Quick User Guide Output accuracy ±0.

25% of FS Before start-up it is particularly important to ensure: FRONT PANEL DESCRIPTION

UT-94 • Terminal wiring: check that all cables are correctly
Relays Output connected according to the connection diagram Symbol Function
Relays 2 Nos. • All wiring must confirm to appropriate standards of good
practice and local codes and regulations. Wiring must be This key is used to start menu, scroll through
Type Single Change over (C, NO, NC)
suitable for voltage, current and temperature rating of the the menu and save values.
Rating 2A @ 230VAC / 30VDC system.
• Unused control terminals should not be used as jumper This key is used to select the menu options,
Loop Power Supply points as they may be internally connected, which may for shifting the digit of the selected parameters
Supply Voltage 24VDC (±10%) @30mA cause damage to the unit. and for ambient display in Run Mode for TC
Input.
Communication Details DIMENSIONS DETAILS
This key is used to revert back to the parent
Communication 55 mm menu from the sub menu levels and Increment
Universal Transmitter Interface RS485 (2 Wire) the selected digit. This key is also used as
Protocol Modbus-RTU Acknowledgement key for Alarm/trip type
SPECIFICATIONS Baud rate 4800,9600, 19200 bps relay.
4 digit 0.3 inch RED Display.
Input type Range Input type Range
Physical Display process value. Display parameter
E -200 to 1000ºC mV(-10-500) PV
Dimension (H x W x D) mm 75 x 55 x 110 name when user set parameter. Display error
J -200 to 1200ºC Pot(0-2000Ω) Front Bezel (H x W)mm 75 x 55 message when an error occurs.
K -200 to 1370ºC 0-2 V Weight Approx. <250g
ON when Relay-1 is energized & OFF
T -200 to 400ºC 0.4-2 V Enclosure Material ABS RL1
otherwise.
Enclosure Protection IP 20
B 450 to 1820ºC *0-20 mA -1999 to 9999
Terminal Cable Size 2.5mm2 ON when Relay-2 is energized & OFF
R 0 to 1750ºC *4 – 20mA RL2
otherwise.
S 0 to 1750°C 0-5 V Environmental Conditions TERMINAL CONNECTION
Tx ON when device is transmitting Data (RS-485).
N -200 to 1300 oC 1-5 V TEMPCO
Pt 100 -199.9 to 850 OC 0-10 V Input to PV Display < 100ppm/oC Rx ON when device is receiving Data (RS-485).
*Use external 100ohms, 0.1% for current Input Display to RX < 150ppm/oC
Table 1.1 Humidity 20% to 95% RH PARAMETER SETTING
Inputs
(Non-Condensing)
Accuracy Following parameters can view or change during run time.
Ambient temperature 0 to 55°C
T/C- E, J, K, T, N, + 0.1% of Full Span ± 1 count
Storage Temperature 0 to 80°C • For Thermocouple input type, Press key to show
RTD & Linear ambient temperature
T/C-B, R, S + 0.25% of Full Span ± 1 count
Power Supply • Press key will ask to enter password, Change
Resolution ADC: 17 bits,Display :0.1°C/1Count Standard 85-265VAC/ 100-300VDC
Sampling Time <75ms Optional 18-36VDC password using Key then press key, On entering
CJC Error ±2.0 °C Max Power consumption <10 VA correct password, unit will show parameters.
Sensor Burnout
0.5uA • Following parameters can be viewed using Key. Its
current Isolation (Withstanding voltage)
RTD excitation value can be viewed using key and it can be changed
1mA (Approx.) • Between primary terminals* and secondary terminals**:
current At least 1500 V AC for 1 minute using Keys.
Response time < 200ms • Between primary terminals* and grounding terminal:
NMRR > 50 dB At least 1500 V AC for 1 minute Default
Display Name Description
CMRR >120 dB • Between grounding terminal and secondary terminals**: Value
LOAD CONNECTION
>1MΩ for Voltage, At least 1500 V AC for 1 minute PROG Program
Input Impedance - -
100Ω for Current • Between secondary terminals**: PRoG
PRoG)
(PRo Mode
Max Voltage 20VDC At least 500 V AC for 1 minute ST-1 Set point value for
Set Point-1 0100
* Primary terminals indicate power terminals and relay ST-
ST-1)
(ST relay-1
Display & Keys
output terminals. HY-1 Hysteresis- Hysteresis Value for
PV Display 4-Digit, 7-Segment, 0.3” High, Red 0005
** Secondary terminals indicate analog I/O signal and HY-
HY-1)
(HY 1 Relay-1. 0 to 100
Status Individual RED Led for Power, Relay & Communication O/P.
Indication Communication Status ST-2 Set point value for
Insulation resistance: 2000MΩ or more at 500 V DC Set Point-2 0200
ST-
ST-2)
(ST relay-2
Keys Enter/Scroll, Select/Shift, Escape/ACK/INC between power terminals and grounding terminal.
HY-2 Hysteresis- Hysteresis Value for
0005
Output Types HY-
HY-2)
(HY 2 Relay-2. 0 to 100
SAFETY/WARNING PRECAUSTIONS
Retransmission Output CONF Configurat-
Output Signal - -
To ensure that the device can be operated safely and all Electrical precautions during use Conf
Conf)
(Con ion Mode
DC Current 4-20mA/ 0-20mA functions can be used, please read these instructions Electrical noise generated by switching of inductive loads Select i/p parameter
DC Voltage 0 to 10 V, 0 to 5V, 1 to 5V carefully. INP
can create momentary disruption, erratic display, latch up, Input iPTY/ZEro
PTY ZEro/SPAn
ZEro SPAn/DP
SPAn DP/
DP -
Load resistance Installation and Start-up must be carried out by qualified inP
inP)
(in
data loss or permanent damage to the instrument. Use of vniT
vniT/inLo
inLo/inHi
inLo inHi
For Current o/p <750Ω personnel only. snubber circuits across loads as shown above, is IPTY Set PV input type
The relevant county-specific regulations must also be Input Type 0-5w
For Voltage o/p >4KΩ recommended. ipty
(ipty) tC e/tC
e tC j/tC
j tC K/
K tC
observed.
Doc.Ref. No. m98A/QG/101 Issue No.:01 Page 1 of 2
 t/tC
tC b/tC
b tC r/
r tC s/ s RLno)
(RLno
RLno 0001
0001/000
0002
0002 Relay Logic
tC n/pt100
n pt100/mv
pt100 mv/pot
mv pot Set Relay o/p state Without acknowledge key pressed
0.4
0.4-2V/0
/0. 2V 0-20 /4 4-20/
20 OPSE Open when i/p open ACK IN ACK IN
vPSC ALARM
0-5v /1 1-5w / 0-10 oPSE)
(oPSE Sensor condition CONDITION RELAY/LED NORMAL ABNORMAL UP DOWN ABNORMAL NORMAL NORMAL
Can be set to any vPSC/Dn
SC DnSC
DnSC LATCH/TRIP
CONDITION CONDITION
ZERO value within the Input Relay ALARM LED LED OFF FLASH FLASH OFF - STEADY OFF
Zero -1999 LOGC Set Relay Operation
zero)
(zero
zero Range & less the SPAN Control Hi LATCH YES RELAY OFF ON ON OFF - OFF OFF
Value. LoGC
LoGC)
(LoGC Hi/low
Hi low
Logic ALARM LED LED OFF FLASH FLASH OFF - OFF OFF
Can be set to any High
C AL Configurati Set Alarm Logic LATCH NO RELAY OFF ON ON OFF - OFF OFF
SPAN value within the Input ALRM
Span 9999 C AL)
(C AL on Alarm ALRM
ALRM/TRi
RM TRiP
TRiP/ooPEn
PEn LED OFF FLASH OFF OFF - STEADY OFF
span)
(span
span Range & greater the TRIP
Set Latch Status only if RELAY OFF ON OFF OFF - ON OFF
ZERO Value. LTCH Alarm type relay is ALARM LED LED OFF FLASH OFF FLASH - STEADY OFF
Set position of Decimal Latch YES
LTCH)
(LTCH
LTCH selected. LATCH YES RELAY OFF ON OFF ON - OFF OFF
DP Decimal Point on Display for YES/no
YES no ALARM LED LED OFF FLASH OFF FLASH - OFF OFF
0000 LOW
dp)
(dp
dp Point Linear inputs Select Communication LATCH NO RELAY OFF ON OFF ON - OFF OFF
0000 to 0003 COM Communic-
Parameter - LED OFF FLASH OFF OFF - STEADY OFF
Set Engineering unit CoM
CoM)
(Co ation Menu TRIP
UNIT Engineerin SR-
SR-no/BAv
BAvD
BAvD RELAY OFF ON OFF OFF - ON OFF
for TC and RTD inputs DEG.C Unit ID for
vnit)
(vnit g Units SRNO With acknowledge key pressed
DEG.C/DEG.F
DEG.C DEG.F/DEG.K
DEG.F DEG.K Serial No Communication 0001
SRno)
(SRno
SRno ACK IN ACK IN
Can be set to any 0 1 to 247 ALARM
CONDITION RELAY/LED NORMAL ABNORMAL UP DOWN ABNORMAL NORMAL NORMAL
*INLO value within the Input (POT) LATCH/TRIP
Input Low BAUD Set Baud Rate CONDITION CONDITION
inlo)
(inlo
inlo Range & less the SPAN -10 Baud Rate 4800
BAvD
BAvD)
(BAv 4800/9600
4800 9600/19200
9600 19200 ALARM LED LED OFF FLASH FLASH OFF STEADY STEADY OFF
Value. (mV)
ADV Advance LATCH YES RELAY OFF ON ON OFF OFF OFF OFF
Can be set to any 2000 - -
ADw)
(ADw
ADw Parameter ALARM LED LED OFF FLASH FLASH OFF STEADY OFF OFF
*INHI value within the Input (POT) High
Input High FILT Digital Digital Filtering LATCH NO RELAY OFF ON ON OFF OFF OFF OFF
inhi)
(inhi
inhi Range & greater the -500 000.0
FiLT
FiLT)
(FiLT Filter 000.0 – 060.0 Sec LED OFF FLASH OFF OFF STEADY STEADY OFF
ZERO Value. (mV) TRIP
FSET Factory Give Default password RELAY OFF ON OFF OFF ON ON OFF
OUT Select o/p Parameter 0000
Output FSET)
(FSET
FSET Setting for factory settings ALARM LED LED OFF FLASH OFF FLASH STEADY STEADY OFF
ovT
ovT)
(ov RTR/RELY
RTR RELY/Co
RELY CoM
CoM
PASS Change Password LATCH YES RELAY OFF ON OFF ON OFF OFF OFF
Retransmission menu Password 0000
PASS)
(PASS
PASS -1999 to 9999 ALARM LED LED OFF FLASH OFF FLASH STEADY OFF OFF
RTR Retransmi- oPno/o
oPno oPTY/op
PTY op Z/ Low
- Output will be come as LATCH NO RELAY OFF ON OFF ON OFF OFF OFF
RTR)
(RTR
RTR ssion oP S/oPLo
oPLo/oPHi
oPLo oPHi/
oPHi
per PV = SQRT[{ LED OFF FLASH OFF OFF STEADY STEADY OFF
oPSC/Di
PSC DiR
DiR TRIP
(input reading – RELAY OFF ON OFF OFF ON ON OFF
OPNO Output Set o/p Channel
0001 config. IP Zero) / Note: If open type relay is selected then relay and LED will be ON when OPEN condition, while it will remain off if not in
opno)
(opno
opno Channel No 0001
0001/000
0002
0002 SQRT Square
(config. IP Span – no OPEN condition.
Set Voltage/Current SQRT)
(SQRT
SQRT root
Config. IP Zero)} *
OPTY Output o/p Config. OP Span] +
0-5w ORDERING CODE
oPTY)
(oPTY Type 4–20
20/0
20 0-5w
5w/1
5w 1-5w5w/
5w Config. OP Zero 1.
0-10
10/
10 0–2020 YES/no
YES no No of Communica-
% of Output for scaling Time Setting for Come Model Input Type APS O/P type-1 O/P type-1 Relay O/P
Output (O/P Zero limit will be O/P tion
OP Z TOUT back to RUN mode on
Zero for limited to this 000.0 Time Out 0060 UT-94 X XX X X X X X
oP Z)
(o Z TovT
TovT)
(Tov no key operation
Scaling configured 0-30 % of 10-300 SEC 1 E 85-265VAC/ 1 4-20mA None N None N NONE
O/P Span) U1 1 One 0
CALI Calibration 100-300VDC
% of output for scaling - - 2 J 2 0-20mA 1 4-20mA Y Yes Y RS485
CALi)
(CALi
CALi Mode
Output (O/P Span limit will be 3 K U2 18-36VDC 2 Two 3 1-5VDC 2 0-20mA
OP S **AMB
Span for limited to this 100.0 Ambient Ambient Adjustment - 4 T 4 0-5VDC 3 1-5VDC
oP S)
(o S AMB)
(AMB
AMB
Scaling configured 70-100 % 5 B 5 0-10VDC 4 0-5VDC
INP Select Input parameter
of O/P Span) - 6 R S Special 5 0-10VDC
inP
inP)
(in ZERo/SPAn
ZERo SPAn
% of Output (O/P Low 7 S S Special
ZERO Calibration Calibration Zero for PV
OPLO limit will be limited to - 8 N
Output Low 000.0 ZERo)
(ZERo
ZERo Zero Input
oPLo)
(oPLo
oPLo this configured 0-25 % 9 Pt-100
SPAN Calibration Calibration Span for PV
of O/P Span) - C 4-20mA
SPAn)
(SPAn
SPAn Span Input
% of output (O/P Hi D 0-20mA
OUT Select output
OPHI Output limit will be limited to E 1-5VDC
100.0 ovT
ovT)
(ov parameter -
oPHi)
(oPHi
oPHi High this configured 75-100 F 0-5VDC
OPno/ZERo
OPno ZERo/SPAn
ZERo SPAn
% of O/P Span) G 0-10VDC For operation manual please visit www.masibus.com
OPNO Select Output No.
Set Rx state when i/p Output No. 1 W 0.4-2VDC Specifications are subject to change without notice due to
OPSC Open oPno)
(oPno
oPno 0001/0002
0001 0002
open condition vpSC X -10-500mV continuous improvements.
oPSC)
(o SC Sensor ZERO Calibration Calibration Zero for PV Masibus Automation And Instrumentation Pvt. Ltd.
vPSC/Dn
PSC DnSC
DnSC - Y 0-2 VDC
ZERo)
(ZERo
ZERo Zero Input B-30, GIDC Electronics Estate, Sector-25, Gandhinagar-
Retransmis Set Direction For the Pot
DIR SPAN Calibration Calibration Span for PV Z (0-2000 382044, Gujarat, India.
sion Retransmission o/p DiRT -
DiR
DiR)
(Di SPAn)
(SPAn
SPAn Span Input ohms) Tel:+91 79 23287275-79 Fax: +91 79 23287281
Direction DiR
DiRt/REREwr
REwr
VER S Special Web:www.masibus.com Email:[email protected]
Relay Parameter Version - 9.00
RELY wER)
(wER
wER
Relay RLno/o
RLno oPSE/Lo
PSE LoGC
LoGC/
GC -
RELY)
(RELY
RELY
C AL/LTCH
AL LTCH *Parameter is only shows if input type is mV or POT
RLNO Relay No. Select Relay 0000 **Parameter is only shows if input type is TC
Doc.Ref. No. m98A/QG/101 Issue No.:01 Page 2 of 2