TECHNICAL DATA

IW4051B

Analog Multiplexer Demultiplexer

High-Performance Silicon-Gate CMOS
The IW4051B analog multiplexer/demultiplexer is digitally
controlled analog switches having low ON impedance and very low
OFF leakage current. Control of analog signals up to 20V peak-to-
peak can be achieved by digital signal amplitudes of 4.5 to 20V (if VCC
- GND = 3V, a VCC - VEE of up to 13 V can be controlled; for VCC -
VEE level differences above 13V a VCC - GND of at least 4.5V is
required).
These multiplexer circuits dissipate extremely low quiescent power
over the full VCC -GND and VCC - VEE supply-voltage ranges,
independent of the logic state of the control signals. When a logic
“1”is present at the ENABLE input terminal all channels are off. ORDERING INFORMATION
The IW4051B is a single 8-channel multiplexer having three binary IW4051BN Plastic
control inputs, A,B and C, and an ENABLE input. The three binary IW4051BDW SOIC
signals select 1 of 8 channels to be turned on, and connect one of the 8 TA = -55° to 125° C for all packages
inputs to the output.
• Operating Voltage Range: 3.0 to 18 V
• Maximum input current of 1 µA at 18 V over full package-
temperature range; 100 nA at 18 V and 25°C PIN ASSIGNMENT
• Noise margin (over full package temperature range):
1.0 V min @ 5.0 V supply
2.0 V min @ 10.0 V supply
2.5 V min @ 15.0 V supply

LOGIC DIAGRAM
Single-Pole, 8-Position Plus Common Off

FUNCTION TABLE

Control Inputs ON
Enable Select Channels
C B A
L L L L X0
L L L H X1
L L H L X2
L L H H X3
L H L L X4
PIN 16 =VCC L H L H X5
PIN 7 = VEE L H H L X6
PIN 8 = GND L H H H X7
H X X X None
X = don’t care

97
IW4051B

MAXIMUM RATINGS*

Symbol Parameter Value Unit

VCC DC Supply Voltage (Referenced to GND) -0.5 to +20 V
VIN DC Input Voltage (Referenced to GND) -0.5 to VCC +0.5 V
VOUT DC Output Voltage (Referenced to GND) -0.5 to VCC +0.5 V
IIN DC Input Current, per Pin ±10 mA
PD Power Dissipation in Still Air, Plastic DIP+ 750 mW
SOIC Package+ 500
PD Power Dissipation per Output Transistor 100 mW
Tstg Storage Temperature -65 to +150 °C
TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C
(Plastic DIP or SOIC Package)
*
Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/°C from 65° to 125°C
SOIC Package: : - 7 mW/°C from 65° to 125°C

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Min Max Unit
VCC DC Supply Voltage (Referenced to GND) 3.0 18 V
VIN, VOUT DC Input Voltage, Output Voltage (Referenced to GND) 0 VCC V
TA Operating Temperature, All Package Types -55 +125 °C
*
I Multiplexer Switch Input Current Capability - 25 mA
ROH Output Load Resistance 100 - Ω
*
In certain applications, the external load-resistor current may include both VCC and signal-line components.

This device contains protection circuitry to guard against damage due to high static voltages or electric
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range
GND≤(VIN or VOUT)≤VCC.
Unused digital pins must be tied to an appropriate logic voltage level (e.g., either GND or VCC).
Unused Analog I/O pins may be left open or terminated.

98
 IW4051B

DC ELECTRICAL CHARACTERISTICS Digital Section

VCC Guaranteed Limit
Symbol Parameter Test Conditions V ≥ -55 ≤ 25 ≤ 125 Unit
°C °C °C
VIH Minimum High-Level VIS=VCC thru 1kΩ 5 3.5 3.5 3.5 V
Input Voltage, VEE=GND 10 7 7 7
Channel-Select or IIS<2µA on all OFF Chanels 15 11 11 11
Enable Inputs RL=1kΩ to GND
VIL Maximum Low -Level VIS=VCC thru 1kΩ 5 1.5 1.5 1.5 V
Input Voltage, VEE=GND 10 3 3 3
Channel-Select or IIS<2µA on all OFF Chanels 15 4 4 4
Enable Inputs RL=1kΩ to GND
IIN Maximum Input VIN=VCC or GND 18 ±0.1 ±0.1 ±1.0 µA
Leakage Current,
Channel-Select or
Enable Inputs
ICC Maximum Quiescent Channel Select = VCC or GND 5 5 5 150 µA
Supply Current (per 10 10 10 300
Package) 15 20 20 600
20 100 100 3000

DC ELECTRICAL CHARACTERISTICS Analog Section

VCC Guaranteed Limit
Symbol Parameter Test Conditions V ≥ -55 ≤ 25 ≤ 125 Unit
°C °C °C
RON Maximum “ON” Resistance VEE=GND=0 5 800 1050 1300 Ω
VIS = GND to VCC 10 310 400 550
15 200 240 320
∆RON Maximum Difference in VEE=GND=0 5 - 10 - Ω
“ON” Resistance Between 10 - 15 -
Any Two Channels in the 15 - 5 -
Same Package
IOFF Maximum Off- Channel VEE=GND=0 18 ±100 ±100 ±1000 nA
Leakage Current, Any One
Channel
Maximum Off- Channel VEE=GND=0 18 ±100 ±100 ±1000
Leakage Current, Common
Channel

99
IW4051B

AC ELECTRICAL CHARACTERISTICS(CL=50pF,Input tr=tf=20.0 ns)

VCC Guaranteed Limit
Symbol Parameter V ≥ -55 ≤ 25 ≤ 125 Unit
°C °C °C
tPLH, tPHL Maximum Propagation Delay , Analog Input to 5 60 60 120 ns
Analog Output (Figure 1) 10 30 30 60
RL=200kΩ 15 20 20 40
tPLZ, tPHZ Maximum Propagation Delay , Address to Analog 5 720 720 1440 ns
Output (Figure 2) RL=10kΩ 10 320 320 640
VEE=GND=0 15 240 240 480
VEE=-5V 5 450 450 900
tPLZ, Maximum Propagation Delay, Enable to Analog 5 720 720 1440 ns
tPZL Output (Figure 2) RL=10kΩ 10 320 320 640
VEE=GND=0 15 240 240 480
VEE=-10V 5 400 400 800
tPHZ, Maximum Propagation Delay, Enable to Analog 5 450 450 900 ns
tPZH Output (Figure 2) RL=10kΩ 10 210 210 420
VEE=GND=0 15 160 160 320
VEE=-10V 5 300 300 600
CIN Maximum Input Capacitance, Channel-Select or - 7.5 7.5 7.5 pF
Enable Inputs
CI/O Maximum Capacitance
VEE=GND=-5V
CIS 5 - 5 - pF

COS 5 - 30 -
Feedthrough CIOS 5 - 0.2 -

100
 IW4051B

ADDITIONAL APPLICATION CHARACTERISTICS

VCC VIS Limit*
Symbol Parameter Test Conditions V V 25 °C Unit
Maximum On- VEE=GND
Channel RL=1kΩ
Bandwidth or 20 log(VOS/VIS)=-3db
Minimum 10 5* 20 MHz
BW Frequency VOS at Common OUT/IN
Response (-3db)
VOS at Any Channel 10 5* 60
(-40db) VEE=GND
Feedthrough RL=1kΩ
Frequency (All 20 log(VOS/VIS)=-40db
Channels OFF) VOS at Common OUT/IN 10 5* 12

VOS at Any Channel 10 5* 8

(-40db) VEE=GND
Signal Crosstalk RL=1kΩ
Frequency 20 log(VOS/VIS)=-40db
Between Any 2 Channels 10 5* 3
THD Total Harmonic VEE=GND 5 2* 0.3 %
Distortion fIS=1kHz sine wave 10 3* 0.2
15 5* 012
- Address-or VEE=GND, RL=10kΩ** 10 - 65 mv
Enable to Signal tr,tf=20ns (Peak)
Crosstalk Square Wave
* Peak-to-peak voltage symmetrical about (VCC-VEE)/2.
** Both ends of channel.

101
IW4051B

Figure 1. Switching Waveforms

Figure 2. Switching Waveforms

EXPANDED LOGIC DIAGRAM

102