AGRICULTURAL

ENGINEERING
COMPREHENSIVE BOARD
EXAM REVIEWER
Agricultural Power, Machinery, and
Allied Subjects

by

Engr. Alexis T. Belonio

Department of Agricultural Engineering and
Environmental Management
College of Agriculture
Central Philippine University
Iloilo City

TGIM Review Center

Institute of Agricultural Engineering
TGIM Corporation
Manila
2004
 Agricultural Power and Machinery

1. Depth of plowing for common paddy field.

a. 5 to 10 cm
b. 10 to 15 cm
c. 15 to 20 cm
d. None of the above
2. Depth of cultivated topsoil layer big practiced in modern upland farming
a. 0 to 10 cm
b. 10 to 20 cm
c. 20 cm to 30 cm
d. None of the above
3. In paddy field plowing operation using a four wheel tractor, which of the
following is true:
a. Smaller plots are much efficient to plow than larger plots.
b. Larger plots are much efficient to plow than smaller plots.
c. Smaller or larger plots have the same plowing efficiency.
d. None of the above
4. It is a wheel less cultivator that is used for domestic gardening.
a. Motor tiller
b. Power tiller
c. Puddling-type floating tiller
d. None of the above
5. It is the percentage ratio of the time a machine is effectively operating to the total
time the machine is committed to the operation.
a. Operating time efficiency
b. Time efficiency
c. Effective time efficiency
d. All of the above
6. Machine performance is determined by _____________.
a. the rate and quality at which the operations are accomplished
b. the speed to accomplished the given operation
c. the power needed in accomplishing the given operation
d. None of the above
7. The rate of machine performance is usually expressed in terms of _______.
a. quantity per unit time
b. quality per unit time
c. speed per unit time
d. All of the above
8. It is the time spent by the machine in the field to replace or renew pars that have
become inoperative.
a. Maintenance time
b. Machine adjustment time
c. Repair time
d. All of the above
9. It is the time used in refueling, lubricating, tightening of chain, etc of the machine.
a. Maintenance time
b. Machine adjustment time
c. Repair time
d. All of the above
10. Which of the following statement is true?
a. Theoretical field capacity is less than effective field capacity.
b. Effective field capacity is more than effective field capacity.
c. Theoretical field capacity is equal to the effective field capacity.
d. None of the above
11. Which of the following statement is true?
a. Field efficiency decreases with the increase in theoretical field capacity.
b. Field efficiency decreases with the increase in effective field capacity.
c. Field efficiency does not increase with the increase in theoretical field
capacity.
d. None of the above
12. It is the radius of the circle within which the implement can make its shortest run
in the field.
a. Radius of run
b. Minimum turning distance
c. Turning radius
d. None of the above
13. It is the travel of the machine across or around a field from a selected starting
point adjacent to the first.
a. Round
b. Trip
c. Operation
d. None of the above
14. One half of the travel from one end of the field to the other.
a. Round
b. Trip
c. Operation
d. None of the above
15. It describes the practice of dividing the field into sub-areas and operating on these
sub-areas individually.
a. Operating in lands
b. Field operation
c. Field division
d. None of the above
16. __________ unprocessed area that provide room for making turns.
a. Headland
b. Turn strips
c. Turning radius
d. None of the above
17. Field operating pattern where it has a trips that parallel with each other, are
incremented successively by the operating width of the implement, and initiated at
one boundary and terminated at the opposite.
a. Circuitous pattern
b. Headland pattern
c. Alternation pattern
d. None of the above
18. It describes the operation of the implement operation paralleling each land’s
boundaries and is commonly describes as “going around the field.”
a. Circuitous pattern
b. Headland pattern
c. Alternation pattern
d. None of the above
19. It is sometimes used in processing established row crops and a modification of
continuous pattern.
a. Circuitous pattern
b. Headland pattern
c. Alternation pattern
d. None of the above
20. Pattern efficiency of headland pattern in a square field.
a. 93.0%
b. 95.7%
c. 84.0%
d. None of the above
21. Which of the following is not a source of energy for farming?
a. Solar energy
b. Wind energy
c. Biomass energy
d. All of the
e. None of the above
22. A conventional source of energy.
a. Human power
b. Draft Animal
c. Fossil fuel
d. All of the above
e. None of the above
23. A non-conventional sources of energy
a. Biomass
b. Solar
c. Wind
d. All of the above
e. None of the above
24. A steam engine is an example of ______________.
a. an internal combustion engine
b. an external combustion engine
c. a dual combustion engine
d. None of the above
25. A constant volume cycle engine.
a. Gasoline engine
b. Diesel engine
c. Steam engine
d. None of the above
26. A constant pressure cycle
a. Gasoline engine
b. Diesel engine
c. Steam engine
d. None of the above
27. An internal combustion engine that produces two power stroke in two revolution
of the crankshaft.
a. Four-stroke cycle engine
b. Two-stroke cycle engine
c. One-stroke cycle engine
d. None of the above
28. A fuel commonly used for external combustion engine.
a. Gasoline
b. Diesel
c. Biomass
d. None of the above
29. Fuel used for constant volume cycle internal combustion engine.
a. Gasoline
b. Diesel
c. Biomass
d. None of the above
30. Fuel used for constant pressure cycle internal combustion engine.
a. Gasoline
b. Diesel
c. Biomass
d. None of the above
31. How many fuel injection pump are there in 4 cylinder four stroke cycle diesel
engine?
a. 1
b. 2
c. 4
d. None of the above
32. How many fuel injection pump are there in 4 cylinder four stroke cycle gasoline
engine?
a. 1
b. 2
c. 4
d. None of the above
33. Which of the following do belong to crop maintenance equipment?
a. Plow and harrow
b. Weeder
c. Sprayer
d. All of the above
34. Compression ring is usually located ____________ .
a. on top of the oil ring
b. beneath the oil ring
c. on the same position with the oil ring
d. None of the above
35. Engine piston displacement will increase if the ____________ .
a. piston diameter is increased
b. piston stroke is increased
c. All of the above
d. None of the above
36. Increasing the engine clearance volume will _____________ .
a. increase the compression ratio
b. decrease the compression ratio
c. have the same compression ratio
d. None of the above
37. A 16-valve diesel engine usually have ___________ .
a. a single-piston cylinders
b. a six-piston cylinders
c. an eight-piston cylinders
d. None of the above
38. Ignition of fuel in a gasoline fuel engine usually starts when the piston is
__________ .
a. at the top dead center
b. moving downward the bottom dead center
c. approaching the top dead center
d. None of the above
39. At the downward stroke of a two-stroke cycle gasoline engine, which of the
following events takes place?
a. Power, Exhaust, and Intake
b. Compression, Exhaust, and Power
c. Compression, Power, and Intake
40. Compression pressure for small gasoline engine.
a. 40 to 70 psi
b. 75 to 125 psi
c. 150 to 410 psi
d. None of the above
41. A process of providing the engine with additional amount of air and fuel using a
small turbine propelled by engine exhaust gas to increase power by about 30%.
a. Turbo charging
b. Supercharging
c. Air and fuel injecting
d. None of the above
42. Which of the following engine requires frequent maintenance?
a. Compression ignition engine
b. Spark-ignition engine
c. Air cooled compression ignition engine
d. All of the above
43. The direction of a crawler-type tractor can be maneuvered by __________
a. stopping the engine
b. stopping one of its wheels
c. using the stirring wheel
d. None of the above
44. A crawler-type tractor of the same weight provides __________ soil compacting
pressure than wheel type tractor.
a. higher
b. lower
c. the same
d. None of the above
45. Power implements are usually connected to the ________ of the tractor.
a. wheel axle drive
b. power take-off drive
c. front wheel drive
d. None of the above
46. Turbo charging tractor engine will increase the power output approximately by
_____ .
a. 10 – 20 %
b. 20 - 30 %
c. 30 – 40 %
d. None of the above
47. Integral mounted implement are usually attached to the tractor through a ______.
a. single point hitch system of the tractor
b. double-hitch system of the tractor
c. three-point hitch system of the tractor
d. None of the above
48. A semi-integral mounted type implements are usually attached to the tractor
through a _________ .
a. single point hitch system of the tractor
b. double-hitch system of the tractor
c. three-point hitch system of the tractor
d. None of the above
49. A trailing-type implements are usually attached to the tractor through a
_________ .
a. single point hitch system of the tractor
b. double-hitch system of the tractor
c. three-point hitch system of the tractor
d. None of the above
50. Seed produced by the Seed Production and Health Division form UP ad certified
100% pure by the Seed Quality Control Services of the Bureau of Plant Industry.
a. Certified Seeds
b. Registered Seeds
c. Foundation Seeds
d. Breeder Seeds
e. None of the above
51. Seed produced from breeder seeds and distributed to all members of the Seed Net
and selected seed producers in every province for further multiplication.
a. Certified Seeds
b. Registered Seeds
c. Foundation Seeds
d. Breeder Seeds
e. None of the above
52. Seed produced from Foundation Seed and being distributed to all accredited seed
producers for mass production.
a. Certified Seeds
b. Registered Seeds
c. Foundation Seeds
d. Breeder Seeds
e. None of the above
53. Seed produced from the Registered Seed by accredited seed producers and
distributed to farmers for commercial production.
a. Certified Seeds
b. Registered Seeds
c. Foundation Seeds
d. Breeder Seeds
e. None of the above
54. Machine operation in which there are two or more machines performing their own
respective operation simultaneously.
a. Individual operation
b. Parallel operation
c. Series operation
d. None of the above
55. Machine operation in which there are two or more machines performing their own
respective operation in sequence.
a. Individual operation
b. Parallel operation
c. Series operation
d. None of the above
56. Machine operation in which one or more similar machines are operated as one
unit.
a. Individual operation
b. Parallel operation
c. Series operation
d. None of the above
57. It is the amount paid for hiring equipment and operator services to perform a
certain task.
a. Machine fixed cost
b. Machine variable cost
c. Machine custom cost
d. None of the above
58. It is the useful service life of the machine before it becomes unprofitable for its
original purpose due to obsolescence or wear.
a. Machine economic life
b. Machine life span
c. Machine service life
d. None of the above
59. A kilogram fuel consumed by an engine per hr per amount of brake power is the
_______.
a. fuel consumption rate
b. specific fuel consumption rate
c. specific fuel
d. None of the above
60. A tractor type designed for operation with advantage under trees.
a. Standard tractor
b. All-purpose row crop tractor
c. Orchard tractor
d. All of the above
61. Tractor size is determined by _______________________.
a. weight, horsepower, and size and number of wheels
b. implement capacity, weight, and size and number of wheels
c. weight, horsepower, and implement capacity
d. All of the above
62. Which of the following is not driven by PTO shaft?
a. Rotary tiller
b. Power harrow
c. Moldboard plow
d. All of the above
63. A three-bottom disc plow is to be connected to a tractor, what tractor hitch system
would your recommend for the plow?
a. Drawn bar hitch type
b. Semi-mounted type
c. Direct mounted type
d. None of the above
64. It is a circular flat tool placed ahead of a plow used to cut plant material and soil.
a. Jointer
b. Pinion plow
c. Coulter
d. None of the above
65. It is the minimum vertical distance between the soil surface and a potentially
obstructing machine element.
a. Vertical clearance
b. Machine height
c. Ground clearance
d. All of the above
66. Angle in vertical plane perpendicular to the direction of travel between the tool
axis and the soil surface.
a. Tilt angle
b. Side angle
c. Lift angle
d. None of the above
67. Angle in the soil surface plane perpendicular to the direction of travel between the
tool axis and the line which is perpendicular to the direction of travel.
a. Tilt angle
b. Side angle
c. Lift angle
d. None of the above
68. Angle in vertical plane parallel to the direction of travel between a tool axis and
the soil surface.
a. Tilt angle
b. Side angle
c. Lift angle
d. None of the above
69. A trench left when the plow bottom cuts and turns the furrow slice.
a. Back furrow
b. Dead furrow
c. Furrow
d. All of the above
70. A raised ridge left at the center of the strip of land when plowing started center to
center.
a. Back furrow
b. Dead furrow
c. Furrow
d. All of the above
71. An open trench left between the adjacent strips of land after finishing the plowing
operation.
a. Back furrow
b. Dead furrow
c. Furrow
d. All of the above
72. It is the peak of the turned furrow slice.
a. Furrow crown
b. Furrow slice
c. Furrow wall
d. None of the above
73. A soil mass cut, lifted , pulverized, inverted, and thrown to one side of the plow
bottom.
a. Furrow crown
b. Furrow slice
c. Furrow wall
d. None of the above
74. It is the undisturbed or broken side of the furrow.
a. Furrow crown
b. Furrow slice
c. Furrow wall
d. None of the above
75. It refers to the arrangement of soil particles in the soil layer.
a. Soil texture
b. Soil structure
c. Soil moisture
d. All of the above
76. It refers to the relative proportion of the soil separates in a given soil.
a. Soil texture
b. Soil structure
c. Soil moisture
d. All of the above
77. Which of the following do not belong to seeder parts.
a. Furrow opener
b. Metering device
c. Covering device
d. Seed tube
e. None of the above
f. All of the above
 78. Which of the following statement is true?
a. The velocity of the flat belt of a reaper is faster than its forward velocity.
b. The velocity of the flat belt of a reaper is slower than its forward velocity.
c. The velocity of the flat belt of a reaper is the same with the forward
velocity.
d. None of the above
e. above
79. Which of the following statement is true?
a. The velocity of the knife of a reaper is faster than its forward velocity.
b. The velocity of the knife of a reaper is slower than its forward velocity.
c. The velocity of the knife of a reaper is the same with the forward velocity.
d. None of the above
80. The difference between a stripper and a reaper is that __________________.
a. the stripper cuts the panicle during harvesting
b. the reaper detach the grain during harvesting
c. the stripper detach the grains while the reaper cuts the panicle during
harvesting
d. None of the above
81. A drum seeder is highly suitable for rice seeds that was _______________ .
a. freshly stored before planting
b. pre-germinated before planting
c. milled before planting
d. All of the above
82. During seeding and planting, which of the crop production activities is
simultaneously in operation?
a. Weeding
b. Irrigating
c. Fertilizing
d. Spraying
e. None of the above
83. The metering device of a seeder basically is used to uniformly feed the seed into
the _______________ .
a. covering device
b. seed tube
c. furrow opener
d. None of the above
84. Part of a rice transplanter that places the seedlings into the prepared paddy field.
a. Feed tray
b. Picker
c. Handle
d. None of the above
85. If you are an engineer to mechanize a lowland rice farm that is usually flooded,
what primary tillage implement would you recommend?
a. Spiral-type tiller
b. Disc-type tiller
c. Puddling-type tiller
d. None of the above
86. Which of the following primary tillage equipment for small rice farm with higher
field capacity?
a. Disc plow
b. Spiral plow
c. Puddling-type tiller
d. Comb harrow
e. None of the above
87. Heavy-duty type power tiller basically consists of _______ axles?
a. single
b. double
c. triple
d. None of the above
88. A type of disk harrow that is not directly parallel in position with the tractor
during operation.
a. Single action disk harrow
b. Double action disk harrow
c. Offset disk harrow
d. All of the above
89. The power that is required in pulling an implement.
a. Brake horsepower
b. Drawbar horsepower
c. Power takeoff horsepower
d. All of the above
90. The power that is required in driving a pump shaft.
a. Brake horsepower
b. Drawbar horsepower
c. Power takeoff horsepower
d. All of the above
91. The power available at the engine shaft used in driving machinery.
a. Brake horsepower
b. Drawbar horsepower
c. Power takeoff horsepower
d. All of the above
92. The power required in driving power harrows, rotary tiller, and other related
equipment.
a. Brake horsepower
b. Drawbar horsepower
c. Power takeoff horsepower
d. All of the above
93. Variables affecting the drawbar horsepower::
a. Implement speed and width
b. Implement width and pulling force
c. Implement pulling force and speed
d. None of the above
94. PS is a German acronym for ________________ .
a. Pferdestark
b. Pferdstark
c. Pferdestarke
d. None of the above
95. cv is a French acronym for ____________ .
a. Cheval-vapeur
b. Chevapeur
c. Chevalvapour
d. None of the above
96. pk is Dutch acronym for ____________ .
a. Paardekracht
b. Pardkract
c. Padkracht
d. None of the above
97. 1 PS is equal to _________ watts
a. 735.49
b. 740.12
c. 760.00
d. None of the above
98. 1 pk is equal to ____________ watts
a. 735.49
b. 740.12
c. 760.00
d. None of the above
99. 1 cv is equal to _________ watts
a. 735.50
b. 740.12
c. 760.00
d. None of the above
100. A farm is planed be planted with corn at a spacing of 30 cm x 60 cm. As
engineer in-charge of the mechanization program of the farm which of the
following equipment would you recommend?
a. Drill
b. Row Crop Planter
c. Broadcaster
d. None of the above
101. Which of the following are the basic functions of a seeder and planter?
a. Open the seed furrow
b. Meter the seeds
c. Deposit the seeds
d. Cover the seeds
e. None of the above
f. All of the above
102. Instrument for measuring the speed of a shaft.
a. Odometer
b. Anemometer
c. Tachometer
d. All of the above
103. Instrument for measuring low-pressure head.
a. Dial type pressure gauge
b. Manometer
c. Orifice
d. None of the above
104. Instrument for measuring furnace temperature.
a. Glass bulb thermometer
b. Dial type bimetallic thermometer
c. Thermocouple wire thermometer
d. All of the above
105. It is a set of concave discs.
a. Gang
b. Disc set
c. Disc frame
d. None of the above

106. It is a set of sprinkler nozzles.

a. Boom
b. Sprinkler laterals
c. Sprayer nozzle set
d. None of the above
107. A central part of a plow where the share, moldboard, and landside are attached.
a. Frame
b. Frog
c. Shank
d. None of the above
108. It is an auxiliary plow-working element, mounted above the shin which deposits
the upper edge of the furrow in the furrow bottom.
a. Tail piece
b. Thrash board
c. Coulter
d. None of the above
109. The size of a moldboard plow is determined ________________ .
a. from the wing of the share to the landside
b. from tip of the moldboard to the landside
c. from the top of the moldboard to the point of the share
d. None of the above
110. It is a set of sprinkler nozzles.
a. Boom
b. Sprinkler laterals
c. Sprayer nozzle set
d. None of the above
111. A central part of a plow where the share, moldboard, and landside are attached.
a. Frame
b. Frog
c. Shank
d. None of the above
112. It is an auxiliary plow-working element, mounted above the shin which deposits
the upper edge of the furrow in the furrow bottom.
a. Tail piece
b. Thrash board
c. Coulter
d. None of the above
113. The size of a moldboard plow is determined ________________ .
a. from the wing of the share to the landside
b. from tip of the moldboard to the landside
c. from the top of the moldboard to the point of the share
d. None of the above
114. Component parts of a seeder that is used to calibrate the seed metering device.
a. Furrow wheel
b. Ground wheel
c. Support wheel
d. All of the above
115. A six-bottom moldboard plow is to be used to plow a heavy soil. How many
scrapers are there in the plow?
a. 2
b. 4
c. 6
d. None of the above
116. It is a part of the plow that connects the plow bottom and the frame.
a. Upper hitch point
b. Boom
c. Shank
d. None of the above
117. Material recommended by PAES for use as implement frame.
a. Mild steel
b. Cold rolled steel
c. Spring steel
d. None of the above
118. Material recommended by PAES in the manufacture of disk blade.
a. Mild steel
b. Carbon steel
c. Cast iron
d. None of the above
119. When a disk harrow consists of a front and rear gangs and is centrally positioned
with the tractor, it is classified as _________ ?
a. Single action harrow
b. Double action harrow
c. Offset harrow
d. None of the above
120. When a disk harrow consists of a front gangs only and is centrally positioned with
the tractor, it is classified as _________ ?
a. Single action harrow
b. Double action harrow
c. Offset harrow
d. None of the above
121. When a disk harrow consists of a front and/or rear gangs and is not centrally
positioned with the tractor, it is classified as _________ ?
a. Single action harrow
b. Double action harrow
c. Offset harrow
d. None of the above
122. It is the traverse distance between two adjacent discs.
a. Disk distance
b. Disk clearance
c. Disk spacing
d. None of the above
123. The angle between the axis of the set of disks and the line perpendicular to the
direction of the implement.
a. Disk angle
b. Gang angle
c. Implement angle
d. None of the above
124. It is a self-propelled machine having a single axle designed primarily to pull and
propel trailed or mounted agricultural implement and machinery.
a. Walking-type tractor
b. Pedestrian tractor
c. Hand tractor
d. None of the above
e. All of the above
125. Warranty period for hand tractor from the purchase of the machine.
a. 4 months
b. 6 months
c. 12 months
d. All of the above
126. Engine cooling method.
a. air cooled
b. water cooled
c. air and water cooled
d. None of the above
e. All of the above
127. Engine whose piston that requires two movements to complete one cycle.
a. Single-cycle
b. Two-cycle
c. Four-cycle
d. None of the above
128. An engine valve arrangement wherein the intake and exhaust valves are located in
the cylinder head.
a. I - head arrangement
b. L- head arrangement
c. X- head arrangement
d. None of the above
129. An engine valve arrangement wherein the intake and exhaust valves are located
on one side of the cylinder block.
a. I - head arrangement
b. L- head arrangement
c. X- head arrangement
d. None of the above
130. Percentage engine output to be attained when testing based on the maximum rated
power output.
a. 60%
b. 80%
c. 100%
d. All of the above
131. Basic hand tools for engine maintenance:
a. Open wrench
b. Adjustable wrench
c. Screw driver (Philip and Flat)
d. All of the above
e. None of the above
132. It is an articulated connection between a link and the implement.
a. Hitch point
b. Link point
c. Implement point
d. All of the above
e.
133. It is an articulated connection between a link and the tractor.
a. Hitch point
b. Link point
c. Implement point
d. All of the above
134. It is the center to center distance between two front or rear wheels.
a. Wheel clearance
b. Wheel tread
c. Wheel distance
d. None of the above
135. A type of four-wheel tractor where power is transmitted to all wheels of the
tractor.
a. Two-wheel drive tractor
b. Four-wheel drive tractor
c. Hydraulic drive tractor
d. None of the above
136. A type of four-wheel tractor where power is transmitted to rear wheels with small
front wheels being pushed along.
a. Two-wheel drive tractor
b. Four-wheel drive tractor
c. Hydraulic drive tractor
d. None of the above
137. Auxiliary gear shift lever of a tractor is usually located at the ____________.
a. right side of the operator seat
b. left side of the operator seat
c. front of the operator seat
d. None of the above

138. Hydraulic control level of a tractor are usually located at the ____________ .
a. right side of the operator seat
b. left side of the operator seat
c. front of the operator seat
d. None of the above
139. Drawbar types:
a. Fixed drawbar
b. Swinging drawbar
c. Link drawbar
d. All of the above
e. None of the above
140. PAES recommended thickness of drawbar for four-wheel agricultural tractor.
a. Not more than 32 mm
b. 32 mm
c. More than 32 mm
d. None of the above
141. PAES recommended diameter of hole in the drawbar for four-wheel agricultural
tractor.
a. 30 mm
b. 33 mm
c. 36 mm
d. None of the above
142. Front tread of four-wheel agricultural tractor is usually adjusted by ______ .
a. changing bolt position of the front axle
b. changing the size of wheel
c. changing the front axle
d. None of the above

143. The rear wheel for two-wheel and four wheel drive tractors are adjusted by
_____ .
a. inverting the wheel disc
b. changing the rear axle
c. changing the position of the bolt of the rear axle
d. None of the above
144. Types of brake system for agricultural tractors:
a. Internal expansion type
b. External expansion type
c. Disk type
d. All of the above
e. None of the above
145. Acceptable level wheel slip for two-wheel drive tractor on a firm soil.
a. 7 - 11%
b. 10 - 15%
c. 16 - 20%
d. None of the above

146. Acceptable level wheel slip for two-wheel drive tractor on a tilled or soft soil.
a. 7 - 11%
b. 10 - 15%
c. 16 - 20%
d. None of the above
147. Acceptable level wheel slip for four-wheel drive tractor on a firm soil.
a. 6 - 10%
b. 8 - 13%
c. 10 - 16%
d. None of the above
148. Acceptable level wheel slip for four-wheel drive tractor on a tilled or soft soil.
a. 6 - 10%
b. 8 - 13%
c. 10 - 16%
d. None of the above
149. It is a single or pair of wheels with radially mounted tilling blades attached to a
common shaft or axle of a puddling-type floating tiller.
a. Cage wheel
b. Tilling wheel
c. Hydro wheel
d. None of the above
150. Common designs of floatation structure for puddling-type floating tiller.
a. Elliptical-shaped
b. Boat type
c. Saucer type
d. Pontoon type
e. All of the above
f. None of the above
151. Another term for puddling-type floating tiller
a. Rotary tiller
b. Float-assist tiller
c. Garden tiller
d. None of the above
152. Manufacturer’ specification for float assisted tiller field capacity based on PAE
Standard.
a. 1.0 to 2.5 kph
b. 2.5 to 4.0 kph
c. 4.0 to 6.5 kph
d. None of the above
153. Recommended chain and sprocket drive for tractor powered by 3.73 to 5.22 kW
gasoline engine.
a. ANSI chain number 50
b. ANSI chain number 60
c. ANSI chain number 70
d. All of the above
e. None of the above
154. Recommended chain and sprocket drive for tractor powered by 5.22 kW and
above gasoline engine.
a. ANSI chain number 50
b. ANSI chain number 60
c. ANSI chain number 70
d. All of the above
e. None of the above
155. When heat alone is used to melt and flow metal together, the process is know as
_______.
a. Soldering
b. Pressure welding
c. Fusion Welding
d. None of the above
156. Welding by heating and then forcing the pieces together is called ______ .
a. Fusion welding
b. Pressure welding
c. Inertia Welding
d. All of the above
157. The most common form of gas welding uses the gases _______ .
a. Acetylene and air
b. Acetylene and hydrogen
c. Acetylene and oxygen
d. All of the above
158. Spot welding is a form of welding known as ________ .
a. Flow welding
b. Resistance welding
c. Forge welding
d. None of the above
159. The metal that is melted from a pieces being joined is called the _________ .
a. Filler metal
b. Weld metal
c. Base metal
d. None of the above
160. A form of resistance welding used for welding sheet metal is ________ .
a. Arc welding
b. Gas welding
c. Spot Welding
d. None of the above
161. The size of screw driver is measured by ___________ .
a. the length of the blade
b. its overall length
c. it diameter
d. None of the above
162. What type of fastener is used to fasten a metal part to wood?
a. Machine bolt
b. Lag screw
c. Carriage bolt
d. None of the above
163. What property of metal refers to its ability to resist penetration?
a. Hardness
b. Toughness
c. Strength
d. All of the above
164. Metals high in weldability are usually high in __________ .
a. Fusibility
b. Malleability
c. Ductility
d. All of the above
165. Ferrous metals are metals that contain __________ .
a. Copper
b. Aluminum
c. Iron
d. All of the above