Tools Get Ready Soldering Skills and Requirements

DSO 068 Oscilloscope DIY Kit

1 Iron (20W) 4 Screw driver 1 Check part values & quantities against part list 1 Put leads through mounting from installation side of
Assembly Guide ( PCB Version: H )
2 Solder wire 5 Flush cutter 2 Meter and identify resistor values by ohm meter
PCB. Ensue they evenly touch PCB (picture below).
Rev. 03 2 Solder at the other side of PCB. Solder should fully
3 Multimeter 6 Tweezers 3 Understand all part polarities and orientations
Step 1 Assembly the Main Board fill and cover soldering pads.
Avoid bridges with
1. Complete the steps in "Get Ready" and understand soldering requirements. neighbering pads.
Identify + 3 Cut unused leads
2. Install parts by the order of part list. Start from the back side of main board.
3. Pay special attention to part polarity at soldering. Refer to photos to the right. Polarity & - E flush with cutter.
4. For BOB boards and LCD soldering refer to photos at bottom for details. Orientation + - + - B
C
5. Perform power-up tests as suggested in the part list. Diode LED Electrolytic cap. Transistor Note: Please install by the order given in the Part List below.
TIP: Resistor values are easily mis-read. TIP: C3 and R32
Meter checking is strongly suggested. are not required. Part List
USB-Uart Conv. Catagory Seq. Type/Spec Qty Designator/Location
Buzzer Neg. P.S. Main PCB 1 PCB#: 109-06800-00H 1
Volt. Step-up Conv. Conv. JYE116（ BOB4） JYE117（BOB3） JYE118（BOB2） JYE119 （ BOB1） JYE120（BOB5） Resistor 2 510KΩ ，5%， 1/8W 2 R1, R27
Reset （Pin 1 indicated by arrow） 3 200KΩ ，1%， 1/8W 1 R3
USB Socket LED Inductor 4 2MΩ ，1% ，1/8W 2 R2, R4
LCD Module Rotary Encoder 5 20KΩ ，1% ，1/8W 1 R5
Batt. Charger Diode Electrolytic Cap. 6 300Ω ，1% ，1/8W 1 R6
7 180Ω ，1% ，1/8W 1 R7
Power Switch Resistor 8 120Ω, 1%, 1/8W 3 R8, R12, R21
Test
9 3.3KΩ ，1%，1/8W 2 R10, R22
Signal
10 470Ω ，1% ，1/8W 3 R11, R31, R 33
Output 11 10KΩ ，1 %，1/8W 3 R9, R20,R30
12 1KΩ ，5% ，1/8W 5 R24,R25,R26,R28,R29
13 10MΩ, 5 %, 1/8W 1 R40
Jumper 14 Short with solder 1 JP9
Ceramic Cap. Diode 15 1N4148，DO-35 2 D2,D3
External Inductor 16 100uH, φ2.5 X 6mm 3 L1,L4,L5
P.S. Conn. Battery Cap. Trimmer Crystal 17 20MHz， φ2 X 6mm 1 Y1
Conn. Keypad Crystal Connector 18 USB socket, MiNi- B type 1 J1
MCU Switch 19 Tact, 6 X 6 X 5mm 1 SW12
Main A/D Converter
LCD Capacitor 20 300pF, ceramic disk 2 C2,C23
Contrast MCU Transistor 21 3pF, ceramic disk 1 C4
Back Side Adj. Extention 22 1pF, ceramic disk 1 C6
Ports CBB Cap Slide Switch 23 120pF, ceramic disk 3 C7, C13, C32
24 0.1uF, ceramic disk 12 C9,C10,C11,C12,C14,
C15,C16,C18,C20,C24,
TIP: Do not install J4 if battery is to be mounted on back cover.Insert Front Side C25,C26
the pins into programmer header to perform U4 and U5 programming.
25 15pF, ceramic disk 2 C21,C22
26 0.1uF/100V, CBB 1 C1
Buzzer 27 5V, passive, φ9 X 5.5mm 1 BP1
Important! Unused leads under LCD must be cut flush to avoid short to LCD module! Diode 28 LED, φ3mm , red 1 D1
BOB Boards Orientation LCD Installation Connector 29 2pins, 2.54mm 1 J6
Transistor 30 8550, TO-92 ( E-B-C) 2 Q1, Q2
Pin 1 (square pad) indicated ASSY2 ASSY 3 L abels Electro. 31 10uF,16V, φ4 X 5mm 1 C19
by arrow Capacitor 32 100uF,16V, φ6X 7mm 5 C17,C27,C28,C29,C30
Cut leads sh ort Connector 33 DC005, φ2.1 mm core 1 J2
under LCD
BOB 34 JYE116, step-up convertor 1 BOB4
Board 35 JYE120, neg. P.S. convertor 1 BOB5
36 JYE117, On/Off switch 1 BOB3（ optional）
ASSY1 37 JYE118, battery charger 1 BOB2（ optional）
A. B. C. D. 38 JYE119,UART-USB conv. 1 BOB1（ optional）
Lay PCB flat. Insert mount- Identify the holes with labels Put LCD onto strips as shown. Turn LCD and main board over. Perform power-up test 1 as described on the reverse page.
ing strips with longer pins on LCD. They should go Solder pins at corners first. Do Complete soldering following Continue following assembly after the test.
into holes. with the long strip. the rest after flatness ensured. same procedures as in C. LCD 39 128X64 graphic, 12864-16 1 LCD1
Pin 40 SIP, 2mm, 20X1 1
BOBs and Jumpers
BOB Board Installation Strip 41 SIP, 2mm, 2X1 2
Switch 42 Slide switch，SS-23D06 3 SW1,SW2,SW3
Keep JP1 open if BOB2 Switch 43 Rotary Enc., EC11, 10mm 1 SW4
is installed. Otherwise Pin strip 44 DIP，2.54mm，5X2 2 J4,J5（Do not install）
close it. Enclosure 45 Top(1), bottom(1), stand(1) 1 set
Perform power-up
Keep JP2 open if BOB3 switch caps(3), dial cap(1)
is installed. Otherwise Switch 46 7-key silicone button pad 1 test 2 as described on
close it. Connector 47 BNC，BNC-KY 2 the reverse page after
A. Use the small acrylic B. Apply solder to one C. Apply solder to the D. Put BOB to place E. Maintain BOB upright F. Finish the rest pins. Wire 48 2-core header/wire, 10cm 1 all components have
More at the reverse page tool provided. pin. corresponding pin on and align pads. and fix it by melting Screw 49 2.3*8mm, self tapping 4 been installed on
main PCB. the solder. Wire 50 Shielding wire, 8cm 1 board.
JYE Tech Ltd. - www.jyetech.com -
 Adjust Compensation Install Batter &
Step 2 Power Up Tests Step 3 Capacitors Step 4 Enclosure Tech Support: www.jyetech.com/forum
Powering-up Test 1 Compensation capacitors can be
adjusted using the built-in signal
Double check to ensure no missed or cold solder or shorts generator. Follow steps below: 2
Make sure BOB4 and BOB5 have been installed 1
Close JP2 for the time being (even BOB3 is installed) 1. Connect test signal output to scope input
Keep JP3、JP4 open (see photo below) and set SW1 to DC.
Not enough 2. Power up. Set test signal to 10KHz and

通电检查
USB powered Battery powered 5V. Set scope timebase to 20us.
Keep JP1 open
3. Set SW & SW3 to 1V & X2 respectively. A. Install BNC connectors B. Cap slide switches. Insert C. Hold board tight towards D. Connect input signal BNC
Close JP1 if no BOB2 Adjust trigger level to make display
Make sure BOB2 in
and place silicone pad. board to connector holes. USB end and push in. to main board as shown.
stable if necessary. Change C8 to obtain
waveform as the middle of photos left.
4. Keep signal frequence unchanged and
Power up. Check voltage No Follow "No Power" Good set amplitude to 1V. Set SW2 & SW3 to

通电检查
Central
at +5V test point. Is it +5V? flow chart to check 0.1V and X5 respectively. Make display conductor

Yes stable. Change C5 to obtain waveform Tight

Outter Tight
Power off. Close JP4 Screw
as the middle of photos left. conductor Screw

5. Remove connection between test signal

Power up and check +5V No Check for soldering mistakes. output and scope input. Adjustment is
again. Is it still +5V? Wrong polarity, shorts, etc.
done.
E. Connect test signal with F. Tight two screws and attach G. Put on back cover. Tight H. Put dial cap on and you
Yes shielding wire provided batt. to center of back cover the two screws as shown. are done.
Too much
通电检查
Press SW12. Do you see LED No LED reversed ?
blink once (if bootloader U4 pin 20 voltage low ? Major Jumpers Explained Quick Waveform Diaplay Test Power Supply Options
installed) and then twice ? Check Y1、C21、C22
JP1：This is by-pass of charger BOB2. If battery Source BOB2 JP1 Remarks
Yes is not used (i.e. no BOB2) keep JP1 closed.
Continue to install TIP: Close JP7 to enable
Scope input JP2：This is by-pass of switch BOB3. If BOB3 Yes Open
USB
parts on the front buzzer. It beeps as LED blinks is not used JP2 should be closed. In order to focus No Close
on the main circuit JP2 can be temporarily closed
at power-up test even BOB3 is installed. Keep it Int. Batt. Yes Open
open after the test. Ext. Batt.
Note: JP9 must be closed C5 Test JP3：This is by-pass of step-up converter BOB4. (J2) Yes Open Close JP5
Powering-up Test 2
before power-up test 2 signal Usually JP3 should be kept open. Ext. 5V Yes Open Install D5 (D5
No Follow "LCD Dark"
C8 output JP4：This is the connecting point of power supply (J2) No Close is not provided)
LCD backlight on ？ to the rest circuits. For safety JP4 should only be
flowchart to check closed after power supply is tested good. Touch probe tip with a finger to Note: Do not simultaneously connect
Yes Temporarily connect test signal output to
show introduced main line signal external and internal batteries.
Adjust contrast. Can you No Follow "No display" scope input with a piece of wire JP9：This jumper should always be closed.
see display? flowchart to check
Yes
No
Troubleshooting
Press buttons. Do you see Check U5 and soldering
reaction on screen ? of button related pins No Power LCD Dark
Yes Notes: 1. All voltages are measured with volt meter's (-) pole at reference point (indicated
in photo below) and (+) pole at points of measurement.
USB powered Battery powered
Set cursor to timebase. Turn No Check U5 and soldering Is voltage at LCD No Check related
[ADJ] dial. Do you see of rotary encoder pins 2. Voltages with " *
" are measured when SW1 (couple) is placed at GND position. No No pin 19 5V?
timebase change ? Check USB Is VBUS measured ok? Battery voltage ok ? Check batt. connections
Yes （~1.6V） Yes Yes Yes
No （+5V） （-5V） （+5V） No No Possible LCD
Is AV+ normal (+5V) ? V5 No Short C and E of Q2.
Check L4, C29, C9, and C10 JP3 JP4 +5V JP7 V- JP8 JP9 AV+ AV- Check D4 Is V+ measured ok ？ Is V+ measured ok ? Check BOB2
（-5V） Does LCD light up? issue
Yes No Yes Yes Yes
Is V- normal (-5V) ? Check BOB5 and C27 No No
VBUS Is VS+ measured ok ? BOB3 installed ? Check JP2 Check Q2, R30 and
Yes No connection with U5
Is AV- normal (-5V) ? Check L1, C28, C11, and C12 (About +5V)
*
（0V ） No Yes Yes
V3
USB Check BOB4 Is +5V measured ok ? Check BOB3
Yes No
Is VA normal (+5V) ? Check L5, C16, and C17 Connector Yes
V2
Yes *
（0V ）
Power good
Set SW1, SW2, SW3 to GND, Powered by USB: V+ ≈VBUS - 0.7V V4
10mV, and X1 respectively Po wered by Ba tt.: V+ ≈ VBAT （~1.6V ） * No Display
V+ VB （0.6V）
Check Y1, C21, C22
No No Trace Volt at U4 pin20 too low ?
Is V2 measured 0V？ Check SW1, SW2, and R1 JP1
No
VT （2.6V） Press SW12. Does LED blink as it should be ? Re-program U4
Yes
No JP2 Ensure all analog voltages Yes
Is V3 measured 0V？ U1 may have been damaged No No
V1 （0V ） * are normal (see photo) Is contrast changeable by POT1? VEE.at LCD pin18 negative?
Yes No JP5 Yes Yes
is V4 measured ~1.6V？ Check SW3, R9, R10, R11 VA No
VT and VB normal? U3 damaged Check all connections between Check POT1 and related
Yes VBAT （+5V）
Yes U4 and LCD for opens or shorts.
Adjust VPOS. Can you see No Follow "No Trace" (Battery voltage) No
flowchart to check Connection between U4 Check out
trace displayed ? No
Battery VS+ SYSCL K Contrast JP6 LCD pin18 Signal Input pin17 and U3 pin12 good ? the cause U4 and LCD connection good ? Fix bad connections
Yes Connector Adj. Yes
Note: Keep JP2 open （2.5V） （About -5V） Yes
Done (Volt. range: 2 - 5V) Reference point for
Without BOB3：VS+ = V+ (due to JP2 closed) U3 has bad soldering
after the power-up tests voltage measurement
With BOB3：VS+ depends on state of BOB3 (On or Off) or has been damaged LCD defective
JYE Tech Ltd. - www.jyetech.com -