CSS12 1st WEEK6 SSLM Evaluated

TVL COMPUTER SYSTEMS SERVICING 12
Name: ______________________________________ Date: ____________________
Grade: ______________________________________ Section: ___________________
Semester: 1st Week: 6 SSLM No. 6

ELC(s): Set router/Wi-fi/wireless access point/repeater configuration
Objectives:
• Configure Wireless Access Point; and
• Configure Routers as Access Points;
➢ Title of Textbook/LM to Study: SLM – TVL CSS 12
➢ Chapter: ___ Pages: ___ Topic: Wireless Network Configuration
Let Us Discover
What is a DHCP?
We have learned that a router is capable of assigning IP addresses to the
devices connected to it. It is done through DHCP or Dynamic Host Configuration
Protocol. It is a system that assigns dynamic IP addresses to devices on a network.
Whenever a device connects to the router, it will be assigned a dynamic IP address.
To configure the DHCP, login to the router and go to DHCP menu.
In this setting, we set the start IP

address to 192.168.1.100, which
means that the first device that will
connect to the router will have the IP
address 192.168.1.100, and the last
device will have the 192.168.1.199 IP
address. In short, the router will cater
to 100 devices on its network.
192.168.1.2 to 192.168.1.99 will not
be assigned as well as 192.168.1.200
to 192.168.1.255.
You can customize these IP

addresses depending on your preference.
If you are having these setups below, you need to have dynamic IP addresses
for your workstations. It would help if you allow the router to assign an IP address
GSC-CID-LRMS-ESSLM, v.r. 03.00, Effective June 9, 2021

for your network for the device to identify which device the data should be
transmitted to.
Room 1 Room 2 (adjacent to room 1)
Router Switch crossover Ethernet cable Switch
Room 1 Room 2 (adjacent to room 1)
Switch Straight through LAN cable Straight through LAN cable

Router Switch
That is why you need to set “Obtain an IP address automatically in your

network settings.” Below is how you do it to every device that will connect to your
router.
1. Go to Control Panel > Network and Internet > Network and Sharing Center
2. Click Properties
3. Double click Internet Protocol Version 4 (TCP/IPv4) or
4. Click Properties button
5. Choose Obtain an IP address automatically and
6. Click OK button
5
3
2 4
Congratulations on setting up your wireless network where mobile devices can

now connect to the internet as well.
Your next concern now is how to connect mobile (wireless) devices on the same
network in areas that are a bit farther than the router? Usually, routers can reach
around 42 meters indoor and 92 meters outdoor. The router signal can no longer
reach wireless devices farther than those. How will you address this issue?
It is time for you to use Wireless Access Points.
What is a Wireless Access Point?
The concept of Wireless Access Points (WAP) is the
same way that repeaters do. Only that, they give access
to “wireless” devices. It relays data between a wired
network and wireless devices. While a router is enough
for a home wireless setting due to its small coverage,
access points are used in medium to large companies
where wireless access is needed in a much more
extensive coverage where a router’s signal can no longer reach.
Take a look at the setup below:
In this setup, wireless devices on the
third floor can no longer be reached by the
router’s signal on the first floor. However,
with the presence of the wireless access
Third Floor point, they will now be able to connect.
These access points are wired to the
company’s router and provide a signal on its
area of coverage.
The router assigns IP addresses to the
different devices connected to it while the
Second Floor WAP (Wireless Access Points) does not.
Configuring the Access Point
Router The same way that you set up the router

First Floor
is pretty much the same as the access point.
Before you configure your WAP take note

on the following:
• Make sure you are not connected to any network (wired or wireless) before
you configure the Access Point.
• Make sure you assign DHCP in your router to start assigning IP addresses
that do not include the IP address that you will assign to your access point.
In your case earlier, you started with 192.168.1.100 to be assigned to the
first device connected to the network until 192.168.1.199. Therefore,
192.168.1.2 to 192.168.1.99 and 192.168.1.200 to 192.168.1.255 are not
assigned IP addresses. You can use any of it to be assigned to your Access
Point. Again, you can customize these according to your preference.
1. Connect Access Point to your Computer using the LAN cable. (Make sure you
are not connected to other networks)
2. Determine the IP address of your Access Point (You already learned two
methods to do this).
3. Once you know the IP address of your Access Point, go to a browser and type
it. You will then be brought to the Access Point’s Login portal. And Login
using the default User Name and Password found at the back of your Access
Point. (For security reasons, you may change this)
Note: Online practice without using the actual device. TP Link emulator link below.
https://emulator.tp-link.com/EMULATOR_wr802nv2_en/userRpm/Index.htm
1. In the status
menu of your
Access Point,
you will see
that the
Operation Mode
of this device is
“Access Point.”
2. Then you need to assign a Static IP address for your Access Point. Click on the Network
Menu and change the IP address and the Gateway, then the click Save button.
Remember that in your router, the IP address 192.168.1.2 is not assigned to any
device that may connect to the router. The gateway is the IP address of your router, where
this access point will be connected to.
3. Then click the Wireless Menu

and change the Wireless
Network Name according to
your preference. It is the
name of the wireless network
that the second-floor wireless
devices will be connected to.
Then Click Save.
4. Change the password for your

wireless network, or you may
disable this if you want all the
wireless devices to connect
without having to type in any
password. Then Click Save
Button.
5. Lastly, make sure that your
DHCP server is disabled.
Then click the save button
since Access Points are just
portals of signals, and it is the
router’s job to assign IP
addresses to the devices.
Then unplug the LAN cable from your computer and connect it to the router.
Congratulations for setting up your Access Point.
Routers as Access Points
You can turn your routers as access points

too. Just follow the configurations below.
1. Turn your router’s Working Mode into
“Access Point.”
2. Assign a Static IP that is not assigned by the
main router.
3. Make the main router’s IP address as the
gateway.
4. Make sure you disable the
DHCP server.
Then you are green to go!
Let Us Try
Directions: Write T if the statement is true and F if it is false.

1. Each time a device connects to the network, it maintains the previously
assigned IP address.
2. It is required that all access points must have a password to connect to the
network.
3. Access points must not be connected to the router while configuring it.
4. Windows 10 has a default firewall turned on.
5. Switches can be wireless access points too.
Let Us Do
Directions: Briefly discuss the steps of the following (Use another sheet of paper if
necessary):
1. Configuring Wireless Access Point
______________________________________________________________________________
______________________________________________________________________________
2. Configuring Routers as Access Points
Let Us Apply
______________________________________________________________________________
______________________________________________________________________________
Directions: Briefly answer the following questions. Provide extra sheet of paper if
necessary.
Putting in mind the concept of repeaters and making a more extensive Local
Area network, create the diagram or network design of a Five-Floor Hotel
with the following considerations:
Floor 1 – Reception/Office area with 15 computers
Floor 2 and 3 – Guest rooms with only wireless devices
Floor 4 – Entertainment Floor with Internet Cafe Pool and a park
Floor 5 – Guest rooms with only wireless devices
Show the cable connections, the placements of different devices and the IP
addresses of the major devices (not including the wireless devices).
Rubrics
The performance of the learners will be rated based on the following criteria.
Criteria 5 4 3 2 1
Excellent Very Satisfactory Moderately Good
Satisfactory Satisfactory
Clarity of concept
Knowledge application
Neatness of design
References
SLM - TVL - Computer Systems Servicing Quarter 2 – Self-Learning Module: Module 3:

Wireless Network Configuration ; Pagalan, et al. pages 10-14
SSLM Development Team

Writer: Donabella P. Pagalan
Content Editor: Wilma M. Abendan, Marie-Berthe P. Pabale
LR Evaluator:
Illustrator: Donabella P. Pagalan
Creative Arts Designer: Reggie D. Galindez
Education Program Supervisor EPP/TLE/TVL: Amalia C. Caballes
Education Program Supervisor – Learning Resources: Sally A. Palomo
Curriculum Implementation Division Chief: Juliet F. Lastimosa
Asst. Schools Division Superintendent: Carlos G. Susarno, Ph. D.
Schools Division Superintendent: Romelito G. Flores, CESO V
Answer Key
Let us try
1. F
2. F
3. T
4. T
5. F

CSS12 1st WEEK6 SSLM Evaluated

Uploaded by

Copyright:

Available Formats

CSS12 1st WEEK6 SSLM Evaluated

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CSS12 1st WEEK6 SSLM Evaluated

Uploaded by

Copyright:

Available Formats

TVL COMPUTER SYSTEMS SERVICING 12

Name: ______________________________________ Date: ____________________

Grade: ______________________________________ Section: ___________________

Semester: 1st Week: 6 SSLM No. 6

To configure the DHCP, login to the router and go to DHCP menu.

In this setting, we set the start IP

You can customize these IP

GSC-CID-LRMS-ESSLM, v.r. 03.00, Effective June 9, 2021

Router Switch crossover Ethernet cable Switch

Room 1 Room 2 (adjacent to room 1)

Switch Straight through LAN cable Straight through LAN cable

That is why you need to set “Obtain an IP address automatically in your

Congratulations on setting up your wireless network where mobile devices can

Configuring the Access Point

Router The same way that you set up the router

Before you configure your WAP take note

3. Then click the Wireless Menu

4. Change the password for your

Congratulations for setting up your Access Point.

Routers as Access Points

You can turn your routers as access points

Directions: Write T if the statement is true and F if it is false.

SLM - TVL - Computer Systems Servicing Quarter 2 – Self-Learning Module: Module 3:

SSLM Development Team

You might also like

Name: __________________ Date:

Grade: ____________________ Section: _