PK605DM

Two-Part Thermal Conductive Gap Filler

FEATURES
/ Thermal conductivity: 5.0 W/m*K
/ Fast curing in normal atmospheric temperature
/ Great reliability
/ Great sealing in low pressure

TYPICAL APPLICATIONS
/ Between CPU and heat sink
/ Between a component and heat sink
/ Power supplies
/ High speed mass storage drives
/ Telecommunication hardware
/ Electric vehicle& Automotive battery

CONFIGURATIONS
/ Cartridges: 50ml, 400ml
/ Other special and custom sizes are available upon request

DISPENSING INSTRUCTIONS
Use the disposable plastic static mixing nozzles to mix parts A and B together to the desired ratio.
Liquid gap fillers can be dispensed using an automatic dispensing machine or a manual dispensing
tool that can be provided by LiPOLY upon request/purchase. The disposable plastic static mixing
nozzles cannot be re-used.

STORAGE
Two-part liquid gap fillers should be stored in climate-controlled environments at or below 25°C.
Keep liquid gap fillers away from direct sunlight and away from high-temperature environments.

PRESERVATION

PRECAUTIONS
The two-part liquid gap filler may not cure properly if it comes into contact with certain substances,
including amine, sulfur, organophosphorus compounds, and organotin compounds. Please avoid the
following substances when handling: (N, P, S, Sn, Pb, Hg, Sb, Bi, As) Ensure a clean mixing container
is used (e.g.: paper cup or plastic cup) before injecting the A and B parts into the mixing container.
The plasticizer, wax from the cups, varnish or the epoxy from the oven may contaminate the A and B
parts. You are reminded to pre-test the gap filler before using it.
 PLEASE NOTE
It’s recommended that the diameter of mixing tube outlet should be 3mm at least, which can solve the
possible problem of poor fluidity caused by ambient temperature.

TYPICAL PROPERTIES
PROPERTY PK605DM TEST METHOD UNIT

Red (A part)
Color White (B part) Visual -

100%
Solid content - -
(Two-part : 100:100)

Viscosity A 110 ISO 3219 Pa.s

Viscosity B 80 ISO 3219 Pa.s

Density 3.3 ASTM D792 g/cm³

Shelf life 24 months - -

ROHS & REACH Compliant - -

SOLID(AFTER CURE)

Thermal conductivity 5.0 ASTM D5470 W/m*K

Thermal impedance@10mils BLT 0.092 ASTM D5470 °C-in²/ W

Thermal impedance@20mils BLT 0.171 ASTM D5470 °C-in²/ W

Thermal impedance@30mils BLT 0.254 ASTM D5470 °C-in²/ W

Hardness 85 ASTM D2240 Shore OO

Working temp (long term) -60 ~ 200 - °C

Operating ambient temp 20 ~ 30 - °C

ELECTRICAL

Dielectric breakdown 8 ASTM D149 KV/mm

Surface resistivity >10¹¹ ASTM D257 Ohm

Volume resistivity >10 ASTM D257 Ohm-m

CURE SCHEDULE

Pot life @ 25°C 10~15 By LiPOLY min

Surface dry @ 25°C 20~25 By LiPOLY min

Cure @ 25°C 25~30 By LiPOLY min

Cure @ 100°C 40 By LiPOLY sec

Cure @ 120°C 10 By LiPOLY sec

Note: All specifications provided by LiPOLY are subject to change without notice. The test methods used by LiPOLY are based on the TIM Tester method and ASTM D5470 test method. These test methods are used
as the definition standards for LiPOLY. Property values provided in this document are not for product specifications or guaranteed. This document does not guarantee the performance and quality required for the
purchaser’s specific purpose. The purchaser needs to evaluate and verify the safety before using the material. We strongly recommend the purchaser pre-test the product and verify the performance of the product
under the purchaser’s specific conditions. Liability and use of the product are the responsibility of the end user. LiPOLY makes no warranty as to the suitability, merchantability, or non-infringement of any LiPOLY
material or product for any specific or general uses. LiPOLY shall not be liable for incidental orconsequential damages of any kind. All LiPOLY products are sold in accordance with the LiPOLY Terms and Conditions in
effect at the time of purchase and a copy of which will be furnished upon request. All rights reserved, including LiPOLY trademarks or registered trademarks of LiPOLY or its affiliates. Statements concerning possible
or suggested uses made herein shall not be relied upon or be constructed as a guaranty of patent infringement. Copyright 2022 LiPOLY.