EVO-ONE ALL-IN-ONE DATA INTERFACE

REMOTE STARTER / ALARM

QUICK INSTALLATION GUIDE
WIRING / CONNECTION GUIDE GUIDE # 68451
(20-PIN) SECONDARY CONNECTOR (3-PIN) SHOCK SENSOR
A1
(+) Foot Brake Black IN IN Yellow (+) BYPASS IGNITION (2-PIN) Valet/
Programming Button
750mA (-) Parking lights Pink OUT OUT Purple (-) LOCK 750mA
750mA (-) Trunk Release/AUX Yellow/Black OUT OUT Purple/White (-) UNLOCK 750mA
(-) Hand Brake Brown/White IN OUT Green (-) IGNITION 750mA G
(-) Hood/Door Pink/Black IN OUT White (-) START 750mA White
F
Bypass config. Purple/Yellow OUT Orange (-) DISARM 750mA
Black
Bypass config. Green/White OUT Orange/Black (-) HORN/SIREN 2 Amp
Bypass config. Green/Red OUT Dk.Blue (-) GWR/PROGRAMMABLE 750mA
A20 A
Bypass config. White/Black OUT IN Red/Blue BYPASS CONFIG.

White
Bypass config. Lt.Blue Lt.Blue/Black BYPASS CONFIG.
750 mA MAXIMUM OUTPUT. DO NOT EXCEED THE MAXIMUM CURRENT OR PERMANENT DAMAGE TO THE MODULE WILL OCCUR THAT WILL NOT BE COVERED
UNDER WARRANTY.
(6-PIN) POWER CONNECTOR E1
OUT White (+) PARKLIGHTS/IGN2/ACC/START
Ground Black IN PROGRAMMABLE OUTPUT (FUNCTION 2 & 31)
E

(+) Ignition Pink OUT (+) ACC / IGN2 White

OUT Orange
PROGRAMMABLE OUTPUT (FUNCTION 2 & 31)
(+) Starter Yellow OUT IN Red (+) 12V
E6
LED Blue CAN ACTIVITY
LED Yellow IGNITION ON
LED Red BYPASS DATA

D C B Blue H I J
Red White Blue Black CUT LOOP FOR download the
AUTOMATIC
TRANSMISSION specific vehicle
MODE.
installation guide at:

(6-PIN) BYPASS RELAY

REMOTE STARTER PROGRAMMING LED FORTIN.CA
BYPASS PROGRAMMING BUTTON
(5-PIN) CAN-BUS (4-PIN) RS-232 DATA-LINK & FLASH-LINK UPDATER PORT
(4-PIN) DATA-LINK ANTENNA (4-PIN) ANTENNA PAGE 1

Downloaded from www.Manualslib.com manuals search engine

 PROGRAMMING REMOTE TRANSMITTER(S)
The system can learn up to a maximum of 4 transmitters.
Any transmitters can be stored in more than 1 memory slot.
When a 5th transmitter is learned the 1st remote is erased (FIFO).

STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6

WITH IGNITION SWITCH

FMH
2-W Press and
release FMH
Turn the Ignition Turn the 2 -W
the brake
OFF. Ignition ON.
pedal four
The LED
will turn
x4 times.
ON.

On each Transmitter press

and release the button
WITH VALET SWITCH

Turn Press and hold the Press and release the valet Press and The then press and release the Turn the
the valet switch until switch five time. release LED button. Ignition
Igni- the parking lights The parking lights will flash the brake will OFF to exit
tion turn ON, the horn/ and the horn/siren will chirp pedal flash program-
ON. siren will chirp. each time to confirm. x1 once. rapidly. The LED will stop ming.
x5 FM H
2-W flashing for a
second confirming
programming.

ERASES ALL REMOTES THAT HAVE BEEN PROGRAMMED AND RESETS ALL FUNCTIONS BACK TO DEFAULT.
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Disarm
the system
(The OR Press and
OR Press OR Press and
hold the
Turn the
Ignition
antenna Turn and
hold the valet Press valet switch OFF
led must the release
switch or the and or the to exit
not be
flashing,
Ignition
ON.
antenna but-
ton until the
the valet
switch X1 release
the
antenna
button for
program-
ming.
see enter/ or the
5 seconds.
FMH FMH FMH

Parking lights brake- The

2-W 2-W 2-W

exit valet antenna

turn ON, the pedal The Parking Parking
mode button
horn/siren once. lights will lights
p.6). will chirp.
23 flash to will flash
Within 5 sec. TIMES. confirm. 4 times.

PAGE 2

Downloaded from www.Manualslib.com manuals search engine

 FUNCTION PROGRAMMING
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
MODE 1 - LOCK
Disarm
the MODE 2 - UNLOCK
system FMH
2-W
FMH
2-W
FMH
2-W X1 MODE 3 - START (3 SECONDS)
(The
antenna MODE 4 - FUNCTION (3 SECONDS)
led
must
OR OR MODE 5 - FUNCTION LOCK
not be MODE 6 - FUNCTION UNLOCK
flash- Turn the Press and hold the The Press and release the valet Press and Turn the
ing, see Ignition valet switch or the LED will switch or the antenna but- release the Ignition
enter/ ON. antenna button flash ton X time for the desired brake- Press the BUTTON on a programmed remote to select the OFF to exit
exit until the Parking rapidly. function. The Parking lights pedal mode (X). program-
valet lights turn ON, will flash and the horn/ once. The Parking lights will flash 1-6 times to confirm. ming.
mode Within 5 sec. the horn/siren will siren will chirp each time The Park-
p.6). chirp. to confirm. ing lights
will flash
4 times.
Return to step 3 to programmed the next option

FUNCTION
FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6
1 — — — — — — —
White (+)Ignition2 White (+)Accessory2 White (+)Start2 White (+)Start
Programmable Output
(+) Ign/Acc/Start Orange (+)Accessory Orange (+)Accessory Orange (+)Accessory Orange (+)Ignition2
2 — —
(FUNCTION 31 Pink (+)Ignition Pink (+)Ignition Pink (+)Ignition Pink (+)Ignition
MODE 4)
Yellow (+)Start Yellow (+)Start Yellow (+)Start Yellow (+)Start2

3 Tachless sensivity Increase (By default) Decrease

crank time crank time

Remote car starter Gas: 15 minutes Gas: 7 minutes Gas: 3 minutes

4 — — —
runtime Diesel: 30 minutes Diesel: 14 minutes Diesel: 6 minutes
Add Remote on FMH
5 antenna series Add Remote — — — — —

Unlock before remote-start & Unlock and relock after Relock 10 sec.after Disarm before shut
6 Doorlock option No Lock after remote-start.
Lock after remote-start. shut-down. shut-down. down.
Lock after foot-brake & Unlock after key is turned Doorlock Output at Ignition
7 Ignition Doorlock option No — —
unlock after key is turned OFF. OFF. only.
8 Unlock Pulse Time Single 0.25 sec Double 0.25 sec Single 4.0 sec Single 2.5 sec Single 1.5 sec Single 0.75 sec
Passive (Lock disabled) Passive (Lock enabled)
Active Arm alarm activate starter-kill Arm alarm, activate starter-kill Passive arm Passive arm Passive arm 120
Active or Passive Alarm
9 & Starter Kill. Press LOCK to activate 30(MODE 4), 60(MODE5), or and lock doors 30(MODE 4), 30 seconds (by default if 60 seconds. (if MODE seconds. (if MODE 2
the Alarm and starter-kill. 120(MODE6) sec. after the door 60(MODE5), or 120(MODE6) MODE 2 or 3 is activated. 2 or 3 is activated. or 3 is activated.
is closed. sec. after the door is closed.

Downloaded from www.Manualslib.com manuals search engine

 FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6
Starter Kill Output.
10 Required function 32 Starter-kill &anti-grind Anti-grind only Relay normally open — — —
mode 4. - Dk.Blue (A8)
= starter-kill.

1st LOCK/UNLOCK silent

Sound Confirmation
2nd LOCK/UNLOCK sound LOCK/UNLOCK Antenna LED disabled with Confirmation sound at
11 & LED antenna --------------------------- sound always. Antenna LED disabled. ignition. LOCK only Panic mode disabled
Antidémarreur Antenna LED active.

Output horn/siren Siren(+) Output (E1) white

12 configuration Horn(-) only. Siren(+) Output (E1) white and Horn(-) Siren(-) only (A7) — —

13 Confirmation Pulse Long Short — — — —

14 Alarm ON/OFF Alarm OFF Alarm ON Alarm ON — — —

Starter ON/OFF Remote-starter ON Remote-starter ON. Remote-starter OFF
(Unlock signal) Automatically
Smart Arming LOCK and rearm alarm if Automatic Lock when starter Lock pulse only when its
15 Smart Doorlock Disable door(s) are not opened after kill arms. Unlock — —
Smart Lock pulse
30 seconds.
16 Cold Start Timer 3 hours at -5oc/Runtime 1.5 hours at -5oc/Runtime 3 hours at -5oc/5 minutes 1.5 hours at -5oc/5 minutes Cold time OFF —
17 — — — — — — —
Enable (20 seconds) Enable (10 seconds) Enable
18 Diesel Mode Disable Delay between Ignition Delay between Ignition No delay between Ignition — —
power up and Starter (crank). power up and Starter (crank). power up and Starter (crank).

19 Turbo timer Disable Run 2 minutes. Run 4 minutes. — — —

Engine supervision: Tachless on crank Tachless only. Start (Crank) 20 sec + Start (crank) 8 seconds Start (Crank) 8 sec +
-Tachless - on Tachless.
20 and supervision Tach ( vehicles with automatic Supervision by Supervision by Tach Data-Link only
-analog tach- ( vehicles with automatic
-Tach Data-Link- Data-Link. transmission only) Data-LInk Tach transmission only) Data-LInk Tach

21 Start Attempts 2 1 3 — — —
22 — — — — — — —
RESET all programming
options by default.
23 Master RESET (Retains already — — — — —
programmed remote.)
24 — — — — — — —

Yellow/Black (A13) : 30 sec latch or

0.5 seconds & 10 sec latch or 20 sec latch or
25 disarm alarm 0.5 seconds until a button is pressed. until a button is pressed. until a button is Latch until shutdown
Aux1 --> LOCK pressed.
26 Hybrid mode Gas / Diesel vehicle Hybrid vehicle — — — —
27 — — — — — — —
28 — — — — — — —
29 Alarm Duration 30 seconds 60 seconds 120 seconds — — —
Ignition ON
Ignition ON Ignition ON Ignition ON Ignition ON
Ignition ON Valet button x6
30 Valet code Valet button x3 times. Valet button x3 times Valet button x4 times Valet button x5 times times and x1 times Valet button x7 times
and x1 times 3 seconds. and x1 times 3 seconds. and x1 times 3 seconds. and x1 times 3 sec.
3 seconds.

Downloaded from www.Manualslib.com manuals search engine

 FUNCTION MODE 1 MODE 2 MODE 3 MODE 4 MODE 5 MODE 6

Special application - Function 2 (all option) (+) Parking (+) Parking White:(+) Parking-
White Lights White Lights Lights
not available.
Special application No special application Orange (+) Accessory Orange Ign.2 Orange:(+) Parking
31 lights
Programmable output (+) Priority on function 2 White wire (E1) : Enable at
ground out, disable with vehicle White wire (E1) : Trunk
Output Pink (+) Ignition Pink Ign.1 Pink:(+) Ignition
ignition OFF.
Yellow (+) Start Yellow (+) Start Yellow:(+) Start
Dk.Blue (Ground out): Dk.Blue (Ground out): Dk.Blue D.k Blue D.k Blue
32 Controlled by CAN
Ground Out Shut-down 1 second after Shut-down 3 seconds after (Ground Out): (Ground Out): (Ground Out): learning
remote start run time. remote start run time. Shutdown After Starter-Kill Arm / Rearm
Manual transmission Manual transmission Automatically activated by hand- Manual sequence completed Cancel ready mode when
33 function completed by door closed. brake and Foot Brake by locking the doors trunk open. — —

Unlock before trunk pulse

34 Trunk output Pulse 0.5 seconds Pulse 2.5 seconds Trunk Output at ignition only — —
0.5sec
Door unlock Special Activate vehicle ignition at Activate vehicle ignition and
35 application No special application unlock. accessory at unlock. — — —

Activation/desactivation by remote : FUNCTION -->

36 — By Valet button only — — —
remote Valet Mode LOCK + UNLOCK or valet button

Security Remote car Security ON: Shutdown Engine

37 starter No special application if the door is opened before — — — —
UNLOCK is pressed. (Door
Special application trigger required).
System control by OEM Start/Stop on trigger shock Alarm control by OEM Press Lock, Unlock
38 Remote Disable Press 3x Lock to remote start sensor Remote. Lock to remote start —

Enable : AUX1 activated at

39 Temperature option Disable 5oc when remote started (see — — — —
function 25)
LEGEND: FUNCTION BY DEFAULT

MANUAL TRANSMISSION SEQUENCE FOR COMPATIBLE VEHICLES ONLY

STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6
Remove the
Push the Exit the vehicle
Make sure that key from
While the START button and close all
all doors are the ignition
engine is (3sec.). of the doors.
closed and the Release barrel.The
running. The Parking The Remote-
transmission the brake vehicle
Engage the lights will Starter will stop
& is in the
parking
pedal.
flash once and
will remain
running once
NEUTRAL running with
brake. then remain all the doors
position. the Remote-
on. are closed.
Starter.

WILL DISABLE MANUAL TRANSMISSION SEQUENCE

STANDARD • Open the hood Note : If the Parking lights flash 3 times when
• Open any door(s) • Disengage the parking brake Remote-Starting, Ready Mode is not enabled.

PAGE 5

Downloaded from www.Manualslib.com manuals search engine

 TO ENABLE COLD START MODE TO DISABLE COLD START MODE
• Put the Remote-Starter/alarm into Valet
Press and release the FUNCTION button, • Press and release the FUNCTION button, • Remote-Start the vehicle
within 12 seconds simultaneously press and within 12 seconds simultaneously press • Open the hood
+ and hold the LOCK and START buttons for 1 and and hold the LOCK and START buttons for • Press the brake pedal
second. The parking lights will flash once. 1 second. The parking lights will flash twice. • Turn the key to the ignition position.
• Disable Ready Mode (manual transmission).

DISARM / ENTER / EXIT VALET MODE

STEP 1 STEP 2
Within
to disarm FMH
System armed
OR 10 seconds FM H
System dis-
armed :
2 -W 2 -W

the system : DEL flash press and LED is OFF

3x 3x release
the Valet
Insert the key switch or System disarmed
to enter and System and turn it to the
FM H
2-W
the antenna
FMH
and in valet
exit valet disarmed :
FMH 2 -W
2-W

ignition (ON/RUN) mode :

mode LED is OFF position. button
LED is ON.
3 TIMES.

REMOTE START DIAGNOSTICS ALARM DIAGNOSTICS

Parking Lights flashes (before starting) : Parking Lights flashes (after Shutdown) : Parking Lights flashes (after disarm) :
3x Ready mode disabled 1x Normal stop (Brake, Park Brake) 3x Door open – zone 3
4x Valet mode activated (The LED is on) 3x Runtime expired or shut down by transmitter 4x Shock sensor – zone 4
5x Hood open 4x No tachometer signal 5x Hood open – zone 5
5x Hood open 6x Trunk open – zone 6
6x Over crank threshold (8 seconds)

WARNING
NOTICE The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of the product, including either damage to the vehicle
itself or to the remote-starter module. This module must be installed by a certified technician including all of the supplied safety devices. Please note that this guide
has been written for trained professional technicians, a certain level of skills and knowledge is therefore assumed. Please review the Installation Guide carefully before
beginning any work.
WARNING By default this system is setup for vehicles with a manual transmission. For vehicles with an automatic transmission the safety wire loop on the main unit must
be cut. Before proceeding to the installation, make sure that the vehicle does not attempt to start when the when the vehicle is in the “drive” or “reverse” position. If an
automatic transmission vehicle starts when the transmission is in gear, ensure that the safety wire loop on the unit is not cut. Once the safety wire loop is cut, the system
is considered an automatic transmission remote-starter indefinitely. Once a loop is cut all warranties, guaranties, and liability is immediately void if the unit is install on
a manual transmission vehicle.Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module,
except for the replacement of this module in case of manufacturing defects. This module must be install by qualified technician. This instruction guide may change
without notice. To download the installation guide, user guide, or the latest quick installation guide, visit: WWW.FORTIN.CA
Technical support: TEL: 514-255-4357 / 1-877-336-7797
Copyright © 2014-2017, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED MADE IN CANADA REV.:20171017
PAGE 6

Downloaded from www.Manualslib.com manuals search engine