Scribd
Upload
42 views

Plate Rectangular

This document summarizes the analysis of deflection for a simply supported rectangular plate with uniform and concentrated central loading. It provides the plate dimensions, material properties, loading conditions, and results from the analysis. The analysis uses equations from Roark's Formulas for Stress and Strain to calculate deflection at the center of the plate and maximum bending stress for different a/b ratios representing variations in plate geometry. Graphs of the non-dimensional coefficients beta, alpha, and gamma are given to allow interpolation of deflection based on a/b ratio. Numerical results from the analysis match those of a ProE simulation.

Uploaded by

Reyginald Marron
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
42 views

Plate Rectangular

This document summarizes the analysis of deflection for a simply supported rectangular plate with uniform and concentrated central loading. It provides the plate dimensions, material properties, loading conditions, and results from the analysis. The analysis uses equations from Roark's Formulas for Stress and Strain to calculate deflection at the center of the plate and maximum bending stress for different a/b ratios representing variations in plate geometry. Graphs of the non-dimensional coefficients beta, alpha, and gamma are given to allow interpolation of deflection based on a/b ratio. Numerical results from the analysis match those of a ProE simulation.

Uploaded by

Reyginald Marron
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 7

Plate_Rectangular.

xls
To determine deflection of a simply supported rectangular plate
By Alex Slocum, 01/01/04, last modified 09/21/04 by Xue'en Yang
Enters numbers in BOLD, Results in RED
Schematic

simply supported
Plate dimensions and properties Values ProE Simulation
Length a (mm) 300 300
Width, b (mm) 200 200
Thickness, t (mm) 1.5 1.5
Modulus of elasticity, E (N/mm^2) 200000 200000
Poisson ratio, v 0.29 0.29
Total area 60000
a/b, aob 1.50
Loading
Uniform loading pressure over entire plate, q (N/mm^2) 0.00017 0.00017
Total load applied to the plate, W (N) 10
Uniform over small concentric circle of ro, qo (N/mm^2) 10 10
Load application radius, ro (mm) 2 2
Outer radius used in calculation, ro_prime (mm) 2
Total load applied to center of plate, Wo (N) 126
Simply supported outer boundary:
Distributed load:
Center displacement, dc (mm) -0.033 -0.032
Bending stress at center (N/mm^2) 1
Reaction load at center of long side (N/mm) 0
Centrally applied concentrated load:
Center displacement, fdc (mm) -1.248 -1.247
Bending stress at center (N/mm^2) 189

From Roark & Young, Formulas for Stress and Strain, 5th eddition, page 386
Interpolated parameters from curves:
Uniform loading
salpha 0.0840938
sbeta 0.4869375
sgamma 0.4836563
Central loading
falpha 0.1676125
fbeta 0.8373188

Uniform load over entire plate


a/b 1 1.2 1.4 1.6 1.8 2 3 4
beta 0.2874 0.3762 0.453 0.5172 0.5688 0.6102 0.7134 0.741
alpha 0.0444 0.0616 0.077 0.0906 0.1017 0.111 0.1335 0.14
gamma 0.42 0.455 0.478 0.491 0.499 0.503 0.505 0.502

Simply supported rectangular plate with uniform loading


0.8

0.7 f(x) = − 0.00336683549 x⁴ + 0.05698777324 x³ − 0.3669440277 x² + 1.0756433252 x − 0.47614668044

0.6
beta
0.5
f(x) = − 0.0038835418 x⁴ + 0.05362587115 x³ − 0.26775919054 x² + 0.56966388636 x + 0.07048258478
Polynomial (beta)
0.4 alpha
Polynomial (alpha)
0.3 gamma
Polynomial (gamma)
0.2

0.1 f(x) = − 0.00045017532 x⁴ + 0.00864897934 x³ − 0.06203348659 x² + 0.19878242669 x − 0.10109846986

0
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
a/b

Central load over small radius


a/b 1 1.2 1.4 1.6 1.8 2 2.5
beta 0.435 0.65 0.789 0.875 0.927 0.958 1
alpha 0.1267 0.1478 0.1621 0.1715 0.1777 0.1805 0.1851

Simply supported rectangular plate with central loading


12

10

6
Simply supported rectangular plate with central loading
12

10

0
1 1.2 1.4 1.6 1.8 2 2.2 2.4

a/b
5
0.7476
0.1417
0.501

ng

2 x − 0.47614668044

beta
6 x + 0.07048258478
Polynomial (beta)
alpha
Polynomial (alpha)
gamma
Polynomial (gamma)

9 x − 0.10109846986
2 2.4
Displacement along the length for uniform loading

Displacement along the length for central loading

You might also like