PCW16 FXe

FUJITSU FLASH
MCU Programmer for

2
F MC-16FX
Specifications
FUJITSU FLASH
MCU Programmer for F2MC-16FX
Specifications
Version 1.03 26 March 2008
Software version: V01L04
©2007-2008 FUJITSU LIMITED Printed in Japan
1. Circuit diagrams utilizing Fujitsu products are included as a mean of illustrating typical semiconductor
applications. Complete information sufficient for construction proposes is not necessarily given.
2. The information contained in this document has been carefully checked and is believed to be reliable.
However, Fujitsu assumes no responsibility for inaccuracies.
3. The information contained in this document does not convey any license under the copy right, patent
right to trademarks claimed and owned by Fujitsu.
4. Fujitsu reserved the right to change products or specifications without notice.
5. No part of this publication may be copied or reproduced in any form or by any means, or transferred to
any third party without prior written consent of Fujitsu.
6. The products described in this document are not intended for use in equipment requiring high
reliability, such as marine relays and medical life-support systems. For such applications, contact your
Fujitsu sales representative.
7. If the products and technologies described in this document are controlled by the Foreign Exchange
and Foreign Trade Control Act established in Japan, their export is subject to prior approval based on
the said act.
ii
Ver date page contents
1.00 2007/2/1 --- New
Suffix is Changed
1.01 2008/1/23 --- Add
MB96F326A/R/Y,MB96F338R/U/Y,MB96F356A/R/Y
P4 Serial data I/O pins for MB96F326A/R/Y is corrected.
1.02 2008/2/20
P12 Internal motorola S decoder specifiction is added.
Add
1.03 2008/3/26 ---
MB96F379R/Y
iii
Contents
1. configuration Diagram....................................................................................................................1
2. Compatible Microcontrollers ..........................................................................................................2
3. Example of Connection for On-board Reprogramming by Programmer ......................................3
4. Pins used for on-board Reprogramming ........................................................................................4
5. Timing Chart for Each Pin .............................................................................................................5
6. Installation and Execution of Software .........................................................................................6
7. Programmer Functions...................................................................................................................7
7.1 Downloading ..............................................................................................................................8
7.2 Erasing and Programming......................................................................................................10
7.3 Internal motorola S decoder specification ..............................................................................12
7.4 Special specification ................................................................................................................13
8. Status of Operation Check ...........................................................................................................14
9. Others............................................................................................................................................15
10. Cautions ......................................................................................................................................18
iv
FUJITSU FLASH MCU Programmer for F2MC-16FX Specifications
1. CONFIGURATION DIAGRAM
WINDOWS
RS-232C Driver User system
RS-232C
Communication via UART MB96Fxxx
Using RS-232C cable connected to the personal computer (Windows PC), flash memory data in the
microcontroller mounted in the user system can be reprogrammed. Note that the user system must have
an RS-232C driver for communication with the microcontroller UART.
1
2. COMPATIBLE MICROCONTROLLERS
MB96F326A/R/Y, MB96F338R/U/Y, MB96F346A/R/Y,
MB96F347A/R/Y, MB96F348A/R/Y, MB96F348C/H/T,
MB96F356A/R/Y, MB96F379R/Y MB96F386R/Y,
MB96F387R/Y
2
3. EXAMPLE OF CONNECTION FOR ON-BOARD REPROGRAMMING

BY PROGRAMMER
User system
F2MC-16FX
1
0 at serial reprogramming MD2
0
1
0
1
0
RS-232C
Driver
RSTX
SIN *1
SOT *1
Communication via UART
RS-232C
*1: Check the settings of the serial data input/output pins used in each microcontroller.
The MD2, MD1, MD0 pins cannot be controlled by the PC and should be set in the user system.
When the RSTX pin is set from “Low” to “High” level after setting the MD2, MD1, MD0 pins, the
microcontroller enters the serial reprogramming mode, enabling serial reprogramming from the PC.
After the reprogramming, control is shifted to the normally-used mode as for MD2, MD1 and MD0 pins.
Then RSTX pin set from “Low” to “High” level executes user program.
Note: The port numbers of the SIN and SOT pins vary with the types of microcontrollers. See the
Tables in Chapter 4 for details.
When programming data to mass-produced products using the Yokogawa Digital Computer serial
programmer some time in the future, it is best to generate the patterns for serial clock pins on the
printed circuit board according to the connection example for serial programming described in the
Hardware Manual for each microcontroller.
3
4. PINS USED FOR ON-BOARD REPROGRAMMING

(1) Control pins for on-board programming
Function Pin Supplementary

Mode pins MD2, Should be controlled in flash memory reprogramming mode.
MD1, When MD2 and MD0 are set to “L” and MD1 is set to “H”, they enter the
MD0 reprogramming mode.
Reset pin RSTX Cancel reset after setting Mode pins to the flash reprogramming mode.
Serial data input SIN Note that the pin varies with the type of microcontroller.
pin
Serial data output SOT Note that the pin varies with the type of microcontroller.
pin
(2) Serial data I/O pins for each type of microcontroller
Type Serial Data Input Pin Serial Data Output Pin Supply Voltage
P08_2/SIN0 (UART0)*1 P08_3/SOT0 (UART0)*1

MB96F338R/U/Y
or or
MB96F346A/R/Y
MB96F347A/R/Y
or or 3V – 5V product
MB96F348A/R/Y
MB96F348C/H/T
or or
MB96F379R/Y
or or
MB96F386R/Y
P03_7/SIN1 (UART1)*2 P13_0/SOT1 (UART1)*2 3V – 5V product
MB96F387R/Y
or or
MB96F326A/R/Y
or or 3V – 5V product
MB96F356A/R/Y
1*: The user can select one channel of UART0-2 or 3.

2*: The user can select one channel of UART0-1 or 2.
3*: The user can select one channel of UART2 or 3.
4
5. TIMING CHART FOR EACH PIN
Input data to each pin of the microcontroller with the following timing on the basis of the input of the RSTX
pin.
Minimum values of setup and hold times of each signal on rising edge of RSTX
5
6. INSTALLATION AND EXECUTION OF SOFTWARE
If the old software version is installed, uninstall it first before installation.
Starting the installer to operate as instructed will complete the installation. Note that the install might not be
performed when a directory in a deep nest is specified as the install directory.
After installation, click the Windows Start button => Program => FUJITSU FLASH MCU Programmer =>
FMC16FX to start the programmer software.
6
7. PROGRAMMER FUNCTIONS
Erase, Blank Check, Program & Verify, Read & Compare, and Copy can be executed for flash memory
integrated into the microcontroller.
• Main dialog box

Programmer software is started to open the dialog box as shown below.
• Overview of operating procedure
First, complete setting of the user system (microcontroller board) that data is programmed to (see
Chapter 3). When the programmer software has been started or when setting (setting of Taget
Microcontroller or Crystal Frequency) has been changed, it is necessary to perform downloading
(described later).
After downloading terminates normally, perform procedures such as Erase and Programming.
7
7.1 Downloading
This section describes the operating procedure for downloading and the operating state of the program.
(a) Specify the type of microcontroller used in the user system in Target Microcontroller of the main dialog
box.
Please look at Chapter 2 about the selectable types.
Note:To select the type of microcontroller, use the Tab key to move to Target Microcontroller, select
with the cursor keys and then press the Enter key.
(b) Specify the frequency of the crystal oscillator input to the microcontroller in Crystal Frequency of the
main dialog box.
The frequency of the crystal oscillator that can be specified for each type of microcontroller is limited as
follows.
Product Type Frequency of Crystal Oscillator (MHz)

MB96F326A/R/Y 4,5,8,10,16
MB96F338R/U/Y 4,5,8,10,16
MB96F346A/R/Y 4,5,8,10,16
MB96F347A/R/Y 4,5,8,10,16
MB96F348A/R/Y 4,5,8,10,16
MB96F348C/H/T 4,5,8,10,16
MB96F356A/R/Y 4,5,8,10,16
MB96F379R/Y 4,5,8,10,16
MB96F386R/Y 4,5,8,10,16
MB96F387R/Y 4,5,8,10,16
Notice:This program will not operate normally if the microcontroller uses a crystal oscillator frequency
not listed in the above table.
(c) Select the COM port of the PC connected to the user system.
Click the [Set Environment] button in the main dialog box to open the setup window. When the [COM
PORT] tab in the setup window is clicked, the specifying window is opened. Select any of the following
COM ports.
COM1, COM2, COM3, COM4, COM5, COM6, COM7, COM8
8
(d) Execution of downloading
Click the [Download] button.
If the following dialog window is opened, Input a reset signal to the microcontroller to start the program
in the flash programming mode and then click the [OK] button
Downloading is performed to open the “Download” window. When downloading is completed normally,
the following dialog window opens.
When the [OK] button is clicked to close the dialog window, the [Erase], [Blank Check], [Program &
Verify], [Read & Compare] and [Copy] buttons are enabled.
Note: Downloading can also be performed using the Tab key to move to the [Download] button and
pressing the Enter key or pressing the ALT and D keys at the same time.
9
7.2 Erasing and Programming
This section explains how to specify Hex File and the processing and operation performed when the
[Erase], [Blank Check], [Program & Verify], [Read & Compare], [Copy] and [Full Operation
(D+E+B+P)] buttons are clicked.
Each execution can also be performed by pressing the key corresponding to the underlined character in the
button name while pressing the ALT key. (Hex File is a O character in Open button, click the ALT + O
keys).
(a) Hex File: Select the file to be programmed to flash memory
Specify the Motorola-S or Intel-HEX format file to be programmed to flash memory in the microcontroller.
Although the specification method by drags and drops a direct file from Explorer etc. is recommended, it
can specify also by the file appointed window displayed by pushing the [Open] button.
Hex File must be specified to execute [Program & Verify], [Read & Compare] and [Full Operation
(D+E+B+P)]. Since it is decoded at the head of these processings each time, even if the specified
Motorola S or Intel-HEX format file changes specification of a file just before processing, it is OK.
(b) Erase: Erase all flash memory areas
All flash memory must be in the erase state (0xff) when programming a new program to it. By pushing
this button, a chip erase command is published to FLASH and elimination is performed.
In addition, a blank check does not perform this command.
(c) Blank Check: Check that all flash memory areas are blank
This button is clicked to check that all flash memory is in the erase state (0xff).
10
(d) Program & Verify: Program data to flash memory
This button is clicked to program the Motorola-S or Intel-HEX format file specified in Hex File to flash
memory in the microcontroller concurrently with verification. An error dialog is displayed, when writing is
performed for 512 bytes of every block and a CRC error is detected by the block.
This dialog If YES is pushed, the block of an error will be resent and it will continue writing. A push on
NO interrupts write-in processing.
(e) Read & Compare: Compare Hex File with data in flash memory in microcontroller
This button is clicked to compare data in the Motorola-S or Intel-HEX format file specified in Hex File
with data in flash memory in the microcontroller. Like the [Program & Verify] processing, The data of
FLASH is transmitted for 512 bytes of every block, a CRC error check is performed, and comparison
processing is performed.
(f) Copy: Save data in flash memory in microcontroller to file
This button is clicked to read data from flash memory integrated into the microcontroller and save it as
an Motorola-S format file. Like [Read & Compare] processing, FLASH memory reading is performed
for 512 bytes of every block, and a CRC error check is performed similarly. A preservation place folder
is specified, and if a file name is inputted and [Save] button is pushed, processing will begin.
(g) Full Operation (D+E+B+P): Automatic programming
Operation to [Download] to [Program & Verify] is performed by package.
In the case of a blank chip, processing is performed in order of [Download], [Blankcheck], and
[Program & Verify]. When it is not a blank chip, processing is performed in order of [Download],
[Blankcheck], [Erase], [Blankcheck], and [Program & Verify].
11
7.3 Motorola-S format decoder specification
Before programming, Motorola-S format Decoder of programmer changes Motorola S format data into
binary data, according to the following specification.
(a) The decoder does not error when overlap of addresses occurs.
The decoder does not error about overlap of address. If user writes a data on an address
which was already written another data before, former data is overwritten by new data.
(b) Available address

If user writes a data beyond an address range of FLASH memory, programming results in
an error. But if an address range of whole FLASH memory does not continue, decoder does
not give an error and programming procedure goes on. For example, user can program a
FLASH memory which starts an address H'F90000 and ends an address H'FFFFFF and
does not have memory function between H'FC0000-H'FCFFFF even if user tries to
program on such eclipse address range.
(c) About the error detected by the decoder.

The error detected by the decoder is the following (1)-(4). When these errors are detected,
processing is interrupted by the decoder. Then the line number and the cause of the error
are displayed in the dialog window.
(1) file error
The start of the line is not "S".
(2) S-format error
The start of the line is not "S0","S1","S2","S3","S4","S5","S6","S7","S8" and "S9".
(3) decode error
・There are character except "0123456789ABCDEF".("S" is excluded. See (1) and (2).)
And, the small letter "abcdef" cannot be used.
・The data number of one line is insufficient.
・The SUM data is different.
(4) address error
There is data besides the FLASH area. (See b.Available address)
(d) Other detail

The decoder skips a line. even if the line is contained only new-line code NL and
programming goes on.
A line beginning with "S0","S5","S7","S8" and "S9" is ignored and decoder skips such lines
in S format file without error.
The decoder does not give an error and programming goes on when SUM is correct, even if
the line is longer than a length specified by "LENGTH". In this case, the rest of the data
beyond a length specified by "LENGTH" is ignored.
12
7.4 Special specification
Now, there is no kind to which special specification is applied.
13
8. STATUS OF OPERATION CHECK
• Specifications for PC used for operation check
PC: FUJITSU FMV2TXH161

CPU: PentiumⅡ 450 MHz
OS: Japanese and English version of Windows XP SP1
Memory: 192 MB
14
9. OTHERS
(A) Setting of sound output
The setting of sound generated when an error occurs and processing is terminated normally can be
changed.
Select the [Sound] tab in the setup window that opens when the [Set Environment] button is clicked.
• To output sound, put a check in the Enable sound checkbox.
• Next, the event to take out sound is chosen in the Event column, and the sound in the event is set up
by specifying SundType and WaveFile under it in the state.
• Select Wave or Beep as the type of sound to be output in Sound type.
• Set the wave file to be output in the Wave file column only when Wave is selected. When the [Open]
button is clicked, the File Open window is opened. Select the Wave file to be output. The [Play]
button is used to play the set Wave file. The [Stop] button is used to stop the Wave file.
(B) Setting of tooltips display
The tooltips display can be either “enabled” or “disabled”.
Select the [Tooltips] tab in the setup window that opens when the [Set Environment] button is
clicked.
When a checkmark is put in the tooltips checkbox to move the mouse cursor over the contents such as
buttons in the dialog window, simple help (the full path of a file for Hex File) is displayed.
15
(C) Error messages

Many error messages are displayed owing to the setting mistake of hardware and software.
the case where an error is outputted in addition even if it checks these in detail, please tell the person
in charge of software acquisition origin a detailed condition.
No.001 Download error*1

Cause: The response of download processing is unusual.
Action: Please check connection and a setup of hardware.
No.003 Timeout error

Cause: The response of a command does not come on the contrary.
Action: Please check connection and a setup of hardware.
No.006 Unable to open COM port

Cause: Another application is using COM.
Action: Please check the use situation and port number of a COM port.
No.007 Unable to open Download file

Cause: m_flash.xxx not found
Action: Please reinstall this software.
No.009 Unable to gain COM port info

Cause: It will be in the state where the target COM port can be used.
Action: Please check the number of a COM port and setup to be used.
No.010 Unable to change COM port setting

Cause: A communication setup cannot be set as the target COM port.
Action: Please inform support of condition.
No.011 Communication error

Cause: The unusual command response was received.
Action: Please reperform by improving connection and a setup of hardware.
No.012 Read error

Cause: The response at the time of read&compare or copy processing is unusual.
Action: Please reperform by improving connection and a setup of hardware.
No.013 Program error

Cause: The response at the time of Program&Verify processing is unusual.
Action: Please reperform by checking whether a chip is blank.
No.015 COM port write error

Cause: There is the possibility of the abnormalities of a COM port driver or the port itself.
No.016 COM port read error

Cause: There is the possibility of the abnormalities of a COM port driver or the port itself.
No.017 File access error

Cause: Access of a m_flash.xxx file went wrong.
Action: Return the folder and file configurations to the installation defaults.
16
No.018 Erase error *1

Cause: The response at the time of erase processing is unusual. There is the possibility that a
chip is poor.
Action: Please improve a setup of hardware or exchange chips.
No.101 Please set "hex file"

Cause: “Hex file” not set
Action: Set “hex file” in the dialog box.
No.207 memory is not available

Cause: Unable to allocate memory for execution
Action: Quit any running application and retry.
Please redo from download operation *2
*1: “MCU xxH” is displayed if the error cause is returned from the microcontroller at a download error.
“MCU xxH” means:
MCU 02H → SUM error at downloading
MCU 04H → Abnormal termination at downloading
*2: This is an additional message. It is displayed as necessary after other messages are displayed.
17
10. CAUTIONS
No responsibility is taken about the problem which faced this software use.
The operation of this program is not assured on NEC PC98 series personal computers.
The PC programming software has the possibility of receiving the influence by the communications cable,
the outside environment, and the PC. Therefore, please evaluate it enough when you use the software.
Please use programming systems of programmer venders when you write two or more devices at the same
time.
When using this program, there are restrictions on frequencies that are input to the microcontroller as
original oscillations. For details, see (b) of Section 7.1.
18

PCW16 FXe

Uploaded by

Copyright:

Available Formats

PCW16 FXe

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PCW16 FXe

Uploaded by

Copyright:

Available Formats

FUJITSU FLASH

MCU Programmer for

4. Fujitsu reserved the right to change products or specifications without notice.

RS-232C Driver User system

Communication via UART MB96Fxxx

3. EXAMPLE OF CONNECTION FOR ON-BOARD REPROGRAMMING

4. PINS USED FOR ON-BOARD REPROGRAMMING

Function Pin Supplementary

(2) Serial data I/O pins for each type of microcontroller

P08_2/SIN0 (UART0)*1 P08_3/SOT0 (UART0)*1

1*: The user can select one channel of UART0-2 or 3.

5. TIMING CHART FOR EACH PIN

6. INSTALLATION AND EXECUTION OF SOFTWARE

If the old software version is installed, uninstall it first before installation.

• Main dialog box

• Overview of operating procedure

Please look at Chapter 2 about the selectable types.

Product Type Frequency of Crystal Oscillator (MHz)

(d) Execution of downloading

Click the [Download] button.

7.2 Erasing and Programming

(a) Hex File: Select the file to be programmed to flash memory

(b) Erase: Erase all flash memory areas

In addition, a blank check does not perform this command.

(d) Program & Verify: Program data to flash memory

(f) Copy: Save data in flash memory in microcontroller to file

(g) Full Operation (D+E+B+P): Automatic programming

Operation to [Download] to [Program & Verify] is performed by package.

7.3 Motorola-S format decoder specification

(b) Available address

(c) About the error detected by the decoder.

(d) Other detail

7.4 Special specification

Now, there is no kind to which special specification is applied.

8. STATUS OF OPERATION CHECK

• Specifications for PC used for operation check

PC: FUJITSU FMV2TXH161

• To output sound, put a check in the Enable sound checkbox.

• Select Wave or Beep as the type of sound to be output in Sound type.

(B) Setting of tooltips display

The tooltips display can be either “enabled” or “disabled”.

(C) Error messages

No.001 Download error*1

No.003 Timeout error

No.006 Unable to open COM port

No.007 Unable to open Download file

No.009 Unable to gain COM port info

No.010 Unable to change COM port setting

No.011 Communication error

No.012 Read error

No.013 Program error

No.015 COM port write error

No.016 COM port read error

No.017 File access error

No.018 Erase error *1

No.101 Please set "hex file"

No.207 memory is not available

Please redo from download operation *2

You might also like

P08_2/SIN0 (UART0)1 P08_3/SOT0 (UART0)1