EL Monobond

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

EL-MONOBOND®

Two Component Non Re-emulsifiable Epoxy Latex System

EL–Monobond® is a two component non re- For bonding applications mix part A and part B in
emulsifiable epoxy latex system which can be equal proportion by volume stir thoroughly to get
used for plain and cement modified coating a uniform mix and apply on the surface to be
applications over concrete/plastered substrates. bonded after wetting the surface sprinkling with
little water. Apply the mortar / concrete within
TYPICAL APPLICATIONS half an hour.
• Excellent bonding agent between New and
Old concrete. TECHNICAL DATA
• As waterproof, water resistant anti-
carbonation coating over concrete. Base Non Re-emulsifiable Epoxy Latex
• Ideal for coating and crack filling of concrete System Twin Pack
surfaces like terraces, roofs, basements,
sunken slabs, liftpits, bridge decks, soffits, Mix Proportion: Bonding
inside/outside surface of PSC box girders, Part–A 500 ml
marine structures like jetties, walls etc. Part-B 500 ml
Cement 1000 gm
UNIQUE ADVANTAGES Water 500 ml
Excellent bonding agent between New and Old
concrete. 2-3 m2 / lt of mix
Coverage
(Depending on Substrate)
It can be applied over moist surface also.
EL–Monobond® cementitious coatings are stable, Coating
waterproof, impermeable even in presence of Part-A 1000 ml
water and compatible with cementitious substrate. Part-B 1000 ml
Conforms to ASTM-C-1059-86 Type II Cement 3000 gms
Water 2000 ml
APPLICATION PROCEDURE
EL–Monobond® system is brush applied and the
3-4 m2 / lt. of mix
substrate before application shall be free from Coverage
(Depending on Substrate)
loose particles, grease, etc. Thorough cleaning
with water after abrading with wire brush prior to Pot Life 1 hr. for 1 lt. mix
application is carried out. Shelf Life 12 months
Stir vigorously for 5 minutes individual Packing 2 lt, 10 lt, 60 lt
components of Part A & Part B, and mix the two
parts in prescribed proportion thoroughly and add For Crack Filling
cement and clean water (as prescribed) slowly so Part-A 100 PBV
as to form homogenous mix. Stir vigorously for 5 Part-B 100 PBV
minutes and apply. Apply minimum 2 coats for
waterproofing applications.

___________________________________________________________________________________________________________
An ISO 9001-2008 Company
Unit # 2, Bldg. 6, Sect. 3, Millennium Business Park, Mahape, Navi Mumbai- 400 710
Tel: 2778 29 23 / 24 • Fax: 022-2778 2808
e-mail: [email protected] • www.krishnaconchem.com (w.e.f. 1st Feb. 2014)
Storage & Handling:
Store the material in a cool place away from direct sunlight or any source of ignition and fire. Keep away from the reach
of children in a well ventilated place.

Health & Safety Precautions:


Wear protective gloves, goggles, and nose masks while handling and using the material. In case of splashes on the skin
and contact with eyes wash thoroughly with plenty of water. In case of ingestion and inhalation remove the personnel to
fresh air. Seek medical advice in all the above cases. The disposal of excess or spilled material shall be carried out in
accordance with local regulations.
Disclaimer:
This information given in good faith and to best of our knowledge is based on results gained from experience and tests. Whereas Krishna Conchem
Products Pvt. Ltd. (KCPPL) endeavors to ensure that any advice, recommendation specification or information it may give is accurate and correct, it
cannot accept any liability arising from the use of products since the conditions of use are beyond its control whether or not in accordance with any
advice specifications, recommendation or information given by it.

___________________________________________________________________________________________________________
An ISO 9001-2008 Company
Unit # 2, Bldg. 6, Sect. 3, Millennium Business Park, Mahape, Navi Mumbai- 400 710
Tel: 2778 29 23 / 24 • Fax: 022-2778 2808
e-mail: [email protected] • www.krishnaconchem.com (w.e.f. 1st Feb. 2014)

You might also like