Electus Distribution Reference Data Sheet: HUMLOOP.

PDF (1)

EARTH LOOPS AND HUM

When you’re connecting up various pieces of audio cable itself. So we now have a continuous loop in the
equipment like amplifiers, tape decks, CD and DVD players, system’s earthing — an earth loop . But how does such an
vinyl record turntables and so on, it’s not unusual to find earth loop produce hum?
that the final system produces an audible humming sound Well, remember that in both of the mains cords, and also
from the speakers. This hum is usually at mains frequency in a lot of the building power wiring, the protective earth
(50Hz in countries like Australia and New Zealand, or wires are running very close to the ‘active’ mains wires, and
60Hz in countries like the USA) and/or its harmonics, and thus sharing some of their surrounding AC magnetic field.
it can occur even though the individual pieces of equipment That creates the opportunity for small AC voltages to be
may have excellent circuitry, and be performing entirely as induced in the earth wires themselves, by transformer
they should be. action. Also, there can quite often be small AC currents
As you may have heard, this kind of hum can be caused flowing in equipment earth leads anyway, due to ‘leakage’
by an earth loop in the overall system, created simply as a through EMI suppression capacitors and so on. And these
result of connecting the pieces of equipment together. And currents will set up small AC voltage drops in the earth
to remove the hum or at least reduce it to an acceptably wire of each piece of equipment.
low level, you generally need to track down the earth loop Because of the very low resistance around the earth loop
that’s causing it, and if possible prevent it from occurring. that has been set up, the resultant of these AC voltages will
This can sometimes be surprisingly difficult. tend to produce a corresponding current flowing around
To have the best chance of solving this kind of problem, the loop — and importantly, through the screening braid of
though, you need to understand what an earth loop is, how the audio cable and the earthy side of the signal circuitry at
they can be set up, and how to remove them. That’s what both ends.
we’ll try to achieve in this data sheet. So we now have a mains-frequency AC current (or ‘HUM
Hifi and home theatre or ‘AV’ amplifiers/receivers current’) flowing through the earthy side of the cable and
generally have a significant amount of exposed metalwork signal circuitry. And because this side of the cable and
such as speaker terminals, line input and output connectors circuitry inevitably has a small resistance of its own, this
and so on, connected directly to the internal circuitry. To means that a corresponding hum voltage drop will be
ensure that they’re as safe as possible to use, they are produced.
accordingly provided with a protective mains earth — in As far as the input of the amplifier is concerned, this hum
other words, a three-wire mains cord which includes an voltage VHUM is effectively added to the signal voltage VSIG ,
earth connection.
Other audio equipment
like tape decks,
turntables, CD players
and so on may also be
provided with a
protective earth, for the
same reason. As it
happens the most
common situation where
an earth loop can be set
up, and the easiest to
understand, is when you
connect two or more of
these earthed pieces of
equipment together. Let’s
see how, and also how
such a loop can produce
hum.
The diagram in Fig.1
shows a very basic audio
system with a cassette Fig.1: When there are two or more connections between the earths/commons of
tape deck connected to a two pieces of equipment, an earth loop is formed...
hifi amplifier (we’ve only
shown one channel, for
simplicity). As you can see both the amplifier and the tape as you can see from the equivalent circuit in Fig.2. So our
deck are provided with protective mains earths, so this amplifier is now being fed with not just the audio signal
means that the earth connections ultimately connect from the tape deck, but with a small hum signal as well.
together via the building’s power wiring, at the building And the weaker the signal itself is, the more likely you are
earth point. And if the common or ‘earthy’ side of the to be able to hear the hum.
signal circuitry inside each piece of equipment is also That explanation may be a bit over simplified, but it
connected to mains earth in each case, to maximise safety, shows the basic concept of earth loops and how they can
this means that the common side of the signal circuits are inject hum into audio systems.
also connected together via the building earth. The idea, then, is that wherever we end up with multiple
Now when you connect the amplifier’s line input to the earth paths which set up an earth loop, there’s the
tape deck’s output, via the usual screened audio cable, look potential for hum to be injected into our signal path. (This
what happens: there’s now a second connection between can even happen INSIDE equipment, by the way, so
the signal earths at each end, via the screen of the audio equipment designers have to take great care with their
 Electus Distribution Reference Data Sheet: HUMLOOP.PDF (2)
out. Another option is to remove the earth connection
from one end of one lead’s screening braid, in each
stereo pair.
In difficult cases it can help to run stereo connections
in ‘twin screened’ wire, with both signal wires enclosed
in a single common screen which is possibly only
connected to the earthy side of one connector at each
end (Fig.4). Then there won’t be a minor earth loop, but
there may be a small increase in signal crosstalk
between the two channels — probably not significant.
Another kind of earth loop that’s more subtle again,
and can be more difficult to solve, is a ‘virtual’ earth
loop. This can occur even with audio equipment that’s
nominally ‘double insulated’, and with no salient
Fig.2: When there is an earth loop, AC currents induced connection to earth. It tends to happen more often
in it can inject hum into the signal circuits via the when this equipment is fitted with a ‘switch mode’
screening braids of the interconnecting cables. power supply, which is more and more common.
The cause of the problem is that inside the
internal signal earthing techniques.) In theory, though, the equipment, there’s inevitably a small amount of capacitive
solution is simple: be careful not to set up any earth loops. and inductive coupling between the common side of the
Unfortunately in practice it’s often not that simple... signal circuitry and the incoming ‘active’ mains wiring. This
One approach that designers of low-level ‘front end’ happens through EMI suppression capacitors, stray
audio equipment (like tape decks, CD and DVD players, capacitance and the ‘stray’ magnetic field from the mains
turntables etc) have taken, in recent years, is to make this wiring itself (Fig.5). Now there’s also a link back from the
equipment effectively ‘double insulated’, so that it doesn’t active mains wiring itself to the building earth, both via
need a protective mains earth. Strictly speaking this isn’t magnetic and capacitive coupling again, and usually because
possible, of course, because truly double-insulated the mains neutral lead is ultimately earthed itself, as part of
electrical equipment doesn’t have ANY exposed metalwork the MEN (mains earthed neutral) system. This means that
connected to its active ‘works’. However by carefully even though the signal common of the equipment has no
ensuring that there’s a double layer of high quality nominal connection to earth, there can still be an earth
insulation to prevent all possibility of the equipment’s signal connection of sorts — albeit a fairly high impedance one,
circuitry ever becoming ‘live’ (even in the event of fire or and mainly via capacitance and magnetic coupling. So when
other drastic faults), the designers are able to ensure a this equipment is connected to an earthed amplifier, there
very high level of safety without the need for a protective is still the potential to set up a ‘virtual’ earth loop, and
mains earth. So more and more of this equipment is again inject a small amount of hum.
designed to have only a two-wire mains cord, without the There’s no easy way to remove this kind of virtual earth
earth wire that can so easily set up earth loops.
It’s much harder to do this with hifi and AV
amplifiers/receivers themselves, by the way, so
they’re generally still provided with a protective
earth (i.e., a three-wire mains cord). But you’d
perhaps expect that this shouldn’t cause any
problems, because if an earthed amplifier is used
with a set of front end equipment which all uses
this kind of ‘double insulation’, there should still
only be one connection to mains earth — and
hopefully no chance of an earth loop.
To a certain extent that’s true, too. However
even in this kind of system, without any obvious
earth loops, you can still get a small amount of
hum. So where does this hum come from?
Fig.3: Even a pair of stereo interconnecting cables can create
Well, there can be more subtle minor earth an earth loop...
loops set up. For example in modern stereo and
multi-channel surround sound systems, there are
often multiple audio cables connecting various
pieces of equipment — like the amplifier and a
CD or DVD player. As you can see from Fig.3,
the screens of these multiple cables can
themselves set up small earth loops of their
own. And with the fairly high level of AC fields
present in many modern homes and office
buildings, even this sort of earth loop can again
have small AC voltages induced in it.
The simplest way around this particular
problem is to ensure that stereo or other
multiple audio cables are run very closely
together, so there’s very little chance of
different AC voltages being induced in their
screening braids. That way, any induced voltages Fig.4: One solution is to use ‘twin screened’ leads with a
will tend to be identical and cancel each other single earth connection.
 Electus Distribution Reference Data Sheet: HUMLOOP.PDF (3)
loop entirely. All you can do is try to reduce its effect. One
approach that can often work quite well is to connect the
‘double insulated’ equipment to the mains via an isolating
transformer, rather than directly. This can reduce the
coupling back to earth via the mains wiring, and can reduce
the hum quite significantly. Unfortunately mains isolating
transformers are not cheap, though — even those with a
low power rating (which is all you need, in most cases).
Where it isn’t feasible to use an isolating transformer, it
sometimes helps to connect the metalwork of the ‘double
insulated’ equipment back to that of the system’s only
earthed item (i.e., the amplifier/receiver). This assumes that
there is no direct connection already, of course, via the
signal common. The extra connection may ‘short circuit’
the virtual earth path back via the mains wiring, and the
hum voltage induced in it, and thus achieve an
improvement.

What NOT to do!

Now that you know how earth loops tend to be set up,
and how they can cause hum to be injected into an audio
system, you might be tempted to try solving such problems
in an unsafe way. For example if you have a system with a
number of pieces of equipment that are fitted with mains Fig.5: Even with ‘double insulated’ equipment,
earths, and you’re getting hum, you might think that a there can be a ‘virtual earth’ — and a virtual
simple solution would be to simply disconnect the earth earth loop.
wires on every piece of equipment except the amplifier.
D o n ’ t d o i t . Tempting though it may seem, simply effect, via a higher-impedance link. Alternatively, you can
disconnecting the mains earth can be very dangerous in replace the piece of equipment concerned with a newer
equipment that has been designed and built to be earthed. model of the ‘double insulated’ type. This might well be
At the very least you might get a nasty ‘tingle’ when you’re cheaper than having it modified, anyway.
connecting the equipment up to the earthed amplifier,
because of capacitive and inductive coupling; at the worst, Remember, though: a hum may be annoying when you’re
either you or a loved one could easily be killed if the listening to music or watching a movie, but an electric
equipment should develop a fault. shock can be fatal. Don’t be tempted to ‘solve’ an annoying
problem by creating a potentially tragic one.
In the long run, a much safer approach is to have the
equipment properly and safely modified inside by a qualified (Copyright © 2001, Electus Distribution)
technician, to remove the direct connection between the
signal common and mains earth — or at least reduce its