Unit 1

Stone Masonry

Stone is an economical material used for the construction

of a building. In some parts of the country, stones are
abundantly available in nature. These stones are cut
and dressed to proper shapes and sizes as per the need
and requirement.

Material Required for Stone Masonry

1. Stones
2. Mortar

Stones
The stones selected for construction should be hard,
durable, tough and free from any defects. The selection of
stone for stone masonry depends upon— (a) availability,
(b) ease of working, (c) appearance, (d) strength and
stability, (e) polishing characteristics, (f) economy, and
(g) durability.
 The table below lists the different types of stones
used for different purposes.
S. No. Purpose Stone Used
1. Heavy engineering work, Granite and gneiss
for example, docks, break
waters, lighthouses, bridge
piers, etc.
2. Buildings in industrial Granite and compact
towns sandstones
3. Pavements, railway ballast, Granite and ballast
door sills and steps
4. Fire resistant works Compact sandstone
5. Carving and ornamental Marble and laterite
works
6. Facade and architectural Marble, granite and
closer grained sandstone

Mortar
Mortar is required to keep the stones in position.
It is prepared by mixing lime or cement with sand and
water. It is placed in the joints. The type of mortar to
be used depends on the strength required, load on the
structure, resistance desired for climatic changes, etc.
The usual varieties are— lime mortar, cement mortar,
cement lime mortar and lime cement mortar.
In cement lime mortar, a portion of the cement is
replaced by hydrated lime. It spreads more easily under
the trowel and produces a more elastic material. In lime
cement mortar a portion of lime is replaced by cement.
It makes the mortar stronger, more smoother and
workable and also the mortar sets earlier.
Stones are categorised as per use in structural
members (an object that represents a beam, brace, or
column in a drawing) and location. These are:
1. Sill
2. Corbel
3. Cornice
4. Coping
5. String course
6. Through stone
• Sill is the bottom surface of a door or a window
opening (Fig.1.1). The sill stones are dressed in
Sill such a way that they prevent the entry of water into
Fig. 1.1: Sill
the building.
Assistant Mason – Class X

Unit 1.indd 2 12/2/2020 12:36:05 PM

 • Corbel is a projecting stone, which is usually used to
serve as a support for roof truss, beam and weather
sheds, etc., as shown in Fig.1.2. Corbels are generally
moulded and are given an ornamental treatment.
The corbels should extend at least two-thirds of their
length into wall.
• Cornice is a course of stone provided at the top
of a wall. It is generally moulded and is given
an ornamental treatment. It is weathered and
threaded to dispose of rainwater. Sufficient bearing
and extra weight at the top should be provided in Fig. 1.2: Corbel
the form of a parapet wall, to prevent overturning of
the cornice.
• Coping is a course of stone, which is laid at
the top of the wall, so as to protect the wall from
rainwater. This course is generally provided at
the top of a compound wall or a parapet wall and
it is suitably weathered and threaded as shown
in Fig.1.3.
Coping

String

Fig. 1.3: Coping Fig. 1.4: String course

• String course is the horizontal course provided

at suitable levels between the plinth and cornice.
It breaks the monotony of a plane surface and
is sometimes moulded and given architectural
treatment (Fig.1.4).
• Through stone is set with its longest dimension
perpendicular to the face of the wall and whose
length is equal to the thickness of the wall (Fig.1.5).
Through stone should be strong and of sufficient
thickness so as to avoid the danger of fracture due
to any slight settlement of the wall. Fig. 1.5: Through Stone

Stone Masonry

Unit 1.indd 3 12/2/2020 12:36:06 PM

 Classification of Stone Masonry
Based on the arrangement of the stone in the
construction and degree of refinement in the surface
finish, stone masonry can be classified into the following
two categories:
1. Rubble Masonry
2. Ashlar Masonry

Rubble Masonry
In construction, rubble masonry stones of irregular sizes
are used. The stones as obtained from the quarry are
used as they are or are broken and shaped to suitable
sizes by means of a hammer as the work progresses. The
strength of rubble masonry depends upon the following
three factors:
(i) The quality of mortar
(ii) The use of long through stones at frequent intervals
(iii) The proper filling of mortar in the space between
stones
Rubble masonry is further classified into the following
categories.
• Coursed rubble
• Uncoursed rubble
• Random rubble
• Dry rubble
• Polygonal rubble
• Flint rubble
(a) Coursed rubble is commonly used in the
construction of low height walls of public
buildings, residential buildings, abutment and
piers of ordinary bridges (Fig. 1.6). In this type of
masonry, the height of stones varies from 5 mm
to 200 mm. The masonry work is carried out in a
manner that the height of the stones in a particular
course remains the same. Coursed rubble
masonry is further divided into three categories.
Fig1.6 Coursed rubble masonry (i) Coursed rubble masonry class I: in this type,
stones of the same height are used and the
courses are also of the same height (see Fig 1.7).

Assistant Mason – Class X

Unit 1.indd 4 12/2/2020 12:36:06 PM

 (ii) Coursed rubble masonry class II: this type is
similar to class I, except in the following (Fig 1.8):
• The stones to be used are of different
heights.
• The courses need not be of equal height.
• Only two stones are to be used to make up
the height of one course.
• The thickness of mortar joint is 12 mm.

Fig. 1.7: Coursed rubble masonry Class I Fig. 1.8: Coursed rubble masonry Class II

(iii) Coursed rubble masonry class III: this sort is

similar to class I except in the following:
• The stones to be used are of different height,
the minimum being 50 mm.
• The courses need not be of equal height.
• Only three stones are to be used to make
up the height of one course.
• The thickness of the mortar joint is 16 mm.
(b) Uncoursed rubble masonry: in this type of
rubble masonry, the stones are used in the
same shape as they are obtained from the
quarry except knocking out some coarseness. Fig. 1.9: Uncoursed rubble
The courses are not maintained regularly. The masonry
larger stones are laid first and spaces between
them are then filled with spall (crushed stone)
as shown in Fig. 1.9. The wall is brought to a
level at every 30 cm to 50 cm.
This type of rubble masonry
being cheaper is used for the
construction of compound walls,
godowns, garages, etc.
(c) Random rubble masonry: stones
of irregular sizes and shapes
are used in this type of rubble Fig. 1.10: Random rubble masonry

Stone Masonry

Unit 1.indd 5 12/2/2020 12:36:07 PM

 masonry (Fig.1.10). They are arranged in a
manner to give the structure a good appearance.
(d) Dry rubble masonry: this is just similar in
construction to coursed rubble masonry except
that no mortar is used in the joints (Fig. 1.11).
Although the cheapest, it requires more skill
during construction. It is extensively used
for compound walls on bridge approaches,
retaining walls, etc. Sometimes, to prevent the
Fig. 1.11: Dry rubble masonry displacement of stones, two courses on the
top and about 50 cm length at the ends are
built in mortar.
(e) Polygonal rubble masonry: the stones are
hammer-dressed in this type of rubble masonry
and the stones selected for the facade are
dressed in an irregular polygonal shape.
Thus, the face joints run irregularly in all
directions. This type of masonry requires more
skill (Fig. 1.12).
Fig. 1.12: Polygonal rubble (f) Flint rubble masonry: in this type of masonry,
masonry the stones used are flints. Flint stones varying in
thickness from 8 to 15 cm and 15 to 30 cm in
length are arranged for making a façade in the
form of coursed or uncoursed masonry. In coastal
areas, rounded flints procured from beaches are
used. The joints of flint rubble masonry are raked
back slightly with a pointed stick to improve the
appearance (Fig. 1.13).

Coursed

Lacing Course

IT 02 m
Uncoursed

Lacing course

Fig. 1.13: Flint rubble masonry

Ashlar Masonry
This is a superior quality of masonry and is built from
Fig. 1.14: Ashlar masonry accurately dressed stones with uniform and very fine

Assistant Mason – Class X

Unit 1.indd 6 12/2/2020 12:36:11 PM

 joints (Fig. 1.14). The various types of Ashlar masonry
can be classified under the following categories.
• Ashlar fine
• Ashlar rough-tooled
• Ashlar rock quarry-faced
• Ashlar chamfered
• Ashlar facing
• Ashlar block in course
(a) Ashlar fine: all the bed joints and face stones
should be dressed perfectly so that they conform Fig. 1.15: Ashlar fine

to a desired pattern (Fig. 1.15). The stones

should be arranged in a proper bond and the
thickness of the mortar joint should not exceed
3 mm. This gives a perfectly smooth appearance
but the cost of construction is high.
(b) Ashlar rough-tooled: the size of the stone
bonds, etc., are similar in specification as
described in the case of Ashlar fine masonry.
The exposed portion of this masonry should be
given a fine dressed, chisel drafting of about 25
mm in width. The thickness of mortar joints Fig. 1.16: Ashlar rough-tooled
should not exceed 6 mm (Fig. 1.16).
(c) Ashlar rock or quarry-faced: in this type of
masonry, the exposed portion of the facing
stones, between the chisel drafting, is left
undressed. However, projections that exceed 8
cm are broken. All other specifications are kept
similar to that of Ashlar rough-tooled masonry.
This type gives the construction a massive
appearance (Fig. 1.17).
(d) Ashlar chamfered: the specifications regarding
Fig. 1.17: Ashlar rock or
size bonds and type of joints are similar to the quarry-faced
ones described above. The exposed edges of
stones are levelled for a depth of about 2.5 cm.
(Fig.1.18).
(e) Ashlar facing: in this type of construction
the façade is constructed in Ashlar masonry
and the rear side may be constructed in brick
masonry, rubble masonry or concrete masonry.
Fig. 1.18: Ashlar chamfered
This composite arrangement is economical. The
height should be more than 200 mm. The façade
stones are either rough-tooled or chamfered.

Stone Masonry

Unit 1.indd 7 12/2/2020 12:36:13 PM

 (f) Ashlar block in course: this type of masonry
occupies an intermediate position between
rubble masonry and Ashlar masonry. The stones
for the façade are generally hammer-dressed
and the thickness of mortar joint should not
exceed 6 mm. This type of construction is used
for heavy engineering works, such as retaining
wall, sea wall, etc.

Joints in Stone Masonry

Broadly, joints in stone masonry can be categorised in
the following types.
• Butt or squared joint
• Rebated or lapped joint
• Tongued and grooved joint
• Tabled joint
• Saddled joint
• Rusticated joint
• Plugged joint
• Dowelled joint
• Cramped joint
(a) Butt or squared joint: this is the most common
joint and is extensively used for ordinary
work. In this type of joint the square surface
of one stone is placed against that of another
Fig. 1.19: Butt or squared joint as shown in Fig. 1.19.
(b) Rebated or lapped joint:
in this joint rebates or laps
are provided. They prevent
the movement of stones. The
length of a rebate depends on
the nature of the work but
it should not be less than
70 mm (Fig.1.20).
(c) Tongued and grooved
Fig. 1.20: Rebated or lapped joint
joint: in this joint, a
projection of one stone fits in the corresponding
depression or groove in the adjacent stone. This
arrangement prevents one stone from sliding
over the other. This is also known as joggle joint.

Assistant Mason – Class X

Unit 1.indd 8 12/2/2020 12:36:13 PM

 (b) Tabled joint: is made in the bed of the stone to
check the lateral movement. This joint is used
for sea walls where lateral pressure is heavy
(Fig. 1.21).
(c) Saddled joint: is rounded off to protect the
joints or cornices and similar surfaces from
rainwater. With the help of this arrangement,
water moving on the weathered surface is Fig. 1.21: Tabled joint
diverted from the joints.
(d) Rusticated joint: in this type of joint, the edges
of the joints are sunk below the plane of the
facade. The different types of rusticated joints
are— channelled joint, vee joint, and vee and Vee Joint Chanelled Joint
channelled joint (Fig.1.22).
(e) Plugged joint: in this type of joint, dovetail-
shaped mortises are provided in the sides of Moulded Vee and
Joint Chhanelled Joint
adjacent stones as shown in Fig. 1.20. When
Fig. 1.22: Rusticated joint
stones are placed in position, molten lead is
poured in the joint, which when cooled, connects
the stones firmly. Cement grout is sometimes
used in place of molten lead. This joint is used
for coping carries, etc. (Fig.1.23).
(f) Dowelled joint: in this type of joint, a hole is
cut into each stone and loose dowels, which Fig. 1.23: Plugged joint
are small pieces of hard stone, slate, gun-metal
brass, bronze or copper. They are inserted and
secured with cement as shown in Fig.1.24. A
dowelled joint can easily be used in place of
joggled joints.

Stone
Dowels

Fig. 1.24: Dowelled joint

(g) Cramped joint: in this type of joint, cramps

are used instead of dowels. Cramps are pieces
of non-corrosive metals, such as gun metal,
copper, etc., and their ends are turned down

Stone Masonry

Unit 1.indd 9 12/2/2020 12:36:14 PM

 Rich Cement Mortar to a depth of about 40 to 50 mm. The
Iran CRAMP
Lead length, width and thickness of the
cramps vary from 20 to 30 cm, 25 to
50 mm; and 5 to 10 mm, respectively.
It prevents the tendency of the joint to
be pulled apart. The cramps are placed
Fig. 1.25: Cramped joint in position, grouted and covered with
cement load or asphalt (Fig.1.25).

Maintenance of Stone Masonry Construction

Stone masonry constructions should be maintained in
respect of the following:
• Stains
• Efflorescence
• Cracks
• Waterproofing
(a) Stains: on stone work can be— (a) iron stains,
(b) copper stains, (c) smoke and fix stains, (d) oil
stains, (e) tobacco stains and (f) ink stains.
Iron stains can be removed by washing
the stained area with a solution of Oxalic acid
mixed in water (1kg of Oxalic acid mixed with
10 litres of water). The stained area is rubbed
with a brush and water after 3 to 4 hours. To
remove dark and deep stains a solution having
one part of sodium citrate mixed with six parts of
water is sprinkled. This surface is then covered
with a thin layer of sodium hydrosulphide. The
surface is washed after an hour.
Copper and bronze stains are removed by
applying ammonium chloride solution (1 part of
ammonium chloride, 4 parts of powdered talc)
with ammonia water.
Smoke and fix stains are treated with
powdered pumice or grit. The surface is rubbed
several times and cleaned.
Oil stains are treated with benzene or
petrol. To remove deep oil stains a mixture
of acetone and amyl acetal is used. A diluted
solution of washing soda and water can also
remove tobacco stains.

Assistant Mason – Class X

10

Unit 1.indd 10 12/2/2020 12:36:15 PM

 Chlorinated lime, or ammonia water can Notes
be used to remove ink stains.
(b) Efflorescence: the stones to be used for masonry
work should be kept saturated with water so that
they may not get discoloured on account of the acid
action. Efflorescence is common with certain type
of stones and can be prevented by proper drainage
of the building.
(c) Cracks: can be both small and large. Small
cracks should be cleaned with a wire brush and
filled with a thick paste of cement mix. Large
cracks should be raked out to get space for the
mortar. For this, an inverted groove of at least
10 mm depth is required. A cement sand mortar
of 1:2 ratio, with less water is applied within
an hour after mixing. Aluminium may also be
added in the mixture to make it a tight fit.
(d) Waterproofing: application of waterproofing
material makes stone masonry free from
efflorescence, dampness, frost action, etc.
Generally, heavy petroleum distillate, fatty oil
or insoluble soap are excellent waterproofing
material. These materials are applied as a
washing coat. They may cause some temporary
discolouration.

Laying of Stone Masonry

The following points should be considered during
construction.
• The stone should be hard, tough and durable.
• The stone should be well watered before use.
• There should be no hollow space inside the wall.
• Through stones (headers) should be used in
successive layers, at 1 m (3' to 5') to 1.5 m apart,
both ways.
• Use artificial header (RCC) in case of more width.
• Care should be taken to secure a mortar bond
throughout the masonry. (Approximately 20 mm,
that is, ¾"). Corner stones are prepared from the
mason’s hammer.

Stone Masonry

11

Unit 1.indd 11 12/2/2020 12:36:15 PM

 Notes • To prevent stones from sliding down, the joints
should not be too smooth.
• The wall should be vertical, that is, in plumb.
• Minimum 12 mm (½") margin should be provided
in the external face of the column and masonry,
to avoid the offset of rubble in plinth masonry
after plaster.
• Old work should be cleaned and watered before
starting any new work on it.
• In case of a compound wall, keep expansion joint
at a 15 m interval.
• Lay some vertical stones in masonry for better
bonding of first and second day’s work or layer of
rubble masonry.
• The curing for masonry should be done for a
minimum of two weeks.
• The through stone should be of a length, which is
at least thrice the depth.
• After proper curing and racking for at least 25
mm (1”) depth, the joints should be pointed.
The bonding material used for masonry are:
(i) Cement mortar
(ii) Lime mortar
(iii) Mud mortar
The thickness of masonry should be:
(i) 10 cm
(ii) 20 cm
(iii) 30 cm
(iv) 40 cm
(v) 50 cm
(vi) 60 cm
The proportion of mortar should be:
(i) Masonry in cement/lime mortar 1:8
(ii) Masonry in cement/lime mortar 1:6
(iii) Masonry in cement/lime mortar 1:4
(iv) Masonry in cement/lime mortar 1:2
(v) 1:8, 1:6, etc., is the volumetric proportion where
1 stands for cement/lime and 8, 6 stands for sand.

Assistant Mason – Class X

12

Unit 1.indd 12 12/2/2020 12:36:15 PM

 Chisel

Measuring Tape
Square

Curing Pipe

Mortar Pan

Bucket Spirit Level Spade

Trowel Line Dori

Hammer
Plumb Bob
Mallet

Fig. 1.26: Tools used in stone masonry

Practical Exercise
1. Students may practice how to dress the stone with
appropriate tools.
2. Students are requested to construct Coursed rubble
masonry as per the drawing given below.

Elevation Section

Plan

Stone Masonry

13

Unit 1.indd 13 12/2/2020 12:36:15 PM

 Notes Check Your Progress
A. Fill in the blanks
1. Stone masonry is constructed with stones and _________.
2. In cramped joint, cramps are used instead of ___________.
3. A butt or squared joint is the most __________ joint and is
extensively used for ________ work.
4. The stones of _______________ sizes and shapes are used
in rubble masonry.
5. Coursed rubble masonry is commonly used in the
________ of low height walls of public buildings, residential
buildings, abutment and piers of ordinary bridges.

B. Multiple choice questions

1. Stone used in work should be ___________.

a) hard
b) durable
c) soft
d) tough
2. Mortar is prepared by mixing ___________.
a) cement
b) sand
c) water
d) All of the above
3. Bottom surface of a door or a window opening is known as
___________.
a) sill
b) corbel
c) cornic
d) coping
4. Small cracks should be cleaned with ___________.
a) paper
b) cloth
c) wire brush
d) None of the above
5. Butt joint is most common joint and is extensively used for
___________.
a) heavy work
b) small work
c) ordinary work
d) None of the above

Assistant Mason – Class X

14

Unit 1.indd 14 12/2/2020 12:36:15 PM

 C. Short answer questions Notes
1. Differentiate between Ashlar masonry and rubble masonry.
2. Explain the construction of a wall in coursed rubble
masonry.
3. Describe the tools used in stone masonry construction
with a sketch.
4. Write a short note on uncoursed rubble masonry.
5. What are the different types of Ashlar masonry? Explain
any one.
6. How is the maintenance of stone masonry construction
carried out?
7. Enlist the types of rubble masonry. Explain any one.

Stone Masonry

15

Unit 1.indd 15 12/2/2020 12:36:15 PM