Scribd
Upload
27 views

Assignment 03

1. Machine dynamic class: High speed rotor, Class 1 or 2. 2. Multiplane balancing is required as vibration was measured in two planes (55° and 160°). 3. Balance quality grade of machine: G2.5 (As residual unbalance is less than 2.5% of the maximum permissible unbalance). 4. Permissible specific unbalance for a Class 1 rotor of this size: 0.4 gm-cm/kg. At 50 kg mass, maximum permissible unbalance is 50 x 0.4 = 20 gm-cm. 5. Correction mass from vector diagram: - Plane 1 (55°): 12 x sin55° = 6.6 gm, 12 x cos55

Uploaded by

khans
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
27 views

Assignment 03

1. Machine dynamic class: High speed rotor, Class 1 or 2. 2. Multiplane balancing is required as vibration was measured in two planes (55° and 160°). 3. Balance quality grade of machine: G2.5 (As residual unbalance is less than 2.5% of the maximum permissible unbalance). 4. Permissible specific unbalance for a Class 1 rotor of this size: 0.4 gm-cm/kg. At 50 kg mass, maximum permissible unbalance is 50 x 0.4 = 20 gm-cm. 5. Correction mass from vector diagram: - Plane 1 (55°): 12 x sin55° = 6.6 gm, 12 x cos55

Uploaded by

khans
Copyright
© © All Rights Reserved
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

Yanbu Industrial College

Department of Mechanical Engineering


Technology

Assignment Cover Sheet

Assignment Assignment
Course Code Program Title (Bachelor/Diploma)
Number Due Date
MCET 213
3 MMTP
MET 213
Course Name Lecturer/ Marker’s Name
Equipment Maintenance Muhammad Ajmal

This statement should be completed and signed by the student work in preparation of the
assignment.

Declaration and statement of authorship:


1. I hold a copy of this assignment, which can be produced if the original is lost/damaged.
2. This assignment is my original work and no part of it has been copied from any other student’s work or from
any other source except where due acknowledgment is made.
3. No part of this assignment has been written for me by any other person except where such collaboration has
been authorised by the lecturer/teacher concerned and is clearly acknowledged in the assignment.
4. I have not previously submitted or currently submitting this work for any other course.
5. This work may be reproduced and/or communicated for the purpose of detecting plagiarism.
6. I give permission for a copy of my marked work to be retained by the College for review by external
examiners.
7. I understand that plagiarism is the presentation of the work, idea or creation of another person as though it is
your own. It is a form of cheating and is a very serious academic offence that may lead to expulsion from the
College. Plagiarised material can be drawn from, and presented in, written, graphic and visual form, including
electronic data, and oral presentations. Plagiarism occurs when the origin of the material used is not
appropriately cited.
8. Enabling plagiarism is the act of assisting or allowing another person to plagiarise or to copy your work.

Student Submission
Student name ID Section
Signature Date

Lecturer/ Marker’s Name and Comments Grade Course Learning Outcomes (CLO’s)
Muhammad Ajmal

MCET Department Reviewed 5 Jan 2018


Q1: An eight blades fan with mass 50 kg having diameter of 350 mm, width 50mm is running CCW
at 2000 rpm. The first blade is at zero degree and motor power is 5kw. The following vibration data
was collected in the field during balancing process. Perform balancing of rotor using Vector
Method.
First Run: V = 12mm/s, at 55 degrees
Trial Run: V = 7 mm/s at 160 degree
Final Run: V = 5mm/s
ANSWER the following:
1- Machine dynamic class
2- Single or multiplane
3- Balance quality grade of machine
4- Permissible specific unbalance
5- Correction mass and its position
6- Perform trim balancing (if required)
7- Weight splitting (if required)
8- Sketch your balancing set-up

You might also like