Scribd
Upload
29 views1 page

Chine Systems Inc Rob Zahensky FR Yer Ma Chine Systems Inc Rob Zahensky

This document describes parameters for setting the X address of manual pulse generators connected via I/O Link to a PMC controller. Parameter numbers 12340 to 12344 are used to set the PMC path for up to 5 manual pulse generators. Parameter 12310 sets the states of manual handle feed axis selection signals to control which axis is operated during manual feed or interrupt operations based on the handle used. The parameter values correspond to specific signal state combinations that map axes to handles.

Uploaded by

moisii teodora
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
29 views1 page

Chine Systems Inc Rob Zahensky FR Yer Ma Chine Systems Inc Rob Zahensky

This document describes parameters for setting the X address of manual pulse generators connected via I/O Link to a PMC controller. Parameter numbers 12340 to 12344 are used to set the PMC path for up to 5 manual pulse generators. Parameter 12310 sets the states of manual handle feed axis selection signals to control which axis is operated during manual feed or interrupt operations based on the handle used. The parameter values correspond to specific signal state combinations that map axes to handles.

Uploaded by

moisii teodora
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

B-64700EN/01 4.

DESCRIPTION OF PARAMETERS
[Valid data range] -1, 0 to 127, 200 to 327, 400 to 527, 600 to 727
To set X address of manual pulse generator connected with I/O Link in PMC.
When the manual pulse generator is not connected, set -1 to this parameter.
PMC Path X Address
1st. manual pulse generator No. 12340 No. 12300
2nd. manual pulse generator No. 12341 No. 12301
3rd. manual pulse generator No. 12342 No. 12302
4th. manual pulse generator No. 12343 No. 12303
5th. manual pulse generator No. 12344 No. 12304

Parameters No. 12340 to 12344 must be set as value showed in next table.
Value PMC Path
0
1st. PMC
1
2 2nd. PMC
3 3rd. PMC

NOTE
Set these parameters when bit 1 (HDX) of parameter No. 7105 is set
to 1. When HDX = 0, these parameters are automatically set. If a
manual handle is not connected when HDX = 0, -1 is set
automatically.

States of the manual handle feed axis selection signals when tool axis direction handle feed/interrupt
12310
and table-based vertical direction handle feed/interrupt are performed

[Input type] Parameter input


[Data type] Byte path
[Valid data range] 1 to Number of controlled axes
This parameter sets the states of the manual handle feed axis selection signal (HS1A to
HS1E for the first manual handle) or the manual handle interrupt axis selection signal
(HS1IA to HS1IE for the first manual handle) to perform tool axis direction handle
feed/interrupt and table-based vertical direction handle feed/interrupt.
The handle for which the signal states are set is determined by parameter No. 12323.

<Table of correspondence with the manual handle feed axis selection signals>
If parameter No. 12323 is set to 1, the states of the manual handle feed axis selection
signals or manual handle interrupt axis selection signals for the first manual handle in the
3-dimensional manual feed (handle feed) mode and corresponding parameter settings are
listed in the table below. When the first manual handle pulse generator is turned after
setting the signals corresponding to the value set in the parameter, operation is performed
in the specified mode.
If the value set in the parameter is larger than number of controlled axes, the movement is
not generated.
HS1E HS1D HS1C HS1B HS1A Parameter
(HS1IE) (HS1ID) (HS1IC) (HS1IB) (HS1IA) (No. 12310)
0 0 0 0 1 1
0 0 0 1 0 2
0 0 0 1 1 3
0 0 1 0 0 4
0 0 1 0 1 5
0 0 1 1 0 6
0 0 1 1 1 7
0 1 0 0 0 8

- 619 -

You might also like