Scribd
Upload
14 views

FPP Screen

The document provides instructions for installing and configuring front panel programming software on a MOTOTRBO radio. It includes steps to install an option board and option updater software, set up channels using CPS software, and navigate the front panel interface to program analog and digital channels. Programming includes settings like frequency, color code, tone, and talkgroup. The document provides detailed screenshots and explanations for completing the full configuration process.

Uploaded by

Cesar Lopez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
14 views

FPP Screen

The document provides instructions for installing and configuring front panel programming software on a MOTOTRBO radio. It includes steps to install an option board and option updater software, set up channels using CPS software, and navigate the front panel interface to program analog and digital channels. Programming includes settings like frequency, color code, tone, and talkgroup. The document provides detailed screenshots and explanations for completing the full configuration process.

Uploaded by

Cesar Lopez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 23

Front Panel Programming

User’s Guide

Edit channel 1
< 447.7000A >

Select Type
< Digital >

Tx Frequency
403.0000 MHz

http://www.itrbo.com/
version 1.1
Contents
Generic Option Board Installation 3

Initilal Setup with MOTOTRBO CPS 6

Option Updater Software Installation 11

Front Panel Programming Instructions 17


Generic Option Board Installation
1 Remove
precision
screws

2
Gently lift upward

3
Disconnect keyboard
4 Remove screws

5 Install Generic Option Board

6 Reassemble the radio by reversing the preceding steps.


Don’t forget to reconnect the keyboard.
Initial Setup with MOTOTRBO CPS
MOTOTRBO CPS must be installed and working in
order to create a zone and channels required by the
Front Panel Programming software.

To begin, connect your radio to your computer using


the USB programming cable. Start MOTOTRBO CPS
and follow the instructions shown on the following
pages.
Click “Read” in the menu bar

Choose “Expert” mode


in the “View” menu

Right-click “Channels”
to add a new Zone
Right-click your newly created zone and exactly one
analog channel and exactly one digital channel.

First, add an analog


channel. This must
be added before the
digital channel is
added.

Then add a digital


channel.

The “Option Board” check box


must be enabled for both
channels

Right-click the zone and rename it


to “FPP”
Click “Write” in the menu bar

Allow the programming to complete

To complete this stage of the setup process, power


your radio off, then on again.
Option Updater Software
Option Update Setup Wizard
Option Update Setup Wizard
Option Update Setup Wizard
Option Update Setup Wizard
Loading the Front Panel Programming HEX file onto
the radio.

Connect your radio to your PC


with the USB programming
cable, then click “Scan radios”

Choose “File” - “Select image...”


and locate the HEX update file
found in the Option Update
installation folder.

Once programming is complete,


turn the radio off, then on again.
Front Panel Programming Instructions
To enter Front Panel Programming mode on your
radio, select your newly created zone. Using the
knobs and keypad on your radio:

Press the “menu” button


Press the right arrow button twice
Press the “OK” button

Use the arrow buttons to navigate to your newly


created zone, then press the “OK” button
Press and hold back for 2 seconds,
then press #

Use the numeric keypad to enter


Enter License
your 10 digit license key.
0000000000 Press the ‘OK’ button when done.

OK

You are now in communications


mode.
Ch1 ---.----
Listen and talk from this screen.
#
Press ‘#’ to enter FPP configuration.

The PIN exists to prevent accidental


Enter PIN
programming. Enter ‘1234’ with the
1234 keypad, then press the ‘OK’ button.

OK
Programming Digital Channels

Choose the channel you would like


Edit channel 1
to configure using the left & right
< 447.7000A > arrow buttons, then press ‘OK’

OK

Select the signal type. Press ‘OK’ to


Select Type
continue.
< Digital >

OK

Enter the Rx frequency using the


Rx Frequency numeric keypad, then press the
403.0000 MHz ‘OK’ button

OK

Enter the Tx frequency, then press


Tx Frequency the ‘OK’ button.
403.0000 MHz

OK
Choose the color code you would
Color Code
like using the left & right arrow
< 3 > buttons, then press ‘OK’

OK

Choose ‘timeslot 1’ or ‘timeslot 2’


Timeslot
using the arrow buttons, then
< Slot 1 > press ‘OK

OK

Choose the call type:


Call Type
Group Call
< Group Call > Private Call
All Call
OK
The following screen varies,
depending on Call Type

Enter the Tx frequency, then press


Talkgroup the ‘OK’ button.
00000000

OK
Programming Complete

Saving
Channel 1
Programming Analog Channels

Choose the channel you would like


Edit channel 1
to configure using the left & right
< 447.7000A > arrow buttons, then press ‘OK’

OK

Select the signal type. Press ‘OK’ to


Select Type
continue.
< Analog 12.5 >

OK

Enter the Rx frequency using the


Rx Frequency numeric keypad, then press the
403.0000 MHz ‘OK’ button

OK

Enter the Tx frequency, then press


Tx Frequency the ‘OK’ button.
403.0000 MHz

OK
PL DPL CSQ
Rx Tone
< PL >

OK

Enter the Rx PL Tone using the


Rx PL Tone numeric keypad, then press the
067.0 ‘OK’ button

OK

PL DPL CSQ
Tx Tone
< PL >

OK

Enter the Tx PL Tone using the


Tx PL Tone numeric keypad, then press the
067.0 ‘OK’ button

OK
Programming Complete

Saving
Channel 1

You might also like