Scribd Logo
Upload

Welcome to Scribd!

  • 47 views

    Template MRFW

    Uploaded by

    Dylan Trigg
    This document provides a weld procedure specification for multi-run fillet welds using the MAG welding process. It specifies the welding details including wire feed speed, current, voltage and heat input for three runs. The filler material is a G38 4M G3SI1 wire and the joint design and welding sequence are also specified. Post weld heat treatment is not required and interpass temperatures will be checked using an infrared thermometer.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Template MRFW

    Uploaded by

    Dylan Trigg
    47 views1 page
    This document provides a weld procedure specification for multi-run fillet welds using the MAG welding process. It specifies the welding details including wire feed speed, current, voltage and heat input for three runs. The filler material is a G38 4M G3SI1 wire and the joint design and welding sequence are also specified. Post weld heat treatment is not required and interpass temperatures will be checked using an infrared thermometer.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a weld procedure specification for multi-run fillet welds using the MAG welding process. It specifies the welding details including wire feed speed, current, voltage and heat input for three runs. The filler material is a G38 4M G3SI1 wire and the joint design and welding sequence are also specified. Post weld heat treatment is not required and interpass temperatures will be checked using an infrared thermometer.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    47 views1 page

    Template MRFW

    Uploaded by

    Dylan Trigg
    This document provides a weld procedure specification for multi-run fillet welds using the MAG welding process. It specifies the welding details including wire feed speed, current, voltage and heat input for three runs. The filler material is a G38 4M G3SI1 wire and the joint design and welding sequence are also specified. Post weld heat treatment is not required and interpass temperatures will be checked using an infrared thermometer.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 1

    Company Name

    LOGO Address Line 1


    Address Line 2
    Town, County
    Postcode
    Weld Procedure Specification (WPS)
    Location: Workshop Joint Type: Multi Run Fillet
    Manufacturer’s WPS No: MRFW-WPS001 Method of Preparation: Light Grinding
    WPQR: MRFW Parent Material Designation: BS EN 10025 S355JR
    Manufacture: Company Name Material Thickness: X to Xmm
    Welders Name: Welders Name Outside Diameter: N/A
    Welding Process: 135 (MAG) Welding Position: PA (Flat)

    Joint Design Welding Sequence

    Welding Details:

    Size of Type of Wire Feed Travel Heat


    Welding Welding Current Voltage Transfer
    Run Filler Current/ Speed Speed Input
    Process Direction A V Mode
    Material Polarity M/min mm/sec KJ/min
    1 MAG PA Xmm XXX - XXX XX - XX DC+ve X X 0.XXX – 0.XXX DIP
    2 MAG PA Xmm XXX - XXX XX - XX DC+ve X X 0.XXX – 0.XXX DIP
    3 MAG PA Xmm XXX - XXX XX - XX DC+ve X X 0.XXX – 0.XXX DIP

    Filler Metal Classification & Trade Name EN 14341-A: G38 4M G3SI1 / G38 (Brand Name Wire)
    Any Special Baking or Drying Stored in accordance with manufacturers recommendations.
    Gas/Flux: - Shielding/Backing Gas retail name (ISO 14175 – M24 ArCO7/2.5
    Shielding Gas Flow Rate 15L/Minute
    Tungsten Electrode Type/Size NA
    Details of Back Gouging/Backing NA
    Preheat Temperature X℃
    Interpass Temperature (℃) ‘Maximum recorded in WPQR’ (Note 4)
    Post Weld Heat Treatment NA
    Time, Temperature, Method NA
    Heating & Cooling Rates NA
    Other Information 1: Nozzle diameter = Xmm
    2: In all cases the gap between component parts shall be kept to a minimum
    3: Actual run sequence will depend on the thickness of the parent material
    4: Interpass temperature shall be checked using infrared thermometer
    5: Weld finish to be left as-welded unless specified otherwise
    6: Weaving Xmm
    7: Torch angle X°

    RWC Signature:

    Key:
    NA = Not Applicable G = Globular S = Spray

    You might also like