Scribd
Upload
3K views4 pages

Manual VCDS - Audi Q3

This document provides coding adjustments for various vehicle settings in three or fewer sentences: It describes coding adjustments to enable features like closing windows and sunroof with remote, independent fog light control, split brake/turn signals, hidden menu access, and automatically folding mirrors upon locking with the remote. The document provides the module location and coding bytes to modify along with instructions for accessing long and adaptation coding.

Uploaded by

Vitor Moreira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views4 pages

Manual VCDS - Audi Q3

This document provides coding adjustments for various vehicle settings in three or fewer sentences: It describes coding adjustments to enable features like closing windows and sunroof with remote, independent fog light control, split brake/turn signals, hidden menu access, and automatically folding mirrors upon locking with the remote. The document provides the module location and coding bytes to modify along with instructions for accessing long and adaptation coding.

Uploaded by

Vitor Moreira
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Use Remote to Close Windows & Sunroof with extended hold on lock button

[09 - Cent. Elec.]


[Coding - 07] -> [Long Coding Helper] -> Byte 3
Bit 5 - Comfort Operation via Remote Control active
Select

Enable Independent Fogs control with high beams

[09 – Cent. Elect.]


[Coding - 07] -> [Long Coding Helper] -> Byte 14
Bit 2 – Uncheck

Cornering Fog Light

[09 – Cent. Elect.]


[Coding - 07] -> [Long Coding Helper] -> Byte 14
Bit 7 - Active

DRLs (LEDs) Remain on During Turn Signal

[09 - Cent. Elect.]


[Coding - 07] -> [Long Coding Helper] -> Byte 15
Bit 3 - Uncheck

Enable Split Brake/Turn Signals in Rear LEDs

[09 - Cent. Elec.]


[Coding - 07] -> [Long Coding Helper] -> Byte18
[Bit 0 - 7] "84 Light Setup : Audi Q3 (8UB) Bi-Xenon (PR8BP/8IH) | LED Tails (PR-8SK) | DRLs (PR-8K4)"
Select

Change Number of Turn Signal Cycles on Comfort

[09 - Cent. Elec.]


[Adaptation - 10] -> [Select from Drop-Down menu] ->
[Comfort Turn Signals (Cycles)] ->
[Channel 31]
Set Value to 2 through 5

Turn Seat Belt Warning Chime Off

[17 - Instruments]
[Coding - 07] -> [Long Coding Helper] -> [Byte 1]
[Bit 1 - Seat Belt Warning active/installed]
UnCheck Box

Enable Gauge Pointer Sweep on Start

[17 - Instruments]
[Adaptation - 10] -> Channel - Staging
Set to "active"

Enable Lap Timer/Oil Temp in DIS

[17 - Instruments]
[Adaptation - 10] -> Channel - Lap counter
Set to "on"

Enable Boost Pressure in LT DIS

[17 - Instruments]
[Adaptation - 10] -> Channel - boost_pressure
Set to "on"

Enable Hidden menu in MMI 3G

[5F - Information Electr.]


[Adaptation - 10] -> [Channel 6]
Change 0 to 1
To access the hidden menu, hold down Car and Menu together for 5 seconds

Disable NAV & Phone warning messages while entering data at speed

[5F - Information Electr.]


[Adaptation - 10] -> [Channel 2 & 3]
Set to 250

Close rear hatch with remote (single press)

[6D - Trunk Elect.]


[security Access - 16] -> code: 12345
[Adaptation - 10]
(3)-Activation using rear lid opening button in remote key-Touch function for closing
not active
(4)-Activation using rear lid opening button in remote key-Tap function for closing
active

Automatically Fold Mirror Upon Locking with Remote or


With HOLD for 4 seconds on Door Sensor :
You MUST code BOTH door controllers or only ONE mirror will fold -

[42 - Door Elect. Driver]


[Coding - 07] -> [Long Coding Helper] -> [Byte 4]
[Bit 6 - Undocumented (1 = active) in Binary String]
=> Change Bit 6 to 1
Note : Bit 0 is at the far right of the binary string
The old HEX value for this byte was prolly 1C; Binary Value [00011100]
and the NEW HEX value should be typed in as 5C; Binary Value [01011100]

Esc or Exit
Transfer Coding
Do It!

[52 - Door Elect. Pass.]


[Coding - 07] -> [Long Coding Helper] -> [Byte 4]
[Bit 6 - Undocumented (1 = active) in Binary String]
=> Change Bit 6 to 1
Note : Bit 0 is at the far right of the binary string
The old HEX value for this byte was prolly 1E; Binary Value [00011110]
and the NEW HEX value should be typed in as 5E; Binary Value [01011110]

Esc or Exit
Transfer Coding
Do It!

You might also like