https://shopservicemanual.

com/product/service-manual-jcb-js115-js130-js131-js145-js160-js180-js190

Foreword
The Operator's Manual

You and others can be killed or seriously injured

if you operate or maintain the machine without
first studying the Operator's Manual. You must
understand and follow the instructions in the
Operator's Manual. If you do not understand
anything, ask your employer or JCB dealer to
explain it.

SERVICE MANUAL Do not operate the machine without an Operator's

Manual, or if there is anything on the machine you
do not understand.

Treat the Operator's Manual as part of the machine.

Keep it clean and in good condition. Replace the
Operator's Manual immediately if it is lost, damaged
or becomes unreadable.

EXCAVATOR
JS115, JS130, JS131, Contents
JS145, JS160, JS180, JS190
01 - Machine

03 - Attachments and Options

EN - 9813/7150 - ISSUE 1 - 04/2016 06 - Body and Framework

09 - Operator Station

12 - Heating, Ventilating and Air-

Conditioning (HVAC)

15 - Engine

18 - Fuel and Exhaust System

21 - Cooling System

27 - Driveline

This manual contains original instructions, verified by 30 - Hydraulic System

the manufacturer (or their authorized representative).
33 - Electrical System

72 - Fasteners and Fixings

Copyright 2016 © JCB SERVICE 75 - Consumable Products
All rights reserved. No part of this publication may
be reproduced, stored in a retrieval system, or 78 - After Sales
transmitted in any form or by any other means,
electronic, mechanical, photocopying or otherwise,
without prior permission from JCB SERVICE.

www.jcb.com
Notes:

9813/7150-1
 Spine Cards

SERVICE MANUAL SERVICE MANUAL

Volume 1 Volume 2

JS115, JS130, JS131, JS115, JS130, JS131,

JS145, JS160, JS180, JS190 JS145, JS160, JS180, JS190
EN 9813/7150 EN 9813/7150

SERVICE MANUAL SERVICE MANUAL

Volume 3 Volume 4

JS115, JS130, JS131, JS115, JS130, JS131,

JS145, JS160, JS180, JS190 JS145, JS160, JS180, JS190
EN 9813/7150 EN 9813/7150

9813/7150-1
Notes:

9813/7150-1
 01 - Machine
Contents Page No.

Acronyms Glossary .................................................................................................................................... 01-2

01-03 Safety
01-03-03 Safety - Yours and Others ............................................................................................... 01-3
01-03-06 Safety Warnings ............................................................................................................... 01-4
01-03-09 General Safety ................................................................................................................. 01-5
01-03-12 Maintenance Safety ......................................................................................................... 01-6
01-03-18 Operating Safety .............................................................................................................. 01-8
01-03-21 Worksite Safety .............................................................................................................. 01-10
01-03-24 Risk Assessment ............................................................................................................ 01-11
01-03-27 Maintenance Positions ................................................................................................... 01-12
01-06 About this Manual
01-06-06 Using the Manual ........................................................................................................... 01-15
01-09 Description
01-09-12 Main Component Locations ........................................................................................... 01-19
01-09-15 Service Point Locations ................................................................................................. 01-20

9813/7150-1
2016-03-31
Acronyms Glossary

ARV Auxiliary Relief Valve

DEF Diesel Exhaust Fluid
FEAD Front End Accessory Drive
MRV Main Relief Valve
PIL Parts Identification List

9813/7150-1
2016-03-31
 01 - Machine
03 - Safety

03 - Safety

Contents Page No.

01-03-03 Safety - Yours and Others ............................................................................................... 01-3

01-03-06 Safety Warnings ............................................................................................................... 01-4
01-03-09 General Safety ................................................................................................................. 01-5
01-03-12 Maintenance Safety ......................................................................................................... 01-6
01-03-18 Operating Safety .............................................................................................................. 01-8
01-03-21 Worksite Safety .............................................................................................................. 01-10
01-03-24 Risk Assessment ............................................................................................................ 01-11
01-03-27 Maintenance Positions ................................................................................................... 01-12

01 - 1 9813/7150-1 01 - 1
Notes:

01 - 2 9813/7150-1 01 - 2
 01 - Machine
03 - Safety
03 - Safety - Yours and Others

03 - Safety - Yours and Others

Introduction

All machinery can be hazardous. When a product

is correctly operated and maintained, it is a safe
product to work with. When it is carelessly operated
or poorly maintained it can become a danger to you
(the operator) and others.

In this manual and on the product you will find

warning messages, read and understand them. They
inform you of potential hazards and how to avoid
them. If you do not fully understand the warning
messages, ask your employer or JCB dealer to
explain them.

Safety is not just a matter of responding to the

warnings. All the time you are working on or with the
product you must be thinking of what hazards there
might be and how to avoid them.

Do not work with the product until you are sure that
you can control it.

Do not start any work until you are sure that you and
those around you will be safe.

If you are not sure of anything, about the product or

the work, ask someone who knows. Do not assume
anything.

Remember:

• Be careful
• Be alert
• Be safe.

01 - 3 9813/7150-1 01 - 3
 01 - Machine
03 - Safety
06 - Safety Warnings

06 - Safety Warnings

Introduction

In this manual and on the product, there are safety

notices. Each notice starts with a signal word. The
signal word meanings are given below.

The signal word 'DANGER' indicates a hazardous

situation which, if not avoided, will result in death or
serious injury.

The signal word 'WARNING' indicates a hazardous

situation which, if not avoided, could result in death
or serious injury.

The signal word 'CAUTION' indicates a hazardous

situation which, if not avoided, could result in minor
or moderate injury.

The signal word 'Notice' indicates a hazardous

situation which, if not avoided, could result in product
damage.

The safety alert system (shown) also helps to identify

important safety messages in this manual and on the
product. When you see this symbol, be alert, your
safety is involved, carefully read the message that
follows, and inform other operators.

Figure 1. The safety alert system

01 - 4 9813/7150-1 01 - 4
 01 - Machine
03 - Safety
09 - General Safety

09 - General Safety Lifting Equipment

You can be injured if you use incorrect or faulty lifting
Introduction equipment. You must identify the weight of the item to
be lifted then choose lifting equipment that is strong
enough and suitable for the job. Make sure that lifting
Training equipment is in good condition and complies with all
To operate the machine safely you must know the local regulations.
machine and have the skill to use it. You must abide Raised Equipment
by all relevant laws, health and safety regulations
that apply to the country you are operating in. The Never walk or work under raised equipment unless
operator's manual instructs you on the machine, its it is supported by a mechanical device. Equipment
controls and its safe operation; it is not a training which is supported only by a hydraulic device can
manual. If you are a new operator, get yourself drop and injure you if the hydraulic system fails
trained in the skills of using a machine before trying or if the control is operated (even with the engine
to work with it. If you don't, you will not do your job stopped).
well, and you will be a danger to yourself and others. Make sure that no-one goes near the machine while
In some markets and for work on certain jobsites you you install or remove the mechanical device.
may be required to have been trained and assessed
in accordance with an operator competence scheme. Raised Machine
Make sure that you and your machine complies Never position yourself or any part of your body
relevant local laws and jobsite requirements - it is under a raised machine which is not correctly
your responsibility. supported. If the machine moves unexpectedly you
Care and Alertness could become trapped and suffer serious injury or be
killed.
All the time you are working with or on the machine,
take care and stay alert. Always be careful. Always Lightning
be alert for hazards. Lightning can kill you. Do not use the machine if there
Clothing is lightning in your area.
You can be injured if you do not wear the correct Machine Modifications
clothing. Loose clothing can get caught in the This machine is manufactured in compliance with
machinery. Keep cuffs fastened. Do not wear a prevailing legislative requirements. It must not be
necktie or scarf. Keep long hair restrained. Remove altered in any way which could affect or invalidate its
rings, watches and personal jewellery. compliance. For advice consult your JCB dealer.
Alcohol and Drugs
It is extremely dangerous to operate machinery when
under the influence of alcohol or drugs. Do not
consume alcoholic drinks or take drugs before or
while operating the machine or attachments. Be
aware of medicines which can cause drowsiness.
Feeling Unwell
Do not attempt to operate the machine if you are
feeling unwell. By doing so you could be a danger to
yourself and those you work with.
Mobile Phones
Switch off your mobile phone before entering an
area with a potentially explosive atmosphere. Sparks
in such an area could cause an explosion or fire
resulting in death or serious injury.
Switch off and do not use your mobile phone when
refuelling the machine.

01 - 5 9813/7150-1 01 - 5
 01 - Machine
03 - Safety
12 - Maintenance Safety

12 - Maintenance Safety Hydraulic Pressure

Hydraulic fluid at system pressure can injure you.
Introduction Before connecting or removing any hydraulic hose,
residual hydraulic pressure trapped in the service
hose line must be vented. Make sure the hose
Raised Machine service line has been vented before connecting or
Never position yourself or any part of your body removing hoses. Make sure the engine cannot be
under a raised machine which is not correctly started while the hoses are open.
supported. If the machine moves unexpectedly you 'O' rings, Seals and Gaskets
could become trapped and suffer serious injury or be
killed. Badly installed, damaged or rotted 'O' rings, seals
and gaskets can cause leakages and possible
Air Conditioning Maintenance accidents. Renew whenever disturbed unless
The air conditioning system is a closed loop system otherwise instructed. Do not use Triochloroethane or
and contains pressurised refrigerant. No part of the paint thinners near 'O' rings and seals.
system should be disconnected until the system Arc Welding
has been discharged by a refrigeration engineer
or a suitably trained person. You can be severely To prevent the possibility of damage to electronic
frostbitten or injured by escaping refrigerant. components, disconnect the battery and the
alternator before arc-welding on the machine or
Compressed Air attached implements.
Compressed air is dangerous. Wear personal If the machine is equipped with sensitive electrical
protective equipment. Never point a compressed air equipment, i.e. amplifier drivers, electronic control
jet at yourself or others. units (ECUs), monitor displays, etc., then disconnect
Springs them before welding. Failure to disconnect the
sensitive electrical equipment could result in
Always wear personal protective equipment when
irreparable damage to these components.
dismantling assemblies containing components
under pressure from springs. This will protect against Parts of the machine are made from cast iron, welds
eye injury from components accidentally flying out. on cast iron can weaken the structure and break. Do
not weld cast iron. Do not connect the welder cable
Metal Splinters
or apply any weld to any part of the engine.
You can be injured by flying metal splinters when
Always connect the welder earth (ground) cable to
driving metal pins in or out. Use a soft faced hammer
the same component that is being welded to avoid
or copper drift to remove and install metal pins.
damage to pivot pins, bearings and bushes. Attach
Always wear personal protective equipment.
the welder earth (ground) cable a distance from the
Communications part being welded no more than 0.6m.
Bad communications can cause accidents. If two Counterweights
or more people are working on the machine, make
Your machine may be installed with counterweights.
sure each is aware of what the others are doing.
They are extremely heavy. Do not attempt to remove
Before starting the engine make sure the others are
them.
clear of the danger areas. Examples of danger areas
are: the rotating blades and belt on the engine, the Accumulators
attachments and linkages, and anywhere beneath or The accumulators contain hydraulic fluid and gas at
behind the machine. People can be killed or injured high pressure. Prior to any work being carried out
if these precautions are not taken. on systems incorporating accumulators, the system
Repairs pressure must be discharged by a JCB dealer, as
the sudden release of the hydraulic fluid or gas may
If your machine does not function correctly in
cause injury.
any way, get it repaired straight away. Neglect of
necessary repairs could result in an accident or affect Hot Components
your health. Do not try to do repairs or any other Touching hot surfaces can burn skin. The engine and
type of maintenance work you do not understand. To machine components will be hot after the unit has
avoid injury and/or damage get the work done by a been running. Allow the engine and components to
specialist engineer. cool before servicing the unit.
Soft Ground
A machine can sink into soft ground. Never work
under a machine on soft ground.

01 - 6 9813/7150-1 01 - 6
 01 - Machine
03 - Safety
12 - Maintenance Safety

Working Under the Machine

Make the machine safe before getting beneath it.
Make sure that any attachments on the machine
are correctly attached. Engage the park brake (if
installed), remove the ignition key, disconnect the
battery. If the machine has wheels use blocks to
prevent unintentional movement.
Lifting the Machine
Under no circumstances must the engine be run with
the transmission in gear and only one driving wheel
jacked clear of the ground, since the wheel on the
ground will move the machine.
Chemicals
Certain seals and gaskets (e.g. crankshaft oil
seal) on JCB machines contain fluoroelastomeric
materials such as Viton®, FluorelTM and
Technoflon®. Fluoroelastomeric materials subjected
to high temperatures can produce highly
corrosive hydrofluoric acid. This acid can severely
burn. New fluoroelastomeric components at
ambient temperature require no special safety
precautions. Used fluoroelastomeric components
whose temperatures have not exceeded 300°C
(571.6°F) require no special safety precautions. If
evidence of decomposition (e.g. charring) is found,
refer to the next paragraph for safety instructions.
Do not touch component or surrounding area.
Used fluoroelastomeric components subjected to
temperatures greater than 300°C (571.6°F) (e.g.
engine fire) must be treated using the following
safety procedure. Make sure that heavy duty gloves
and special safety glasses are worn: Thoroughly
wash contaminated area with 10% calcium hydroxide
or other suitable alkali solution, if necessary use
wire wool to remove burnt remains. Thoroughly
wash contaminated area with detergent and water.
Contain all removed material, gloves etc. used in this
operation in sealed plastic bags and dispose of in
accordance with Local Authority Regulations. Do not
burn fluoroelastiometric materials.
Hydraulic Hoses
Never re-use hydraulic hose end crimps or use
reusable hose end crimps.
Personal Protective Equipment
Use the appropriate personal protective equipment
before performing maintenance on the machine,
otherwise you could be injured.
Working at Height
Use appropriate access equipment such as ladders
or a working platform if it is necessary to work at
height to perform maintenance tasks on the machine.
If you do not use suitable access equipment there is
a risk of falling, resulting in personal injury.

01 - 7 9813/7150-1 01 - 7
 01 - Machine
03 - Safety
18 - Operating Safety

18 - Operating Safety Worksites

Worksites can be hazardous. Examine the site
Introduction before working on it. You could be killed or injured
if the ground gives way under your machine or if
piled material collapses onto it. Check for potholes
Training and hidden debris, logs, ironwork etc. Any of these
Make sure that you have had adequate training and could cause you to lose control of your machine.
that you are confident in your ability to operate the Check for utilities such as electric cables (overhead
machine safely before you use it. Practice using the and underground), gas and water pipes etc. Mark
machine and its attachments until you are completely the positions of the underground cables and pipes.
familiar with the controls and what they do. With Make sure that you have enough clearance beneath
a careful, well trained and experienced operator, overhead cables and structures.
your machine is a safe and efficient machine. With Communications
an inexperienced or careless operator, it can be
dangerous. Do not put your life, or the lives of others, Bad communications can cause accidents. Keep
at risk by using the machine irresponsibly. Before you people around you informed of what you will be
start to work, tell your colleagues what you will be doing. If you will be working with other people,
doing and where you will be working. On a busy site, make sure any hand signals that may be used are
use a signalman. understood by everybody. Worksites can be noisy, do
not rely on spoken commands.
Before doing any job not covered in this manual, find
out the correct procedure. Your local JCB distributor Parking
will be glad to advise you. An incorrectly parked machine can move without an
Fuel operator. Follow the instructions in the Operator's
Manual to park the machine correctly.
Fuel is flammable, keep naked flames away from the
fuel system. Stop the engine immediately if a fuel Banks and Trenches
leak is suspected. Do not smoke while refuelling or Banked material and trenches can collapse. Do not
working on the fuel system. Do not refuel with the work or drive too close to banks and trenches where
engine running. Completely wipe off any spilt fuel there is danger of collapse.
which could cause a fire. There could be a fire and
injury if you do not follow these precautions. Safety Barriers
Machine Condition Unguarded machines in public places can be
dangerous. In public places, or where your visibility
A defective machine can injure you or others. Do not is reduced, place barriers around the work area to
operate a machine which is defective or has missing keep people away.
parts. Make sure the maintenance procedures in this
manual are completed before using the machine. Sparks
Machine Limits Explosions and fire can be caused by sparks from
the exhaust or the electrical system. Do not use the
Operating the machine beyond its design limits can machine in closed areas where there is flammable
damage the machine, it can also be dangerous. material, vapour or dust.
Do not operate the machine outside its limits. Do
not try to upgrade the machine performance with Hazardous Atmospheres
unapproved modifications. This machine is designed for use in normal out
Engine/Steering Failure door atmospheric conditions. It must not be used
in an enclosed area without adequate ventilation.
If the engine or steering fails, stop the machine as Do not use the machine in a potentially explosive
quickly as possible. Do not operate the machine until atmosphere, i.e. combustible vapours, gas or dust,
the fault has been corrected. without first consulting your JCB dealer.
Exhaust Gases Regulations
Machine exhaust gases can harm and possibly kill Obey all laws, worksite and local regulations which
you or bystanders if they are inhaled. Do not operate affect you and your machine.
the machine in closed spaces without making sure
there is good ventilation. If possible, install an
exhaust extractor. If you begin to feel drowsy, stop
the machine at once and get into fresh air.

01 - 8 9813/7150-1 01 - 8
 01 - Machine
03 - Safety
18 - Operating Safety

Electrical Power Cables Hands and Feet

You could be electrocuted or badly burned if you get Keep your hands and feet inside the machine.
the machine or its attachments too close to electrical When using the machine, keep your hands and feet
power cables. clear of moving parts. Keep your hands and feet
You are strongly advised to make sure that the safety within the operator compartment while the vehicle is
arrangements on site comply with the local laws in motion.
and regulations concerning work near electric power Controls
lines.
You or others can be killed or seriously injured
Before you start using the machine, check with your if you operate the control levers from outside the
electricity supplier if there are any buried power machine. Operate the control levers only when you
cables on the site. are correctly seated.
There is a minimum clearance required for working Passengers
beneath overhead power cables. You must obtain
details from your local electricity supplier. Passengers in or on the machine can cause
accidents. Do not carry passengers.
Working Platform
Fires
Using the machine as a working platform is
hazardous. You can fall off and be killed or injured. If your machine is equipped with a fire extinguisher,
Never use the machine as a working platform make sure it is checked regularly. Keep it in the
unless with approved man-basket or man-crate (if correct machine location until you need to use it.
applicable). Do not use water to put out a machine fire, you could
Machine Safety spread an oil fire or get a shock from an electrical
fire. Use carbon dioxide, dry chemical or foam
Stop work at once if a fault develops. Abnormal extinguishers. Contact your nearest fire department
sounds and smells can be signs of trouble. Examine as quickly as possible. Firefighters must use self-
and repair before resuming work. contained breathing apparatus.
Hot Components Roll Over Protection
Touching hot surfaces can burn skin. The engine and If the machine starts to roll over, you can be crushed
machine components will be hot after the unit has if you try to leave the cab. If the machine starts to roll
been running. Allow the engine and components to over, do not try and jump from the cab. Stay in the
cool before servicing the unit. cab, with your seat belt fastened.
Travelling at High Speeds Confined Areas
Travelling at high speeds can cause accidents. Pay extra attention to proximity hazards when
Always travel at a safe speed to suit working operating in confined areas. Proximity hazards
conditions. include buildings, traffic and bystanders.
Hillsides Safe Working Loads
Operating the machine on hillsides can be Overloading the machine can damage it and make it
dangerous if the correct precautions are not taken. unstable. Study the specifications in the Operator's
Ground conditions can be changed by rain, snow, ice Manual before using the machine.
etc. Check the site carefully. When applicable, keep
all attachments low to the ground. Lightning
Visibility If you are inside the machine during a lightning storm
stay in the machine until the storm has passed. If
Accidents can be caused by working in poor visibility. you are outside of the machine during a lightning
Use your lights to improve visibility. Keep the road storm stay away from the machine until the storm
lights, windows and mirrors clean. has passed. Do not attempt to mount or enter the
Do not operate the machine if you cannot see clearly. machine.
Modification of the machine's configuration by the If the machine is struck by lightning do not use the
user (e.g. the fitting of large and non-approved machine until it has been checked for damage and
attachments) may result in a restriction of the malfunction by trained personnel.
machine visibility.

01 - 9 9813/7150-1 01 - 9
 01 - Machine
03 - Safety
21 - Worksite Safety

21 - Worksite Safety An applicable worksite organisation is required in

order to minimise hazards that are caused by
restricted visibility. The worksite organisation is a
Introduction collection of rules and procedures that coordinates
the machines and people that work together in
WARNING You or others can be killed or seriously the same area. Examples of worksite organisation
injured if you do unfamiliar operations without first include:
practising them. Practise away from the worksite
on a clear area. Keep other people away. Do not • Restricted areas
perform new operations until you are sure you can • Controlled patterns of machine movement
do them safely. • A system of communication.
WARNING There could be dangerous materials
such as asbestos, poisonous chemicals or other You and/or your company could be legally liable for
harmful substances buried on the site. If you any damage you may cause to public utilities. It is
uncover any containers or you see any signs of your responsibility to make sure that you know the
toxic waste, stop the machine and advise the site locations of any public utility cables or pipes on the
manager immediately. worksite which could be damaged by your machine.
WARNING Before you start using the machine,
check with your local gas company if there are
any buried gas pipes on the site.
If there are buried gas pipes we recommend that
you ask the gas company for any specific advice
regarding the way you must work on the site.
Some modern gas pipes cannot be detected by
metal detectors, so it is essential that an accurate
map of buried gas pipes is obtained before any
excavation work commences.
Hand dig trial holes to obtain precise pipe
locations. Any cast iron pipes found must be
assumed to be gas pipes until contrary evidence
is obtained.
Older gas pipes can be damaged by heavy
vehicles driving over the ground above them.
Leaking gas is highly explosive.
If a gas leak is suspected, contact the local gas
company immediately and warn all personnel on
the site. Ban smoking, make sure that all naked
lights are extinguished and switch off any engines
which may be running.
You are strongly advised to make sure that the
safety arrangements on site comply with the local
laws and regulations concerning work near buried
gas pipes.
CAUTION Before you start using the machine,
check with your local public water supplier if there
are buried pipes and drains on the site. If there
are, obtain a map of their locations and follow the
advice given by the water supplier.
You are strongly advised to make sure that the
safety arrangements on site comply with the local
laws and regulations concerning work near buried
pipes and drains.
CAUTION If you cut through a fibre optic cable,
Do not look into the end of it, your eyes could be
permanently damaged.

01 - 10 9813/7150-1 01 - 10
 01 - Machine
03 - Safety
24 - Risk Assessment

24 - Risk Assessment Loading/Unloading Area

• Is it level? Any slope of more than 2.5% (1 in
Introduction 40) must be carefully considered.
• Is more than one direction of approach to the
load possible? Approaching across the slope
It is the responsibility of the competent people that must be avoided, if possible.
plan the work and operate the machine to make a • Is the ground solid? Will it support the weight of
judgement about the safe use of the machine, they the machine when loaded?
must take into account the specific application and • How rough is the ground? Are there any
conditions of use at the time. sharp projections which could cause damage,
particularly to the tyres?
It is essential that a risk assessment of the work to be • Are there any obstacles or hazards in the area,
done is completed and that the operator obeys any for example, debris, excavations, manhole
safety precautions that the assessment identifies. covers, power lines?
• Is the space sufficient for safe manoeuvring?
If you are unsure of the suitability of the machine for • Are any other machines or persons likely to be
a specific task, contact your JCB dealer who will be in or to enter the area while operations are in
pleased to advise you. progress?
The following considerations are intended as
suggestions of some of the factors to be taken into The Route to be Travelled
account when a risk assessment is made. Other • How solid is the ground, will it provide sufficient
factors may need to be considered. traction and braking? Soft ground will affect the
stability of the machine and this must be taken
A good risk assessment depends on the training and into account.
experience of the operator. Do not put your life or the • How steep are any slopes, up/down/across?
lives of others at risk. A cross slope is particularly hazardous, is it
possible to detour to avoid them?
Personnel
• Are all persons who will take part in the Weather
operation sufficiently trained, experienced and • How windy is it? High wind will adversely affect
competent? Are they fit and sufficiently rested? the stability of a loaded machine, particularly if
A sick or tired operator is a dangerous operator. the load is bulky.
• Is supervision needed? Is the supervisor • Is it raining or is rain likely? The ground that
sufficiently trained and experienced? was solid and smooth when dry will become
• As well as the machine operator, are any uneven and slippery when wet, and it will not
assistants or lookouts needed? give the same conditions for traction, steering
or braking.
The Machine
• Is it in good working order?
• Have any reported defects been corrected?
• Have the daily checks been carried out?
• Are the tyres still at the correct pressure and
in good condition and is there sufficient fuel to
complete the job (if applicable)?

The Load
• How heavy is it? Is it within the capabilities of
the machine?
• How bulky is it? The greater the surface area,
the more affected it will be by wind speeds.
• Is it an awkward shape? How is the weight
distributed? Uneven loads are more difficult to
handle.
• Is there a possibility of the load shifting while
being moved?

01 - 11 9813/7150-1 01 - 11
 01 - Machine
03 - Safety
27 - Maintenance Positions

27 - Maintenance Positions

Introduction

Maintenance Position (Excavator Arm 2. If applicable, lower the dozer blade.

Lowered) 3. Lower the excavator so the dipper is flat on the
1. Park the machine on solid, level ground, with the ground.
upper structure parallel to the undercarriage.

Figure 2.

A Excavator lowered with the dipper flat on the

ground

4. Stop the engine.

5. Remove the ignition key.
6. Discharge the hydraulic pressure. Refer to PIL
(30-00-00).
7. Isolate the battery to prevent the accidental
operation of the engine.

01 - 12 9813/7150-1 01 - 12
 https://shopservicemanual.com/

https://shopservicemanual.com/product/service-manual-jcb-js115-js130-js131-js145-js160-js180-js190