PRODUCT DATA SHEET

Sikaflex®-1A
ELASTOMERIC JOINT SEALANT / ADHESIVE

PRODUCT DESCRIPTION ▪ Can be applied to green concrete 24 hours after pour

▪ Can be applied to damp concrete 1 hour after getting
Sikaflex®-1A is a premium-grade, high-performance, wet
moisture-cured, 1-component, polyurethane-based, ▪ Non-staining.
non-sag elastomeric sealant. Sikaflex-1a can be used in ▪ Jet fuel resistant.
green and damp concrete applications. Meets Federal ▪ Certified to NSF/ANSI/CAN 61 for potable water
Specification TT-S-00230C, Type II, Class A. Meets ASTM (meets applicable requirements of NSF/ANSI 600).
C920, Type S, Grade NS, Class 35, Use T, NT, O, M, A, I. ▪ Urethane-based; suggested by EPA as a caulk and crack
Canadian standard CAN/CGSB 19.13-M87. sealant for radon reduction.
▪ Paintable with water-, oil- and rubber-based paints.
▪ Capable of ±35% joint movement.
USES
▪ Designed for all types of joints where maximum depth APPROVALS / STANDARDS
of sealant will not exceed 1/2 in.
▪ Excellent for small joints and fillets, windows, door ▪ ASTM C920, Type S, Grade NS, Class 35, Use T, NT, O,
frames, reglets, flashing, common roofing detail M, A, I
▪ SWRI validated acc. to ASTM C719 (No. 0123-S0128)
applictions, and many construction adhesive
▪ Federal specification TT-S-00230 C Type II, Class A
applications.
▪ Suitable for vertical and horizontal joints; readily ▪ Canadian Standard CAN/CGSB 19.13-M87
placeable at 40°F ▪ Certified to NSF/ANSI/CAN 61 for potable water
▪ Has many applications as an elastic adhesive between (meets applicable requirements of NSF/ANSI 600).
materials with dissimilar coefficients of expansion.
▪ Submerged conditions, such as canal and reservoir
joints.

CHARACTERISTICS / ADVANTAGES
▪ Eliminates time, effort, and equipment for mixing,
filling cartridges, pre-heating or thawing, and cleaning
of equipment.
▪ Fast tack-free and final cure times.
▪ High elasticity - cures to a tough, durable, flexible
consistency with exceptional cut and tear -resistance.
▪ Stress relaxation.
▪ Excellent adhesion - bonds to most construction
materials without a primer.
▪ Excellent resistance to aging, weathering.
▪ Proven in tough climates around the world.

Product Data Sheet

Sikaflex®-1A
June 2023, Version 01.05
020511010000000008

1/4
PRODUCT INFORMATION
Packaging 10.1 fl. oz. (300 ml) cartridge, 20 fl. oz. (600 ml) sausage,
4.5 gal (17 L) in a 5 gal pail, 52 gal (197 L) in a 55 gal drum
Shelf Life Cartridge and Sausage: 12 months in original, unopened packaging.
Pail and Drum: 6 months in original, unopened packaging.
Storage Conditions Store at 40°-95°F (4°-35°C).
Color White, colonial white, aluminum gray, limestone, black, dark bronze, capitol
tan, stone and medium bronze. Special architectural colors on request.

TECHNICAL INFORMATION
Shore A Hardness (21 day) 45±5 (ASTM C 661)

Tensile stress at specified elongation 21 day Tensile Stress 175 psi (1.21 MPa) (ASTM D 412)
Stress @ 100% 85 psi (0,59 N/mm2)

Elongation at Break 550 % (ASTM D-412)

Movement Capability ±35 % (ASTM C-719)

Adhesion in peel Substrate Peel Strength Adhesion loss (ASTM C-794)

Concrete 20 lbs 0% (TT-S-00230C)
Aluminium 20 lbs 0%
Glass 20 lbs 0%

Tear Strength 55 lb./in. (ASTM D-624)

Service Temperature −40 °F to +170 °F

Chemical Resistance Good resistance to water, diluted acids, and diluted alkalines. Consult
Technical Service for specific data.
Resistance to Weathering Excellent

APPLICATION INFORMATION
Coverage 10.1 oz Cartridge: Yield in Linear Feet
Width/Depth 1/4" 3/8" 1/2"
1/4" 24.3
3/8" 16.2 10.8
1/2" 12.1 8.1 6.1
3/4" 8.1 5.4 4.0
1" 3.0
1.25" 2.4
1.5" 2.0
20 oz Sausage: Yield in Linear Feet
Width/Depth 1/4" 3/8" 1/2"
1/4" 48.1
3/8" 32.1 21.4
1/2" 24.1 16.0 12.0
3/4" 16.0 10.7 8.0
1" 6.0
1.25" 4.8
1.5" 4.0

Product Data Sheet

Sikaflex®-1A
June 2023, Version 01.05
020511010000000008

2/4
 1 gallon: Yield in Linear Feet
Width/Depth 1/4" 3/8" 1/2"
1/4" 307.9
3/8" 205.3 136.8
1/2" 153.9 102.6 77.0
3/4" 102.6 68.4 51.3
1" 38.5
1.25" 30.8
1.5" 25.7

Cure Time 4 to 7 days (73 °F / 50 % r.h.)

Curing Rate up to 1/8" after 24 hours (73 °F / 50 % r.h.)
Tack Free Time 3 to 6 hours (73 °F / 50 % r.h.)

BASIS OF PRODUCT DATA ▪ The depth of sealant in horizontal joints subject to

traffic is 1/2 in.
Results may differ based upon statistical variations ▪ Do not tool with detergent or soap solutions.
depending upon mixing methods and equipment, ▪ Do not use in contact with bituminous/asphaltic
temperature, application methods, test methods, actual materials.
▪ In green concrete applications sealing joints in poor or
site conditions and curing conditions.
low strength concrete 24 hours after pour may impact
ability of sealant to gain proper adhesion.
AVAILABILITY/WARRANTY ▪ In damp concrete applications all standing water and
excess water must be eliminated prior to the 60
▪ Pre-treatment Sealing and Bonding Chart minute waiting time.
▪ Technical Manual: Facade Sealing
ENVIRONMENTAL, HEALTH AND SAFETY
LIMITATIONS
For further information and advice regarding
▪ Allow 1 week cure at standard conditions when using transportation, handling, storage and disposal of
Sikaflex-1a in total water immersion situations. chemical products, user should refer to the actual Safety
▪ When overcoating with water, oil and rubber based Data Sheets containing physical, environmental,
paints, compatibility and adhesion testing is essential. toxicological and other safety related data. User must
▪ Sealant should be allowed to cure for 7 days prior to read the current actual Safety Data Sheets before using
overcoating any products. In case of an emergency, call CHEMTREC
▪ Avoid exposure to high levels of chlorine. (Maximum
at 1-800-424-9300, International 703-527-3887.
continuous level is 5 ppm of chlorine.)
▪ Maximum depth of sealant must not exceed 1/2 in.;
minimum depth is 1/4 in. APPLICATION INSTRUCTIONS
▪ Maximum expansion and contraction should not
exceed 35% of average joint width. SUBSTRATE PREPARATION
▪ Do not cure in the presence of curing silicone sealants.
▪ Avoid contact with alcohol and other solvent cleaners Product Conditioning: Condition material to 65°-75°F
during cure. before using.
▪ Do not apply when moisture-vapor-transmission Clean all surfaces. Joint walls must be sound, clean,
condition exists from the substrate as this can cause frost-free, and free of oil and grease. Curing compound
bubbling within the sealant. residues and any other foreign matter must be
▪ Use opened units the same day. thoroughly removed. A roughened surface will also
▪ When applying sealant, avoid air-entrapment. enhance bond. Install bond breaker tape or backer rod
▪ Since system is moisture-cured, permit sufficient to prevent bond at base of joint. Priming is not usually
exposure to air. necessary. Most substrates only require priming if
▪ White color tends to yellow slightly when exposed to testing indicates a need or where sealant will be
ultraviolet rays. subjected to water immersion after cure.
▪ Light colors can yellow if exposed to direct gas fired For green concrete applications control joints must be
heating element. cut 8 hours prior to sealant installation and in expansion
▪ The ultimate performance of Sikaflex-1a depends on joint forms must be removed 4 hours prior to sealant
good joint design and proper application with joint installation. For wet concrete applications all excess or
surfaces properly prepared. standing water must be displaced and concrete must

Product Data Sheet

Sikaflex®-1A
June 2023, Version 01.05
020511010000000008

3/4
then dry for a minimum of 60 min prior to sealant Remover-208 immediately after use. Hardened material
installation. Consult Sikaflex Primer Technical Data Sheet can only be removed mechanically.
or Technical Service for additional information on
priming. OTHER RESTRICTIONS
APPLICATION METHOD / TOOLS See Legal Disclaimer.
Recommended application temperatures: 40°-100°F. For
cold weather application, condition units at LEGAL DISCLAIMER
approximately 70°F; remove prior to using. For best
performance, Sikaflex-1a should be gunned into joint • KEEP CONTAINER TIGHTLY CLOSED
when joint slot is at mid-point of its designed expansion • KEEP OUT OF REACH OF CHILDREN
and contraction. Place nozzle of gun into bottom of the • NOT FOR INTERNAL CONSUMPTION
joint and fill entire joint. Keep the nozzle in the sealant, • FOR INDUSTRIAL USE ONLY
continue on with a steady flow of sealant preceding the • FOR PROFESSIONAL USE ONLY
nozzle to avoid air entrapment. Avoid overlapping of
sealant to eliminate entrapment of air. Prior to each use of any product of Sika Corporation, its
subsidiaries or affiliates (“SIKA”), the user must always
Sikaflex-1a can be applied on green concrete after the read and follow the warnings and instructions on the
concrete has cured for a minimum of 24 hours at product’s most current product label, Product Data
75°F.Control joints must be cut and open for min of 8 Sheet and Safety Data Sheet which are available at
hours prior to application. Expansion joints must have usa.sika.com or by calling SIKA’s Technical Service
forms removed a minimum of 4 hours prior to Department at 1-800-933-7452. Nothing contained in
application. For damp concrete applications Sikaflex-1a any SIKA literature or materials relieves the user of the
can be applied 60 minutes after any and all water has obligation to read and follow the warnings and
been displaced. instructions for each SIKA product as set forth in the
current product label, Product Data Sheet and Safety
Tooling & Finishing Data Sheet prior to use of the SIKA product.
Tool sealant to ensure full contact with joint walls and
remove air entrapment. Joint dimension should allow SIKA warrants this product for one year from date of
for 1/4 inch minimum and 1/2 inch maximum thickness installation to be free from manufacturing defects and
for sealant. Proper design is 2:1 width to depth ratio, For to meet the technical properties on the current Product
use in horizontal joints in traffic areas, the absolute Data Sheet if used as directed within the product’s shelf
minimum depth of the sealant is 1/2 in. and closed cell life. User determines suitability of product for intended
backer rod is recommended. use and assumes all risks. User’s and/or buyer’s sole
remedy shall be limited to the purchase price or
Removal replacement of this product exclusive of any labor costs.
Use personal protective equipment (chemical resistant NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALL
gloves/goggles/clothing). Without direct contact, APPLY INCLUDING ANY WARRANTY OF
remove spilled or excess product and placed in suitable MERCHANTABILITY OR FITNESS FOR A PARTICULAR
sealed container. Dispose of excess product and PURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGAL
container in accordance with applicable environmental THEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.
regulations. SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THIS
PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT
Over Painting OR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELD
Allow 1-week cure at standard conditions when using BY OTHERS.
Sikaflex-1a in total water immersion situations and prior
to painting. Sale of SIKA products are subject to the Terms and
Conditions of Sale which are available at
CLEANING OF TOOLS https://usa.sika.com/en/group/SikaCorp/termsandconditions.html
or by calling 1-800-933-7452.
Clean all tools and application equipment with Sika®

Sika Corporation
201 Polito Avenue
Lyndhurst, NJ 07071
Phone: +1-800-933-7452
Fax: +1-201-933-6225
usa.sika.com

Sikaflex-1A-en-US-(06-2023)-1-5.pdf

Product Data Sheet

Sikaflex®-1A
June 2023, Version 01.05
020511010000000008

4/4