VW Passat b5 70-1 Instrument Panel

Download as pdf or txt
Download as pdf or txt
You are on page 1of 13

70-1

Instrument panel
Instrument panel, removing and installing
CAUTION! Before working on the electrical system; disconnect battery Ground (GND) strap. Removing Note: Before disconnecting the battery, obtain radio anti-theft code. - Remove center console page 68-10 . page 69-

- Remove airbag unit driver side 38 .

- Remove hex head bolt -2- (60 Nm - must be replaced). - Place steering wheel-1- in center position (wheels straight ahead). - Remove steering wheel -1- from steering column.

70-2

- Unscrew two Phillips-head screws (arrows) - Remove upper trim for steering column switch -1-

- Unscrew four Phillips-head screws (arrows) - Unscrew inner hex head bolts -1-. - Release height adjustment for steering wheel -2-. - Remove lower trim for steering column switch -3-

70-3

- Loosen inner hex head bolt -1-. - Remove connectors (arrows) from steering column switch. - Remove steering column switch

- Pry off cover cap -1- Unscrew bolts -2- and -3-. - Unclip lower A-pillar trim -4- from sill plate and remove.

70-4

- Unclip -1- cover. - Unscrew bolts (arrows). - Remove shelf driver side -2-. - Remove connector from light switch -3- and from adjuster for automatic vertical aim control system -4-.

- Slide cover -1- upward and secure with tooling aid (e.g. screwdriver handle) -2-. - Remove four screws (arrows). - Remove cover -3-.

70-5

- Remove two bolts (arrows) - Remove instrument cluster. - Disconnect connector.

- Remove two bolts (arrows)

70-6

For the removal of the radio use tool for radio 3316. The unlocking tool for radio 3316 consists of two similar individual parts.

- Insert unlocking tool for radio 3316 in the slot (arrows) until it unlocks

70-7

- Remove radio at handles of tool from instrument panel. Notes: Release tool for radio 3316 should not be pushed to the side or tilted. To remove the tool the side tabs on the radio must be pressed inward. - Remove connector.

- Unclip -1- trim.

70-8

- Unscrew eight bolts (arrows) - Remove cover dash panel center cover -1- and take out connector.

- Remove five screws (arrows).

70-9

Note: If reinstalling the same dash panel, disconnect connector -3- and leave outlets -2- and wiring installed. - With a flat screwdriver -1- release three clips (arrows). - Maintain tension of outlets -2-, in order to avoid clips from locking again. - Remove outlets -2- from dash panel and disconnect connector -3-.

70-10

- Unscrew bolt (arrow) - Remove trim -1-.

- Pry off cover cap -1- Remove screws -2- and -3-. - Unclip lower A-pillar trim passenger side -4- from sill plate and remove.

70-11

- Unscrew bolts (arrows) - Open glove compartment -1-.

- Unscrew bolts (arrows) - Carefully pry out light for glove compartment -1- with a screwdriver, from the top and remove connector -2-.

70-12

- Remove glove compartment liner -1- from instrument panel.

- Pry off cover -1-.

70-13

- Unscrew hex bolts (arrows). - Disconnect connector -1-. - Lift out instrument panel Installing - Install in reverse order of removal. Notes: After disconnecting the battery make sure that the vehicle equipment (radio, clock and power window regulators) are checked according to repair manual and/or operating instructions. If warning light (K75) for airbag signals a malfunction after assembly, erase DTC memory with Scan Tool V.A.G 1551 and check again. Repair Manual, Body On Board Diagnostic (OBD), Repair Group 01

You might also like