Recent Advances in Wearable Antenna Technologies A Review

Progress In Electromagnetics Research B, Vol.
89, 1–27, 2020
Recent Advances in Wearable Antenna Technologies: A Review
Sarmad N. Mahmood1, * , Asnor J. Ishak1 , Tale Saeidi2 , Hussein Alsariera3 ,

Sameer Alani4 , Alyani Ismail5 , and AzuraChe Soh1
Abstract—Wearable antennas have received a great deal of popularity in recent years owing to their
enticing characteristics and opportunities to realize lightweight, compact, low-cost, and versatile wireless
communications and environments. These antennas must be conformal, and they must be built using
lightweight materials and constructed in a low-profile configuration when mounted on various areas of
the human body. These antennas ought to be able to function close to the human body with limited
deterioration. These criteria render the layout of wearable antennas demanding, particularly when
considering factors such as investigating the usability of textile substrates, high conductive materials
during fabrication processes, and the effect of body binding scenarios on the performance of the design.
Although there are minor differences in magnitude based on the implementations, several of these
problems occur in the body-worn deployment sense. This study addresses the numerous problems and
obstacles in the production of wearable antennas, their variety of materials, and the techniques of
manufacturing alongside with bending scheme. This is accompanied by a summary of creative features
and their respective approaches to address these problems recently raised by work in this area by the
science community.
1. INTRODUCTION
Wearable devices are set to increase to 578 million in 2019, which reflects a fivefold improvement
compared to 2014 apps [1]. Wearable devices are the ones where a human can wear and have the potential
to communicate explicitly to each other or via integrated cellular communication. They connect with
other devices through their integrated wireless modules, which interface with other elements such as
batteries, sensors, and antenna. Antennas are one of the essential aspects of wearable gadgets as
they lead to a portable link for the overall effectiveness of the devices. Wearable devices have various
applications in our everyday lives. These are not restricted to wristwatches, exercise shoes, virtual reality
glasses, and include other medical devices as well [2, 3]. Across the healthcare industry, wearable tools
are used to track vital health problems of the patients. These wearable devices have a glucose control
device for measuring the insulin level of a patient, capsule endoscopy for testing the inner digestive tract,
handheld sensor machine, and heart rate tracking thermometer, blood pressure, and body temperature.
Wearable tools may also be used with evacuation and disaster management services, including boots,
socks, raincoats, and helmets [4]. While developing portable antennas for use as part of the outfit of the
wearer, many things need to be addressed. Wearable devices ought to be unobtrusive, versatile, and work
close to the human body with minimal deterioration [5, 6]. Wearable antennas are often tricky in terms
of production, the availability of inventory on different body sites, the impact of the host body, and the
Received 18 July 2020, Accepted 8 September 2020, Scheduled 25 September 2020
* Corresponding author: Sarmad Nozad Mahmood ([email protected]).
1 Department of Electrical and Electronic Engineering, Faculty of Engineering, Universiti Putra Malaysia, Serdang 43400, Malaysia.
2 Electrical and Electronic Engineering Department of UniversitiTeknologi PETRONAS, 32610 Bandar Seri Iskandar, Perak, Malaysia.
3 Faculty of Electronic and Computer Engineering (FKeKK), UniversitiTeknikal Malaysia Melaka, Melaka 76100, Malaysia. 4 Faculty
of Information and Communication Technology, UniversitiTeknikal Malaysia Melaka, Melaka 76100, Malaysia. 5 Department of
Computer and Communication Systems Engineering, Faculty of Engineering, Universiti Putra Malaysia, Serdang 43400, Malaysia.
2 Mahmood et al.
loss of efficiency due to structural deformation are problems that need to be addressed throughout the
design phase [7]. Wearable antennas have to be upgraded with multiple main characteristics. Preferably,
wearable antennas should be designed and tested to facilitate operation at lower frequencies in order to
be circularly polarized and support satellite location sensing when being used outdoors [8, 9]. The main
advantage of such wearable devices is that wireless connectivity from or to the body through conformal
and wearable antennas must be enabled.
Wearable antennas play a crucial role in centric on-body wireless communications and attract
substantial interest in the researches. Since wearable antennas work close to the human body, the loading
impact attributable to the loss aspect of body tissues combined with their strong dielectric constants and
conductivity renders it challenging to construct a high radiation output antenna [10–12]. It is further
exacerbated by the need and demands that these antennas be lightweight low cost, maintenance-free, and
do not need setup. It is worth mentioning that one of the main research interests of wearable antennas
for Wireless Body Area Network (WBAN) applications [13] is the patch antenna as a consequence of
the wide ground plane used in its construction, owing to its fairly high directionality. In addition to the
directivity, microstrip patch antennas give enormous benefits for on-body wearable devices. The three
primary ones being: simplicity of design, cost-effectiveness, and the relative separation provided by the
ground plane between the radiating component and the surface, which results in a substantial reduction
in the energy consumed by the skin [14]. Patch antennas, though, appear to be small in bandwidth and
might need to be fairly wide if they are to be adequate to body interference [15–18].
Wearable antennas are those antennas that work within the human body, such that the human
body consumes some of the radiated energy. Thus, the antenna output reduces [19–22]. Wearable
antennas are also challenging in terms of textile-based antenna performance concerning (dielectric
constant (εr), loss tangent (δ), and thickness (h)) of the substrate materials, the high conductivity
of the materials (σ), and the antenna in bending scenarios. It is worth mentioning that the properties
of the employed materials control the behavior of the antenna such that the bandwidth and efficiency
of a planar microstrip antenna are primarily determined by the dielectric constant and thickness of the
substratum [23, 24]. Metamaterials are groups of several individual components made from traditional
microscopic materials like metals or plastics, but the products are typically organized in repeated
patterns [25]. Furthermore, Conductive Metamaterials increase total synchronization and decrease
radiation from tiny antennas [26], minimize the specific absorption ratio (SAR) in the head [27], and
monitor electromagnetic near-fields across the antenna, which can be used to minimize the absorbed
strength in human body tissues. Note that this article is outlined as follows: Section 1 provides a
general introduction to wearable antenna designs, performances, and applications. Section 2 investigated
the performance of textile wearable antennas with respect to their size, substrates, and frequency
bands [29, 37, 42–44, 46, 57, 59, 60]. Furthermore, the bending scenarios of antennas in several radiuses
and the impact of bending on the efficiency were addressed in Section 3 [59, 67, 70, 71, 73, 79, 85, 91–93].
On the other hand, Section 4 exposed the high conductive substrate materials and discussed their effect
on the design and fabrication of different wearable antennas [111, 115–119, 124, 125, 132]. Moreover, the
entire review was summarized in Section 4. Finally, the conclusion of the whole article is presented in
Section 5.
2. TEXTILE WEARABLE ANTENNAS
An intelligent fabric is any textile that offers the physical state of the wearer by means of the attached
electronic system. They are also classified as smart garments, e-textiles, smart materials, garment
tracking, etc.. The e-textile invention went back to the 20th century and started largely as a consequence
of the production of a conductive polymer by [28] in 1977, for which he won the Nobel Prize thirty-three
years ago. Inside smart clothing, textile antenna plays a significant role in delivering wireless features
such as detecting, identifying, processing, controlling, etc. without giving the user any pain [29]. With
the advancement of fashion technologies, there has recently been a growing need for a smart wearable
antenna. In addition to preserving the original role of heat protection and beautification, these textiles
are often crucial to the advancement of knowledge science, materials science and other associated fusion
technologies. Work into wearable device technologies has gained increasing attention [30–36].
Telecommunications are an integral aspect of daily life and enable citizens to exchange knowledge
Progress In Electromagnetics Research B, Vol. 89, 2020 3
through computers and other electronic devices. To this end, the demand for a wireless communication
system is increasing. In [37], Mohan et al. used two separate substrates to conduct a report on the
output characteristics of the UWB antenna based on the Rectangular patch antenna design. Compact
UWB antennas were built for two substrates in the proposed research, and attention was given to
a low-cost flame-resistant FR4 and the jeans substrates. Since both antenna designs had fulfilled
the UWB antenna requirements, it was observed that the antenna built using FR4 reached reflection
coefficient at frequency ranges between (3.8–10.9) GHz, while the jeans based antenna design displayed
a reflection coefficient at frequency ranges (2.6–9.8) GHz with omnidirectional radiation pattern. Due
to the lightweight existence of textile content, it could be more beneficial to build antenna using jeans
fabrics, because it can be easily inserted into clothes. However, the performance of the antenna, including
omnidirectional radiation patterns, gain, size reduction, and textile antenna miniaturization needs to
be optimized. The results derived from the bandwidth characteristics revealed that the proposed UWB
antenna design can operate well in excessive wideband range and was considered to be appropriate
for use in UWB applications. Analytically, the quality and suitability of cloth fabrics must be further
studied, as well as the firmness and durability of cloth being a significant consideration in the final
selection of products alongside SAR value reduction which can be considered as the main objective in
most of the antenna designs.
Owing to their wide possible applications such as health control, sport, navigation, and military,
WBAN systems were gaining more publicity in past years [38, 39]. Wearable antennas are important
research works in both academia and business, being one of the key components of the WBAN network
for wireless contact with other gadgets on or off the human body [40, 41]. Accordingly, Turkmen et al. [42]
introduced a lightweight and adaptable textile antenna design and analysis for WBAN systems. The
antenna was constructed from a textile jeans substrate with desirable characteristics such as lightweight
low dielectric properties alongside copper tape used for the radiator patch and ground plane of the
antenna, as shown in Figure 1. According to the results, the proposed antenna realized optimum
reflection coefficients (S11 ) and radiation patterns under different antenna bending conditions with
better reflection results in Y -axis bending. Under this act, the antenna can be a suitable choice for
WBAN applications. The antenna efficiency parameters (return loss and radiation pattern parameters)
(a) (b)
(c)
(d) (e)
Figure 1. Proposed antenna: (a) Front, (b) back, (c) bottom, (d) bending X-axis, (e) Y -axis [42].
4 Mahmood et al.
were tested for planar and bending conditions in free space. For planar configuration, the antenna
displayed larger operating band between 2.2 GHz and 17 GHz, spanning the frequency spectrum UWB
(3.1–10.6 GHz). For bending configuration, the active frequency bandwidth of the antenna is reduced
by about (1–1.5) GHz from the upper frequency area due to the increasing in antenna bend range. For
planar and bending configuration, depending on the planar condition there is a variation in the antenna
twist states in all twisted directions.This adjustment doesn’t have a significant impact on the antenna’s
radiation efficiency. Nevertheless, the radiation pattern with the bending scenario around Y -axis is
more stable than the bending around X-axis.
In the same trend, Wang and Li [43] introduced a design of a flexible double band woven antenna
with miniaturized construction. The proposed antenna was constructed at (2.45) GHz and (5.8) GHz
ISM band utilizing denim as antenna substrate and copper tape as a radiation part (see Figure 2).
Using denim, a dielectric constant of (1.54) was realized based on a simple method with return loss.
The study revealed that all facets of antenna efficiency were not significantly impaired when the antenna
was positioned close to the human body. Additionally, the robust functionality of the antenna indicates
its suitability for portable wearable devices. Furthermore, the proposed antenna realized maximum gain
value specified by (6.34 and 4.7) dB at (2.45 and 5.8) GHz respectively. However, there is a slight shift
in the resonant frequency and variance bandwidth with the antenna being put in free space relative to
the on-body state, and yet the frequency spectrum still appropriate at 2.45 GHz and 5.8 GHz for (ISM).
(a)
(b)
Figure 2. (a) Structure parameters of proposed textile antenna. (b) Prototype of denim antenna [43].
Moreover, Li and Li [44] exhibited a unique textile woven antenna operated with ISM band. The
designed wearable antenna had a limited impact on the human body and conveniently manufactured on
textiles (see Figure 3). The conceptual portable textile antenna was built for futuristic wireless networks
to work on (2.45) GHz (5.8) GHz commercial, science, and medical (ISM) frequencies. Furthermore, the
proposed antenna is classified as a compact size with an omnidirectional radiation pattern. It was
supposed to be a perfect choice for human body based wearable antennas due to its extraordinary
operating frequency, scale, and incorporation into the clothing property.Noteworthy, the two center-
resonant frequencies for on-body states were significantly changed towards low frequency and affected
the result slightly compared with the antenna in free space situation.
A smart garment is any apparel that supplies the physical state of the wearer via the connected
mobile device; it is often referred to as smart clothing, e-textiles, smart fabric, display clothing,
etc. Owing to the usage of readily accessible materials for its development, Jayabharathy and
Shanmuganantham [29] introduced an essential structural and cost-effective antenna design (see
(a) (b)
Figure 3. (a) Wearable antenna configuration. (b) Photo of the fabricated antenna [44].
Figure 4. Front and back view of the antenna [29].
Figure 4). The proposed module was extended to cover the larger frequency range, which could widely
support short-range tracking, missile guidance, and other radar applications. The proposed antenna
obtained reasonable reflection coefficient values and decent gain; accordingly, it can be used in different
health monitoring fields. Moreover, it can be mentioned that the antenna based cotton and leather
substrates provided limited results comparing with jeans, and the proposed antenna realized narrow
gain ranges of (2.2–3.2) dB.
Furthermore, smart clothes have the potential to track the bio-signal of an individual and transmit
this knowledge in order to provide details about the wellbeing of a person in real-time. In recent years,
portable antennas have gained interest because they could be built into the clothes [45]. A new wearable
UWB semi-circular slot antenna was constructed by Amit et al. [46] utilizing (flannel, cotton, and jean)
based textile materials. As a comparison, it was observed that the reflection coefficient with phantom
based any fabric is higher than (10) dB, which satisfied the requirements of the design. However,
when considering FR-4, the corresponding antenna impedance and bandwidth are low. Flannel offers
higher efficiency than other materials, as the pattern was homogeneously relative to cotton and jeans.
Furthermore, the proposed textile antenna covered acceptable frequency range rendering the antenna
to be well suited for wearable devices relevant to smart clothing. Furthermore, the results reveal a
6 Mahmood et al.
mismatching between the simulated and fabricated tests by (29 and 22) dB impedance matching and
return loss respectively. When considering FR-4, the antenna impedance matching and the bandwidth
are low. Whereas flannel does even higher than other materials, as the structure is homogeneous in
comparison to jeans and cotton.
For diagnostic uses, microwave imaging was commonly used to image the interior of human bodies
and to identify pathogens as they already grow for their early stages [47, 48]. These diseases might
involve strokes of the brain, breast cancers, bone fractures, and damage to the sub-skin [49–56]. In light
of this, Lin et al. [57] proposed novel low-profile ultra-wideband full-textile antenna architecture for
portable medical imaging systems in the microwave. The antenna offered an easy-to-fabricate monopole
frame made of lightweight polyester fabrics and conductive copper taffeta, resulting in a small and
versatile framework for functional applications that conforms to the curved nature of human bodies.
The calculated tests revealed that the antenna achieved an UWB operational bandwidth of 109 percent,
better omnidirectional radiation, and appropriate gain of (2.9) dBi. The antenna also maintained its
output in the presence of tissue-mimicking phantoms during bending or operating (see Figure 5). In
contrast, on-phantom calculations indicate that there was little impact on the working bandwidth and
the perceived gain of the antenna as it operates in the vicinity of human bodies. The time-domain return
loss of the antenna differed dramatically with the scale of the implemented fragment, which adapted the
functionality of the antenna with microwave medical imaging for such usage scenarios. Noteworthy, this
paper did not introduce or analyze many sophisticated post-processing algorithms to recreate images
and increase their accuracy based on the captured microwave signals. Besides, the strategy to improve
the forward radiation of the antenna in a low-profile way was utilizing the electromagnetic bandgap or
faulty ground structure may be a viable solution and deserved to be unveiled.
(a) (b)
(c)
(d)
Figure 5. (a) Monopole antenna. (b) Cut two triangles — bottom. (c) Cut parallel — top. (d) SMA
prototype [57].
The use of electro-textiles and smart clothes in connectivity, culture, health, and safety involves
the installation of several electronic tools directly onto textile substrates to increase the security and
efficiency of the consumers [58]. In view of this, an innovative Ultra-wideband textile (UWB) antenna
was proposed by El El Gharbi et al. for portable applications in [59]. The proposed antenna was
constructed and introduced with desirable characteristics such as a robust full embroidered topology
and low dielectric loss on a felt textile substrate with full antenna dimensions (30 × 30 × 0.7) mm (see
Figure 6). This small size of UWB antenna output ranges from (3.1–11.3) GHz, indicating a fractional
bandwidth of 114 percent, where the performance approaches 60 percent and the gain obtained hits
(4) dB. However, some influences such as the SMA connections, soldering defects, and the production
cycle of embroidery adaptation that were not accounted for in models caused few minor differences in
the measured performance.
Furthermore, Di Natale and Di Giampaolo [60] presented and addressed a UWB flexible all-textile
antenna that can be reconfigured between a monopole and a microstrip-like antenna (see Figure 7).
(a) (b)
(c)
Figure 6. Geometry of proposed antenna: (a) Front view, (b) back view and (c) bottom view [59].
(a)
(b) (c)
Figure 7. (a) Side view of the antenna. (b) Monopole configuration. (c) Microstrip-like
configuration [60].
The antenna is centered on a circular radiating disk that functions as a monopole when orthogonally
positioned on a ground plane, and as a microstrip patch when situated parallel to an adjusted ground
line. The numerical analysis demonstrates that both topologies have a sufficient UWB functionality
with FCC-compliant bandwidth and a reasonable network fidelity factor that enables the antenna to
be used as an air interface for wearable sensors and short-range communication tools. The variance of
the average gain oscillates between (2 and 6) dB in the case of the monopole, and between (2 and 8) dB
in the case of microstrip topologies. Noteworthy, the results indicate that the antenna is unresponsive
to the body owing to the ground surface and that the characteristics do not alter dramatically with or
without the body in terms of the reflection coefficient and the radiation pattern.
The overall evaluations among the works given in the aforementioned analysis in Section 2 were
summarized as exposed in Table 1.
8 Mahmood et al.
Table 1. Overview on textile wearable antennas.
Size Frequency h Eff
Ref. Substrate εr Application
(mm) Band (GHz) (mm) (%)
1.6 FR4 4.4
[37] — 3.1–10.6 — UWB devices
1 Jeans 1.67
[42] 45 × 60 2.2–17 1 Jeans 1.68 WBAN
Wearable
[43] 46 × 16 2.45 and 5.8 0.05 Denim 1.54 —
and ISM
Wearable
[44] 42 × 13 2.45 and 5.8 25 Denim 1.54 —
devices
Health
[29] 28 × 43 3–8 9–13 1.2 Jean 1.7 —
monitoring
Jeans
3–10 Health
[46] 33 × 35 1 Flannel 1.7 72
4–9 monitoring
Cotton
Polyester 56.48 Microwave
[57] 45 × 40 1.198–4.055 0.08 2.193
Fabric 70.96 medical imaging
Wearable
[59] 30 × 30 3.1–11.3 0.7 Felt 1.2 < 60
devices
2.61–10.1
[60] 90 × 90 0.6 Denim 1.43 — WBAN
2.73–10.1
3. BENDING SCENARIOS IN WEARABLE ANTENNAS
For mounting on non-conform surfaces and using rigid substrates, many wideband, extensive band
(EWB), and UWB notched antennas have been published [61–66]. When using the antennas around
angled surfaces, they experience bending or flexing, which can alter the antennas’ reflective properties.
Since the antennas are built on flexible substrates, in various bending situations, the constructed
antennas are tested concerning the bending in order to verify the performance of the antennas.
Throughout the activity, textile antennas are expected to be bent or otherwise conformed to a particular
surface, and so experiments under various bending circumstances are important to explore differences
in bending-dependent features. The antennas are either mounted or twisted over a ring, which could
be a typical arm or chest form pattern [59, 67].
A WBAN consists of body-located wireless nodes that can communicate with each other and/or
with an external base station using an effective antenna. Multiple antennas used by body region
networks are the monopole Microstrip Patch Antenna (MPA) [68] and the dipole microstrip patch
antenna [69]. Accordingly, Bala et al. [70] investigated the advantages of graphene in constructing a
curved patch-based antenna for flexible WBAN applications. The overall dimension of graphene curved
patch antenna was (35 × 35) mm (see Figure 8), which efficiently obtained (−25.05 and −25.17) dB
reflection coefficients, (10.5 and 2.8) dB maximum gain, (1.118 and 1.12) voltage standing wave ratio
(VSWR) and (79.09 and 74.86)% radiation efficiency at resonating frequency of (2.4 and 3.94) GHz
respectively. Furthermore, the results proved that the proposed antenna could act perfectly in operating
frequency range (1–4.88) GHz alongside with acceptable SAR value. Due to the functionalization of the
graphene, the basic curved based square patch antenna achieved wideband activity and is also ideal
for UWB WBAN biotelemetry applications.The curved graphene patch antenna was located crosswise
along the length of the body resulting in small resonant frequency differences, while it is found that
any change in patch width results in the resonant frequency shifting to a higher band. Due to extreme
absorption defects in the GHz range, the radiation performance of the planar graphene patch antenna
(a) (b)
Figure 8. (a) Graphene-based curved patch antenna model. (b) Dimensional view [70].
is degraded and may therefore be balanced by the usage of silicon substrate content with a higher
dielectric constant.
Furthermore, Liu et al. [71] studied the impact of the bending on the performance of the antenna
by demonstrating a design of a flexible Yagi-Uda antenna based on polymer substrates for WBAN
applications. The overall antenna size is exposed in Figure 9(a), where the whole module was formalized
to satisfy the ISM frequency range specified by (2.45) GHz. The effect of the bending conditions on the
x and y axes of the proposed antenna exhibited that the input matching got awful with an increase in
the bending degree of the design. The reflection coefficient of the proposed antenna was measured in
the range of (10 MHz–43.5 GHz) and reached an impedance bandwidth in the range of (2.4–2.5) GHz
considering that the return loss was less than (−10) dB (see Figure 9(c)). It should be reported that
the average radiation path at the H-plane of the antenna is deviated by bending across y plane (see
Figure 9(b)). Nevertheless, the corresponding antenna output remained fairly stable under bending
circumstances. Moreover, it can be revealed that due to the feeding cable impact induced by the tiny
ground plane a slight difference between simulation and calculation was conspicuous.
(a) (b) (c)
Figure 9. (a) Proposed antenna geometry. (b) Antenna bending. (c) S11 response [71].
The increasing growth of portable low-power systems has intensified the need for WBAN
Deployment solutions. The antennas can be used by emergency personnel such as paramedics or
police officers in devices tracking body tension during physical operation, measuring heart rate and
blood pressure [10, 72]. In accordance with that, Ferreira et al. [73] discussed the impact of bending on
the efficiency of the 2.4 GHz rectangular microstrip textile patch antenna for WBAN. The conductive
10 Mahmood et al.
component of the antenna was a combination of copper and nickel, mixed as a substrate of polyester
fiber and denim. The results showed that bending curvatures have an important effect on the cost
and cumulative distribution of radiation. Noteworthy that the overall antenna structure was tested in
three generic locations: the chest, arm, and wrist. Relative to a flat antenna case, the wrist-equivalent
curvature reduces the average gain by around (2–4) dB. The front-to-back radiation density of the
antenna declines with a rise in the bending curvature, which can be a favorable property for WBAN
instances. The bandwidth remained nearly the same in all calculated situations. The resonant frequency,
on the other side, had specific actions based on how the antenna is bent along its width or duration.
Once the antenna was subjected to a bending curvature on its diameter, a downhill frequency offset
was detected, and an uphill frequency offset was investigated for bending along the length axis of the
antenna.Therefore, when developing textile-patch antennas for WBAN applications, the antenna output
may be greatly restricted by the resonant frequency offset with respect to antenna curvature angles.
The key emphasis on antenna architecture is the lightweight wearable high-performance antenna
creation for on the body use [74–78]. Meanwhile, Isa et al. [79] studied the performance of a dual-band
textile-based circular patch antenna in different bending scenarios. For this analysis, three bending
cases were studied depending on several bending radiuses. The circular microstrip patch with a size
of (70 × 70) mm was developed to be suitable for tiny human limbs (arms, legs) and relatively some
larger sides in the human body (see Figure 10). The results indicated that bending along the E-plane
had a dominant impact on the performance of the antenna. Based on the proposed case studies, the
bent antenna caused variation in the period of resonance owing to the modest influence of the bending
on the resonance frequency. The reflection coefficient of the antenna was influenced by bending in the
narrower radius due to the reduction in the resonance range of the antenna. Furthermore, the impact
on bandwidth was roughly marginal, assuming that no resonance had been impaired. Briefly, it can be
inferred that the implications are negligible. Hence it had been demonstrated that the expected textile
antenna can operate reasonably under bending constraints. Bearing in mind that the proposed dual-
band antenna operates in both (2.4) GHz and (5.2) GHz respectively, alongside with wider bandwidth is
achieved across (1.95–5.79) GHz. Worthwhile that the return loss declines marginally for all situations,
particularly at high band frequency in comparison with the flat antenna output resulting from the
maximal bending which is considered awful for the outer ring of the patch.
The flexible antennas are a number of antennas used for a range of uses such as tracking, telephone
control, sports control, (WBANs), Wireless Sensor Networks (WSNs), and Wireless Personal Area
Networks (WPANs) [80, 81]. Several antennas were implemented in the last couple of years relating to
(a)
(b) (c)
Figure 10. (a) Circular monopole patch antenna. (b) Bending positions. (c) Experimental setup [79].
(a) (b)
Figure 11. Proposed antenna geometry. (a) Polyamide. (b) Teslin paper [67].
flexible/wearable communications systems [38, 82–84]. In light of this, Mohandoss et al. [67] introduced
a compact, low-profile and durable planar monopole antennas aimed for UWB and Body Centric
communication technology (BCWC) was constructed and tested for their efficiency across conformal
surfaces. In this work, two microstrip based lightweight antennas were designed using polyamide and
Teslin substrates. The antennas realized several features summarized as follows: overall dimensions of
the proposed antennas specified by (50 × 40 × 0.8) mm and (50 × 40 × 0.712) as depicted in Figure 11,
operating frequency of (1.8–13.3) GHz and (1.4–13.4) GHz, maximum gain of (5.53) and (4.4) dBi,
better radiation patterns and return loss (S11 ) of (11.5) GHz and (12) GHz for polyamide and Teslin,
respectively.
The performance of the antennas was evaluated based on flexible scenarios such that bending across
the length, widths, radius, and angles of the antenna (see Figure 12). Therefore, time-domain research
was conducted in free space and with pulse excitation in different bent situations to verify the antennas
for UWB applications. The properties of the propagation coefficient (S21 ) and the community latency
for various bending situations were calculated and the fidelity parameter for both scenarios was greater
than 0.82 which classify these antennas to be a good candidate for UWB-BCWC, high-speed data
(a) (b) (c) (d)
(e) (f) (g) (h)
Figure 12. Inward bending. (a) X-bend, (b) Y-bend, (c) X-bend with +45 deg and (d) Y-bend with
+45 deg, (e) X-bend, (f) Y-bend, (g) X-bend with +45 deg and (h) Y-bend with +45 deg [67].
12 Mahmood et al.
connectivity of wireless personal area networks and flexible wideband pulse frameworks. However, it is
found that there exists frequency change between simulated and measured (S11 ) for Teslin antenna could
be attributed to adhesive employed by the Teslin papers to render it a single substratum in comparison
to the polyamide antenna.
In [85], Mersani et al. introduced a compact monopole antenna to diagnose skin cancer in a person
afflicted by xeroderma pigmentosum diseases for use in radiography. The proposed antenna reacted
successfully with the specified criteria and showed UWB behavior. The overall dimensions of the
proposed antenna specified by (36 × 48 × 6.12) mm realized impedance bandwidth (8.2–13) GHz and
maximum gain of (7.04) dBi. The antennas are built to be mounted under the body; thus, they would
be subjected to curvature restrictions. Hereby, the return loss values descended awfully than the values
in the source antenna in the bending conditions (see Figure 13). Such results proved the effectiveness
of antenna sensitivity in and out of the curved environment. On the other hand, for the antenna with
AMC the rear radiation rates are lower than the independent antenna, and also the same actions were
noticed when putting the AMC antenna on the body. Besides, owing to interference and also energy
absorption in the body, the gain and output of the AMC antenna mounted on the body are reduced as
in comparison to the AMC antenna mounted in free space.
(a)
(b)
Figure 13. (a) Geometry of the patch antenna. (b) Bending antenna [85].
Several flexible antennas were made on numerous flexible substrates such as textile [86, 87],
paper [88], and thin-film [89, 90]. Accordingly, a star patch Kapton Polyimide Film based antenna
was designed by Seman et al. [91], which was able to function at (2.45) GHz. The size of the antenna
was specified by (75×50) mm2 and tested in different bending scenarios (see Figure 14) knowing that the
results had proven that the performance of the antenna is not compromised. Furthermore, the results
showed that the antenna grasped an optimized bandwidth of 24.9% covered by the stated (2.45) GHz
frequency and lowest return loss in the flat state. Additionally, the bending scenarios were diameter-
based examination depending on specific diameters as shown in Figure 14. Though, the antenna had
to be installed into a transceiver device and validated to evaluate the real output in the specific indoor
and outdoor environment.
It is worth mentioning that the consistency of the efficiency has been observed in which the resonant
frequency change is less than 2% when the system is bent on a curved surface with a 90 mm radius.
Hereby, the proposed antenna can be a suitable candidate for wearable devices. Similarly, Gupta et
al. [92] studied and evaluated the efficiency of conformal UWB portable antenna in the domination of
different bending radii. The proposed antenna was constructed on RT Duroid flexible substrate with
(a) (b)
(c)
Figure 14. (a) Star patch antenna. (b) Bending D = 120 mm. (c) S11 under bending scenarios [91].
overall dimensions of (35×31) mm2 and studied depending on (25 and 50) mm bending radius applied on
the arm of a 5 years old healthy child and a 35 years old healthy adult respectively. With respect to the
reflection coefficient of the conformal UWB antenna, an identical response was achieved for the various
curvature radii, knowing that the realized reflection coefficients were less than (10) dB in both bending
radius of UWB wearable antenna and operating frequency range of (3–10) GHz. As a result, due to
the durability, flexibility, and the thickness of the proposed antenna, the design can be classified as an
optimum choice for UWB wearable applications. However, the calculated findings could be attributed
to a slight variance in the cardboard in which the antenna has been covered for compatibility evaluation.
Moreover, the cardboard itself can have some dielectric properties and would undoubtedly influence the
operating frequency.
Furthermore, Yin et al. [93] proposed and illustrated a wearable antenna with L-slot AMC
configuration for ISM fields (see Figure 15). The radiation of the antenna back lobe was effectively
minimized by introducing an AMC layer, which increases antenna efficiency. The front to the back
value of the antenna is greater than 20 dB in ISM medical range, reaching a gain of 7.47 dBi. The SAR
value is smaller than 0.15 W/kg, which is much smaller than the universal implementation level, showing
that it does not affect human safety and still has good efficiency even under different bending scenarios.
Due to these characteristics, the proposed antenna can be a suitable option for wearable devices such
as medical tracking and medical sensing in WBAN. Nevertheless, there are certain variations in the
tests obtained that can arise from adjusting the gap between the upper antenna and the AMC reflector
(a) (b) (c)
Figure 15. (a) Proposed wearable antenna structure. (b) Top view of the fabricated antenna. (c) The
integrated antenna with different bending degrees [93].
14 Mahmood et al.
during the study, creating an inexplicable delay, and welding the antenna feeding port and field test
area can even influence the actual antenna verification.
Owing to the versatility of the textile material antennas, they are readily bendable to conform to
the structure of the human body and provide consumer convenience; even under bending circumstances,
the antenna can retain its optimum efficiency. Hence, under specific bending conditions, lightweight
wearable antenna efficiency parameters should be evaluated [59, 94]. As presented before, El Gharbi et
al. [59] presented an Ultra-wideband textile (UWB) antenna designed for wearable applications. Besides,
El Gharbi discussed the effect of bending on the performance of the antenna. For this experimental
analysis, as seen in Figure 16, the proposed textile UWB antenna was used in two separate concave
and convex bending conditions. Furthermore, each location was determined by taking into account the
normal bending radius between (30 and 45) mm in the human body. The comparison results showed
that the availability of the smallest radius and firmest bending result in wide detuning. Based on
bending scenarios, tiny bandwidth change in percentage between the measured and simulation results
was recorded and justified by several potential reasons: the flexibility of the embroidery production
system, the influence of humidity and temperature on the successful dielectric permittivity of the felt,
the non-uniformity sample thickness (rugosity).
(a) (b)
Figure 16. Measurement environment of textile bending UWB antenna. (a) Concave. (b) Convex [59].
Furthermore, the overall evaluations among the works given in the aforementioned study regarding
Section 3 were summarized as exposed in Table 2.
4. WEARABLE ANTENNA BASED CONDUCTIVE MATERIALS
The interest in wireless wearable communication technologies had been increasing drastically for
recent years. The aim is to meet the wearable specifications of the device, such as durability,
compactness, robustness against harsh climate, low-cost, and ease of manufacturing. Recently, many
attempts have been documented utilizing different exotic materials from cloth, textiles, embroidered
fabrics, liquid metal, polymers, to Nano-materials [95–104]. The usage of polymers, especially the
polydimethylsiloxane (PDMS) type, has been labeled as one of the most important methods, owing
to its peculiar features such as exceptional strength, water resistance, heat, and mechanical resilience,
which are necessary for convenient wearing and extended utilization [105, 106]. In the field of developing
wearable antennas, there has been growing demand and production, which are convenient and can be
easily incorporated into the incorporated microwave device. The modern microstrip antennas have the
intrinsic drawback of being static, which also prevents their implementation into a fully portable device.
On-body Antennas can be created from textiles [30, 107–110] and connected to the body or clothes
or can be worn as an antenna button [80]. In [111], the layout, production, and characterization of
electro-conductive textile fabric (ECGT) based rectangular textile wearable antenna (RTA) was stated
by Gangopadhyay et al. The design comprises conductive cotton and copper filament yarns that were
twisted together to create an integrated fabric. It is worth mentioning that the established ECGT had
Table 2. Overview on bending scenarios in wearable antennas.
Rad. Eff.
Ref. Substrate Radius (mm) BW SAR (W/kg) Application
(%)
[70] Silicon 30 79.09, 74.86 3.88 GHz 0.000148 Medical
20, 30, 40, 50,
[71] Polyimide — 360 MHz — WBAN
60, 70, 180, 360
[73] Denim 28.5, 42.5 — 140 MHz — ISM
[79] Jeans 33.5, 47.5, 58.5 — 3.84 GHz — WLAN
Polyamide 87, 92, 96 11.5 GHz UWB and
[67] 8, 15, 30, 80 —
Teslin-paper 82, 86, 89 12 GHz (BCWC)
Medical
[85] Felt 10, 15, 20 64 4 GHz 0.102
imaging
Polyimide Diameter 24.9% Wearable
[91] — —
film = 70, 90, 120 ≈ 400 MHz devices
Off-body
[92] RT Duroid 25, 50 60 7.1 GHz —
wearable
[93] Polyimide 50, 100, 150 — 2.45 0.15 ISM
Wearable
[59] Felt 30, 45 > 60 8.2 GHz —
devices
realized a surface resistivity of (2.97) Ω/square (see Figure 17). In summary, the proposed antenna
obtained percentage bandwidth around (6.7 and 10)%. The overall gain was obtained as (5.5 and
7.6) dBi at (2.021 and 2.054) GHz, respectively, with antenna efficiency around (61.42)%. It has to be
mentioned that the behavior of the antenna needed further optimization, especially to improve the poor
efficiency of the module.
(a) (b) (c)
Figure 17. (a) Copper filament. (b) Geometry of ECGT-RTA. (c) Comparison of S11 result [111].
A versatile antenna is a crucial component of the new wireless wearable gadgets. The durability
criterion exists because the majority of wearable devices are subjected to regular physical deformation in
their operating setting. The flexible antenna must deal with the conditions of the body while retaining
the comfort of the individual. In recent years, this necessity has sparked a rapid advent of utilizing
innovative materials for producing lightweight wearable antennas [99, 102, 112–114]. In view of this,
Simorangkir et al. [115] successfully reported how PDMS integrated conductive fabric materials can be
employed to design adaptable, robust, frequency re-composition and wearable antenna. The conductive
side of the PDMS substrate-based antenna design was realized using NCS95R-CR, a nylon ripstop fabric
covered by nickel, copper, silver and a water-resistant layer is presented in Figure 18.
16 Mahmood et al.
(a)
(b) (c)
(d)
Figure 18. (a) Cross-sectional view, (b) patch layer, and (c) ground layer, (d) fabricated antenna [115].
As an approximation to the phantom, the frequency-modulated spanned from (2.3–2.68) GHz

with (33)% moderate percentage bandwidth at (2.6) dBi maximum gain. It was confirmed through
several compressive experiments that an antenna manufactured using this method could withstand
physical curvature and machine washing while retaining its re-configurability. Such findings validate the
usefulness of the proposed strategy to realize versatile adjustable electronically tunable antennas with
different re-configurability forms. Hence, the design can be an appropriate candidate for new wireless
wearable systems. Meanwhile and in the same field, a modern lightweight UWB antenna was introduced
by Simorangkir et al. [116] for portable applications, which was extremely sensitive to human body
mounting and physical deformation. The proposed antenna depicted in Figure 19 used two conductive
fabric embedded polymer (PDMS) to realize the robustness and flexibility. These PDMS based
substrates were the combination of nickel-copper-silver-coated nylon ripstop with (σ = 1.02 × 105) S/m
and nickel-copper coated ripstop with (σ = 5.4 × 104) S/m. The antenna preferences had been shown
firstly by retaining a complete ground plane that provided the requisite separation between the antenna
and the human body while wearing. The expectations of the antenna were evidenced by the intense
physical robustness applied to the PDMS embedded conductive fabric manufacturing technologies. In
the phantom-based on-body measurement, the antenna reached (6) GHz with the operation and in (3.68–
10.1) GHz, (4.53) dBi total gain and (27)% total efficiency relative to free space measurements. As a
result of this, the proposed antenna can be a good candidate for UWB wearable applications, knowing
that the employed lossy materials alongside with antenna efficiency need to get further optimization.
(a) (b)
Figure 19. (a) Proposed UWB antenna. (b) Fabricated UWB antenna [116].
(a) (b)
Figure 20. PDMS-embedded antenna. (a) Dual-band. (b) Frequency-reconfigurable [117].
Furthermore, a recent solution to the realization of robust, lightweight wireless antennas was
adequately demonstrated by Simorangkir et al. [117]. This work addressed the design, manufacture,
and calculation of two antennas identified as dual-band dual-mode (see Figure 20(a)) and a frequency-
reconfigurable patch antenna (see Figure 20(b)) as a test platform. The PDMS-based conductive fabric
antenna was fabricated using NCS95R-CR in the patch and nickel copper-coated ripstop fabric in the
ground plane.
Certain laboratory studies confirmed that antennas produced with the suggested method can resist
physical curvature and machine washing, validating the suitability of this method to the effective
application of both passive and active versatile wearable antennas. In [118], a dual-band, coplanar,
versatile antenna was mounted based on silver ink on a paper substrate introduced by Baytöre et
al. The designed antenna was inexpensive and straightforward to produce because it was based on
photographic paper that is simple to procure commercially. An inkjet printer with conductive silver
(Ag) Nano ink was used for manufacturing electrically conductive flexible circuits of the antenna. The
resonance frequency of the antenna was shifted marginally owing to the instabilities occurred during
bending conditions. For further BPMS based conductive fabric antenna, Simorangkir et al. [119] studied
the operative keys of the challenging humble PDMS metal used in the fabrication of flexible antenna
employed in wearable applications. The system incorporates the use of conductive cloth as a radiator
with PDMS, which concurrently serves as a substrate and as a secure encapsulation. Four PDMS-
ceramic composition woven conducting fabrics defined by (nickel-copper silver-coated nylon ripstop,
copper-coated polyester taffeta, nickel copper-coated ripstop and silver-coated ripstop) were selected
among the available conductive fabrics. The use of a PDMS-ceramic composite as part of the substrate
of the antenna results in a scale decrease of over 50 percent relative to a mere PDMS (see Figure 21).
The manufactured antennas were evaluated in different wearable circumstances, and hence
consistent efficiency was achieved even after dealing with severe circumference such as extraordinary
bending and machine washing. Owing to the validity of researches in the scope of potential applications
ranging from healthcare surveillance, protection, defense, and entertainment, significant research efforts
have been made over the last few years on wearable electronics. A considerable number of work
(a) (c)
(b) (d)
Figure 21. Designed antennas. (a) PA. (b) RFPA, Fabricated. (c) PA. (d) RFPA (dimensions in
mm) [119].
18 Mahmood et al.
(a) (b)
Figure 22. (a) Antenna geometry. (b) Fabricated prototype of the antenna [124].
activities were organized in which non-conventional substrates such as conductive fabrics [115, 116],
copper tapes [120], silver paste [121], conductive ink [122] and conductive threads [123] are employed
in antenna fabrication. Hence, upon testing a transparent flexible antenna built from translucent
conductive fabric embedded in PDMS, it is assumed that the approach suggested by Sayem et al. [124]
was appropriate for the manufacture of the translucent wearable antenna. Since the fabric is quite soft,
it binds tightly to PDMS, increasing the structural robustness. The prototype of the antenna shown in
Figure 22 was produced using VeilShield transparent conductive fabric and realized 2.45 GHz operational
range suitable for ISM applications. This work reported one drawback, which was the increased sheet
resistance after embedding, leading to a reduction in antenna gain. In contrast, the proposed approach
resulted that the antenna is almost transparent, lightweight, and robust.
Due to the difficulty of the working setting, the antennas added to WBAN are needed to equip
comprehensive functionality. A circularly polarized (CP) portable antenna was designed by Li et al. [125]
based on the FDM platform (fused deposition modeling) as exposed in Figure 23. The conductive cloth
was used on the NinjaFlex substrate to realize conductive sections of the patch antenna. The antenna
was encapsulated with additional NinjaFlex layers, realizing 2.45 GHz operating frequency based on the
modified patch. Bending and washing experiments were conducted to verify the output consistency, and
a strong agreement was found between simulated and calculated effects. The tests indicated that the
antenna realized (11)% bandwidth (1.8) dBi peak gain, (30.7)% antenna efficiency, and around (70) MHz
for ARBW. Owing to its compact design, low profile, CP radiation, durability, washing capability, and
(a) (b)
Figure 23. (a) Proposed antenna. (b) Photographs of the fabricated CP antenna [125].
(a) (b)
Figure 24. (a) The patch antenna design. (b) Comparison of S11 for transparent [132].
security, the designed scheme will be an attractive candidate for WLAN, WiMAX, and WiFi applications
on the human body.
In any contact device, antennas are useful for radiating or receiving electromagnetic waves [126].
Wireless networking has shown different antenna architecture developments, such as meta-material
antennas [127, 128], fractal antennas [129], UWB and modular antennas [130, 131]. Based on these
conductive materials, two specific forms of transparent and non-transparent versatile antennas (see
Figure 24) were tested by Kantharia et al. [132] based on various criteria such as gain, return loss and
radiation pattern. In contrast to the non-transparent antenna, a transparent antenna is inconspicuous
and can be used in several technologies. In terms of return loss and impedance bandwidth, the employed
conductive materials which are versatile provide excellent efficiency. Accordingly, the gain and radiation
pattern was compatible at the target wavelength, rendering the proposed antenna ideal for wireless
applications.
Table 3. Overview of the conductive materials.
Conductive Frequency
Ref. Substrate (σ) — S/m εr Size
Material (GHz)
[111] Polypropylene ECGT Fabric 2.09 × 107 2.2 48 × 46 2.021 and 2.052
[115] PDMS Nylon ripstop — 2.82 59.8 × 59.8 2.3–2.68
Nickel nylon
[116] 1.02 × 105
ripstop
PDMS 2.7 80 × 67 3.68–10.1
[117] Nickel ripstop 5.4 × 104
[118] Paper Silver Nano Ink — 3.6 48.2 × 48.2 2, 2.45, and 3
Nylon ripstop 7.7 × 105
Polyester
2.5 × 105 2.7 — 2.45
taffeta
[119] PDMS
Ripstop 4.2 × 105
Silver coated
8 × 104
ripstop
VeilShield
[124] PDMS — — 60 × 55 2.45
transparent
Embedded
[125] NinjaFlex — 3 60 × 60 2.45
NinjaFlex
PET AgHT-4 2.5 2.42 and 3.88
[132] — 45.13 × 53.21
Jeans Copper 1.7 2.93 and 5.71
20 Mahmood et al.
Finally, the overall arguments on the researches given in the aforementioned investigations regarding
Section 4 were summarized as exposed in Table 3.
5. SUMMARY
A variety of possible materials is available that could be used to build portable antennas. To have
an antenna configuration that fits the functional antenna requirements, SAR analysis, comparisons of
various antenna bending, and body comparisons must be performed. Wearable antennas are exciting,
and along with the rapidly increasing wireless networking technologies, they promise a fantastic future.
Reports of patch antennas have primarily concentrated on lightweight materials for the creation of
portable antennas. The characteristics of the employed materials affect the actions of an antenna. The
bandwidth and performance of a planar microstrip antenna, for instance, are primarily defined by the
dielectric constant and thickness of the substrate. The usage of textiles in portable antennas demands
their structures to be characterized. It is predicted that the conductive fibers should have weak and
reliable electrical resistance to reduce losses. Component durability is also necessary to enable the
antenna to be deformed over the fabric. Substrate selection is a crucial phase in the construction of
a garment or woven antenna, to be durable for a specific use. The developed wearable antennas are
primarily planar microstrip patch antennas, as they radiate mostly perpendicular to the planar structure
and their ground plane often supports the human body effectively.
Textiles typically have a relatively small dielectric constant, which decreases surface wave losses
and improves the antenna impedance bandwidth. For portable antennas, textile fabrics are chosen
with respect to performance and versatility. It raises the spatial waves and thus improves the antenna
impedance spectrum resulting in improved antenna resonance frequency, enabling antennas to grow
with reasonable performance and high gain. For the modeling antennas, the thickness of the dielectric
content can often be used to optimize the bandwidth of the planar antenna, knowing that this interest,
therefore, cannot maximize the performance of the antenna. Hence the option of the thickness for the
dielectric material is a balance between the output and bandwidth of the antenna. The substratum
thickness often impacts the structural size of the antenna. The design of an integrated wearable antenna
is critical, negotiating the trade-off between the efficiency of the antenna, its scale, and the difficulty
for the continuous development of WBAN applications. The most prominent concern is the absorption
of radiation in the human body owing to its relation to the antenna; therefore, the SAR value must be
lowered as far as possible. Other problems with these antennas need to address the reliability under
wet environments, impact on the atmosphere, dielectric properties, features of radiation around human
skin, etc.
Throughout the activity, textile antennas are expected to be bent or otherwise conformed to a
certain surface, and so experiments under different bending scenarios are required to examine differences
in bending-dependent morphology. A bendable antenna was invented to be mounted on the body of the
person. Mechanical deformation such as folding is possible when applied using textiles or lightweight
fabrics since human or living beings often use wearable antennas. Wearable antennas should be built
to be as symmetrical as possible in such a manner as to impact them while being bent in numerous
directions minimally. Noteworthy, AMC systems have been found to be less prone to mechanical
deformation in wearable devices. It has also been shown that utilizing the meta-surface, the consequences
of stretching, and the presence of the human body in its vicinity can be mitigated. Furthermore, bending
influences their radiation efficiency as predicted in the case of wearable CP antennas. Instead, owing to
variations in its efficient range, bending influences the resonant frequency of linearly polarized antennas.
Moreover, external curvature is one of the critical issues to ensure that portable antennas work
efficiently. While changing the frequency response of the wearable antennas, due to variations in the
initial concentration on the radiating components, it also influences the polarization. To end with this,
it must be remembered that the level of bending influences the resonant frequency of the antenna, the
SAR intensity, and the pattern of radiation. It is crucial to formulate certain strategies to remove
such consequences in order to build a wearable antenna. Additionally, a person must aim to position
an antenna such that it will not be bent along the y-axis since it will cause a more severe loss of
efficiency. Last, the antenna should be rendered as low as necessary through bending to prevent the
major difference in the overall duration of the antenna.For further material analysis, upon testing a
clear, flexible antenna built from translucent conductive fabric embedded in PDMS it is assumed that
the existing approach is appropriate for the manufacture of transparent wearable antennas. As a result,
the textile substrate is a strong choice, since it binds tightly to PDMS, increasing structural effectiveness
of an antenna. The only downside in such type is the decreased surface resistance after embedding that
contributes to a loss in antenna gain.
6. CONCLUSIONS
Wearable antennas are one of the main elements of wearable and portable equipment design. They are
suitable for worn-out wireless networking and sensing applications owing to their lightweight, versatility,
relatively inexpensive, and conformal features. This analysis ends with the introduction of applications
where wearable technologies are considered to be of maximum value. Furthermore, the paper addressed
the forms of versatile materials used and state-of-the-art technology employed to realize such constructs.
The choice of material styles may be rendered dependent on factors such as specification, operational
frequency bands, smallest-dimensional precision, smooth fitting into wearer garments, robustness to the
rough environment, and the impact of bending scenarios. Although antenna requires low-loss dielectric
material and highly conductive materials for effective receipt/transmission of EM radiation, extremely
conductive products include aluminum, metallic inks, conductive polymers, and PDMS integrated
conductive fibers are modern varieties used as wearable antenna conductive components. On the other
side, due to its lightweight properties, several versatile substrate materials were presented as perfect
solutions. It is inferred from the analysis that the most critical part of the specification is to eliminate
coupling with the body while incorporating additional functionality to the layout of the antenna. This
aspect intended to maintain stable antenna function on the body, accompanied by more improvements
such as bandwidth extension as well as allow the antenna to operate with optimized performance with
respect to the type of antenna topology. Finally, the paper studied the bendable antennas in several
radiuses and analyzed their impact on the performance of the antenna. Consequently, it can be noted
that the bending degree affects the resonant frequency, SAR strength, and radiation pattern of an
antenna.
ACKNOWLEDGMENT
The authors wish to convey their gratitude to the Department of Electrical and Electronic Engineering of
Universiti Putra Malaysia (UPM) for funding this research work. This research is financially supported
by a Putra Grant from Universiti Putra Malaysia, GP-IPS/9606000.
REFERENCES
1. Paracha, K. N., et al., “Wearable antennas: A review of materials, structures, and innovative
features for autonomous communication and sensing,” IEEE Access, Vol. 7, 56694–56712, 2019.
2. Bhattacharyya, S., et al., Handbook of Research on Recent Developments in Intelligent
Communication Application, IGI Global, 2016.
3. Chan, M., et al., “Smart wearable systems: Current status and future challenges,” Artificial
Intelligence in Medicine, Vol. 56, No. 3, 137–156, 2012.
4. Hu, J., “Overview of flexible electronics from ITRI’s viewpoint,” 2010 28th VLSI Test Symposium
(VTS), IEEE, 2010.
5. Werner, D. H. and Z. H. Jiang, Electromagnetics of Body Area Networks: Antennas, Propagation,
and RF Systems, John Wiley & Sons, 2016.
6. Patel, M. and J. Wang, “Applications, challenges, and prospective in emerging body area
networking technologies,” IEEE Wireless Communications, Vol. 17, No. 1, 80–88, 2010.
7. Ali, S. M., et al., “Design of dual-band wearable crescent-shaped button antenna for WLAN
applications,” Intelligent Computing and Innovation on Data Science, 457–464, Springer, 2020.
8. Seyedi, M., et al., “A survey on intrabody communications for body area network applications,”
IEEE Transactions on Biomedical Engineering, Vol. 60, No. 8, 2067–2079, 2013.
22 Mahmood et al.
9. Wang, D., M. Ghosh, and D. Smith, “Medical Body Area Network (MBAN) with key-based
control of spectrum usage,” Google Patents, 2017.
10. Hertleer, C., et al., “A textile antenna for off-body communication integrated into protective
clothing for firefighters,” IEEE Transactions on Antennas and Propagation, Vol. 57, No. 4, 919–
925, 2009.
11. Wu, J.-W., et al., “Dual broadband design of rectangular slot antenna for 2.4 and 5 GHz wireless
communication,” Electronics Letters, Vol. 40, No. 23, 1461–1463, 2004.
12. Raj, R. K., et al., “A new compact microstrip-fed dual-band coplanar antenna for WLAN
applications,” IEEE Transactions on Antennas and Propagation, Vol. 54, No. 12, 3755–3762,
2006.
13. Sopa, P. and P. Rakluea, “The hexagonal shaped UWB wearable textile antenna with band-
notched characteristics,” 2020 8th International Electrical Engineering Congress (iEECON),
IEEE, 2020.
14. Garg, R., et al., Microstrip Antenna Design Handbook, Artech House, 2001.
15. Ma, L., R. Edwards, and S. Bashir, “A wearable monopole antenna for ultra wideband with
notching function,” 2008.
16. Yan, S., P. J. Soh, and G. A. Vandenbosch, “Compact all-textile dual-band antenna loaded
with metamaterial-inspired structure,” IEEE Antennas and Wireless Propagation Letters, Vol. 14,
1486–1489, 2014.
17. Ashyap, A. Y., et al., “Compact and low-profile textile EBG-based antenna for wearable medical
applications,” IEEE Antennas and Wireless Propagation Letters, Vol. 16, 2550–2553, 2017.
18. Ashyap, A. Y., et al., “Robust low-profile electromagnetic band-gap-based on textile wearable
antennas for medical application,” 2017 International Workshop on Antenna Technology: Small
Antennas, Innovative Structures, and Applications (iWAT), IEEE, 2017.
19. Salonen, P., Y. Rahmat-Samii, and M. Kivikoski, “Wearable antennas in the vicinity of human
body,” IEEE Antennas and Propagation Society Symposium, 2004, IEEE, 2004.
20. Zhu, S. and R. Langley, “Dual-band wearable antennas over EBG substrate,” Electronics Letters,
Vol. 43, No. 3, 141–142, 2007.
21. Liu, F.-X., et al., “Wearable applications of quarter-wave patch and half-mode cavity antennas,”
IEEE Antennas and Wireless Propagation Letters, Vol. 14, 1478–1481, 2014.
22. Liu, Y., et al., “An improved design of wearable strain sensor based on knitted RFID technology,”
2016 IEEE Conference on Antenna Measurements & Applications (CAMA), IEEE, 2016.
23. Gupta, B., S. Sankaralingam, and S. Dhar, “Development of wearable and implantable antennas
in the last decade: A review,” 2010 10th Mediterranean Microwave Symposium, IEEE, 2010.
24. George, G., et al., “Design of meander line wearable antenna,” 2013 IEEE Conference on
Information & Communication Technologies, IEEE, 2013.
25. Kaufmann, T., et al., “Efficiency of a compact elliptical planar ultra-wideband antenna based on
conductive polymers,” International Journal of Antennas and Propagation, Vol. 2012, 2012.
26. Reyes-Vera, E., M. Arias-Correa, A. Giraldo-Muno, D. Catano-Ochoa, and J. Santa-Marin,
“Development of an improved response ultra-wideband antenna based on conductive adhesive
of carbon composite,” Progress In Electromagnetics Research C, Vol. 79, 199–208, 2017.
27. Hwang, J.-N. and F.-C. Chen, “Reduction of the peak SAR in the human head with
metamaterials,” IEEE Transactions on Antennas and Propagation, Vol. 54, No. 12, 3763–3770,
2006.
28. Shirakawa, H., et al., “Synthesis of electrically conducting organic polymers: Halogen derivatives
of polyacetylene, (CH) x,” Journal of the Chemical Society, Chemical Communications, Vol. 16,
578–580, 1977.
29. Jayabharathy, K. and T. Shanmuganantham, “Design of a compact textile wideband antenna for
smart clothing,” 2019 2nd International Conference on Intelligent Computing, Instrumentation
and Control Technologies (ICICICT), IEEE, 2019.
30. Klemm, M. and G. Troester, “Textile UWB antennas for wireless body area networks,” IEEE
Transactions on Antennas and propagation, Vol. 54, No. 11, 3192–3197, 2006.
31. Kennedy, T. F., et al., “Body-worn E-textile antennas: The good, the low-mass, and the
conformal,” IEEE Transactions on Antennas and Propagation, Vol. 57, No. 4, 910–918, 2009.
32. Bai, Q. and R. Langley, “Crumpling of PIFA textile antenna,” IEEE Transactions on Antennas
and Propagation, Vol. 60, No. 1, 63–70, 2011.
33. Lilja, J., et al., “Design and manufacturing of robust textile antennas for harsh environments,”
IEEE Transactions on Antennas and Propagation, Vol. 60, No. 9, 4130–4140, 2012.
34. Huang, J. S., et al., “A novel textile antenna using composite multifilament conductive threads
for smart clothing applications,” Microwave and Optical Technology Letters, Vol. 58, No. 5, 1232–
1236, 2016.
35. Xiaomu, H., S. Yan, and G. A. Vandenbosch, “Wearable button antenna for dual-band WLAN
applications with combined on and off-body radiation patterns,” IEEE Transactions on Antennas
and Propagation, Vol. 65, No. 3, 1384–1387, 2017.
36. Ouyang, Y. and W. J. Chappell, “High frequency properties of electro-textiles for wearable antenna
applications,” IEEE Transactions on Antennas and Propagation, Vol. 56, No. 2, 381–389, 2008.
37. Mohan, D. and C. Suriyakala, “Ergonomics of textile antenna for body centric wireless networks for
UWB application,” 2017 International Conference on Circuit, Power and Computing Technologies
(ICCPCT), IEEE, 2017.
38. Al-Sehemi, A. G., et al., “Flexible and small wearable antenna for wireless body area network
applications,” Journal of Electromagnetic Waves and Applications, Vol. 31, No. 11–12, 1063–1082,
2017.
39. Oni, M. A. I. and M. T. Ali, “Design of a compact, low-profile, elliptical patch UWB antenna and
performance analysis in vicinity of human layered tissue model for wireless body area network
(WBAN) applications,” International Journal of Innovation and Applied Studies, Vol. 8, No. 4,
1770, 2014.
40. Yang, H.-L., W. Yao, Y. Yi, X. Huang, S. Wu, and B. Xiao, “A dual-band low-profile metasurface-
enabled wearable antenna for WLAN devices,” Progress In Electromagnetics Research, Vol. 61,
115–125, 2016.
41. Yan, S., et al., “On-body performance of wearable UWB textile antenna with full ground plane,”
2016 10th European Conference on Antennas and Propagation (EuCAP), IEEE, 2016.
42. Turkmen, M. and H. Yalduz, “Design and performance analysis of a flexible UWB wearable textile
antenna on jeans substrate,” International Journal of Information and Electronics Engineering,
Vol. 8, No. 2, 15–18, 2018.
43. Wang, K.-h. and J.-S. Li, “Jeans textile antenna for smart wearable antenna,” 2018 12th
International Symposium on Antennas, Propagation and EM Theory (ISAPE), IEEE, 2018.
44. Li, S.-H. and J.-S. Li, “Smart patch wearable antenna on Jeans textile for body wireless
communication,” 2018 12th International Symposium on Antennas, Propagation and EM Theory
(ISAPE), IEEE, 2018.
45. Osman, M. A., et al., “Design and analysis UWB wearable textile antenna,” Proceedings of the
5th European Conference on Antennas and Propagation (EUCAP), IEEE, 2011.
46. Amit, S., V. Talasila, and P. Shastry, “A semi-circular slot textile antenna for ultrawideband
applications,” 2019 IEEE International Symposium on Antennas and Propagation and USNC-
URSI Radio Science Meeting, IEEE, 2019.
47. Chandra, R., et al., “On the opportunities and challenges in microwave medical sensing and
imaging,” IEEE Transactions on Biomedical Engineering, Vol. 62, No. 7, 1667–1682, 2015.
48. Saeidi, T., et al., “Equivalent Circuit (EC) approximation of miniaturized elliptical UWB antenna
for imaging of wood,” Intelligent Computing and Innovation on Data Science, 447–455, Springer,
2020.
49. Alani, S., Z. Zakaria, and A. Ahmad, “Miniaturized UWB elliptical patch antenna for skin cancer
diagnosis imaging,” International Journal of Electrical & Computer Engineering, Vol. 10, 2088–
24 Mahmood et al.
8708, 2020.
50. Mohammed, B. J., et al., “Microwave system for head imaging,” IEEE Transactions on
Instrumentation and Measurement, Vol. 63, No. 1, 117–123, 2013.
51. Meaney, P. M., et al., “Microwave imaging for neoadjuvant chemotherapy monitoring: Initial
clinical experience,” Breast Cancer Research, Vol. 15, No. 2, R35, 2013.
52. Fear, E. C., et al., “Confocal microwave imaging for breast cancer detection: Localization of
tumors in three dimensions,” IEEE Transactions on Biomedical Engineering, Vol. 49, No. 8, 812–
822, 2002.
53. Klemm, M., et al., “Radar-based breast cancer detection using a hemispherical antenna array —
Experimental results,” IEEE Transactions on Antennas and Propagation, Vol. 57, No. 6, 1692–
1704, 2009.
54. Golnabi, A. H., et al., “Microwave tomography for bone imaging,” 2011 IEEE International
Symposium on Biomedical Imaging: From Nano to Macro, IEEE, 2011.
55. Chandra, R., et al., “A microwave imaging-based technique to localize an in-body RF source for
biomedical applications,” IEEE Transactions on Biomedical Engineering, Vol. 62, No. 5, 1231–
1241, 2014.
56. Augustine, R., et al., “Microwave reflectivity analysis of bone mineral density using ultra wide
band antenna,” Microwave and Optical Technology Letters, Vol. 59, No. 1, 21–26, 2017.
57. Lin, X., et al., “Ultra-wideband textile antenna for wearable microwave medical imaging
58. Abbas, A., et al., “A rectangular notch-band UWB antenna with controllable notched bandwidth
and centre frequency,” Sensors, Vol. 20, No. 3, 777, 2020.
59. El Gharbi, M., et al., “A novel ultra-wide band wearable antenna under different bending
conditions for electronic-textile applications,” The Journal of The Textile Institute, 1–7, 2020.
60. Di Natale, A. and E. Di Giampaolo, “A reconfigurable all-textile wearable UWB antenna,”
Progress In Electromagnetics Research C, Vol. 103, 31–43, 2020.
61. Kong, Y., Y. Li, and K. Yu, “A minimized MIMO-UWB antenna with high isolation and triple
band-notched functions,” Frequenz, Vol. 70, No. 11–12, 463–471, 2016.
62. Kong, Y., et al., “A quadruple band-notched UWB antenna by using arc-shaped slot and rotated
E-shaped resonator,” Applied Computational Electromagnetics Society Journal, Vol. 31, No. 11,
2016.
63. Li, Y., W. Zhang, and W. Yu, “A circular slot UWB antenna with independently tunable quad-
band filtering characteristics,” Applied Computational Electromagnetics Society Journal, Vol. 30,
No. 10, 2015.
64. Li, Y., W. Li, and Q. Ye, “A reconfigurable triple-notch-band antenna integrated with
defected microstrip structure band-stop filter for ultra-wideband cognitive radio applications,”
International Journal of Antennas and Propagation, Vol. 2013, 2013.
65. Li, Y., W. Li, and W. Yu, “A multi-band/UWB MIMO/diversity antenna with an enhance
isolation using radial stub loaded resonator,” Applied Computational Electromagnetics Society
Journal, Vol. 28, No. 1, 8–20, 2013.
66. Li, Y., W. Li, and W. Yu, “A switchable UWB slot antenna using SIS-HSIR and SIS-SIR for
multi-mode wireless communications applications,” ACES Journal — Applied Computational
Electromagnetics Society. Vol. 27, No. 4, 340, 2012.
67. Mohandoss, S., et al., “On the bending and time domain analysis of compact wideband flexible
monopole antennas,” AEU — International Journal of Electronics and Communications, Vol. 101,
168–181, 2019.
68. Kumari, S. and V. R. Gupta, “Measurement of specific absorption rate of monopole patch antenna
on human arm,” International Journal of Microwave and Optical Technology, Vol. 10, No. 3, 190–
194, 2015.
69. Elias, N., et al., “The effects of human body and bending on dipole textile antenna performance
and SAR,” 2012 Asia Pacific Microwave Conference Proceedings, IEEE, 2012.
70. Bala, R., et al., “Wearable graphene based curved patch antenna for medical telemetry
applications,” Applied Computational Electromagnetics Society Journal, Vol. 31, No. 5, 2016.
71. Liu, J., et al., “Bending effects on a flexible Yagi-Uda antenna for wireless body area network,”
2016 Asia-Pacific International Symposium on Electromagnetic Compatibility (APEMC), IEEE,
2016.
72. Cavallari, R., et al., “A survey on wireless body area networks: Technologies and design
challenges,” IEEE Communications Surveys & Tutorials, Vol. 16, No. 3, 1635–1657, 2014.
73. Ferreira, D., et al., “Wearable textile antennas: Examining the effect of bending on their
performance,” IEEE Antennas and Propagation Magazine, Vol. 59, No. 3, 54–59, 2017.
74. Alsariera, H., et al., “Simple broadband circularly polarized monopole antenna with two
asymmetrically connected U-shaped parasitic strips and defective ground plane,” Telkomnika,
Vol. 18, No. 3, 1169–1175, 2020.
75. Dey, S., N. Saha, and S. Biswas, “Design and performance analysis of UWB circular disc monopole
textile antenna and bending consequences,” Proceedings of the 5th European Conference on
Antennas and Propagation (EUCAP), IEEE, 2011.
76. Kim, J. and H. Lee, “Low specific absorption rate wearable antenna for WLAN band applications,”
Proceedings of the Fourth European Conference on Antennas and Propagation, IEEE, 2010.
77. Bai, Q. and R. Langley, “Wearable EBG antenna bending and crumpling,” 2009 Loughborough
Antennas & Propagation Conference, IEEE, 2009.
78. Amaro, N., C. Mendes, and P. Pinho, “Bending effects on a textile microstrip antenna,” 2011
IEEE International Symposium on Antennas and Propagation (APSURSI), IEEE, 2011.
79. Isa, M., et al., “Textile dual band circular ring patch antenna under bending condition,” Journal
of Telecommunication, Electronic and Computer Engineering (JTEC), Vol. 9, No. 3, 37–43, 2017.
80. Hall, P. S. and Y. Hao, Antennas and Propagation for Body-centric Wireless Communications,
Artech House, 2012.
81. Astrin, A., “IEEE standard for local and metropolitan area networks part 15.6: Wireless body
area networks: IEEE std 802.15. 6-2012,” the document is available at IEEE Xplore, Vol. 550,
2012.
82. El Hajj, W., C. Person, and J. Wiart, “A novel investigation of a broadband integrated inverted-
F antenna design; application for wearable antenna,” IEEE Transactions on Antennas and
Propagation, Vol. 62, No. 7, 3843–3846, 2014.
83. Mandal, B. and S. Parui, “Wearable tri-band SIW based antenna on leather substrate,” Electronics
Letters, Vol. 51, No. 20, 1563–1564, 2015.
84. Lee, C. M., et al., “A flexible and transparent antenna on a polyamide substrate for laptop
computers,” Microwave and Optical Technology Letters, Vol. 57, No. 5, 1038–1042, 2015.
85. Mersani, A., L. Osman, and J.-M. Ribero, “Flexible UWB AMC antenna for early stage skin
cancer identification,” Progress In Electromagnetics Research M, Vol. 80, 71–81, 2019.
86. Rais, N. H. M., et al., “Dual-band suspended-plate wearable textile antenna,” IEEE Antennas
and Wireless Propagation Letters, Vol. 12, 583–586, 2013.
87. Whittow, W. G., et al., “Inkjet-printed microstrip patch antennas realized on textile for wearable
88. Chen, S. J. and C. Fumeaux, “Wearable antennas based on graphite paper and conductive
polymer,” 2018.
89. Sabban, A., “Small wearable antennas for wireless communication and medical systems,” 2018
IEEE Radio and Wireless Symposium (RWS), IEEE, 2018.
90. Li, W.-Y., et al., “Conformai integrated multi-layer thin-film antenna by novel LITA technologies
for smartwatch wearable device applications,” 2016 International Symposium on Antennas and
Propagation (ISAP), IEEE, 2016.
91. Seman, F. C., F. Ramadhan, N. S. Ishak, R. Yuwono, Z. Z. Abidin, S. H. Dahlan, S. M. Shah, and
A. Y. I. Ashyap, “Performance evaluation of a star-shaped patch antenna on polyimide film under
various bending conditions,” Progress In Electromagnetics Research Letters, Vol. 85, 125–130,
26 Mahmood et al.
2019.
92. Gupta, N. P., M. Kumar, and R. Maheshwari, “Development and performance analysis of
conformal UWB wearable antenna under various bending radii,” IOP Conference Series: Materials
Science and Engineering, IOP Publishing, 2019.
93. Yin, B., J. Gu, X. Feng, B. Wang, Y. Yu, and W. Ruan, “A low SAR value wearable antenna for
wireless body area network based on AMC structure,” Progress In Electromagnetics Research C,
Vol. 95, 119–129, 2019.
94. Ismail, M. F., et al., “Bending analysis on circular polarization array textile antenna,” 2014 IEEE
Asia-Pacific Conference on Applied Electromagnetics (APACE), IEEE, 2014.
95. Kim, S., et al., “Monopole antenna with inkjet-printed EBG array on paper substrate for wearable
96. Bayram, Y., et al., “E-textile conductors and polymer composites for conformal lightweight
antennas,” IEEE Transactions on Antennas and Propagation, Vol. 58, No. 8, 2732–2736, 2010.
97. Chen, S. J., et al., “A modular textile antenna design using snap-on buttons for wearable
98. Wang, Z., et al., “Embroidered multiband body-worn antenna for GSM/PCS/WLAN
communications,” IEEE Transactions on Antennas and Propagation, Vol. 62, No. 6, 3321–3329,
2014.
99. Kiourti, A., et al., “UWB antennas on conductive textiles,” 2016 IEEE International Symposium
on Antennas and Propagation (APSURSI), IEEE, 2016.
100. Koulouridis, S., et al., “Polymer-ceramic composites for microwave applications: Fabrication and
performance assessment,” IEEE Transactions on Microwave Theory and Techniques, Vol. 54,
No. 12, 4202–4208, 2006.
101. Zhou, Y., et al., “Polymer-carbon nanotube sheets for conformal load bearing antennas,” IEEE
Transactions on Antennas and Propagation, Vol. 58, No. 7, 2169–2175, 2010.
102. Simorangkir, R. B., et al., “Dual-band dual-mode textile antenna on PDMS substrate for body-
centric communications,” IEEE Antennas and Wireless Propagation Letters, Vol. 16, 677–680,
2016.
103. Song, L., et al., “Stretchable and reversibly deformable radio frequency antennas based on silver
nanowires,” ACS Applied Materials & Interfaces, Vol. 6, No. 6, 4248–4253, 2014.
104. Huang, X., et al., “Highly flexible and conductive printed graphene for wireless wearable
communications applications,” Scientific Reports, Vol. 5, 18298, 2015.
105. Johnston, I., et al., “Mechanical characterization of bulk Sylgard 184 for microfluidics and
microengineering,” Journal of Micromechanics and Microengineering, Vol. 24, No. 3, 035017,
2014.
106. Sebastian, M. and L. Namitha, “Rubber-ceramic composites,” Microwave Materials and
Applications 2V Set, 537–574, Wiley, 2017.
107. Kumar, G. and K. P. Ray, Broadband Microstrip Antennas, Artech House, 2003.
108. Massey, P., “Mobile phone fabric antennas integrated within clothing,” Eleventh International
Conference on Antennas and Propagation, 2001, (IEE Conf. Publ. No. 480), Vol. 1, 2001.
109. Salonen, P., M. Keskilammi, and L. Sydanheimo, “A low-cost 2.45 GHz photonic band-gap patch
antenna for wearable systems,” Eleventh International Conference on Antennas and Propagation,
2001, (IEE Conf. Publ. No. 480), Vol. 2, 2001.
110. Tronquo, A., et al., “Robust planar textile antenna for wireless body LANs operating in 2.45 GHz
ISM band,” Electronics Letters, Vol. 42, No. 3, 142–143, 2006.
111. Gangopadhyay, S., et al., “Design and development of electro-conductive rectangular textile
antenna using polypropylene fabric,” 2017 4th IEEE Uttar Pradesh Section International
Conference on Electrical, Computer and Electronics (UPCON), IEEE, 2017.
112. Yan, S. and G. A. Vandenbosch, “Radiation pattern-reconfigurable wearable antenna based on
metamaterial structure,” IEEE Antennas and Wireless Propagation Letters, Vol. 15, 1715–1718,
2016.
113. Saeed, S. M., C. A. Balanis, and C. R. Birtcher, “Inkjet-printed flexible reconfigurable antenna for
conformal WLAN/WiMAX wireless devices,” IEEE Antennas and Wireless Propagation Letters,
Vol. 15, 1979–1982, 2016.
114. Mazlouman, S. J., et al., “A reconfigurable patch antenna using liquid metal embedded in a
silicone substrate,” IEEE Transactions on Antennas and Propagation, Vol. 59, No. 12, 4406–4412,
2011.
115. Simorangkir, R. B., et al., “A method to realize robust flexible electronically tunable antennas
using polymer-embedded conductive fabric,” IEEE Transactions on Antennas and Propagation,
Vol. 66, No. 1, 50–58, 2017.
116. Simorangkir, R. B., A. Kiourti, and K. P. Esselle, “UWB wearable antenna with a full ground
plane based on PDMS-embedded conductive fabric,” IEEE Antennas and Wireless Propagation
Letters, Vol. 17, No. 3, 493–496, 2018.
117. Simorangkir, R. B., Y. Yang, and K. P. Esselle, “Robust implementation of flexible wearable
antennas with PDMS-embedded conductive fabric,” 2018.
118. Baytöre, C., et al., “Coplanar flexible antenna design using conductive silver nano ink on paper
substrate for wearable antenna applications,” 2018 28th International Conference Radioelektronika
(RADIOELEKTRONIKA), IEEE, 2018.
119. Simorangkir, R. B., et al., “Polydimethylsiloxane-embedded conductive fabric: Characterization
and application for realization of robust passive and active flexible wearable antennas,” IEEE
Access, Vol. 6, 48102–48112, 2018.
120. Hu, B., et al., “Bending and on-arm effects on a wearable antenna for 2.45 GHz body area
network,” IEEE Antennas and Wireless Propagation Letters, Vol. 15, 378–381, 2015.
121. Ha, S.-J. and C. W. Jung, “Reconfigurable beam steering using a microstrip patch antenna with a
U-slot for wearable fabric applications,” IEEE Antennas and Wireless Propagation Letters, Vol. 10,
1228–1231, 2011.
122. Yang, L., et al., “RFID tag and RF structures on a paper substrate using inkjet-printing
technology,” IEEE Transactions on Microwave Theory and Techniques, Vol. 55, No. 12, 2894–
2901, 2007.
123. Zhang, S., et al., “Embroidered wearable antennas using conductive threads with different stitch
spacings,” 2012 Loughborough Antennas & Propagation Conference (LAPC), IEEE, 2012.
124. Sayem, A. S. M., et al., “Feasibility study of PDMS embedded transparent conductive fabric for
the realization of transparent flexible antennas,” 2019 13th European Conference on Antennas
and Propagation (EuCAP), IEEE, 2019.
125. Li, J., Y. Jiang, and X. Zhao, “Circularly polarized wearable antenna based on NinjaFlex-
embedded conductive fabric,” International Journal of Antennas and Propagation, Vol. 2019,
2019.
126. Balanis, C. A., Antenna Theory: Analysis and Design, John Wiley & Sons, 2016.
127. Upadhyaya, T. K., et al., “Miniaturization of tri band patch antenna using metamaterials,” 2012
Fourth International Conference on Computational Intelligence and Communication Networks,
IEEE, 2012.
128. Gnanagurunathan, G. and K. T. Selvan, “Metamaterial-based planar antennas,” Frontiers in
Electronic Technologies, 101–115, Springer, 2017.
129. Bhatt, S., et al., “Analysis of ultra wideband fractal antenna designs and their applications for
wireless communication: A survey,” 2017 International Conference on Inventive Systems and
Control (ICISC), IEEE, 2017.
130. Zhong, S., X. Yan, and X. Liang, “UWB planar antenna technology,” Frontiers of Electrical and
Electronic Engineering in China, Vol. 3, No. 2, 136–144, 2008.
131. Archevapanich, T., et al., “Ultra-wideband slot antenna on flexible substrate for
WLAN/WiMAX/UWB applications,” Asian Simulation Conference, Springer, 2014.
132. Kantharia, M., et al., “Performance evaluation of transparent and non-transparent flexible
antennas,” Optical and Wireless Technologies, 1–8, Springer, 2020.

Recent Advances in Wearable Antenna Technologies A Review

Uploaded by

Copyright:

Available Formats

Recent Advances in Wearable Antenna Technologies A Review

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Recent Advances in Wearable Antenna Technologies A Review

Uploaded by

Copyright:

Available Formats

Progress In Electromagnetics Research B, Vol.

89, 1–27, 2020

Recent Advances in Wearable Antenna Technologies: A Review

Sarmad N. Mahmood1, * , Asnor J. Ishak1 , Tale Saeidi2 , Hussein Alsariera3 ,

2. TEXTILE WEARABLE ANTENNAS

Figure 4. Front and back view of the antenna [29].

Table 1. Overview on textile wearable antennas.

3. BENDING SCENARIOS IN WEARABLE ANTENNAS

(a) (b) (c)

(a) (b) (c) (d)

(e) (f) (g) (h)

(a) (b) (c)

4. WEARABLE ANTENNA BASED CONDUCTIVE MATERIALS

Table 2. Overview on bending scenarios in wearable antennas.

(a) (b) (c)

As an approximation to the phantom, the frequency-modulated spanned from (2.3–2.68) GHz

Figure 20. PDMS-embedded antenna. (a) Dual-band. (b) Frequency-reconﬁgurable [117].

Table 3. Overview of the conductive materials.

You might also like