-|Transparent Guide|-

TCD210202AB Safety Considerations

• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.
• ᜸ symbol indicates caution due to special circumstances in which hazards may occur.

᜸ Warning Failure to follow instructions may result in serious injury or death.

01. Fail-safe device must be installed when using the unit with machinery that may
cause serious injury or substantial economic loss.(e.g. nuclear power control,
medical equipment, ships, vehicles, railways, aircraft, combustion apparatus,
safety equipment, crime/disaster prevention devices, etc.)

HART Protocol Transmitter

Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable/explosive gas, high humidity,
direct sunlight, radiant heat, vibration, impact, or salinity may be present.
Failure to follow this instruction may result in explosion or fire.
03. Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in electric shock.
04. For installing the unit, ground it exclusively and use over AWG11 (4 mm²) ground
cable.
Failure to follow this instruction may result in electric shock.
05. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.
06. Check ‘Connections’ before wiring.
Failure to follow this instruction may result in fire.

᜸ Caution Failure to follow instructions may result in injury or product damage.

01. Use the unit within the rated specifications.

Failure to follow this instruction may result in fire or product damage.
02. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
03. Keep the product away from metal chip, dust, and wire residue which flow into the
unit.
Failure to follow this instruction may result in fire or product damage.

Cautions during Use

• Follow instructions in ‘Cautions during Use’.
Otherwise, it may cause unexpected accidents.
• 10.5 - 45 VDCᜡ Model power supply should be insulated and limited voltage/current or Class
2, SELV power supply device.
• Keep away from high voltage lines or power lines to prevent inductive noise.

KT-502H Series
Do not use near the equipment which generates strong magnetic force or high frequency
noise.
• Install a power switch or circuit breaker in the easily accessible place for supplying or

PRODUCT MANUAL
disconnecting the power.
• The explosion-proof standard of this unit is Ex d IIC T6, protection structure of this unit is IP 67
and the range of max. surface temperature is below 85 ℃.
Use the verified explosion-proof electric connection (cable gland or sealing fitting)
For your safety, read and follow the considerations written in the instruction • This unit may be used in the following environments.
manual, other manuals and Autonics website. - Indoors (in the environment condition rated in ‘Specifications’)
The specifications, dimensions, etc. are subject to change without notice for product - Altitude max. 2,000 m
improvement. Some models may be discontinued without notice. - Pollution degree 2
- Installation Category II
• The explosion-proof unit is certified and the same specifications which is reported
to Korea Gas Safety Corporation. (This unit is manufactured following by the

Features announcement 2013-54 of Ministry of Employment and Labor of Korea.)

• HART protocol
• 330 ° rotatable display for environment conditions
• Increased visibility with backlight function
• Multi-input (order 1 input type among 22 types)
- RTD 8 types
- Thermocouple 8 types
- mV 4 types
- Resistor 2 types
• Explosion class: Ex d IIC T6
• Protection structure: IP67 (IEC standard)

ᜢᜫ
-|Transparent Guide|-

Ordering Information Dimensions

This is only for reference, the actual product does not support all combinations. • Unit: mm, For the detailed drawings, follow the Autonics website.
For selecting the specified model, follow the Autonics website. 83 142

KT - 502H ❶ - ❷
❶ Mounting bracket ❷ Temperature input range

86
96
0: Without bracket Refer to 'Input Specifications'.
1: With bracket 2- (1/2 14NPT)
□ 55

■ With bracket
Specifications 83 215
142
Model KT-502H
Power supply 10.5 - 45 VDCᜡ (with backlight LCD)
Output DC 4-20 mA (2-wire)
Input specifications Refer to 'Input Specifications'

86
96
Accuracy ± 0.3 %
PV display part: 7 segment 5 digit (character size: W4×H8 mm), 2- (1/2 14NPT)
Display method Parameter display part: 14 segment 8 digit

200
(character size: W2.6×H4.8 mm), 52 bar meter
Display range -19,999 to 99,999

(2B Pipe)
DN50
Setting method HART-protocol (no setting key)
Response time 1 sec
Alarm ≤ 3.8 mA, ＞ 20.5 mA / Sensor break 3.6 mA Mounting bracket
Load ≤ (V power supply - 7.5 V) / 0.22 A 94
Galvanic insulation 2 kVACᜠ (Input/Output)
Unit weight
≈ 1.2 kg (≈ 1.4 kg)
(Packaged) Connections
Ambient temp. -20 to 70 ℃, storage: 20 to 80 ℃ (no freezing or condensation) Indicator
Recorder
Ambient humi. 0 to 85 %RH, storage: 0 to 85 %RH (no freezing or condensation) DCS
Controller
Protection structure IP67 (IEC standard)
HART Communicator
Power
Material Body: Aluminum (AlDc.8S), Cover O-Ring: Buna N Supply
Explosion class 01)
Ex d IIC T6 Min. 250 Ω

Approval ᜢᜫ
1 2 3 4 5 6
01) The explosion class specification is acquired and managed by KONICS.

Input Specifications A B b
RTD
- +
Input type Input range (℃) Input range (℉) mV Power supply
+ - 10.5-45 VDCᜡ
K (NiCr-Ni) -270 to 1,372 -454 to 2,501.6
TC
J (Fe-CuNi) -210 to 1,200 -346 to 2,192 + -

E (NiCr-CuNi) -270 to 1,000 -454 to 1,832

T (Cu-CuNi) -270 to 400 -454 to 752
Thermocouple
B (PtRh30-PtRh6) 0 to 1,820 32 to 3,308
Temperature Range Setting
R (PtRh13-Pt) -50 to 1,768 -58 to 3,214.4 • Connect a HART communicator and set temperature range as follows.
S (PtRh10-Pt) -50 to 1,768 -58 to 3,214.4
Online (Generic) ① Press key for 3 sec.
N (NiCrSi-NiSi) -270 to 1,300 -454 to 2,372 1. Device Setup
2. PV Select '4. PV LRV' by using , keys and press key.
Cu50 Ω -50 to 150 -58 to 302 3. PV Ao
Cu100 Ω -50 to 150 -58 to 302 4. PV LRV
5. URV SAVE
DPt100 Ω -200 to 850 -328 to 1,562
1. PV LRV ② Select '1. PV LRV' (Low temp. range) and press key.
DPt500 Ω -200 to 250 -328 to 482 2. URV
RTD
DPt1000 Ω -200 to 250 -328 to 482 HELP HOME
Ni100 Ω -60 to 180 -76 to 356
PV LRV ③ Set Low temp. range and press (F4) key.
Ni500 Ω -60 to 180 -76 to 356 0.000 deg C

Ni1000 Ω -60 to 150 -76 to 302 0.000

0 to 400 Ω HELP DEL ESC ENTER

Resistance transmitter Resistance (Ω) -
0 to 2000 Ω 1. PV LRV ④ Select '2. URV' (High temp. range) and press key.
-10 - 75 mV 2. URV
HELP HOME
-100 - 100 mV
Analog Voltage -
-100 - 500 mV PV URV ⑤ Set High temp. range and press (F4) key.
100.000 deg C
-100 - 2,000 mV 100.000
HELP DEL ESC ENTER

Opening the Cover 1. PV LRV 0.000 deg C ⑥ When the set temperature range is correct, press
2. URV 100.000 deg C (F2) key.
HELP SEND HOME

- WARNING - ⑦ Press (F4) key.

Pressing ' OK ' will
To open the cover, unscrew the M3×6L change device output
headless bolt using a 1.5 hexagon wrench put 100P in manual
and rotate the cover.
- WARNING - ⑧ Press (F4) key.
Return control 100P
To automatic control
OK

1. PV LRV 0.000 deg C ⑨ Check the set temperature range.

2. URV 100.000 deg C Press (F3) key.
HELP HOME HART communication will be off.
-|Transparent Guide|-

Current Trim Setting Segment Table

• Connect a HART communicator and set temperature range as follows. The segments displayed on the product indicate the following meanings. It may differ
depending on the product.
1. Device Setup ① Select '1. Device Setup' by using , keys and press
2. PV
3. PV Ao
key. 7 Segment 11 Segment 12 Segment 16 Segment
4. PV LRV 0 0 I I 0 0 I I 0 0 I I 0 0 I I
5. URV
1 1 J J 1 1 J J 1 1 J J 1 1 J J
1. Process Variables ② Select '2. Diag/Service' by using , keys and press
2. Diag/Service 2 K 2 2 K K 2 K 2 K
key.
2 K 2 K 2 K
3. Basic Setup 3 L 3 3 L L 3 L 3 L
4. Detailed Setup
3 L 3 L 3 L
5. Review 4 4 M M 4 4 M M 4 4 M M 4 4 M M
1. Test device ③ Select '4. D/A trim' by using , keys and press 5 5 N N 5 5 N N 5 5 N N 5 5 N N
2. Loop test 6 O 6 O 6 O 6 O
3. Calibration
key. 6 O 6 O 6 O 6 O
4. D/A trim 7 7 P P 7 7 P P 7 7 P P 7 7 P P
WARN-Loop should be ④ Press (F4) key. 8 8 Q Q 8 8 Q Q 8 8 Q Q 8 8 Q Q
removed from 9 R 9 9 R R 9 R 9 R
automatic control
9 R 9 R 9 R

ABORT O K A A S S A A S S A A S S A A S S
B T B B T T B T B T
⑤ Press (F4) key.
B T B T B T
Connect reference
meter C C U U C C U U C C U U C C U U
ABORT O K D D V V D D V V D D V V D D V V
E W E W E W E W
⑥ Press (F4) key.
E W
Setting fid dev
E W E W E W
output to 4mA F F X X F F X X F F X X F F X X
ABORT O K G G Y Y G G Y Y G G Y Y G G Y Y
Enter meter Value ⑦ Press (F4) key to set 4 mA display value. H H Z Z H H Z Z H H Z Z H H Z Z
4.000
HELP DEL ABORT ENTER

Fid dev output 4.000 ⑧ If output display value is correct, select '1. Yes' and
mA equal to reference press (F4) key. If not, select '2. No' and press
meter ?
1. Yes (F4) key and re-set the display value.
E.g.) If output display value is 3.89mA, select 3.89 and press
2. No ABORT ENTER
(F4) key.
Setting fid dev. ⑨ Press (F4) key.
output to 20mA
ABORT O K

Enter meter Value ⑩ Press (F4) key to set 20 mA display value.

20.000
HELP DEL ABORT ENTER

Fid dev output 20.000 ⑪ If output display value is correct, select '1. Yes' and
mA equal to reference press (F4) key. If not, select '2. No' and press
meter ?
1. Yes (F4) key and re-set the display value.
2. No ABORT ENTER

NOTE-Loop may be ⑫ Press (F4) key.

returned to automatic
control
ABORT OK

Diag/Service ⑬ Press (F3) key.

1. Test device
2. Loop test
3. Calibration
4. D/A trim
HELP SAVE HOME

Device Disconnected ⑭ Press (F3) key.

RETRY QUIT

1. Offline ⑮ Press (F3) key to quit the setting menu.

2. Online
3. Frequency Device
4. Utility

Error
Display Error Troubleshooting
Temperature sensor A, B or all sensors are
ERR05
disconnected Check the temperature
sensor
ERR06 Temperature sensor B is disconnected
When PV is lower than the low-limit value of Check the low-limit value of
set temperature range the set temp. range
ERR07

When PV is higher than the high-limit value of Check the high-limit value
set temperature range of the set temp. range
ERR08

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002

www.autonics.com | +82-2-2048-1577 | [email protected]