ST330CPbF Series

Vishay High Power Products

Phase Control Thyristors

(Hockey PUK Version), 720 A
FEATURES
• Center amplifying gate
• Metal case with ceramic insulator
• International standard case TO-200AB (E-PUK) RoHS
COMPLIANT
• Lead (Pb)-free
• Designed and qualified for industrial level

TO-200AB (E-PUK) TYPICAL APPLICATIONS

• DC motor controls
PRODUCT SUMMARY • Controlled DC power supplies
IT(AV) 720 A • AC controllers

MAJOR RATINGS AND CHARACTERISTICS

PARAMETER TEST CONDITIONS VALUES UNITS
720 A
IT(AV)
Ths 55 °C
1420 A
IT(RMS)
Ths 25 °C
50 Hz 9000
ITSM A
60 Hz 9420
50 Hz 405
I2 t kA2s
60 Hz 370
VDRM/VRRM 400 to 1600 V
tq Typical 100 µs
TJ - 40 to 125 °C

ELECTRICAL SPECIFICATIONS
VOLTAGE RATINGS
VDRM/VRRM, MAXIMUM REPETITIVE PEAK VRSM, MAXIMUM IDRM/IRRM MAXIMUM
VOLTAGE
TYPE NUMBER AND OFF-STATE VOLTAGE NON-REPETITIVE PEAK VOLTAGE AT TJ = TJ MAXIMUM
CODE
V V mA

04 400 500
08 800 900
ST330C..C 12 1200 1300 50
14 1400 1500
16 1600 1700

Document Number: 94407 For technical questions, contact: [email protected] www.vishay.com

Revision: 11-Aug-08 1
ST330CPbF Series
Vishay High Power Products Phase Control Thyristors
(Hockey PUK Version), 720 A

ABSOLUTE MAXIMUM RATINGS

PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum average on-state current 180° conduction, half sine wave 720 (350) A
IT(AV)
at heatsink temperature double side (single side) cooled 55 (75) °C
Maximum RMS on-state current IT(RMS) DC at 25 °C heatsink temperature double side cooled 1420
t = 10 ms No voltage 9000
Maximum peak, one-cycle t = 8.3 ms reapplied 9420 A
ITSM
non-repetitive surge current t = 10 ms 100 % VRRM 7570
t = 8.3 ms reapplied Sinusoidal half wave, 7920
t = 10 ms No voltage initial TJ = TJ maximum 405
t = 8.3 ms reapplied 370
Maximum I2t for fusing I2 t kA2s
t = 10 ms 100 % VRRM 287
t = 8.3 ms reapplied 262
Maximum I2√t for fusing I2√t t = 0.1 to 10 ms, no voltage reapplied 4050 kA2√s
Low level value of threshold voltage VT(TO)1 (16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum 0.91
V
High level value of threshold voltage VT(TO)2 (I > π x IT(AV)), TJ = TJ maximum 0.92
Low level value of on-state slope resistance rt1 (16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum 0.58
mΩ
High level value of on-state slope resistance rt2 (I > π x IT(AV)), TJ = TJ maximum 0.57
Maximum on-state voltage VTM Ipk = 1810 A, TJ = TJ maximum, tp = 10 ms sine pulse 1.96 V
Maximum holding current IH 600
TJ = 25 °C, anode supply 12 V resistive load mA
Typical latching current IL 1000

SWITCHING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum non-repetitive rate of Gate drive 20 V, 20 Ω, tr ≤ 1 µs
dI/dt 1000 A/µs
rise of turned-on current TJ = TJ maximum, anode voltage ≤ 80 % VDRM
Gate current 1 A, dIg/dt = 1 A/µs
Typical delay time td 1.0
Vd = 0.67 % VDRM, TJ = 25 °C
µs
ITM = 550 A, TJ = TJ maximum, dI/dt = 40 A/µs,
Typical turn-off time tq 100
VR = 50 V, dV/dt = 20 V/µs, gate 0 V 100 Ω, tp = 500 µs

BLOCKING
PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum critical rate of rise of
dV/dt TJ = TJ maximum linear to 80 % rated VDRM 500 V/µs
off-state voltage
Maximum peak reverse and IRRM,
TJ = TJ maximum, rated VDRM/VRRM applied 50 mA
off-state leakage current IDRM

www.vishay.com For technical questions, contact: [email protected] Document Number: 94407

2 Revision: 11-Aug-08
 ST330CPbF Series
Phase Control Thyristors Vishay High Power Products
(Hockey PUK Version), 720 A

TRIGGERING
VALUES
PARAMETER SYMBOL TEST CONDITIONS UNITS
TYP. MAX.
Maximum peak gate power PGM TJ = TJ maximum, tp ≤ 5 ms 10.0
W
Maximum average gate power PG(AV) TJ = TJ maximum, f = 50 Hz, d% = 50 2.0
Maximum peak positive gate current IGM TJ = TJ maximum, tp ≤ 5 ms 3.0 A
Maximum peak positive gate voltage + VGM 20
TJ = TJ maximum, tp ≤ 5 ms V
Maximum peak negative gate voltage - VGM 5.0
TJ = - 40 °C 200 -
DC gate current required to trigger IGT TJ = 25 °C 100 200 mA
Maximum required gate trigger/
TJ = 125 °C current/voltage are the lowest 50 -
TJ = - 40 °C value which will trigger all units 2.5 -
12 V anode to cathode applied
DC gate voltage required to trigger VGT TJ = 25 °C 1.8 3.0 V
TJ = 125 °C 1.1 -
Maximum gate current/voltage
DC gate current not to trigger IGD not to trigger is the maximum 10 mA
TJ = TJ maximum value which will not trigger any
DC gate voltage not to trigger VGD unit with rated VDRM anode to 0.25 V
cathode applied

THERMAL AND MECHANICAL SPECIFICATIONS

PARAMETER SYMBOL TEST CONDITIONS VALUES UNITS
Maximum operating junction temperature range TJ - 40 to 125
°C
Maximum storage temperature range TStg - 40 to 150
DC operation single side cooled 0.09
Maximum thermal resistance, junction to heatsink RthJ-hs
DC operation double side cooled 0.04
K/W
DC operation single side cooled 0.02
Maximum thermal resistance, case to heatsink RthC-hs
DC operation double side cooled 0.01
9800 N
Mounting force, ± 10 %
(1000) (kg)
Approximate weight 83 g
Case style See dimensions - link at the end of datasheet TO-200AB (E-PUK)

ΔRthJ-hs CONDUCTION
SINUSOIDAL CONDUCTION RECTANGULAR CONDUCTION
CONDUCTION ANGLE TEST CONDITIONS UNITS
SINGLE SIDE DOUBLE SIDE SINGLE SIDE DOUBLE SIDE
180° 0.012 0.011 0.008 0.007
120° 0.014 0.012 0.014 0.013
90° 0.017 0.015 0.019 0.017 TJ = TJ maximum K/W
60° 0.025 0.022 0.026 0.023
30° 0.043 0.036 0.043 0.037
Note
• The table above shows the increment of thermal resistance RthJ-hs when devices operate at different conduction angles than DC

Document Number: 94407 For technical questions, contact: [email protected] www.vishay.com

Revision: 11-Aug-08 3
ST330CPbF Series
Vishay High Power Products Phase Control Thyristors
(Hockey PUK Version), 720 A

Maximum Allowable Heatsink Temperature (°C)

Maximum Allowable Heatsink Temperature (°C)

130 130
ST330C..C Series ST330C..C Series
120 (Double Side Cooled)
(Single Side Cooled)
120 RthJ-hs (DC) = 0.09 K/ W 110 RthJ-hs (DC) = 0.04 K/ W
100
110 90
80 Conduction Period
Conduction Angle
100 70 30°
60 60°
30°
90 60° 50 90°
90°
40 120°
120°
180°
80 180° 30
20 DC
70 10
0 50 100 150 200 250 300 350 400 0 200 400 600 800 1000 1200 1400 1600

Average On-state Current (A) Average On-state Current (A)

Fig. 1 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics

Maximum Allowable Heatsink Temperature (°C)

Maximum Average On-state Power Loss (W)

130 1400
ST330C..C Series 180°
120 (Single Side Cooled)
1200 120°
110 R thJ-hs (DC) = 0.09 K/ W 90°
100 60°
1000 RMS Limit
30°
90
Conduction Period 800
80
70
600
60 Conduction Angle
50 400
40 60° ST330C..C Series
30° 90° 200
30 120° 180° TJ = 125°C
DC
20 0
0 100 200 300 400 500 600 700 800 900 0 100 200 300 400 500 600 700 800

Average On-state Current (A) Average On-state Current (A)

Fig. 2 - Current Ratings Characteristics Fig. 5 - On-State Power Loss Characteristics

Maximum Allowable Heatsink Temperature (°C)

Maximum Average On-state Power Loss (W)

130 1800
ST330C..C Series DC
120 (Double Side Cooled) 1600 180°
110 RthJ-hs (DC) = 0.04 K/ W 120°
1400 90°
100 60°
1200 30°
90
80 Conduction Angle 1000 RMSLimit
70 800
60 Conduction Period
600
50 30° 60°
90° 400
40 120° ST330C..C Series
180°
30 200 TJ = 125°C

20 0
0 200 400 600 800 1000 0 200 400 600 800 1000 1200

Average On-state Current (A) Average On-state Current (A)

Fig. 3 - Current Ratings Characteristics Fig. 6 - On-State Power Loss Characteristics

www.vishay.com For technical questions, contact: [email protected] Document Number: 94407

4 Revision: 11-Aug-08
 ST330CPbF Series
Phase Control Thyristors Vishay High Power Products
(Hockey PUK Version), 720 A

8000 9000

Peak Half Sine Wave On-state Current (A)

Peak Half Sine Wave On-state Current (A)

At Any Rated Load Condition And With Maximum Non Repetitive Surge Current
7500 Rated VRRM Applied Following Surge. 8500 Versus Pulse Train Duration. Control
Initial TJ = 125°C 8000 Of Conduc tion May Not Be Maintained.
7000 @60 Hz 0.0083 s Initial TJ = 125°C
@50 Hz 0.0100 s 7500
No Voltage Reapplied
6500 7000 Rated VRRM Reapplied
6000 6500

5500 6000
5500
5000
5000
4500
4500
ST330C..C Series ST330C..C Series
4000 4000
3500 3500
1 10 100 0.01 0.1 1
Number Of Equal Amplitude Half Cycle Current Pulses (N) Pulse Train Duration (s)

Fig. 7 - Maximum Non-Repetitive Surge Current Fig. 8 - Maximum Non-Repetitive Surge Current
Single and Double Side Cooled Single and Double Side Cooled

10000

TJ = 25°C
Instantaneous On-state Current (A)

TJ = 125°C

1000

ST330C..C Series

100
0 1 2 3 4 5 6 7
Instantaneous On-state Voltage (V)

Fig. 9 - On-State Voltage Drop Characteristics

0.1
Transient Thermal Impedance Z thJ-hs (K/ W)

Steady State Value

RthJ-hs = 0.09 K/ W
(Single Side Cooled)
R thJ-hs = 0.04 K/ W
(Double Side Cooled)
(DC Operation)
0.01

ST330C..C Series

0.001
0.001 0.01 0.1 1 10
Square Wave Pulse Duration (s)

Fig. 10 - Thermal Impedance ZthJ-hs Characteristics

Document Number: 94407 For technical questions, contact: [email protected] www.vishay.com

Revision: 11-Aug-08 5
ST330CPbF Series
Vishay High Power Products Phase Control Thyristors
(Hockey PUK Version), 720 A

100
Rectangular gate pulse (1) PGM = 10W, tp = 4 ms
a) Recommended load line for (2) PGM = 20W, tp = 2 ms

Instantaneous Gate Voltage (V)

rated di/ dt : 20V, 10ohms; tr<=1 µs (3) PGM = 40W, tp = 1 ms
b) Recommended load line for (4) PGM = 60W, tp = 0.66 ms
<=30% rated di/ dt : 10V, 10ohms
10 tr<=1 µs (a)
(b)

Tj=-40 °C
Tj=25 °C
Tj=125 °C
1
(1) (2) (3) (4)
VGD
IGD
Device: ST330C..C Series Frequency Limited by PG(AV)
0.1
0.001 0.01 0.1 1 10 100
Instantaneous Gate Current (A)

Fig. 11 - Gate Characteristics

ORDERING INFORMATION TABLE

Device code ST 33 0 C 16 C 1 - PbF

1 2 3 4 5 6 7 8 9

1 - Thyristor
2 - Essential part number
3 - 0 = Converter grade
4 - C = Ceramic PUK
5 - Voltage code x 100 = VRRM (see Voltage Ratings table)
6 - C = PUK case TO-200AB (E-PUK)
7 - 0 = Eyelet terminals (gate and auxiliary cathode unsoldered leads)
1 = Fast-on terminals (gate and auxiliary cathode unsoldered leads)
2 = Eyelet terminals (gate and auxiliary cathode soldered leads)
3 = Fast-on terminals (gate and auxiliary cathode soldered leads)
8 - Critical dV/dt: None = 500 V/µs (standard selection)
L = 1000 V/µs (special selection)
9 - Lead (Pb)-free

LINKS TO RELATED DOCUMENTS

Dimensions http://www.vishay.com/doc?95075

www.vishay.com For technical questions, contact: [email protected] Document Number: 94407

6 Revision: 11-Aug-08
 Outline Dimensions
Vishay Semiconductors

TO-200AB (E-PUK)

DIMENSIONS in millimeters (inches)

Anode to gate
Creepage distance: 11.18 (0.44) minimum
Strike distance: 7.62 (0.30) minimum

25.3 (0.99)
DIA. MAX.
0.3 (0.01) MIN.

14.1/15.1
(0.56/0.59)

0.3 (0.01) MIN.

25.3 (0.99) Gate terminal for
DIA. MAX. 1.47 (0.06) DIA.
pin receptacle

40.5 (1.59) DIA. MAX.

2 holes 3.56 (0.14) x 1.83 (0.07) minimum deep

6.5 (0.26)

4.75 (0.19)

25° ± 5°

42 (1.65) MAX.

28 (1.10)

Quote between upper and lower pole pieces has to be considered after
application of mounting force (see thermal and mechanical specification)

Document Number: 95075 For technical questions, contact: [email protected] www.vishay.com

Revision: 01-Aug-07 1
 Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.

Revision: 12-Mar-12 1 Document Number: 91000

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Vishay:
ST330C12L0L ST330C16L0L ST330C16L1L ST330C12C0L ST330C12C1L ST330C14C0L ST330C14C1L
ST330C16C0L ST330C16C1L VS-ST330C08C0 VS-ST330C12C0 VS-ST330C12L0 VS-ST330C14C0 VS-
ST330C16C0 VS-ST330C14L1 VS-ST330C16L0 VS-ST330C04C0 VS-ST330C14L0 VS-ST330C08L0 VS-
ST330C04L1 VS-ST330C14C1 VS-ST330C16C1 VS-ST330C04C1 VS-ST330C04L0 VS-ST330C08C1 VS-
ST330C08L1 VS-ST330C12L1 VS-ST330C16L1 VS-ST330C12C1 VS-ST330C16C3