radiation time. Crosslinking confers insolubility

while the degradation becomes primarily evident by decolouration. Shapiro(92) and

Alexander et al. (93) discovered these properties of PVC whilst they tried to crosslink

PVC with high energy irradiation (>20 Mrad). Miller(94) found that the addition of

radiation sensitisers, e.g. polyfunctional unsaturated monomers, lead to efficient

crosslinking reactions with low dehydrochlorination at low irradiation doses, and

therefore that specially formulated crosslinkable compounds containing a radiation

sensitiser are required. Upon irradiation the sensitiser is polymerised and crosslinked

into a three-dimensional network into which the PVC is incorporated via a grafting
reaction(94-95). Polyfunctional monomers that have been shown to act as such

crosslinking sensitisers for PVC include, allyl esters(96), dimethacrylates(94-95.97-98),

trimethacrylate(95,97,99), triallyl isocyanurate(lOO), and triacrylates(95) . The polyfunctional


Chapter 1 Introduction 19

methacrylates and acrylates were found to have the greatest sensitivity, especially

trifunctional monomers such as trimethylol-propanetrimethacrylate (TMPTMA) and

trimethylolpropanetriacrylate(95,97-98,IOI-I02). Their use is highly advantageous because

they are effective plasticisers for PVC, forming good contacts with the PVC chains and

facilitating the grafting reaction. They also produce high yields of radicals during

irradiation as a result of their high sensitivity to irradiation.

In addition, there are many variables affecting the occurrence of crosslinks such

as irradiation dose, crosslinking monomer concentration, temperature of irradiation

and the presence of plasticiser and stabiliser.

The mechanism of electron irradiation crosslinking of PVC using polyfunctional


1,,,
acrylic monomers was· investigated by Salmon and Loan~ During the first stage of

the process, the radiation was found to produce free radicals on the PVC chains and

monomers. In the second stage the monomers were found to undergo rapid

polymerisation. The final step involved grafting of the polymer chains formed by the

polymerisation of the activated monomers onto PVC chains, to form a three-

dimensional network. Polyfunctionality of the monomer was necessary for crosslinking

to occur since butyl methacrylate containing only a single unsaturated bond did not

crosslink readily. Trimethylolpropane triacrylate, a triunsaturated compound, showed

40 times the radiation sensitivity of tetraethylene glycol, a diunsaturated compound.


Based upon their mechanism, the radiation sensitiser TMPTMA would produce the

irradiation crosslinking mechanism as displayed in Figure 1. 14.


Chapter 1 Introduction 30

0
11
CH3-CH2-C(CH2-O-C-C=CH2h
I
CH3
- %
El )
IrradiatIon

n~
~.
pvc Irradla"tlon + •

/
b )
PVC J _

~
POLY-TMPTMA

PVC
c )

Figure 1.14 Irradiation crosslinking mechanism (87)


Chapter 1 Introduction 31

Hell et al.(I03) examined the higher dose radiation crosslinking of PPVC in the

presence of triallyl cyanurate as a sensitiser, DOP as a plasticiser and lead and tin

stabilisers. Lead stabiliser gave very good crosslinking yields and the colour stability

was good for radiation doses up to ISO kGy. Tribasic lead sulphate accepts HCI,

formed in the dehydrochlorination reaction during thermal and irradiation processing,

without inhibiting the crosslinking. Tin stabilisers conferred very good colour stability

of samples even up to 300kGy doses, but they strongely inhibited the crosslinking

process.

Kajima, Kumafuji and Ueno(I04), in a study of discolouration of irradiated

crosslinked PPVC found that the lower the irradiation dose, the less the discolouration

of irradiated PVC. The optimum irradiation dose for PVC was under 12 Mrad. The

irradiated PVC discoloured less when the amount of plasticiser was increased. It was

caused not only by dilution of colour but also by the suppression of formation of the

conjugated double bonds which are produced due to the interaction of the crosslinking

agent with PVC molecules. PVC using tin or Ba-Zn stabilisers had less discoloration

by irradiation in comparison with lead stabilisers, but after heat treatment, PVC using

tin and Ba-Zn stabilisers discoloured remarkably. The Ba-Cd-Zn complex also was

recognised to be a poor stabiliser against colour formation upon over-ageing<IOS) .

de Hollain(I06) found that different plasticisers bring about an altered network

stability of the crosslink structure and changed crosslinking efficiency. He also found

the effect of the increase in the free radicals, after storage for 3 weeks, brought about a

reduction of tensile strength (which is then lower than that ofunirradiated PVC). They

suggested that the motion of these radicals can initiate a degradation process and even

cause main-chain scission in PVC. This undesirable result was observed during earlier

work carried out by Dobo(98) , in an extensive study on radiation crosslinking of PVC


Chapter 1 Introduction 32

with ethylene glycol dimethacrylate, which revealed an inexplicable increase in the

concentration of free methacrylate radicals after storage of one week.

Bowmer et al. (107·109) in a study on radiation crosslinking of PVC with

TMPTMA, found that there was an initial preference for TMPTMA

homopolymerisation using 30-40% of the available bonds after which the

remainder of the double bonds grafted to PVC to form the network. Increasing the

irradiation temperature up to 80°C increased all reaction rates but at temperatures

greater than 80°C, the dehydrochlorination of the PVC began to compete with the

grafting and crosslinking mechanisms. Furthermore, post-irradiation annealing may

increase the crosslink density due to the reaction between the residual monomer

molecules and the unreacted double bonds in the crosslinked network. The addition of

phthalate plasticiser to the PVC composition considerably enhances the crosslinking

reaction, and in its presence effective crosslinking may be achieved at room

temperature(108). As the phthalate plasticiser content increases the insoluble part also

increases, due to a higher percent ofthe crosslinked material(llO). The added phthalate

plasticiser acts as a lubricant between adjacent polymer chains and allows greater

movement within the PVC molecules. The increased mobility of the chains leads to a

higher rate of migration of the free and trapped radicals, which in turn increases the
probability of radical collision(lll).

Nethsinghe and Gilbert(ll2) investigated the structure and properties of

irradiation crosslinked PPVC, using a PVC system containing DIOP as a plasticiser

and TMPTMA as a crosslinking monomer. They found that increased irradiation doses

at constant TMPTMA concentration markedly increased the crosslinking efficiency

(gel yield). However, further increases in radiation intensity above 4 Mrad had less

effect. From a crosslink density study, it was shown that crosslink density increased to
Chapter 1 Introduction 33

a maximum at an irradiation dose of 4 Mrad, then decreased as the irradiation dose is

increased further. They explained that the initial network formed by the crosslinked

TMPTMA broke down, at irradiation doses greater than 4Mrad, and the resulting
radicals formed reacted with more PVC molecules to give a more open structure. In

contrast, crosslinking density increased with TMPTMA concentration at constant


irradiation dose, however the gel yield increased with TMPTMA loading. Part 2 of
their paper documented work(l13) carried out on samples produced with varying

concentrations of TMPTMA and with different radiation doses. Studies involved

thermomechanical analysis and the determination of mechanical properties both at


room temperature and I30°C. TMA traces showed the effect of the increased

irradiation dose and the increased TMPTMA concentration. Crosslinking causes the

development of a plateau in the TMA trace, which reflects the modulus of the sample,
and an increase in the softening temperature of PVC. The crosslinking causes only

minor changes in room temperature properties but a significant change in tensile


properties at I30°C. The UTS increases with the irradiation dose and TMPTMA

loading. Elongation at break increases with the irradiation dose, but rises to a

maximum point and then falls away when plotted vs TMPTMA concentration. They
explained that the difference in elongation behaviour as a function of the two variables

must be attributed to the different types of network structure present. The difference in
behaviour at the two temperatures is a consequence of chain mobility which is greater

at high temperatures and hence the restriction in mobility caused by the crosslinks has a
much more significant effect at higher temperatures. Flow in the unirradiated PVC is

only prevented by the presence of small crystallites in the network, which act as
physical crosslinks(ll). At 130°C crystallites partially melt, as can be seen from the

endotherm starting around 100°C in the DSC thermogram(18); in contrast chemical

network structures still remain at higher temperatures.


Chapter 1 Introduction 34

1.8 EFFECT OF CROSSLINKING ON PVC

The mechanical performance of PPVC is very favourable, since the material's

usual operating temperature is well above Tg. The flow behaviour of PPVC is similar

to that of a lightly cross-linked gel (i.e., a rubber type behaviour). This has been the

subject of much debate, but the most reasonable explanation is the presence of a

physical network consisting of a small crystallites(II). An obvious way to increase the

maximum useful operating temperature of PPVC products is to introduce a permanant

chemical network (crosslinking structure) into the material.

Besides irradiation crosslinking (as mentioned in the previous section),

chemical networks can be introduced by chemical crosslinking. Chemical methods

involving reaction with organic peroxides are not satisfactory since degradation

predominates over crosslinking and crosslinking would be introduced during

processing(94). Multifunctional organic mercapto compounds give very good results(lI4-

119) but practical applications are prevented especially by processing limitations and also

by the decreased thermal stability of the products. Organosilanes are the alternative
crosslinking agents that have been used by a number of investigators(120-12S). Chemical

crosslinking is normally a two-step procedure. Firstly, compounding and forming must

be performed under conditions which do not activate the crosslinking reactions, which

are initiated in the second step, often by application of heat, usually by immersion in

hot water. The process has its disadvantages, namely susceptibility to premature

crosslinking and degradation of the PVC.

An early application area for irradiated PVC was general purpose wiring

insulation for compact equipment such as radios, television sets, and computers since it

gave good resistance to heat damage brought about by the use of soldering irons
Chapter 1 Introduction 3S

during assembly. Polytetrafluoroethylene (PTFE) shows the best properties for this
purpose. Bennett(126) studied the hot soldering iron resistance and deformation

resistance of PVC, crosslinked PVC and PTFE. He found that crosslinked PVC

offered a practical degree of soldering iron resistance, but the irradiated crosslinked
PVC additionally offered much improved mechanical deformation resistance in service.

These advantages of crosslinked PVC in the field of wire insulation were also found by
a number of researchers(IDS,127-132). The application of irradiated PPVC in pipes was

studied by Hell et al.(IDI). They found that the resistance to internal pressure of

crosslinked PPVC pipes at 80 0 C was higher than that ofunirradiated PPVC pipes.

Hjertberg and Dahl(llS) studied the co-operation between chemical and physical

networks in crosslinked PPVC. DSC and penetration as a function of temperature


were used to detect the change in melting behaviour and to follow the change in

mechanical properties, respectively. Chemical crosslinking was performed by using a

dithioltriazine. Figure 1.15 shows that even rather low degrees of crosslinking, hence
low gel content, gave a substantial reduction in penetration over the temperature range

60-110°C, while a more complete crosslinking reaction prevented major penetration up


to at least 200°C. The penetration curve of heavily crosslinked materials showed

several plateaus and the transitions could be related to the melting of different
crystallites formed by annealing at various temperatures. The physical network formed

by the crystallites constitutes an important complement to the chemical network in


PPVC crosslinked by dithioltriazine. Both the amount and the melting temperature of

the crysta\lites increased after annealing. The introduction of the chemical network
further improved the heat resistance of the crystallites. The presence of the two

networks therefore shows a synergistic effect with respect to the mechanical properties

at increased temperatures.
Chapter 11ntroduction 36

o
100% gel

0.05

E 9&%
E
\
\
\
\
0.10 \
\
\
\
\
\
\
\ 76%
0.15 \
I
I
I
\
\

50 100 150

Figure 1.15 Penetration resistance(t1I) as a/unction temperature; (- - -) normal


• (lIS)
PVC; (-) Crosslmked PVC

Some features of crosslinked PVC are summarised as follows(133·134) :

1. Formulation flexibility - Crosslinked PVC can be compounded to meet

varying property requirements.

2. Excellent abrasion resistance - Abrasion resistance is improved by a factor of

10 or better after irradiation.

3. Improved toughness - Resistance to cut through is upgraded markedly. This

effect is enhanced at temperatures in excess of 100°C.


Chapter 1 Introduction 37

4. Resistance to high temperature deformation - Appropriately formulated

crosslinked PVC will withstand application ofa weighted solder iron at 350°C.

5. Reduced solubility in many solvents

6. Dimensional stability- Shrinkage effects at elevated temperatures are

significantly reduced.

7. Opportunity to reduce thickness and weight - Due to excellent physical

properties of crosslinked PVC.

8. Retention of the processing advantages of thermoplastic PVC - Because

irradiation crosslinking is not carried out until forming operations have been

completed.

In conclusion, the three dimensional polymeric network of crosslinked PVC

gives rise to a superior range of properties and new application possibilities.

1.9 EFFECf OF ORIENTATION ON PVC

As stated in section 1.5, monoaxial orientation of UPVC resulted in increased

tensile strength in the draw direction whilst reducing it in transverse direction. Similar

effects can be induced in PPVC samples, providing that they are annealed in the

stretched state prior to cooling. There is a keen interest in biaxial orientation (the

planar orientation of molecules) since it produces good planar properties.


Chapter 1 Introduction 38

Work recently undertaken by Gilbert et al.(86.13S) has highlighted the

relationship between biaxial conditions, properties and structure. They concluded that

the draw ratio has the most significant influence on the mechanical properties of

biaxially oriented samples of both UPVC and PPVC. It was shown that alteration of

the draw and annealing temperatures delayed the onset of sample shrinkage upon

heating. Tensile properties were measured in the biaxial stretch directions of the

samples (0° and 90°) and also at 45° to these. The results were found that the tensile

properties were the same over the whole of the plane of the film. It appears that

molecular chains were uniformly aligned in the plane of the film by the stretching

process. The presence of aligned polymer chains will increase strength, but restrict

further chain extension so that elongation at break is reduced. Impact strength

increased linearly with draw ratio as a result of alignment of PVC molecules in the

plane of the film. In contrast, tear strength decreased with increased planar strain. They

suggested that planar orientation will reduce the amount of chains and loops

perpendicular to the sheet plane, thus tearing can occur more easyily in the plane of the

sheet. This effect was proved by scanning electron microscope (SEM) photographs of

the tear surfaces. The undrawn sheet produced an irregular surface, whilst that for the

biaxially drawn sheet shows regular parallel tears. It was apparant that biaxial

orientation produced a laminar structure.

Gilbert and Hitt(86.I36) examined sample shrinkage caused by heating, using

thermomechanical analysis (TMA). The effect of drawing and annealing temperatures

upon the variation of area shrinkage with temperature is shown in Figure 1.16. An

increase in annealing temperature modified the shrinkage behaviour, but the use of

higher temperatures reduced the maximum possible draw ratio. The variation of

elongation at break with temperature gave maximum values in the range 80_90°C for

UPVC and PPVC compositions(137), therefore the decrease in maximum draw ratio at
Chapter 1 Introduction 39

temperatures greater than 90°C lead to sample failure. The samples were stretched at
90°C with the maximum draw ratio to achieve the highest tensile properties, followed

by annealing at temperatures greater than 90°C. Consequently, tensile and shrinkage


properties were controlled by selecting the most effective draw ratio and annealing

temperature. They also investigated the room temperature recovery rate of biaxially
oriented PVC(138). The rate of recovery was found to increased with plasticiser

concentration, while the sample areas decreased exponentially with time by two
distinct steps; during the first day the samples recovered quickly followed by a slower

recovery rate at later times. The area shrinkage observed in oriented PVC, both with

temperature and time, is a disadvantage of the material.


110

100

90 Drawn at 100mm/m1n ~ 1.5X


Annealed for 10mina
BO

70 TEMPERATURES
w
'"... 60 Oraw
'z"
~
Annealing
a: 50
:t
Ul
...
w
40
a:
.'" 30

20

10

-10
30 40 50 SO 70 BO 90 100 110 120 130 140 150 160
TEMPERATURE (OC)

Figure 1.16 Effect of drawing and annealing conditions on area shrinkage

1.10 AIMS OF TIns PROJECT

The experimental work outlined herein forms a part of a large programme

being undertaken in the Institute of Polymer Technology and Material Engineering,


Chapter 1 Introduction 40

which is aimed at studying the relationships between biaxial stretching conditions,


structure and physical properties of oriented PVC products. The overall programme is
outlined in Table 1.2(139).

As mentioned in section 1. 9 biaxial orientation can enhance the physical

properties of PVC, however the shrinkage behaviour of oriented PVC limits the range
of applications to which the material can be put, especially when high service

temperatures are likely to be experienced, due to the loss of orientation which occurs
under these conditions. Irradiation crosslinking modifies the properties of PPVC

confering improved physical performance at high temperatures and dimensional


stability etc, therefore, it is of interest to combine these two methods to upgrade the

polymer's properties.

To date investigations have been concerned with either oriented PVC or


crosslinked PVC, and not with the effect of the combination of both techniques. This

project was aimed at the enhancement of the properties of PPVC compounds by biaxial
stretching followed by irradiation crosslinking. It was hoped that crosslinks introduced

into the already oriented PPVC would prevent the loss of properties at high
temperatures and reduce the room temperature recovery rate by holding molecules in

the oriented state.

This work was divided into three stages: firstly, to confirm that a crosslinked

structure can be introduced into the oriented samples; secondly, to study the effect of
each component in the formulations and the effect of irradiation dose on physical

properties of the material, and thirdly, to characterise the crosslinked oriented samples.
Chapter 1 Introduction 41

Table 1.2

A Construction of biaxial stretching B. Measurement of optimum draw ratio


Variables:
stretching equipment
Plasticizer content (0-70 phr)

/
Temperature
Stretching rate

C. Preparation of selected biaxially Molar mass of PVC


stretched samples
(a) Rigid, no annealing
(b) Rigid, selected annealing conditions D. Development of thermal analysis
(c) Flexible. selected annealing conditions and x-ray techniques to detect
structure

E. Measurement of:
(a) sample shrinkage as a function
of temperature
Assessment of structure by:

(b) Tensile properties Thermal analysis


(c) Impact properties of rigid samples X-ray analysis

O. ModifYing drawing/annealing conditions to achieve optimum properties

H. Repeating steps E and F I. Production of crosslinkable


formulations:
Drawing or drawing and annealing
under optimum conditions

Repeating steps E and F

Proposing relationships between formulation, drawing conditions, structure and


properties, to enable:

(i) Planning of new programmes related to specifice applications;

(ii) Identification of optimum processing conditions for oriented PVC products;

(iii) Development of new products based on enhanced properties.


Chapter 2 Experimental Procedures 42

CHAPTER 2

EXPERIMENTAL PROCEDURES

2.1 MATERIALS

2.1.1 Polyvinyl Chloride(PVC)

A commercial grade of suspension PVC homopolymer, supplied by European

Vinyl Corporation (EVC plc), was used throughout the work carried out. This
particular resin is specially designed for use in plasticised compositions. The polymer

grains are irregular in shape and have a uniform and highly porous structure. The

technical reference for the grade is CORVIC S71/102(or SH7020) and its main

characteristics are given in Table 2.1.

Table 2.1
Properties ofCorvic s711102

PROPERTY VALUE TEST


METHOD

K Value 71 a*
Molecular weight (Mw) 121000 b*
Molecular weight (Mn) 71000 b*

*Test methods:
a: Calculated from relative viscosity data obtained by method ISO-R174

b: Estimated by GPC
Chapter 2 Experimental Procedures 43

2.1.2 Trimethylol Propane Trimethacrylate(TMPTMA)

TMPTMA, a polyfunctional unsaturated monomer supplied by Ancomer UK,

was used to promote irradiation crosslinking of PVC. The structure of the TMPTMA

molecule is shown below. TMPTMA is a clear liquid at room temperature with a

boiling point higher than 200°C @ Imm Hg.

TMPTMA

2.1.3 Stabilisers

Three commercial grade lead stabilisers and tin stabilisers were used. All

stabilisers were supplied by Akzo Chemical, UK. The technical data on these additives

are presented in Table 2.2.

2.1.4 Plasticiser and Lubricant

Di-isooctyl phthalate (DIOP), C6H4(C8H 17COO)Z, a clear liquid with a

density of 0.98 g/cm 3, was used as a plasticiser and was supplied by Exxon. Stearic

acid, supplied by Akzo Chemicals, was used as a lubricant.


Chapter 2 Experimental Procedures 44

Table 2.2
Technical data on stabilisers

STABILISER FORM! SPECIFIC MELTING %LEAD


COLOUR GRAVITY POINT!OC CONTENT

Tribasic lead Powder! 6.3 - 83.4


sulphate(TBLS) White
3PbO.PbS04· H 7. 0

Lead stearate Powder! 1.8 104 28


Pb(07. C·17Hl',h White

Dibasic lead
stearate(DBLS)
Powder!
White
2.0 - 51

2PbO.Pb(O?C.C17Hl~h

Stanc\ere T186
(Dibutyltinmercaptopropionate)
Powder!
White
- HO-l30 -
(C4H9h-Sn-(SC?H4CO?)

Stanclere T184
(Dibutyltin substituted mercaptide)
Clear amber
liquid
1.11 - -
(C4H9h-Sn-(SCH?C01R)

Stanc\ere TL
(Dibutyltindidodececanoate or
Clear amber
liquid
1.04 - -
Dibutyltindilaurate)
(C4H9hSn(07.CCllH7.1h

2.2 SAMPLE PREPARATION

2.2.1 Fonnulations

The formulations presented in Table 2.3 were used in this study. Formulations
FI and F2 were used in Chapter 3 for the purpose of studying the possibility of

crosslinking oriented samples. Formulation F3-F13, which contained different types

and concentrations of stabilisers, were used to evaluate the effect of stabiliser on

crosslinked oriented samples. For the study into the effect of TMPTMA and stabiliser
Chapter 2 Experimental Procedures 45

concentration upon the properties of PPVC products the formulation T2-T20 and S2-

S6, were used, respectively. Formulation P25, which contained less plasticiser than the

other formulations, was used to determine the influence of plasticiser on the properties

of the final products.

2.2.2 Dry blending

An 8 litre T.K. Fielder laboratory high-speed mixer was used to prepare all
formulations studied. The PVC resin and powder components were initially agitated in

the mixer at 75°C, after a short time the plasticiser and crosslinking monomer were

added. Mixing was continued, at a speed of 3,000 rev/min., until a temperature of

120°C was reached, after which the compound was discharged into the cooling

chamber of the mixer where it was agitated and cooled to below 25°C.

2.2.3 Milling

According to the recommendations in BS 2782: Part 9 Method 901A: 1977,

milled sheet was produced for the purpose of compression moulding (Section 2.2.4).
The mi11ing process is an essential step in sample preparation because fusion of the

PVC takes place, whereas compression moulding of the dryblended powders directly

resulted in inadequate fusing of the PVC material.

The powder blend was mixed on a two-roll mill for 5 min at 140°C to produce

sheets of approximately 0.2 to 0.4 mm in thickness.


Chapter 2 Experimental Procedures 46

Table 2.3

Formulations(phr)

SAMPLE PVC DIOP STEARIC STABILISER TMPTMA


CODE ACID

lBLS
FI
F2
lOO
lOO
46.5
46.5
0.5
0.5
7
7
-- 0
10

Pb Stearate DBLS
F3 100 46.5 0.5 4 - 10
F4
F5
lOO
100
46.5
46.5
0.5
0.5
6
3
-
.3
10
10
F6 lOO 46.5 0.5 - 4 10
F7
F8
100
100
46.5
46.5
0.5
0.5
-- 6
8
10
10

Stanclere T1 86
F9
FIO
lOO
lOO
46.5
46.5
0.5
0.5
4
6
-
-
10
10
Fll 100 46.5 0.5 8 - 10

Stanclere TL
FI2 lOO 46.5 0.5 4 - 10
P25 100 25 0.5 3 - 10

Stanclere T1 84
F13 lOO 46.5 0.5 4 - 10

Stanclere TL
T2 100 46.5 0.5 4 - 2
T5 lOO 46.5 0.5 4 - 5
TlO
(=F12)
100 46.5 0.5 4 - 10

T20 lOO 46.5 0.5 4 - 20

S2 lOO 46.5 0.5 2 - 10


S3
S4
100
lOO
46.5
46.5
0.5
0.5
3
4
-- 10
10
(=F12)
S6 lOO 46.5 0.5 6 - 10
Chapter 2 Experimental Procedures 47

2.2.4 Compression moulding

The milled sheet was compression moulded to a thickness of approximately


0.25rnm for samples to be used without stretching and approximately 0.5rmn for

samples to be subsequently stretched. Samples were moulded at 175°C for 5 min (after
a five minute preheat period), at a pressure of 60MPa. The mould was then

immediately transferred to a water-cooled press and cooling was effected under the

same pressure. The mouldings used for the work outlined in chapter 3 had a thickened
frame as shown in Figure 2.1 and those for the experiments described in chapters 4 and

5 flat sheets were used. Samples were marked with inked lines 10rmn apart in both
vertical and horizontal directions to form squares, and the sheet thickness at the centre

of each square was recorded for the purpose of draw ratio calculation.

"ll ..B-
140
tl
I A
---- '
-'1A
1_ I
I --:~- I
I
=
I j
0·6
=
2
section A-A

Figure 2.1 Compression moulding. (Dimension in mm)


Chapter 2 Experimental Procedures 48

2.2.5 Biaxial Stretching

The biaxial stretcher used in the preliminary investigation (chapter 3) is shown

in its closed position in Figure 2.2(a) and in the extended position, with a sample
present, in Figure 2.2(b). This attachment was designed to fit into the high temperature

cabinet on an Instron tensile testing machine. The size of the unstretched sample

required for this attachment is 55mm by 55mm.

(a) (b)
Figure 2.2 Biaxial stretching attachment: (a) in closed position; (b) in extended
position with sample present

For the rest of the study bigger samples, 116mm by 116mm, were used with
the Biaxial Stretching Equipment (the BASE). The BASE was designed as an
attachment for an Instron tensile testing machine (Figure 2.3). The full details of this

equipment, including specifications, stretching mechanism and operating procedures,


have been described by Hitt and Gilbert(I40). The stretching head was located within the
Chapter 2 Experimental Procedures 49

environmentally controlled cabinet, which can be operated at temperatures up to

200°C. The heating system works by circulating hot air through the cabinet. The

stretching head has two draw rods which are perpendicular to each other (Figure 2.3).

These two rods were moved simultaneously at the same rate to produce equally

biaxially stretched samples. The stretching head of the BASE is shown in its zero

position in Figure 2.4(a} and opened to a displacement of 160mm (both axes) in Figure

2.4(b}. Samples were held by ten grips upon each edge, operated under nitrogen gas

pressure, their function being to only apply a force in the direction in which the sample

was being stretched. The grips were designed so as to allow the material held by them

to draw down during stretching so that the elongation undergone by the material in the

grips could equalise with that of the rest of the sample.

The samples were stretched at 80°C at a rate of 10 nunimin, followed by

annealing whilst being held in the drawn state at the same temperature (unless stated)

for 20min. Finally the samples were cooled down to room temperature in the stretching

attachment. Figure 2.5 shows an undrawn sample, a sample after clamping and a

stretched sample. The draw ratio(t..} of a stretched sample is defined by the equation

given below:

t.. = rt ..... 2.1


Vt.
where tb = sheet thickness before stretching, at a given marked square

ta = thickness at the same square after stretching


Chapter 2 Experimental Procedures 50

• Un stretched Sample
IZI Stretched Sample (maximum size)
1. Crosshead of Instron
2. Environmental Cabinet
3. Draw Rod
c.. Hydraulic Cylinder
S. Air Outlet Duct
6. Air I nlet Du et
7. Support Frame· of BASE

2I

3
I
I
i }-_~=:=__ j_._~J::::\--_-L..J......_-Y
I

/
~------------

Figure 2.3 Schematic diagram ofBASE


Chapter 2 Experimental Procedures 51

.,
l

(a) (b)

Figure 2.4 The stretching head of the BASE (a) in zero position and
(b) opened to 160 mm displacement

: [iI)

I I I I I I Ii ~!'"~~~~l
i '_l-~-'-\~\-I (
, , !
1_1_1_1_1_1-1_1-1 ! .~ 1,

I I i I I I i ! :1 j

I ili]-n-l-i_r_I_:
. 1

i.
,
, i-ITI ! I l i t 1-:·-)
~

I Ibl 'i .
!llJ ill-I-·1- 1

: il I I !

-,-,-,-, - - - -
:

Figure 2.5 Samples before and after stretching. (a) an undrawn sample,
(b) a sample after champing and (c) a stretched sample
Chapter 2 Experimental Procedures 52

2.2.6 Irradiation

Crosslinking was induced by exposing the samples to electron beam(EB)

irradiation. The samples were irradiated on each side with a dose in the range of 2-8

MRad. All irradiation was performed under a nitrogen atmosphere.

2.3 CHARACTERISATION AND TESTING

2.3.1 Assessment of Crosslinked Structure

2.3.1.1 Percentage Gel Content

The gel content, the content of insoluble material in tetrahydrofuran(THF), is

the most frequent method used to evaluated the degree of crosslinking. Gel content

relates directly to network structures formed in crosslinking process. The samples

were examined for gel content by extracting the specimens with THF in a

Soxhlet apparatus for 24 hours. Overnight extraction was used by many

researchers(1l4.124. 141 l, to be certain that none of the dissolved material remained in the

thimble. The extracted samples were vacuum dried at 60°C for at least 20 hours and

the percentage gel content was determined from the remaining weight of a11

components which could be involved in gel formation, the plasticiser being excluded,

as shown in equation 2.2.

% gel content = Wg xlOO ..... 2.2


Wx-Wp

where

Wg = weight of gel
Wx = weight of crosslinked specimen
Chapter 2 Experimental Procedures 53

Wp =weight of plasticiser in the specimen

2.3.1.2 Crosslink Density Measurements

The molar mass between crosslinks, Mc, and the crosslink density in the gels,

1/(2Mc), were obtained from swelling measurements. Samples were allowed to swell

in methyl ethyl ketone(MEK) for 4 days at 25°C. The weights of gel before swelling

(deswollen weight, Wd) and after swelling (swollen weight, Ws) were recorded to

calculate the volume fraction of PVC (vr) in the network swollen to equilibrium.

Crosslink density was calculated from the Flory-Rehner equation (145) , shown below.

1
-[In(l-vr) +vr+Xvr2] = pVovr 3 Mc-I ..... 2.3

where

x = the polymer - solvent interaction parameter


p = the density of PVC

V0 = the molar volume of solvent

vr = the volume fraction of PVC in the swollen gel

2.3.2 Mechanical Properties

2.3.2.1 Tensile properties

Tensile tests were carned out both at room temperature and at elevated

temperatures (70°C, 100°C or 130°C) using a Hounsfield tensile testing machine with

at test speed of 50nun/min. The tensile strength and elongation were determined at the

fracture point of each specimen. Due to the limited sample area available and the

requirement that specimens be of equal thickness for all crosslinked oriented materials,
Chapter 2 Experimental Procedures 54

a smaller tensile sample cutter than that specified in the British Standard (BS 903)

was employed. A cutter with dimensions; Smm width, 26.5mm in length and 10mm in

guage length was made specially for this purpose.

2.3.2.2 Impact Testing

A Rosand instrument falling weight impact tester was used to assess the effect

of orientation and cross1inking on the samples' impact strengths. The tests were

performed at room temperature, in accordance with BS 2782, Part 3, Method 3S2D.

The impact velocity used was 3 mls.

2.3.3 Thermal Analysis

2.3.3.1 DitTerential Thermal Analysis

The DSC traces were obtained using a Du Pont Instruments 2000 Thermal

Analyser fitted with a 91 0 DSC cell. Specimens with sizes between 10-12 mg were

scanned from -50°C to 150°C and from room temperature to 240°C, at a heating rate

of IOoe/min, under a nitrogen atmosphere.

2.3.3.2 Thermomechanical Analysis (TMA)

2.3.3.2.1 Softening Temperature (Ts)

Softening temperatures were determined using a Du Pont 990 Thermal analyser

fitted with a TMA attachment operating in the penetration mode. The temperature was
Chapter 2 Experimental Procedures 55

ramped from room temperature to 220°C at 10°C /min, with the probe loaded with a

weight of 109. The penetration of a probe into the sample was plotted against

temperature. Ts was obtained from the experimental trace as shown in Figure 4.1.

2.3.3.2.2 Shrinkage Measurement

A Mettler TMA 40 Thermo Mechanical Analyser was used for shrinkage

measurement, as shown in Figure 2.6 with its film & fibre attachment in position. The

attachment is surrounded by a furnace, which was used to produce a heating rate of

lOoe/min. The sample was held between two grips, the upper attached to the sample

support and the measuring probe suspended from the lower. The probe was attached

to the core of a differential transformer. The arrangement works by the fact that as the

sample moves the core moves equally generating a signal proportional to the sample

displacement. A micro processor converts the signal into a plot of displacement versus

temperature. A calibration weight located within the TMA is used to apply a load to

the measuring probe. The microprocessor controls the application of the load and for

this study a load of O.OIN was used.

The dependence of displacement on temperature curve generated by the TMA

is only a measure of linear shrinkage. The method used to calculated area shrinkage,

which is more sensible measurement for a biaxially drawn material, was shown in

Figure 2.7(136). Two strips are cut from a drawn sample (step A), one parallel to the

vertical draw direction and one perpendicular to it. The linear shrinkage (i1L) is

measured for each strip as a function of temperature (step 8). The value of i1L\& i1L2

can then be used along with the draw ratio of the sample to calculate the area

shrinkage (AS) at any temperature (step C)


Chapter 2 Experimental Procedures 56

FURN .....cE
Si';.(i~

LVOT

Figure 2.6 Mettler TMA40


Chapter 2 Experimental Procedures 57
A. l)rawn sample B. TMA curves

i
CW----- I
I, I
i
J

!
Temperature Temperature

C.AJeasbrinkage(AS)
Area 0/ drawn
sample

'OIDR I area
L_o_'_.'g_'n_o'_-"-_ _.......---'
Area after
shrinkage

OR = Draw ratio

AS maximum = 102 - (loIDR)2

AS at temperature T = 102 - (lo-AL,)(lo-AL2)

AS at temperature T x 100
%AS =
AS maximum

10 2 -(lo-AL\)(lo-AL 2) x 100
%AS =
10 2 -(10 2 IDR2)

(DR)2 [loAL\ +loAL 2 -AL\ALz] x 100


%AS =
(DR)2 -I 10'

(OR)2 (ALl + AL2 _(ALl X ALz)( x 100


%AS =
(DR)2 -1 10 10 10 I.

Figure 2. 7 Calculation of area shrinkage


Chapter 2 Experimental Procedures 58

2.3.4 X-ray Diffraction Measurement

Wide angle x-ray diffraction (WAXD) traces were obtained using a JEOL DX-
GE-25 generator, which was operated at 40 kV and 30mA, and a DX-GO-S vertical

goniometer. Ni-filterted Cu Ka was used under atmospheric conditions. Figure 2.8


shows a schematic diagram of reflection diffractometer geometry. Reflectance mode

measurements at ambient temperature were made using flat rectangular samples

(20mmx14mm) and the diffraction intensity in arbitrary units were obtained over the
range 100 -500 29 with a 10 29 per minute scattering speed. No correction was made

for air scattering; the variation of scattering intensity with 29 was recorded.

Transmission X-ray measurements were made with samples of approximately

0.1-0.2 mm thickness and a sample to film distance of 5 cm. The exposure time was at

least 24 hours. Scattered intensities were recorded photographically.

DETECTO~

,
Sarrp I e
,,
,
,,
,

Figure 2.8 Diagrammatic arrangement ofthe x-ray diffraction


Chapter 2 Experimental Procedures 59

2.3.5 Birefringence

In this study, the optical anisotropy of the sample films was characterised in

relation to three principal refractive indices, a, ~ and y. It was found that the smallest
index, a, was perpendicular to the film plane, thus the birefringence measured in plane

was (y-~) and those for out of plane were (y-a) and (~-a). For equal biaxial
orientation the average of these two values was used to represent out of plane

birefringence; [(y-a)+(~-a) ]/2.

Measurements ofbirefringence were carried out using a microscopical method.


Specimens were cut from a number of positions across the whole of the oriented sheet.

In the determination of in plane birefringence (y-~), the specimens were mounted


between a microscope slide and coverslip in glycerol (refractive index ni; = 1.54) to

reduce light scattering and depolarisation at the film surfaces. Three measurements

were carried out on each specimen using a Zeiss Universal microscope equipped with

crossed-polar:
1. The angle between the side of the specimen, which is paraIlel to the vertical
direction of the sheet, and the nearest extinction position was measured.

2. The direction of y was determined using a one wavelength accessory plate.


3. The in plane birefringence was measured with a quartz Eringhaus
compensator using light of wavelength 546.1 nm.

The OPD and &t can be calculated by the formulas<l46l :

OPD A.= .E.~( a/-sin 2 i) - ~( El -sin 2 i) ..... 2.4


())

&t = OPD/t ..... 2.5


Chapter 2 Experimental Procedures 60

where OPD = optical path difference in run at wavelength A.


A. wavelength in run
Ol = refractive index of ordinary and
& = refractive index of extraordinary wave in quartz for the wavelengtA.
i = the angle of tilt of the plane relative to its zero position
t = the thickness of sample
According to Gifford values(147) refractive index Ol is 1.661 and & is 1.487 at the
wavelength of 546. 1run.

Conoscopy was used to measure out of plane birefringence. In this technique,


the specimen on the stage of the microscope is illuminated with highly convergent
light(14S-149). The light passing through the specimen is viewed at the back focus plane
of the objective lens. The pattern of light seen in the back focal plane or detected by a
camera is known as an interference figure. The interference figure consists of rings of
polarisation colours in white light, or dark and bright 'fringes' in monochromatic light.
These fringes correspond to the position in the back focal plane where the rays passing
along an optic axis (OA) emerge (Figure 2.9). Superimposed upon this pattern are
black 'brushes' or 'isogyres' marking where light passing through the specimen has
encountered permitted vibration directions which are E-W and N-S.

A typical interference figure for a biaxial specimen in the 45° position is shown
in Figure 2.10. Upon rotation of the specimen to the 0° position the pattern changes to
that shown in Figure 2.11. The maximum distance (d) between these two isogyres (in
the 45° position) was used to calculate out of plane birefringence. The optical axial
angle (2V) is the angle between the optical axes which is a characteristic feature for
biaxial specimen as the differences in d are caused by the differences in 2V. In practice
Chapter 2 Experimental Procedures 61

the angle between the emerging rays (2E) was calculated from via d by equation 2.6,

because the light refracts at the surface of the specimen(Figure 2.12).

d = k(sinE) ..... 2.6

The constant k can be calculated from the measurement of d of mica, which was used

as a known crystal, under the same conditions experienced by the samples. For mica

2V is 45° and ~ is 1.582. By using equation 2.6 and 2.7, the constant k was achieved.

sinE = ~sinV ..... 2.7

2E of specimen can be converted to give 2V using equation 2.7 (where n2 is

the intermediate refractive index). Out of plane birefringence of specimen (~-a) was

calculated by using Malliad's rule(149) (equation 2.8), where (y-~), in plane

birefringence, was measured by a quartz Eringhaus compensator.

tan2V= fJ-a ..... 2.8


y-fJ

. __________ ________ .':.. : .i.•. ____ . - --. -. __ .... -.


~.;..' Crysta./

Figure 2.9 Surfaces of equal retardation around the optic axes of a biaxial crystal
Chapter 2 Experimental Procedures 62

Figure 2.10 Interference figure at 45' position

Figure 2.11 Interference figure at extinction position (0 ')

Figure 2.12 Real and apparent optic axial angles


Chapter 2 Experimental Procedures 63

2.3.6 Density Measurement

The densities of samples were measured using a Davenport density gradient


column at 23.0±O.I°C. The column was filled with aqueous calcium nitrate and
calibrated with glass floats with accurately known densities. The height at which each
specimen floated in the column was recorded and converted to density by the standard
calibration curve plotted between heights and densities of the glass floats. The average
of three measurements was used for each sample.

2.3.6 Ageing Study

The effect of stabiliser upon heat stability of materials used was assessed usirig
ASTM: D 2115-67. Samples were exposed in an oven at a temperature of 177±O.SoC
for one hour, and the change in colour of samples was noted.
Chapter 3 Preliminary Investigation 64

CHAPTER 3

RESULTS AND DISCUSSION

I. PRELIMINARY INVESTIGATION

3.1 INTRoDUCTION

The aims of this part of the project were firstly to find the most effective

stretching temperature, secondly to investigate whether crosslinks could be introduced


into oriented PPVC and thirdly to see how properties were modified in the samples

produced. The formulations Fl and F2 were used in this study. Formulation F2 was

shown to be an effective composition for irradiation crosslinking by Nethsinghe and


Gilbect<ll2-l\3) (as discussed in section 1. 7). The crosslinked products were found to

have high percentage gel contents and improved tensile properties, especially at higher
temperatures. Formulation Fl was used as a comparative material because the

crosslinking mono mer (TMPTMA) was excluded in this composition. A radiation dose
of 4 Mrad was used to irradiate each side of the undrawn samples, as this dose gave
the best properties for this formulation according to Nethsinghe and Gilbert(II2). The

drawn samples were irradiated with a dose of 2 Mrad on each side. The reason for
using a smaller radiation dose for the drawn samples than for the undrawn samples was

to make sure that the materials in all samples were exposed to the same total energy

because the drawn samples were thinner. However, the doses 2 and 4 Mrad were
approximate values. A more detailed study of the effect of sample thickness on
properties is considered in Chapter 5. The results obtained from the experiments

carried out- will be discussed under the following heading : stretching temperature,
Chapter 3 Preliminary Investigation 65

percentage gel content, softening temperature, shrinkage, tensile properties and

WAXDstudy.

3.2 EFFECT OF TEMPERATURE ON PERCENTAGE ELONGATION AT BREAK

The purpose of this section was to find the optimum orientation temperature

for PPVC F2. Samples were tensile tested at a range of temperatures. The plot of

elongation at break as function of temperature for PPVC F2 before crosslinking is

shown in Figure 3.1. It can be observed that elongation at break rises to the maximum

at the temperature of 80°C and then decreases. This shape of this curve has been seen

before by Hitt and Gilbert<137). They found that all of the curves for 0, 30, 50, 70 and

100 phr plasticised PVC have a peak elongation in the temperature range 80°C_90°C.

Hence, throughout this study, a stretching temperature of 80°C was selected to give

the maximum draw ratio of the drawn samples.

3.3 PERCENTAGE GEL CONTENT

Gel content is used as a measure of the amount of insoluble, i.e. crosslinked

PVC in a sample. Table 3.1 shows that the gel content of both drawn and undrawn

samples increases after irradiation. This suggests that crosslinked structures were

formed during exposure to an electron beam. The unoriented sample gave the highest

percentage gel content, because it was irradiated with a higher dose of radiation

than the stretched samples. The thickness of specimens was also considered, as

the difference in sample thickness led to the variations in the total irradiation intensity

experienced by each test specimen. The effect of sample thickness upon percentage gel

content will be discussed in detail in Chapter 5.


1,-' _E_L_O_N_G_A_T_IO_N_A_T_B_RE_A_K_v_s _T_E_M_P_E_RA_T_U_RE_----'~
600,------------------------------------------------------,

500

~400
....
~
~
Cl
.9 300
~

I
Ul200
~

100

O+-------~------_.--------._------,_------~------_.--~

10 30 50 70 90 110 130
Temperature/oC
Figure 3.1 Elongation at break as a function of temperature for PPVC F2
Chapter 3 Preliminary Investigation 67

Table 3.1
Softening Temperature and Percentage Gel Content of Un irradiated Oriented and
Unoriented F2 and Irradiated Oriented and Unoriented F2

SAMPLE SOFTENING %GEL


TEMPERATUREJOC CONTENT

F2 (unirradiated) 93.5 0

F2 (irradiated) 103.0 51.7

SF2 (irradiated) (1..=1.3) - 35.5

SF2 (irradiated) (1..=1.6) - 36.3

SF2=stretched F2, 1..=draw ratio

3.4 THERMOMECHANICAL ANALYSIS

3.4.1 Softening Temperature

Figure 3.2 shows TMA traces ofunirradiated and irradiated PPVC F2. It can

be noted that the irradiated sample gave the longer temperature range for penetration

resistance than the unirradiated sample. This was further evidence for a modified

structure in the irradiated specimens. However the softening temperature of irradiated

PPVC given in Table 3.1 was not improved as much as was expected. For the oriented

samples measurements were unsuccessful due to the rapid shrinkage of samples at

higher temperatures.
--------------------------------------------------------------------------

_T_H_E_RMA
1,-' __ L_M_E_C_HA_N_I_C_A_L_A_N_A_L_Y_S_I_S---,,~
80,------------------------------------------------------------,

70

20
---
Irradiated sample
-+-
Unirradiated sample
10+---------,----------.---------r---------r---------.--------~

20 40 60 80 100 120 140


Temperature/CC
Figure 3.2 Penetration resistance for irradiated and unirradiated samples
Chapter 3 Preliminary Investigation 69

3.4.2 Shrinkage

The area shrinkages of the drawn samples before and after irradiation are

shown in Figure 3.3 It can be seen that crosslinking PVC affected the area shrinkage of

the irradiated samples. The unirradiated specimens showed shrinkage at temperatures

as low as 40°C, whereas the irradiated compounds did not shrink until temperatures

around 50°C were reached. This result indicates that crosslinking induced in the

molecular structure held the molecules in the drawn position. Changing the draw ratio

had minor effect upon percentage area shrinkage.

3.5 TENSILE PROPERTIES

The effects of draw ratio and irradiation on tensile strength at room

temperature and at 70°C are shown in Table 3.2. These properties had been previously

tested at BOOC, which was selected for higher temperature tensile testing of PVC by
many researchers(113.122,12S), but this temperature resulted in shrinkage of the drawn

samples. The testing was carried out at 70°C to reduce this problem, since it was

known that shrinkage was less at this temperature. The results showed that, for the

samples with the same formulation, tensile strength increased with draw ratio, as
reported before in several papers(S8-60,63-64). The tensile strengths of Fl samples were

higher than those of F2 both in undrawn and drawn specimens due to the addition of

TMPTMA, which acts as a plasticiser. It was observed that the irradiated samples gave

higher tensile strengths when compared with the unirradiated samples at the same draw

ratio. This effect was brought about by the crosslinked structure in PPVC. This effect

will be discussed in detail in Chapter 5.


PERCENT AGE AREA SHRINKAGE 11

100

80

80

"
DO 70
~"
~
.
.~

..et
fIl
.0

.""
..:
60

40

....
"DO
~
30

.."""
Il-<
20

10 0 Unirr. D.R.-1.3
c Unitr. D.R.-1.6

0 • Irr.
Irr . D.R.-l.3
• D.R.-l.6

·10

30 40 60 80 70 80 90 100 110 120 130

Temperature/Deg C

Figure 3.3 Percentage area shrinkage as a/unction o/temperature/or F2


Chapter 3 Preliminary Investigation 71

Table 3.2
Tensile Strength at Room Temperature and at 7(JOC

SAMPLE TENSILE STRENGTWMPa


BEFORE IRRADIATION AFfER IRRADIATION
ROOM 700 C ROOM 700 C
TEMPERATURE TEMPERATURE

F1 26.5 6.0 - -
SF1 (/,,=1.3) 34.0 10.3 - -
SF1 (/,,=1.6) 39.6 10.8 - -
F2 23.7 7.9 25.2 9.6

SF2 (/..=1.3) 31.0 11.7 33.3 13.5

SF2 (/,,=1.6) 35.1 13.4 38.4 15.2

3.6 WIDE ANGLE X-RAY DIFFRACTION (WAXD)

The WAXD pattern of drawn specimen F2 at the draw ratio of 1.3 is illustrated

in Figure 3.4. It can be observed that there are a number of distinctive peaks which do
not belong to PVC (WAXD trace of PVC was already shown in Figure 1.10). These

peaks were from the TBLS stabiliser. Hence, the x-ray diffraction technique cannot be

used to confirm the crystallisation occurring in these PVC compounds.

3.7 CONCLUSION

Crosslinking in stretched and unstretched PPVC can be induced by irradiating

samples with electron beam radiation. This is shown by the appearance of crosslinked

structures or gel content in irradiated samples. Crosslinked stretched samples gave

higher tensile strengths and lower percentage area shrinkage values than the stretched
r WAX» ~
100.---------------------------~----------------------------__,

20+-------------,--------------r-------------.-------------,~
8 18 38

Figure 3.4 X-ray diffraction pattern for stretched PPVC sample F2 at the draw ratio of 1.3
Chapter 3 Preliminary Investigation 73

samples without irradiation of the same formulation. Therefore, by introducing


crosslinking to drawn PPVC the properties of this material can be improved. Having
established the feasibility of this approach more detailed studies were carried out.

These are reported in Chapters 4-6.


Chapter 4 A Suitable Formulation and Crosslinking Conditions 74

CHAPTER 4

RESULTS AND DISCUSSION

II SELECTION OF A SUITABLE FORMULATION AND CROSSLINKING CONDITIONS

4.1 INTRODUCTION

Crosslinking of the oriented PVC compound (F2) containing TMPTMA as the

crosslinking agent and TBLS as the stabiliser was discussed in Chapter 3. It was found

that electron beam radiation promoted crosslinking in stretched PVC samples. The

formulation of the PVC compound studied in chapter 3 was not suitable for studying

the effect of orientation by using W AXD because some of the peaks arising from

TBLS coincide with several of those from the PVC itself. No attempt has been made

to optirnise formulation F2 for use with electron beam radiation.

Stabilisation of the irradiated formulation is very important, since it affects the

colouration, crosslinking efficiency and physical properties of the samples. Several

publications(lo3.I04) have documented the effects of stabilisers upon radiation

crosslinking of PVC compounds. The stabilisers investigated were of the tin group, the

barium-zinc group and the lead group. The lead group, e.g. TBLS and DBLS, was

found to be the most effective in the formation of crosslinked structures, but the tin

and barium-zinc groups gave better colour stability.

The aim of this part of the programme was to find a suitable formulation to

study the crosslinking of oriented PVC compounds. The lead stabilisers, namely

norrna1lead stearate and DBLS, and tin stabilisers, namely Stanclere Tl86, Stanc1ere
Chapter 4 A Suitable Formulation and Crosslinking Conditions 75

Tl84 and Stanclere TL, were used in the formulations prepared for irradiation
crosslinking. The effects of the amounts of each additive, i. e. TMPTMA and stabiliser,
and irradiation doses were studied to find out suitable conditions for the next
experiment.

The study was divided into two parts. In the first part, sections 4.2 to 4.5,
formulations F3 to F13, S2, S4, S6, and T2 to Tl 0, shown in Table 2.3, were used in
sheet form (undrawn samples) with thicknesses in the range 0.2mm to O.3mm. The
effects of the stabiliser type, TMPTMA level and irradiation dose upon the percentage
gel content, crosslink density and softening temperature were investigated. Specimens
with different stabilisers were examined using W AXD to ensure that the stabiliser
would not mask the x-ray diffiaction pattern from the PVC. The heat stability of each
formulation was also determined. The stabiliser found to be most suitable was then
employed in the second part ofthe study, outlined in section 4.6, in which the effects
of stabiliser concentration and radiation dose upon the properties of drawn samples
were determined. Drawn samples of formulations S2, S3, and S4 were used at draw
ratios in the range 1.5 to 1.6; the thicknesses of these ranged from 0.15mm to 0.20
mm.

4.2 EFFECT OF STABILISER

Initially three powder stabilisers, normal lead stearate, DBLS and Stanclere
Tl86 were used in this investigation. Two liquid stabilisers, Stanclere Tl84 and
Stanc\ere TL were introduced the later stages of the work specifically to study WAXD
as explained in section 4.2.5. The formulations employing these stabilisers are shown in
Table 2.1. Normal lead stearate was used in F3-F4; a mixture of normal lead stearate
and DBLS was used in F5; samples F6-F8 contained DBLS stabiliser at various levels;
Chapter 4 A Suitable Formulation and Crosslinking Conditions 76

Stanclere T186 was used in F9-Fll; Stanclere TL and Stanclere T184 were used in

F12 and F13, respectively. All the stabilisers described in this paragraph were effective,

since the irradiated samples showed no signs of discolouration. The experimental data

showed the effect of stabiliser upon the following factors: percentage gel content; oven

heat stability; softening temperature and WAXD.

4.2.1 Percentage Gel Content

The relationships between stabiliser type and percentage gel content, for the

formulations studied, are presented in Table 4.1. In the unirradiated state, all the

formulations were completely soluble in THF. After irradiation, F3 and F4 gave lower

percentage gel contents in comparison with the other formulations. The mixture of

normal lead stearate and DBLS used in F5 produced better results than normal lead

stearate alone. The highest percentage gel content was found in F8, which was

stabilised by DBLS, and hence DBLS was the best additive in the group of stabilisers

given in Table 4.1. Formulations F6, F7 and F8, using DBLS at levels of 4, 6 and 8phr

respectively, showed increased gel contents with DBLS concentration. It can be

concluded that at higher DBLS levels, i.e. in the more stable system, the crosslinking

efficiency was optimised. In formulations using Stanclere T186 it was observed that

the higher the stabiliser content, the lower the percentage gel content in irradiated

specimens. F12 stabilised with Stanclere TL showed a reasonable gel content; the gel

content ofF12 was found to be 43.6%. The formation of crosslinked structures in F12

was found to be less extensive than in the formulations stabilised with Stanclere T186

andDBLS.
Chapter 4 A Suitable Formulation and Cross/inking Conditions 77

Tab/e4.1
Percentage Gel Content and Softening Temperature

for Uni"adiated and i"adiated PPVC Formulations F3-F12

SAMPLE %GEL CONTENT SOFTENING


TEMPERATURE
f'Q
unirr. irr. unirr. irr.

F3 (4phr normal Pb stearate) 0 21.0 131 175


F4 (6phr normal Pb stearate) 0 23.7 137 175

F5 (3phr normal Pb stearate 0 46.9 141 171


+3phrDBLS)

F6 (4phr DBLS) 0 52.3 140 179


F1 (6phr DBLS) 0 54.4 136 178
F8 (8phr DBLS) 0 67.5 138 180

F9 (4phr Stanclere Tl86) 0 59.3 136 174


FIO (6phr Stanclere Tl86) 0 51.7 138 174
FIl (8phr Stanclere Tl86) 0 47.4 132 172

FI2 (4phr Stanclere TI..) 0 43.6 133 174

These results show good agreement with Hell et aI.< 10]) who found that the use

of basic lead stabiliser permitted the formation of high levels of crosslinking, but tin

stabiliser strongly inhibits the irradiation crosslinking process.

RodrigueZ(125) in a study of aminosilane crosslinking of PPVC also found that

organotin stabiliser containing PPVC samples gave lower gel contents than a
formulation stabilised by basic lead, barium, cadmium or zinc stabilisers. The
Chapter 4 A Suitable Formulation and Crosslinking Conditions 78

formulations containing tin had good resistances to premature crosslinking, i.e.

crosslinking was kept to a minimum until the crosslinking activation process was
carried out. The author explained that the reactivity of PVC with the stabiliser is higher

than that with the aminosilane, and therefore the grafting reaction of the aminosilane is

less extensive.

In systems containing lead stabilisers, the main stabilisation mechanism is

thought to be by the neutralisation of hydrogen chloride<ISI). This is supported by the

fact that lead chloride is formed in lead stabilised PVC materials during their heat
treatment and service<IS2). The effectiveness of the stabilising action of the lead

compounds depends upon the amount oflead in the stabiliser. DBLS is a mild external
lubricant as well as a stabiliser; normal lead stearate is similar to DBLS but provides

greater lubricity and a lower stabilising strength, which can be explained: DBLS

[2PbO.Pb(02CC17H3s)21 contains a considerably higher percentage lead content than


normal lead stearate, as shown in Table 2.2; this implies that DBLS gives better

stabilising performance through hydrogen chloride scavenging. Normal lead stearate


also has limited compatibility with PVC(ll3).

In conclusion, for the lead stabilisers the greatest gel contents were found in

formulations F9, FlO and Fll, containing DBLS; the formulation with the highest

stabiliser concentration (F1I), and hence the most stable compound, also gave greatest
gel content, as seen in Table 4.1. Apparently the degradation reactions taking place in

the formulations with lower stabiliser concentrations limit the effectiveness of the

crosslinking process. For the same reason, F5 that was stabilised by a mixture of
normal lead stearate and DBLS gave a higher gel content than F3 and F4, but the gel
content ofFS was found to be lower in comparison to F9, FIO and FIl.
Chapter 4 A Suitable Formulation and Crossfinking Conditions 79

Rn SnX(4-n) is the general chemical formula of organotin compounds, where R

IS an alkyl group (normally butyl or octyl) and X is a saturated or unsaturated

carboxylate, mercaptide or mercaptide ester such as a mercapto-acetate or a mercapto-

propionate. It was first noticed by Frye et al. (1S4) that the X component of an organotin

stabiliser became chemically bound to the polymer during the thermal ageing of

stabilised PVC. Klemchuk(155) studied the reactions of organotin compounds using

models compounds in place of PVC. The author used 4-chloropent-2-ene and 2-

chloro-2-metyl butane as the allylic and tertiary chloride models. The results showed

that organotin stabilisers reacted instantly with the allylic chlorine atom. This indicated

that the stabilisers functioned not only as an acceptor of hydrogen chloride but also

replaced the allylic chloride formed by dehydrochlorination. This reaction eliminated

further hydrogen chloride formation.

2-Ul=UI-rn-+R2snX2--~ 2-Ul=UI-CH-+R2SnOZ ····4·1


I I
a x

The high effectiveness of the stabilising action of organotin compounds can be

explained by their ability to suppress free radical chain processes. Dibutyltin stabilisers

were shown to lower the degree of radiation-induced grafting of styrene and

acrylonitrile onto PVC and it was concluded from ESR studies that they inhibited the
free radical reaction(IS6). Mori et al.(lS7) also found that organotin stabilisers were

effective in the deactivation of radicals. It was mentioned in section 1.7 the irradiation

crosslinking reaction starts with radical formation, and hence this stage can be

interrupted by the action of the tin stabiliser. It can be concluded that this results in the

low level of gel formed in formulations in which they were used, compared with

samples employing DBLS. The formulations with organotin stabilisers (Stanclere Tl86

in F9 FIO and FIl; Stanclere TL in FI2), however, gave higher gel contents than F3
Chapter 4 A Suitable Formulation and Crosslinking Conditions 80

and F4 that were stabilised by normal lead stearate, This result shows that the

formulation stability conferred by the organotin compounds limits the negative effects
that the degradation reactions have upon the crosslinking mechanism; the benefit of the

extra stability gained outweighs the hindering effect that organotin stabilisers have
directly upon the crosslinking reaction,

The irradiated sample containing 4phr Stanclere T1B6 (formulation F9) had a

greater gel content than the formulation employing 4phr Stanclere TL (F12), as a
result of the greater stability conferred to the system by the action ofT1B6(lS8-IS9),

4.2.2 Softening Temperature

A TMA 'softening temperature' was obtained to assess the increased resistance

to flow caused by irradiation, These temperatures were obtained from the experimental
traces as shown in Figure 4,1 for F12 and irradiated F12(IF12), The curves have been

offset to make them clearer, The softening temperatures of unirradiated and irradiated

F3 to F12 are listed in Table 4, I, As expected in all samples the softening temperatures
of the irradiated samples were higher than those of unirradiated samples. It is

interesting that all the irradiated samples had softening temperatures in the narrow
range of between 172°C and IBO°C, but the spread of their gel contents was
considerable (in the range of 21.0 to 67,5%), It can be seen that the compounds

stabilised with the same stabiliser at different levels show very similar softening

temperatures, Slight differences in softening temperatures are detected in formulations


containing different stabilisers, Compounds containing DBLS, F6 to FB, soften at

higher temperatures than compounds stabilised by tin stabiliser, F9-F 12, It is suggested
that different types of network structure are formed under the varying stabilising

conditions, It is possible that F6 to FB have network structure with higher numbers of


THERMOMECHANICAL ANALYSIS 11

......-------............ Softening
temperature g
p .§
e
n
e
t
/ ...~
";to..
r ~
a
t
/.., ~
."..
i Softening ~
temperature
0
n
~
~;:
i>'
§'
1 ~ Unirradiatcd Pll
I:l

9
;:s
I:l,

51
'"
:::-
--Irradiated P 12
,.,.
;:s.

~.

0 50 100 150 200 250 ~


;:s
Temperature/deg C ~
1:1'.
§
'"~
Figure 4.1 Penetration resistance for irradiated F12 and unirradiated F12
Chapter 4 A Suitable Formulation and Cross/inking Conditions 82

linkages between PVC chains. The gel contents played a significant role in shaping the

TMA traces in the temperature range 80°C to the softening temperature. The effect of

crosslinking on the TMA trace will be discussed later.

4.2.3 Ageing properties

The ageing properties ofF6 to F13 were assessed by placing specimens of each

of the formulations in an oven set at I77±O.5°C for one hour; any colour changes were

noted. F3 to F5 were not studied further since they showed low crosslinking efficiency.

The colours of samples before and after the tests are listed in Table 4.2. The distinct

change in colour for F6 to F8 indicated that DBLS provided poor resistance to colour

formation upon oven ageing. Stanclere T186 in F9 to FII and Stanclere TL in FI2

gave good performances since these samples only discoloured slightly. These results

are consistent with the results of Hell et al.(I03), who found that tin stabilisers gave

better colour stability than lead stabilisers. F13 stabilised by Stanclere T184 became

yellow during the test. Stanclere T184 thus had inferior stabilisation properties

compared with the other two tin stabilisers, and hence was not used in any further

tests.

Colour formation in PVC is directly affected by the extended polyene

sequences formed as a result of dehydrochlorination reactions. One of the most

important stabilising reactions of organotin stabilisers is the elimination of labile

chlorine atoms, as already shown in reaction 4.1. This elimination reaction can stop

further dehydrochlorination that increases the amount of polyene sequences. This

results in greatly improved thermal stability. In addition, organotin stabilisers can react

with double bonds in polyene sequences. An example of this was shown in reaction

4.2. The mercapto compounds that are released during the reaction between organotin
Chapter 4 A Suitable Formulation and Crosslinking Conditions 83

mercaptides and hydrogen chloride are able to add to double bonds(160.162); hence the

stabilising performance of organotin stabilisers is higher than that ofDBLS.

---l..... -CH-CH=CH-CH=CH-CH2-
I
....~.2

/S
i CgH17-0-CO -CH2

Table 4.2

Oven heat stability ofPPvc F6-FI3

SAMPLE ORIGINAL COLOUR COLOUR AFTER


HEATING

F6 (4phr DBLS) white translucent tan


F7 (6phr DBLS) white translucent dark tan
FS (Sphr DBLS) white translucent copper
F9 (4phr Stanclere TlS6) colourless transparent pale yellow
FIO(6phr Stanclere TlS6) colourless transparent pale yellow
Fl1(Sphr Stanclere TlS6) colourless transparent pale yellow
F12(4phr Stanclere TL) colourless transparent pale yellow
F13(4phr Stanclere TlS4) colourless transparent yellow

As mentioned in section 4.2.1, Stanclere Tl86 is the best thermal stabiliser

among stabilisers employed in this part of the prograntme. In this test the performances

of Stanclere Tl86 and Stanclere TL appeared very sintilar. It would be expected that a

greater level of differentiation may be obtained if the heating time was longer. The

stabilising action of dibutyltin dilaurate (Stanclere TL) and dibutyltin


Chapter 4 A Suitable Formulation and Crosslinking Conditions 84

bis(dodecylmercaptide), which has a similar structure to Stanclere T184,

(C4H9hSn(SCH2C02R), were found to be similar<lsSl. The oven heat stability of the

formulation containing Stanclere T184 was slightly poorer than the formulation

employing Stanclere TL. The reason for this is not clear, as the stabilising action of the

organotin stabilisers is complex and many factors are involved in the system. A

thorough search of available literature has not elucidated the reason for the action of
the Stanclere TL stabiliser; published findings are conflicting<lss,163. 164l.

4.2.4 Wide Angle X-ray Diffraction

The WAXD traces of PPVC samples with the three stabilisers, lead stearate,

DBLS and Stanclere T186 are illustrated in Figures 4.2 to 4.4, respectively. It can be

seen that all the traces contain distinct peaks that suggest that crystals of the stabilisers

or their reaction products are responsible. The positions of the peaks were found to

match with the x-ray diffraction patterns of the stabilisers alone. Some overlapping

peaks occurred in the regions 16° tol8° 29 and 24° to 25° 29 that were used to study

the change in the crystalline structures in PVC due to orientation<63-6 4l. Thus these

three stabilisers are not suitable for the purposes of this project.

To avoid crystal stabiliser interference liquid stabilisers were used. Two types

of liquid tin stabilisers, Stanclere TL and Stanclere T184 were selected to prepare PVC

samples according to formulation F12 and F13 in Table 2.1. As a result of the

discolouration of F13 in the oven heat stability test, this sample was no longer used.

The WAXD pattern of F12 in Figure 4.5 shows a very satisfactory trace without

interfering peaks. Consequently, Stanclere TL was the most promising stabiliser used

in formulation for the W AXD study.


55.------------------------------------------------------,

rn 45
·13
::>
.-~E 35

.-"E-~
.El 25

15+---------.---------.---------,---------~--------~--------~

10 15 20 25 30 35 40
Angle/o2theta
Figure 4.2 X-ray diffraction pattern for PPVC sample with lead stearate
[WAXD~
55.-----------------------~=======-----------------------~

45
.~
::>
~
.....
~ 35
>.
.....
.....
j 25

15+-------~------~------~------.-------~~~~
25 30 35 40
10 15 20
Angle/o2theta
Figure 4.3 X-ray diffraction pattern for PPVC sample with DBLS
85~--------------------------------------------------~--.

70

.~
::>
.§'55
.....
.0

~.c;-
..... 40

J
25

10+--------.---------,--------~------_,--------_,----~~

10

Figure 4.4 X-ray diffraction pattern for PPVC sample with stanclere T186
50~----~------------------------------------------------~

en
40
·s::>
~
.-;::
~ 30

~
j 20

10+---------r--------.--------~--------_r--------._------__4

10 15 20 25 30 35 40
Angle/o2theta

Figure 4.5 X-ray diffraction pattern for PPVC sample with Stanclere TL
Chapter 4 A Suitable Formulation and Crosslinking Conditions 89

4.2.5 The Preferred Stabiliser for this Study

From the results of the WAXD study it was found that Stanclere TL was the

only stabiliser that did not hinder the assessment of orientation by x-ray diffiaction.
This measurement was very important for the drawn samples in the subsequent

experiments. The non-discolouration of F12 in the ageing tests demonstrated that

Stanclere TL also provided effective stabilisation. The results of gel content analyses
and softening temperature measurements confirmed that a crosslinked structure was

created in this formulation. The tin stabiliser was found to inhibit the crosslinking
reaction, but this effect was kept under control by the lowest level of stabiliser possible

to maintain adequate stabilisation. In addition, gel formation was improved by other


factors such as increasing the irradiation dose and TMPTMA level. Hence, Stanclere

TL was selected as the stabiliser for the formulation used in the study of irradiation

crosslinking of oriented PPVC compounds.

4.3 EFFECT OF STABILISER CONTENT

The effect of stabiliser level on the irradiated samples was examined using
Stanclere TL at concentrations of 2, 4 and 6 phr in formulations S2, S4 (F12) and S6,

respectively. The level of TMPTMA was kept constant at 10 phr in all formulations.
The samples were used in the undrawn form. Before irradiation S4 and 86 were

colourless and transparent but 82 was slightly yellow. When exposed to an irradiation

dose of 4 Mrad 84 and 86 were not discoloured, but 82 became dark yellow.
September 2001

New photocopying cards


The Library has implemented a re-usable photocopying card system over
the summer.

These are for use on all the Library's copiers and can be purchased from
dispensers on Level Three of the Pilkington Library for £3.00. This includes
£1.00 for the cost of the card, £1.00 of photocopying credits and a £1.00
refundable deposit.

This card should be retained throughout your course and can be "topped
up' by using either the note or coin revaluers next to the card dispensers.
Users wishing to buy or revalue their cards using switch, should ask at the
Information and Enquiries Desk or Issue Desk on Level Three. Please note
that the minimum switch card transaction is £5.00.

The cost of copying is as follows:-

M black and white 5p M colour 70p


A3 black and white 10p A3 colour £1.40
Acetates 40p

Acetates for black and white copying are now available by selecting tray 2
on deSignated machines. Colour acetates should be purchased from
Information and Enquiries Desk.

Please note that some copiers on each level will still have an old card
reader attached to allow users to use up any outstanding units on their old
cards.
Chapter 4 A Suitable Formulation and Cross/inking Conditions 90

4.3.1 Percentage Gel Content and Crosslink Density

Gel contents and crosslink densities of 82, 84 and 86 are exhibited in Table 4.3

and Figure 4.6. No gel content was found in any of the unirradiated samples. It can be

seen that gel content decreased with the increase in 8tanc1ere TL level. This indicated

that the higher the 8tanclere TL concentration, the lower the amount of crosslinked

structures that can be produced. It was reported(ll3) that good high temperature tensile

strength can be achieved from crosslinked PVC with a gel content of 40% or over.

Hjertberg and Dah1(lIS) found that a relatively small amount of gel can be enough to

give rather large improvements in penetration resistance at temperatures in the interval

60 to 110°C, which perhaps is the most important for practical applications. The gel

content produced in these formulations would be expected to give rise to good high

temperature mechanical properties.

Table 4.3

Percentage Gel Content, Mc, Crosslink Densities and Softening Temperature

for Uni"adiated and I"adiated PPVC S2, S4 and S6

SAMPLE %GEL CONTENT


-M: CROSSLINK SOFTENING
(gImol) DENSITIES TEMPERATURE
(mol/g) l°C}
unirr irr unirr irr

S2 0 47.4 I.I59x104 4.3xlO-5 132 174


S4 0 43.6 1.283xl04 3.9xl0-5 133 174
(=FI2)
S6 0 33.2 l.34x104 3.7xlO-5 135 176
Chapter 4 A Suitable Formulation and Crossfinking Conditions 91

50 4.6
€iil %G.I Content
o Crossllnk Density

4.4
45

!!!
~
o
u 40
;;;
<!l
;F.

.><
.5
u;
35 o
o
3.6 U

3.6

2 3 4 5 6 7
Stonele,e TL Level/ph,

Figure 4.6 Gel content and crossfink density as a function of stabiliser level.

The results from swelling measurements showed good agreement with gel

content results. A decrease in molecular weight between crosslinks or an increase in

crosslink density was observed when the stabiliser loading was decreased.

The gel content can be improved by reducing the amount of this stabiliser. S2

gave the highest gel content, but discoloured after irradiation indicating that it was not

stabilising the system to a great enough extent. Stanc1ere TL in PVC at 4phr showed

good stabilisation properties. Considering all of the-results together, a formulation

containing 3phr Stanc1ere TL was introduced into the study of the irradiation of drawn

samples (section 4.6). It was expected to allow higher gel contents than S4, whilst still

maintaining stabilisation properties.


Chapter 4 A Suitable Formulation and Crosslinking Conditions 92

4.3.2 Thermomechanical Analysis

The softening temperatures of S2, S4 and S6 are presented in Table 4.3. Figure

4.7 illustrates the TMA traces of irradiated 83, S4 and S6, along with unirradiated F12

(S4) as a comparison. The softening temperature increased in irradiated samples as a

result of the presence of crosslinked structures. The softening temperatures of these

three formulations were similar although a difference between the gel contents was

observed. The presence of gel affected the penetration resistance in the TMA traces.

The TMA traces in Figure 4.7 show that 82 had the highest resistance until the

softening temperature was reached. S4 had a lower penetration resistance than S2 and

S6 had the poorest performance. It can be concluded that the higher the gel content,

the greater the penetration resistance.

4.3.3 Tensile Properties

The tensile properties of 82, S4 and S6 at room temperature and at 130°C are

given in Table 4.4 and 4.5 respectively. The room temperature tensile strength was

slightly increased in irradiated samples: e.g. the UTS of 84 was increased by 5.5%. The

increase ofUTS at 130°C was considerable. The increase in the UT8 of 82 was 80%

and for S6 it was 40%. Elongations at break at room temperature for the irradiated

samples were lower than those for the unirradiated samples of the same formulation.

This means that the ductility of the material decreased after crosslinking. At 130°C the

increase in elongation at break after irradiation was caused by the increased strerlgth of

crosslinked material. The linkages between polymer chains allow the neigi)boui'lng

polymer chains to slip over one another; consequently the tensile specimens are more

able to extend.
THERMOMECHANICAL ANALYSIS

p
e
n
e
t
r

...•.-----.
a
t
i
o ~ ......'-11-. _
n

y
........ Unirradi.t.d 1'12
-.- Irradiated 82
-4-lrradiated S4
- - Irradiated 56

o 60 100 160 200 260

Temperature/deg C

Figure 4. 7 Penetration resistance for irradiated IS2, IS2 and IS6


Chapter 4 A Suitable Formulation and Crosslinking Conditions 94

Figure 4.8 illustrates the influence of stabiliser level on VTS of the irradiated

samples both at room temperature and at 130°C. It was noted that VTS fell at higher

stabiliser concentrations. This result can be attributed to the effect of the crosslinked

network in the samples. The influence of the crosslinked network relates directly to the

VTS: the higher the gel content, the greater the strength of the material. Figure 4.9

presents the elongations at break of irradiated S2, S4 and S6 at room temperature and

at 130°C. At room temperature the effect of stabiliser level was not very clear, as all of

the tensile test results gave similar values. Elongation at break at 130°C increased to a

maximum and then decreased with increasing stabiliser level. Corresponding with the

low gel content in the crosslinked sample, S6 was the weakest material. The extent of

the network structures in S4 was higher than that in S6, so that S4 was stronger than

S6. The elongation at break of S4 was increased. The highest gel content in S2

restricted in chain mobility which resulted in a decrease of elongation at break.

Table 4.4

Tensile Strength and Elongation at Break at room temperature for Unirradiated

and Irradiated PPVC S2, S4 and S6

SAMPLE UTS AT ROOM %ELONGATION AT BREAK


TEMPERATURE (MPa)
uRirr. irr. unirr. irr.

S2 25.1 26.5 289 268


S4 25.6 27.0 294 251
(=FI2)
S6 24.2 25.3 2-18 242
------------- -----

Chapter 4 A Suitable Formulation and Crosslinking Conditions 95

Table 4.5
Tensile Strength and elongation at break at 130 'C for Unirradiated and

Irradiated PVC S2, S4 and S6

SAMPLE UTS(MPa) %ELONGATION AT BREAK

unirr. irr. unirr. irr.


, .. ':.
,
"l-'. . ..
82 0.5 0'.9 99 126
84 0.5 0.8 108 196
(=FI2) .,..
~'"
, :;.
'".' , ',,:: ..
86 0.5
--. 0.7. 109 105

29 1.3
• Room Temp.
o 130 D.ge
28
1.2

.
"-
::E
27
1.1
.
28 "-
'! ::E
-;"
....
~
25 1.0 .'"
0-
c
.
E
I- 24 0.9
0
'"
~

E -;
0
0
a:
-;
23
0.8
...
Cl>
:>
Cl>
I-
22
:>
0.7
21

20 0.8
2 3 4 5 6 7
Slanclere TL level/phr

Figure 4.8 Tensile strength at room temperature and at 130 'c as


a function of stabiliser level

.'
Chapter 4 A Suitable Formulation and Crosslinking Conditions 96
360 220
• Room Temp.
o 130 Doge
~
...:;;
:0

..'"
()

......
~ 340 180 0
0

...-......
e ~
e
o
a:

........ 300 140 .a


.a ...c
...c ..'"
,..
0

.
,g
iiI'
260 100
c
.2
w

W
c
o '"
'" 220 60
2 3 4 5 6 7

S1anclere Tl level/phr

Figure 4.9 Elongation at break at room temperature and at 130 CC


as a function of stabiliser leveL

4.4 EFFECT OF TMPTMA LEVEL

In order to study the effect of level TMPTMA, specimens of samples T2 to

T20 were prepared. Before being irradiated T2, TS and T1 O(F12) were colourless and

transparent but sample T20 was slightly yellow. Under an irradiation dose of 4 M.rad,

none of the specimens which were initially colourless were discoloured but the yellow

specimens became dark yellow.

4.4.1 Percentage Gel Content and Crosslink Density

Variations in percentage gel contents and crosslink densities with TMPTMA

concentration are shown in Table 4.6. Samples containing 2phr TMPTMA did not
Chapter 4 A Suitable Formulation and Crosslinking Conditions 97

yield sufficient gel for analysis. The gel content of unirradiated T20 is rather high when

compared with the other unirradiated samples. The reasons for this are that this sample

contains a very high concentration ofTMPTMA and it was prepared and kept at room

temperature for long a time before the tests were carried out. As a result crosslinking

occurred prematurely.

Table 4.6
Percentage Gel Content, Mc, Crosslink Densities and Softening Temperatures
for Uni"adiated and I"adiated PPVC T2-T20

SAMPLE %GEL CONTENT


-M: CROSSLINK SOFTENING
(gImol) DENSITIES TEMPERATURE
(moUg) (OCl

uuirr irr uBirr irr

TI 0 13.0 - - 140 173


T5 0 26.5 I. 858xlO 4 2.7xlO-5 139 175
no 0 43.6 l.282xlO4 3.9xlO-5 133 174
(=FI2)
TIO 26.8 55.6 0.605x10 4 8.3xlO-5 173 180

From Figure 4.10 it can be seen that the higher the TMPTMA content, the

higher the gel content and crosslink density. This implies that increased TMPTMA

concentration increases the efficiency of crosslinking. This effect was observed

previously by Nethsinghe and Gilbert(l12).


Chapter 4 A Suitable Formulation and Crosslinking Conditions 98

60 10

50

40
6
-""
DO

C
C
. E
'"
~

....,..
.!!.
0

.,...
0
_ 30 6 ~
Cl c

20
4
..
-'"
.5
0
~
0

10
o IIGII Contont
• CrolSUnk Don,lty
0 2
0 5 10 15 20
TMPTMA level/phr

Figure 4.10 Gel content and crosslink density as afunction ofTMPTMA level

TMPTMA homopolymerisation took place in the initial stage followed by

grafting to PVC to form the crosslinked structure<107-109). The increase in TMPTMA

level caused a greater amount of polyTMPTMA which in turn increased the number of

linkages between PVC chains; consequently a more effective crosslinking system was

achieved.

4.4.2 Thermomechanical Analysis

The softening temperatures ofT2, TS, TlO and T20 before and after irradiation

are listed in Table 4.6; none of the softening temperatures were significantly affected

by TMPTMA content except for T20. In the latter case an increase was caused by

premature crosslinking in the unirradiated specimen. The higher gel content in

irradiated T20 caused the higher softening temperature.


Chapter 4 A Suitable Formulation and Crosslinking Conditions 99

TMA traces showing the effect of increased TMPTMA concentration are

shown in Figure 4. 11. The effect of network structures can be seen in the traces

between about SO°C and the softening temperature. The penetration decreases with

increasing degree of crosslinking or TMPTMA level. The trace of irradiated sample

T20 shows a very small penetration until the softening temperature is reached, also

inferring that the amount of crosslinked structure in this sample is very high.

It can be seen that the traces for irradiated T2(IT2) and irradiated TS(ITS)

show an increase in the gradient towards the end of plateau region over the

temperature range 110°C-140°C in comparison to the trace of unirradiated F12. The

penetration resistance in this range is controlled by the physical network. The increase

in penetration resistance of IT2 and ITS is possibly attributable to the lowering of

crystallinity, which may be partially destroyed by the electron beam radiation. This

decrease in crystallinity in the irradiated materials was discovered by using DSC as

discussed in section 6.2.1. This effect, however, cannot be detected in the TMA traces

of the irradiated samples with higher gel contents e.g. ITlO, IT20, IS2, IS4, IS6, 14,16

and IS; neither is the effect seen in the TMA trace for the sample 12 (Figure 4.15) with

a lower gel content. It is suggested that in the samples with higher gel contents the

chemical networks can compensate for the reduction in crystallinity, therefore the

penetration resistance is maintained. The result for sample 12 depends on two factors.

Firstly, a lower irradiation dose was employed for 12. This might have caused less

damage in the physical network. Secondly, although its gel content is rather low, it

appears that the crosslinked network produced is quite dense, as shown by crosslink

density values S.7xIO-s (Table 4.6) and 2.7xIO-s (Table 4.9) for 12 and ITS,

respectively. These structures are responsible for the plateau region in TMA trace.
THERMOMECHANICAL ANALYSIS 11

p
e
n
e
t
r

- .....--.
a
t

o
•••••• --'HL_
n

1 -Ir-

-
Un irradiated P 12
Irradiated
-o-lrradiatcd
T2
T'
--+-Irradiated T 10
- 0 - Irradiated T20

o 50 100 150 200 250


Temperature/deg C

Figure 4.11 Penetration resistance/or F12, IT2, ITS, ITlO and IT20
Chapter 4 A Suitable Formulation and Crosslinking Conditions 101

4.4.3 Tensile Properties

Tables 4.7 and 4.8 present the tensile properties at room temperature and at
130°C for T2,TS, TlO and T20 before and after irradiation. As expected, the increase

in tensile strength by the effect of irradiation was slight at room temperature but
considerable at 130°C. The percentage elongation at break of the irradiated samples

was found to rise at room temperature; conversely a decrease in the percentage

elongation at break was noted when the test was performed at 130°C. The effect of
premature crosslinking in T20 can be seen clearly by the fact that the percentage

elongation at break was remarkably low. Figure 4.12 shows that the tensile strength of
the irradiated samples rose with increased TMPTMA level; this effect was much

clearer when the test was carried out at 130°C. At elevated temperatures the physical
network formed by the crystallites is partially destroyed, so that the strength of the

materials must depend upon the chemical network. The study of crystallinity by DSC
will be discussed in section 6.2.1.

Table 4. 7
Tensile Strength and Elongation at Break at room temperature for unirradiated
and irradiated PPVC T2-T20

SAMPLE UTSATROOM %ELONGATION AT BREAK


TEMPERATURE (MPa)
unirr. irr. unirr. irr.

T2 25.7 26.0 316 314


T5 25.3 26.5 314 280
T10 25.6 27.0 294 251
(=FI2)
T20 26.5 27.5 232 198
Chapter 4 A Suitable Formulation and Crosslinking Conditions 102

Table 4.8
Tensile Strength and Elongation at break at 130 cCfor unirradiated and
irradiated PPVC T2-T20

SAMPLE UTS(MPa) %ELONGATION AT BREAK

unirr. irr. unirr. irr.

T2 0.5 0.6 116 135


T5 0.4 0.7 96 174
TlO 0.5 0.8 108 196
(=F12)
T20 0.7 l.l 46 69

The plots of elongation at break of irradiated samples as a function of

TMPTMA level are shown in Figure 4.13. The difference between the two test
temperatures can be clearly seen. At room temperature the greater the TMPTMA

level, the lower the elongation at break. The decrease of room temperature elongation
at break with increased TMPTMA level implied that the irradiated PVC sample

became stronger and harder. The plot of elongation at 130°C against TMPTMA
concentration passed through a maximum, which corresponded to the sample with 10
phr TMPTMA. These results are similar to the results of Nethsinghe and Gilbert(112),

who explained that chain mobility is greater at higher temperatures. Elongation at

break increased in parallel to the increase in strength, but above 10 phr TMPTMA the
elongation at break decreased due to the reduction of chain mobility when the crosslink

density increases further.


Chapter 4 A Suitable Formulation and Crosslinking Conditions 103
1.4

28
.
.'"
a..

~
1.2

0..
.
•...:;;
~

28
1.0 U'"..
'"
E
!!
E ..
0
0
~

...•
0
l! 0.8

...•
Cl)

en :::>
24
:::>
0.8

• Room Temp.
o 180 DogC
22 0.4
0 5 10 15 20
TMPTMA level/phr

Figure 4.12 Tensile strength at room temperature and at 130 cCfor crosslinked
PPVC compounds as a function 0 TMPTMA level
380 240
• Room Tlmp.
o 130 DogC
:!
•... ...,.
~

320 200 ()
:0
0
E
!! 0
l2
E
280 160
...•
0
f!

...•..
od
l!!
ID

•"
od

oli 240 120


•"
0
0
';
.,.
'; "0
ijj
'" 200 80
"0
ijj '"
'"
180 40
0 5 10 15 20
TMPTMA leveUphr

Figure 4.13 Elongation at break at room temperature and at 130 cC for cross/inked
PPVC compounds as afunction of TMPTMA level
Chapter 4 A Suitable Formulation and Crosslinking Conditions 104

4.4.4 The selection of TMPTMA Level

In this study the gel content was improved by increasing the level ofTMPTMA

in the PVC formulations. The formulation with 20 phr TMPTMA was found to

produce some gel before the irradiation process took place. This occurrence may lead

to difficulties in further processing steps introduced into the procedure. The residual
unsaturation in irradiated PPVC samples which included TMPTMA in their

formulations was measured by Infrared Spectroscopy(lI2). The results showed that this

unsaturation could be attributed to the presence of unreacted double bonds of


TMPTMA. The percentage of remaining unsaturation in samples containing increasing

TMPTMA concentrations was found to be similar until the TMPTMA loading reached

10 phr. Between 10 phr and 20 phr TMPTMA the remaining unsaturation increased
proportionally with the radiation sensitiser level. The presence of unsaturation was

undesirable since it is known to promote oxidative degradation in the polymer which

reduces the service life of the crosslinked product, particularly when exposed to
ultraviolet light or elevated temperatures. 10 phr was therefore selected as the

optimum concentration ofTMPTMA.

4.5 EFFEcr OF IRRADIATION DOSE

In order to study the effect of irradiation dose, thin sheet specimens of sample

F12 were prepared. Irradiation was performed at doses of2, 4, 6 and 8 Mrad. None of
the irradiated specimens were discoloured.
Chapter 4 A Suitable Formulation and Crosslinking Conditions 105

4.5.1 Percentage Gel Content and Crosslink Density

The influence of irradiation dose upon gel content and crosslink density is

illustrated in Table 4.9 and Figure 4.14. It can be seen that an increased irradiation
dose at constant TMPTMA level produced an increased gel content, but crosslink

density was correspondingly decreased. Crosslink density was considerably reduced in

specimens 12 to 14, but fell only slightly between specimens 14 to 18. It has been
suggested(l12) that at an irradiation dose which is higher than the optimum dose, the

initial network formed by the crosslinked TMPTMA breaks down and the resulting
radicals formed react with more PVC molecules to give a more open structure. It is

not possible to conclude that the irradiation dose at 2 Mrad is the optimum dose for
this study, since the gel content in 12 was not high enough to modifY the mechanical

properties at elevated temperatures. Therefore the effect of irradiation dose on the

properties of the stretched samples with different levels of stabiliser was investigated
and will be discussed in section 4.6.

Table 4.9

Percentage Gel Content, Mc, Crosslink Densities and

Softening Temperature/or 12-18

SAMPLE %GEL CONTENT


-
Ill: CROSSLINK SOFfENING
(gImol) DENSITIES TEMPERATURE
(mol/g) (0C)

unirr irr unirr irr

12 - 22.1 O.871x10 4 5.7xIO·5 · 183


14 . 43.6 1.283xlO 4 3.9xlO-5 · 174
(=FI2)
16 - 57.0 1.416xl0 4 3.5xl0·5 · 175
18 . 71.2 l.504xl0 4 3.3xI0·5 · 174
Chapter 4 A Suitable Formulation and Crosslinking Conditions 106

80
o %Gel Content
e
• Crollllnk Density

60

E
D
E
o
u
'ii 40
'"'"
...
20
4
..
.E

"
l!
u

o 3

o 2 4 e 8
Irradiation dose/Mrad

Figure 4.14 Gel content and crosslink density as a function of i"adiation dose.

4.5.2 Thennomechanical Analysis

TMA traces showing the effect of increased irradiation dose are shown in

Figure 4.15. As expected the penetration resistance increased with the gel content and

irradiation dose. The trace of 18 showed the best performance as its gel content was

the highest. Although the crosslink density was found to decrease at irradiation doses

higher than two Mrad, it was found not to have much effect on the development of a

plateau in the TMA trace, however the softening temperature of 12 was higher than

those ofI4, 16 and 18, as shown in Table 4.9. The small amount of network structures

with high crosslink density in 12 caused the raising of its softening temperature.
THERMOMECHANICAL ANALYSIS 11.

p
e
n
e
t
r
a
t
i
.....---- ..............
o
n
--------

1 Un irradiated F12
-t:.-

---12
~14
~16
~18

o 50 100 150 200 250


Temperature/deg C

Figure 4.15 Penetration resistance/or 12,14,16,18 and F12


Chapter 4 A Suitable Formulation and Crosslinking Conditions 108

4.5.3 Tensile properties

Table 4.10 and Figures 4.16 to 4.17 show the influence of irradiation dose

upon tensile strength and elongation at break both at room temperature and at 130°C.

As expected the effect is more significant at higher test temperatures. The tensile

strength also increased with longer irradiation doses. This implied that the effect of the

gel content on this property had a greater influence than that of crosslink density. The

gel content increased with irradiation dose but crosslink density fell at larger irradiation

doses.

The elongation at break ofI2 at 130°C was slightly greater than that of the

same formulation in the unirradiated form due to the small amount of gel present in this

sample. Elongation at break markedly increased from 12 to 14 and then levelled off

over the range 14 to 18, even though the gel contents of each were much different (they

were 43.6, 57.0 and 71.2, respectively). This observation showed the combination of

the effects of gel content and crosslink density. If the effect of gel content alone was

considered, the plot would be expected to pass through a maximum in a similar manner

to the plot between percentage elongation at break at 130°C and TMPTMA content.

The decrease in crosslink density in samples exposed at higher radiation doses

permitted greater mobility in network structures which allowed the greater percentage

elongation at break.
Chapter 4 A Suitable Formulation and Crosslinking Conditions 109

Table 4.10
Tensile Strength and Elongation at Break at room temperature

and at 130 'C for 12-18

SAMPLE PROPERTIES AT ROOM PROPERTIES AT 130·C


TEMPERATURE
UTSlMPa %EB UTSlMPa %EB

12 26.5 237 0.6 115


14 27.0 251 0.8 196
(=F12)
16 28.0 245 1.0 178
18 27.0 226 1.4 176

30

1.4

.. 28 1.2

.
D..
:E
~
~
.
0..
:E
d
;;
.
E
Q,
28
1.0 U
co
c
.
.... C>
~
E 0.8
0
0
.,...."Ri
-..
cc

rn
....
24
0.8
::>

::>
• Room Temp.
D 130 o.ge
22 0.4
0 2 3 4 5 8 7 8 9
Irradiation Dose/Mrad

Figure 4.16 Tensile strength at room temperature and at 130'C/or crosslinked

PPVC compound as a function of i"adiation dose


Chapter 4 A Suitable Formulation and Crosslinking Conditions 11 0
340

200
:!!
"
:;
...:;;
E
300 0
..
c"
...
co
12
0

E 160 :;;
.....
0
0
c: 260
:;
.....
co
.l;
:;;
.l;

..ill
c
:; .!!
120 :;;
c 220 c
.!!
:;
co
c
ill • Room Temp.
'"
'" 180
" 130 D.ge
80
0 2 3 4 5 B 7 8 9
Irradiation Do••/Mrad

Figure 4.17 Elongation at break at room temperature and at 130 cC for crosslinked

PPVC compound as afunction ofi"adiation dose

4.6 STUDY OF ORIENTED SAMPLES

In this section the work was focused upon the combined effect of stabiliser

level together with irradiation dose on the properties of crosslinked oriented samples

with draw ratio in the range of 1.5 to 1.6. As stated in section 4.3.1 the gel content can

be improved by keeping the stabiliser level as low as possible. From section 4.5.1 it

was found that the higher the irradiation dose used, the greater the gel content that was

formed. A compromise between these two variables was sought, as both affect the

stability of the system. TMPTMA at a concentration of 10 phr was used in this

experiment. Levels of stabiliser at 2, 3 and 4 phr (samples S2, S3 and S4 in Table 2.1)

and irradiation doses of 3, 4 and 6 Mrad were chosen. Percentage gel contents were

measured together with tensile properties at 100°C. The temperature of 100°C was

selected instead of 130°C in order to reduce the amount of shrinkage of the drawn
Chapter 4 A Suitable Formulation and Crosslinking Conditions 111

samples and reserve some part of the crystallites which melt at temperatures higher

than 100°C. These crystallites retard the plastic flow behaviour, leading to more

precise results in tensile tests. The tensile strength data in Tables 4.5, 4.8 and 4.10 are

very low because at 130°C the majority of the crystallites melt and the samples become

soft.

Table 4.11

Percentage gel content and tensile strength at 100 cC

for irradiated drawn S2, S3 and S4 at the dose of 3, 4, and 6Mrad.

SAMPLE %GEL CONTENT UTS AT 100°C (MPa)


(1..=1.5-1.6) 3Mrad 4Mrad 6Mrad 3Mrad 4Mrad 6Mrad

S2 30.1 37.0 42.4 5.2 5.6 6.0


S3 28.1 34.9 39.2 4.9 5.1 6.4
S4 27.0 32.6 37.0 5.0 5.1 6.3

The results of these tests are displayed in Table 4.11 and Figures 4.18-4.19.

The irradiation dose at 6 Mrad showed the greatest effect both in gel formation and in

improvement of tensile strength at 100°C. The gel content decreased with an increase

in stabiliser content at all irradiation doses. Tensile strength also decreased with

increased stabiliser concentration at the irradiation doses of 3 and 4 Mrad. After the

specimens were exposed at 6 Mrad, the lowest tensile strength was found in S2 and the

highest one was found in S3. This can be attributed to the stabilisation effect. It is

possible that the molecules in S2 broke down at this irradiation dose, due to the

inadequate concentration of stabiliser. From these experimental observations the

stabiliser level at a concentration of 3phr was selected in order to maintain the desired
Chapter 4 A Suitable Formulation and Crosslinking Conditions 112

50

-.
c
E
40

.0
()

<!J

'"
30

o 3 Mrad
• 4 M,"d
+ e Mrad
20
1 2 3 4 5
Sta.cte,e TL leveVph,

Figure 4.18 Gel content as afunction of stabiliser level

,...
8

....
rL

0-
Q
0
$!
... 5
'"~
o 3 M,"d
• 4 Mrad
+ " Mrad
4

2 3 4 6
Stancle,e TL level/ph,

Figure 4.19 Tensile strength as afunction of stabiliser level


Chapter 4 A Suitable Formulation and Cross/inking Conditions 113

stabilisation, whilst still enabling crosslinking to occur using an irradiation dose of

6Mrad.

4.7 CONCLUSION

The liquid tin stabiliser Stanc1ere TL was found to be the most suitable
stabiliser for PVC in the study of crosslinking of oriented PPVC compounds. The
optimum concentrations of TMPTMA and stabiliser were 10 phr and 3 phr
respectively. An irradiation dose of 6 Mrad was found to provide satisfactory

crossJinking conditions.
Chapter 5 Properties 114

CHAPTERS

RESULTS AND DISCUSSION

III PROPERTIES OF CROSSLlNKED ORIENTED SAMPLES

5.1 INTRODUCTION

The experimental work outlined in chapter 4 showed that formulation S3 and

an irradiation dose of 6 Mrad provided the optimum formulation and post processing

conditions respectively; this system was employed as the basis for the work in this

section. To study the effect of plasticiser content on the properties of irradiated

samples, formulation P25 (which contained a low plasticiser concentration) was also

used in this section. The glass transition temperature (Tg) of sample S3 and P25 were

-21°C and _5°C, respectively. The values of Tg were obtained by thermomechanical

analysis (TMA) using a DuPont 990 thermal analyser, at heating rate of 10°C

The aim of this part of the research programme was to examine the influence of

crosslinked structures and/or oriented structures upon tensile and impact properties.

Additionally the effect of sample thickness upon gel formation was investigated,

because the drawing process reduces sample thickness, which in turn may affect the

result of the irradiation process.

5.2 EFFECT OF SAMPLE THICKNESS

When a film sample is irradiated it has been shown that the maximum dose

occurs within the body of the material and not at the incident surface. This is due to
Chapter 5 Properties 115

the elastic collisions with atomic nuclei which tend to scatter the incident electrons in
all directions. Wide-angle elastic scattering causes the build-up in the dose in the body
of the material close to the sample surface (the distance from the surface is controlled
by the sample density) and a gradual reduction in the dose beyond the maximum
point<168l. Figure S. t<l69l(a) shows the variation in electron beam radiation dose with
product thickness. The dose distribution through the product can be improved by
irradiating the sample from two directions, as shown in Figure S.l(b).

Dose I


Electrons~_

Product thiclmess
(a) Monodirectional irradiation

Dose


Electrons-_ <---Electrons

Product thickness
(b) Two sMed irradiation

Figure 5.1 (a) The dose distribution from a mono-directional i"adiation(I) of


product with mono-energetic electrons (b) The effect of a two-sided(I+lI)
i"adiation of a thicker product

The applicability of the established theory described above to the system under
investigation in this work was examined. The effects of specimen thickness of moulded
sheets and undrawn samples of formulations S3 and P25 were studied. The results
were related to gel formation and tensile properties.
Chapter 5 Properties 116

5.2.1. Percentage gel content

The relationships between specimen thickness of undrawn samples 83 and P25


and gel content is shown in Figure 5.2 and Table 1.1 in Appendix 1. It was found in

both formulations that gel content decreased with increasing sample thickness. The
dose of electron beam radiation in the middle of sample decreases with increasing

sample thickness, as shown in Figure 5.1(b); it was found in section 4.5.1 that the

formation of gel was enhanced at higher radiation doses, and hence in the thicker
samples the formation of cross1inked structures is reduced.

80
III ~OBL 83
• t;OBL P25

I!J
50

00

40 00
~
J!!
c 00
0
0
'0
'"'" 30

20

10

0.1 0.2 0.3 0.4 0.5


Sample Thickness/mm

Figure 5.2 Effect ofsample thickness on % gel content for SJ and P25

Gel formation in 83 was found to be more sensitive to sample thickness than

that ofP25. The differences in behaviour between these two samples are related to the
different plasticiser contents in each formulation. This result shows good agreement
with Kojima et al. (104) who found that the gel content ratios in irradiated PVC were
2001

Research students· Borrowing from other


East Midlands University Libraries
The University Library is participating in a trial scheme to extend borrowing right!
for research students (PhD or MPhil students) to other East Midlands institutions
This scheme will run from August 1st 2001 to July 31st 2002 in the first instance.

The following institutions are participating:

Bishop Grosseteste College


De Monltort University
Derby University
Nottingham Trent University
University of Leicester
University of Lincolnshire and Humberside
University College Northampton
University of Nottingham

Under the terms of the scheme, research students may now use these librarie!
for both reference and borrowing purposes. Academic staff are already entitled tc
apply for these services at the participating libraries.

To join, all staff and researchers must first complete an introductory fom
available from the Issue Desk of the Pilkington Library. This will be stamped anc
should then be taken to the libraries you wish to use together with a curren
Loughborough ID card. Here, you will be issued with an extemal membershi~
card, which will be valid until 31st July 2002.

Please note that Loughborough users will not be entitled to access electronic
databases at other libraries and will be required to observe the regulations of thE
host libraryllibraries.
Chapter 5 Properties 117

larger when the plasticiser level was increased. This effect was also found by Bowmer
et a1.(I09) in the study on the effect of diundecylphthalate (DUP) on the radiation
crosslinking of PVC with TMPTMA. Their results showed that the introduction of
DUP, as a plasticiser, into the mixtures enhanced TMPTMA polymerisation,
TMPTMA grafting and the rate of the PVC crosslinking reaction. It is also possible
that the dissimilar performances of 83 and P25 are related to the formation of unlike
types of crosslinked networks in each material, due to the changed crosslinking
reaction environment in each formulation.

5.2.2. Tensile properties

The shapes of the tensile stress-strain curves were similar to those found in
section 4.3.3 and 4.4.3; this behaviour is directly related to the material gel content.
Figure 5.3 and Table 1.2 present the variations in tensile properties at 100°C with
specimen thickness. The results show that tensile strength rises with an increase in gel
content in the sample. The plot of elongation at break against sample thickness, shown
in Figure 5.3, contains a maximum corresponding to a sample thickness of about
O.3mm. The portion of the curve up to a sample thickness ofO.3mm may be explained
by the following argument: in the thinnest specimen, the most extensive crosslinked
network is formed and as a consequence the movement of polymer chains is highly
restricted. This results in a low tensile elongation at break. As sample thicknesses
increase, the extent of crosslink formation in the materials decreases, which is detected
by the lowering ofthe measured gel contents; since there are fewer tie points between
adjacent molecules, neighbouring polymer chains are freer to slip over one another and
hence the tensile specimens are more able to extend. As sample thicknesses increase
over the range 0.3mm to 0.5mm the proportion of crosslinking sites, which is directly
related to gel content, in the test specimen becomes so low that there are insufficient
Chapter 5 Properties 118

forces holding the PVC chains together and the polymer molecules rapidly slip over
one another; this leads reduced elongations. Similar results were also found in the
sample containing 25phr mop, as shown in Figure 5.4

5.2.3. Selection of Sample Thickness

It can be seen clearly that the sample thickness has a large influence upon

crosslink formation; the thicker the sample, the lower the gel content and hence tensile
strength. To eliminate this effect, drawn and undrawn samples were produced at the
same thickness. A very small sample thickness was employed to enhance gel content
formation. Practically it is only possible to produce even specimen thicknesses with
good precision up to the nearest tenth of a millimetre in PVC moulded sheets. It is
more difficult to control sample thickness for drawn samples, as the stretching step in
the sample preparation reduces thickness further. To tackle this problem a number of
samples were prepared from which were cut mechanical test specimens; specimens of
very similar thicknesses were employed for comparative work. The thicknesses of test
specimens were in the range ofO.21mm to 0.22mm.

5.3 EFFECf OF DRAW RATIO

As stated in section 1.9, draw ratio is the most significant variable affecting the

mechanical properties of the oriented PVC samples. In this section, the investigation
was concentrated on the effect of draw ratio upon gel formation and the changes of
tensile and impact properties of samples after irradiation. Sample S3 and P25 were
prepared and stretched to different draw ratios, followed by electron beam irradiation
at a dose of 6 Mrad. To limit the influence of thickness variations upon the mechanical
Chapter 5 Properties 119

., UTS
800

• "EB

8
"c'""
.
0- 500 <>
~
'"0- 0;
c'"
" ......
-
<>
<>
0; 5
ol;
0;
c
....
Cl)

:::>
400
..
,g
co
c
0
iii
>I'

4 300

0.2 0.3
Sample Thickness/mm

Figure 5.3 Effect of sample thickness on tensile properties at 100 cCfor S3.

5.8

5.8

5.4
.:!.
..
0-
5.2
"c..
<> 5.0
~
0;
Cl) 4.8
....
:::>
4.8

4.4

4.2 300

0.2 0.3 0.4 0.5


Sample Thlckn.ss/mm

Figure 5.4 Effect of sample thickness on tensile properties at 100 cC for P25.
Chapter 5 Properties 120

properties, all test specimens were cut from drawn and undrawn samples with

thicknesses in the range 0.21mm to 0.22mm

5.3.1. Percentage gel content

Table 5.1 displays the effect of draw ratio on the gel contents of irradiated

samples offormulations containing 46.5 phr DIOP (53) and 25phr DIOP (P25). It can

be seen that the highest gel content was found in undrawn sample 53, whilst similar gel

contents were measured in samples with draw ratios in the range I. 3 to I. 7. This

implies that the efficiency of the crosslinking reaction taking place in the undrawn

samples is higher than in the drawn samples. After sample drawing and annealing in the

stretched state, the formation of small crystallites locks the oriented polymer chains

into position, which leads to reduced chain mobility; the crosslinking reaction was less

extensive in the drawn sample, resulting in reduced gel formation. This result shows

good agreement with Nikolova and Mateey(170) in the study into irradiation of oriented

LDPE films. They found that the orientation of polyethylene films decreased the

formation of networks induced by irradiation. The gel content of drawn samples was

found to be independent of draw ratio in the range studied, although the mobility of

chains related directly to draw ratio. It is possible that the draw ratios employed in this

work are not high enough to play a significnt role in the reduction of chain mobility.

It can be seen that for samples with lower plasticiser contents, the effect of

orientation is insignificant; the gel contents in the drawn and undrawn samples with the

lower plasticiser contents over the draw ratio range 1.4 to 1.9 were similar. Although

the mobility of chains in the oriented samples was expected to be lower than before

stretching, the difference in gel formation was not distinctive. Over the range of draw
Chapter 5 Properties 121

ratios studied, it is suggested that the reduction of the mobility of polymer chains by
orientation had a very small effect upon the crosslinking reaction.

Table 5.1
Effect of draw ratio on % gel content

FORMULATION DRAW RATIO % GEL CONTENT

S3 1.0 44.01
(46.5 phr mOP) 1.26-1.28 37.19
1.39-1.41 36.93
1.52-1.54 37.32
1.66-1.70 3839

P25 1.0 29.94


(25 phr moP) 1.34-1.40 30.84
1.62-1.64 30.86
1.82-1.86 32.97

5.3.2 Tensile Properties

Figure 5.5 and 5.6 show typical stress-strain curves obtained in tensile tests of
specimens of S3 and P25 respectively. The ultimate tensile strength of both
formulations at both temperatures falls in the sequence:

UTS unirr. undrawn. <UTS irr. undrawn <UTS unirr. drawn < UTS irr. drawn
Chapter 5 Properties 122

The plasticisers used in both formulations examined in this work resulted in

rubber like physical performances of the materials under tensile test conditions. As
expected, the UTS of unirradiated undrawn P25 was found to be higher than that of

S3. Tensile strength is generally reduced by the addition of plasticiser since the stress
developed is reduced because of the lower molecular cohesion(I43). None of the curves

for S3 displayed in Figure 5.5A and B show clearly defined yield points. The results

show that orientation results in an increase in modulus at 100% strain (which is

referred to as 100% modulus). The crosslinked structures also improve the 100%

modulus in both drawn and undrawn samples. Similar performances were observed in
the tensile properties of P25 at room temperature (see Figure 5.6A). The yield points

observed in the tensile tests performed on P25 at room temperature are more

pronounced than those in all the other plots. When the tensile tests were performed at
100°C, the 100% modulus of irradiated drawn P25 was found to be lower than that of

the corresponding unirradiated drawn sample. The reasons for this are as yet unclear.

The results of tensile strength and elongation at break measurements at room

temperature and at 100°C of S3 and P25 are given in Tables I3 and 14 and Figures 5.7
to 5.10. Tensile strength was found to be enhanced at increased draw ratios. The
explanation was that biaxial stretching raises the number of crysta11ites lying in the

plane of the film; x-ray diffiaction studies reported in section 6.3 support this

argument. The number of crystallites was found to increase with increasing sample
draw ratio. These crystallites contribute to the mechanical property modification in the

plane of the film which is higher in the more highly oriented sample, that is at larger

draw ratios. The increase in room temperature tensile strength produced by the effect
of irradiation for both formulations was small. A significantly improved tensile strength

of the irradiated materials over the unirradiated samples can be seen when tensile tests
were performed at 100°C. It is concluded that the strength at room temperature is
Chapter 5 Properties 123

40
(A)

(4)
30 (3)

(2)

.
!i
(I)
';f 20

!!
;;;

10
(I) Unirr. Undrawn
(2) Irr. Undrawn
(3) Unlrr. Drawn(D.R.-I.3)
(4) Irr. Drawn(D.R.-I.3)
o
o 100 200 300
Straln/1I

7
(8)
(4)
8

5
(2)

~ _ _-(3)
3

~ _ _- (I)
2

(I) Unlrr. Undrawn


(2) Irr. Undrawn
(3) Unlrr. Drawn(D.R.-I.3)
(4) Irr. Drawn(D.R.-1.3)
o
o 100 200 300 400 500
Straln/1I

Figure 5.5 Stress-strain curves ofS3 (A) at room temperature and (B) at 100 cC
Chapter 5 Properties 124

60
(A)
(4) (3)

SO

(2)
40
(I)

"-
.
...'"•..' 30

lE
20

10 (1) Unlrr. Undrawn


(2) Ir •. Undrawn
(3) Unlr •• D.awn(D.R.-l.3)
(4) Ir •. D.awn(D.R.-I.3)
o
o 100 200 300
SI,al_I"

7 (B)
(3) (4)
e
(2)
5

..
Go
4 (I)

'..."...'
s
iil
2

(1) Unlr •• Undrawn


(2) Irr. Undrawn
(3) Unlr •• Drawn(D.R.-I.3)
(4) I ••• Drawn(D.R.-l.3)
0

0 100 200 300 400


StralnJ"

Figure 5.6 Stress-strain curves of P25 (A) at room temperature and (B) at 100 cC
Chapter 5 Properties 125

(A)
42

.
!i 8B

.
~~

:;;
.
~ 84
....
E
0
0
a: 80
:;;
'"
!;
28

'" UTS Unl"adlltad S3


• UTS I"adlatod S3
22
1.0 1.2 1.4 I.B
Draw Ratio

350
(8) o %EB Unlrradlal.d S3
• IIEB Irradiated S3

.!
~

:;; 300

......
Q,
E

E
0
0
a:
:;; 250
...
""
ci!
:;;
"
0 200
~~

~"

150
1.0 1.2 1.4 1.8
Draw Rallo

Figure 5. 7 Effect of draw ratio on tensile properties at room temperature of83


Chapter 5 Properties 126

65
(A)

60
..
!i
~ 55
'2
OD
~
OD 50
....
E
o
o
a: 45
Oi
'"5
40
o UTS Unl"adlatad P25
• UTS I... dllt.d P26
35
1.0 1.2 1.4 1.8 1.8
Draw Ratio

(6) o !lEB Unlrradlat,d P25


240 • !lEa I"adlated P26
OD
~
~

Oi
:;;
a.

....~ 200
E
0
0
a:
Oi
..oli. 180
"'"

.
Oi
s
i. 120
ill
;le

80
1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.7 1.8 1.9
Draw Ratio

Figure 5.8 Effect of draw ratio on tensile properties at room temperature ofP25
Chapter 5 Properties 127

(A)
7

8

CL

'"0'::5
c
o
~
;;;
",4
5

o UTS Unlrradlat.d SS
• UTS Irradlat.d SS
2

1.0 1.2 1.4 1.8


Draw Ratio (')

(8) o IIEB Unlrradlltad S3


• IIEB Irradiated SS
450

..
'&
c
o
~

c
.5!
;;;
If 250
o
iii
".

150

1.0 1.2 1.4 1.8


Draw Ratio (')

Figure 5.9 Effect of draw ratio on tensile properties at 100 'C of S3


(The explanation of draw ratio(*) will appear in Appendix Ill.)
Chapter 5 Properties 128

9
(A)


0..
27
0-
0"'"
co
~
.,.8
...'"
::>

o UTS Unlrradlat,d P26


• UTS Irradlatod P26
4

1.0 1.2 1.4 1.8 1.8


Draw Rallo (')

(B) o liES Unlrradlatod P25


• liES Irradiated P25

Cl 300
"'"
Cl
co
~
.,.
~
l!!
ID

200
~
i
..."
.!!
".

100

1.0 1.2 1.4 1.8 1.8


Draw Ratio (')

Figure 5.10 Effect of draw ratio on tensile properties at 100 cC of P25


(The explanation of draw ratio(*) is given in Appendix III.)
Chapter 5 Properties 129

largely controlled by physical networks, as the gel content of the samples was not high

enough to influence this property. At elevated temperatures the chemical networks

significantly affect the ultimate tensile strengths of the materials since some parts of the

physical network melts, and thus leaves the resistance to the applied tensile load to the

chemical network, which still remains at higher temperatures. The melting of these

crystallites will be discussed in section 6.2.1.

The effect of crosslinked structures on tensile strength is more pronounced

in the formulation containing 46.5 phr mop (S3) in comparison with material

containing less plasticiser (P25). This result is associated with the gel content that is

higher in S3.

Elongations at break of the biaxially drawn samples were found to fall with

increasing draw ratio. As mentioned in section 1.9, the presence of aligned polymer

chains in the plane of the film not only increases strength but also restricts further chain

extension, so that elongation at break is reduced. At room temperature the effect of

irradiation upon elongation at break was insignificant for all samples except undrawn

S3 (Figure 5.7B and 5.8B) for which the elongation at break was greatly decreased

upon irradiation .. This reduction is caused by the restriction of molecular chains due to

the presence of the crosslinked network. It seems that the higher mobility system is

more sensitive to changes in the internal structure, since the irradiation crosslinked

structures shows no effect on the elongation at break of undrawn P25.

The significantly increased elongations at break at 100°C for irradiated samples

of both compounds are highlighted in Figures 5.9B and 5.10B. At this temperature the

physical network formed by the crystallites is partially destroyed (see section 6.2.1);

consequently the polymer molecules in unirradiated specimens slip past one another,
Chapter 5 Properties 130

leading to failure at lower strains. The crosslinks in the irradiated samples prevent PVC

chains from completely slipping away from one another as a result in the higher

strength and elongation at break in crosslinked samples.

5.3.3. Impact Properties

The formulation containing 46.5phr mop was employed in the study of the
dependence of impact properties on draw ratio and crosslinked structures. An undrawn

sample and a series of drawn samples were prepared and exposed to electron beam
radiation at the dose of 6 Mrad. Impact testing was performed using a Rosand

instrumented falling weight impact tester; the experimental details are given in section

2.3.2.2.

The mode of fracture of all samples appears to follow the same ductile fracture

mechanism. Typical force-extension plots are displayed in Figure 5.11; (A) for

unirradiated undrawn 83; (B) for irradiated undrawn 83; (C) for unirradiated drawn 83
(D.R.=1.3) and (D) for irradiated drawn 83 (D.R.=1.3). The summary of the impact

study is shown in Table 1.5 and Figures 5.12-5.13. Considering first the unirradiated

series it can be seen that both maximum force and energy to peak force rise with the
increasing draw ratio. The alignment of PVC molecules in the plane of the film results
in an increased resistance to impact under falling weight impact test conditions(86).

The maximum impact forces measured for the irradiated series were higher

than those for the unirradiated series; as crosslinking takes place in the compound, the
chemical bonds in the network formed link adjacent PVC molecules, which results in a

greater resistance to specimen deformation under the applied impact load. The plot of

energy to peak force versus draw ratio also shows the improvement in impact
Chapter 5 Properties 131

H Foroe-Distanoe
299.9

~50.0

59.90

h,\ I
.f\.....l I
29.00 30.00
1"'IiI"

Figure 5.11 (A) A typical force-extension plot for un irradiated undrawn S3

H Foroe-Distance
~50.9

~90.e

59.eo

Figure 5.11 (B) A typicalforce-extension plot for irradiated undrawn S3


Chapter 5 Properties 132

H Force-Distance
a90.0

200.9

J.90.9

Figure 5.11 (q A typicalforce-extension plotfor uni"adiated drawn S3

H Force-Distance
390.0 i
i
I
....-T.
/ 1i
../.
,/ !
209.9 / i
,/ !
'
l
/ i::
/ i
l :
.../' 1
J.90 .9
/ i
/ i
/' ~
I '
.-' !
.l j
--,.--
o I --::::..---- -., , I
20.ge aO.ee
9 J.9.0e
I'M'"

Figure 5.11 (D) Atypical force.extension plot for i"adiated drawn S3


Chapter 5 Properties 133

1200

E 1100
E
~..
...
C
0
OD

1000
:E
~
0
l;
IL
900

...
E
"E
::I
800

Cl Unlrradiatcd 53
• Irradl.ted 53
700

1.0 1.1 1.3 I.S 1.8 1.7


Draw ratio

Figure 5.12 Effect of draw ratio on maximum force for S3

11

E
e
~..
D
10

...
OD
C

.!! 9
.c
....
.-
0
~
0
8
.......
IL

...
..,.,
.9

;;;
c
7

w 8

Q Vnirr.diatecl 53
• br_dl.led S3
S

1.0 1.1 1.2 1.4 1.8 1.7


Draw ratio

Figure 5.13 Effect of draw ratio on energy at maximum force for S3

J
Chapter 5 Properties 134

performance that is promoted by the presence of the crosslinked structures. The trend

is not as pronounced as the plot of maximum force versus draw ratio. This is the

consequence of the presence of plateau at the top of the force-extension plot (see

Figure 5.11), and hence the measurement of peak force is more precise than that of

energies to peak force.

5.4 EFFECT OF ANNEALING TEMPERATURE

Specimens of sample formulation S3 were biaxially drawn at 80°C at draw

ratios in the range I. 5 to I. 6 and· then were annealed under strain at 80°C, 90°C and

JOO°C for 20 minutes. The results obtained from percentage gel content and tensile

property measurements are discussed in the following sections.

5.4.1 Percentage Gel Content

The variation of percentage gel content with annealing temperature is

illustrated in Figure 5.15 and Table 1.6. The results show that the gel contents of

samples annealed at 90°C and 100°C were slightly lower than the sample which was

annealed at 80°C. It is known from studies into irradiation crosslinking of polyethylene

by many investigators(171-I7J) that the irradiation process preferentially induces the

formation of crosslinks in the amorphous phase. The degree of crystallinity of PVC

increases with increasing annealing temperature from above Tg up to 130°(62 ). These

observations lead to the possible explanation that at annealing temperatures higher

than 80°C the increase in crystallinity or the reduction of mobility of molecular chains

is responsible for the fall in the level of gel formation. The values obtained for gel

contents in samples annealed at 90°C and 100°C are very similar; it is suggested that

this is related to the near identical crystallinities determined in these two samples.
Chapter 5 Properties 135

5.4.2. Tensile Properties

. The plots of tensile strength and elongation at break versus annealing

temperature are displayed in Figures 5.15 to 5.16 and Table 1.7. The tensile properties
measured at room temperature are consistent with those reported by Gilbert et al,(86),

that is the annealing temperature appears to have little effect upon tensile performance.

Tensile properties at elevated temperatures, are however, increased by the presence of

crosslinking structures. The elongation at break at 100°C of the sample annealed at


80°C shows the greatest increase over the corresponding unirradiated sample under

the same test conditions. This is related to the fact that the highest gel content was
found in this sample, which leads to the greatest resistance to polymer flow at elevated

temperatures.

41

-
39 -

S7 -
1:
~
0
Cl
;;
-
'"
".
S5
.....---'
-
ss -
-
31
I
80 90 100
Annealing Temperature/DegC

Figure 5.14 Effect of annealing temperature on % gel content for oriented S3 at


draw ratio range of 1.5-1.6
Chapter 5 Properties 136

40

30 -
t----
--- T
~

..
0..
-
'"~
c
~ 20 - 0 UDlrr./UTS at lOODcaC
en • lu./UTS at IOODclC
.!! • Ualtr./UTS at Room Temp.

.
";;;
c
....
- lrt./UTS at Room Temp.

10 -
~

0
I
80 90 100
Annealing Temperature/DogC

Figure 5.15 Effect of annealing temperature on tensile strength for S3

400
0 Uaitr.f"BS at lOODcaC
• lrr./SBB at lOODc,C
•• Uairr.'''EB
lrt./_SB at
at Room Temp.
Room Temp.
-

....
~
ID
;;
300 -
-- "-
--
"
0
~
~
"~
-
c
B
w
~
200 - >--

100
I
,
80 90 100
Annealing Temperature/DegC

Figure 5.15 Effect of annealing temperature on elongation at break for S3


Chapter 5 Properties 137

5.5 CONCLUSIONS

Sample thickness was found to influence gel formation. The thinner the

specimen, the higher the gel content that can be produced; this results in the attainment

of the most desirable tensile properties. The macromolecular chain mobility in each

compound was found to affect gel formation; compound S3, containing 46.5 phr
mop, contained a greater gel content than formulation P25, with 25 phr mop.

Tensile and impact properties were observed to improve with the increasing
draw ratio. The crosslinked structures formed within the PVC compounds, which were

induced by electron beam irradiation, result in the improvement in mechanical


properties of the drawn samples. A significant improvement was found in tensile

properties when tensile tests were carried out at elevated temperatures.

The annealing temperature appeared to have only a small effect upon gel

formation and tensile properties of the formulation containing 46.5 phr DIOP. The

annealing temperature at 80°C was selected for this progranune as at this temperature
the highest gel content and draw ratio, as shown by the maximum elongation at break

in Figure 3.1, were achieved in this compound.


Chapter 6 Characterisation 138

CHAPTER 6

RESULTS AND DISCUSSION

IV CHARACTERISATION

6.1 INTRoDUCTION

The aim of this part of the programme was to investigate the changes in
structures after PPVC has been modified by stretching and/or irradiation crosslinking.

DSC and density measurements were carried out to ascertain crystallinity changes;
XRD was employed to examine crystallite orientation. Molecular orientation was

followed by birefiingence deterrninations. Thermal shrinkage and room temperature

recovery rate were also studied to investigate the stability of modified structures.

Structure-property correlations were drawn from the experimental data.

6.2 CRYSTALLINITY MEASUREMENTS

6.2.1 Differential Thermal Analysis

DSC traces of specimens cut from moulded sheets of two of the formulations
used in this study are shown in Figure 6. 1. The traces are very similar in appearance
and show three characteristic peaks. According to Juijn et al. (28) endotherm B

corresponds to the melting of relatively well developed crystalline structures known as


'primary crystallinity'. Gilbert and co-workers(11.18) have shown that endotherm A

arises because of the melting of secondary crystallites in PVC; 'secondary crystallinity'


is produced as a PVC network develops. It was also noted that the onset temperature
Chapter 6 Characterisation 139

~
~
:I:
E-<
0
~~

1 A
B

S3

P25

o 50 100 150 200 250


TEMPERATURErc
Figure 6.1 DSC thermograms for compounds S3 and P25
Chapter 6 Characterisation 140

of endotherm B coincides with the actual processing temperature employed during

sample preparation; in this work the moulding temperature of 175°C for 83 and P25

was used. Endotherm C relates to the melting of secondary crystallinity produced

during room temperature storage; as described by Juijn et al.(28). The D8C study in this

programme was primarily concerned with these three endotherms.

-Endotherm C

The effect of oriented structures on secondary crystallinity was investigated by

measuring the change in the enthalpy of endotherm C with sample age; samples of

formulation 83 in undrawn and drawn states, with draw ratios of 1.3 and 1. 6, were

used for this purpose. The results given in Figure 6.2 show that the enthalpy of

endotherm C of both undrawn and drawn samples fall on the same line. It may

therefore be concluded that orientation has no effect upon endotherm C. All of

measured enthalpies increase with time; at a high rate over the first three weeks,

followed by a slower rate of increase thereafter.

The effects of orientation and the formation of crosslinked structures upon the

enthalpy of endotherm C, for formulations 83 and P25 at the same age, were studied;

the findings are presented in Table 6.1. For a given formulation it can be seen that the

enthalpy of endotherm C is neither affected by sample drawing nor by electron beam

radiation treatment, and hence it may be concluded that neither orientation nor

irradiation has any effect upon secondary crystallinity. This observation was surprising

because it was expected that orientation and crosslinking would hinder molecular chain

movement, leading to a reduction in crystallinity formed during room temperature

armealing. It is possible that the draw ratios employed in the oriented samples are not

high enough to affect the formation of these crystallites. A similar argument can be
Chapter 6 Characterisation 141

C Ullorlcnted
• Oriented D.R.-!.3
• Oriented D.R.-U;

o 2 3 .58
Time/weeks
7 8
• 10

Figure 6.2 The variation ofthe change in enthalpy of endotherm C with time
for undrawn and drawn samples S3

made for the crosslinked samples: the gel content may not be great enough to prevent

the movement of molecular chains.

-Endothenns A and B

The effect of orientation and crossIinking upon endotherms A and B of sample


formulations 83 and P25 are presented in Table 6.2 and Figures 6.3-6.4. Considering

firstly the effect of orientation, it is noteworthy that the drawn samples shrink upon
heating; this movement of molecular chains might affect the measurement of the

melting endotherms, which are very broad due to the existence of a wide range of
Chapter 6 Characterisation 142

Table 6.1
The effect of orientation and cross linking upon enthalpy of endotherm C

SAMPLEID.R. ENTHALPY OF ENDOTHERM C (J/e)


UNIRR. SAMPLE IRR.SAMPLE

83 11.0 1.675 1.656


83/1.25 1.893 1.653
83 11.4 1.688 1.882
83 11.6 1.877 1.730

P25 I 1.0 2.298 2.464


P25/1.35 2.456 2.251
P25/1.6 2.287 2.267
P25/1.8 2.402 2.264

Table 6.2
The effect of orientation and crosslinking upon enthalpy of endotherm A and B

8AMPLE AB OF UNIRR. 8AMPLE (J/e) AB OF IRR. SAMPLE (J/e)


ID.R. ENDOmERM ENDOTHERM
A B A B

83/1.0 10.104 4.224 - 1.662


83/1.25 9.907 4.282 - 2.059
83/1.6 10.014 4.051 - 1.909

P25/1.0 8.500 5.083 4.817 1.878


P25/1.35 8.687 4.676 4.784 2.154
P25/1.8 8.548 4.800 4.353 1.981
Chapter 6 Characterisation 143

crystallite sizes and/or levels of perfection. As a result the accuracy of measurement of

the enthalpy is limited. The results in Table 6.2 show that the differences in

endotherms A and B between the undrawn and drawn sample for both formulations are

not significant. As mentioned in the beginning of this section, the B endotherm is

related to primary crystallinity and the A endotherm corresponds to secondary

crystallinity that is produced as a PVC network develops. The crystal1inities of the

oriented samples were expected to be higher than those of the undrawn samples,
according to the findings about polymer crystallisation induced by stretching(47-S7}. At

this stage, further interpretation of the effect of PPVC orientation on crystallinity is

probably not justified due to uncertainties in the measured enthalpy of the stretched

samples.

The effect of crosslinked structures on the thermogram is clearly seen in

Figures 6.3 and 6.4 for formulation S3 and P25, respectively; the full set of data is

presented in Table 6.2. It is can be seen that irradiation produces a lowering of the

enthalpy of endotherm A. This implies that the introduction of chemical networks by

irradiation partially destroys crystallinity although the crosslinking reaction mechanism

is not at present understood. The decrease of crystallinity was also found to reduce the

penetration resistance of the crosslinked samples with low gel contents, as discussed in

section 4.4.2.

The baseline in the thermogram is not distinct, and due to the close proximity

of peak A and B changes in the size of either one of these peaks will affect the

measurement of the other; it is thought that this is the reason for the reduction in the

enthalpy of peak B. In actuality the primary crystallinity is not changed by irradiation,

as shown later in the WAXD results.


Chapter 6 Characterisation 144

1 = Uni". unoriented
2 = I". unoriented
3 = Uni"" oriented 4
4 = I". oriented

50 100 150200 250


TEMPERATURE/oC
Figure 6.3 Effect o/i"adiation and orientation upon endothermA and B
for compound S3
Chapter 6 Characterisation 145

2
1 = Uni". unoriented
2 = I". unoriented 3
3 = Uni", oriented

" = I". oriented


4

5 100 150 200 250


TEMPERATURE/oC
Figure 6.4 Effect of i"adiation and orientation upon endotherm A and B
for compound P25
Chapter 6 Characterisation 146

6.2.2 Density Measurement

The densities of samples of formulation S3 were measured using a Davenport

density gradient column operated at 23.0±O.1 cC, as described in detail in section 2.3.6.

The results are displayed in Figure 6.5 and Table III (in Appendix 11). The density of
a sample that was unirradiated, drawn and annealed at 100°C is also included in the

graph to investigate the effect of annealing temperature upon density. Considering first

the unirradiated series, it is seen that density slightly increases with draw ratio. The
density of the sample annealed at 100°C was considerably higher than that of the

undrawn sample and the sample drawn and annealed at 80°C. The increase in density
was attributed to the rise in crystallinity in the sample annealed at the greater
temperature(18). It can be seen that orientation has a very small effect upon density in

comparison to the effect of the change in crystallinity by annealing, and hence it may

be concluded that biaxial orientation does not have a major influence upon the change

in crystallinity of PPVC. This deduction is consistent with the results from the study of
uniaxiaIly oriented PVC(63,79). It was suggested(79) that the change in density with draw

ratio is most likely related to conformation changes and ordering rather than true

crystallisation, since these changes are extremely small.

The effect of irradiation on density is much more pronounced than the effect of
orientation on density; this is highlighted in Figure 6.5. Apparently the densities of the

crosslinked samples are considerably higher than those of the uncrosslinked. The

observed increase was attributed to the fact that crosslinking causes additional
restrictions to the flexibility of the molecules, with a corresponding reduction in free

volume. This effect is widely known in vulcanised rubber systems. In the series of
crosslinked samples, the density was found to be independent of draw ratio. This
Chapter 6 Characterisation 147

shows that the influence of crosslinking on molecular arrangement is greater than that
of orientation,

1.250

.~

•S
Q
I!I
3t,240 -
eo
';

Q
I'l


0
CrolsliDkcd
UncrOlSliDkc4
Unlrr., Ta-lOODe,C
uso
I I I I
'" I I
1.0 1.1 1,2 1.S ". 1.5 U 1.7
Draw Ratio

Figure 6.5 Effect of irradiation and crosslinking upon density for compound S3

6.2 MEASUREMENT OF BIREFRINGENCE

The birefringence of the undrawn and drawn samples of formulation S3 were


carried out using optical microscopy, A quartz Ehringhaus compensator was used for

in-plane birefringence detenninations of all materials and the out of plane birefringence

measurements on the undrawn samples. To determine out of plane birefringence,

sections of different thicknesses were cut from the sample plaque; the birefringence of
each was recorded, The slope of a plot of birefringence against sample thickness

yielded the value for out of plane birefringence, The out of plane birefringence of

drawn samples was measured by conoscopy, This technique cannot be used for the
undrawn samples because the distance (d) between two isogyres (see section 2,3,5) is
Chapter 6 Characterisation 148

out of the measurable range. The positions of drawn samples used for determination of
birefringence are shown in Figure 6.6.

ABCDEFGHI J

1
2

3 C3 F3 H3
4
5 C5 E5 H5
6
7 D7 G7
8 F8
9
10

Figure 6.6 Schematic representation of the positions from which samples were cut
for birefringence determinations

Figure 6.7 shows the changes of plane orientation (the average value of the
two out of plane birefringence values) with draw ratio. It can be seen that all the plane
orientation values are extremely small (in the range 0.4xl0-4 to 3.2xl0-4) in
comparison to the values in the range 1xl0·3 to 5xl0·3 for uniaxially and biaxially
oriented UPVC<72.78.79.88); variations in plane orientation with draw ratio for the
samples used in this study do not show any clearly defined trends. Figure 6.8 compares
the birefringence values obtained herein with some published data(174) for oriented
UPVC materials.

Equation 6.1(79) shows that the total birefringence is a combination of the


birefringence arising from both crystalline and amorphous regions.
Chapter 6 Characterisation 149
4

, C3

• D7
B5
• 07
H3
C.
o H.

Cl!
·"
• .8
Uadnwa ..mple
o
1.0 t.f 1.2 1.3 1.4 1.5 1.8 t.7 1.8 1.t 2.0 2.1 2.2
Draw Ratio

Figure 6.7 Effect of draw ratio upon plane orientation for compound S3

15

UPVC dU'~

o
1.0 U U t.8 U 1.8 La t.7 1.t 1.t U ~ U
Draw Ratio

Figure 6.8 Comparisons of the measured birefringence of biaxially oriented PPVC


andUPVC
Chapter 6 Characterisation 150

..... 6.1

where M T, Mc, Ma and Mf are the total, crystalline, amorphous and form

birefringence, respectively; and Xc,v is the volume degree of crystallinity.

The crystalline orientation, measured by WAXD, was found to increase with

draw ratio (see section 6.4.1). Due to the very low crystallinity in PVC, birefringence

arises primarily from amorphous regions. The relaxation of the chains seems to be

extensive in the PPVC formulation containing 46.5 phr; the total size of the specimen

shrinks from 289cm2 to 242cm2 immediately after release from the BASE (see Figure

6.22). This probably is the reason for the very low birefringence. Residual stresses

remaining in the specimen from the compression moulding process may well affect the

final stress state after biaxial stretching. It can be concluded that molecular orientation

cannot be detected by this method.

6.4 CRYSTALLINE ORIENTATION

Crystalline orientation was examined by using two x-ray diffraction techniques:

firstly in the reflectance mode, to produce W AXD patterns and secondly in the

transmission mode to produce x-ray diffraction patterns on photographic plates. The

results are presented in the following sections.

6.4.1 Wide Angle X-ray Diffraction (WAXD)

Figure 6.9 and 6.10 illustrate WAXD traces of undrawn and drawn samples of

formulations S3 and P25, respectively. It can be clearly seen that every pattern

contains a peak at -17°28, with a second peak on its shoulder at -18.5°28, and a
Chapter 6 Characterisation 151

broad peak centred at -24.5°29. It is suggested that the peak at -28.7°29 belongs to a
component in the plasticiser, since this peak is smaller in the formulation with a lower
plasticiser content. The peak at 17°29, arising from x-ray reflections by the (200) plane
in the PVC crystallites, was used to follow crystalline orientation. Figure 6.11 shows
the orthorhombic unit cell of PVC, with the (200) plane highlighted; the polymer
chains lie parallel to the c-axis (known as the chain direction). This peak is referred to
as the A-peak, following the system used in the work of Gilbert et al. (86). The ratios of
the A-peak in the diffi'actograms of the drawn samples to the equivalent peak for
undrawn samples were calculated; the results are plotted against draw ratio in Figure
6.12. Considering firstly the oriented sample series, it can be seen that the A-peak ratio
increases with draw ratio. These findings show that biaxial stretching increases the
number of crysta1lites lying in the plane of the film. This results in a significant increase
in mechanical properties in the plane of the film.

Drawn. D.R.- 1.7


A

Drawn. n.R.- 1.25


A

Uadtawa sample

10 20 so 40
Degree Two Theta

Figure 6.9 WAXD traces of undrawn and drawn samples for compound S3
Chapter 6 Characterisation 152

Drawn. D.R.-l.8

DrawD.. D.R.-l.3

UlI.draw:D. samplo

to 20 30 40
Degree Two Theta

Figure 6.10 WAXD traces of un drawn and drawn samples for compound P25

(200jplane

s.IA

a ~
b

Figure 6.11 Orthorhombic unit cell of pvc showing the (200) plane
Chapter 6 Characterisation 153
1.8

1.5

1.4

..
.g
0:
...• 1.3

..<
u

1.2

III Unin:. 53
• Irr, 83
1.1
o Unirr. P15
• Irr. P25
o Unirr. S3/Ta-IOODeaC
4 In. S3/Ta-IOODcBC
1.0

1.00 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.80


Draw Ratio

Figure 6.12 The variation ofA-peak ratio with draw ratio

The A-peak ratio values are higher for the sample containing less plasticiser

(P2S); this is attributed to the higher stability of crystalline orientation. It appears that

crosslinking does not significantly affect crystalline orientation, since the A-peak ratio
of the irradiated samples followed the same trend as that of the unirradiated. S3

annealed at 100°C was found to give a slightly lower A-peak ratio compared with S3
annealed at 80°C at the same draw ratio. The observed decrease was caused by the

greater degree of relaxation of orientation that occurred in the sample that was

annealed at the higher temperature.

It is noteworthy that the increase in the A-peak ratio is probably not due to the
increase in crystallinity of the material. It was stated in the DSC study (in section

6.2.1) that biaxial orientation of PPVC has no effect upon either the enthalpy of
endotherm A or B. The increase in density because of orientation is very small, as
Chapter 6 Characterisation 154

discussed in section 6.2.2. In the study ofbiaxially drawn rigid PVC(174), the increase in
density with draw ratio was also found to very small. Hence it seems reasonable to

suggest that biaxial stretching does not affect crysta11inity.

6.4.2 X-Ray Diffraction Photograph

The directions through which x-ray transmission analyses were taken are

illustrated in Figure 6.13; the normal direction is defined when the x-ray beam is

perpendicular to the plane of the film.

Oriented pvc sheets

t
Ro'atl

Through thickness
;
Normal dircctiOll. ..L.~. _...._._. __._._._....._._. ___.............__...._.. H ••• H . . . . . . . ..

x-ray studies

Figure 6.13 'Normal direction' and 'through thickness direction' employedfor


transmission x-ray studies

The x-ray diffraction patterns of the PPVC films are displayed in the

photographic plates in Figures 6.14 and 6.15 for S3 and P25, respectively. The pattern

of the unstretched specimen S3 obtained in the normal direction, Figure 6. 14(a), shows
two circular halos corresponding to the lattice spacings d = 5.2A and d = 4.6A and a
Chapter 6 Characterisation 155

broader circular halo corresponding with d = 3.58A. The first two halos correspond to
the peaks at positions 17°29 and 18.5°29 in the reflectance mode diffiactograms
(figure 6.9); d = 3.58A appears as a broad peak centred at 24.5°29. The presence of
these rings shows that PVC is semicrystalline material. This is explained in the
following paragraph.

Crystalline materials contain a multitude of tiny crystallites with faces oriented


at all angles to the incident x-ray beam. Some of these crystallites are positioned such
that one set of parallel planes is at the correct angle (9) to reflect the incident x-rays.
There are many crystallites with this orientation and because the crystallites are small,
the spots on a photographic plate coalesce and appear as a ring to the naked eye. Since
crystal1ites have several sets of planes that are capable of reflecting, several diffiaction
rings are produced(17l). Crystalline polymers, when analysed in powder or unoriented
film forms, produce x-ray diffiaction patterns characterised by sharp rings. In the case
of PVC the rings are blurred and broad as a result of the low level of crystallinity
present; the presence of imperfect crystallites also adds to this effect.

Figure 6.14(b) presents the diffraction photograph in the normal direction of


the biaxially drawn sample S3. It can be seen that all the rings are sharper in
comparison to the undrawn sample (Figure 6.14(a». The reason for this is that the
crystallites become oriented in certain directions by the effect of biaxial stretching. In
these alignments, the number of sets of parallel planes that can produce reflections is
higher than in unoriented specimens, and hence sharper rings appear in the photograph.

It was mentioned in the WAXD discussions presented in section 6.3.1, that the
c-axis of the unit cell (see Figure 6.11) in biaxially drawn samples is aligned parallel to
the plane of the film; the a-axis and b-axis have mixed orientations. If the orientation of
Chapter 6 Characterisation 156

the c-axis is observed through the sample thickness (see Figure 6.13), uniaxial
orientation has occurred; x-ray transmission studies were carried out in this direction,

parallel to the plane of the film of biaxially stretched specimens, to see ifuniaxial
orientation had occurred preferentially ahead of biaxial orientation. The photographs

displayed in Figure 6.14(c) show the presence of rings instead of arcs in the diffraction

patterns. It was expected that arcs or spots would be seen in, especially in the two

inner rings, since these rings correspond to the (200) and (110) planes that lie parallel
to the c-axis. This axis was found to be oriented as a result of biaxial stretching. Since

(200) and (110) are oriented, they should produce reflections showing spots or arcs on

the photograph. This observation leads to the deduction that only a small quantity of
the crystallites are oriented; the draw ratio is not high enough to produce more

oriented structures and the high relaxation takes place after sample preparation. As the

photograph is not clear, it is difficult to detect any differences in intensities within the

ring. It is suggested that if an azimuthal scan was possible, the change in intensity may

be detected.

Similar results were found for samples P25 as shown in Figure 6.15(a),(b) and
(c). The diffraction photograph for the through sample thickness direction in Figure

6.l5(c) seems to show an arc, although the picture is not very clear. As expected,
crystalline orientation in the less plasticised formulation is more pronounced; this was

also found in the reflection mode work, where the A-peak ratio of P25 was more
sensitive to changes in draw ratio than S3 (see Figure 6.12).

6.5 SJUWlIKAGE MEASUREMENTS

The stability of macromolecular structures depends on the strength of inter-


molecular interactions and on the polymer chain conformations. Oriented polymers
(a) undrawn sample (b) drawn sample(D.R.=1.6), normal direction (c) sample (b), through thickness
direction

Figure 6.14 X-ray photograph for S3


(a) undrawn sample (b) drawn sample(D.R.=1.8), normal direction (c) sample (b), through thickness
direction

Figure 6.15 X-ray photograph/or P25


Chapter 6 Characterisation 159

may lead to a thermodynamically less stable arrangement. Extended chain elements

tend to decrease their end-to-end distances in such situations and to assume more
coiled conformations. The stability of orientation therefore depends on the changes in

internal energy that are determined by interactions between neighbouring elements of


the polymer chains. If the closer packing of oriented segments results in an energy

decrease that compensates for the drop in entropy, the molecular orientation will be

stable. Such a situation takes place if cohesive forces between polymer chains are
sufficiently strong; for example, in the regions of high crystallinity in semicrystalline

polymers. In amorphous regions the state of molecular orientation is not stable and
may be maintained only after cooling the system below Tg where molecular motion is

short-range and so slow that the orientation is practically "frozen-in". In conclusion the

chain-extended conformations are stabilised by the lowering of the energy of the


macromolecular system; if this energy is then somehow increased, extended

macromolecules tend to relax or shrink, reaching more stable coil formations(l44).

The glass transition temperatures of PPVC compounds S3 and P25 are lower

than room temperature, and hence the stability of oriented structures is expected to be
very low. It was found that the samples shrunk after drawing, cooling and removal

from the grips; the compound containing 46.5 phr mop (S3) reverted almost to its
original size. Subsequent annealing in the stretched state reduced this shrinkage, due to

the formation of ordered structures that held the oriented chains in position. It was

found that the sample with 25 phr mop (P25) did not shrink after annealing; sample
S3, however, still showed some shrinkage. The higher Tg ofP25 in comparison with

S3 implies that the molecular cohesion ofP25 is greater than that of S3. This leads to

the more stable oriented structures produced in P25.


Chapter 6 Characterisation 160

It was mentioned previously the physically cross1inked structures created


during the annealing period were not strong enough to halt the shrinkage process. The
introduction of chemically crosslinked networks was expected to modifY the shrinkage
behaviour of the oriented samples. The aim of this experiment, therefore, was to
investigate the effect of cross1inked structures on shrinkage properties.

6.5.1 Thermal Shrinkage

Thermal shrinkage measurements were determined using a Mettler Thermo-


mechanical Analyser as described in section 2.3.3.2.2. The study was focused on the
effect of draw ratio, %gel content and annealing temperature.

6.5.1.1 ElTect of Draw Ratio

Compound formulations S3 and P25 were investigated in this experiment. The


percentage area shrinkage (%AS) was calculated and plotted against temperature as
shown in Figure 6.16 and 6.17 for S3 and P25, respectively. To compare the behaviour
of different samples, temperatures corresponding to 5% AS and 50% AS, as displayed
in Figure 6.18 were read off the resulting trace; the data are displayed in Figures 6.19
and 6.20.

It can be seen that in both compounds %AS increases with temperature until a

maximum %AS was reached. This relaxation of orientation was attributed to the fact
that the motion of molecules in amorphous regions increases upon heating and that the
system tends to resume more highly coiled conformations, as mentioned earlier. The
draw ratio was found to have a very small effect on both the maximum %AS and %AS
temperature at 5% and 50%. In the irradiated series of S3, it can be seen clearly that
PERCENTAGE AREA SHRINKAGE 11

120

110

100

....... ao

-
,>4
~

'"
,.Q
en
80

... 70

80
<'"
...... 60
~

~ 40
0)
u
'"
0)
Po.
30
to Unhr., D.R.-l.24
20 [] Unin., D.R..-l.!4
o Vain., D.R..-l.70
10 • br., D.R.-l.23
• Iu., D.R..-1.48
0 • In., D.R..-1.66

·10

40 80 70 80 ao 100 110 120 130 140 160


30
Temperature/Dege

Figure 6.16 Percentage area shrinkage as a function oftemperature for S3


PERCENTAGE AREA SHRINKAGE 11

120

110

100

."
00
DO

-...
.>4
t:1
80
..cl

....
Cl)
70

<" 80

..".
00

t:1
SO

...""
40

"
Po SO
• Unirr., D,R.-l.38
20 0 Unirr., D.R.-l.64
0 Unirr .• D.R.-1.82
10 • Irr., D.R.-l.36
• Irr., D.R.-l.60
0 • In., D.R.-1.85
·10

30 40 80 70 80 10 100 110 120 130 140 160 180


Temperature/Dege

Figure 6.17 Percentage area shrinkage as a function of temperature for P25


Chapter 6 Characterisation 163

110

100
tQOX Recovery
90

eo
70
...
"
~ 60
"z
~
~o" Recovery
a: 50
l:

'" 40 I
...
~

a: I
.
~ 30

20
I
10 5" Recovery I
I
0
I'I)."
-,0
30 40 50 60 70 Ba 90 100 110 120 130 140 150
TEMPERATURE (OCl

Figure 6.18 Temperature at 5% AS (Ts.) and at 50% AS(Tso~J

100
Chapter 6 Characterisation 164
to

~-~

ID
:-~
Q UD.lrr., 5~AS
Cl Voin .• S09liAS
• Iu .• '''AS
• In., 50';AS

80

Figure 6.20 Effect of draw ratio upon temperature at 5 and 50 %AS for P25

crosslinked structures have the effect of reducing %AS, when compared with the
unirradiated (see Figure 6.16), most significantly at higher temperatures, resulting in a

decrease in the slope of the curve between 45°C to lOO°C. No difference can be

detected in the temperature range 30 to 45°C. The maximum %AS was reduced from
100% to 80% by the irradiation effect. %AS temperatures at 5% and 50% were found

to be increased in the irradiated series; the improvement of the temperature at 50% AS


was shown to be more pronounced. These results confirmed that irradiated crosslinked

structures can modify shrinkage properties distinctly at elevated temperatures.

Similar results were discovered in the study of P25; the effect of irradiation,
however, was less noticeable as shown in Figure 6.17. The maximum %AS was

reduced from 100% to somewhere in the range 90 to 95%. The different behaviours of
S3 and P25 can be seen in Figure 6.19 and 6.20; irradiated P25 shrunk to 50% at a

lower temperature than crosslinked S3. No effect on the temperature at 5% AS was


Chapter 6 Characterisation 165

detected. These phenomena are related to the lower gel content in P2S (see Table 5.1)
and the lower shrinkage.

6.5.1.2 Effect of Gel Content

The effect of gel content on %AS was examined using oriented samples S3

with a draw ratio of 1. 5. These samples were treated by electron beam radiation at
varying doses to produce different gel contents in the products. The plots of %AS

versus temperature of three samples with %gel contents of 26.2, 34.2 and 42.4 are
shown in Figure 6.21. As expected, the maximum %AS decreases with increasing gel

content. This shows that at higher temperatures the cohesive forces between adjacent

PVC chains are controlled by chemical networks; the greater the gel content, the more
stable are the oriented structures at elevated temperatures. The shrinkage behaviour at

low temperatures, from 25°C up to 50°C, was found to be independent of gel content.

This is consistent with the conclusion that at low temperatures the physical crosslinked
structures play an important role. Upon heating these physical networks start to melt

and the properties of the material will be controlled by the chemically crosslinked
network.

6.5.1.3 Annealing Temperature

The effect of annealing temperature on %AS ofunirradiated and irradiated S3

at draw ratio 1.5 is displayed in Figure 6.22. Apparently the shrinkage curve is shifted

significantly to the right when the annealing temperature is increased from 80°C to
IOO°C. Similar results were found previously by Gilbert and co-workers<86,. Two

distinct slopes of the plot can be seen between the onset shrinkage temperature and the
temperature at which the maximum %AS takes place. The gradient of the first part of
PERCENTAGE AREA SHRINKAGE 11

I.

80

.
V
CO
.l4
70

.Cl
.~

.Cl
80

...
Cl)
60
V

<
...
40
V
CO
Cl 30

...
V
to

Po. 20

10
~ Gel content
• 26.2
0 • 34.2
• 42.4

·10

20 30 40 60 80 70 10 I. 1.0 11. 12. I'. 14.


Temperature/Deg C

Figure 6.21 Percentage area shrinkage as afunction oftemperaturefor irradiated S3


PERCENTAGE AREA SHRINKAGE
t20

ttO

tOO

...."" 80

.
c:I
."
~
80

..."
Ul 70

80
«
.-
"
"
R
60

40
..
""
"
11<
30

20
• Unlrr., Ta-SO Dege
c Unin., Ta-PO DeSe
• Unirr., Ta-lOO Dele
to
• In., Ta-SO DaSe
• Jrr .• T.-90 Dale
0 • In., Ta-lOO Dele

·to

30 40 50 80 70 80 80 tOO 110 t20 t30 140 t50

Temperature/Dege

Figure 6.22 Percentage area shrinkage as a function oftemperature for S3


Chapter 6 Characterisation 168

the curve is smaller than that of the second; the second part starts approximately at the

annealing temperature. The smaller gradient arises as a result of improvements in the

structural order that serve to fix the oriented structure in position. The increased slope

in the second part is caused by the melting of the physically crosslinked structures
formed during the annealing period. Chemically crosslinked structures also shift the

shrinkage curve to the right and reduce the maximum %AS. The annealing

temperature is very effective in modifYing shrinkage behaviour. It can be concluded

that the physical network is an important complement to the irradiation crosslinked

network in PPVC. This effect is similar to that reported by Hjertberg and Dahl(\lS)who

used penetration to follow the effect of crosslinking on mechanical properties. They

found that the enlarged physical network created by annealing alone can improve

penetration resistance in the interval 60°C to 1IOoC and major penetration can be

avoided by the reinforcement conferred by the chemical network.

Annealing temperature shows no effect upon tensile properties, as discussed in

section 5.4.2. The increasing annealing temperature introduces one problem though;

the natural draw ratio of the sample is lower at temperatures above 80°C. If samples

are drawn to their maximum draw ratio at 80°C and then are annealed at a higher

temperature, failure will occur; the conditions for preparing samples need to be

optimised to maximise mechanical properties and minimise shrinkage.

6.5.2 Room Temperature Recovery Rate

Two sets of three samples of formulation S3 were drawn to the total area of

289cm2 in the stretcher head and were subsequently annealed at 80°C, 90°C and

IOO°C; their sizes were recorded with time. The plots of sample size against time are

displayed in Figures 6.23 and 6.24. Clearly the samples show a rapid initial recovery
Chapter 6 Characterisation 169

250
Total area ia the BASB - 289 cmA2 o Uairr.
• hr.
t:.. Uain.
• hr.
a Voirr.
• Itr.

Ta • 80 OlgC
220

o 2 a
Time/days

Figure 6.23 Total area of compound S3 vs time (in the first 2 days)

240
o Unitr .
• br.
tI. Unitt.
A [::, .. 1ft.
230
• B
C Unin .

• irt.
0
•'"e 220
...
~

~
h
C (; TI • 100 OegC

...<
~
0
2'0
Ta • 90 OlgO

200

Ta • 80 OlgC

'lop. A;B;C • 1;1.1:1.4


110

'0 '00 '000 10000


Time/days

Figure 6.24 Total area of compound S3 vs time


Chapter 6 Charaderisation 170

rate once released from the BASE. The sample size decreases exponentiaIIy with time.

The rate of recovery is fast in the first 1I 0 days and then becomes very slow there
after. The shrinkage was found to be reduced by increasing the annealing temperature,

as shown by the increase in gradient of the plot in Figure 6.24 with decreasing
annealing temperature. Structures produced with greater order at higher annealing

temperatures will be more highly stable, as discussed in the previous section. It seems

that irradiation shows has no effect on the recovery rate. This result confirms that
crosslinked structures only affect the modification of physical properties at elevated

temperatures.

6.6 SUMMARY OF THE RELATIONSHIP BETWEEN STRUCTURE AND PROPERTIES

The modified properties of PPVC after irradiation and orientation can be

explained by the influence of oriented and crossIinked structures.

6.6.1 Effect of Orientation

Orientation has a significant influence upon tensile and impact properties; both
of these were found to increase with draw ratio. This result is supported by the
evidence collected in the WAXD study: the rise in the A-peak ratio with draw ratio

indicates that the number of crystallites parallel to the plane of the film increases with

draw ratio. These structures lead to the improvement of the properties in the plane of
the biaxially stretched film.

It seems that the molecular orientation cannot be detected from the findings of
birefringence studies, since the measured values are extremely small and clear
relationships between birefiingence and draw ratio are not discernible. This implies
Chapter 6 Characterisation 171

that amorphous orientation cannot be maintained in biaxially stretched PPVC due to

the extensive relaxation in the amorphous regions.

Orientation was found to have no significant effect upon endotherm C,

measured by DSC, corresponding to the structural order produced during room

temperature storage. Biaxial orientation has no detectable effect on either endotherm

A or B. It is suggested that biaxial orientation in the range of draw ratios studied does

not affect the crystallinity of PPVC. This is supported by the density measurements, in

which the change of density with draw ratio was found to be extremely small.

It was shown that ultimate tensile strength and x-ray A-peak ratio increase with

draw ratio. The x-ray A-peak ratio is plotted against the UTS of undrawn and drawn

samples in Figure 6.25; there is a linear relationship between UTS and A-peak ratio in

both cases. It can be concluded that the crysta1lite orientation present in biaxially

drawn PPVC has a strong influence upon its mechanical properties. Even though the

crystallinity of commercially produced PVC is very low (-10%), it has been found to

significantly affect its processing, properties and applications as reviewed in reference

150.

Oriented PPVC suffers from shrinkage at higher temperatures and during

storage under ambient conditions, leading to the reduction of its mechanical properties;

this can be improved by annealing stretched PPVC at higher temperatures. The

physical crosslinks, however, are destroyed upon heating, and hence the introduction

of chemical crosslinks into the oriented structures to hold the chains in the oriented

positions was investigated.


Chapter 6 Characterisation 172

.0

50


~
~40

80

l!I UTS S3
• UTS P25
20

1.0 1.1 1.2 u 1.4 1.5 1.8 1.7


A-Peal: Ratio

Figure 6.25 Dependent of UTS on A-peak ratio for S3 and P25.

6.6.2 Effect of Irradiation Crosslinking

The development of crosslinked structures, signified by gel formation, was


found to increase tensile strength slightly and to reduce elongation significantly at

break at room temperature. A dramatic improvement in the tensile properties was


observed at elevated temperatures, when the physical network melts; linkages formed

in the crosslinking reaction holding the polymer chains together. The tensile properties
are controlled by the gel content in the compound, as shown in the plot between the

ultimate tensile strength and gel content for 46.5phr PPVC, irrespective of the
formulation, in Figure 6.26. Ultimate tensile strength rises slightly with gel contents in

the range 0% to 40%, after which point there is a sharp increase. This observation is
consistent with some results reported by Rodriguez(l25) in a study of chemical

crosslinking of PPVC with aminosilane.


Chapter 6 Characterisation 173

It appears that the crosslinked network produced is very loose since the

average molecular weights between crosslinks, shown in Tables 4.3, 4.6 and 4.9, are
high in relation to Mn.

1.40

1.20
...
CIII

~
.
:ll
U
G
1.00
0
'"
~

';j
rn 0.80
f-o
::>
I>l

0.80

0,40

o 10 20 30
~
40
Gel Content
50 '0 70 '0

Figure 6.26 Dependent of UTS on %gel content for S3.

The softening temperatures of the crosslinked compounds were found to be


higher than those ofthe uncrosslinked materials. The gel content has very little effect
upon the softening point, but the sample with the higher gel content gives the greatest
penetration resistance. In chemically crosslinked PPVC, the penetration resistance is
not only controlled by gel content but also by the physical crosslinks. The study of the
physical network complementing the chemical one is shown in reference<1lS>.

The differences in the tensile properties between irradiated and unirradiated


oriented PPVC at the same draw ratio are more distinct at 100°C than at room
temperature. Crosslinking was found to have no effect on crystalline orientation, since
Chapter 6 Characterisation 174

the variation of x-ray A-peak ratio with draw ratio was the same for both irradiated

and unirradiated samples. Irradiated stretched PPVC therefore maintains the property

improvements gained from the effect of molecular orientation at increasing draw


ratios.

Secondary crystallinity, measured by DSC, was found to be partially destroyed

by irradiation. The chemical bonds created during irradiation link polymer chains

together; mechanical properties are maintained at room temperature, whilst at elevated

temperatures they are improved. These covalent bonds cause additional restriction to
the flexibility of the molecules, with a responding reduction in free volume. This

explains the increase in density of irradiated samples in comparison to unirradiated

compound.

Crosslinking was found to reduce the shrinkage of oriented samples especially


at elevated temperatures; no effect was apparent on the onset of shrinkage temperature

(the chemical networks were expected to increase the onset temperature that would
have lead to an increase in the service temperature of the PPVC products); upon

heating above this temperature, crosslinked samples shrunk to a lesser extent than the
uncrosslinked ones. The crosslinked structures reduce the maximum %AS; this effect
becomes more pronounced with increasing gel content. No significant effect of

irradiation crosslinking can be seen upon room temperature recovery rate. It is possible

that the amount of chemical crosslinks is not high enough to prevent the relaxation of
polymer chains that occurs at increased temperatures and during storage at room

temperature (the gel contents of irradiated stretched samples are in the range of 30%
to 38%). Another possible reason is that the crosslinked structure produced is loose,

and hence the number of linkages is not high enough to hold the molecular chains in

the oriented state. It may be possible to avoid shrinkage by choosing a system with a
Chapter 6 Characterisation 175

very high gel content. This value should be higher than 50%, as can be seen from
Figure 6.26, where a gel content greater than 50% produces dramatically modified

properties. The annealing temperature is more effective in modifying shrinkage

behaviour: an increase in this value can significantly delay the maximum and onset of

shrinkage.

6.6.3 Conclusions

The properties of crosslinked oriented PPVC are modified by the effect of

molecular orientation and by chemical linkages between polymer chains. The

improvement of tensile properties and shrinkage are more significant at elevated


temperatures. The dimensional stability of drawn PPVC can be modified by an increase

in annealing temperature.

Finally, a schematic diagram summarising the effect of stretching and

irradiation crosslinking upon PPVC is presented in Figure 6.27.


Chapter 6 Characterisation 176

PI.utirln,

Original sheet

Bia:dally stretched sheet

+H--=~ Mo,. "'1,taWIfI 11_


In IM planuftMfllm

1 Irradiation ,<=linking

IlTadiation crosslinked
biaually oriented sheet

Figure 6.27 Schematic representation o/irradiation cross/inked, biaxially


stretched, plasticised PVC
Chapter 7 Conclusions 177

CHAPTER 7

GENERAL CONCLUSIONS AND SUGGESTIONS FOR FuRTHER STUDY

7.1 GENERAL CONCLUSIONS

Stretched and unstretched PPVC formulations containing TMPTMA as a

radiation sensitiser, are readily crosslinked upon exposure to electron beam radiation;
this is shown by the appearance of gel in the irradiated samples.

The liquid tin stabiliser Stanclere TL was found to be the most suitable
stabiliser for PVC in the study of crosslinking of oriented PPVC compounds. The

amount of gel formed was found to increase with irradiation dose and TMPTMA level,

but was found to decrease with increasing concentration of organotin stabiliser. The

optimum concentrations of TMPTMA and stabiliser were ten and three parts per
hundred, respectively. An irradiation dose of six Mrad was found to provide

satisfactory crosslinking conditions.

The irradiation process gives rise to significant changes in the physical


properties of PPVC compounds. Improvements in tensile properties are more

pronounced at elevated temperatures than at room temperature. These are controlled

by the gel content in the compound. The crosslinked structures also improve the

penetration resistance at higher temperatures.

Sample thickness influences the extent of gel formation: the thinner the

specimen, the higher the gel content that is produced upon irradiation. This results in

the attainment of the most desirable tensile properties. The macromolecular chain
Chapter 7 Conclusions 178

mobility in each compound was found to affect gel formation; compound S3, with a
mop content of 46.5 pbr, contained a greater percentage gel than formulation P25,

with 25 pbr mop.

Tensile and impact properties were found to improve with increasing draw

ratio. The crosslinked structures formed within the PVC compounds, which were
created by electron beam irradiation, result in the improvement of the mechanical

properties of the drawn samples. A significant improvement was found in tensile

properties when testing was carried out at elevated temperatures.

The annealing temperature seems to have only a small effect upon gel

formation and tensile properties of the formulation containing 46.5 phr DIOP.

From the DSC study, both orientation and crosslinking were found to have no

significant effects upon endotherm C, corresponding to the structure order produced

during room temperature storage. Biaxial orientation shows no detectable effect on


either endotherm A or B. In contrast, a reduction of crystallinity was discovered in

irradiated samples, which is signified by the lowering of the enthalpy of endotherms A

andB.

The effect of orientation upon density seems to be very small, whilst

crosslinking significantly increases the density.

It seems the molecular orientation can not be detected by the measurement of

birefiingence, since the measured values are extremely small and clear relationships

between birefringence and draw ratio are not discernible.


Chapter 7 Conclusions 179

The results from WAXD studies produce strong evidence that the properties of
the PVC films are improved by crystallite orientation. This is attributed to the fact that

the number of crystallites parallel to the plane of the film increases with draw ratio, as

shown by the rise in the A-peak ratio with draw ratio. Crosslinking was found to have

no effect on the aligmnent of crystallites.

Finally, crosslinking reduced the shrinkage of oriented samples, especially at

elevated temperatures; no effect was apparent on the onset of shrinkage temperature.


Upon heating above the onset temperature, the shrinkage of crosslinked samples was

reduced compared to the uncrosslinked ones. The crosslinked structures reduce the
maximum %AS; this effect becomes more pronounced with increasing gel content. No

significant effect of irradiation crosslinking can be seen upon room temperature

recovery rate. Annealing temperature was discovered to strongly influence shrinkage

both at higher temperatures and at room temperature.

7_2 SUGGESTIONS FOR FuRTHER STUDY

Residual unreacted double bonds from TMPTMA were found in the

crosslinked product; these are known to promote oxidative degradation in polymer,


which can lead to undesirable properties. The degradation reactions and their effects

upon the properties of irradiated samples after ageing at room temperature should be

studied. Functional groups produced by the degradation reactions, e.g. carbonyl


groups may be detected by infra-red spectroscopy. The study of the change in tensile

properties over time would reveal the effect of unsaturation upon the long term

properties of the irradiated products.


Chapter 7 Conclusions 180

It was found that the increase of A-peak ratio with draw ratio in the WAXD
study can be clearly ascribed to crystallite orientation. Additional x-ray work would

complete this study; the use of pole figure analysis is suggested. With this technique, it

would be possible to depict the distribution of the coaxes.

The gel content, and hence the mechanical properties, can be improved by

increasing the irradiation dose, however the level of degradation also increases.

Crosslinking via a chemical reaction route may be an alternative approach, as it would

be possible to produce very high gel contents in the crosslinked product by varying the

concentration of the components and the conditions.


References 181
REFERENCES

1. W.S. Penn, "PVC Technology", 3rd edn. ,Appl. Sci. Pub., London, 1971.
2. H.A. Sarvetnick, "Polyvinyl Chloride", Van Nostrand Reinhold Company, New
york, 1969.
3. T. Hjertberg and E.M. Sorvik, J. Appl. Polym. Sci., n, 2415(1978).
4. J. Malac, J. Appl. Polym. Sci., 11,1767(1969).
5. S. Orrnondroyd, Br. Polym. J., 2Q, 353(1988).
6. M.W. Allsopp, Chapter 7 in "Manufacture and Processing of PVC",
R.M. Burgess (ed.), Appl. Sci. Pub., London, 1982.
7. J. Hattori, K. Tanaka and M. Matsuo, Polym. Eng. Sci., ll., 199(1972).
8. G.F. Neilson and S.A. Jabarin, J. Appl. Phys., 46(3), 1175(1975).
9. W. Wenig, J. Polym. Sei. : Polym. Phys. Ed., 16, 1635(1978).
10. D.G. Faulkner, J. Maeromol Sci.-Phys., Bll, 251(1975).
1l. M.Gilbert, D.A. Hamsley and A. Miadonyl, Plast. and Rubb. Proc. and Appli.,
1,343(1983).
12. M.W. Allsopp, Chapter 8 in "Manufacture and Processing of PVC",
R.M. Burgess (ed.), Appl. Sci. Pub., London, 1982.
13. P. Benjarnin, Proc. RPI Int. Conf. PVC Processing, Egham Hill, England,1978.
14. A. Gonze, Plastiea, 24,49(1971).
15. M. Lamberty, Plast. Mod. Elast., 2Q, 82(1974).
16. S.V. Pate! and M. Gilbert, Plast. and Rubb. Proc. and Appli., ~, 85(1985).
17. J.W. Summer, E.B. Rabinovitch and J.G. Quisenberry, J. Vinyl Teehnol., L
32(1985).
18. M. Gilbert and J.C. Vyvoda, Polymer, n, 1134(1981).
19. N.A. Isles and O. Delatychi, "Polymer 85", Characterisation and analysis of
Polymer(IUPAC). Australian Acadamy of Science Pub. Royal Australian
Institute, 102(1985).
20. J.A. Juijn, J.H. Gisoft and W.A. de Jong, Kolloid-Z.u.Z. Polymere, 235,
1157(1969).
References 182
21. O.P. Obande and M. Gilbert,J. Appl. Polym. Sci., 'JL 1713(1989).
22. G. Natta and P. Corradini, J. Polym. Sci., 20, 261(1956).
23. C.E. Wilkes, V.L. Folt and S. Krimm,Mecromolecules, 2(2), 235(1973).
24. V. Nardi, Nature, 191,563(1961).
25. M. Marrni and V. Nardi, Nature, 199, 247(1963).
26. v.P. Lebedev, N.A. Okladnov, KS. Minsker and B.P. Shtarkman, Polym. Sci.
USSR,1,724(1965).
27. v.P. Lebedev, N.A. Okladnov and M.N. Shlykova, Polym. Sci. USSR,2,
553(1967).
28. lA Iuijn, lH. Gisoft and W.A. de long, Kolloid-Z.u.Z. Polymere, 251.
456(1973).
29. RW. Smith and C.E. Wilkes, J. Polym. Sci., Part B, 2., 433(1967).
30. A Nakajima and S. Hayashi, Kolloid-Z.u.Z. Polymere, 229, 12(1969).
31. RI. Hobson and AH. Windle,Makromol. Chem. TheorySimul., Z, 257(1993).
32. RI. Hobson and AH. Windle, Polymer, 34(17), 3582(1993).
33. P.H. Burleigh, J. Amer. Chem. Soc., g 749(1960).
34. D.M. White, J. Amer. Chem. Soc., g 5678(1960).
35. v.w. Titow, "PVC Technology", 4th edn., 450,1984, EIsevier, London.
36. M. Gray and M. Gilbert, Polymer, 11. 44(1976).
37. P.C. Dawson, M. Gilbert and W.F. Maddams, J. Polym. Sci., Part B, 29,
1407(1991).
38. RI. D'Amato and S.Strella, Appl. Polym. Symp., ~ 275(1969).
39. B.P. Shtarkman, V.P, Lebedev, T.L. Yatsynina, B.P. Kosmynin, V.I.
Gerasimoo, Ya.v. Genin and D.Ya. Tsvankin, Polym. Sci. USSR, l4,
1826(1972).
40. KG. Patterson, S.T. Padgett and N.A. Peppas, Colloid Polym. Sci., 260,
851(1982).
41. DJ. Blundell, Polymer, 20, 934(1979).
42. A Dorrestijin, AE.M. Keijzers and K te Nijenhuis, Polymer, ~305(1981).
43. lW. Summers, J. Vinyl Technol., 1, 107(1981).
References 183
44. J.w. Summers, E.B. Rabinovitch and P.C. Booth, Jvinyl Technol.,~ 2(1986}.
45. H.R. Brown, M. Kasakevitch and G.D. Wignall, Polymer, 27, 1345(1986}.
46. D.G.H. Ballard, AN. Burgess, lM. Dekoninok and E.A. Robert?po{vm~8~
(1987).
47. J.R. Katz, Nature, 1, 169(1925}.
48. J.R. Katz, Trans. Faraday Soc., 32, 77(1936}.
49. P.l Flory, J. Chem. Phys., U, 397(1947}.
50. D. Luch and G.S.Y. Yeh,J. Polym. Sci., 11467(1973}.
51. AN. Gent,J. Polym. Sci., A3,3787(1965}.
52. IT. Judge and R.S. Stein, J. Appl. Phys., 32, 2357(1962).
53. A Keller and M.l Machin, J. Macromol. Sci.(phys.), B1, 41(1967}.
54. G.S.Y. Yeh and L. Lambert, J. Appl. Phys., 42, 4614(1971).
55. G.S.Y. Yeh and P.H. Geil,J. Macromol. Sci.(phys.), B1, 251(1967).
56. G.S.Y. Yeh, Polym. Eng. Sci., 1§, 138(1976).
57. G.S.Y. Yeh, Polym. Eng. Sci., 16, 145(1976).
58. T.E. Brady, Polym. Eng. Sci., 16, 638(1976).
59. A.J. de Vries and C. Bonnebat, Polym. Eng. Sci.,l§, 93(1976}.
60. lC. Vyvoda, M. Gilbert and D.A. Hemsley, Polymer, 2l, 109(1980}.
61. C. Baker, W.F. Maddarns and J.E. Preedy, J. Polym. Sei., U, 1041(1977}.
62. S. Ohta, T. Kajiyama and M. Takayangi, Polym. Eng. Sci., 16,465(1976).
63. Z.Liu and M. Gilbert, Polymer, 28, 1303(1987}.
64. M. Gilbert and Z. Liu,Plast. Rubb. Proc. Appl., 2., 107(1988)
65. H. Illers, Die Macromol. Chemie, 127,1(1969}.
66. S. Hibi, M.Maeda and H. Kubota, Polymer, ll, 801(1977}.
67. M. Theodurou and B. Jasse,J. Polym. Sci., 24, 2643(1986}.
68. T.E. Bradyand S.A. Jabarin, Polym. Eng. Sci., 17. 686(1977).
69. M. Kashiwagi and I.M. Ward,Polymer, ll, 145(1972).
70. H. Springer, R. Neuert, F.D. Muiller and G. Hinrichsen, Colloid Polym. Sci.,
261, 800(1983}.
71. T.G. Meijering, P. Benjamin and K. Eygelaar, Gas, 2, 1(1986}.
References 184
72. M.E.R. Robinson, DJ. Bower and B.P. Maddams, J. Polym. Sci, Polym. Phys.
Ed., .IQ, 2115(1978).
73. J.G. Rider and E. Hargreaves, J. Phys. D, J., 993(1970).
74. S. Shindo, B.E. Read and RS. Stein, Makromol. Chem., 118, 272(1968).
75. J.L. White and I.E. SpruieII, Polym. Eng. Sci., 23, 247(1983).
76. DJ. Bower, I. King and W.F. Maddams, J. Macromol. Sci., B20, 305(1981).
77. J. King and DJ. Bower, J. Appl. Polym. Sci., J.2., 787(1988).
78. J.G. Rider and E. Hargreaves, J. Phys., J., 993(1970).
79. S.A. Jabarin,Polym. Eng. Sei., ll, 638(1991).
80. M.A. Kotnis and J. E. SpruieII, Polym. Eng. Sci., 29,1528(1989)
81. C. Baker, W.F. Maddams and lE. Preedy, J. Polym. Sci., 12,1041(1977).
82. E.V. GouinIock, J. Polym. Sci., Polym. Phys. Ed., ll, 961(1975).
83. PJ. Lematra, A KeIIer and M. Cudby,J. Polym. Sci., Polym. Phys. Ed., 16,
1507(1978).
84. M.Gilbert and lC. Vyvoda, Polymer, .l.2, 862(1978).
85. L.S. Rayner and P.A. Small, Br. Pat., 847676.
86. M. Gilbert, D.l Hitt and MJ.B. Harte, Proc. Inst. ofMaterial. ConferencePVC
93, Brighton, April, 1993, p. 368.
87. I. Umemura, T. Takenaka, S. Hayashi and R Gotoh, Bull. Inst. Chem. Res.
Kyoto Univ., 46, 228(1968).
88. J.G. Rider and E. Hargreaves, J. Polym. Sci., part A2, L 829(1969).
89. M.E.R. Robinson, DJ. bower and W.F. Maddams,Polymer,.l.2, 773(1978).
90. W.F. Maddams, J. Macromol. Sci.-Phys., BI4(1), 87(1977).
91. D.L. Smith, S.H. Hookanson and J.L. Irvine, J. Vinyl Technol.,~, 7(1986).
92. AI. Chapiro, Chim. Phys., 895(1956).
93. P. Alexander, A Charlesby and M. Ross, Proc. Roy. Soc. Land, 223A,
392(1954).
94. AA. MiIIer, Industrial and Engineering Chemistry, 21, (1959).
95. W.A. Salmon and L.D. Loan, J. Appl. Polym. Sci.,.IQ, 671(1972).
96. S.H. Pinner, Nature, 183, 1108(1959).
References 185
97. T.J. Szymcak and J.A Manson, Modern Plastic, August, (1974).
98. J. Dobo, Pure & Appl. Chem., 46, 1(1976).
99. T.N. Bowrner, M.Y. Hellman, G.N. Taylor and w.I. Vroom,Org. Coal Appl.
Polym. Sci. Proc., 48, 496(1983).
100. M. Izumi, F. Suzuki and T. Yuri, Sumitomo Denki (Sumitomo Electric Rev.),
October, 44(1965).
101. Z. Hell, M. Ravlic, Lj. Borgdanovic, J. Males, I. Dvomik, F. Ranogajec,
M. Ranogajec and Tudoric-Ghemo, 1. Radiat. Phys. Chem.,22, 619(1985).
102. A Zyball, Kunstoffe, 72, 487(1982).
103. Z. Hell, Z. Junakovic, F. Ranogajec, I. Dvornik and M. Baric,Makromol. Chem.,
Maeromol. Symp., 29, 267(1989)
104. K. Kojima, H. Kumafuji and K. Veno, Radial. Phys. Chem., 18,859(1981).
105. E. Scalco and W.F. Moore, Radial. Phys. Chem., 21, 389(1983).
106. G. de Hollain, Radial. Phys. Chem., 15, 595(1980),
107. T.N. Bowrner, 0.0. Davis, T.K. Kwei and w.I. Vroom,1. Appl. Polym.Sci., z.2,
3669(1981).
108. T.N. Bowrner, M.Y. Hellman and w.I. Vroom, 1. Appl Polym. Sci., ~
2083(1983).
109. T.N. Bowrner, W.I. Vroom and M.Y. Hellman , J. Appl. Polym. Sei., ~
2553(1983).
110. AH. Zahran and F.M. Ezz Eldin, Radial. Phys. Chem., 2l, 175(1986).
111. AH. Zahran, E.E. Nofal, M.Z. Elsabee and M. A EI-Sabee, J. Appl. Polym.Sci.,
24, 1723(1979).
112. L.P. Nethsinghe and M. Gilbert, Polymer, ~1935(1988).
113. L.P. Nethsinghe and M Gilbert, Polymer, 30,35(1989).
114. T. Hjertberg, R. Dahl and E. Sorvik, J. Appl. Polym. Sei., TI,1239(1989).
115. T. Hjertberg and R. Dahl,1. Appl. Polym. Sei., 42,107(1991).
116. K. Mori and Y. Nakamura, J. Polym. Sei. A-I, 2, 639(1971).
117. K. Mori and Y. Nakamura,J. Polym. Sei. Polym. Chem. Ed.,.l§. 1981(1978).
118. M. Gonnu and M. Michel, Makromol. Chem. Maeromol. Symp., ~ 219( 1989).
References 186
119. O. Rodriguez-Fernandez and M. Sanchez-Adame,.l. Vinyl. Technol., ll.
184(1991).
120. J.T. Lewis, D. Collins and C. Malani, Brit. Pat. 139248, 1969.
121. J.C. Saam and B. Thomas, Brit. Pat. 1485263, 1973.
122. MS. Heam, J.D. Baird, L.P. Nethsinghe and M. Gilbert, Polym. Comm., ll.
193(1990).
123. 1. Kelnar and M Schatz,.l. Appl. Polym. Sci., ~ 657{l993).
124. 1. Kelnar and M. Schatz,.l. Appl. Polym. Sci., ~ 669{l993).
125. O. Rodriguez-Fernandez, Ph.D. Thesis, IPTME, Loughborough university,
Loughborough, U.K., 1994.
126. E.W. Bennett, Radiat. Phys. Chem., M. 947(1977).
127. H.E. Quinn, Radiat. Phys. Chem., 14,953(1979).
128. 1.Uda, S. Tada, Y. Takeda, S.Suzuki, K. Kozima, K.Ueno and S. Torisu,
Radiat. Phys. Chem., 22. 855(1985).
129. L.D. Loan, Radiat. Phys. Chem., 2. 253(1977).
130. U. Hochstrasser, Wire Industry, Jan., 46(1985).
131. D.C. Alexander,PlasticsandPo/ymer, Oct, 195(1975).
132. R.A Bellino, Wire Journal, Oct, 75(1975).
133. AF. Matheson, Reprintfrom Electrica (Times), 5 June 1981.
134. Hy-vin Crosslinkable PVC Compound for Extrusion, Technical Information
leaflet, Norsk Hydro Polymers Ltd., 1984.
135. M. Gilbert; DJ. Hitt and MJ.B. Harte, accepted for publication by Rubber
Composite Processing and Application, April 1994.
136. M. Gilbert and DJ. Hitt, Private communication, "A Confidential Report on the
Orientation of PVC Compounds", Loughborough University, Loughborough.
137. D.J. Hitt and M Gilbert, Material Sci. Technol., 8, 739(1992).
138. DJ. Hitt, Private communication, "Orientation of PVC Compounds", Dec. 1993,
Loughborough University, Loughborough.
139. DJ. Hitt, Private communication, "Orientation of PVC Compounds", April,
1990, Loughborough University, Loughborough.

u )
References 187
140. DJ. Hitt and M. Gilbert, Polymer Testing, n, 219(1994).
141. AR Berens,Polym. Eng. Sci.,l4, 318(1974).
142. K. Mori and Y. Nakamura, J. Appl. Polym. Sci., 22, 2685(1978).
143. P.D. Ritchie, "Plasticisers, Stabilisers and Fillers", ButterwortheCo(Publishers)

Ltd, London, 1972


144. M. Trznadel and M. Kryszewski, J.MS.-Rev Macromol. Chem. Phys.,
C32(3&4),259(1992).
145. P.1. Flory and J. Rehner, J. Chem. Phys., lL 521(1943).
146. A Eringhaus, Z. Kristallogr., (A) 102, 85(1939).
147. J.W. Gifford, Proc. Roy. Soc., (A) Mo 193(1910).
148. N.H. Hartshorne and A Stuart, " Crystal and the Polarising Microscope",
Edward Arnold & Co., London.
149. AF. Hallimond, "The Polarising Microscope", 3 edn., Vickers Ltd., England,
1970.
150. M. Gilbert, Progress in Rubber and Plastics Technol.,.2., 143(1993).
151. 1. Wypych, "Polyvinyl Chloride Degradation", Elsevier, New York, 1985.
152. J. Wypych, J. Appl. Polym. Sci., 20(2), 557(1976).
153. E.L. White, "Encyclopedia of PVC", Chapter 13, Vol. 2, edited by L.I. Nass,
Merce1 Dekker Inc., Newyork, 1977.
154. AH. Frye, RW. Horst and M. A Poliobagis, J. Polym. Sci., A2, 1765,1785,
1801(1964).
155. P.P. Klemchuk, Prog. Chem., 85, 1(1968).
156. H. Lagner, G. Zeppenfeld and A. Barti, Plast. Kautschuk, J1, 76(1966).
157. F. Mori, M. Koyama and Y. Oki, Angew. Makromol. Chem., 75, 123(1979).
158. R Gachter and H. Muller, " Plastics Additives Handbook", 4th edn., Hanser
Publishers, Munich, 1993.
159. P. Baker and RF. Grossman, "Handbook of PVC Formulation", Chapter 8,
Edited by E.1. Wickson, John WiJey & Sons, Inc, New York, 1993.
160. W. Jasching, Kunststoffe, i2, 458(1962).
161. B.w. Rockett, M. Hadlington and w.R. Royner, Polym. Lett., 2,371(1971).
References 188
162. F. AJari-Moghadam, G. Ayrey and RC. Poller, Eur. Polym. J., 11, 649(1975).
163. G. Ayrey, RC. Poller and lH. Siddiqui, J. Polym. Sci., Part A-I, 10(3),
725(1972).
164. G. Ayrey, RC. Poller and lH. Siddiqui, Polymer, 11, 299(1972).
165. G. Ayrey, RC. Poller and lH. Siddiqui, J. Polym. Sci., Part B, ~ 1(1970).
166. T. Suzuki,l Takakura and M. Yoda, Eur. Pofym. J., 1,1105(1971).
167. lH. Siddiqui, PhD. Thesis, University of London, 1970.
168. R.C. Becker, J.H. bly, M.R. Cleland and J.P. Farrell, Radiat. Phys. Chem., 14,
353(1979).
169. W.L. McLaughlin, A.W. Boyd, K.H. Chadwick, J.C. McDonald and A. Miller,
"Dosimetry for Radiation Processing", Chapter 2, Taylor & Francis, London,
1989.
170. M. Nikolova and M. Mateev, J. Appl. Polym. Sci., 1I. 201(1991).
171. G.S.Y. Yeh, C.J. Chen and D.C. Boose, Colloid Polym. Sci., 263, 169(1985).
172. C.J. Chen, D.C. Boose and G.S.Y. Yeh, Colloid Polym. Sci., 269, 469(1991).
173. C.J. ChenandG.S.Y. Yeh, ColloidPolym. Sci., 269, 353(1991).
174. Z. Liu and M. Gilbert, Current Trends in PVC Technology Symposium,
Louhgborough University, Louhgborough, u.K., September 1994.
175. M.L. Miller," The Structure of Polymer", Reinhold Publishing Corporation, New
York, 1966.
Appendix 189
APPENDIX I

TableLl
Effect of sample thickness upon percentage gel content for S3 and P25.

S3 P25

SAMPLE %GEL SAMPLE %GEL


THICKNESS/mm CONTENT" THICKNESS/mm CONTENT"

0.14 50.9 0.22 30.1


0.21 44.1 0.35 24.9
0.24 39.7 0.49 18.1
0.28 36.5
0.31 29.9
0.35 26.1
*Percentage gel content values presented in this programme are the average of
at least two measurements;
n
_ 'L,n,x,
Arithmetic means (x) were calculated: x=.r=..L-
N

1:(X -x)'
;-1 '
Sample standard deviations (cr) were calculated: (J"= ' , - " ' ' ' - - - -
N-l

where ni is the number of results of magnitude xi and N is the total number of results.

e.g. for formulation S3:

D.R. %gel content (3 measurements) Average cr


1.26-1.28 36.82/37.99/37.73 37.38 0.59
1.40-1.44 36.12/37.56/37.11 36.93 0.74
Appendix 190

TableL2
Effect of sample thickness upon tensile properties# at 100 cCfor S3 and P25

S3 P25
SAMPLE UTS/MPa %EB SAMPLE UTS/MPa %EB
mICKNESSfmm mICKNESSfmm
0.22 6.07(.02) 354(8) 0.22 5.46(.18) 318(11)
0.31 5.25(.35) 571(8) 0.35 4.84(.10) 362(21)
0.35 4.23(.07) 425(8) 0.49 4.51(.21) 334(18)
# UTS and %EB values presented in this programme are the average value of at least
three measurements. The standard deviation (0) is shown for each sample in the
parenthesis.

TableL3

Effect of draw ratio upon tensile properties at room temperature for


unirradiated and irradiated S3 and P25

UNIRRADIATED SAMPLE IRRADIATED SAMPLE


SAMPLE UTS/MPa %EB SAMPLE UTS/MPa %EB
fDRAWRATIO fDRAWRATIO
S3 S3
1 24.1(.5) 304(29) 1 26.9(1.4) 229(20)
1.23 31.5(1) 215(4) 1.32 34.0(2.3) 207(37)
1.37 33.3(1.2) 193(5.5) 1.44 36.0(.7) 184(15)
1.51 36.3(1.1) 174(14) 1.56 38.0(1.2) 173(12)
1.63 38.0(.5) 172(8) 1.67 39.8(2.7) 166(9)
P25 P25
1 38.8(2.9) 226(19) 1 39.7(1.8) 225(18)
1.35 53.1(2.1) 173(68) 1.35 54.7(1.2) 165(14)
1.63 54.1(1.8) 138(1.4) 1.65 60.1(2) 120(10)
1.9 59.0(1.2) 131(26) 1.93 63.4(1.3) 90(7)
Appendix 191

TableL4
Effect of draw ratio upon tensile properties at room temperature for
un irradiated and irradiated S3 and P2S.

UNIRRADIATED SAMPLE IRRADIATED SAMPLE


SAMPLE UTSlMPa %EB SAMPLE UTSlMPa %EB
IDRAWRATIO IDRAWRATIO
S3 S3
1 2.16(.01) 399(9) 1 4.81(.19) 462(22)
1.22 3.27(.1) 234(3) 1.33 6.24(.2) 348(28)
1.36 3.54(.04) 210(13) 1.45 6.67(.09) 316(26)
1.52 4.22(.01) 203(.7) 1.67 7.08(.16) 286(18)
1.63 4.29(.1) 189(19)
P25 P2S
1 4.12(.09) 265(23) 1 5.46(.24) 326(11)
1.37 6.08(.13) 177(5) 1.35 6.43(.07) 286(16)
1.64 6.38(.2) 137(17) 1.65 7.42(.12) 199(20)
1.9 7.19(7) 124(7) 1.93 8.36(,27) 190(12)

Table LS
Effect of draw ratio upon impact properties for un irradiated and irradiated S3.

UNIRRADIATED SAMPLE IRRADIATED SAMPLE


DRAW PEAK PEAK DRAW PEAK PEAK
RATIO FORCE ENERGY RATIO FORCE ENERGY
N/mm J/mm N/mm J/mm
1 702(22) 5.7(.32) 1 715(25) 5.3(.4)
1.19 848(38) 7.0(.36) 1.17 861(20) 7.3(.24)
1.30 922(11) 8.1(.28) 1.29 965(28) 8.2(.43)
1.44 1033(28) 9.4(.38) 1.44 1069(12) 9.3(.83)
1.63 1149(46) 9.9(,57) 1.56 1178(34) 9.9(,87)
Appendix 192

Table L6
Effect of sample annealing temperature upon percentage gel content for S3

Tanneal %GEL CONTENT


80 37.7
90 34.4
100 34.7

TableL7
Effed of sample annealing temperature upon tensile properties at room
temperature for uni"adiated and i"adiated S3

UNIRRADIATED SAMPLE IRRADIATED SAMPLE


Tannael. UTSlMPa %EB Tanneal. UTSlMPa %EB
DC DC

80 36.3(1.1) 174(14) 80 38.0(2) 173(12)


90 33.4(.8) 184(64) 90 33.4(.8) 166(27)
100 34.7(.1) 197(25) 100 34.7(.1) 160(1.21

TableL8
Effed of sample annealing temperature upon tensile properties at 100 cC
for i"adiated and i"adiated S3

UNIRRADIATED SAMPLE IRRADIATED SAMPLE


Tannael. UTSlMPa %EB Tanneal. UTSlMPa %EB
DC DC

80 4.22(.01) 203(.7) 80 6.67(.09) 316(26)


90 3.9(.4) 222(4) 90 5.8(.2) 280(22)
100 3.68(.2) 208(15) 100 5.6(.1) 244(13)
Appendix 193
ApPENDIXI1

Table ILl
Effect of draw ratio upon density for uni"adiated and i"adiated S3

UNIRRADIATED SAMPLE IRRADIATED SAMPLE

DRAW RATIO DENSITY/wcm' DRAW RATIO DENSITYlwcm'


1.0 1.2372 1.0 1.2431
1.27 1.2380 1.25 1.2431
1.40 1.2388 1.41 1.2429
1.64 1.2359 1.63 1.2428

Ta= 100°Cl I. 5 1.2407

TableIL2
Effect of draw ratio upon x-ray A-peak ratio for uni"adiated and i"adiated
S3andP25.

S3 P25
UNIRRADIATED IRRADIATED UNIRRADIATED IRRADIATED

D.R. A-PEAK D.R. A-PEAK D.R. A-PEAK D.R. A-PEAK


RATIO RATIO RATIO RATIO
1 1 1 1 1 1 1 1
1.23 1.16 1.23 1.2 1.32 1.29 1.32 1.28
1.36 1.26 1.43 1.3 1.56 1.42 1.6 1.42 I
1.7 1.44 1.7 1.42 1.78 1.53 1.8 1.55
Ta=100 Ta=lOO
1.43 1.28 1.43 1.28
Appendix 194

APPENDIX ill

A simple experiment was devised to measure the force exerted due to the
relaxation of orientation during the heating period when oriented specimens were tensile

tested at IOO°C; it is possible that this force may contribute to the overall measured

tensile load. A drawn sample with known thickness and width was placed between the
grips in the tensile testing machine. After a ten minute heating period, the shrinkage force,

specimen thickness and width were measured.

The results for S3 in Table m.I show that the load exerted is very low. This may
be caused by the reordering of the oriented structure that takes place in the sample upon

heating; orientation is retained in the longitudinal (tensile) direction because the sample is

restrained in this direction, but is lost in the transverse direction; the data in table m.2
show that the specimen widths reduce when heated. Therefore equal biaxial orientation is

converted to unequal biaxial or uniaxial orientation after heating. The plot of intended
planar strain, (D.R.)2, against actual planar strain is displayed in Figure HI.

Similar results were obtained for P25, as shown in Tables III.3-4 and Figure

HI.2.

D.R.(*) in Figures 5.9-5.10 is related to intended planar strain as D.R.(*) is the

draw ratio of sample before heating. Hence, [D.R.(*)]2 = intended planar strain.
Appendix 195

TableIILl

UTS and shrinka/fe stress 0 .. unirradiated and irradiated S3


UNIRRADIATED S3 IRRADIATED S3
DRAW UTSat SHRINKAGE DRAW UTSat SHRINKAGE
RATIO 100·C STRESS RATIO 100·C STRESS
lMPa lMPa lMPa lMPa

1.3 3.27 O.oI 1.3 6.24 0


1.5 4.22 0.20 1.5 6.67 0.19
1.8 4.52 0.46 1.8 7.20 0.39

1.5ffa=90·C 3.90 0.27 l.5ffa=90·C 5.80 0.23

1.5ffa=100·C 3.68 0.04 I.5ffa= 100·C 5.60 0

Table IIl2
Planar strain before and after heatin/f of un irradiated and irradiated S3.
BEFORE HEATING AFTER HEATING
D.R. PLANAR THICKNESS wmm mICKNESS WIDTH D.R.* PLANAR
STRAINi Imm ImmJM Imm Imm(B) STRAINa

Unirr.
l.3 I.3x1.3 0.284 2.40 0.368 1.89 1.0 I.3x1.0
1.5 1.5x1.5 0.169 2.40 0.264 1.51 1.0 I.5x1.0
1.8 1.8x1.8 0.227 2.40 0.399 1.33 1.0 1.8x1.0
1.5· 1.5x1.5 0.186 2.40 0.268 1.62 1.0 I.5x1.0
1.5*· 1.5x1.5 0.219 2.40 0.283 1.89 1.2 I.5x1.2

m.
l.3 l.3x1.3 0.234 2.40 0.289 1.91 1.0 I.3x1.0
1.5 1.5x1.5 0.219 2.40 0.319 1.65 1.0. 1.5x1.0
1.8 1.8x1.8 0.197 2.40 0.294 1.53 1.15 1.8xl.lS
1.5· 1.5x1.5 0.213 2.40 0.270 1.95 1.2 1.5x1.2
1.5** 1.5x1.5 0.211 2.40 0.253 2.08 1.3 I.5x1.3

1.5· =Draw ratio for sample annealed at 90°C.


Appendix 196

1.5 **= Draw ratio for sample annealed at 100°C.


D.R. *= Draw ratio in perpendicular direction in tensile bar.[D.R. *=Bx(D.R./A)]
Planar straini = Intended planar strain.
Planar straina = Actual planar strain.

TableIIL3
UTS and shrinkage stress of unirradiated and irradiated P25.
UNIRRADIATED P25 IRRADIATED P25

DRAW UTSat SHRINKAGE DRAW UTSat SHRINKAGE


RATIO 100°C STRESS RATIO 100°C STRESS
/MPa /MPa /MPa /MPa
1.4 6.08 0 1.4 6.43 0.54
1.6 6.38 0 1.7 7.42 0.79
1.9 7.19 0 1.9 8.36 0.98

Table IlL 4
Planar strain before and after heating of un irradiated and irradiated P25.

BEFORE HEATING AFTER HEATING


D.R. PLANAR THICKNESS WIDTH THICKNESS WIDTH D.R." PLANAR
STRAINi !mm !mm !mm !mm STRAINa

unirr.
1.4 1.4x1.4 0.229 2.40 0.349 1.64 1.0 1.4x1.0
1.6 1.6x1.6 0.224 2.40 0.376 1.50 1.0 1.6x1.0
1.9 1.9x1.9 0.306 2.40 0.517 1.37 1.1 1.9xl.l

Irr.
1.4 1.4x1.4 0.224 2.40 0.294 1.83 1.1 1.4xl.l
1.6 1.6x1.6 0.216 2.40 0.329 1.57 1.05 1.6x1.05
1.9 1.9x1.9 0.214 2.40 0.329 1.47 1.15 1.9x1.15
Appendix 197

3.5

1.0

o UNIRR. 83
t.6 IltR. 83
o UNIRR. 83 Ta-90
• 11.1.. 83 Ta-90
C!I UNIRR. 93 T.-100
• 11.1.. 83 Ta-lOO
1.0

to t.t t.2 t.4 t.5 t.8 t.7 u 2.0 2. t


Actual Planar Strain

Figure Ill1 Intended planar strain against actaul planar strain for S3.

4.0

3.5

.9

.,':::3.0
•~

ii:• 2.6
......
u
~
~2.0
~
~

t.6

a UNIRR. P25
)C IRR. P25
to
t.o t.2 t.4 t.' t.8 2.0 2.2
Actual Planar Strain

Figure IIl2 Intended planar strain against adaul planar strain for P25.

You might also like