01.

The flight crew use the ACP (audio control panel) to control Audio for communication
and navigation system, where come from the electrical source ACP obtained?
Select one:
a. 115 VAC from each transfer bus
b. 28 VDC from Bat bus
c. 16 VAC from REU

d. 15 VDC from REU

02. Where come from the audio alert signal which cannot turn off or cannot adjust
volume?
Select one:
a. Distance Measuring Equipment (DME)
b. Automatic direction finder (ADF)
c. Flight control computer (FCC)

d. VHF omnidirectional range (VOR) marker beacon

03. What Component to use to Modulated and demodulated radio frequency signal?
Select one:
a. Audio Control panel
b. Radio control panel
c. Transceiver

d. Transmitter
04. What the Voice Recorder continuosly records?
Select one:
a. Flight crew communications
b. Passenger compartment communications
c. Flight compartment sounds

d. Flight compartment sounds and flight crew communications, time

05. When the Voice Recorder operating?
Select one:
a. At least one engine running
b. Both engine running
c. Aircrfat in flight

d. Transfer bus 2 powered

06. Three Axis accelerometer measures acceleration along the vertical, lateral and
longitudinal axes up to ten times the normal operation range, what power source for
flight recorder Accelerometer?
Select one:
a. 115 VAC transfer bus 1
b. 115 VAC standby bus
c. 28 VDC FDAU

d. 28 VDC standby bus

07. The Aural Module has two channels, what happen if one channel failure?
Select one:
a. The audio output of aural warning module increase by 6db
b. The audio output of aural warning Module decrease by 6db
c. Wailer sound

d. Hi/Lo Chime sound

08. The FDAU has three failure indication, What is indication if FDAU does not send
data to the FDR?
Select one:
a. ACMS fail light come on
b. DFDR fail light come on
c. DFDAU failure light come on

d. Off light extinguish

09. The REU control All communication and have 3 station card and audio accessories
Unit, how to control station card ?
Select one:
a. Input from (audio control panel) ACP
b. Input from Microphone push-to-talk (PTT)
c. Input from (navigation control panel) NCP

d. Input from ACP and Mic PTT

10. When condition aural warning can give take off warning (intermittent Horn) when the
airplane in the air ?
Select one:
a. The ground spoiler interlock valve close
b. The leading edge flap are not up
c. The ground spoiler interlock valve is open and the leading edge flap are retracted

d. The Horizontal stabilizer is out of green band

11. What the sequence of sounds from most Important to least Important?
Select one:
a. The bell, Clacker, Chime
b. Intermittent horn, steady horn, wailer
c. The bell, chime, wailer

d. Steady horn, wailer, clacker

12. What signal to Aural warning to make continuous horn will sound?
Select one:
a. Discrete input from Cabin altitude panel for a cabin altitude warning
b. Discrete input from PSEU for landing warning
c. Discrete input from DFCS MCP For Auto pilot disconnect warning

d. Discrete input from ADIRU for an over speed

13. The source Excitation power for Roll sensor, pitch sensor and Auto pilot actuator is ?
Select one:
a. 115 V AC, 400 Hz
b. 28 V DC.
c. 26 V AC, 400 Hz

d. 14 V AC, 1800 Hz

14. The MCP (Mode control panel) has front panel and two channels that operate
independently. What happen when a failure on one channel ?
Select one:
a. The first officer course window is blank
b. The altitude display 50 000 feet
c. The IAS/Mach is blank

d. Alert tone come on

15. The Aural Warning Module gives the sound of a wailer for an autopilot disconnect
warning, what does to stop the wailer?
Select one:
a. Push the autopilot disconnect switch
b. Push the autopilot P/RST switch
c. Engage the Autopilot

d. All answer are true

16. When you push the master caution, these causes the circuits reset the master
caution annunciation and what the result happen?
Select one:
a. Master caution lights go off
b. System annunciator lights go off
c. Fault lights on the individual panel remain on if the panel still senses a fault

d. All answer are true

17. To change electrical signal command into hydraulically controlled mechanical input
perform by ?
Select one:
a. FCC
b. Autopilot actuator
c. LVDT

d. PCU
18. What the warning give the aural warning module sound continuous Horn sound?
Select one:
a. Takeoff warning
b. Landing warning
c. Cabin Altitude warning

d. Over speed warning

19. What the function of the master dim and test switch?
Select one:
a. Test the indicator only
b. Cause the indicator bright
c. Test lighting

d. Test the indicator, test panel and cause the indicator and panel lights to come on in
the bright or dim
20. Aircraft flap not up and true airspeed is 10 knots above the target speed and not
accelerating to target speed, what indication will be come on?
Select one:
a. The amber A/P flashes
b. The amber A/T flashes
c. The amber FMC flashes

d. The Red A/T steady

21. The A/T function in FCC A, what condition A/T disengages with No flashes come
on ?
Select one:
a. Not valid sensor and A/T system condition
b. Airplane on ground after the flight is complete
c. 10 degrees diff between two T/L.
d. Disengage signal from disengage switch.
22. Where you find indication of airspeed warning?
Select one:
a. ASA (Auto flight Status annunciator)
b. MCP (Mode Control panel)
c. P5 Panel (Flight Control)

d. MCDU
23. Which of the following below is Not a major component of the Inertial Reference
System?
Select one:
a. Air Data Inertia Reference Unit (ADIRU)
b. Inertia System Display Unit (ISDU)
c. Instrument display unit

d. Mode Selector Unit (MSU)

24. Where you find indication operational and Failure Of ADIRS?
Select one:
a. CDU
b. IRS master Caution Unit
c. ISDU ( Inertial System Display Unit)

d. MSU (Mode select Unit)

25. With the External power applied, the Dim incandescent entry light is come On, where
location entry light and what power source entry light?
Select one:
a. Fwd entry light and 28 V DC hot batt bus
b. Aft entry light and 115 V AC
c. Fwd entry light and 115 V AC

d. Aft entry light and 28 V DC hot batt bus

26. The Inertial Reference function of the ADIRU supplies Heading and Attitude
information, How ADIRU calculate this information?
Select one:
a. With GPS and MMR
b. With Accelerometers and Laser gyros
c. With Accelerometer

d. With Compas and Processor

27. In Navigation Mode what data to use to calculate Attitude, heading, velocity and
distance flown?
Select one:
a. Initial Starting point
b. Gyro value
c. Accelerometer value

d. All answer are true

28. What function of the IR data (pitch, roll, Vertical speed, Acceleration) send to ADR
Processor?
Select one:
a. Calculate thrust and ground effect compensation Value
b. BITE test
c. Baro correction

d. Cross talk
29. The TAT value that show is from the left ADIRU, where indication of Total air
Temperature?
Select one:
a. P5 panel
b. Top of PFD
c. Top of Engine display

d. Top of Navigation Display

30. How the radio Altimeter (RA) system measures the Vertical distance?
Select one:
a. Computed Receive RF signal from ground Transmitter
b. Computed with receiver transmitter unit by comparing the transmitted signal to the
received signal
c. Computed Receive signal from ADIRU

d. Computed received signal from FCC

31. When Ground crew call horn will energized and activated ?
Select one:
a. ADIRU alignment complete.
b. Equipment cooling select altenate
c. ADIRU on DC and ADIRU cooling air fan fail

d. No enter position

32. When the PWS Automatically Activates for takeoff condition?
Select one:
a. The airplane is in the air above 2300 feet AGL
b. WXR is not manually selected on EFIS control panel
c. WXR is manually turned on Via EFIS control panel and the selected WXR mode is
Test

d. The airplane is on ground and either one or both of TRA exceed 53 degrees
33. The navigation control panel (NCP) has frequency transfer switch to move selected
ILS frequency from standby display window to Active window, what happen if the
autopilot engaged in the APP mode you push transfer switch?
Select one:
a. AP will disengages
b. FCC causes a reset mode
c. AP stay engage

d. AP will change from CMD to CWS

34. The Mode Control panel (MCP) is primary interface between crew and FCC, What
other input Crew to FCC?
Select one:
a. Autopilot (A/P) disengage switch
b. Control wheel steering (CWS)
c. Autopilot (A/P) disengage switch and Control wheel steering (CWS) force transducer

d. Yaw damper switch

35. What component give an interface between the DFCS and airplane system?
Select one:
a. EFIS Control Panel
b. IFSAU
c. DEU

d. MCP
36. Two Purpose Mach trim Actuator is to trim elevator at high speed to raise the nose to
correct for Mach tuck and to move the elevator when the airplane is in the FCC
controlled neutral shift region. What mean FCNSE?
Select one:
a. Flap are not up position and either engine N1 is more than 20 %
b. Flap are up and either engine running
c. Flap are not up position and Both engine running

d. Flap are up and inflight

37. The DFCS supplies an Altitudes windows warning when altitude in FCC memory
change with no change of the altitude selector, what indication Altitude warning?
Select one:
a. Altitude display current altitude
b. Altitude display goes to 50.000 Feet
c. No aural warning

d. Red Border around the airplane altitude display steady

38. The FMC will calculate thrust N1 Limits and N1 target for each phase and send DEU,
what data received EEC?
Select one:
a. N1 Limit
b. N1 target which calculate equivalent TRA target send to A/T
c. N2 Limit

d. N2 Target which calculate equivalent TRA target

39. What mode Auto throttle at flight mode annunciation when A/T Removes power from
the ASMs
Select one:
a. THR HLD
b. ARM
c. FMC SPD

d. MCP SPD
40. The A/T warning flasher latches on when the A/T disconnect, what does reset A/T
warning?
Select one:
a. Engaged The A/T
b. Push a disengage switch
c. Push an A/T warning light

d. All answer are True