Bell 672G Grader
Bell 672G Grader
Bell 672G Grader
672G GRADER
672G
Technical Documentation
BELL EQUIPMENT COMPANY
Richards Bay
Due to BELL EQUIPMENT’s policy of continuous product improvement, the information contained in this
manual was correct up to the time of printing (issue date of manual). Any changes after this date will only be
included in the next update of this manual.
The illustrations in this manual are pictorial and not necessarily true representations of components.
Photographs and graphics may show optional equipment.
This manual has been produced to assist you in ordering of parts for the maintenance of your BELL
EQUIPMENT machine.
The information contained in the manual is in a logical sequence. Each illustrated breakdown is supported
with a parts list.
The parts manual has been produced by the Technical Documentation Department of BELL EQUIPMENT
Co. Every effort has been made to ensure that the information in this manual was correct at the time of
publication. BELL EQUIPMENT Co. has a policy of continuous product development, improvement and
design. BELL EQUIPMENT Co. reserves the right to change, amend and update the design of its product at
any time without prior notice. With this policy, changes may have occurred that are not included in this
manual.
Whilst every endeavour has been made to provide accurate and reliable information, BELL EQUIPMENT
Co. specifically disclaims any actual or implied warranty and under no circumstances shall be liable for any
loss, damage or injury to person or property suffered, whether direct, or indirect or consequential, arising
from the use of this manual. In particular and without detracting from the above, the disclaimer also applies
in the event of any specification, warning, or representation contained in this manual being inadequate,
inaccurate, or unintentionally misleading.
The user is urged to strictly comply with the instructions and warnings that are given in the interests of
general safety. Please do not hesitate to contact your BELL EQUIPMENT Product Support Representative
whenever you have a query on your BELL product or this manual. The address of your nearest BELL
EQUIPMENT branch or dealer is as follows:-
LOCATION OF OPERATIONS
ASIA PACIFIC:
SINGAPORE
Bell Equipment (SEA) PTE Ltd
Physical Address: 10 Anson Road, #22-02A International Plaza, Singapore, 079903
Contact: Mohd Johari Ahmead (Dealer Development Sales Manager)
Mobile: +65 966 36404
Tel : +65 622 08 004 or +65 622 62 362
Fax :+65 622 03 004E-mail: [email protected] (Johari) or [email protected]
EUROPE :
FRANCE
Bell France SARL
Physical Address: Route d’ Argenton-Sur-Creuse, 23800 Dun Le Palestel, France
Contact: Claude Boulet (Director) Vincent Valadas (Technical Director)
Mobile: +33 60719 5407
Tel : +33 55589 2356
Fax :+33 55589 2324
E-mail: [email protected]
GERMANY
BELL EQUIPMENT (ALSFELD) GMBH
Physical Address: Willi-Brandt Strasse 4-6, D-36304, Alsfeld, Germany
Contact: Andre Krings (Managing Director)
Mobile: +49 176 220 024 416
Tel: +49 6631 911 300
Fax: +49 6631 911 313
E-mail: [email protected]
SPAIN
Bell Equipment Spain
Physical Address: C/Iplacea Nº 10, Nave 2.2 P.I. Alcala Park, 28803 Alcalá de Henares, Madrid, Spain
Contact: Jesus Vivero
Mobile: +34-64 99 33 089
Tel: +34 91 879 60 19
Fax: +34 91 879 60 49
E-mail: [email protected]
SWITZERLAND
Bell Switzerland (Bell Handling Systems and Bellinter Holdings)
Physical Address: Rue de Vevey 178, 1630 Bulle, SWITZERLAND
Contact: Jean-Christophe Cerouter or Pascal Gross
Tel: +41 26 913 00 11/2
Fax: +41 26 913 00 19
E-mail: [email protected] or [email protected]
UNITED KINGDOM
Bell Equipment U.K. LIMITED
Physical Address: Unit 6C, Graycar Business Park, Barton Turns, Barton-Under-Needwood, Burton-on-Trent,
DE13 8EN, UNITED KINGDOM
Contact: Neville Paynter
Tel: +44 1283 714259 (Direct)
Tel: +44 1283 714251 (Parts Direct)
Fax: +44 1283 712687
E-mail: [email protected] or [email protected]
MIDDLE EAST :
KINGDOM OF BAHRAIN
Physical Address: Building 1110, Road 4225, Block 342, Juffair, Manama, Kingdom of Bahrain
CONTACT: KEVIN ROCK (BUSINESS DEVELOPMENT MANAGER)
Mobile: +973 3688 3233
TEL: +973 173 64958
FAX: +973 177 25435
E-MAIL: [email protected]
SOUTHERN AFRICA:
CAPE REGION:
CAPE TOWN
Bell Equipment Sales SA Limited
PHISYCAL ADRESS: 28 AVIATION ROAD, PHASE 4, AIRPORT CITY, CAPE TOWN, 7475
Contact: John Collins (General Manager)
Mobile: +27 (0)82 495 9338
Tel: +27 (0)21 380 9000
Fax: +27 (0)21 380 9057
E-mail: [email protected] [email protected]
EAST LONDON
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 811 EAST COAST RESORT ROAD, MEISIES HALT, GONUBIE, EAST LONDON, 5200
Contact: Kassie van de Heever
Mobile: +27 (0)82 827 8050
Tel: +27 (0)43 732 1415 (Parts) or +27 (0)43 732 1473 (Admin &Technical Queries)
Fax: +27 (0)43 732 1435
E-mail: [email protected]
GEORGE
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: PIONEER AVENUA INDUSTRIA PACALTSDROP, GEORGE, 6534
Contact: Ryan Britain
Mobile: +27 (0)82 334 2170
Tel: +27 (0)44 878 0930/1
Fax: +27 (0)44 878 0932
E-mail: [email protected]
PORT ELIZABETH
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 349 KEMPSTON ROAD, KORSTEN, PORT ELIZABETH, 6056
Contact: Gert Nelson
Mobile: +27 (0)82 657 1190
Tel: +27 (0)41 451 3202/4/6
Fax: +27 (0)41 451 3208
E-mail: [email protected]
NAMIBIA / WINDHOEK
IA Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 37 LAZARETT STREET, AUSSPANN PLATZ, WINDHOEK, NAMIBIA
Contact: Johan van Wyk
Mobile: 081-250 2949
Tel: 264 61 226 021/2/3
Fax: 264 61 228 330
CENTRAL REGION:
JOHANNESBURG (GAUTENG)
Bell Equipment International Operations (Isando Industrial Park)
PHYSICAL ADDRESS: GRIFFITHS ROAD, JET PARK, 1459
Tel: +27 (0)11 966 4949
Fax: +27 (0)11 966 4980
E-mail: [email protected]
MIDDELBURG (MPUMALANGA)
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 9 TSWELOPELE STREET, INDUSTRIAL AREA, MIDDELBURG, 1050
Contact: Aubrey Potgieter
Modile: +27 (0)83 629 1931
Tel: +27 (0)13 246 8900
Fax: +27 (0)13 246 1229
E-mail: [email protected]
TZANEEN (LIMPOPO)
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 1 MANGAAN STREET TZANEEN
Contact: Freddie Barnard (Branch Manager)
Mobile: +27 (0)82 335 9102
Tel: +27 (0)15 307 1129
Fax: +27 (0)15 307 3095
E-mail: [email protected]
COASTAL REGION:
DURBAN
Bell Equipment Group (Chairman’s Office)
PHYSICAL ADDRESS: 75 COLUMBINE PLACE, RING ROAD INDUSTRIAL PARK, DURBAN NORTH, 4000, DURBAN,
4000
Contact: Howard Buttery (Chairman)
Tel: +27 (0)31 569 1100
Fax: +27 (0)31 569 1108
E-mail: [email protected]
EMPANGENI
Bell Equipment Sales SA Limited
Physical Address: No.1 Irvine Bell Drive, Old Mill Industrial, Empangeni, 3880
Contact: Mike Campbell (Branch Manager)
Mobile: +27 (0)82 784 1477
Tel: +27 (0)35 707 2500
Fax: +27(0)35 792 6516
E-mail: [email protected]
NELSPRUIT (MPUMALANGA)
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 3 CHRISTIE CRESCENT, VINTONIA 2, NELSPRUIT,1200
Contact: Leon van der Linde (Acting Branch Manager)
Mobile: +27(0)82 413 2469
Tel: +27 (0)13 755 2110/6
Fax: +27 (0)13 755 2117
E-mail: [email protected]
PIETERMARITZBURG
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 7 VAN ECK PLACE, MKONDENI, SCOTTSVILLE, 3201, PIETERMARITZBURG, 3209
Contact: Les Lothain (Regional Manager)
Mobile: +27 (0)82 774 9937
Tel: +27 (0)33 386 9319
Fax: +27 (0)33 386 1837
E-mail: [email protected]
SWAZILAND
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: TAMBANKULU STREET, PLOT 686, MATSAPHA, SWAZILAND
Contact: Charlie Boucher
Mobile: 00 268 7602 3795
Tel: +268 51 874 96/7
Fax: +268 51 874 98
E-mail: [email protected]
BLOEMFONTEIN
Bell Equipment Sales SA Limited
PHYSICAL ADDRESS: 17 DENNIS POOLEY STREET, BLOEMFONTEIN, 9300
Contact: Peter Wille (Branch Manager)
Mobile: +27 (0)82 854 2265
Tel: +27 (0)51 4327 855
Fax: +27 (0)51 4323 740
E-mail: [email protected] or [email protected]
KIMBERLEY
Bell Equipment Sales SA Limited
PHYSICAL ADDESS: 12 HENDRICK VAN ECK STREET, Kimdustria, 8300
Contact: Aubrey Potgieter (General Manager)
Mobile: +27 (0)83 629 1931
Tel: +27 (0)53 841 0710/11/12/13
Fax: +27 (0)53 841 1940
E-mail: [email protected]
WOLMARANSSTAD
Bell Equipment Sales SA Limited
Physical Address: 80 Kruger Street, Wolmaransstad, 2630
Contact: Bernard Niemand (Branch Manager)
Mobile: +27 (0)82 572 7881
Tel: +27 (0)18 596 2319
Fax: +27 (0)18 596 2855
E-mail: [email protected]
OTHER AFRICA:
ZAMBIA
Bell Equipment Ltd - (Kitwe)
PHYSICAL ADDRESS: KALULUSHI BUSINESS PARK, KALULUSHI, KITWE, ZAMBIA
Contact: Shaunn McCann (Sales Manager)
Mobile: +260 97 770 677
Tel : +260 2 731 557/8
Fax : +260 2 731 555
E-mail: [email protected]
ZIMBABWE
Bell PTA (PVT) Ltd (Harare)
PHYSICAL ADDRESS: 16 ERITH ROAD, WILLOWVALE, HARARE, ZIMBABWE
Contact: Charl du Toit
Mobile: +263-91 260 169
Tel: +263 4 661 061/090/125/181/418
Fax: +263 4 621 026
E-mail: [email protected]
DEALER
IMPORTANT
Due to BELL’s policy of continuous product improvement, the information contained in this manual was
correct up to the time of printing (Issue date of manual). Any changes after this date will be distributed with
associated bulletins. Illustrations in this manual are pictorial representations of the component and are not
drawn to scale.
MACHINE MODEL:
SERIAL NUMBER:
VIN:
PAGE NUMBER:
DID YOU FIND THE INFORMATION EASY TO READ AND UNDERSTAND ? YES NO
NAME:
COMPANY:
TITLE:
ADDRESS:
TELEPHONE NUMBER:
GENERAL INFORMATION
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
LIST OF ABBREVIATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
ORDERING OF PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
BULLETINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MACHINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
MACHINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
MACHINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
MACHINE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
SERVICE KITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
GROUP 0100
WHEELS & TYRES & TRACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
GROUP 0200
AXLES DIFFERENTIALS & SUSPENSION SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
DRIVESHAFT - 0225 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
HFWD PUMP CYLINDER BLOCK, SWASH PLATE & PISTONS - 0261 . . . . . . . . . . . . . . . . . 100
HFWD PUMP END COVER & HFWD MOTOR FLUSHING PUMP - 0261. . . . . . . . . . . . . . . . . 104
GROUP 0300
TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
GROUP 0400
ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
FRONT PLATE AND IDLE GEARS (UPPER AND LOWER) - 0400 . . . . . . . . . . . . . . . . . . . . 236
GROUP 0500
ENGINE AUXILIARY SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
GROUP 0900
STEERING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
GROUP 1000
SERVICE BRAKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409
GROUP 1300
MISCELLANEOUS VEHICLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
GROUP 1600
VEHICLE ELECTRICAL SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
REAR, MID-FRAME AND UNDER FRAME CAB WORK LIGHTS - 1673 . . . . . . . . . . . . . . . . . 436
GROUP 1700
FRAME, CHASSIS OR SUPPORTING STRUCTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . 533
GROUP 1800
OPERATOR'S STATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547
LOW PROFILE CAB WITH DOORS, AND FIXED WINDOWS - 1811 . . . . . . . . . . . . . . . . . . . 548
HEATER & A/C FILTER, FILTER HOUSING & COVER - 1831 . . . . . . . . . . . . . . . . . . . . . . 604
GROUP 1900
SHEET METAL AND STYLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 619
GROUP 2000
SAFETY, CONVENIENCE AND MISCELLANEOUS . . . . . . . . . . . . . . . . . . . . . . . . . . . 633
GROUP 2100
VEHICLE MAIN HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 647
RIGHT MAIN HYD CONTROL VALVE INLET & OUTLET SECT - 2162 . . . . . . . . . . . . . . . . . . 676
LEFT MAIN HYD CONTROL VALVE INLET & OUTLET SECT - 2162. . . . . . . . . . . . . . . . . . . 678
ONE HAND BLADE LIFT CONTROL LEVER AND VALVE KIT - 2162 . . . . . . . . . . . . . . . . . . 690
GROUP 3400
GRADING DEVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 707
14` X 24" X 7/8" MOLDBOARD (5/8" X 8" CUTTING EDGES) - 3401 . . . . . . . . . . . . . . . . . . . 708
BLADE TILT & SIDE SHIFT HYD HOSES (STD CONTROLS) - 3460 . . . . . . . . . . . . . . . . . . . 744
GROUP 4200
GROUND CONDITIONING TOOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 769
To facilitate the ordering of parts, the following information is required to determine the correct part for your
BELL product.
3. The section, page and item where the part appears in the parts manual.
Any other information which will assist us in getting the parts to you with the least amount of trouble or delay
should be given. This information will be noted and filed for future reference.
Record the relevant information from the Technical Documentation Bulletins, Service Bulletins and Parts
Bulletins into this manual as follows:
I. Ensure the manual number (87xxxxx) reflected in the bulletin is the same as the 87xxxxx
INSERTED BY
BULLETIN NO. DATE RECEIVED SIGNATURE
NAME
INSERT BY
BULLETIN NO. DATE RECEIVED SIGNATURE
NAME
EACH MOTOR GRADER MAY HAVE FIVE SERIAL NUMBER PLATES: ONE FOR THE PRODUCT
IDENTIFICATION NUMBER, ONE FOR THE ENGINE, ONE FOR THE TRANSMISSION, ONE FOR THE
HYDRAULIC PUMP AND ONE FOR THE DIFFERENTIAL.
THE ENGINE SERIAL NUMBER PLATE IS LOCATED ON THE LEFT-HAND SIDE OF THE CYLINDER
BLOCK ABOVE THE STARTING MOTOR.
THE TRANSMISSION SERIAL NUMBER PLATE IS LOCATED ON THE LOWER LEFT OF THE
TRANSMISSION HOUSING.
THE HYDRAULIC PUMP SERIAL NUMBER PLATE IS LOCATED ON THE BOTTOM OF THE PUMP.
THE DIFFERENTIAL SERIAL NUMBER PLATE IS LOCATED ON THE COVER, RIGHT LOWER, BELOW
THE DRIVE SHAFT INPUT.
SERIAL NUMBER INFORMATION IS LISTED TO SHOW ON WHICH MACHINES EACH PART CAN BE
USED; FOR EXAMPLE:
DIRECTION ARROW
ARROWS ARE USED WITH ILLUSTRATIONS TO INDICATE THE FRONT OF THE UNIT. "RIGHT-HAND"
AND "LEFTHAND" SIDES ARE DETERMINED BY FACING IN THE DIRECTION OF MACHINE FORWARD
TRAVEL.
BOX-ENCLOSED ILLUSTRATIONS
A KEY NUMBER, SHOWN IN THE PARTS LIST, IS ASSIGNED TO A BOX ENCLOSING ALL PARTS
SOLD AS A SERVICE ASSEMBLY.
COMPLETE GOODS ARE LISTED IN BOLD FACE TYPE. ORDER SEPARATELY. DO NOT INCLUDE ON
REPLACEMENT PARTS ORDER.
SI UNITS OF MEASURE
METRIC DIMENSIONS ARE GIVEN, WHERE APPLICABLE, THROUGHOUT THIS PARTS CATALOG.
REMARKS AND ABBREVIATIONS MAY APPEAR THROUGHOUT THE PARTS CATALOG. REFER TO
THE FOLLOWING CHARTS FOR TRANSLATIONS TO LANGUAGES OTHER THAN ENGLISH.
NOTE: Specifications and design subject to change without notice. Wherever applicable, specifications are
in accordance with SAE standards. Except where otherwise noted, these specifications are based on a
machine with 14-24, 12-PR G2 tires, 3.66 m x 610 mm
x 22 mm (12 ft x 24 in x .88 in) moldboard with 152 mm x 16 mm (6 in x 5/8 in) cutting edges, and standard
equipment. Weights include lubricants, coolants, full fuel tank and 79 kg (175 lb) operator.
NOTE: Too much weight may wear power train parts faster than normal and could affect the warranty. Check
your warranty.
672G and 672GP Typical Operating Weights with Front Push Block and Ripper
NOTE: Too much weight may wear power train parts faster than normal and could affect the
warranty. Check your warranty.
Maximum front axle weight and maximum rear axle weight are not permissible on the same machine as
maximum total machine weight will be exceeded. Check with tire manufacturer for recommended maximums
for tire specifications.
672G and 672GP Typical Operating Weights with Front Push Block and Ripper
Maximum front axle weight and maximum rear axle weight are not permissible on the same machine as
maximum total machine weight will be exceeded. Check with tire manufacturer for recommended
maximums for tire specifications
672G and 672GP—9.0L Tier 3/Stage IIIA Engine and 9.0L Stage IIIA Engine
670G, 670GP, 672G, 672 GP, 770G, 770GP, 772G, and 772GP Forward Travel Speeds with No Tire Slip
@ 2180 rpm with 14.0-R24 Tires:
FILTER,ELEMENT RE522878 X X X
FILTER,AIR SECONDARY
AT178517 X X
670D
HYDRAULIC BREATHER
AT101565 X X
FILTER
DRIVESHAFT - 0225
DRIVESHAFT - 0225
HFWD PUMP END COVER & HFWD MOTOR FLUSHING PUMP - 0261
HFWD PUMP END COVER & HFWD MOTOR FLUSHING PUMP - 0261
TRANSMISSION - 0341
TRANSMISSION - 0341
FLYWHEEL - 0400
FLYWHEEL - 0400
THERMOSTAT - 0400
THERMOSTAT - 0400
TURBOCHARGER - 0400
TURBOCHARGER - 0400
SENSORS - 0400
SENSORS - 0400
RE65908PCDA02
RE65165PCDA02
CONTINUED
CONTINUED
9 (PERIODIC MAINTENANCE)
277307 1 DECAL
(NOT ILLUSTRATED)
(STANDARD CONTROLS)
(STANDARD CONTROLS)
HORN - 2004
HORN - 2004
6 1 HYDR.QUICK COUPLER
T208291
SOCKET
7 T176425 3 PLUG
8 ........ 4 SCREW
9 AT305110 1 SEAL KIT
10 T54904 2 UNION FITTING
11 N203952 1 O-RING
12 AT191366 1 BEARING KIT
13 T188686 1 PLATE
14 AT196346 1 KIT (CONTAINS PUMP PISTONS AND HOUSING)
15 T185138 1 DRIVE SHAFT
16 AT280244 1 SWASH PLATE
17 AT191367 1 BEARING KIT
18 AT191369 1 PISTON REPLACEMENT KIT
19 AT191368 2 BEARING
20 ........ 1 PLUG (ORDER AT191371)
21 F37030250 1 O-RING
22 R28782 6 O-RING
23 4001456 1 SLEEVE
24 T185183 1 SEAL
25 T185254 1 SNAP RING
RIGHT MAIN HYD CONTROL VALVE INLET & OUTLET SECT - 2162
RIGHT MAIN HYD CONTROL VALVE INLET & OUTLET SECT - 2162
LEFT MAIN HYD CONTROL VALVE INLET & OUTLET SECT - 2162
LEFT MAIN HYD CONTROL VALVE INLET & OUTLET SECT - 2162
ONE HAND BLADE LIFT CONTROL LEVER AND VALVE KIT - 2162
ONE HAND BLADE LIFT CONTROL LEVER AND VALVE KIT - 2162
2 1 (INCLUDES AT307045)
AT302906 FILTER HEAD
(ALSO ORDER AT367840) ITEM 5
AT307045 1 PRESSURE SWITCH (INCLUDES P46051)
P46051 1 O-RING
3 AT306111 1 FITTING
4 R26448 1 O-RING
5 AT367840 1 OIL FILTER (SUB FOR AT308274, THIS APPLICATION)
(5/8" HARDWARE)
(5/8" HARDWARE)
(5/8" HARDWARE)
(5/8" HARDWARE)
(FIELD KIT)
(FIELD KIT)
BLADE TILT & SIDE SHIFT HYD HOSES (STD CONTROLS) - 3460
BLADE TILT & SIDE SHIFT HYD HOSES (STD CONTROLS) - 3460
18 1 (RIPPER/REAR SCARIFIER
AT318529 KIT
PLUMBING) (WHOLEGOODS)
CYLINDER - 4265
CYLINDER - 4265