1.25Gb 20klm SM 1550nm LC (Cisco Coded)

Download as pdf or txt
Download as pdf or txt
You are on page 1of 7

1.

25Gb 20klm SM 1550nm LC (Cisco Coded)


L1-OP3420D-C

PRODUCT DESCRIPTION:

Layer 1 Transceiver is a high performance, cost effective module which


have a Duplex LC optics interface. Standard AC coupled CML for high
speed signal and LVTTL control and monitor signals.

The receiver section uses a PIN receiver and the transmitter uses 1310
nm FP laser, up to 15dB link budge ensure this module 1000Base
Ethernet 20Km application.

KEY FEATURES
♦ Up to 1.25Gb/s Data Links
♦ Hot-Pluggable
♦ 1310nm FP laser transmitter
♦ Duplex LC connector
♦ RoHS compliant and Lead Free
♦ Up to 20 km on 9/125μm SMF
♦ Single +3.3V Power Supply
♦ Monitoring Interface Compliant with SFF-8472
♦ Low power dissipation <1W typically
♦ Commercial operating temperature range: 0°C to 70°C

APPLICATIONS
♦ Metro/Access Networks
♦ 1.25 Gb/s 1000Base-LX Ethernet
♦ 1×Fibre Channel
♦ Other Optical Link

ABSOLUTE MAXIMUM RATINGS


Parameter Symbol Min. Typical Max. Unit
Storage Temperature TS -40 +85 °C
Supply Voltage VCC -0.5 4 V
Relative Humidity RH 0 85 %

RECOMMENDED OPERATING ENVIRONMENT


Parameter Symbol Min. Typical Max. Unit

Case operating Temperature TC °C


Commercial 0 70
Supply Voltage VCCT, R 3.0 3.6 V

ELECTRICAL CHARACTERISTICS (TOP =TC, VCC = 3.0 TO 3.60 VOLTS)


Parameter Symbol Min. Typical Max. Unit Note
Supply Voltage Vcc 3.00 3.30 3.60 V

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved
Supply Current Icc 130 250 mA
Inrush Current Isurge Icc+30 mA
Maximum Power Pmax 1.0 W
Transmitter Section:
Input differential impedance Rin 90 100 110  
Single ended data input swing Vin PP 200 1200 mVp-p
Transmit Disable Voltage VD Vcc – 1.3 Vcc V 2
Transmit Enable Voltage VEN Vee Vee+ 0.8 V
Transmit Disable Assert Time Tdessert 10 us
Receiver Section:
Single ended data output swing Vout,pp 250 1000 mv 3
Data output rise time tr 260 ps 4
Data output fall time tf 260 ps 4
LOS Fault Vlosfault Vcc – 0.5 VCC_host V 5
LOS Normal Vlos norm Vee Vee+0.5 V 5
Power Supply Rejection PSR 100 mVpp 6
Deterministic Jitter Contribution RXΔDJ 51.7 ps 7
Total Jitter Contribution RXΔTJ 122.4 ps
Note:
1. AC coupled.
2. Or open circuit.
3. Into 100 kohm differential termination.
4. 20 – 80 %
5. LOS is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected.
6. All transceiver specifications are compliant with a power supply sinusoidal modulation of 20 Hz to 1.5MHz up to
specified value applied through the power supply filtering network shown on page 23 of the Small Form-factor
Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 14, 2000.
7. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and . DJ.
OPTICAL PARAMETERS (TOP = TC, VCC = 3.135 TO 3.465 VOLTS)
Parameter Symbol Min. Typical Max. Unit Note
Transmitter Section:
Center Wavelength λc 1270 1310 1360 nm 1
Spectral Width σ 3 nm
Optical Output Power Pout -9 -3 dBm 2
Optical Rise/Fall Time tr / tf 260 ps 3
Extinction Ratio ER 9 dB
Deterministic Jitter Contribution TXΔDJ 56.5 ps 4
Total Jitter Contribution TXΔTJ 119 ps
Eye Mask for Optical Output Compliant with Eye Mask Defined in IEEE 802.3 standard
Receiver Section:
Optical Input Wavelength  1260 1360 nm
Receiver Overload Pol -3 dBm 5.6
RX Sensitivity Sen -24 dBm 5.6
RX_LOS Assert LOS A -40 dBm
RX_LOS Deassert LOS D -25 dBm

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved
RX_LOS Hysteresis LOS H 0.5 dB
General Specifications
Data Rate BR 1250 Mb/s
Bit Error Rate BER 10-12
Max. Supported Link Length on 20 km 7
LMAX
9/125μm [email protected]
Total System Budget LB 15 dB
Note:
1. Also specified to meet curves in FC-PI 13.0 Figures 18 and 19, which allow trade-off between wavelength spectral
width.
2. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations.
3. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered.
4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and . DJ.
5. Measured with conformance signals defined in FC-PI 13.0 specifications.
6. Measured with PRBS 27 -1at 10-12 BER
7. Dispersion limited per FC-PI Rev. 13
DIGITAL DIAGNOSTIC MONITOR CHARACTERISTICS
The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless
otherwise specified. It is compliant to SFF8472 Rev10.2 with internal calibration mode. For external calibration
mode please contact our sales stuff
Parameter Symbol Min. Max. Unit
Temperature monitor absolute error DMI_Temp -3 3 degC
Laser power monitor absolute error DMI_TX -3 3 dB
RX power monitor absolute error DMI_RX -3 3 dB
Supply voltage monitor absolute error DMI_VCC -0.1 0.1 V
Bias current monitor DMI_Ibias -10% 10% mA
PIN ASSIGNMENT

Figure2: Diagram of Host Board Connector Block Pin Numbers and Names

PIN DESCRIPTION
Pin No Name Function Plug Seq Notes

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved
1 VeeT Transmitter Ground 1 1
2 TX Fault Transmitter Fault Indication 3
3 TX Disable Transmitter Disable 3 2
4 MOD-DEF2 Module Definition 2 3
5 MOD-DEF1 Module Definition 1 3 3
6 MOD-DEF0 Module Definition 0 3 3
7 Rate Select Not Connected 3 4
8 LOS Loss of Signal 3 5
9 VeeR Receiver Ground 1 1
10 VeeR Receiver Ground 1 1
11 VeeR Receiver Ground 1
12 RD- Inv. Received Data Out 3 6
13 RD+ Received Data Out 3 6
14 VeeR Receiver Ground 3 1
15 VccR Receiver Power 2 1
16 VccT Transmitter Power 2
17 VeeT Transmitter Ground 1
18 TD+ Transmit Data In 3 6
19 TD- Inv. Transmit In 3 6
20 VeeT Transmitter Ground 1

Notes:
1. Circuit ground is internally isolated from chassis ground.
2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
3. Should be pulled up with 4.7k - 10 kohms on host board to a voltage between 2.0V and 3.6V.MOD_DEF(0) pulls line
low to indicate module is plugged in.
4. Rate select is not used
5. LOS is open collector output. Should be pulled up with 4.7k – 10 kohms on host board to a voltage between 2.0V
and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
6. AC Coupled

SFP MODULE EEPROM INFORMATION AND MANAGEMENT


The SFP modules implement the 2-wire serial communication protocol as defined in the SFP -8472. The serial ID
information of the SFP modules and Digital Diagnostic Monitor parameters can be accessed through the I2C
interface at address A0h and A2h.
The memory is mapped in Table 1.
Detailed ID information (A0h) is listed in Table 2.
And the DDM specification at address A2h.
For more details of the memory map and byte definitions, please refer to the SFF-8472, “Digital Diagnostic
Monitoring Interface for Optical Transceivers”. The DDM parameters have been internally calibrated.
Table 1. Digital Diagnostic Memory Map (Specific Data Field Descriptions)

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved
EEPROM Serial ID Memory Contents (A0h)
Data Length Name of
Description and Contents
Address (Byte) Length
Base ID Fields
0 1 Identifier Type of Serial transceiver (03h=SFP)
1 1 Reserved Extended identifier of type serial transceiver (04h)
2 1 Connector Code of optical connector type (07=LC)
3-10 8 Transceiver Gigabit Ethernet 1000Base-LX
11 1 Encoding 8B/10B (01h)
12 1 BR, Nominal Nominal baud rate, unit of 100Mbps
13 1 Reserved (0000h)
14 1 Length(9um,km) Link length supported for 9/125um fibre, units of km
15 1 Length(9um) Link length supported for 9/125um fibre, units of 100m
16 1 Length(50um) Link length supported for 50/125um fibre, units of 10m
17 1 Length(62.5um) Link length supported for 62.5/125um fibre, units of 10m
18 1 Length(Copper) Link length supported for copper, units of meters
19 1 Reserved
20-35 16 Vendor Name SFP vendor name:
36 1 Reserved
37-39 3 Vendor OUI SFP transceiver vendor OUI ID
40-55 16 Vendor PN Part Number: “OPxxxxx” (ASCII)
56-59 4 Vendor rev Revision level for part number
60-61 2 Wavelength Laser wavelength
62 1 Reserved
63 1 CCID Least significant byte of sum of data in address 0-62
Extended ID Fields
Indicates which optical SFP signals are implemented(001Ah = LOS,
64-65 2 Option
TX_FAULT, TX_DISABLE all supported)
66 1 BR, max Upper bit rate margin, units of %
67 1 BR, min Lower bit rate margin, units of %
68-83 16 Vendor SN Serial number (ASCII)
84-91 8 Date code Manufacturing date code
92 1 Diagnostic Type Diagnostics
Enhanced
93 1 Diagnostics
Options
94 1 SFF-8472 Diagnostics
95 1 CCEX Check code for the extended ID Fields (addresses 64 to 94)
Vendor Specific ID Fields
96-127 32 Readable Vendor specific date, read only
128-255 128 Reserved Reserved for SFF-8079

DIGITAL DIAGNOSTIC MONITOR CHARACTERISTICS


Data Address Parameter Accuracy Unit
96-97 Transceiver Internal Temperature ±3.0 °C
98-99 VCC3 Internal Supply Voltage ±3.0 %
100-101 Laser Bias Current ±10 %

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved
102-103 Tx Output Power ±3.0 dBm
104-105 Rx Input Power ±3.0 dBm

REGULATORY COMPLIANCE
The L1-OP3420D-C complies with international Electromagnetic Compatibility (EMC) and international safety
requirements and standards (see details in Table following).
Electrostatic Discharge MIL-STD-883E
Class 1(>1000 V)
(ESD) to the Electrical Pins Method 3015.7
Electrostatic Discharge (ESD) IEC 61000-4-2
Compatible with standards
to the Duplex LC Receptacle GR-1089-CORE
FCC Part 15 Class B
Electromagnetic
EN55022 Class B (CISPR 22B) Compatible with standards
Interference (EMI)
VCCI Class B
FDA 21CFR 1040.10 and 1040.11 Compatible with Class 1 laser
Laser Eye Safety
EN60950, EN (IEC) 60825-1,2 product.

References
1. IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX.IEEE Standards Department, 2002.
2. “Fibre Channel Physical and Signalling Interface (FC-PH, FC-PH2, FC-PH3)” American National Standard for
Information Systems.
3. “Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)”. American National Standard for Information
Systems.
4. Small Form-factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA) September 14, 2000.

Recommended Circuit

Host Board SFP Module


VCC(3.3V) VCCT
4K7 to10KΩ
TX_Disable
TX_Fault

Z=50Ω
Laser
CML Z=50Ω 100Ω
Driver

Z=50Ω

CML 100Ω
Z=50Ω Amplifer

RX_LOS
4K7 to10KΩ
VCC(3.3V)

3X4K7 to10KΩ
MOD_DEF(2)

MOD_DEF(1) EEPROM
MOD_DEF(0)
RGND

Figure 5. SFP Host Recommended Circuit

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved
Mechanical Dimensions

Figure 6. Mechanical Drawing

-------------------------------------------------------------------------------------------------------------------------------------------------------------
[email protected] | www.layer1.net.au
© Copyright 2019 Layer 1 PTY LTD. All Right Reserved

You might also like