Scribd
Upload
93 views

Quick Setup Guide

The document provides instructions for connecting an ADSL router and setting up TCP/IP in Windows. It describes connecting the router via an Ethernet cable to the computer and a phone line. It then gives steps for setting up TCP/IP in different Windows operating systems. The document also provides options for automatically or manually setting up the router via the setup CD and configuring connection settings.

Uploaded by

jemscaburn
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
93 views

Quick Setup Guide

The document provides instructions for connecting an ADSL router and setting up TCP/IP in Windows. It describes connecting the router via an Ethernet cable to the computer and a phone line. It then gives steps for setting up TCP/IP in different Windows operating systems. The document also provides options for automatically or manually setting up the router via the setup CD and configuring connection settings.

Uploaded by

jemscaburn
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

Contents

I. II. Connection the ADSL Router.....P3 Set up TCP/IP in Windows...P4


1. For Windows ME/98.P4 2. For Windows XP/2000..P6

III. Set up the router...P7


1. Setup Router Automatically....P7 2. Setup router manually..P9

Router Front Panel

LED Indicators The LED Indicators read as follows:

POWER READY

Steady light indicates the router is on. When blinking indicates system is functioning Steady light indicates a valid ADSL connection. The light will be steady after the ADSL negotiation process has been settled. Blinking light indicates an active WAN session. Steady light indicates a valid Ethernet connection. Blinking lights indicates an active Ethernet session. Reset to Factory Default

ADSL

DATA LINK ACT RESET

I. Connection the ADSL Ethernet Router


Requirements: You must have an Ethernet network card installed. You must have the Windows TCP/IP protocol properly setup. You must connect cables properly.

Ethernet Network ( LAN ) Port x 4 USB Port Wan Port On/Off

Power cord
( Plug the power cord into the power outlet. )

Phone cable
( Plug the other end of the phone line cable into the phone jack. )

Ethernet cable
( Plug the other end of the Ethernet cable into the Ethernet port on the NIC.)

Set up TCP/IP in Windows


1. For Windows ME/98
Step 1: Right Click on My Network Places to highlight it and select Properties on the Desktop. i diagram 1j

Step 2: The Network dialog box will open. Click on Internet Protocol ( TCP/IP ) to highlight it and then click on Properties.i diagram 2j

Step 3: The TCP/IP Properties dialog box will open, in IP address section, select Obtain an IP address automatically. i diagram 3j

Step 4: Click on Gateway, and in Gateway section, erase all previous settings. Step 5: click on DNS configuration, then select disable DNS. Step 6: click OK to close all networking dialog boxes. i diagram 4B 5j

2. For Windows XP/2000


Step 1: Click on the Start button and select Settings then click on Control Panel. Step 2: Click on Network Connections to open the network control panel. Step 3: Right Click on the Local Area Connection to highlight it and select Properties. i diagram 6j

Step 4: The local Area Connection Properties dialog box will open. Click on Internet Protocol (TCP/IP) to highlight it and then click on Properties.i diagram 7j

Step 5: In Properties dialog box, select Obtain an IP address automatically and Obtain DNS Server address automatically, then chick OK for all the subsequent dialog boxes to save the settings.i diagram 8j

8
6

II. Set up the router


When you set up the PAE-CE81/84, please power on. Insert the Driver CD into the CD-ROM drive then double click the setup icon. Driver will be automatically display a Paradigm Technology Inc Window.

Setup Router Automatically: Use the ISP default setting. (RECOMMENDED) Setup Router manually: Advance setting. (You have to setup all setting by yourself) View Current Settings: Show the current Router setting. Exit: Exit setting.

1. Setup Router Automaticlly


Step 1: Select your country.

Step 2: Select your ISP. ( Some country does not need this selection )

Step 3: If your ISP provides you username and password, please fill in this dialog. Otherwise skip this step.

Step 4: Summary of router settings being done, please confirm the settings to your ISP.

Step 5: Please turn off and then turn on your PAE-CE81/84 again. This step will refresh the previous settings of your router. And you can close the set-up window.

Step 6 : Now the router set-up is complete, please wait 3 minutes for the routers to establish adsl connection with ISP, Then open your browser now to see if the ADSL connection has been established.

2. Setup router manually (Advance setting)


Step 1: You must select encapsulationB handshake and input the VPI/VCI setting which your ISP provide for you. ( Some ISP doesnt need to input VPI/VCI ).

Step 2: a. If you are using 1483 Routed LLC, 1483 Routed VC-MUX and 1577 IpoA , you need to input the IP setting (Static IPB Subnet Mask and Gatway)

b. If you are using PPPoA LLC, PPPoA VC-MUX, PPPoE LLC and PPPoE VC-MUX, you need to input username and password. User name and password is advised to you by your ISP.

Step 3: Summary of the router settings being done, please check the settings to your ISP.

Step 4: Please turn off and then turn on your PAE-CE81/84 again. This step will refresh the previous settings of your router. And you can close the set-up window.

Step 5 : Now the router set-up is complete, please wait 3 minutes for the routers to establish adsl connection with ISP, Then open your browser now to see if the ADSL connection has been established.

10

You might also like