Acer V193W

Service Guide
(for NT68167)

1
Service Guide Acer V193W

Service Guide Version and Revision

Version Release Date Revision History TPV model

T99SNFDYW7AFNCJ
A00 Apr-28-2010 Initial Release
T99ANFDYW7ZYNCJ

2
Service Guide Acer V193W
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.

Disclaimer
The information in this guide is subject to change without notice. Acer Incorporated makes no representations
or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any
warranties
of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual
is
sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer
Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Trademarks
Acer is a registered trademark of Acer Incorporated.
All other trademarks are property of their respective owners.

Conventions
The following conventions are used in this manual:

Screen messages Denotes actual messages that appear on screen.

Note Gives bits and pieces of additional information related to the current topic.
Warning Alerts you to any damage that might result from doing or not doing specific actions.
Caution Gives precautionary measures to avoid possible hardware or software problems.
Important Remind you to do specific actions relevant to the accomplishment of procedures.

3
Service Guide Acer V193W
Preface

Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office may have decided to extend the functionality of a machine (e.g. add-on
card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this
generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will not
be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office
may have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You
MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.

Warning: (For FCC Certified Models)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to
this equipment. It is the responsibility of the user to correct such interference.
As ENERGY STAR Partner our company has determined that this product meets the ENERGY STAR
guidelines for energy efficiency.

Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are
present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

4
Service Guide Acer V193W
Precautions

 Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool
or in a wet basement.

 Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and
cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the
manufacturer and follow the kit instructions.
 Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable
operation of the monitor and to protect it from overheating, be sure these openings are not blocked or
covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or
over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation
is provided.
 The monitor should be operated only from the type of power source indicated on the label. If you are not
sure of the type of power supplied to your home, consult your dealer or local power company.
 The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug
will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the
three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely.
Do not defeat the safety purpose of the grounded plug.

 Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect
the monitor from damage due to power surges.

 Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
 Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
 Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel
 To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V AC, Min. 5A.
 The wall socket shall be installed near the equipment and shall be easily accessible.

Special Notes On LCD Monitors

The following symptoms are normal with LCD monitor and do not indicate a problem.

Notes

 Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch
and then turn it on again to make sure the flicker disappears.
 You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
 The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a
missing pixel or a pixel lit all of the time.
 Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the
image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing
the image or turning off the Power Switch for hours.

5
Service Guide Acer V193W

Table Of Contents

Chapter 1 Monitor Features ………………………………………… 7

Introduction ……………………………………… 7
Monitor Block Diagram ……………………………………… 7
LCD Monitor General Specification ……………………………………… 8
Factory preset modes ……………………………………… 9
Connector Information ……………………………………… 9
Main Board Diagram ……………………………………… 10
Power Board Diagram ……………………………………… 10
Software Flow chart ……………………………………… 11

Chapter 2 LCD Panel Features ……………………………………… 12

General Features ……………………………………… 12

Electrical Characteristics ……………………………………… 12
BackLight Unit ……………………………………… 13
Panel Block Diagram ……………………………………… 13
Optical Characteristics ……………………………………… 14
LVDS pin assignment ……………………………………… 15

Chapter 3 Operating Instructions ……………………………………… 16

Installation ……………………………………… 16
Attaching/Removing the Base ……………………………………… 16
Front Button Controls ……………………………………… 17
eColor Management (OSD) ……………………………………… 18
How to Adjust a Setting ……………………………………… 19
OSD Message ……………………………………… 22
Factory Mode OSD ……………………………………… 23

Chapter 4 Machine Disassembly ……………………………………… 25

Disassembly Procedure ……………………………………… 25

Chapter 5 Troubleshooting ……………………………………… 29

Chapter 6 FRU (Field Replacement Unit) List ……………………………………… 34

Exploded Diagram ……………………………………… 34

Key components list ……………………………………… 35

Chapter 7 Schematic Diagram ……………………………………… 37

Chapter 8 PCB Layout ……………………………………… 45

6
Service Guide Acer V193W

Monitor Features Chapter 1

Introduction

This specification defines the requirements for the 19” MICROPROCESSOR based Multi-mode supported high
resolution color LCD monitor. This monitor can be directly connected to general 15-pin D-sub VGA connector,
also supports VESA DPMS power management and plug & play function.

The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no
radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more
desktop space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in
addition MTBF target is 50k hours or more.

Monitor Block Diagram

The LCD MONITOR will contain a main board, a power board, and key board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.

Monitor Function Block Diagram

Backlight 2-CCFL
Panel
LVDS

DC-AC inverter
Main Board
AC-DC(5V/12V)

Power Board

PC- VGA
Key board /DDC
AC supply
90V-264V
Input signal

7
Service Guide Acer V193W

LCD Monitor General Specification

Model ACER B/V193W

Driving system TFT Color LCD

Active Display Area 408.24 (H) x 255.15 (V)

Pixel pitch 0.2835(H) x 0.2835(W)

LCD Panel
Contrast Ratio 800 : 1

Response time 5ms

Luminance of White 300(Typ.) cd/㎡

Video signal R, G, B Analog D-Sub 15pin interface，

Separate Sync. H/V TTL

Input H-Frequency 30kHz – 80kHz

V-Frequency 55-75Hz

Dot Clock 140MHz(max)

Viewing angle (H)160 (V) 160(Type)

Display Colors 16.7M

Display mode 1440 x 900 @75Hz

ON Mode < 22.7W

EPA ENERGY STAR®
Saving/OFF Mode < 1W

Power Source 90 V ~ 240 V，50  3Hz, 60  3Hz

Operating Temp: 0° to 40°C

Environmental Storage Temp: -30° to 65°C
Considerations Operating Humidity: 0% to 90%
Storage Humidity: 0% to 90%

Peak surge current < 55A peak at 240 VAC and cold starting

No advance effects (no loss of information or defect) with a maximum of 1

Power line surge
half-wave missing per second

8
Service Guide Acer V193W

Factory preset modes

Mode Resolution
640 x 480@60Hz
VGA 640 x 480@72Hz
640 x 480@75Hz
800 x 600@56Hz
800 x 600@60Hz
SVGA
800 x 600@72Hz
800 x 600@75Hz
1024 x 768@60Hz
XGA 1024 x 768@70Hz
1024 x 768@75Hz
1152 x 864@75Hz
1280 x 960@60HZ
VESA 1280 x 720@60HZ
1280 x 768@60HZ
1280 x 768@75HZ
1280 x 1024@60Hz
SXGA
1280 x 1024@75Hz
1360 x 768@60HZ
WXGA 1440 x 900@60Hz
1440 x 900@75Hz

Connector Information
Input Signal Connector---- D-Sub 15pin Connector
Pin No. Description Pin No. Description
1. Red Input 9. +5VDC

2. Green Input 10. GND

3. Blue Input 11. RS232/GND

4. RS232/GND 12. SDA- DDC-Serial Data

5. Connection detect 13. H Sync

6. Red GND 14. V Sync

7. Green GND 15. SCL- DDC-Serial Clock

8. Blue GND

1 5
6
VGA Connector layout 10
11 15

9
Service Guide Acer V193W

MainBoard Block Diagram

Main Board Block Diagram Crystal12MHz LCD PANEL

(CN403/405)
(X401)
LVDS

SPI
FLASH ROM
Scalar IC NT68167 Novatak
SST25VF010A (Include ADC, OSD, MCU)
(U402) (U401)
H sync
DDC V sync
RGB
5V 3.3V 1.8V
Key Board D-Sub
Control Connector
(CN401/406) (CN101)

Voltage converter
（CN404） EEPROM
Video input
M24C04-WMN6TP
5V (U403)NC

PowerBoard Block Diagram

Fuse EMI Rectifier Smoothing Transformer 14V 14V

BD901 Capacitor Rectifier
C905 T901

AC input 5V 5V
100-240V Rectifier
IC-PWM MOS
Vcc Q901
IC901
Vcc
Rectifier

Power part Sense

resistor

regulating
PhotoCoupler Sampling

14V DC Switching MOS DC-AC Resonance NET High Voltage

Q802-AM9948 Transformer
Output
T801

PWM Control IC
Open Lamp Protection
DIM control IC801-TL494 2- CCFL

Inverter part
Current Sampling

10
Service Guide Acer V193W

Software Flow Chart

Start Software Flow Chart

Initial_MCU

Y
Check if DataBuffer Is blank To Write default values
Check if Sum is changed ?

Brightness
Contrast
Language Read parameter_from Buffer
InputType InputTimingStableCounter
Init_GlobalVariables OsdCounter
PowerDownCounter

Initial_MCU Device

while

PowerHandler

if standby mode?

No signal message InputTiming N

LED turn-on
Show power on logo
UnsupportModeFlag ModeHandler

InputTiming
OSD Menu MenuHandler Phaes/Frequency
Image setup
Color
O
if factory mode?
Y
Enter factory mode OSD

DebugHandler

END

11
Service Guide Acer V193W

LCD Panel Features Chapter 2

General Features
LTM190BT03 is a 19” wide TFT Liquid Crystal Display module with 2ch-LVDS interface. This module supports
1440 x 900 WXGA+ mode and can display 16.7M colors. High speed response(Typ 5ms).The inverter module
for Backlight is not built in. 2 CCFLs(Cold Cathode Fluorescent Lamp).

Electrical Characteristics

12
Service Guide Acer V193W

BackLight Unit

Panel Block Diagram for 2 CCFL

13
Service Guide Acer V193W

Optical Characteristics

14
Service Guide Acer V193W

LVDS pin assignment

15
Service Guide Acer V193W

Operating Instructions Chapter 3

Installation
To install the monitor on your host system, please follow the steps below:
1 Connect the video cable
A：Make sure both the monitor and computer are switched off.
B：Connect the VGA video cable to the computer.
2 Connect the power cord
Connect the power cord to the monitor, then to a properly grounded AC outlet.
3 Turn on the monitor and computer
Turn on the monitor first, then the computer. This sequence is very important.
4 If the monitor does not function properly, please refer to the troubleshooting section to diagnose the problem.

Attaching/Removing the Base

Attaching:
Align the release button on the bottom of the monitor with the corresponding slots on the bottom of the base.
Removing:
Press the release button as indicated, then pull in the direction of the arrow to remove the base.

16
Service Guide Acer V193W

Front Button Controls

Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
 The power cord should be connected.
 Connect the video cable from the monitor to the video card.
 Press the power button to turn on the monitor position. The power indicator will light up.

1 Power LED: Lights up to indicate the power is turned on.

2 Power Switch: Turn the power on or off.
3.4 < / > : Press < or > to navigate to the desired function, press Enter to select the function. Press < or > to
change the settings of the current function.
5 Menu/Enter: Activate the OSD menu when the OSD is off or activate deactivate the adjustment function when
the OSD is on.
6 Auto adjust button/Exit:
a. When the OSD menu is active, this button will act as the exit key exit OSD menu).
b. When the OSD menu is inactive, press this button for two seconds to activate the Auto Adjustment function.
The Auto Adjustment function s used to set the HPos, VPos, Clock and Focus.
7 Empowering Key/Exit:
a. When the OSD menu is active, this button will act as the exit key exit OSD menu).
b. When the OSD menu is inactive, press this button to select scenario mode.

NO Name Function

1 LED Power indicator

2 Power Switch Turn on / turn off.

3 > Right

4 < Left

5 Menu Menu/Enter

6 Auto Auto Adjustment /Exit

7 e Empowering Key/Exit

17
Service Guide Acer V193W

eColor Management (OSD)

18
Service Guide Acer V193W

How to Adjust a Setting

19
Service Guide Acer V193W
Adjusting the picture

20
Service Guide Acer V193W

21
Service Guide Acer V193W

OSD Message
a. Outline

b. The Description For OSD Message

Item Description

Auto Config When Analog signal input, if User Press Hot-Key “Auto”, will show this message, and the
Please Wait monitor do the auto config function.

Input Not When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor
Supported support range, will show this message. This message will be flying.

Cable Not Analog-Only Model: When the video cable is not connected, will show this message.
Connected This message will be flying.

Analog-Only Model: When the video cable is connected, but there is no active signal
No Signal
input, will show this message, then enter power saving.

Logo
When the monitor is power on, the LOGO will be showed in the center, and disappear slowly.

How To Optimize The DOS-Mode

Plug And Play
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the
monitor to inform the host system of its identity and, depending on the level of DDC used, communicate
additional information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information
over the DDC2B channel.

This monitor will appear to be non-functional if there is no video input signal. In order for this monitor
22
Service Guide Acer V193W
to operate properly, there must be a video input signal.

This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)
and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is
no video-input signal present. When there is no video input signals this monitor, following a time-out period, will
automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the
video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is
similar to a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or
clicking the mouse restores the display.

Using The Right Power Cord

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL
listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal computer: Please use a cord set
consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with
a grounding type attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates
with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European
counties.

Factory mode OSD

It is necessary that Factory mode is emerged for check the Panel and soft information .
for enter the Factory mode:

Conditions in the power-off, Press button and hold, press ,power on the monitor, then ,press MENU ,

the monitor will may enter Factory OSD Menu. Then Press MENU , Factory OSD Menu will appear in the
screen.

23
Service Guide Acer V193W

24
Service Guide Acer V193W

Machine Disassembly Chapter 4

This chapter contains step-by-step procedures on how to disassemble the monitor for maintenance.
Disassembly Procedure
1. Remove the cover hinge as the following indicator. (Fig 1)

Fig 1
2. Remove the screws as following indicate to release base stand. (Fig 2)

Fig 2

25
Service Guide Acer V193W
3. Remove the back cover and bezel.key board (Fig 3)

Fig 3

Fig 4

Fig 5

26
Service Guide Acer V193W
4. Remove the lamp connectors and the screw. (Fig 6-7)

Fig 6

Fig 7

27
Service Guide Acer V193W
5. Remove the screws to remove the panel. Put attention to the LVDS cable.(Fig8)

Fig 8
6. Remove the screws to remove the main board and power board.( Fig 9)

Fig 9

28
Service Guide Acer V193W

Troubleshooting Chapter 5
This chapter provides troubleshooting information for the V193W:
Main Board
1. No Power

No power Check flow chart

For the no power

Press power key and look if

the picture is normal

NG

Please reinsert and make sure the AC

100-240V is normal?

NG
Reinsert or check the power section
OK

Check 5V-CN701, 3.3V-U701-2;

NG Check&replace
OK CN701,U701,Q702,Q703,Q302,Q301

Check X401 waveform

NG
Replace X401
OK

Replace soft U402/U401

29
Service Guide Acer V193W

2. No Picture (LED is orange)

No picture Check flow chart

for the no signal

Check signal wire /button

NG
Replace signal wire
OK

Check U701 Vout=3.3V;

Q703-out=1.8V

NG replaceU701,Q703,Q702,Q406
OK &around device

check X401 waveform

NG
replace X401
OK
Check CN101-HS/VS
NG Check Correspondent
OK component

Check U402 out

NG
OK Updata soft data

Replace U401

3.White screen

Check flow chart

White screen
For the white screen

NG
Measure Q302-base Check X401 waveform
is low level?
NG
OK OK Replace X401

Check Q301=5V Check U403/U402

Or CN301 solder?

NG
NG Check around
Check around device
device
OK OK

Check connector Updata soft

Replace Panel Replace U402/U403/U401

30
Service Guide Acer V193W

4. Power Circuit No 14V/5V

NoPower Check flow chart

For the no power

Check CN901
100-240V？

NG
OK Check AC supply

Check rectified voltage-C905

NG Check FuseF901/ BD901
L902/C901/C902
OK

Check voltage of IC901-8pin

NG
OK check component R905/R920

Check T901(1-3)out-Vcc
NG
Check D901/R910/C911
OK

Check IC901-drive out

NG
OK Check/replace IC901

Check MOS-Q900pin(G/D)
NG
Check D910/R912/R915/Q901
Around component
OK

Check T901sub rectified out

5V/12V, Check rectified diode
NG D920/D921
&fiter capacitor

Chech opto-couple
IC902&IC903

Check-- open load

31
Service Guide Acer V193W

5. No Backlight of panel

Check flow chart for the

Check voltage of J801-12V？ Inverter No Backlight
NG
Open J801 voltage-12V
OK
NG
Check ON/OFFsignal Return check Power
OK
NG
Check main board After Power off,check
C804/C811/Q805/Q806
OK

Check IC801—11pin=5V？

NG After Power off,check

R802\C806\C809？
OK

Check IC801-3pin waveform?

NG
Check aroud C809\Q802
OK Replace IC801

Check IC801-pin6-8-9-10-PWM?

NG
replaceIC801
OK

Check Q805,Q806-Gate/Drain
NG Check ZD802/ZD803
R803/R804
OK
Replace device

Check PT801-out waveform

NG
Replace PT801
OK

Check the lamps of panel

&connector,feedback circuit

32
Service Guide Acer V193W

6. Key Board
OSD no working

OSD is unstable or not Check flow chart

working For the key board

Is Key Pad Board connecting Connect Key Pad Board

normally? NG

OK

Is Button Switch normally? Replace Button Switch

NG

OK

Is Key Pad Board normally? Replace Key Pad Board

NG
OK

Check Main Board

33
Service Guide Acer V193W

FRU (Field Replaceable Unit) List Chapter 6

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of V193W.Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part
number change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED
SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in
the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional
Acer office to order FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Note: The parts information listed below are for reference only, and are subject to change without notice. Please
go to http://cs.tpv.com.cn/hello1.asp for the latest information.

Exploded Diagram (Model: V193W)

34
Service Guide Acer V193W

Key components List

Exploded Diagram show the description of the following component.

Item Picture Description

1 Base

2 Main Frame

4 Panel

35
Service Guide Acer V193W

5 Power Board

6 Main Board

Symbol Description Symbol Description

U401 IC NT68167FG/D QFP64 CN101 D-SUB 15PIN
U402 SST25VF010A-33-4C-SAE CN403 FFC/FPC CONNECTOR
U102 IC AZC099-04S SOT23-6L CN404 WAFER 9P RIGHT ANELE PITCH
U103 IC AZC099-04S SOT23-6L CN406 WAFER 6PIN
X401 CRYSTAL 12MHz CN902 WIRE HARNESS 9P(SCN)-9P(PH)
NXS12.000AC30F-KAB10
U701 IC AZ1117D-3.3TRG1 1A/3.3V TO-252 CN901 AC socket
IC801 IC TL494IDR SOIC-16 Q901 2SK2645
IC901 LD7575PS SOP-8 E750 750GLS190BT3DCN0AC
main 715G3225 1 CBPCRNFABQAJ E750 750GLS190BT3ECN0AC
power 715G3350 1 2 PW8921EQIXSMTJ E750 750GLU190W1512N0AC
key 715G2944 3 KEPC8QK4J E750 750GLU190W1513N0AC

36
Service Guide Acer V193W

Schematic Diagram Chapter 7

Main Board ---715G3225-1
DSUB_5V 2.INPUT 3.SCALER 4.PANEL INTERFACE
BIN+ PANEL_EN
BIN+ BIN- BIN+ PANEL_EN PANEL_EN
BIN- SOGI BIN-
DSUB_5V SOGI GIN+ SOGI T7P
GIN+ GIN- GIN+ T7P T7M T7P
GIN- RIN+ GIN- T7M TCLK1P T7M
RIN+ RIN- RIN+ TCLK1P TCLK1M TCLK1P
RIN- HSIN RIN- TCLK1M T6P TCLK1M
ESD_5V HSIN VSIN HSIN T6P T6M T6P
VSIN VSIN T6M T5P T6M
DDC_SDA T5P T5M T5P
DDC_SDA DDC_SCL DDC_SDA T5M T4P T5M
ESD_5V
DDC_SCL DDC_SCL T4P T4M T4P
+5V VGA_DET T4M T3P T4M
VGA_DET VGA_DET T3P T3M T3P
T3M T3M
+5V DDC_WP DDC_WP

INPUT T2P
T2P T2M T2P
T2M T1P T2M
T1P T1M T1P
T1M T0P T1M
T0P T0M T0P
T0M T0M

PANEL INTERFACE

5.POWER
DSUB_5V 5VCC +5V VCC3.3
VCC3.3
VCC3.3 Panel_ID# +5V
Panel_ID# Panel_ID#
+5V BL_ADJ VCC3.3
BL_ADJ BL_ADJ
5VCC BL_ON
BL_ON BL_ON +5V
DSUB_5V Volume#
ESD_5V Volume# Volume#
Mute# VCC1.8
Mute# Mute#

VCC1.8 ESD_5V VCC1.8

5VCC
VCC1.8
5VCC

POWER SCALER

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL

ACER Size A

絬隔瓜絪腹 G3225-1-X-X-3-090220 TPV MODEL B/V173,B/V193 Rev E

Key Component 1.0.COVER PCB NAME 715G3225-1
称爹
Date Wednesday , April 21, 2010 Sheet 3 of 7

37
Service Guide Acer V193W

Input part---CN101
FB102
R101 0402->0603
VGA_B+ 1 2 R104 C101
BIN+ 5
BEAD 100R 1/16W 5% 0.047uF

H_Sy nc R101 0R05 1/10W 5% R102 470R 1/16W 5% R107

HSIN 5
C117 75R 1/16W 5%
V_Sy nc R103 100R 1/16W 5%
VSIN 5 NC/5PF50V
VGA_B- R108 C105
BIN- 5
100R 1/16W 5% 0.047uF
C102 R106 C103
R105 22pF 33pF
2K2 1/16W 5% 2K2 1/16W 5%

R109 C106
SOGI 5
DSUB_5V 390 OHM 1/16W 1000pF

16
DSUB_5V 7
R110 100R 1/16W 5% 10 FB103
DSUB_SCL 15 5 VGA_PLUG R118 10K 1/16W 5%
5 DDC_SCL VGA_DET 5
9 DSUB_5V VGA_G+ 1 2 R111 C107
GIN+ 5
14 4 BEAD 100R 1/16W 5% 0.047uF

2
8 VGA_B-
13 3 VGA_B+ R112
R113 100R 1/16W 5% 7 VGA_G- ZD103 ZD104 C118 75R 1/16W 5%
DSUB_SDA 12 2 VGA_G+ RLZ5.6B RLZ5.6B
5 DDC_SDA NC/5PF50V
6 VGA_R-
11 1 VGA_R+ VGA_G- R114 C109

1
GIN- 5
100R 1/16W 5% 0.047uF
CN101
17

DB15

FB101

D-SUB NC pin connect to GND VGA_R+ 1 2 R115 C110

RIN+ 5
BEAD 100R 1/16W 5% 0.047uF

R116
C119 75R 1/16W 5%
NC/5PF50V
VGA_R- R117 C113
RIN- 5
100R 1/16W 5% 0.047uF

ESD_5V
U102
1 6 VGA_G+
2 I/O1 I/O4 5
GNDVDD ESD_5V 7
VGA_B+ 3 4 VGA_R+ +5V DSUB_5V
I/O2 I/O3
5,6,7 +5V
AZC099-04S C114

1
NC

D101
NC/BAV70
ESD_5V
U103

3
DSUB_SDA 1 6 H_Sy nc R119
2 I/O1 I/O4 5 NC
DSUB_SCL 3 GNDVDD 4 V_Sy nc R120
I/O2 I/O3 NC R121 U101 C116
C115 NC 8 1 NC
AZC099-04S VCC A0
NC 7 2
DSUB_SCL 6 WP A1 3
DSUB_SDA 5 SCL A2 4
SDA VSS
5 DD C_WP
NC/M24C02-RMN6TP

TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL

ACER Size B

絬隔瓜絪腹 G3225-1-X-X-3-090220 TPV MODEL B/V173,B/V193 Rev E

Key Component 1.0.COVER PCB NAME 715G3225-1
称爹
Date Thursday , February 19, 2009 Sheet 4 of 7

38
Service Guide Acer V193W

Power part---5V/3.3V/1.8V
U701
AP1117D33L-13

ADJ(GND)
ESD_5V

VOUT
VIN
DSUB_5V
4 ESD_5V

D702

3
2
1
DSUB_5V 4

1
D703
+5V NC TO252
CN404 BAV99 5VCC
U702
4,5,6 +5V 5VCC
9 NC/AME8810-AEGTZ 0.6A/3.3V
8 3 2

3
7 D701 SM240A VIN VOUT(heat sink)

GND
5VCC 5
6
VCC3.3

4
5 BKLT-VBRI
4 BKLT-EN +5V
3 C_PANEL_INDEX

4
2 Volume
VCC3.3 5
1 Mute + C710
R701 100UF25V C701
10K 1/16W 5% 0.1UF 16V SOT223
CONN + C702 C703
100UF25V 0.1UF 16V
R702 0R05 1/16W R703 100R 1/16W 5%
Volume# 5
C708
NC/1uF 10V

+5V VCC3.3
VCC3.3 U703
NC/AP1117D18LA

ADJ(GND)
VOUT
VIN
R704 R706 R707
1K 1/16W 5% 4K7 1/16W 5% NC

3
2
1
BKLT-VBRI R705 100R 1/16W 5% MuteR708 100R 1/16W 5%
BL_ADJ 5 Mute# 5
VCC3.3
TO252 VCC1.8

U704
3 2
VI VO VCC1.8 5

GND

4
+5V + C704 C705 C706 + C707

4
NC/100UF25V NC/0.1UF 16V NC/0.1UF 16V NC/100UF25V
VCC3.3
R709 +5V VCC3.3
10K 1/16W 5%
SOT223
BKLT-EN R710
10K 1/16W 5%
R712 R713
NC NC

R711 22K 1/16W 5%

BL_ON 5
C709
0.1UF 16V Q406 C_PANEL_INDEX
Panel_ID# 5
2N3904S-RTK/PS
R714
NC
TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL ACER Size B

絬隔瓜絪腹 TPV MODEL B/V173,B/V193 Rev E

G3225-1-X-X-3-090220
Key Component 1.0.COVER PCB NAME 715G3225-1
称爹
Date Thursday , February 19, 2009 Sheet 7 of 7

39
Service Guide Acer V193W

Scalar part ----U401/U402

FB404
VCC3.3 120 OHM DVDD
VCC3.3

C451
C450 C430
C431 ADC_3.3 ADC_1.8 CVDD_3.3 CVDD_1.8 10UF6.3V
0.1UF 16V NC 4.7uF/16V
DVDD

11
12

25

26
U401

2
ADC_2.3

ADC_1.8

CVDD_2.3

CVDD_1.8
DVDD_BIAS
DVDD
4 49
4 BIN+ BIN1+ T0M T0M 6
5 48
4 BIN- BIN1- T0P T0P 6
6 47
4 SOGI SOG1I T1M T1M 6 7 VCC1.8
7 46 FB403
4 GIN+ GIN1+ T1P T1P 6
8 45 NC/300OHM ADC_1.8
4 GIN- GIN1- T2M T2M 6
9 44
4 RIN+ RIN1+ T2P T2P 6
10 43
4 RIN- RIN1- TCLK1M TCLK1M 6
42
TCLK1P TCLK1P 6
41
T3M T3M 6
14 40 C442 C406
4 HSIN HSY NCI1 T3P T3P 6
15 39 4.7uF/16V 0.1UF 16V
4 VSIN VSY NCI1 T4M T4M 6
38 C0805
T4P T4P 6
37
5VCC T5M T5M 6
36
T5P T5P 6 CVDD_1.8
35 FB406
VCC3.3 T6M T6M 6
34 NC/300OHM
7 5VCC T6P T6P 6

4K7 1/16W 5%

4K7 1/16W 5%
R422

R423
33
T7M T7M 6
32
T7P T7P 6
R408 10K 1/16W 5% R405 100R 1/16W 5% WP
R452 100R 1/16W 5% SPI_SO
R449 100R 1/16W 5% SPI_CE 52
PWMB* DDC_WP 4
C408 29 C443 C407
0.22uF16V PWMA* BL_ADJ 7
U402 NT68167FG/D 4.7uF/16V 0.1UF 16V
1 8 17 C0805
CE# VDD 4 DDC_SDA PB5*/DDC_SDA*/TX
2 7 16
3 SO HOLD# 6 R450 100R 1/16W 5% SPI_CK
4 DDC_SCL PB4*/DDC_SCL*/RX NT68167
4 WP# SCK 5 R451 100R 1/16W 5% SPI_SI
GND SI
SST25VF010A-33-4C-SAE

SPI_CE 62
SPI_SI 61 SPI_CE 53 VCC3.3 FB407
SPI_SI PA7*/PWM9* Volume# 7
SPI_SO
SPI_CK
60
59 SPI_SO
SPI_CLK Novatak PA6*/PWM8*
PA5*/PWM7*
PA4*/PWM6*
54
28
27
EE_WP
Mute# 7

Panel_ID# 7
300OHM ADC_3.3

57 WP
VCC3.3 PA3/PWM5 58 R414 22K 1/ 16W 5% LEDB
51 PA2/PWM4 21 R410 22K 1/16W 5% LEDO C439 C433
4 VGA_DET P35 PA1/PWM3
POWER_KEY # R419 1K 1/16W 5% 19 20 2.2uF/16V 0.1UF 16V
P34 PA0/PWM2 PANEL_EN 6
MSCL R463 NC/100R 1/16W 5%31 C0603
VCC3.3 P31/TXD
NC/4K7 1/16W 5%

NC/4K7 1/16W 5%

NC/10K 1/16W 5%

MSDA R464 NC/100R 1/16W 5%30

R417 P30/RXD
10K 1/16W 5% FB405
C429 18 300OHM CVDD_3.3
U403 NC/0.22uF16V RSTB 55 5V_DET
PB3/ADC3
R453

R454

R455

8 1 C401 63 56
VCC A0 OSCI PB2/ADC2 BL_ON 7

2
EE_WP 7 2 C411 47pF 23 KEY 1
MSCL 6 WP A1 3 0.1UF 16V PB1/ADC1 22 KEY 2
MSDA 5 SCL A2 4 X401 R462 PB0/ADC0 C445 + C444 C410
SDA GND 12MHz 1M 1/16W 5% 0.1uF/16V 0.1UF 16V

MGND
DGND
DGND
AGND
NC/M24C16 64 100UF25V

1
C412 47pF R429 0R05 1/16W OSCO

For LG A only model;, USE 24C04

13
24
50
3
CN401 +5V

1 key 3 R403 NC/2K2 1/16W 5%

+5V 4,6,7
2 key 4 R404 NC/2K2 1/16W 5%
3
4 VCC3.3 R406
5 DVDD
3.9K OHM 1/16W

3.9K OHM 1/16W

3.9K OHM 1/16W

6 10K 1/16W 5%
7 R409
7 VCC3.3
8 R401 NC/0R05 1/16W 20K OHM 1/16W
+5V 5V_DET

R465 R467 0R05 1/16W

NC/CONN 4K3 OHM 1/16W 5%
C409 0.1UF 16V
LEDB Q407
2N3906S-RTK/PS
R427

CN406 CN402
R428

R407

LED_GRN/BLUE
R466 470R 1/16W 5%
6 1 key 1 R416 100R 1/16W 5%
5 2 key 2 R411 100R 1/16W 5%
4 3 POWER_KEY #
3 4 LED_GRN/BLUE
2 5 LED_ORANGE DVDD
1 6 GND
C413

C414

C415

D404

C416

D405

C417

D406

R402 NC/0R05 1/16W

+5V
CONN NC/CONN
0.1UF 16V

0.1UF 16V

0.1UF 16V

0.1UF 16V

0.1UF 16V

R468 R470 0R05 1/16W

RLZ5.6B

RLZ5.6B

RLZ5.6B

4K3 1/16W 5%

LEDO Q408
2N3906S-RTK/PS
LED_ORANGE
R469 100R 1/10W 5%
CN407 CN408

7 1
6 2
5 3
4 4
3 5
2 6 GND
1 7
TPV ( Top Victory Electronics Co . , Ltd. ) OEM MODEL
ACER Size C
FB409
VCC3.3 B/V173,B/V193
NC/CONN NC/CONN TOUCH_PANEL 1 2 絬隔瓜絪腹 G3225-1-X-X-3-090220 TPV MODEL Rev E
NC/BEAD Key Component 1.0.COVER PCB NAME 715G3225-1
D402 NC/RLZ5.6B

C404 NC/0.1UF 16V

称爹
Date Thursday , February 19, 2009 Sheet 5 of 7

40
Service Guide Acer V193W

LVDS out part---CN403

CN403

CN405 1
2
PANEL_VCC 1 2 3
3 4 4

FB408
T0M 5 6 T0P 5
T1M 7 8 T1P 6
T2M 9 10 T2P 7
TCLK1M 11 12 TCLK1P T7P 8
5 T7P
T3M 13 14 T3P T7M 9
5 T7M
T4M 15 16 T4P TCLK1P 10
5 TCLK1P
T5M 17 18 T5P TCLK1M 11
5 TCLK1M

120 OHM
T6M 19 20 T6P T6P 12
5 T6P
TCLK1M 21 22 TCLK1P T6M 13
5 T6M
T7M 23 24 T7P 14
25 26 T5P 15
5 T5P
27 28 T5M 16
5 T5M
29 30 17

C449

R421

R434

C420
T4P 18
5 T4P
T4M 19
5 T4M
+ NC/CONN T3P 20
5 T3P
T3M 21
5 T3M

100UF25V
TCLK1P 22

0.1UF 16V
R1206 220 OHM 1/4W

R1206 220 OHM 1/4W

TCLK1M 23
24
T2P 25
5 T2P
T2M 26
5 T2M
T1P 27
5 T1P
T1M 28
5 T1M
T0P 29
5 T0P
T0M 30
5 T0M

CONN
PANEL_VCC
+5V
3D

5
6
7
8
R433 1 2
10K 1/16W 5% Q403 G S

D
D
D
D
NC/AO4411 AO3401L
Q405
R436 56K 1/16W 5%
AO3401

G
S
S
S
R418 C419

4
3
2
1
NC 0.22uF16V
R435 22K 1/16W 5% Q404
5 PANEL_EN
2N3904S-RTK/PS +5V

R415
4K7 1/16W 5% C441 C421 R420
0.1UF 16V 1uF/16V 10K 1/16W 5%

ACER A
T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size

絬隔瓜絪腹 G3225-1-X-X-3-090220 TPV MODEL B/V173,B/V193 Rev E

Key Component 1.0.COVER PCB NAME 715G3225-1
称爹
Date Thursday , February 19, 2009 Sheet 6 of 7

41
Service Guide Acer V193W

Power board---715G3350-1-2
R918
100 OHM 1/4W
FB902
R919 C912 C911 L904
100 OHM 1/4W +14V
1 2 1.1uH

2
0.0022uF 0.0022uF
BEAD R920
1

100 OHM 1/4W R941

! C905
R905 470 OHM 2W
ZD902
MTZJ T-72 18B
+

R951 0R05 1/4W R908

100uF/450V + +
6.8MOHM 1% 1/4W 100K 2W
+ C906 C917 C918

1
3 2 T901 D906

2
680uF/25V 680uF/25V
1.5NF/2KV Y5P +-10% 080GL17T 39N1P R943
1 3
BD901 ! C938
1500pF/1KV
Q903
PMBS3904
470OHM 1/8W
-

4 9 Y G868C15R
KBP208G R944 R952 R906

2
0 OHM +-5% 1/8W 6.8MOHM 1% 1/4W
4

C932 R939
100KOHM 1/4W D900 5 7 1K OHM
FR107 0.001uF
R935 C929
6 11 C931 F903

1
C902 C901 4 100 OHM 1/4W
0.0022uF 0.0022uF L903
0.001uF/250V 10 R961
0.001uF/250V D901 +5V
R909
100 OHM 1/4W 1.1uH
+ + FUSE 5A 250V
PS102R 5.1 OHM 1/4W 6 C940
! ! R907
C907 +
C908
1 8
R962 100 OHM 1/4W
C939 1000uF/16V
C915 +

22uF/50V D907 1000uF/16V 470UF M 16V

100KOHM 1/4W
1UF K 50V R940

2
3 12 NC(56K)
FMA09N65GX Q901 D905
SP1060

2
R953 NC R924
6.8MOHM 1% 1/4W D903 1N4148 1 C910
100 PF
! 1 3 150R 1/8W 5% ZD922
ZD921
! C904
R910 NC GDZJ5.1B
8

3
IC901 10R 1/4W

1
HV

OUT
NC

VCC

NC R927

1
R925
FAN6752MY R938 ! IC903 4.7K 1/8W
D915 D916
10K 1% 1/8W
COMP

FB901 PC123X2Y FZOF NC 1N4148

GND

10K 1/8W BEAD

CS
RT
1

2
L901

2
1

! 30mH
R912 C924
0.1uF
820 OHM 1/4W
2

R926 R942
C909 1K +-1% 1/8W
100pF R914 1K +-1% 1/8W
0.33 OHM +-5% IC904
KIA431A-AT/P
C903
! R954 C941

1UF K 25V X7R R930

220KOHM CN902 9.1K +-1% 1/8W
0.33UF +-10%

! ! ! C928
1NF J 50V X7R
14
13
R901 R902 R903
12
USB_CTRL
11
C921 +14V 10
0.0047UF/400V 9
1M 1/4W 1 M 1/4W 1M 1/4W 8
7
+5V
6
5
NC
! DIM
ON/OFF
4
3
2
1

VAR901 GND1 VOL

! NR901 ! NC
HS601
Q90G6258 2(U601)
MUTE
1
10/5A SW901
1 C916 C930
1
t 2 0.1uF
1

C913 C914 NC 2 0.1uF HARNESS

680pF
2

680pF

HS801 HS903
Q90G6274 2(D906) Q85G0002 1

F901 1 1
2.5A 250V 2 2

!
3

2 1

HS3 HS4
CN901 Q90G6263 3(Q901) Q90G6241 1 GP(D905)
T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL ACER 22'' W 2 Lamp Size A3
SOCKET
1 1 絬隔瓜絪腹 G3350-2B-2-X-12-091028 TPV MODEL PWPC9C21EQNN Rev C
2 2
Key Component 01.COVER PCB NAME 715G3350-2B-2
称爹 <称爹>
Date Monday , February 01, 2010 Sheet 1 of 4

42
Service Guide Acer V193W

Inverter part
CN801

1
+14V
2
C824
C802 + 0.1uF D810 C842
R857 R819 1uF/25V CONN
3.6K 1/8W 470UF +-20% 25V R817 R821
33R 1/8W 5% NC
10K 1/8W 5% 1K 1/8W 5%
Q801 Q802 2
R823
PMBS3904 4 5
3.6K 1/8W 3 G2 D2 6 C838 C819 3
Q808 2 S2 D2 7 1500PF50V T801 2200pF50V
PDTA144WK 1 G1 D1 8 1 8 DN
080GL24T 21 1
Q805 R839 S1 D1 D801
PDTC144WK Q804 APM9948K R856 2 R801 BAV99
33R 1/8W 5%

2
PMBS3906 15 OHM 1/4W C801 1.5K +-1% 1/8W
ON/OFF 18pF/6KV
1 4
3
C807
0.1uF 5 C808

3
CN802
D811 18pF/6KV
NC R855 6 7 1
Q811 15 OHM 1/4W 2
PMBS3904
C843
CONN
1uF/25V
R828 R822
R850 10K 1/8W 5% 1K 1/8W 5%
C839 2
1500PF50V
33R 1/8W 5%
3
Q812 C823

2
PMBS3906 2200pF50V 1
DIM
1 D802
R814 BAV99
1.5K 1% 1/8W

3
R827
1K 1/8W 5%

1
D805

B
BAW56

C
Q806
PMBS3904

3
R853

68K 1/8W 5%

R813
R808 10K+-1% 1/8W
D817 10K+-1% 1/8W
1N4148
2
.
9
V

Q810
RK7002

R811 D809
2K7 1/8W 1%
1N4148

R841

68K 1/8W 5%

R802
R851 C806
R829
75K 1/8W 1% 0.0033uF/16V
9K1 1/8W 1%
33R 1/8W 5%

R825

33R 1/8W 5%

C822 R832 R806

1uF/25V 10K +-1% 1/8W 68K 1/8W
IC801 TL494IDR D814
1 16
2
V
2 1IN+ 2IN+ 15
D812 1IN- 2IN- 1N4148
3 14 R818 R837
4 FEEDBACK REF 13 1K 1/8W 5%
5 DTC OUTPUT CTRL 12 47K 1/8W 5%
6 CT VCC 11
LL4148WP 7 RT C2 10
8 GND E2 9
C1 E1

2
.
5
V
~
4
.
5
V
C821 Q813
33NF50V PMBS3904

O
p
e
n
L
a
m
p
:
5
V

0
.
1
V

O
p
e
n
L
a
m
p
:
1
V
R861
R854
510K 1/8W

4
.
3
V
R820 R833 68K 1/8W 5% Q809

O
p
e
n
L
a
m
p
:
0
.
5
6
V
10K +-1% 1/8W R807 R803 RK7002
47K 1/8W 5% R810 Q807 1M 1/8W 5%
47K 1/8W
47K +-1% 1/8W PMBS3904
C825
C820 0.1uF
R824
R831 220pF R826
1K 1/8W
2.4K +-1% 1/8W 1K 1/8W C834 R835
C845 R862 0.01uF NC
2.2uF/25V 1M 1/8W 5%

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL ACER 22'' W 2 Lamp Size Custom

絬隔瓜絪腹 G3350-2B-2-X-12-091028 TPV MODEL PWPC9C21EQNN Rev C

Key Component 01.COVER PCB NAME 715G3350-2B-2
称爹 <称爹>
Date Wednesday , April 21, 2010 Sheet 1 of 4

43
Service Guide Acer V193W

Key board--- 715G2944-3

ZD001 UDZSNP5.6B
2 1
add ZD001 and ZD002 for ESD solution
LED001 LED

4 2

3 1

2 1
CN001
ZD002 UDZSNP5.6B

1 LBADC1 R001 2K OHM 1/16W

2 LBADC2 LED_BLUE#
3 POWER_Key LED_RED#
4 LED_BLUE#
5 LED_RED#
6
R002 2K OHM 1/16W
C001 C002 C003 C004 C005
NC NC NC NC NC
CONN

R003

1K 1/16W 5%

POWER_Key
C007
MENU 1.1 V

C008

C006
LBADC1

VOL+
VOL-
ECOLOR

MENU
VOL- (GND) 0 V

AUTO

NC
NC

NC
VOL+ 1.1 V
LBADC2
AUTO 0.65 V 1 3 5 7 9 11
SW001
JB41-03521
ECOLOR(GND) 0 V

2 4 6 8 10 12

CN001

CONNECTOR ECOLOR AUTO MENU VOL- VOL+ POWER LED

T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL acer B and V key pad Size A4

絬隔瓜絪腹 G2944-E-X-X-1-080218 TPV MODEL acer Rev E

Key Component 02.KEY PCB NAME 715G2944-E
称爹 <称爹>
Date Wednesday , September 10, 2008 Sheet 2 of 2

44
Service Guide Acer V193W

PCB Layout Chapter 8

Main Board Layout

45
Service Guide Acer V193W

46
Service Guide Acer V193W

Power board Layout

47
Service Guide Acer V193W

48
Service Guide Acer V193W

Key board Layout

49