Scribd Logo
Upload

Welcome to Scribd!

  • 18 views

    EE 16405 Assignment I

    Uploaded by

    sandy
    1. Draw the differential equations, torque-voltage circuit, and torque-current circuit for the mechanical rotational system shown in Figure 1. Obtain the transfer function. 2. Use block diagram reduction to find the transfer function C/R for the system shown in Figure 2 and verify it using signal flow graph methods. 3. Find the transfer function for the system shown in Figure 3.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    EE 16405 Assignment I

    Uploaded by

    sandy
    18 views2 pages
    1. Draw the differential equations, torque-voltage circuit, and torque-current circuit for the mechanical rotational system shown in Figure 1. Obtain the transfer function. 2. Use block diagram reduction to find the transfer function C/R for the system shown in Figure 2 and verify it using signal flow graph methods. 3. Find the transfer function for the system shown in Figure 3.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. Draw the differential equations, torque-voltage circuit, and torque-current circuit for the mechanical rotational system shown in Figure 1. Obtain the transfer function. 2. Use block diagram reduction to find the transfer function C/R for the system shown in Figure 2 and verify it using signal flow graph methods. 3. Find the transfer function for the system shown in Figure 3.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    18 views2 pages

    EE 16405 Assignment I

    Uploaded by

    sandy
    1. Draw the differential equations, torque-voltage circuit, and torque-current circuit for the mechanical rotational system shown in Figure 1. Obtain the transfer function. 2. Use block diagram reduction to find the transfer function C/R for the system shown in Figure 2 and verify it using signal flow graph methods. 3. Find the transfer function for the system shown in Figure 3.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    ASSIGNMENT I

    1. Write the differential equations governing the Mechanical rotational system shown in fig.
    Draw the Torque-voltage and Torque-current electrical analogous circuits and verify. Obtain the
    transfer function.

    Figure 1

    2. Using block diagram reduction technique finds the transfer function C/R for the system
    shown in Figure.2 and verify it by using signal flow graph Method.

    Figure 2

    3. Find the transfer function of following system.

    Figure 3
    4. Consider the servo system shown in Figure .The motor shown is a servomotor, a dc motor
    designed specifically to be used in a control system.The operation of this system is as follows: A
    pair of potentiometer acts as an error-measuring device.They convert the input and output
    positions into proportional electric signals.The command input signal determines the angular
    position r of the wiper arm of the input potentiometer.
    The angular position r is the reference input to the system, and the electric potential of the arm
    is proportional to the angular position of the arm.The output shaft position determines the
    angular position c of the wiper arm of the output potentiometer.The difference between the
    input angular position r and the output angular position c is the error signal e, or The potential
    difference er - ec. = ev , is the error voltage, where e r is proportional to r and ec is proportional to
    c; that is, er = K0r and ec = K0c, where K0 is a proportionality constant.
    The error voltage that appears at the potentiometer terminals is amplified by the amplifier
    whose gain constant is K1 .The output voltage of this amplifier is applied to the armature circuit
    of the dc motor.A fixed voltage is applied to the field winding. If an error exists, the motor
    develops a torque to rotate the output load in such a way as to reduce the error to zero. For
    constant field current, the torque developed by the motor is T = K 2ia, where K2 is the motor
    torque constant and ia is the armature current.
    When the armature is rotating, a voltage proportional to the product of the flux and angular
    velocity is induced in the armature. For a constant flux, the induced voltage e b is directly
    proportional to the angular velocity dƟ/dt or e b=K3dƟ/dt where eb is the back emf, K3 is the
    back emf constant of the motor, and 0 is the angular displacement of the motor shaft.

    Obtain the transfer function between the motor shaft angular displacement Ɵ and the error
    voltage ev. Obtain also a block diagram for this system and a simplified block diagram when La is
    negligible.

    Figure 4

    You might also like