Scribd
Upload
507 views2 pages

Text Procedure - How To Install CD

The document provides instructions for installing a CD-ROM drive into a computer. It instructs the user to turn off the computer and unplug it, remove the computer cover, set the Master/Slave jumper on the CD-ROM drive, connect the IDE and power cables to the drive, connect an audio cable if needed, slide the drive into an empty bay in the computer and replace the cover, then turn the computer back on.

Uploaded by

McRizal Blogger
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
507 views2 pages

Text Procedure - How To Install CD

The document provides instructions for installing a CD-ROM drive into a computer. It instructs the user to turn off the computer and unplug it, remove the computer cover, set the Master/Slave jumper on the CD-ROM drive, connect the IDE and power cables to the drive, connect an audio cable if needed, slide the drive into an empty bay in the computer and replace the cover, then turn the computer back on.

Uploaded by

McRizal Blogger
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

How to Install CD-ROM

 Turn off your computer and unplug power cord from power outlet.
 Carefully remove the computer cover.
 Set the Master/Slave jumper on the rear panel of drive.
 Connect the IDE cable to the drive.
 Connect the 4-pole power cable to the drive.
 Connect the audio cable (if applicable).
 Carefully slide the drive into the empty bay and mount it. Then replace the computer cover.
 Plug your computer back to power outlet and then turn the power on.

6. The text above shows us how to ….


a. unpack CD-ROM
b. install the CD-ROM
c. uninstall CD-ROM
d. remove CD-ROM from our computer
e.

7. What is the purpose of the text?


a. To explain how to install CD-ROM
b. To tell the readers how to connect computers using CD-ROM.
c. To discuss the influence of CD-ROM on the computer work.
d. To measure the effectiveness of computer working with CD-ROM installed.
e.

8. What should be done first before installing the CD-ROM?


a. Remove the computer cover
b. Unplug all other devices first
c. Turn off the computer and unplug the power cable
d. Turn the computer on before installing CD-ROM
e.

9. What does the writer strongly recommend in order to get the best result of the CD-ROM installation?
a. That we remove the computer cover first.
b. That the computer should be turned off before installing CD-ROM.
c. That the CD-ROM is set as Master device in the Secondary IDE.
d. That CD-ROM is set as Master device in Primary IDE.
e.

10.We have to connect the CD-ROM to the following types of cable EXCEPT ….
a. power cable
b. audio cable
c. IDE cable
d. monitor cable
e.

11.What part of the CD-ROM should be set if you want to apply CD-ROM as Master or Slave?
a. Motherboard slot
b. IDE slot
c. Cable power
d. Master/Slave Jumper
e.

12.“Connect the audio cable (if applicable).”


The sentence implies ….
a. You may not turn the computer on before connecting the cable.
b. Your CD-ROM may not work properly if you do not connect the cable.
c. It is not necessary to connect the cable if it is not valid
d. Reinstall the CD-ROM if you have not connected the cable.
e.

13.“Connect the IDE cable to the drive.”


The word 'drive' in the sentence refers to ….
a. CD-ROM
b. jumper
c. motherboard
d. computer
e.

14.“Carefully slide the drive into the empty bay and mount it.”
The word 'bay' in the sentence is similar in meaning to ….
a. jumper
b. cable
c. button
d. compartment
e.

15.Plug your computer back to power outlet and then turn the power on.
The word 'outlet' in the sentence is similar in meaning to ….
a. button
b. channel
c. cable
d. port
e.

You might also like