22ESC143/243

Model Question Paper-1/2 with effect from 2022-23 (CBCS Scheme)

USN

First/Second Semester B.E. Degree Examination

Subject Title Introduction to Electronics Engineering (MCQ)
TIME: 01 Hours Max. Marks: 50

Note: 01.
02.
03.

Q.01 L1 Rectifier converts

a)AC to DC b) DC to DC c) DC to AC d)AC to AC
2 L1 For a step down Transformer turns ration should be
a)N2>N1 b)N1< N2 c)N1=N2 d) N1≠N2
3 L2 BJT acts as a switch in
a)Cutoff and Active region b)Active and Saturation region c)Active and cutoff region d)Cutoff
and Saturation region
4 L1 Component of a Smoothing Filter
a) Resistor b)Capacitor C)Diode D)Transformer
5 L1 Bridge wave rectifier uses ______ number of Diodes to get Rectified output
a)1 b)2 c)4 d)3
6 L2 Multi Stage Amplifier Over gain will be
a) Av1 + Av2 + Av3 b)Av1*Av2*Av3 c) Av1/Av2/Av3 d)Av1-Av2-Av3
7 L2 A circuit that amplifies the difference between two signals is called
a)Differential Amplifier b)Operational Amplifier c)Buffer d)Transistor
8 L1 Negative feedback in an Amplifier
a) Reduced gain b)Reduces bandwidth c)Increase noise d)increase frequency
9 L1 Op Amp as a Voltage Follower has a Voltage Gain of
a)Zero b)Unity c)Negative value d)less than unity
10 L1 Ideal Op-Amp has following characteristics
a)Rin=∞, A=∞,Ro=0. b) Rin=0, A=∞,Ro=0. c) Rin=∞, A=∞,Ro=∞ d) Rin=∞,
A=∞, Ro=∞.
11 L1 An oscillator produces ______________________ oscillations
a)Damped b)UnDamped c) Modulated d)none of thee
12 L1 An oscillator employs __________ feedback
a)Positive b)Negative c)both d)none
13 L1 In a Phse shift Oscillator we use ________ RC sections
a)2 b)3 c)4 d)5
14 L1 The Piezeo electric effect in a crystal is _______
a)A voltage developed because of mechanical stress
b)A change in resistance of temperature
c) A change in frequency of temperature
d)none
15 L1 If crystal frequency changes with temperature, we say that crystal has _________ temperature
coefficient
a)negative b)zero c)none d)Positive
16 L1 Crystal oscillator frequency is very stable due to ___________ of the crystal
a)Rigidity b)Vibrations c)Low Q d) High Q
17 L1 An Oscillator differs from an amplifier because it ________
a)Has more gain b) requires no input signal c)requires no DC supply d)Always has same
input

Page 01 of 03
 22ESC143/243

18 L1 Q of a crystal is of the order of __________

a)100 b)1000 c)50 d)>10K
19 L1 Signal Generator generally used in laboratories is _________ oscillator
a)Hartely b)Wein bridge c)Crystal d)Phase shift
20 L2 In boolean algebra, the OR operation is performed by which properties?
a) Associative properties
b) Commutative properties
c) Distributive properties
d) all the above
21 L1 The expression for Absorption law is given by ________
a) A + AB = A
b) A + AB = B
c) AB + AA’ = A
d) A + B = B + A
22 L3 Complement of the expression A’B + CD’ is _________
a) (A’ + B)(C’ + D)
b) (A + B’)(C’ + D)
c) (A’ + B)(C’ + D)
d) (A + B’)(C + D’)
23 L3 Simplify Y = AB’ + (A’ + B)C.
a) AB’ + C
b) AB + AC
c) A’B + AC’
d) AB + A
24 L1 Canonical form is a unique way of representing ____________
a) SOP
b) Min term
c) Boolean Expressions
d) POS
25 L3 How many gates are required to implement the following Boolean function
xy+x(x+z)+y (x+z)
a)1 b)2 c)4 d)5
26 L2 The process of reduction of circuit will _____________ cost of circuit
a)not change b)increase c)decrease d)none
27 L1 Boolean algebra can be used ____________
a) For designing of the digital computers
b) In building logic symbols
c) Circuit theory
d) Building algebraic functions
28 L2 F(X,Y,Z,M) = X`Y`Z`M`. The degree of the function is ________
a) 2 b) 5 c) 4 d) 1
29 L1 What are the canonical forms of Boolean Expressions?
a) OR and XOR
b) NOR and XNOR
c) MAX and MIN
d) SOM and POM
30 L1 The ___________ of all the variables in direct or complemented from is a maxterm.
a) addition
b) product
c) moduler
d) subtraction
31 L1 Which type of memory is suitable for low volume production of embedded systems?
a) Non-volatile
b) RAM
c) Volatile
d) ROM

Page 02 of 03
 22ESC143/243

32 L1 How an embedded system communicate with the outside world?

a) Memory b) Output c) Peripherals d) Input
33 L1 Which of the following helps in reducing the energy consumption of the embedded system?
a) emulator b) debugger c) simulator d) compilers
34 L1 Which of the following is the pin efficient method of communicating between other devices?
a) memory port
b) peripheral port
c) parallel port
d) serial port
35 L1 Which of the following unit protects the memory?
a) memory management unit
b) peripheral unit
c) execution unit
d) bus interface unit
36 L1 Which of the following statements are true for von Neumann architecture?
a) separate bus between the program memory and data memory
b) external bus for program memory and data memory
c) external bus for data memory only
d) shared bus between the program memory and data memory
37 L1 Sensors are used across _____________ of embedded system.
a)input b)output c)Processing the data d)none
38 L1 An Embedded system is a combination of ______.
a)software b)hardware c)both d)devices
39 L1 An Embedded system is classified in to how many types
a)1 b)2 c)3 d)4
40 L1 USB used for ____________ data
a)sending b)storing c) receiving d)deleting
41 L2 In FM the ____________ of the information signal modulates the frequency of carrier signal
a)Amplitude b)Frequency c)phase d) all
42 L1 Modulation is of ____________ types
a)Analog Modulation b)Digital Modulation c)Pulse Modulation and spread spectrum
modulation d)all
43 L1 Function of Modulator is _____________
a)Modulates the signal b)Demodulates the signal c)maintains the signal d)none
44 L1 Which type of modulation is used for radio transmission in India?
a)Amplitude modulation b)Frequency Modulation c)Phase Modulation d)none
45 L1 Bandwidth is expressed in terms of __________.
a) Bits per second b) Hertz c) Centimeters d)seconds
46 L1 Modulation index gives the ratio of ________.
a) Carrier voltage and voltage of Modulating signal
b) the voltage of Modulating signal and the un-modulates signal voltage
c) The voltage of Modulating signal and carrier voltage
d) none
47 L1 Signal is represented in _________ domains.
a) Time domain b) Frequency domain c) Both a and b d)none
48 L1 What are the units of modulation rate?
a)Seconds b) Baud c) Meters d) Centimeters
49 L1 On which component modulation is performed?
a) Transmitter and Receiver b) Signal c)Zammer d)none
50 L1 The standard form of PAM is _________
a) Pulse Amplitude Modulation b) Phase Amplitude Modulation c) Positive Amplitude
Modulation d) None of the above
*Bloom’s Taxonomy Level: Indicate as L1, L2, L3, L4, etc. It is also desirable to indicate the COs and POs to be
attained by every bit of questions.

Page 03 of 03