B460M Pro4 Manual

Version 1.
1
Published May 2020
Copyright©2020 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not
be registered trademarks or copyrights of their respective companies, and are used
only for identification or explanation and to the owners’ benefit, without intent to
infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished for
informational use only and subject to change without notice, and should not be
constructed as a commitment by ASRock. ASRock assumes no responsibility for
any errors or omissions that may appear in this documentation.
With respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or conditions of merchantability or fitness for a particular
purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY

The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance
controlled in Perchlorate Best Management Practices (BMP) regulations passed by the
California Legislature. When you discard the Lithium battery in California, USA, please
follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see www.dtsc.ca.gov/hazardouswaste/
perchlorate”
ASRock Website: http://www.asrock.com

AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage caused by our goods. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
Contents
Chapter 1 Introduction 1
1.1 Package Contents 1
1.2 Specifications 2
1.3 Motherboard Layout 7
1.4 I/O Panel 9
Chapter 2 Installation 10
2.1 Installing the CPU 11
2.2 Installing the CPU Fan and Heatsink 14
2.3 Installing Memory Modules (DIMM) 15
2.4 Expansion Slots (PCI Express Slots) 17
2.5 Jumpers Setup 18
2.6 Onboard Headers and Connectors 19
2.7 CrossFireX TM and Quad CrossFireX TM Operation Guide 24
2.7.1 Installing Two CrossFireX TM-Ready Graphics Cards 24
2.7.2 Driver Installation and Setup 26
2.8 M.2 WiFi/BT Module Installation Guide 27
2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1) 29
2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2) 32
Chapter 3 Software and Utilities Operation 36

3.1 Installing Drivers 36
3.2 ASRock Motherboard Utility (A-Tuning) 37
3.3 ASRock Live Update & APP Shop 40

3.3.1 UI Overview 40
3.3.2 Apps 41
3.3.3 BIOS & Drivers 44
3.3.4 Setting 45
3.4 Nahimic Audio 46
3.5 ASRock Polychrome SYNC 47
Chapter 4 UEFI SETUP UTILITY 50

4.1 Introduction 50
4.2 EZ Mode 51
4.3 Advanced Mode 52
4.3.1 UEFI Menu Bar 52
4.3.2 Navigation Keys 53
4.4 Main Screen 54
4.5 OC Tweaker Screen 55
4.6 Advanced Screen 65
4.6.1 CPU Configuration 66
4.6.2 Chipset Configuration 68
4.6.3 Storage Configuration 71
4.6.4 Intel(R) Thunderbolt 72
4.6.5 Super IO Configuration 73
4.6.6 ACPI Configuration 74
4.6.7 USB Configuration 75
4.6.8 Trusted Computing 76
4.7 Tools 77
4.8 Hardware Health Event Monitoring Screen 79
4.9 Security Screen 82
4.10 Boot Screen 83
4.11 Exit Screen 86

B460M Pro4
Chapter 1 Introduction
Thank you for purchasing ASRock B460M Pro4 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control.
It delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
In this documentation, Chapter 1 and 2 contains the introduction of the

motherboard and step-by-step installation guides. Chapter 3 contains the operation
guide of the software and utilities. Chapter 4 contains the configuration guide of
the BIOS setup.
Because the motherboard specifications and the BIOS software might be updated, the
content of this documentation will be subject to change without notice. In case any
modifications of this documentation occur, the updated version will be available on
ASRock’s website without further notice. If you require technical support related to
this motherboard, please visit our website for specific information about the model
you are using. You may find the latest VGA cards and CPU support list on ASRock’s
website as well. ASRock website http://www.asrock.com.
1.1 Package Contents

• ASRock B460M Pro4 Motherboard (Micro ATX Form Factor)
• ASRock B460M Pro4 Quick Installation Guide
• ASRock B460M Pro4 Support CD
• 2 x Serial ATA (SATA) Data Cables (Optional)
• 3 x Screws for M.2 Sockets (Optional)
• 1 x Standoff for M.2 Socket (Optional)
• 1 x I/O Panel Shield English
1
1.2 Specifications
Platform • Micro ATX Form Factor

• Solid Capacitor design
CPU • Supports 10th Gen Intel® CoreTM Processors (Socket 1200)

• Digi Power design
• 9 Power Phase design
• Supports Intel® Turbo Boost Max 3.0 Technology
Chipset • Intel® B460
Memory • Dual Channel DDR4 Memory Technology

• 4 x DDR4 DIMM Slots
• Supports DDR4 2933/2800/2666/2400/2133 non-ECC, un-
buffered memory
* Please refer to Memory Support List on ASRock's website for
more information. (http://www.asrock.com/)
* CoreTM (i9/i7) support DDR4 up to 2933; CoreTM (i5/i3),
Pentium® and Celeron® support DDR4 up to 2666.
• Supports ECC UDIMM memory modules (operate in non-
ECC mode)
• Max. capacity of system memory: 128GB
• Supports Intel® Extreme Memory Profile (XMP) 2.0
• 15μ Gold Contact in DIMM Slots
Expansion • 2 x PCI Express 3.0 x16 Slots (PCIE1/PCIE3: single at x16

Slot (PCIE1); dual at x16 (PCIE1) / x4 (PCIE3))
* Supports NVMe SSD as boot disks
• 1 x PCI Express 3.0 x1 Slot
• Supports AMD Quad CrossFireXTM and CrossFireXTM
• 1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module
English
2
B460M Pro4
Graphics * Intel® UHD Graphics Built-in Visuals and the VGA outputs
can be supported only with processors which are GPU
integrated.
• Hardware Accelerated Codecs: AVC/H.264, HEVC/H.265
8bit, HEVC/H.265 10bit, VP8, VP9 8bit, VP9 10bit, MPEG 2,
MJPEG, VC-1
* VP9 10bit and VC-1 are for decode only.
* VP8 and VP9 encode are not supported by Windows OS.
• Graphics, Media & Compute: Microsoft DirectX 12, OpenGL
4.5, Intel® Built In Visuals, Intel® Quick Sync Video, Hybrid /
Switchable Graphics, OpenCL 2.1
• Display & Content Security: Rec. 2020 (Wide Color Gamut),
Microsoft PlayReady 3.0, Intel® SGX Content Protection,
UHD/HDR Blu-ray Disc
• Three graphics output options: D-Sub, HDMI and
DisplayPort 1.4
• Supports Triple Monitor
• Supports HDMI 1.4 with max. resolution up to 4K x 2K
(4096x2160) @ 30Hz
• Supports DisplayPort 1.4 with max. resolution up to 4K x 2K
(4096x2304) @ 60Hz
• Supports D-Sub with max. resolution up to 1920x1200 @
60Hz
• Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and
HBR (High Bit Rate Audio) with HDMI 1.4 Port
(Compliant HDMI monitor is required)
• Supports HDCP 2.3 with HDMI 1.4 and DisplayPort 1.4
Ports
• Supports 4K Ultra HD (UHD) playback with HDMI 1.4 and
DisplayPort 1.4 Ports
Audio • 7.1 CH HD Audio with Content Protection (Realtek

ALC1200 Audio Codec)
• Premium Blu-ray Audio support
• Supports Surge Protection
• PCB Isolate Shielding
English
• Individual PCB Layers for R/L Audio Channel

• Nahimic Audio
3
LAN • Gigabit LAN 10/100/1000 Mb/s
• Giga PHY Intel® I219V
• Supports Wake-On-LAN
• Supports Lightning/ESD Protection
• Supports Energy Efficient Ethernet 802.3az
• Supports PXE
Rear Panel • 1 x Antenna Bracket

I/O • 1 x PS/2 Mouse/Keyboard Port
• 1 x D-Sub Port
• 1 x HDMI Port
• 1 x DisplayPort 1.4
• 4 x USB 3.2 Gen1 Type-A Ports (Supports ESD Protection)
• 1 x USB 3.2 Gen1 Type-C Port (Supports ESD Protection)
• 2 x USB 2.0 Ports (Supports ESD Protection)
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED
LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
Storage • 6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology
17), NCQ, AHCI and Hot Plug*
* If M2_2 is occupied by a SATA-type M.2 device, SATA3_0 will
be disabled.
• 1 x Ultra M.2 Socket (M2_1), supports M Key type
2242/2260/2280 M.2 PCI Express module up to Gen3 x4 (32
Gb/s)**
• 1 x Ultra M.2 Socket (M2_2), supports M Key type
2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Ex-
press module up to Gen3 x4 (32 Gb/s)**
** Supports Intel® OptaneTM Technology (M2_1)
** Supports NVMe SSD as boot disks
** Supports ASRock U.2 Kit
English
4
B460M Pro4
Connector • 1 x SPI TPM Header

• 1 x Chassis Intrusion and Speaker Header
• 2 x RGB LED Headers
* Support in total up to 12V/3A, 36W LED Strip
• 2 x Addressable LED Headers
* Support in total up to 5V/3A, 15W LED Strip
• 1 x CPU Fan Connector (4-pin)
* The CPU Fan Connector supports the CPU fan of maximum
1A (12W) fan power.
• 1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan
Speed Control)
* The CPU/Water Pump Fan supports the water cooler fan of
maximum 2A (24W) fan power.
• 3 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan
Speed Control)
• * The Chassis/Water Pump Fan supports the water cooler fan
of maximum 2A (24W) fan power.
• * CPU_FAN2/WP, CHA_FAN1/WP, CHA_FAN2/WP and
CHA_FAN3/WP can auto detect if 3-pin or 4-pin fan is in
use.
• 1 x 24 pin ATX Power Connector
• 1 x 8 pin 12V Power Connector
• 1 x Front Panel Audio Connector
• 1 x Thunderbolt AIC Connector (5-pin) (Supports ASRock
Thunderbolt 3 AIC R2.0 Card only)
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports
ESD Protection)
• 1 x USB 3.2 Gen1 Header (Supports 2 USB 3.2 Gen1 ports)
(Supports ESD Protection)
BIOS • AMI UEFI Legal BIOS with multilingual GUI support

Feature • ACPI 6.0 Compliant wake up events
• SMBIOS 2.7 Support
• CPU Core/Cache, GT, DRAM, VPPM, PCH 1.05V, VCCST,
VCCSA Voltage Multi-adjustment
English
5
Hardware • Temperature Sensing: CPU, CPU/Water Pump, Chassis/Wa-
Monitor ter Pump Fans
• Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water
Pump Fans
• Quiet Fan (Auto adjust chassis fan speed by CPU tempera-
ture): CPU, CPU/Water Pump, Chassis/Water Pump Fans
• Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/
Water Pump Fans
• CASE OPEN detection
• Voltage monitoring: +12V, +5V, +3.3V, CPU Vcore, DRAM,
VPPM, PCH, VCCSA, VCCST
OS • Microsoft® Windows® 10 64-bit
Certifica- • FCC, CE
tions • ErP/EuP Ready (ErP/EuP ready power supply is required)
* For detailed product information, please visit our website: http://www.asrock.com
Please realize that there is a certain risk involved with overclocking, including
adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using
third-party overclocking tools. Overclocking may affect your system’s stability, or
even cause damage to the components and devices of your system. It should be done
at your own risk and expense. We are not responsible for possible damage caused by
overclocking.
English
6
B460M Pro4
1.3 Motherboard Layout
1 2 3 4 5
Keyboard
B: USB2
T: USB1
USB2.0
/Mouse
RGB_LED1
PS2
6
ATX12V1
CPU_FAN1 1
ADDR_LED1
CPU_FAN2/WP 7
HDMI1
1
VGA1
Display1
DDR4_A1 (64 bit, 288-pin module)
DDR4_B1 (64 bit, 288-pin module)
DDR4_B2 (64 bit, 288-pin module)

DDR4_A2 (64 bit, 288-pin module)
ATXPWR1
USB31_TC_1
USB 3.2 Gen1
8
USB 3.2 Gen1
T: USB3_2
B: USB3_1
USB 3.2 Gen1

T: USB3_4
Top:
B: USB3_3 RJ-45
28
USB3_5_6
M2_1
9
LINE IN
Top:
MIC IN
Bottom:
FRONT
Center:
CHA_FAN1/WP
1
10
PCIE1
SATA3_2
SATA3_3
11
12
CMOS
Intel
M2_2
Battery SATA3_4
SATA3_5
RoHS B460 13
PCIE2
M2_3
CHA_FAN3/WP
14
PCIE3 SATA3_1 SPK_CI1
1
ADDR_LED2
1
15
PANEL1
CHA_FAN2/WP USB3_4 USB5_6 SPI_TPM_J1 PLED PWRBTN
T B1
HD_AUDIO1 RGB_LED2 CLRMOS1
1
1
1 1
1 1 1
16
SATA3_0 HDLED RESET
27 26 25 24 23 22 21 20 19 18 17
English
7
No. Description
1 ATX 12V Power Connector (ATX12V1)
2 CPU/Water Pump Fan Connector (CPU_FAN2/WP)
3 CPU Fan Connector (CPU_FAN1)
4 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1)
5 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2)
6 RGB LED Header (RGB_LED1)
7 Addressable LED Header (ADDR_LED1)
8 ATX Power Connector (ATXPWR1)
9 USB 3.2 Gen1 Header (USB3_5_6)
10 SATA3 Connector (SATA3_2)
14 Chassis/Water Pump Fan Connector (CHA_FAN3/WP)
15 Chassis Intrusion and Speaker Header (SPK_CI1)
16 System Panel Header (PANEL1)
19 SPI TPM Header (SPI_TPM_J1)
20 USB 2.0 Header (USB5_6)
21 USB 2.0 Header (USB3_4)
22 Clear CMOS Jumper (CLRMOS1)
24 Thunderbolt AIC Connector (TB1)
25 RGB LED Header (RGB_LED2)
26 Addressable LED Header (ADDR_LED2)
27 Front Panel Audio Header (HD_AUDIO1)
English
8
B460M Pro4
1.4 I/O Panel

4
1 2 3 5
13 12 11 10 9 8 7 6
No. Description No. Description

1 USB 2.0 Ports (USB12) 8 USB 3.2 Gen1 Ports (USB3_1_2)
2 D-Sub Port 9 USB 3.2 Gen1 Type-C Port (USB3_TC_1)
3 LAN RJ-45 Port* 10 Antenna Bracket
4 Line In (Light Blue)** 11 DisplayPort 1.4
5 Front Speaker (Lime)** 12 HDMI Port
6 Microphone (Pink)** 13 PS/2 Mouse/Keyboard Port
7 USB 3.2 Gen1 Ports (USB3_3_4)
* There are two LEDs on the LAN port. Please refer to the table below for the LAN port LED indications.
ACT/LINK LED
SPEED LED
LAN Port
Activity / Link LED Speed LED

Status Description Status Description
Off No Link Off 10Mbps connection
Blinking Data Activity Orange 100Mbps connection
On Link Green 1Gbps connection
** Function of the Audio Ports in 7.1-channel Configuration:

English
Port Function
Light Blue (Rear panel) Rear Speaker Out
Lime (Rear panel) Front Speaker Out
Pink (Rear panel) Central /Subwoofer Speaker Out
Lime (Front panel) Side Speaker Out
9
Chapter 2 Installation
This is a Micro ATX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
• Make sure to unplug the power cord before installing or removing the motherboard
components. Failure to do so may cause physical injuries and damages to motherboard
components.
• In order to avoid damage from static electricity to the motherboard’s components,
NEVER place your motherboard directly on a carpet. Also remember to use a grounded
wrist strap or touch a safety grounded object before you handle the components.
• Hold components by the edges and do not touch the ICs.
• Whenever you uninstall any components, place them on a grounded anti-static pad or
in the bag that comes with the components.
• When placing screws to secure the motherboard to the chassis, please do not over-
tighten the screws! Doing so may damage the motherboard.
English
10
B460M Pro4
2.1 Installing the CPU
1. Before you insert the 1200-Pin CPU into the socket, please check if the PnP cap is on the
socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not
force to insert the CPU into the socket if above situation is found. Otherwise, the CPU
will be seriously damaged.
2. Unplug all power cables before installing the CPU.
English
11
4
5
3
12
English
B460M Pro4
Please save and replace the cover if the processor is removed. The cover must be placed if
you wish to return the motherboard for after service.
English
13
2.2 Installing the CPU Fan and Heatsink
1 2
AN
_F
U
CP
English
14
B460M Pro4
2.3 Installing Memory Modules (DIMM)
This motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots,
and supports Dual Channel Memory Technology.
1. For dual channel configuration, you always need to install identical (the same
brand, speed, size and chip-type) DDR4 DIMM pairs.
2. It is unable to activate Dual Channel Memory Technology with only one or three
memory module installed.
3. It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4
slot; otherwise, this motherboard and DIMM may be damaged.
Dual Channel Memory Configuration
Priority DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2

1 Populated Populated
2 Populated Populated Populated Populated
The DIMM only fits in one correct orientation. It will cause permanent damage to
the motherboard and the DIMM if you force the DIMM into the slot at incorrect
orientation.
English
15
3
2
1
16
English
B460M Pro4
2.4 Expansion Slots (PCI Express Slots)

There are 3 PCI Express slots on the motherboard.
Before installing an expansion card, please make sure that the power supply is
switched off or the power cord is unplugged. Please read the documentation of the
expansion card and make necessary hardware settings for the card before you start
the installation.
PCIe slots:
PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics cards.
PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics cards.
PCIe Slot Configurations

PCIE1 PCIE3
Single Graphics Card x16 N/A
Two Graphics Cards in

x16 x4
CrossFireXTM Mode
For a better thermal environment, please connect a chassis fan to the motherboard’s
chassis fan connector (CHA_FAN1/WP, CHA_FAN2/WP or CHA_FAN3/WP) when
using multiple graphics cards.
English
17
2.5 Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on
the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is
“Open”.
Clear CMOS Jumper

(CLRMOS1)
2-pin Jumper
(see p.7, No. 22)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system
parameters to default setup, please turn off the computer and unplug the power
cord from the power supply. After waiting for 15 seconds, use a jumper cap to
short the pins on CLRMOS1 for 5 seconds. However, please do not clear the
CMOS right after you update the BIOS. If you need to clear the CMOS when you
just finish updating the BIOS, you must boot up the system first, and then shut it
down before you do the clear-CMOS action. Please be noted that the password,
date, time, and user default profile will be cleared only if the CMOS battery is
removed. Please remember toremove the jumper cap after clearing the CMOS.
If you clear the CMOS, the case open may be detected. Please adjust the BIOS option
“Clear Status” to clear the record of previous chassis intrusion status.
English
18
B460M Pro4
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over
these headers and connectors. Placing jumper caps over the headers and connectors
will cause permanent damage to the motherboard.
System Panel Header PLED+ Connect the power

PLED-
(9-pin PANEL1) PWRBTN#
GND
switch, reset switch and
(see p.7, No. 16) system status indicator on
1
GND
the chassis to this header
RESET#
GND according to the pin
HDLED-
HDLED+ assignments below. Note
the positive and negative
pins before connecting
the cables.
PWRBTN (Power Switch):

Connect to the power switch on the chassis front panel. You may configure the way to
turn off your system using the power switch.
RESET (Reset Switch):

Connect to the reset switch on the chassis front panel. Press the reset switch to restart
the computer if the computer freezes and fails to perform a normal restart.
PLED (System Power LED):

Connect to the power status indicator on the chassis front panel. The LED is on when
the system is operating. The LED keeps blinking when the system is in S1/S3 sleep
state. The LED is off when the system is in S4 sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):

Connect to the hard drive activity LED on the chassis front panel. The LED is on
when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly consists
of power switch, reset switch, power LED, hard drive activity LED, speaker and etc.
When connecting your chassis front panel module to this header, make sure the wire
assignments and the pin assignments are matched correctly.
SPEAKER
Chassis Intrusion and Please connect the
DUMMY
Speaker Header DUMMY chassis intrusion and the
English
+5V
(7-pin SPK_CI1) chassis speaker to this
(see p.7, No. 15) 1 header.
SIGNAL
GND
DUMMY
19
Serial ATA3 Connectors These six SATA3
SATA3_4 SATA3_2
SATA3_5 SATA3_3
(SATA3_0: connectors support SATA
see p.7, No. 17) data cables for internal
(SATA3_1: storage devices with up to
see p.7, No. 18) 6.0 Gb/s data transfer rate.
(SATA3_2: If M2_2 is occupied by a
see p.7, No. 10) SATA3_1 SATA-type M.2 device,
(SATA3_3: SATA3_0 will be disabled.
see p.7, No. 11)
(SATA3_4:
SATA3_0
see p.7, No. 12)
(SATA3_5:
see p.7, No. 13)
USB 2.0 Headers USB_PWR There are two USB

P-
(9-pin USB3_4) P+
GND 2.0 headers on this
DUMMY
(see p.7, No. 21) motherboard.Each USB
(9-pin USB5_6) 1 2.0 header can support
GND
(see p.7, No. 20) P-
P+ two ports.
USB_PWR
USB 3.2 Gen1 Header There is one USB 3.2

Vbus
Vbus IntA_PB_SSRX-
(19-pin USB3_5_6) Gen1 header on this

IntA_PA_SSRX- IntA_PB_SSRX+
IntA_PA_SSRX+ GND
(see p.7, No. 9) motherboard. Each USB

GND IntA_PB_SSTX-
IntA_PA_SSTX- IntA_PB_SSTX+
3.2 Gen1 header can

IntA_PA_SSTX+ GND
GND IntA_PB_D-
support two ports.

IntA_PA_D- IntA_PB_D+
IntA_PA_D+ Dummy
1
Front Panel Audio Header This header is for

GND
PRESENCE#
MIC_RET
(9-pin HD_AUDIO1) OUT_RET connecting audio devices
(see p.7, No. 27) to the front audio panel.
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
English
20
B460M Pro4
1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis
must support HDA to function correctly. Please follow the instructions in our
manual and chassis manual to install your system.
2. If you use an AC’97 audio panel, please install it to the front panel audio header by
the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to
connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel
and adjust “Recording Volume”.
Chassis/Water Pump Fan 1

2
GND
FAN_VOLTAGE
This motherboard
Connectors 3
4
CHA_FAN_SPEED
FAN_SPEED_CONTROL
provides three 4-Pin water
(4-pin CHA_FAN1/WP) cooling chassis fan
(see p.7, No. 28) connectors. If you plan to
connect a 3-Pin chassis
(4-pin CHA_FAN2/WP) 4 3 2 1
water cooler fan, please
(see p.7, No. 23) GND
connect it to Pin 1-3.
(4-pin CHA_FAN3/WP)
FAN_VOLTAGE_CONTROL
FAN_SPEED
FAN_SPEED_CONTROL
(see p.7, No. 14)
CPU Fan Connector FAN_VOLTAGE_CONTROL

FAN_SPEED
This motherboard pro-
FAN_SPEED_CONTROL
(4-pin CPU_FAN1) vides a 4-Pin CPU fan
GND
(see p.7, No. 3) (Quiet Fan) connector.

If you plan to connect a
3-Pin CPU fan, please
CPU/Water Pump Fan FAN_VOLTAGE_CONTROL

FAN_SPEED
This motherboard
FAN_SPEED_CONTROL
Connector provides a 4-Pin water
GND
(4-pin CPU_FAN2/WP) cooling CPU fan

(see p.7, No. 2) connector. If you plan
to connect a 3-Pin CPU
water cooler fan, please
English
21
ATX Power Connector 12 24 This motherboard pro-
(24-pin ATXPWR1) vides a 24-pin ATX power
(see p.7, No. 8) connector. To use a 20-pin
ATX power supply, please
plug it along Pin 1 and Pin
1 13 13.
ATX 12V Power 8 5 This motherboard pro-

Connector vides a 8-pin ATX 12V
(8-pin ATX12V1) 4 1
power connector. To use a
(see p.7, No. 1) 4-pin ATX power supply,
please plug it along Pin 1
and Pin 5.
SPI TPM Header SPI_DQ3

This connector supports SPI
+3.3V
(13-pin SPI_TPM_J1) TPM_Present Trusted Platform Module (TPM)
CLK
SPI_MOSI
(see p.7, No. 19) RST#
system, which can securely
TPM_PIRQ store keys, digital certificates,
passwords, and data. A TPM
1
system also helps enhance
SPI_TPM_CS#
GND network security, protects digital
RSMRST#
SPI_MISO identities, and ensures platform
SPI_CS0
SPI_DQ2 integrity.
Thunderbolt AIC 1 Please connect a Thunderbolt™

Connector add-in card (AIC) to this
(5-pin TB1) connector via the GPIO cable.
(see p.7, No. 24) *Please install the Thunderbolt™
AIC card to PCIE3 (default slot).
English
22
B460M Pro4
RGB LED Headers B RGB LED headers are used to

(4-pin RGB_LED1) R connect RGB LED extension
(see p.7, No. 6) G cables which allow users to
12V choose from various LED light-
1
ing effects.
(4-pin RGB_LED2) Caution: Never install the RGB
(see p.7, No. 25) 1 LED cable in the wrong orienta-
12V G R B
tion; otherwise, the cable may
be damaged.
*Please refer to page 47 for for
further instructions on this
header.
Addressable LED Header The headers are used to connect

(3-pin ADDR_LED1) Addressable LED extension ca-
(see p.7, No. 7) bles which allow users to choose
from various LED lighting
effects.
(3-pin ADDR_LED2) 1
Caution: Never install the
(see p.7, No. 26) GND
Addressable LED cable in the
DO_ADDR wrong orientation; otherwise,
VOUT
the cable may be damaged.
*Please refer to page 48 for
further instructions on this
header.
English
23
2.7 CrossFireXTM and Quad CrossFireXTM Operation Guide
This motherboard supports CrossFireXTM and Quad CrossFireXTM that allows you
to install up to three identical PCI Express x16 graphics cards.
1. You should only use identical CrossFireXTM-ready graphics cards that are AMD
certified.
2. Make sure that your graphics card driver supports AMD CrossFireXTM technology.
Download the drivers from the AMD’s website: www.amd.com
3. Make sure that your power supply unit (PSU) can provide at least the minimum
power your system requires. It is recommended to use a AMD certified PSU. Please
refer to the AMD’s website for details.
4. If you pair a 12-pipe CrossFireXTM Edition card with a 16-pipe card, both cards will
operate as 12-pipe cards while in CrossFireXTM mode.
5. Different CrossFireXTM cards may require different methods to enable CrossFi-
reXTM. Please refer to AMD graphics card manuals for detailed installation guide.
2.7.1 Installing Two CrossFireXTM-Ready Graphics Cards
Step 1
Insert one graphics card into PCIE1 slot
and the other graphics card to PCIE3 slot.
Make sure that the cards are properly
seated on the slots.
Step 2
Connect two graphics cards by installing
a CrossFire Bridge on the CrossFire Bridge
CrossFire Bridge Interconnects on the top of the graphics
cards. (The CrossFire Bridge is provided
with the graphics card you purchase, not
bundled with this motherboard. Please
refer to your graphics card vendor for
details.)
English
24
B460M Pro4
Step 3
Connect a VGA cable or a DVI cable to the
monitor connector or the DVI connec-
tor of the graphics card that is inserted to
PCIE1 slot.
English
25
2.7.2 Driver Installation and Setup
Step 1
Power on your computer and boot into OS.
Step 2
Remove the AMD drivers if you have any VGA drivers installed in your system.
The Catalyst Uninstaller is an optional download. We recommend using this utility

to uninstall any previously installed Catalyst drivers prior to installation. Please
check AMD’s website for AMD driver updates.
Step 3
Install the required drivers and CATALYST Control Center then restart your
computer. Please check AMD’s website for details.
Step 4
Double-click the AMD Catalyst Control
AMD Catalyst Control Center Center icon in the Windows® system tray.
Step 5
In the left pane, click Performance and
then AMD CrossFireXTM . Then select
Enable AMD CrossFireX and click Apply.
Select the GPU number according to your
graphics card and click Apply.
English
26
B460M Pro4
2.8 M.2 WiFi/BT Module Installation Guide

The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and
versatile card edge connector that aims to replace mPCIe and mSATA. The M.2 Socket
(Key E) supports type 2230 WiFi/BT module.
* The M.2 socket does not support SATA M.2 SSDs.
Installing the WiFi/BT module
Step 1
Prepare a type 2230 WiFi/BT module

and the screw.
Step 2
Find the nut location to be used.
PCB Length: 3cm

Module Type: Type2230
A
English
27
Step 3
Gently insert the WiFi/BT module

into the M.2 slot. Please be aware
that the module only fits in one
orientation.
A 20o
Step 4
Tighten the screw with a screwdriver

to secure the module into place.
Please do not overtighten the screw as
this might damage the module.
A
English
28
B460M Pro4
2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1)

versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2
Socket (M2_1) supports M Key type 2242/2260/2280 M.2 PCI Express module up to Gen3
x4 (32 Gb/s).
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module

and the screw.
1
2 Step 2
Before installing a M.2 (NGFF)

1
SSD module, please loosen
the screws to remove the M.2
heatsink.
*Please remove the protective
films on the bottom side of the
M.2 heatsink before you install
a M.2 SSD module.
3
Step 3
2
1
Depending on the PCB type and
length of your M.2_SSD (NGFF)
module, find the corresponding nut
location to be used.
C B A
No. 1 2 3
English
Nut Location A B C
PCB Length 4.2cm 6cm 8cm
Module Type Type2242 Type2260 Type 2280
29
Step 4
Move the standoff based on the

module type and length.
The standoff is placed at the nut
C B A location C by default. Skip Step 4
and 5 and go straight to Step 6 if you
are going to use the default nut.
Otherwise, release the standoff by
hand.
Step 5
Peel off the yellow protective film on

the nut to be used. Hand tighten the
C B A
standoff into the desired nut location
on the motherboard.
Step 6
Gently insert the M.2 (NGFF) SSD

module into the M.2 slot. Please
be aware that the M.2 (NGFF) SSD
module only fits in one orientation.
C B A
C B A 20o
Step 7

English
Please do not overtighten the screw

NUT2 NUT1
as this might damage the module.
30
B460M Pro4
M.2_SSD (NGFF) Module Support List
Vendor Interface P/N

ADATA PCIe3 x4 ASX7000NP-128GT-C
ADATA PCIe3 x4 ASX8000NP-256GM-C
Apacer PCIe3 x4 AP240GZ280
Corsair PCIe3 x4 CSSD-F240GBMP500
Intel PCIe3 x4 SSDPEKKF256G7
Kingston PCIe3 x4 SKC1000/480G
Kingston PCIe2 x4 SH2280S3/480G
OCZ PCIe3 x4 RVD400 -M2280-512G (NVME)
PATRIOT PCIe3 x4 PH240GPM280SSDR NVME
Plextor PCIe3 x4 PX-128M8PeG
Plextor PCIe3 x4 PX-1TM8PeG
Plextor PCIe PX-G256M6e
Samsung PCIe3 x4 SM961 MZVPW128HEGM (NVM)
Samsung PCIe3 x4 PM961 MZVLW128HEGR (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250) (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250BW) (NVME)
Samsung PCIe3 x4 SM951 (NVME)
Samsung PCIe3 x4 SM951 (MZHPV256HDGL)
Samsung PCIe x4 XP941-512G (MZHPU512HCGL)
SanDisk PCIe SD6PP4M-128G
TEAM PCIe3 x4 TM8FP2240G0C101
TEAM PCIe3 x4 TM8FP2480GC110
WD PCIe3 x4 WDS256G1X0C-00ENX0 (NVME)
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com
English
31
2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2)
versatile card edge connector that aims to replace mPCIe and mSATA. The Ultra M.2
Socket (M2_2) supports M Key type 2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI
Express module up to Gen3 x4 (32 Gb/s).
* If M2_2 is occupied by a SATA-type M.2 device, SATA3_0 will be disabled.
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module

and the screw.
2 Step 2
1
Depending on the PCB type and
length of your M.2_SSD (NGFF)
module, find the corresponding nut
location to be used.
B A
No. 1 2
Nut Location A B
PCB Length 6cm 8cm
Module Type Type2260 Type 2280
English
32
B460M Pro4
Step 3
Move the standoff based on the

module type and length.
The standoff is placed at the nut
B A
location B by default. Skip Step 3 and
4 and go straight to Step 5 if you are
going to use the default nut.
Otherwise, release the standoff by
hand.
Step 4
Peel off the yellow protective film on

the nut to be used. Hand tighten the
B A standoff into the desired nut location
on the motherboard.
Step 5
Gently insert the M.2 (NGFF) SSD

module into the M.2 slot. Please
be aware that the M.2 (NGFF) SSD
module only fits in one orientation.
B A
B A 20o
Step 6

English
Please do not overtighten the screw

NUT2 NUT1
as this might damage the module.
33
M.2_SSD (NGFF) Module Support List
Vendor Interface P/N

Team SATA3 TM4PS4128GMC105
Transcend SATA3 TS256GMTS400
ADATA SATA3 AXNS381E-128GM-B
ADATA SATA3 AXNS381E-256GM-B
ADATA SATA3 ASU800NS38-256GT-C
ADATA SATA3 ASU800NS38-512GT-C
Apacer PCIe3 x4 AP240GZ280
Corsair PCIe3 x4 CSSD-F240GBMP500
Crucial SATA3 CT120M500SSD4
Crucial SATA3 CT240M500SSD4
Intel SATA3 Intel SSDSCKGW080A401/80G
Kingston SATA3 SM2280S3
Kingston PCIe3 x4 SKC1000/480G
Kingston PCIe2 x4 SH2280S3/480G
OCZ PCIe3 x4 RVD400 -M2280-512G (NVME)
PATRIOT PCIe3 x4 PH240GPM280SSDR NVME
Plextor PCIe3 x4 PX-1TM8PeG
Samsung PCIe3 x4 SM961 MZVPW128HEGM (NVM)
Samsung PCIe3 x4 PM961 MZVLW128HEGR (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250) (NVME)
Samsung PCIe3 x4 960 EVO (MZ-V6E250BW) (NVME)
English
Samsung PCIe x4 XP941-512G (MZHPU512HCGL)

34
B460M Pro4

TEAM PCIe3 x4 TM8FP2240G0C101
TEAM PCIe3 x4 TM8FP2480GC110
V-Color SATA3 VLM100-120G-2280B-RD
V-Color SATA3 VLM100-240G-2280RGB
V-Color SATA3 VSM100-240G-2280
V-Color SATA3 VLM100-240G-2280B-RD
WD SATA3 WDS100T1B0B-00AS40
WD SATA3 WDS240G1G0B-00RC30
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for
details: http://www.asrock.com
English
35
Chapter 3 Software and Utilities Operation
3.1 Installing Drivers
The Support CD that comes with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard’s features.
Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu does not appear automatically, locate and double click on the file
“ASRSETUP.EXE” in the Support CD to display the menu.
Drivers Menu
The drivers compatible to your system will be auto-detected and listed on the
support CD driver page. Please click Install All or follow the order from top to
bottom to install those required drivers. Therefore, the drivers you install can work
properly.
Utilities Menu
The Utilities Menu shows the application software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
English
36
B460M Pro4
3.2 ASRock Motherboard Utility (A-Tuning)

ASRock Motherboard Utility (A-Tuning) is ASRock’s multi purpose software suite
with a new interface, more new features and improved utilities.
3.2.1 Installing ASRock Motherboard Utility (A-Tuning)

ASRock Motherboard Utility (A-Tuning) can be downloaded from ASRock Live
Update & APP Shop. After the installation, you will find the icon “ASRock Mother-
board Utility (A-Tuning)“ on your desktop. Double-click the “ASRock Motherboard
Utility (A-Tuning)“ icon, ASRock Motherboard Utility (A-Tuning) main menu
will pop up.
3.2.2 Using ASRock Motherboard Utility (A-Tuning)

There are four sections in ASRock Motherboard Utility (A-Tuning) main menu:
Operation Mode, System Info, FAN-Tastic Tuning and Settings.
Operation Mode
Choose an operation mode for your computer.
English
37
System Info
View information about the system.
*The System Browser tab may not appear for certain models.
FAN-Tastic Tuning
Configure up to five different fan speeds using the graph. The fans will automatically shift
to the next speed level when the assigned temperature is met.
English
38
B460M Pro4
Settings
Configure ASRock Motherboard Utility (A-Tuning). Click to select "Auto run
at Windows Startup" if you want ASRock Motherboard Utility (A-Tuning) to be
launched when you start up the Windows operating system.
English
39
3.3 ASRock Live Update & APP Shop
The ASRock Live Update & APP Shop is an online store for purchasing and
downloading software applications for your ASRock computer. You can quickly and
easily install various apps and support utilities. With ASRock Live Update & APP
Shop, you can optimize your system and keep your motherboard up to date simply
with a few clicks.
Double-click on your desktop to access ASRock Live Update & APP Shop
utility.
*You need to be connected to the Internet to download apps from the ASRock Live Update & APP Shop.
3.3.1 UI Overview
Category Panel Hot News
Information Panel
Category Panel: The category panel contains several category tabs or buttons that
when selected the information panel below displays the relative information.
Information Panel: The information panel in the center displays data about the
currently selected category and allows users to perform job-related tasks.
English
Hot News: The hot news section displays the various latest news. Click on the image
to visit the website of the selected news and know more.
40
B460M Pro4
3.3.2 Apps
When the "Apps" tab is selected, you will see all the available apps on screen for you
to download.
Installing an App
Step 1
Find the app you want to install.
The most recommended app appears on the left side of the screen. The other various
apps are shown on the right. Please scroll up and down to see more apps listed.
You can check the price of the app and whether you have already intalled it or not.
- The red icon displays the price or "Free" if the app is free of charge.
- The green "Installed" icon means the app is installed on your computer.
Step 2
Click on the app icon to see more details about the selected app.
English
41
Step 3
If you want to install the app, click on the red icon to start downloading.
Step 4
When installation completes, you can find the green "Installed" icon appears on the
upper right corner.
To uninstall it, simply click on the trash can icon .

English
*The trash icon may not appear for certain apps.
42
B460M Pro4
Upgrading an App
You can only upgrade the apps you have already installed. When there is an
available new version for your app, you will find the mark of "New Version"
appears below the installed app icon.
Step 1
Click on the app icon to see more details.
Step 2
Click on the yellow icon to start upgrading.
English
43
3.3.3 BIOS & Drivers
Installing BIOS or Drivers

When the "BIOS & Drivers" tab is selected, you will see a list of recommended or
critical updates for the BIOS or drivers. Please update them all soon.
Step 1
Please check the item information before update. Click on to see more details.
Step 2
Click to select one or more items you want to update.
Step 3
Click Update to start the update process.

English
44
B460M Pro4
3.3.4 Setting
In the "Setting" page, you can change the language, select the server location, and
determine if you want to automatically run the ASRock Live Update & APP Shop
on Windows startup.
English
45
3.4 Nahimic Audio
Nahimic audio software provides an incredible high definition sound technology which
boosts the audio and voice performance of your system. Nahimic Audio interface is
composed of four tabs: Audio, Microphone, Sound Tracker and Settings.
There are four functions in Nahimic audio :
No. Function Description
From this tab, you can mute the current audio device, choose
between four factory audio profiles, turn all audio effects
1 Audio
on/off, restores the current profile to its default settings and
access Surround Sound and various features.
From this tab, you can mute the current mic device, choose
between two factory mic profiles, turn/off all microphone
2 Microphone
effects, restore the current profile to its default settings, and
access Static Noise Suppression and various features.
The Sound Tracker provides a visual indication localizing

the sources of the sounds while in a game. These are
Sound
3 represented by dynamic segments pointing the direction
Tracker
English
of the sounds: the more opaque they are, the stronger the
sounds are.
From this tab, you can access all settings and information of
4 Settings
the software.
46
B460M Pro4
3.5 ASRock Polychrome SYNC

ASRock Polychrome SYNC is a lighting control utility specifically designed for unique indi-
viduals with sophisticated tastes to build their own stylish colorful lighting system. Simply by
connecting the LED strip, you can customize various lighting schemes and patterns, including
Static, Breathing, Strobe, Cycling, Music, Wave and more.
Connecting the LED Strip

Connect your RGB LED strips to the RGB LED Headers (RGB_LED1 / RGB_LED2) on the
motherboard.
RGB_LED1
RGB_LED2
1
12V G R B
1 B
R
G
12V
1. Never install the RGB LED cable in the wrong orientation; otherwise, the cable
may be damaged.
2. Before installing or removing your RGB LED cable, please power off your system
and unplug the power cord from the power supply. Failure to do so may cause dam-
ages to motherboard components.
1. Please note that the RGB LED strips do not come with the package.
English
2. The RGB LED header supports standard 5050 RGB LED strip (12V/G/R/B), with a
maximum power rating of 3A (12V) and length within 2 meters.
47
Connecting the Addressable RGB LED Strip
Connect your Addressable RGB LED strips to the Addressable LED Headers (ADDR_LED1 /
ADDR_LED2) on the motherboard.
ADDR_LED1
ADDR_LED2
GND
DO_ADDR
VOUT
1. Never install the RGB LED cable in the wrong orientation; otherwise, the cable may be
damaged.
2. Before installing or removing your RGB LED cable, please power off your system and
unplug the power cord from the power supply. Failure to do so may cause damages to
motherboard components.
1. Please note that the RGB LED strips do not come with the package.
2. The RGB LED header supports WS2812B addressable RGB LED strip (5V/Data/
GND), with a maximum power rating of 3A (5V) and length within 2 meters.
English
48
B460M Pro4
ASRock Polychrome SYNC Utility
Now you can adjust the RGB LED color through the ASRock Polychrome SYNC Utility.
Download this utility from the ASRock Live Update & APP Shop and start coloring your
PC style your way!
Drag the tab to customize your

preference.
Toggle on/off the

RGB LED switch
Select a RGB LED light effect
from the drop-down menu.
Sync RGB LED effects

for all LED regions of
the motherboard
English
49
Chapter 4 UEFI SETUP UTILITY
4.1 Introduction
This section explains how to use the UEFI SETUP UTILITY to configure your
system. You may run the UEFI SETUP UTILITY by pressing <F2> or <Del> right
after you power on the computer, otherwise, the Power-On-Self-Test (POST) will
continue with its test routines. If you wish to enter the UEFI SETUP UTILITY after
POST, restart the system by pressing <Ctl> + <Alt> + <Delete>, or by pressing the
reset button on the system chassis. You may also restart by turning the system off
and then back on.
Because the UEFI software is constantly being updated, the following UEFI setup
screens and descriptions are for reference purpose only, and they may not exactly
match what you see on your screen.
English
50
B460M Pro4
4.2 EZ Mode
The EZ Mode screen appears when you enter the BIOS setup program by default. EZ
mode is a dashboard which contains multiple readings of the system’s current status.
You can check the most crucial information of your system, such as CPU speed,
DRAM frequency, SATA information, fan speed, etc.
Press <F6> or click the "Advanced Mode" button at the upper right corner of the
screen to switch to "Advanced Mode" for more options.
No. Function
1 Help
2 Load UEFI Defaults
3 Save Changes and Exit
4 Discard Changes
5 Change Language
6 Switch to Advanced Mode
English
51
4.3 Advanced Mode
The Advanced Mode provides more options to configure the BIOS settings. Refer to
the following sections for the detailed configurations.
To access the EZ Mode, press <F6> or click the "EZ Mode" button at the upper right
corner of the screen.
4.3.1 UEFI Menu Bar

The top of the screen has a menu bar with the following selections:
Main For setting system time/date information
OC Tweaker For overclocking configurations
Advanced For advanced system configurations
Tool Useful tools
H/W Monitor Displays current hardware status
Security For security settings
Boot For configuring boot settings and boot priority
Exit Exit the current screen or the UEFI Setup Utility

English
52
B460M Pro4
4.3.2 Navigation Keys

Use < > key or < > key to choose among the selections on the menu bar, and
use < > key or < > key to move the cursor up or down to select items, then
press <Enter> to get into the sub screen. You can also use the mouse to click your
required item.
Please check the following table for the descriptions of each navigation key.
Navigation Key(s) Description
+ / - To change option for the selected items
<Tab> Switch to next function
<PGUP> Go to the previous page
<PGDN> Go to the next page
<HOME> Go to the top of the screen
<END> Go to the bottom of the screen
<F1> To display the General Help Screen
<F5> Add / Remove Favorite
<F7> Discard changes and exit the SETUP UTILITY
<F9> Load optimal default values for all the settings
<F10> Save changes and exit the SETUP UTILITY
<F12> Print screen
<ESC> Jump to the Exit Screen or exit the current screen

English
53
4.4 Main Screen
When you enter the UEFI SETUP UTILITY, the Main screen will appear and
display the system overview.
The availability and location of BIOS settings can be different for different models
and BIOS versions.
My Favorite
Display your collection of BIOS items. Press F5 to add/remove your favorite items.
English
54
B460M Pro4
4.5 OC Tweaker Screen

In the OC Tweaker screen, you can set up overclocking features.
Because the UEFI software is constantly being updated, the following UEFI setup
screens and descriptions are for reference purpose only, and they may not exactly
match what you see on your screen.
CPU Configuration
AVX Ratio Offset
AVX Ratio Offset specifies a negative offset from the CPU Ratio for AVX workloads.
AVX is a more stressful workload that lower the AVX ratio to ensure maximum
possible ratio for SSE workloads.
BCLK Spread Spectrum

Enable BCLK Spread Spectrum to reduce electromagnetic interference for passing
EMI tests. Disable to achieve higher clock speeds when overclocking.
BCLK Aware Adaptive Voltage

English
BCLK Aware Adaptive Voltage enable/disable. When enabled, pcode will be aware
of the BCLK frequency when calculating the CPU V/F curves. This is ideal for
BCLK OC to avoid high voltage overrides.
55
Boot Performance Mode
Select the performance state that the BIOS will set before OS handoff.
FCLK Frequency
Configure the FCLK Frequency.
Ring to Core Ratio Offset

Disable Ring to Core Ratio Offset so the ring and core can run at the same fre-
quency.
Intel SpeedStep Technology

Intel SpeedStep technology allows processors to switch between multiple frequen-
cies and voltage points for better power saving and heat dissipation.
Intel Turbo Boost Technology

Intel Turbo Boost Technology enables the processor to run above its base operating
frequency when the operating system requests the highest performance state.
Intel Speed Shift Technology

Enable/Disable Intel Speed Shift Technology support. Enabling will expose the
CPPC v2 interface to allow for hardware controlled P-sates.
Intel Thermal Velocity Boost Ratio Clipping

This service controls Core frequency reduction caused by high package tempera-
tures for processors that implement the Intel Thermal Velocity Boost (TVB) feature.
It is required to be disabled for supporting overclocking at frequencies higher than
the default max turbo frequency.
Intel Thermal Velocity Boost Voltage Optimizations

This service controls thermal based voltage optimizations for processors that
implment the Intel Thermal Velocity Boost (TVB) feature.
Long Duration Power Limit

Configure Package Power Limit 1 in watts. When the limit is exceeded, the CPU
ratio will be lowered after a period of time. A lower limit can protect the CPU and
save power, while a higher limit may improve performance.
English
Long Duration Maintained

Configure the period of time until the CPU ratio is lowered when the Long
Duration Power Limit is exceeded.
56
B460M Pro4
Short Duration Power Limit

Configure Package Power Limit 2 in watts. When the limit is exceeded, the CPU
ratio will be lowered immediately. A lower limit can protect the CPU and save
power, while a higher limit may improve performance.
CPU Core Current Limit

Configure the current limit of the CPU core. A lower limit can protect the CPU and
GT Current Limit
Configure the current limit of the GT slice. A lower limit can protect the CPU and
DRAM Configuration
Memory Information
Allows users to browse the serial presence detect (SPD) and Intel extreme memory profile
(XMP) for DDR4 modules.
DRAM Timing Configuration

DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s) inserted
and assign the appropriate frequency automatically.
Primary Timing
CAS# Latency (tCL)
The time between sending a column address to the memory and the beginning of the data
in response.
RAS# to CAS# Delay and Row Precharge (tRCDtRP)

RAS# to CAS# Delay : The number of clock cycles required between the opening of a row
of memory and accessing columns within it.
Row Precharge: The number of clock cycles required between the issuing of the precharge
command and opening the next row.
RAS# Active Time (tRAS)

English
The number of clock cycles required between a bank active command and issuing the
precharge command.
57
Command Rate (CR)
The delay between when a memory chip is selected and when the first active command can
be issued.
Secondary Timing
Write Recovery Time (tWR)
The amount of delay that must elapse after the completion of a valid write operation,
before an active bank can be precharged.
Refresh Cycle Time (tRFC)

The number of clocks from a Refresh command until the first Activate command to
the same rank.
RAS to RAS Delay (tRRD_L)

The number of clocks between two rows activated in different banks of the same
rank.
RAS to RAS Delay (tRRD_S)

The number of clocks between two rows activated in different banks of the same
rank.
Write to Read Delay (tWTR_L)

The number of clocks between the last valid write operation and the next read command to
the same internal bank.
Write to Read Delay (tWTR_S)

The number of clocks between the last valid write operation and the next read command to
the same internal bank.
Read to Precharge (tRTP)

The number of clocks that are inserted between a read command to a row pre-
charge command to the same rank.
Four Activate Window (tFAW)

The time window in which four activates are allowed the same rank.
English
CAS Write Latency (tCWL)

Configure CAS Write Latency.
58
B460M Pro4
Third Timing
tREFI
Configure refresh cycles at an average periodic interval.
tCKE
Configure the period of time the DDR4 initiates a minimum of one refresh
command internally once it enters Self-Refresh mode.
Turn Around Timing

tRDRD_sg
Configure between module read to read delay.
tRDRD_dg
tRDRD_dr
tRDRD_dd
tRDWR_sg
Configure between module read to write delay.
tRDWR_dg
tRDWR_dr
tRDWR_dd
tWRRD_sg
Configure between module write to read delay.
English
tWRRD_dg
59
tWRRD_dr
tWRRD_dd
tWRWR_sg
Configure between module write to write delay.
tWRWR_dg
tWRWR_dr
tWRWR_dd
Round Trip Timing

RTL Init Value
Configure round trip latency init value for round trip latency training.
IOL Init Value

Configure IO latency init value for IO latency training.
RTL (CH A)
Configure round trip latency for channel A.
RTL (CH B)
Configure round trip latency for channel B.
IOL (CH A)
Configure IO latency for channel A.
IOL (CH B)
Configure IO latency for channel B.
English
IOL Offset (CH A)

Configure IO latency offset for channel A.
60
B460M Pro4
IOL Offset (CH B)

Configure IO latency offset for channel B.
RFR Delay (CH A)

Configure RFR Delay for Channel A.
RFR Delay (CH B)

Configure RFR Delay for Channel B.
ODT Setting
ODT WR (A1)
Configure the memory on die termination resistors' WR for channel A1.
ODT WR (A2)
Configure the memory on die termination resistors' WR for channel A2.
ODT WR (B1)
Configure the memory on die termination resistors' WR for channel B1.
ODT WR (B2)
Configure the memory on die termination resistors' WR for channel B2.
ODT NOM (A1)

Use this to change ODT (CH A1) Auto/Manual settings. The default is [Auto].
ODT NOM (A2)

Use this to change ODT (CH A2) Auto/Manual settings. The default is [Auto].
ODT NOM (B1)

Use this to change ODT (CH B1) Auto/Manual settings. The default is [Auto].
ODT NOM (B2)

Use this to change ODT (CH B2) Auto/Manual settings. The default is [Auto].
ODT PARK (A1)

Configure the memory on die termination resistors' PARK for channel A1.
English
ODT PARK (A2)

Configure the memory on die termination resistors' PARK for channel A2.
61
ODT PARK (B1)
Configure the memory on die termination resistors' PARK for channel B1.
ODT PARK (B2)

Configure the memory on die termination resistors' PARK for channel B2.
COMP Setting
RCOMP0: DQ ODT (Read)
Default is 121.
RCOMP1: DQ /CLK Ron (Drive Strength)

Default is 75.
RCOMP2: CMD/CTL Ron (Drive Strength)

Default is 100.
DQ ODT Driving
Adjust ODT Driving for better signal. Default is 60.
DQ Driving
Adjust DQ Driving for better signal. Default is 26.
Command Driving
Adjust Command Driving for better signal. Default is 20.
Control Driving
Adjust Control Driving for better signal. Default is 20.
Clock Driving
Adjust Clock Driving for better signal. Default is 26.
DQ Slew Rate
Adjust DQ Slew Rate for better signal. Default is 59.
Command Slew Rate

Adjust Command Slew Rate for better signal. Default is 53 for IN, 89 for 2N.
English
Contorl Slew Rate

Adjust Control Slew Rate for better signal. Default is 53.
62
B460M Pro4
Clock Slew Rate

Adjust Clock Slew Rate for better signal. Default is 53.
MRS Setting
MRS tCL
Configure the tCL for Memory MRS MR0.
MRS tWRtRTP
Configure the tWRtRTP for Memory MRS MRC.
MRS tCWL
Configure the tCWL for Memory MRS MR2.
MRS tCCD_L
Configure the tCL for Memory MRS MR6.
Advanced Setting
ASRock Timing Optimization
Configure the fast path through the MRC.
Realtime Memory Timing

Configure the realtime memory timings.
[Enabled] The system will allow performing realtime memory timing changes after
MRC_DONE.
Command Tristate
Configure the Command Tristate Support.
Exit On Failure
Configure the Exit On Failure for MRC training steps.
Reset On Training Fail

Reset system if the MRC training fails.
MRC Fast Boot

English
Enable Memory Fast Boot to skip DRAM memory training for booting faster.
63
Voltage Configuration
CPU Core/Cache Voltage
Input voltage for the processor by the external voltage refulator.
GT Voltage
Configure the voltage for the integrated GPU.
DRAM Voltage
Use this to configure DRAM Voltage. The default value is [Auto].
DRAM Activating Power Supply

Configure the voltage for the DRAM Activating Power Supply.
PCH +1.0 Voltage

Configure the chipset voltage (1.0V).
VCCST Voltage
Configure the voltage for the VCCST.
VCCSA Voltage
Configure the voltage for the VCCSA.
Save User Default

Type a profile name and press enter to save your settings as user default.
Load User Default

Load previously saved user defaults.
Save User UEFI Setup Profile to Disk

It helps you to save current UEFI settings as an user profile to disk.
Load User UEFI Setup Profile from Disk

You can load previous saved profile from the disk.
English
64
B460M Pro4
4.6 Advanced Screen

In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, Storage Configuration, Intel(R) Thunderbolt,
Super IO Configuration, ACPI Configuration, USB Configuration and Trusted
Computing.
Setting wrong values in this section may cause the system to malfunction.
UEFI Configuration
UEFI Setup Style
Select the default mode when entering the UEFI setup utility.
Active Page on Entry

Select the default page when entering the UEFI setup utility.
Full HD UEFI
English
When [Auto] is selected, the resolution will be set to 1920 x 1080 if the monitor
supports Full HD resolution. If the monitor does not support Full HD resolution,
then the resolution will be set to 1024 x 768. When [Disable] is selected, the
resolution will be set to 1024 x 768 directly.
65
4.6.1 CPU Configuration
Intel Hyper Threading Technology

Intel Hyper Threading Technology allows multiple threads to run on each core, so
that the overall performance on threaded software is improved.
Active Processor Cores

Select the number of cores to enable in each processor package.
CPU C States Support

Enable CPU C States Support for power saving. It is recommended to keep C3, C6
and C7 all enabled for better power saving.
Enhanced Halt State (C1E)

Enable Enhanced Halt State (C1E) for lower power consumption.
CPU C3 State Support

Enable C3 deep sleep state for lower power consumption.

English

66
B460M Pro4
Package C State Support

Enable CPU, PCIe, Memory, Graphics C State Support for power saving.
CFG Lock
This item allows you to disable or enable the CFG Lock.
C6DRAM
Enable/Disable moving of DRAM contents to PRM memory when CPU is in C6
state.
CPU Thermal Throttling

Enable CPU internal thermal control mechanisms to keep the CPU from overheat-
ing.
Intel Virtualization Technology

Intel Virtualization Technology allows a platform to run multiple operating systems
and applications in independent partitions, so that one computer system can
function as multiple virtual systems.
Hardware Prefetcher
Automatically prefetch data and code for the processor. Enable for better
performance.
Adjacent Cache Line Prefetch

Automatically prefetch the subsequent cache line while retrieving the currently
requested cache line. Enable for better performance.
Software Guard Extensions (SGX)

Intel SGX is a set of new CPU instructions that can be used by applications to set
aside private regions of code and data.
English
67
4.6.2 Chipset Configuration
Primary Graphics Adapter

Select a primary VGA.
Above 4G Decoding
Enable or disable 64bit capable Devices to be decoded in Above 4G Address Space
(only if the system supports 64 bit PCI decoding).
VT-d
Intel® Virtualization Technology for Directed I/O helps your virtual machine
monitor better utilize hardware by improving application compatibility and
reliability, and providing additional levels of manageability, security, isolation, and
I/O performance.
SR-IOV Support
If system has SR-IOV capable PCIe Devices, this option Enables or Disables Single
Root IO Virtualization Support.
DMI Link Speed

Configure DMI Slot Link Speed. Auto mode is optimizing for overclocking.
English
PCIE1 Link Speed

Select the link speed for PCIE 1.
68
B460M Pro4
PCIE2 Link Speed

PCIE3 Link Speed

PCI Express Native Control

Select Enable for enhanced PCI Express power saving in OS.
PCIE ASPM Support

This option enables/disables the ASPM support for all CPU downstream devices.
PCH PCIE ASPM Support

This option enables/disables the ASPM support for all PCH PCIE devices.
DMI ASPM Support

This option enables/disables the control of ASPM on CPU side of the DMI Link.
PCH DMI ASPM Support

This option enables/disables the ASPM support for all PCH DMI devices.
Share Memory
Configure the size of memory that is allocated to the integrated graphics processor when
the system boots up.
IGPU Multi-Monitor
Select disable to disable the integrated graphics when an external graphics card is installed.
Select enable to keep the integrated graphics enabled at all times.
Inte(R) Ethernet Connection I219-V

Enable or disable the onboard network interface controller (Intel® I219V).
Onboard HD Audio
Enable/disable onboard HD audio. Set to Auto to enable onboard HD audio and
automatically disable it when a sound card is installed.
English
Front Panel
Enable/disable front panel HD audio.
69
Onboard HDMI HD Audio
Enable audio for the onboard digital outputs.
Onboard WAN Device

Use this item to enable or disable the onboard WAN device.
WAN Radio
Enable/disable the WiFi module's connectivity.
Bluetooth
Enable/disable the Bluetooth connectivity.
Deep Sleep
Configure deep sleep mode for power saving when the computer is shut down.
Restore on AC/Power Loss

Select the power state after a power failure. If [Power Off] is selected, the power will
remain off when the power recovers. If [Power On] is selected, the system will start
to boot up when the power recovers.
Turn On Onboard LED in S5

Turn on Onboard LED in the ACPI S5 state.
Restore Onboard LED Default

Restore Onboard LED default value.
RGB LED
This option enables/disables the RGB LED.
English
70
B460M Pro4
4.6.3 Storage Configuration
SATA Controller(s)
Enable/disable the SATA controllers.
SATA Mode Selection

AHCI: Supports new features that improve performance.
RAID: Combine multiple disk drives into a logical unit.
SATA Aggressive Link Power Management

SATA Aggressive Link Power Management allows SATA devices to enter a low
power state during periods of inactivity to save power. It is only supported by AHCI
mode.
Hard Disk S.M.A.R.T.

S.M.A.R.T stands for Self-Monitoring, Analysis, and Reporting Technology. It is a
monitoring system for computer hard disk drives to detect and report on various
indicators of reliability.
English
71
4.6.4 Intel(R) Thunderbolt
Discrete Thunderbolt(TM) Support

Enable or disable the Discrete Thunderbolt(TM) Support.
Thunderbolt Boot Support

Enabled to allow booting from Bootable devices which are present behind
Thunderbolt.
Thunderbolt Usb Support

Enabled to allow booting from Usb devices which are present behind Thunderbolt.
Titan Ridge Workaround for OSUP

Enable or disable Titan Ridge Workaround for OSUP.
Security Level
This item allows you to choose a security level for the Thunderbolt ports.
English
72
B460M Pro4
4.6.5 Super IO Configuration
PS2 Y-Cable
Enable the PS2 Y-Cable or set this option to Auto.
English
73
4.6.6 ACPI Configuration
Suspend to RAM
Select disable for ACPI suspend type S1. It is recommended to select auto for ACPI
S3 power saving.
PS/2 Keyboard S4/S5 Wakeup Support

Allow the system to be waked up by a PS/2 Keyboard in S4/S5.
PCIE Devices Power On

Allow the system to be waked up by a PCIE device and enable wake on LAN.
I219 LAN Power On

Allow the system to be waked up by the Onboard Intel LAN.
RTC Alarm Power On

Allow the system to be waked up by the real time clock alarm. Set it to By OS to let
it be handled by your operating system.
USB Keyboard/Remote Power On

English
Allow the system to be waked up by an USB keyboard or remote controller.
USB Mouse Power On

Allow the system to be waked up by an USB mouse.
74
B460M Pro4
4.6.7 USB Configuration
Legacy USB Support

Enable or disable Legacy OS Support for USB 2.0 devices. If you encounter USB
compatibility issues it is recommended to disable legacy USB support. Select UEFI
Setup Only to support USB devices under the UEFI setup and Windows/Linux
operating systems only.
XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The XHCI
ownership change should be claimed by XHCI driver.
English
75
4.6.8 Trusted Computing
Security Device Support

Enable or disable BIOS support for security device.
English
76
B460M Pro4
4.7 Tools
ASRock Polychrome RGB

Select LED lighting color.
UEFI Tech Service

Contact ASRock Tech Service if you are having trouble with your PC. Please setup
network configuration before using UEFI Tech Service.
Easy RAID Installer

Easy RAID Installer helps you to copy the RAID driver from the support CD to
your USB storage device. After copying the drivers please change the SATA mode to
RAID, then you can start installing the operating system in RAID mode.
SSD Secure Erase Tool

All the SSD's listed that supports Secure Erase function.
NVME Sanitization Tool

After you Sanitize SSD, all user data will be permanently destroyed on the SSD and
English
cannot be recovered.
Instant Flash
Save UEFI files in your USB storage device and run Instant Flash to update your
UEFI.
77
Internet Flash - DHCP (Auto IP), Auto
ASRock Internet Flash downloads and updates the latest UEFI firmware version
from our servers for you. Please setup network configuration before using Internet
Flash.
*For BIOS backup and recovery purpose, it is recommended to plug in your USB
pen drive before using this function.
Network Configuration
Use this to configure internet connection settings for Internet Flash.
Internet Setting
Enable or disable sound effects in the setup utility.
UEFI Download Server

Select a server to download the UEFI firmware.
English
78
B460M Pro4
4.8 Hardware Health Event Monitoring Screen

This section allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, fan
speed and voltage.
Fan Tuning
Measure Fan Min Duty Cycle.
Fan-Tastic Tuning
Select a fan mode for CPU Fan, or choose Customize to set 5 CPU temperatures and
assign a respective fan speed for each temperature.
CPU Fan 1 Setting

Select a fan mode for CPU Fan 1, or choose Customize to set 5 CPU temperatures
and assign a respective fan speed for each temperature.
CPU Fan 1 Step Up

Set the value of CPU Fan Step Up.
CPU Fan 1 Step Down

English
Set the value of CPU Fan Step Down.
CPU_FAN2 / W_PUMP Switch

Switch CPU_FAN2 / W_PUMP header function.
79
CPU Fan 2 Control Mode
Select DC/PWM mode for CPU Fan 2.
CPU Fan 2 Setting

Select a fan mode for CPU Fan, or choose Customize to set 5 CPU temperatures and assign
a respective fan speed for each temperature.
CPU Fan 2 Temp Source

Select a fan temperature source for CPU Fan 2.
CPU Fan 2 Step Up

Set the value of CPU Fan 2 Step Up.
CPU Fan 2 Step Down

Set the value of CPU Fan 2 Step Down.
CHA_FAN1 / W_PUMP Switch

Select Chassis Fan 1 or Water Pump mode.
Chassis Fan 1 Control Mode

Select PWM mode or DC mode for Chassis Fan 1.
Chassis Fan 1 Setting

Select a fan mode for Chassis Fan 1, or choose Customize to set 5 CPU temperatures
Chassis Fan 1 Temp Source

Select a fan temperature source for Chassis Fan 1.
Chassis Fan 1 Step Up

Set the value of Chassis Fan 1 Step Up.
Chassis Fan 1 Step Down

Set the value of Chassis Fan 1 Step Down.
CHA_FAN2 / W_Pump Switch

English

80
B460M Pro4




CHA_FAN3 / W_PUMP Switch






Case Open Feature

Enable or disable Case Open Feature to detect whether the chassis cover has been
removed.
English
81
4.9 Security Screen
In this section you may set or change the supervisor/user password for the system.
You may also clear the user password.
Supervisor Password
Set or change the password for the administrator account. Only the administrator
has authority to change the settings in the UEFI Setup Utility. Leave it blank and
press enter to remove the password.
User Password
Set or change the password for the user account. Users are unable to change the
settings in the UEFI Setup Utility. Leave it blank and press enter to remove the
password.
Secure Boot
Use this item to enable or disable support for Secure Boot.
Intel(R) Platform Trust Technology

Enable/disable Intel PTT in ME. Disable this option to use discrete TPM Module.
English
82
B460M Pro4
4.10 Boot Screen

This section displays the available devices on your system for you to configure the
boot settings and the boot priority.
Fast Boot
Fast Boot minimizes your computer's boot time. In fast mode you may not boot
from an USB storage device. The VBIOS must support UEFI GOP if you are using
an external graphics card. Please notice that Ultra Fast mode will boot so fast that
the only way to enter this UEFI Setup Utility is to Clear CMOS or run the Restart to
UEFI utility in Windows.
Boot From Onboard LAN

Allow the system to be waked up by the onboard LAN.
Setup Prompt Timeout

Configure the number of seconds to wait for the setup hot key.
Bootup Num-Lock
Select whether Num Lock should be turned on or off when the system boots up.
Boot Beep
English
Select whether the Boot Beep should be turned on or off when the system boots up. Please
note that a buzzer is needed.
83
Full Screen Logo
Enable to display the boot logo or disable to show normal POST messages.
AddOn ROM Display

Enable AddOn ROM Display to see the AddOn ROM messages or configure the
AddOn ROM if you've enabled Full Screen Logo. Disable for faster boot speed.
Boot Failure Guard Message

If the computer fails to boot for a number of times the system automatically restores
the default settings.
CSM (Compatibility Support Module)
CSM
Enable to launch the Compatibility Support Module. Please do not disable unless
you’re running a WHCK test.
Launch PXE OpROM Policy

Select UEFI only to run those that support UEFI option ROM only. Select Legacy
only to run those that support legacy option ROM only. Select Do not launch to not
English
execute both legacy and UEFI option ROM.
Launch Storage OpROM Policy

Select UEFI only to run those that support UEFI option ROM only. Select Legacy
84
B460M Pro4
only to run those that support legacy option ROM only. Select Do not launch to not
execute both legacy and UEFI option ROM.
Other PCI Device ROM Priority

For PCI devices other than Network. Mass storage or Video defines which OpROM
to launch.
English
85
4.11 Exit Screen
Save Changes and Exit

When you select this option the following message, “Save configuration changes
and exit setup?” will pop out. Select [OK] to save changes and exit the UEFI SETUP
UTILITY.
Discard Changes and Exit

When you select this option the following message, “Discard changes and exit
setup?” will pop out. Select [OK] to exit the UEFI SETUP UTILITY without saving
any changes.
Discard Changes
When you select this option the following message, “Discard changes?” will pop
out. Select [OK] to discard all changes.
Load UEFI Defaults

Load UEFI default values for all options. The F9 key can be used for this operation.
Launch EFI Shell from filesystem device

Copy shellx64.efi to the root directory to launch EFI Shell.
English
86
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support request
form at https://event.asrock.com/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District,
Taipei City 112, Taiwan (R.O.C.)
ASRock EUROPE B.V.

Bijsterhuizen 11-11
6546 AR Nijmegen
The Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.

13848 Magnolia Ave, Chino, CA91710
U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name: ASRock Incorporation
Address: 13848 Magnolia Ave, Chino, CA91710
Phone/Fax No: +1-909-590-8308/+1-909-590-1026
hereby declares that the product
Product Name : Motherboard
Model Number : B460M Pro4
Conforms to the following specifications:
FCC Part 15, Subpart B, Unintentional Radiators
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Representative Person’s Name: James
Signature :
Date : May 12, 2017

EU Declaration of Conformity

For the following equipment:
Motherboard
(Product Name)
B460M Pro4 / ASRock
(Model Designation / Trade Name)
ASRock Incorporation
(Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.)
(Manufacturer Address)
‫ ڛ‬EMC —Directive 2014/30/EU (from April 20th, 2016)

☐ EN 55022:2010/AC:2011 Class B ‫ ڛ‬EN 55024:2010/A1:2015
‫ ڛ‬EN 55032:2012+AC:2013 Class B ‫ ڛ‬EN 61000-3-3:2013
‫ ڛ‬EN 61000-3-2:2014
☐ LVD —Directive 2014/35/EU (from April 20th, 2016)

☐ EN 60950-1 : 2011+ A2: 2013 ☐ EN 60950-1 : 2006/A12: 2011
‫ ڛ‬RoHS — Directive 2011/65/EU

‫ ڛ‬CE marking
(EU conformity marking)
ASRock EUROPE B.V.

(Company Name)
Bijsterhuizen 1111 6546 AR Nijmegen The Netherlands
(Company Address)
Person responsible for making this declaration:
(Name, Surname)
A.V.P
(Position / Title)
May 15, 2020
(Date)
P/N: 15G062210001AK V1.1

B460M Pro4 Manual

Uploaded by

Copyright:

Available Formats

B460M Pro4 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

B460M Pro4 Manual

Uploaded by

Copyright:

Available Formats

Version 1.

CALIFORNIA, USA ONLY

ASRock Website: http://www.asrock.com

1.3 Motherboard Layout 7

1.4 I/O Panel 9

2.2 Installing the CPU Fan and Heatsink 14

2.3 Installing Memory Modules (DIMM) 15

2.4 Expansion Slots (PCI Express Slots) 17

2.5 Jumpers Setup 18

2.6 Onboard Headers and Connectors 19

2.7 CrossFireX TM and Quad CrossFireX TM Operation Guide 24

2.7.1 Installing Two CrossFireX TM-Ready Graphics Cards 24

2.7.2 Driver Installation and Setup 26

2.8 M.2 WiFi/BT Module Installation Guide 27

2.9 M.2_SSD (NGFF) Module Installation Guide (M2_1) 29

2.10 M.2_SSD (NGFF) Module Installation Guide (M2_2) 32

Chapter 3 Software and Utilities Operation 36

3.2 ASRock Motherboard Utility (A-Tuning) 37

3.3 ASRock Live Update & APP Shop 40

3.3.3 BIOS & Drivers 44

3.4 Nahimic Audio 46

3.5 ASRock Polychrome SYNC 47

Chapter 4 UEFI SETUP UTILITY 50

4.3 Advanced Mode 52

4.3.1 UEFI Menu Bar 52

4.3.2 Navigation Keys 53

4.4 Main Screen 54

4.5 OC Tweaker Screen 55

4.6 Advanced Screen 65

4.6.1 CPU Configuration 66

4.6.2 Chipset Configuration 68

4.6.3 Storage Configuration 71

4.6.4 Intel(R) Thunderbolt 72

4.6.5 Super IO Configuration 73

4.6.6 ACPI Configuration 74

4.6.7 USB Configuration 75

4.6.8 Trusted Computing 76

4.9 Security Screen 82

4.10 Boot Screen 83

4.11 Exit Screen 86

In this documentation, Chapter 1 and 2 contains the introduction of the

1.1 Package Contents

Platform • Micro ATX Form Factor

CPU • Supports 10th Gen Intel® CoreTM Processors (Socket 1200)

Chipset • Intel® B460

Memory • Dual Channel DDR4 Memory Technology

Expansion • 2 x PCI Express 3.0 x16 Slots (PCIE1/PCIE3: single at x16

Audio • 7.1 CH HD Audio with Content Protection (Realtek

• Individual PCB Layers for R/L Audio Channel

Rear Panel • 1 x Antenna Bracket

Storage • 6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,

Connector • 1 x SPI TPM Header

BIOS • AMI UEFI Legal BIOS with multilingual GUI support

OS • Microsoft® Windows® 10 64-bit

* For detailed product information, please visit our website: http://www.asrock.com

1.3 Motherboard Layout

DDR4_A1 (64 bit, 288-pin module)

DDR4_B1 (64 bit, 288-pin module)

DDR4_B2 (64 bit, 288-pin module)

USB 3.2 Gen1