Structural Use of Timber

BRITISH STANDARD BS 5268-6.
2:2001
Incorporating
Corrigendum No. 1
Structural use of
timber —
Licensed Copy: Lee Jenny, na, Wed Aug 29 03:46:39 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
Part 6: Code of practice for timber

frame walls —
Section 6.2: Buildings other than

dwellings not exceeding four storeys
ICS 91.060.10; 91.080.20
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

BS 5268-6.2:2001
Committees responsible for this

British Standard
The preparation of this British Standard was entrusted by Technical

Committee B/525, Building and civil engineering structures, to Subcommittee
B/525/5, Structural use of timber, upon which the following bodies were
represented:
British Woodworking Federation

Construction User Group
Department of the Environment, Transport and the Regions
Health and Safety Executive
Institution of Civil Engineers
Institution of Structural Engineers
National House-Building Council
Trussed Rafter Association
Timber Research and Development Association
Timber Trade Federation
United Kingdom Forestry Products Association
This British Standard, having

been prepared under the
direction of the Building and
Civil Engineering Sector Policy
and Strategy Committee, was
published under the authority
of the Standards Policy and
Strategy Committee and comes
into effect on 15 August 2001
© BSI 31 January 2002

Amendments issued since publication
Amd No. Date Comments
The following BSI references 13630 31 January 2002 Indicated by a sideline

relate to the work on this British Corrigendum No. 1
Standard:
Committee reference B/525/5

Draft for comment 98/106653 DC
ISBN 0 580 33276 4

BS 5268-6.2:2001
Contents
Page
Committees responsible Inside front cover
Foreword ii
1 Scope 1
2 Normative references 1
3 Terms and definitions 2
4 Materials 3
5 Loading 4
6 Design of timber frame walls 7
7 Workmanship 17
Bibliography 19
Table 1 — Modification factor, K200 6
Table 2 — Basic racking resistances for a range of materials and
combinations of materials 8
Table 3 — Contribution of masonry cladding to racking resistance 16
© BSI 31 January 2002 i

BS 5268-6.2:2001
Foreword
This section of BS 5268 has been prepared by Subcommittee B/525/5, Structural

use of timber.
BS 5268 is published in the following parts and sections:
— Part 2: Code of practice for permissible stress design, materials and
workmanship;
— Part 3: Code of practice for trussed rafter roofs;

— Part 4: Fire resistance of timber structures;
— Section 4.1: Recommendations for calculating fire resistance of timber
members;
— Section 4.2: Recommendations for calculating fire resistance of timber stud
walls and joisted floor constructions;
— Part 5: Code of practice for the preservative treatment of structural timber;
— Part 6: Code of practice for timber frame walls;
— Section 6.1: Dwellings not exceeding four storeys;
— Section 6.2: Buildings other than dwellings not exceeding four storeys;
— Part 7: Recommendations for the calculation basis for span tables;
— Section 7.1: Domestic floor joists;
— Section 7.2: Joists for flat roofs;
— Section 7.3: Ceiling joists;
— Section 7.4: Ceiling binders;
— Section 7.5: Domestic rafters;
— Section 7.6: Purlins supporting rafters;
— Section 7.7: Purlins supporting sheeting or decking.
BS 5268-6.1 was first published in 1988 (with subsequent revisions) and covers
the design of timber frame walls in dwellings up to four storeys in height.
In recent years the demand for timber frame structures for building other than
dwellings has developed rapidly and it has been estimated that around 50 % of
the output of the timber frame manufacturing industry is produced for
non-domestic buildings.
This section of BS 5268 follows a similar methodology to BS 5268-6.1, but because
of the demand for greater storey heights in non-domestic buildings, it is based
upon an extensive range of tall wall panel racking tests carried out on wall panels
up to 4.8 m in height. It is essentially written for buildings other than dwellings,
but some of the information in respect of the performance of wall panels over
2.7 m in height may also be appropriate for use in the design of tall wall panels
in dwellings.
As a code of practice, this British Standard takes the form of guidance and
recommendations. It should not be quoted as if it were a specification and
particular care should be taken to ensure that claims of compliance are not
misleading.
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
pages 1 to 18, an inside back cover and a back cover.
The BSI copyright notice displayed in this document indicates when the
document was last issued.
Sidelining in this document indicates the most recent changes by amendment.
ii © BSI 31 January 2002

BS 5268-6.2:2001
1 Scope
This section of BS 5268 gives recommendations for the design, testing, fabrication and erection of timber
frame walls for buildings other than dwellings not exceeding four storeys in height and where the following
conditions apply.
a) The maximum overall height of any building is 15 m.
b) The maximum panel height in a single storey building is 6.2 m.
c) The maximum panel height in buildings of more than one storey is 4.8 m.
This section of BS 5268-6 gives recommendations for timber frame walls, with studs continuous in length
throughout the panel height, not exceeding 610 mm centre to centre and one or both faces of the studs being
partly or wholly connected to sheathing or lining. The design information contained in this section of
BS 5268 is principally intended to cover storey height panel construction. Much of the information is also
relevant to other forms of panel construction, for example, where studs are continuous through two or more
storeys.
All structural materials are assumed to be subject only to service classes 1 and 2, as defined in
BS 5268-2:1996.
The design information on the racking performance of tall wall panels (over 2.7 m in height), contained in
this section of BS 5268-6, may also be relevant to the design of tall wall panels in dwellings. The design
method described in this section of BS 5268-6 may be used in validating the racking performance of wall
panels over 2.7 m in height for use in dwellings in combination with designs in accordance with the
recommendations of BS 5268-6.1.
This section of BS 5268 covers only the structural design of timber frame walls. The following
constructional features may significantly affect the basis of the design, and they are drawn to the attention
of the designer:
a) susceptibility to weathering;
b) condensation control;
c) thermal insulation;
d) fire resistance;
e) sound insulation;
f) durability.
2 Normative references
The following normative documents contain provisions, which, through reference in this text, constitute
provisions of this part of this British Standard. For dated references, subsequent amendments to, or
revisions of, any of these publications do not apply. For undated references, the latest edition of the
publication applies.
BS 187, Specification for calcium silicate (sandlime and flintstone) bricks.
BS 1230-1, Gypsum plasterboard — Part 1: Specification for plasterboard excluding materials submitted to
secondary operations.
BS 3921, Specification for clay bricks.
BS 4551:1980, Methods of testing mortars, screeds and plasters.
BS 4729, Specification for dimensions of bricks of special shapes and sizes.
BS 5268-2:1996, Structural use of timber — Part 2: Code of practice for permissible stress design, materials
and workmanship.
BS 5268-3:1998, Structural use of timber — Part 3: Code of practice for trussed rafter roofs.
BS 5268-5:1989, Structural use of timber — Part 5: Code of practice for the preservative treatment of
structural timber.
BS 5268-6, Structural use of timber — Part 6: Code of practice for timber frame walls.
BS 5268-6.1:1996, Structural use of timber — Part 6: Code of practice for timber frame walls —
Section 6.1: Dwellings not exceeding four storeys.
© BSI 31 January 2002 1

BS 5268-6.2:2001
BS 5390, Code of practice for stone masonry.

BS 5628-1:1992, Code of practice for use of masonry — Part 1: Structural use of unreinforced masonry.
BS 5628-2:1985, Code of practice for use of masonry — Part 2: Structural use of reinforced and prestressed
masonry.
BS 5628-3, Code of practice for use of masonry — Part 3: Materials and components, design and
workmanship.
BS 6073-1, Precast concrete masonry units — Part 1: Specification for precast concrete masonry units.
BS 6100 (all parts), Glossary of building and civil engineering terms.
BS 6399-1, Loading for buildings — Part 1: Code of practice for dead and imposed loads.
BS 6399-2, Loading for buildings — Part 2: Code of practice for wind loads.
BS 6399-3, Loading for buildings — Part 3: Code of practice for imposed roof loads.
BS 6446, Specification for manufacture of glued structural components of timber and wood based panel
products.
BS 6457, Specification for reconstructed stone masonry units.
BS 6649, Specification for clay and calcium silicate modular bricks.
BS EN 300:1997, Oriented strand board (OSB) — Definitions, classification and specifications.
BS EN 312-5:1997, Particleboards — Specifications — Part 5: Requirements for load-bearing boards for use
in humid conditions.
BS EN 312-7:1997, Particleboards — Specifications — Part 7: Requirements for heavy duty load-bearing
boards for use in humid conditions.
BS EN 336, Structural timber — Coniferous and poplar — Sizes — Permissible deviations.
BS EN 385, Finger jointed structural timber — Performance requirements and minimum production
requirements.
BS EN 594:1996, Timber structures — Test methods — Racking strength and stiffness of timber frame wall
panels.
BS EN 622-2:1997, Fibreboards — Specifications — Part 2: Requirements for hardboards.
BS EN 622-3:1997, Fibreboards — Specifications — Part 3: Requirements for medium boards.
BS EN 622-4:1997, Fibreboards — Specifications — Part 4: Requirements for softboards.
BS EN 634-2:1997, Cement bonded particleboards — Specifications — Part 2: Requirements for OPC
bonded particle boards for use in dry, humid and exterior conditions.
DD ENV 1995-1-1:1994, Eurocode 5 — Design of timber structures — General rules and rules for buildings
(together with United Kingdom National Application Document).
3 Terms and definitions
For the purposes of this section of BS 5268 the following terms and definitions apply.
3.1
cripple stud
vertical member in a framed partition or wall that supports a lintel
3.2
racking resistance
ability of a partition or wall panel to resist horizontal wind forces in the plane of the panel
3.3
gable apex panel
wall panel forming the apex of a gable
2 © BSI 31 January 2002

BS 5268-6.2:2001
3.4
stud
vertical member in a framed partition or wall
3.5
timber frame wall
wall constructed of timber framing members, bracing and/or wall sheathing
3.6
wall lining
manufactured sheet or board used to line a wall or partition
3.7
wall panel
component that forms part of a timber frame wall
3.8
wall sheathing
sheet or board used as a bracing
4 Materials
4.1 General
The materials used should conform to the appropriate British Standards.
Reference should be made to BS 5268-5 for information on methods of wood preservation.
All sheathing and lining materials should be of a thickness and robustness so that damage during
manufacture, transport and erection is avoided.
4.2 Species of timber
All structural timber should be strength graded in accordance with the recommendations of BS 5268-2.
NOTE Any of the species of timber listed in BS 5268-2 may be used.
4.3 Sheathing materials

4.3.1 Plywood
The species and grades of plywood for sheathing should be one of those described in BS 5268-2.
4.3.2 Fibre building boards
Fibre building boards for use as structural sheathing should be one of the following types:
a) type HB.HLA2 tempered hardboard conforming to BS EN 622-2:1997;
b) type MBH.HLS1 or MBH.HLS2 medium board conforming to BS EN 622-3:1997;
c) impregnated softboard type SB.HLS conforming to BS EN 622-4:1997.
4.3.3 Wood chipboard
Wood chipboard sheathing should be type P5 conforming to BS EN 312-5:1997 or type P7 conforming
to BS EN 312-7:1997.
4.3.4 Oriented strand board
Oriented strand board for sheathing should be type OSB/3 or OSB/4 conforming to BS EN 300:1997.
4.3.5 Cement bonded particleboard
Cement bonded particleboard should be type OPC bonded conforming to BS EN 634-2:1997.

BS 5268-6.2:2001
4.3.6 Other sheathings

Where sheathings other than those described in 4.3.1, 4.3.2, 4.3.3, 4.3.4 and 4.3.5 are to be used they
should conform to the relevant British or European Standard.
The durability of any wall sheathing material with a view to its intended end use should be ensured.
4.4 Gypsum plasterboard
Where gypsum plasterboard is assumed to make a structural contribution in the design of a timber frame
wall, the plasterboard should be manufactured in accordance with BS 1230-1.
4.5 Adhesives
Adhesives used in the construction of timber frame wall panels should be of a type and quality suitable for
the conditions of use.
NOTE Further advice on suitable adhesives and the quality of workmanship is given in BS 5268-2 and BS 6446.
4.6 Fasteners
Structural fasteners should be corrosion resistant and should be compatible with any preservative
treatments used and any other metalwork with which they are in contact.
In the construction of panels and for fixing sheathing mild steel or stainless steel nails should be used, of
round head or D-head configuration, and the size to be used should be given in the design.
4.7 Masonry cladding
Where masonry cladding to be used for shielding the timber frame or to contribute to the racking resistance
of a timber frame wall it should be designed in accordance with the appropriate part of BS 5628 or BS 5390
for stone masonry and should be at least 100 mm thick and have a minimum density of 750 kg/m3.
5 Loading
5.1 General
Timber frame walls should be designed to carry the appropriate dead, imposed and wind loads given
in BS 6399-1, -2 and -3 and to transfer such loads to the foundation without undue distortion and
movement.
5.2 Wind loading
5.2.1 Distribution of wind load
Wind acting on a building induces external and internal pressures on the roof and walls, as described in
BS 6399-2. Both horizontal and vertical loads thus developed should be considered in the design of timber
frame walls.
NOTE The wind load is resisted primarily by transfer directly to the ground at the base of the wall and by the racking resistance of
timber frame supporting walls, the load having been transferred via the floor and ceiling diaphragms. Other non-specific factors
assisting in the resistance to wind loads are taken into account in the interaction factor given in 5.2.3.

BS 5268-6.2:2001
5.2.2 Wind loading on masonry clad timber frame walls

Where timber frame walls are clad by masonry and the following conditions are met, the external wind
loading transferred to the timber structure should be determined in accordance with 5.2.3.
a) The masonry walls should be constructed of:

— clay bricks conforming to BS 3921;
— concrete bricks conforming to BS 6073-1;
— calcium silicate bricks conforming to BS 187;
— clay and calcium silicate modular bricks conforming to BS 6649;
— concrete blocks conforming to BS 6073-1;
— reconstructed stone conforming to BS 6457;
— stone masonry conforming to BS 5390;
— bricks of special shapes and sizes conforming to BS 4729.
b) The mortar should conform to BS 5628-3 and be not lower than designation (iii) or conform to BS 5390
for stone masonry.
c) Masonry cladding should be connected to the timber frame with wall ties that have sufficient strength
and stiffness to transfer wind forces to the timber frame wall. The wall ties and tying pattern should also
ensure adequate stability and robustness of the masonry cladding.
NOTE In the absence of other guidance on wall tie spacing, designers are directed to DD 140-2, which gives characteristic tensile
and compressive forces for timber frame to masonry wall ties.
5.2.3 Wind load transferred to timber frame wall

In the case of buildings where storey heights do not exceed 3 m between floors or between floor and roof the
wind load used in calculating the racking load, overturning and sliding forces to be resisted by the timber
frame walls should be derived by multiplying the external wind load on the masonry cladding by the
modification factor, K200, appropriate to the height of building being considered (see Table 1).
For cases where storey heights exceed 3 m between floors or between floor and roof the modification factor,
K200, should be taken as 1.0.
NOTE In calculating the racking load, overturning and sliding forces, the wind load modification factor, K200, where applicable,
relates to the entire area of the shielded timber frame wall.

BS 5268-6.2:2001
Table 1 — Modification factor, K200

Height of Percentage of K200
building to wall occupied
eaves by openingsa
For masonry walls with For masonry walls with For masonry walls
buttresses or returns not buttresses or returns at one without buttresses or
less than 550 mm and not end of wall not less than returns or with buttresses
greater than 9 m centre to 550 mm, other end without or returns of less than
centreb buttresses or returns less 550 mmd
than 550 mm, wall length not
greater than 4.5 mc
<6 m 0 0.45 0.60 0.75
10 0.50 0.64 0.78
20 0.56 0.68 0.80
30 0.61 0.72 0.83
40 0.66 0.76 0.85
50 0.71 0.80 0.88
60 0.77 0.84 0.90
70 0.82 0.88 0.93
>70 1.00 1.00 1.00
>6 m and 0 0.50 0.68 0.85
<9 m 10 0.55 0.71 0.87
20 0.60 0.74 0.88
30 0.65 0.78 0.90
40 0.70 0.81 0.92
50 0.75 0.84 0.93
60 0.80 0.87 0.94
70 0.85 0.91 0.96
>70 1.00 1.00 1.00
Height of Percentage of For masonry walls with For masonry walls with For masonry walls
building to wall occupied buttresses or returns not buttresses or returns at one without buttresses or
eaves by openingsa less than 950 mm and not end of wall not less than returns or with buttresses
greater than 9 m centre to 950 mm, other end without or returns of less than
centreb buttresses or returns less 950 mmd
than 950 mm, wall length not
greater than 4.5 mc
>9 m and 0 0.60 0.74 0.88
<12 m 10 0.64 0.77 0.89
20 0.69 0.80 0.91
30 0.73 0.83 0.93
40 0.77 0.86 0.95
50 0.81 0.89 0.96
60 0.86 0.92 0.98
70 0.90 0.95 1.00
>70 1.00 1.00 1.00
NOTE 1 Values for intermediate percentages of wall occupied by openings may be obtained by linear interpolation.
NOTE 2 The K200 factors and support conditions (where relevant) should be selected on the basis of the maximum height of the
wall under consideration and be applied to the whole wall.
NOTE 3 For walls longer than 9 m, the values of K200 given in column 3 may be used provided additional buttresses or returns are
added to the masonry wall at a maximum centre to centre spacing of 9 m.
a In calculating the percentage of wall occupied by openings, the height of the wall should be taken as the height to the eaves.
b Values of K200 to be used where a masonry wall is supported at both ends by adequate masonry buttresses or returns.
c Values of K200 to be used where a wall, which otherwise has adequate buttresses or returns, incorporates a vertical movement
joint (i.e. the wall has the required buttress or return at one end, but is not adequately supported at the other).
d Values of K200 to be used where a wall has no masonry returns or buttresses or has inadequate supports at its ends.

BS 5268-6.2:2001
6 Design of timber frame walls

6.1 Structural design
The structural design of a timber frame wall should be carried out by any one or combination of the
following methods:
a) using the laws of structural mechanics (using data given in BS 5268-2);
b) in accordance with the method described in this clause;
c) load testing of full-size wall units in accordance with BS EN 594 and the results interpreted in
accordance with BS 5268-6.1, clause 5.
NOTE Attention is drawn to the importance of checking the overall stability of the building.
6.2 Permissible stresses

The grade stresses for timber, plywood, tempered hardboard and wood chipboard used in the design should
be as given in BS 5268-2:1996 or DD ENV 1995-1-1:1994, as appropriate.
A timber frame external wall should be designed using stresses for service class 2 as described in
BS 5268-2:1996 or DD ENV 1995-1-1:1994, as appropriate.
6.3 Composite action with other materials
Where a timber frame wall is designed to act compositely with other materials such as cladding, sheathing
or lining, the appropriate composite action should be established by test or by calculation or, in the case of
racking resistance, on the basis of the information given in Table 2.
NOTE Where composite action is not assumed but the other materials are partly self-supporting and are capable of carrying a share
of the horizontal wind loading, the timber frame wall can be designed to carry a correspondingly reduced horizontal wind loading.
6.4 Overall stability

The factor of safety against overturning or sliding of a building with timber frame walls should be not less
than 1.20 when subjected to dead loading, zero imposed loading and horizontal and vertical components of
wind loading acting simultaneously.
Designers should assure themselves of the resistance of the structure to sliding under the action of
horizontal wind forces. Where applicable, shear fixings and frictional resistance should be taken into
account when considering the resistance to sliding.
NOTE Attention is drawn to the need to consider the stability of the building during construction.
6.5 Horizontal diaphragms

When lateral loading acts on vertically spanning stud walls, horizontal diaphragms are essential to
transfer such loads to other walls capable of providing racking resistance. A check that adequate
diaphragm action is provided should be carried out.
Some horizontal diaphragms have sufficient strength and stiffness to transmit lateral forces to supporting
walls without the need for further design consideration or calculations, provided that, in the case of
intermediate floors or flat roofs, a wood-based deck, sub-deck or lining is fixed directly to the upper or lower
faces of the joists, and in the case of pitched roofs, a plasterboard ceiling is combined with roof bracing as
recommended in BS 5268-3.
Such diaphragms should have no horizontal dimension exceeding 12 m between supporting walls and a
length to width ratio, l/w, not greater than 2, where l is the greatest horizontal dimension of the diaphragm
and w is the smallest horizontal dimension.

BS 5268-6.2:2001
Table 2 — Basic racking resistances for a range of materials and combinations of materials
Primary board material Fixing Racking Additional contribution of
resistance secondary board on timber
frame wall
Category 2 or 3 Category 1
materials material
kN/m kN/m kN/m
Category 1 materials: 3.00 mm diameter wire nails at 1.68 0.28 0.84

— 9.5 mm plywood; least 50 mm long, maximum
— 9.0 mm medium board; spacing 150 mm on perimeter,
300 mm internal
— 12.0 mm chipboard
(type P5 or P7);
— 6.0 mm tempered
hardboarda;
— 9.0 mm OSB (type OSB/3).
Category 2 materials: 3.00 mm diameter wire nails at 0.90 0.45 1.06
— 12.5 mm bitumen least 50 mm long, maximum
impregnated insulation spacing 75 mm on perimeter,
board. 150 mm internal
Category 3 materials: 2.65 mm diameter plasterboard 0.90 0.45 1.06
— 12.5 mm plasterboard. nails at least 40 mm long,
maximum spacing 150 mm
NOTE 1 Timber members in external and internal wall panels should be not less than 38 mm thick with a minimum width of
72 mm or 0.026 times the panel height in millimetres (mm), whichever is the greater. All members to be rectangular section with
linings fixed to the narrower face, with ends cut square and assembled in accordance with the relevant recommendations of
clause 7.
NOTE 2 In the specific case of internal wall panels, smaller timber members may be used but in this case should be not less than
38 mm thick with a minimum width of 63 mm or 0.023 times the panel height in millimetres (mm) whichever is the greater, and in
such cases all values for basic racking resistance given in this table should be reduced by 15 %.
NOTE 3 Studs should be spaced at centres not exceeding 610 mm.
NOTE 4 Board edges should be backed by, and nailed to timber framing.
NOTE 5 Studs should be of species and stress grade satisfying strength class C16 or better (as defined in BS 5268-2:1996).
NOTE 6 The additional contribution from a secondary layer of category 1, 2 or 3 materials should only be included once in the
determination of basic racking resistance, no matter how many additional layers may be fixed to the wall panel.
NOTE 7 The values given in Table 2 together with the modification factors in 6.8 and 6.9 assume that the wall under consideration
is adequately fixed to ensure resistance to sliding and overturning.
NOTE 8 Where a secondary board is fixed on the same side of a wall as the primary sheathing then the nail lengths given in the
table should be increased to take account of the additional thickness.
a For wall panels in excess of 2.7 m in height the thickness of tempered hardboard should be increased to 9 mm.

BS 5268-6.2:2001
6.6 Design of wall studs

6.6.1 General
Wall studs should be designed as compression members, subject where appropriate, to bending in a
direction perpendicular to the plane of the wall, in accordance with BS 5268-2.

6.6.2 Lateral restraint
Lateral restraint in the plane of the wall should be provided by noggings, sheathing or plasterboard lining.
In calculating the slenderness ratio of studs sheathed with any of the board materials described in Table 2
and fixed to the studs as recommended in Table 2, the effective length should be assumed to be 0.85 times
the actual length when considering buckling out of the plane of the wall.
Solid rectangular studs in timber frame walls covered on one or both sides with any of the board materials
described in Table 2 and fixed as recommended in Table 2, should be assumed to be fully restrained
laterally in the plane of the wall.
6.6.3 Interaction with sheathing
Where advantage is taken of the interaction between the studs and sheathing in resisting compression and
bending or in reducing deflection, account should be taken of the relative stiffness of the materials acting
compositely and of the slip under load of mechanical fastenings.
6.6.4 Eccentricity of load
Consideration should be given to eccentricity of load.
Loads transmitted from trusses, joists, lintels, beams or attached claddings bearing on the timber frame
wall should be considered to act at the centroid of the bearing area.
Bending moments due to eccentric loads applied at the top of a timber frame wall should be taken as zero
at the base of the wall.
Where studs are continuous through more than one storey, bending moments applied at an intermediate
floor should be divided between the upper and lower storeys in proportion to the stiffness of the studs.
NOTE For studs of constant cross-section throughout their height, the bending moment may be divided equally between upper and
lower storeys provided the ratio of storey heights does not exceed 1.5.
6.6.5 Lateral deflection

Designers should assure themselves about the serviceability of external walls subject to horizontal wind
forces.
The calculation of the out of plane lateral deflection of studs in wall panels of composite walls is complex
and outside the scope of this standard. However, calculation of the out of plane deflection of wall studs
alone, ignoring the contribution of cladding materials, gives an indication of the robustness of the wall
panel and its likely performance within a composite wall, even though this will give a conservative estimate
of the actual deflection of the wall construction. Such calculations should be carried out in accordance with
BS 5268-2.
In calculating deflection, under the action of wind loads, the assumptions made in respect of end fixity, as
implied in 6.6.2, should be taken into account. For the purpose of this calculation, vertical load should be
ignored.
6.6.6 Cripple studs
Cripple studs supporting lintels or beams should be considered to act compositely with the adjacent
ordinary stud provided that they are connected together throughout their height with mechanical
fastenings designed specifically for this purpose.
6.6.7 End bearing
Where studs bear onto horizontal timber members or horizontal timber members bear on to studs the
permissible compression perpendicular to grain stress should be checked.
NOTE See BS 5268-2 for permissible compression perpendicular to grain stress where wane is excluded at the junction of studs and
timber member, and in respect of length and position of bearing.
6.6.8 Gable apex panels

Gable apex panels are part of the external timber frame wall and should be designed to resist any vertical
or horizontal loads.

BS 5268-6.2:2001
6.6.9 Fixing of sheathing or lining

Where sheathing or linings are nailed to studs, the nails should be positioned so that the distance between
the nail and the edge of the board or the face of the stud is not less than 7 mm. Nails should be spaced at
centres not greater than 300 mm or less than 50 mm. Where plasterboard linings contribute to
racking resistance, nails should be no closer to the bound (or formed) edges of the board than 10 mm and
no closer to the ends of the board than 13 mm, and should be spaced at centres not exceeding 150 mm.
6.7 Racking resistance
6.7.1 Racking resistance of wall panels
Resistance to horizontal wind forces (racking resistance) should be provided by stiffening elements in the
plane of the wall. These should consist of timber frames that are sheathed with board materials or
diagonally braced or constructed with moment connections.
The racking strength and stiffness of timber frame wall panels should be determined by one of the methods
described in 6.7.2.
6.7.2 Methods of determining racking resistance of walls
The racking resistance of walls constructed from a number of braced or sheathed wall panels should be
derived using one of the following methods.
a) Assessment method (see 6.8)

The basic racking resistances given in Table 2 should be modified by application of material
modification factors (see 6.8) and wall modification factors (see 6.9) as appropriate. The racking
resistance of a wall should be calculated as:
RbLKmKw
where
Rb is the basic racking resistance (see Table 2) in kilonewtons per metre (kN/m);
L is the wall length in metres (m);
Km is the product of the material modification factors, K201K202K203;
Kw is the product of the wall modification factors, K204K205K206K207.
b) Load testing
Square panels (2.4 m × 2.4 m) should be tested in accordance with BS EN 594 and the results
interpreted in accordance with BS 5268-6.1:1996, clause 5 to find the basic test racking resistance
of a particular combination of materials and construction. In all respects the panel should be
representative of the construction to be used in the design.
The basic test racking resistance values derived from load testing should be substituted for the
values given in Table 2 and modified by the wall modification factors described in 6.9.
As load testing refers to a specific combination of materials and their fixings, the material
modification factors given in 6.8 (i.e. K201, K202 and K203) should not be applied to basic test
racking resistance. The racking resistance of a wall should be calculated as:
RbLKw
where
Rb is the basic test racking resistance (as derived from load testing) in kilonewtons per
metre (kN/m);
L is the wall length in metres (m);
Kw is the product of the wall modification factors, K204K205K206K207.
The additional contribution values of a secondary layer of category 1, 2 or 3 material (see Table 2)
should only be used where the basic test racking resistance of the primary board material does not
exceed 2.1 kN/m. In all other cases the additional contribution should be quantified by load testing
the primary board material.

BS 5268-6.2:2001
c) Load testing of full-sized walls

The walls should be tested in the form in which they are to be used, the permissible racking
resistance for the wall derived in accordance with BS EN 594 and the results interpreted in
accordance with BS 5268-6.1:1996, clause 5. Material and wall modification factors (K201 to K207)
should not be applied to wall racking test data derived in this manner.
d) Detailed analytical methods outside the scope of this British Standard
The material modification factors given in 4.8 and wall modification factors given in 4.9 should not
be applied to designs carried out independently of this British Standard.
6.7.3 Racking deflection
The permissible racking deflection should be within limits appropriate to the type of construction, having
particular regard to the possibility of damage to surface materials, ceilings, partitions, doors, windows and
finishings.
The basic racking resistances given in Table 2 are based upon a maximum deflection limit of 0.003 times
the panel height. Although it is acceptable to reduce the values given in Table 2 in respect of a smaller
deflection limit, it is not acceptable to increase the values given in the table to take account of a higher
limit.
6.7.4 The contribution of plasterboard to racking resistance
6.7.4.1 General
Where plasterboard is considered to make a contribution to racking resistance, its total contribution to
external sheathed walls and internal walls should not exceed 50 % of that provided by category 1 or 2
materials (see Table 2) when considering the walls providing resistance to wind forces in any one direction.
For plasterboard to contribute to the racking resistance:
a) the plasterboard should be fixed in accordance with Table 2;
b) the walls should be fully supported throughout their length and connected at head and base in such a
way as to ensure the transfer of applied shear forces.
6.7.4.2 Plasterboard linings to external sheathed walls
The contribution of plasterboard to external sheathed walls should be calculated by using the additional
lining contribution values given in Table 2 multiplied as appropriate by modification factors K203 to K207.
The plasterboard should be fixed on either the opposite face to the sheathing or on the same face as the
sheathing, providing that it is independently nailed and the nails are extended in length to take account of
the increased thickness of the wall lining.
6.7.4.3 Internal walls
Where internal walls, lined each side with plasterboard, are required to make a contribution to the racking
resistance of the building, the basic racking resistance should be taken from Table 2 using the basic racking
resistance for a plasterboard lined wall plus the contribution of the second layer. The value thus obtained
should be multiplied by modification factors K203 to K207 as appropriate.
Plasterboard lined internal walls are subject to the overall recommendations for plasterboard contribution
given in 6.7.4.1 and 6.7.4.4.
Door openings in internal walls should be regarded as structural discontinuities and the racking
resistances should be derived from the sum of the racking resistances of the plain panels on either side of
the openings.
In calculating the racking resistance of internal walls, the length should be taken as the length of each
plain section of the wall under consideration.

BS 5268-6.2:2001
6.7.4.4 Special internal walls

The restriction on the contribution of plasterboard to racking resistance, as required in 6.7.4.1 should not
apply in the case of internal walls only, lined each side with two or more layers of plasterboard where the
lowermost layer on each side is of a moisture resisting grade of plasterboard. In this case the full
contribution of plasterboard racking resistance given for a single layer of 12.5 mm plasterboard plus a
secondary layer, as given in Table 2 (see 6.7.4.3), may be taken for that wall without restriction. For
multi-layer constructions the length of nails given in Table 2 should be increased accordingly.
6.8 Assessment method for determining the basic racking resistance of certain material
combinations
6.8.1 General
Where the assessment method, as described in 6.7.2a), is to be used to determine the racking resistance of
a timber frame wall, the values given in Table 2 should be used for the relevant combination of sheathing
and lining materials.
NOTE 1 The values given in Table 2 are basic racking resistances based upon test evidence of fully sheathed wall panels and for the
generic materials described in clause 4. Specific test results derived from tests in accordance with BS EN 594 interpreted in
accordance with BS 5268-6.1:1996, clause 5 can be substituted for the values given in the table subject to the conditions given
in 6.7.2b).
NOTE 2 The values given in Table 2 take account of the appropriate load duration factors given in BS 5268-2 for loads of short and
very short term, and are based upon zero vertical load.
The use of Table 2 materials or test evidence of basic racking resistance should not be taken to imply that
a particular material is fit for the purpose for which it is intended. Designers should assure themselves of
the required durability for the intended use of materials.
6.8.2 Modification factors for variation in fixing and thickness of the materials described
in Table 2
6.8.2.1 Variation in nail diameter
For variations in nail diameter between 2.25 mm and 3.75 mm the values for basic racking resistance given
in Table 2 should be multiplied by K201:
Dn
K 201 = -------
3
where
Dn is the proposed nail diameter in millimetres (mm).

NOTE The recommended size of nail for fixing plasterboard is 2.65 mm diameter. No enhancement of basic racking resistance
is permitted for the use of any other size of nail.
6.8.2.2 Variation in nail spacing

For sheathings other than plasterboard the values for basic racking resistance given in Table 2 should be
multiplied by K202 to take account of variations in nail spacing:
1
K 202 = --------------------------------
( 0.6A + 0.4 )
where
A is given by Sp/sp;
Sp is the proposed perimeter spacing in millimetres (mm);
sp is the perimeter spacing of nails as given in Table 2, in millimetres (mm).
K202 should not be used to modify the basic racking resistance given in Table 2 for plasterboard.
Plasterboard nailed at centres greater than prescribed in Table 2 should not be considered to contribute to
racking resistance.
Where plasterboard is combined with other sheathing on the same wall, the combined basic racking
resistance value as given in Table 2 should not be increased by increasing the nail density.
NOTE The sheathing acting alone may provide a greater basic racking resistance under these circumstances and may be substituted
for the combined value.

BS 5268-6.2:2001
6.8.2.3 Variation in board thickness

The values for basic racking resistance given in Table 2 may be modified by K203 to account for variations
in thickness of sheathings or linings:
2
K 203 = æ 2.8B – B – 0.8ö
è ø
where
B is given by Tb/tb;
Tb is the proposed board thickness in millimetres (mm);
tb is the board thickness as given in Table 2, in millimetres (mm).
In no case should B be less than 0.75 or greater than 1.25.
6.9 Modification factors for wall shape, openings, vertical load and interaction
6.9.1 Shape factor for wall panels
The basic racking resistance should be modified to take account of the length and height of a timber frame
wall. The shape factor should be calculated as follows, where L is the length of wall in metres (m) and h is
the height of the wall panel in metres (m) under consideration:
a) for L/h of 1 or less:
K204 = L/h
b) for L/h greater than 1 and L not greater than 4.8 m:
K204 = (L/h)0.4
c) for L/h greater than 1 and L greater than 4.8 m:
K204 = (4.8/h)0.4
For wall panels exceeding 2.4 m in height and where an intermediate horizontal joint in the sheathing or
lining is required, such joints should be framed and nailed in accordance with the relevant
recommendations of clause 7.
Where wall panels are combined to form the lengths of wall given in this clause it is essential that the
following conditions are met.
a) Tops of individual wall panels should be linked by a member or construction that is continuous across
panel joints.
b) The faces of end studs of contiguous panels should be fixed such that any vertical shear is transferred.
In the absence of more specific information, end studs should be fixed with the equivalent of 3.35 mm
nails with a pointside penetration of at least 38 mm and at 300 mm distance centre to centre.
c) The coupled panels should be able to resist overturning forces.

BS 5268-6.2:2001
6.9.2 Window, door and other fully framed openings in walls

For a wall with framed openings, the permissible racking resistance should be reduced to take account of
the effect of framed openings. The opening effect factor K205 should be calculated as:
2
K 205 = ( 1 – 1.3p )
Or, in the specific case where openings are no closer to panel edges than 1 200 mm as:
2
K 205 = ( 1 – p )
In either case, when p > 0.75:
K 205 = 0
where:
p is given by Aa/At;
Aa is the aggregate area of opening in the wall;
At is the total area of wall including openings.
All edges other than the bases of door openings should be supported by members having a thickness not
less than the thickness of the studs.
A means should be provided of transferring horizontal forces in the plane of the panel above and below
openings. Where no such provision is made, the wall lengths on either side of the opening should be
designed as separate parts.
Where an opening is less than 300 mm from the corner of a building and the depth of opening is greater
than half the panel height, then the length of that part of the wall, up to and including the opening, should
be disregarded when determining the total length of wall (see 6.9.1).
When K205 is taken as (1 – 1.3p)2 and two framed openings are separated by less than 300 mm and the
heights of both openings are greater than half the panel height, then the area of opening should be taken
as that of the rectangle that encloses both openings.
When K205 is taken as (1 – p)2 and two framed openings are separated by less than 600 mm and the heights
of both openings are greater than half the panel height, then the area of opening should be taken as that
of the rectangle that encloses both openings.
NOTE This method of assessing the effect of wall openings takes account of the worst case of openings in a timber frame wall. Where
higher values of racking resistance can be obtained by considering a wall as a number of shorter lengths then this approach is
acceptable.
6.9.3 Small unframed openings

Recommendations for fully framed openings are given in 6.9.3, but where small unframed openings occur,
their size and position should be restricted as follows.
a) They should not exceed 250 mm in diameter or in length of side.
b) The clear distance between openings should be not less than the greatest dimension of the openings.
c) The clear distance between the edge of the sheathing and the edge of any opening should be not less
than the greatest dimension of the opening.
d) Not more than one such opening should occur in any one 600 mm width of sheathing or lining.
Smaller unframed openings may occur to a greater extent, but their aggregate opening area should not
exceed the total area of opening given in a).
The rules governing the position of openings given in b), c) and d) should also apply.

BS 5268-6.2:2001
6.9.4 Variation in vertical load on timber frame wall

Since the values of basic racking resistance given in Table 2 assume zero vertical load on the timber frame
wall panels, the basic racking resistance should be multiplied by K206 to take account of the effect of other
vertical load conditions.
The vertical load on the wall, F, used to calculate K206 should be calculated using only the dead or
permanent loading and any net effects of wind. K206 should be calculated as:
ì ü
ï 2 2.4 0.4 ï
K 206 = í 1 + æ 0.09F – 0.0015F ö æ --------ö ý
è ø è Lø
ï ï
î þ
where
F is the uniformly distributed vertical load in kilonewtons per metre (kN/m) (limited to a
maximum of 10.5 kN/m for the purpose of this calculation);
L is the length of wall in metres (m).
It is assumed that in applying K206 any uplift forces or overturning moments have been taken into account
and any necessary holding down fixing designed, therefore the vertical load should not be considered to be
less than zero. For the purposes of calculating K206 concentrated vertical loads should be converted into an
equivalent vertical uniformly distributed load:
2aF p
F = -------------
2
-
L
where
F is the equivalent uniformly distributed vertical load in kilonewtons per metre (kN/m);
Fp is the concentrated load in kilonewtons (kN);
a is the distance from Fp to the leeward end of the wall panel under consideration in metres (m);
L is the length of wall under consideration in metres (m).
NOTE A concentrated load can also be assumed to be developed by connections directly between the wall panel studs and the
substructure, or in the case of a corner or internal wall, the wall at right angles.
6.9.5 Interaction
In calculating the permissible racking resistance of walls, the basic racking resistance should be multiplied
by the modification factor K207, which has the value 1.1.
NOTE The basic racking resistance values given in Table 2 or as derived from test and modified as appropriate, by modification
factors K201 to K206, give reasonably true assessments of the racking resistance of plain walls when subjected to test racking loads.
When walls form part of completed buildings, experience shows that the method of assessment underestimates the permissible
racking resistance since it does not take into account factors such as the stiffening effect of corners and the interaction of walls and
floors through multiple fixings.
6.10 Contribution of masonry veneer to racking resistance

Where masonry veneer is considered to make a contribution to the permissible racking resistance for
sheathed timber frame walls comprising a combination of sheathing, lining and varying vertical load
conditions, the permissible racking resistance for the wall should be taken from the values given in
Table 3. This is provided that the wall ties and their fasteners have a minimum design horizontal shear
strength of 150 N at deformations of 5 mm or more and characteristic horizontal shear stiffness of not less
than 30 N/mm over the deformation range 0 mm to 5 mm when tested in accordance with the
recommendations of BS 5268-6.1:1996, Annex A.
The additional racking resistance for masonry cladding given in Table 3 should be applied only to those
parts of the wall comprising a minimum of storey height masonry backed by storey height timber frame
and Lm is not less than hm/4, where Lm is the length of masonry wall being considered in metres (m) and
hm is the storey height of masonry cladding in metres (m).
Masonry cladding should conform to 4.7.
The contribution of the masonry to the permissible racking resistance of the timber frame wall should be
determined by multiplying the relevant value in Table 3 by the total length of storey height masonry in the
wall.

BS 5268-6.2:2001
Under no circumstances should the contribution to permissible racking resistance provided only by the
masonry cladding exceed 25 % of the permissible racking resistance provided by the timber frame wall to
which it is fastened, when considering wind forces in any one direction.
NOTE Attention is drawn to 6.13.1.
Under no circumstances should the modification factors given in 6.9 be applied to the values given in
Table 3.
Table 3 gives ranges of wall tie density and the appropriate levels of racking resistance contribution that
may be assumed. The use of Table 3 values in no way implies that the density of ties required for a racking
resistance contribution is necessarily adequate to resist wind forces on the masonry wall. Designers should
check the actual density of ties required based upon an assessment of the relevant wind loads, shielding
factors etc.
Table 3 — Contribution of masonry cladding to racking resistance

Tie density Racking resistance
ties/m2 kN/m
>3.7 and <4.4a 0.4

74.4b 0.5
a 3.7 ties/m2 is typified by ties spaced at 600 mm horizontally and 450 mm vertically.
b 4.4 ties/m2 is typified by ties spaced at 600 mm horizontally and 375 mm vertically.
6.11 Racking resistance for walls braced by other than sheet materials
Racking resistance for walls braced by other means than with sheathing should be determined either by
calculation or by load testing in accordance with BS EN 594 and the results interpreted in accordance with
BS 5268-6.1:1996, clause 5.
Inclined bracing in the form of short pieces of blocking, each fitted between adjacent studs, should not be
used unless they are connected to lining, sheathing or gussets.
6.12 Joints
6.12.1 Mechanical joints
Except where justified by load testing or where permissible values are taken from this British Standard,
joints should be designed in accordance with BS 5268-2.
6.12.2 Glued joints
Glued joints should be designed in accordance with BS 5268-2 and manufactured in accordance with
BS 6446.
6.13 Other design considerations
6.13.1 Masonry cladding
Masonry cladding should be connected to the timber frame with wall ties that have sufficient strength and
stiffness to transfer wind forces to the timber frame wall. The wall ties and tying pattern should also ensure
adequate stability and robustness of the masonry cladding. Special care should be taken to ensure that
adequate connections are provided for small free-standing piers of masonry.
At vertical interruptions to masonry cladding, such as at windows and door reveals, movement joints and
sloping verges to gable walls, additional wall ties should be provided to ensure stability of the masonry
cladding.
6.13.2 Connections to accommodate differential movement
Wall ties between timber frame and masonry cladding should have sufficient vertical flexibility to permit
vertical downward movement of the timber frame in relation to the masonry cladding. In the absence of
more detailed information, the differential movement should be taken as 6 mm per storey height. Attention
should also be given to the movement characteristics of masonry.
Similar provision should be made for connections to other parts of the building where differential
movement may occur, such as connections between the timber frame and non-timber staircases, lift shafts
or other structures.

BS 5268-6.2:2001
6.13.3 Fixings and services

Consideration should be given at the design stage to provisions for fixing and jointing linings and claddings,
internal fittings (e.g. cupboards and wash basins) and the accommodation of services within timber frame
walls.
Allowance should be made in the design for any notching or drilling that is necessitated by the installation
of services. In the absence of more specific design information the recommendations of BS 5268-2 should
be adopted.
7 Workmanship
7.1 Fabrication
7.1.1 General
Drawings should be available showing the sizes of the wall panels and openings, and details of the framing,
sheathing, connections, cutting and notching, and specifications of all relevant materials.
Fabrication should be in accordance with the specifications and drawings.
A system of identification of pre-fabricated timber frame wall panels should be agreed between the
purchaser and the supplier and such identification should be clearly marked to ensure correct positioning
on-site in accordance with the detailed drawings.
7.1.2 Inspection
Fabricators of timber frame wall panels should provide purchasers and their authorized representatives
with the necessary facilities for inspection during fabrication and, by arrangement, should permit access
at all reasonable times to all places where relevant work is being carried out.
7.1.3 Moisture content
The moisture content of wall panels at the time of fabrication should be in accordance with the relevant
recommendations of BS 5268-2.
7.1.4 Timber tolerances
Timber used in the fabrication of wall panels should be within the tolerances for sawing and machining
specified in BS EN 336.
7.1.5 Assembly
Pre-fabricated timber frame wall panels should be assembled so as to ensure dimensional accuracy and
flatness.
All members should be accurately cut to ensure firm contact along the abutting faces, and should be
accurately cut to length to within a tolerance of ±1 mm. No gaps over 2 mm between abutting faces of
timber should be permitted unless allowed for in the design.
Timber frame wall panels should be fabricated so that horizontal and vertical dimensions are
within –05 mm of the size specified by the designer and no diagonal should exceed the square root of the
sum of the square of specified dimensions for opposite and adjacent edges of the panel.
All mechanical fasteners should be of the type and sizes specified and should be located so that the specified
packing, end and edge distances are maintained. Nails or screws should be fully driven home without
undue damage to the surface of the materials being joined.
Glued assemblies should conform to BS 6446.
7.1.6 Finger jointing
Glued finger joints in structural softwood should conform to BS EN 385.

BS 5268-6.2:2001
7.2 Handling and erection

7.2.1 Storage
Timber frame wall panels should at all times be stored on raised bearers to avoid contact with the ground
and vegetation and should be supported so as to prevent distortion. They should preferably be stored
vertically, but when stored horizontally, the sheathing should be uppermost to prevent any risk of water
collecting and supported to avoid warping. Reasonable precautions should be taken to avoid any damage
to materials as a result of exposure to rain.
7.2.2 Handling and transport
Care should be taken in handling to avoid damage to sheathing and local overstressing during lifting.
The general recommendations given in 7.2.1 for on-site storage should also be followed for storage during
transportation.
7.2.3 Erection
Modifications to timber frame wall panels, repairs to damaged panels or measures adopted to remedy
defects discovered after erection of a wall panel should be in accordance with this British Standard.
Panels should not be notched, cut or drilled unless expressly provided for in the design, or unless carried
out in accordance with BS 5268-2.
Panels should be erected accurately, aligned and positioned, and fastened to adjacent wall panels, floor and
roof in accordance with the detailed drawings. Deviations of panels from vertical should not exceed 6 mm
over a height of 2.4 m, pro rata for other heights, subject to a maximum deviation of 12 mm.
Care should be taken to ensure that adequate bearing is provided for the timber frame walls by the
supporting structure.
It is essential that nailing specifications for the on-site nailing of sheathings and linings, where such
materials are contributing to the structural performance of the walls, are adhered to.
7.2.4 Temporary bracing
Such temporary bracing or fixing as is required to ensure stability of wall panels, floor and roof during the
construction period should be provided and maintained for as long as is necessary.

BS 5268-6.2:2001
Bibliography
Standards publications
BS 5268-4.1:1978, Structural use of timber — Part 4: Fire resistance of timber structures —

Section 4.1: Recommendations for calculating fire resistance of timber members.
BS 5268-4.2:1990, Structural use of timber — Part 4: Fire resistance of timber structures —
Section 4.2: Recommendations for calculating fire resistance of timber stud walls and joisted floor
constructions.
BS 5268-7, Structural use of timber — Part 7: Recommendations for the calculation basis for span tables.
DD 140-2, Wall ties — Part 2: Recommendations for design of wall ties.

BS 5268-6.2:2001
BSI — British Standards Institution

BSI is the independent national body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the
international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they possess the latest amendments or
editions.
It is the constant aim of BSI to improve the quality of our products and services.
We would be grateful if anyone finding an inaccuracy or ambiguity while using
this British Standard would inform the Secretary of the technical committee
responsible, the identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures
that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all BSI, international and foreign standards publications should be
addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: [email protected]. Standards are also
available from the BSI website at http://www.bsi-global.com.
In response to orders for international standards, it is BSI policy to supply the
BSI implementation of those that have been published as British Standards,
unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and
international standards through its Library and its Technical Help to Exporters
Service. Various BSI electronic information services are also available which give
details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: [email protected].
Subscribing members of BSI are kept up to date with standards developments
and receive substantial discounts on the purchase price of standards. For details
of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: [email protected].
Information regarding online access to British Standards via British Standards
Online can be found at http://www.bsi-global.com/bsonline.
Further information about BSI is available on the BSI website at
http://www.bsi-global.com.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the
UK, of the publications of the international standardization bodies. Except as
permitted under the Copyright, Designs and Patents Act 1988 no extract may be
reproduced, stored in a retrieval system or transmitted in any form or by any
means – electronic, photocopying, recording or otherwise – without prior written
permission from BSI.
This does not preclude the free use, in the course of implementing the standard,
of necessary details such as symbols, and size, type or grade designations. If these
details are to be used for any other purpose than implementation then the prior
BSI written permission of BSI must be obtained.
389 Chiswick High Road Details and advice can be obtained from the Copyright & Licensing Manager.
London Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: [email protected].
W4 4AL

Structural Use of Timber

Uploaded by

Copyright:

Available Formats

Structural Use of Timber

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Structural Use of Timber

Uploaded by

Copyright:

Available Formats

BRITISH STANDARD BS 5268-6.

Part 6: Code of practice for timber

Section 6.2: Buildings other than

ICS 91.060.10; 91.080.20

NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW

Committees responsible for this

The preparation of this British Standard was entrusted by Technical

British Woodworking Federation

This British Standard, having

© BSI 31 January 2002

Amd No. Date Comments

The following BSI references 13630 31 January 2002 Indicated by a sideline

Committee reference B/525/5

ISBN 0 580 33276 4

© BSI 31 January 2002 i

This section of BS 5268 has been prepared by Subcommittee B/525/5, Structural

— Part 3: Code of practice for trussed rafter roofs;

ii © BSI 31 January 2002

© BSI 31 January 2002 1

BS 5390, Code of practice for stone masonry.

2 © BSI 31 January 2002

4.3 Sheathing materials

© BSI 31 January 2002 3

4.3.6 Other sheathings

4 © BSI 31 January 2002

5.2.2 Wind loading on masonry clad timber frame walls

a) The masonry walls should be constructed of:

5.2.3 Wind load transferred to timber frame wall

© BSI 31 January 2002 5

Table 1 — Modification factor, K200

6 © BSI 31 January 2002

6 Design of timber frame walls

6.2 Permissible stresses

6.4 Overall stability

6.5 Horizontal diaphragms

© BSI 31 January 2002 7

kN/m kN/m kN/m

Category 1 materials: 3.00 mm diameter wire nails at 1.68 0.28 0.84

8 © BSI 31 January 2002

6.6 Design of wall studs

direction perpendicular to the plane of the wall, in accordance with BS 5268-2.

6.6.5 Lateral deflection

6.6.8 Gable apex panels

© BSI 31 January 2002 9

6.6.9 Fixing of sheathing or lining

a) Assessment method (see 6.8)

10 © BSI 31 January 2002

c) Load testing of full-sized walls

© BSI 31 January 2002 11

6.7.4.4 Special internal walls

Dn is the proposed nail diameter in millimetres (mm).

6.8.2.2 Variation in nail spacing

12 © BSI 31 January 2002

6.8.2.3 Variation in board thickness

© BSI 31 January 2002 13

6.9.2 Window, door and other fully framed openings in walls

In either case, when p > 0.75:

6.9.3 Small unframed openings

14 © BSI 31 January 2002