Scribd Logo
Upload

Welcome to Scribd!

  • 111 views

    HP961 Controller Operating Instructions - Sep 2016

    Uploaded by

    Victor Gonzalez
    The document provides instructions for operating an HP961 controller. It describes how to zero the display, set the bottom bending roll position using limit switches, and program top and bottom soft limits. The soft limit programming mode allows setting the top soft limit J1 to a value like 50 and bottom J2 to 10. The bending roll can then be driven between those limits. Resetting to factory defaults sets J1 to 100,000 and J2 to 0.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    HP961 Controller Operating Instructions - Sep 2016

    Uploaded by

    Victor Gonzalez
    111 views2 pages
    The document provides instructions for operating an HP961 controller. It describes how to zero the display, set the bottom bending roll position using limit switches, and program top and bottom soft limits. The soft limit programming mode allows setting the top soft limit J1 to a value like 50 and bottom J2 to 10. The bending roll can then be driven between those limits. Resetting to factory defaults sets J1 to 100,000 and J2 to 0.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for operating an HP961 controller. It describes how to zero the display, set the bottom bending roll position using limit switches, and program top and bottom soft limits. The soft limit programming mode allows setting the top soft limit J1 to a value like 50 and bottom J2 to 10. The bending roll can then be driven between those limits. Resetting to factory defaults sets J1 to 100,000 and J2 to 0.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    111 views2 pages

    HP961 Controller Operating Instructions - Sep 2016

    Uploaded by

    Victor Gonzalez
    The document provides instructions for operating an HP961 controller. It describes how to zero the display, set the bottom bending roll position using limit switches, and program top and bottom soft limits. The soft limit programming mode allows setting the top soft limit J1 to a value like 50 and bottom J2 to 10. The bending roll can then be driven between those limits. Resetting to factory defaults sets J1 to 100,000 and J2 to 0.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    HP961 Controller Operating Instructions

    Sep-2016

    J1- Top soft limit J2- Bottom soft limit SET Arrow across Arrow up
    button button button

    Simple operation
     Zero display- Press arrow up button until display reads zero.
     Set bending roll bottom position- Press & hold arrow up button and press bending roll down
    button at the same time. Drive bending roll down until external limit switch stops travel. This
    is now the bottom position and bending roll can be driven full travel up/down.

    Soft limit setting & operation


    The controller can be programed to travel within a top and bottom soft limit and the operator can
    change soft limits to any desired size.

    J1= Top soft limit

    J2= Bottom soft limit

    End= Exit programing mode.

     PP0001= Soft limit programing mode

    Press set button and use the arrow across/up buttons to make display read PP0001. Press the
    SET button to enter soft limit programing mode.

    Menu diagram

    PP0001

    J1 J2 END

    1
    HP961 Controller Operating Instructions
    Sep-2016
    The below example outlines how to set the Top soft limit (J1) to position 50 & bottom soft limit (J2)
    position to 10. The final position set is dependent on user’s application.

     Set J1-Top soft limit

    Use arrow across button until J1 is displayed and press SET to enter limit. Make display read
    50 and press set to save and exit. This is now the top soft limit.

     Set J2- Bottom soft limit

    Use arrow across button until J2 is displayed and press SET to enter limit. Make display read
    10 and press SET to save and exit. This is now the bottom soft limit.

     Exit soft limit mode

    Use arrow across button until End is displayed and press SET to save and exit.

     Bending roll can now be drive up/down between 10 and 50.

    Reset factory settings - Set J1= 100000 & J2=0 and follow simple operation instructions.

    You might also like