1-6911

Control Valves
1-6911 series Control valves

PARCOL 1-6911 series control valves provide the most versatile globe body type single seat available with heavy top guiding
design.
1-6911 series valves have an unusual combination of premium features that suit them for a wide range of applications,
including viscous fluids and slurries, with reduced costs.

Due to their simple construction and reduced number of parts, maintenance becomes easier and less expensive.
The 1-6911 series control valves can be supplied with a wide range of pneumatic actuators, on request, electric or hydraulic
ones for on-off or continuous control duty.

－2 －
Features and Advantages

Features Advantages

Large free-flow passages with smooth body contour and no - Higher Cv values
dead zones. - Reduced erosion and contamination
- Permit handling of slurries and viscous fluids

Heavy top guiding - Simple and cheaper construction

When the valve is open the plug is out of seat. - Compact plug design and smooth, contour assures a higher
stability.
- Reduced possibility of seizures.

Optimized seat diameters - Higher allowable pressure drops

1-6911 vavles are provided with minimum seat diameter above - Reduced sizes of actuators
which there are no substantial increases of Cv. - Better seat tightness when plug is in closed position.

Fewer body and trim parts - Low maintenance cost

Standard trim includes four parts only: plug, seat, stem and - Reduced inventory
pin. - Easier trim replacement
- Less possibility of damages

Wide range of components and accessories - Higher versatility

- Wide possibility of application

Wide selection of reduced capacity trims for each body size Safe and reliable
and large material selection.
PARCOL 1-X-290 multispring pneumatic actuators are
available and in addition electric ones and all possible
accessories.

Packing Temperature limits Maximum

Description
Type for standard bonnet (1) (2) Pressure (2)
TFK PTFE aramid fibers reinforced -10 ÷ +250 °C 150 bar
GRF Pure Flexible Graphite -10 ÷ +650 °C 400 bar
VTC 25% Glass loaded PTFE V-ring -10 ÷ +210 °C 250 bar

(1)
Inlet valve fluid temperature
(2)
Values listed for continuous service.
(3)
For additional information, please refer to PARCOL bulletin 1-VII “Packings for Control Valves”.

－3－
Main Specifications

Body Plug
- Type : Globe, single seat - Size : Full or reduced as per Cv table.

- Construction : Casting - Form : ≤12mm: Micro-flow

Forgings available (≤2”) ≥1/2”: Contoured
Characteristic:
- Linear
- Equal percentage
- Material : - standard: ASTM A216 WCB, - Quick opening
ASTM A351 CF8M
- on request:
Cr-Mo steel, special stainless - Guiding : Top guided
steel.
- Material : See materials of construction table.
- Size : 1/2” to 6” Standard construction AISI 316 with
or without stellite coatings.
Other materials on request.
- Connection : - flanged, UNI, ANSI, DIN

Stem

- Type : Threaded and pinned to the valve

- Rating : ANSI 150 - ANSI 300 plug.
PN 16 - PN 50
- Material : Highly polished AISI 316 with
maximum surface roughness 0.4 Ra
Other materials on request.
Bonnet

- Joint : Stud bolted

- Type : Standard, plain type Seat

- Type : Screwed into the valve body.

- Material : The same as the bodies, forgings
or castings - Material : The same as the valve plug.

- Leakage : IEC 60534-4 (ANSI B16.104)

- Packing box : Bolted type. Class IV, V.

Guide Bushing

- Type : Long, heavy and precision fitted into

the bonnet.

- Material : Refer to materials of construction

table.

－4 －
Flow coefficient Cv - Contoured plug

Equal Percentage Linear

Valve Size Port Size Seat Dia. Travel
inch. inch. mm Flow Flow Flow Flow
mm
to Open to Close to Open to Close
1/2 1/2 15 17 5.81 6.1 5.57 5.85
3/4 19 17 9.99 10.5 9.95 10.4
3/4
1/2 15 17 6.04 6.28 5.59 5.87
1 23 17 12.9 13.5 13.1 13.7
1 3/4 19 17 10.4 10.8 10.2 10.6
1/2 15 17 6.48 6.74 5.59 5.82
1.1/2 35 25 28.6 30 29.1 30.5
1.1/4 28 25 22 22.9 22.4 23.3
1 23 25 15.1 15.7 15.1 15.7
1.1/2
3/4 19 25 10.4 10.8 10.2 10.6
1/2 15 25 6.48 6.74 5.59 5.87
1/2 15 25 2.69 2.79 2.69 2.79
2 45 25 45.8 48 47.1 49.5
1.1/2 35 25 33.1 34.5 34.3 35.7
1.1/4 28 25 23.7 24.6 24.8 25.8
2 1 23 25 15.1 15.7 15.1 15.7
3/4 19 25 10.4 10.8 10.2 10.6
1/2 15 25 6.48 6.74 5.59 5.87
1/2 15 25 2.69 2.8 2.69 2.79
3 72 34 112 118 111 117
2.1/2 60 34 88.4 92 88.5 92
2 45 34 58.1 60.4 58 60.3
3
1.1/2 35 34 33.1 34.5 34.3 35.7
1.1/4 28 34 23.7 24.6 24.8 25.8
1 23 34 15.1 15.7 15.1 15.7
4 86 45 187 196 - -
3 72 45 138 144 138 144
2.1/2 60 45 107 111 107 111
4
2 45 45 58.1 60.4 58 60.3
1.1/2 35 45 33.1 34.5 34.3 35.7
1.1/4 28 45 23.7 24.6 24.8 25.8
6 130 60 388 407 - -
5 110 60 312 325 - -
6 4 86 60 232 242 - -
3 72 60 138 144 176 183
2.1/2 60 60 107 111 125 129

Flow coefficient Cv - Microflow plug

Equal Percentage Linear

Valve Size Port Size Seat Dia. Travel
inch inch mm mm Flow Flow Flow to Flow
to Open to Close Open to Close

17 0.645 0.671 0.645 0.671

1/4 6
17 1 1.04 1 1.04
1/2
3/4 17 1.67 1.73 1.67 1.73
1 3/8 9
17 2.52 2.62 2.52 2.63
1/2 12 17 4 4.16 4 4.16

－5－
Valve assembly

24
17
23

27

2
4
12
3

8 5

Item Part Name

1 Body
2 Bonnet
3 Stud
4 Nut
5 Plug
6 Seat
7 Stem
8 Gasket
9 Guide bushing
12 Pin
17 Packing flange
23 Stud
24 Nut
27 Packing

－6 －
Materials of construction

Basic Class
Item Part Name
A F G H L
1 Body SA216 WCB SA352 LCB AISI 316 AISI 316L AISI 304
2 Bonnet SA105 SA350 LF2 AISI 316 AISI 316L AISI 304
3 Stud SA193 B7 SA193 B7 SA193 B7
4 Nut SA194 2H SA194 2H SA194 2H
5 Plug See Subclass Table
6 Seat See Subclass Table
7 Stem See Subclass Table
8 Gasket Inorganic fibers, asbestos free ≤ 300°C ；Pure graphite reinforced steel > 300°C
9 Guide Bushing See Subclass Table
12 Pin See Subclass Table
17 Packing Flange A105 A105 AISI 316 AISI 316 AISI 316
23 Stud AISI 304
24 Nut AISI 304
TFK – PTFE Aramid fibers reinforced PTFE
27 Packing (1) GRF – Flexible graphite
VTC – PTFE Glass loaded PTFE V-ring

Item 5 6 7 9 12
Name Plug Seat Stem Guide Bushing Pin
01 AISI 316 AISI 316
02 AISI 316 Seat joint stellite AISI 316 Seat joint stellite AISI 316 AISI 316 Cr plated
Subclass

03 AISI 316 Fully stellited AISI 316 Fully stellited

04 AISI 316L AISI 316L
05 AISI 316L Seat joint stellite AISI 316L Seat joint stellite AISI 316L AISI 316L Cr plated
06 AISI 316L Fully stellited AISI 316L Fully stellited
07 A182 F6NM Nitrided AISI 410 35HRC
A182 F6NM Nitrided (7)
08 A182 F6NM Nitrided A182 F6NM Fully stellited AISI 316L
AISI 316
09 AISI 316 22HRC MAX. AISI 316 22HRC MAX.
22HRC MAX.
10 AISI 316 22HRC MAX. seat joint stellite AISI 316 22HRC MAX. seat joint stellite AISI 316 Cr plated
NACE MR-01-75

11 AISI 316 22HRC MAX. fully stellited AISI 316 22HRC MAX. fully stellited
12 AISI 316L 22HRC MAX. AISI 316L 22HRC MAX.
AISI 316L
13 AISI 316L 22HRC MAX. seat joint stellite AISI 316L 22HRC MAX. seat joint stellite AISI 316L Cr plated
22HRC MAX.
14 AISI 316L 22HRC MAX. fully stellited AISI 316 L22HRC MAX. fully stellited
15 A182 F6NM 23HRC MAX. nitrided A182 F6NM 23HRC MAX. fully stellited AISI 316L A182 F6NM Nitrided
16 MONEL K500 35HRC MAX MONEL K500 35HRC MAX MONEL 400 MONEL 400 (2)

(1)
For additional information, refer to bulletin 1-VII.
(2)
Stem welded to plug.

－7－
Available combinations and temperature limits - °C

Subclass DN
01 04 02-03 05-06 07 08 09 12 10-11 13-14 15 16 inch.
1/2”- 2”
A -20 ÷ +400 -20 ÷ +400
-20 ÷ +400 -29 ÷ +400
-20 ÷ +400 -20 ÷ +400
-20 ÷ +400 -20 ÷ +400 3”- 4”
A216 WCB
-20 ÷ +250 -20 ÷ +250 -20 ÷ +250 -20 ÷ +250 6”
1/2”- 2”
F -45 ÷ +340 -45 ÷ +340
-45 ÷ +340 -45 ÷ +340
-45 ÷ +340 -45 ÷ +340
45 ÷ +340 -45 ÷ +340 3”- 4”
A352 LCB
-45 ÷ +250 -45 ÷ +250 -45 ÷ +250 -45 ÷ +250 6”
Basic class

-29 ÷ +400 1/2”- 2”

G -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +320 3”- 4”
AISI 316
-29 ÷ +190 6”
-29 ÷ +400 1/2”- 2”
H -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +320 3”- 4”
AISI 316L
-29 ÷ +190 6”
-29 ÷ +400 1/2”- 2”
L -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400
-20 ÷ +400 -20 ÷ +400
-29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +400 -29 ÷ +320 3”- 4”
AISI 304
-20 ÷ +250 -20 ÷ +250 -29 ÷ +190 6”
Stainless steel MONEL
Stainless steel for corrosion service TRIM
Application STD Application
trim
N.A.C.E. MR-01-75

Notes:
- The listed temperatures are those of the fluid at valve inlet.
- The subclass corresponding to the blanks are available only on request.

－8 －
Overall dimensions (1) - mm

(2)
Size Travel Face to Face “A” Dimension Dimension B Dimension C
inch. mm ANSI 150 ANSI 300 ANSI 150 ANSI 300 ANSI 150÷300
1/2 17 184 190 61 61 144
3/4 17 184 194 61 61 144
1 17 184 197 65 65 155
1.1/2 25 222 235 82 82 192
2 25 254 267 87 87 196
3 34 298 317 120 120 232
4 45 352 368 135 135 279
6 60 451 473 167 170 353

Weights - kg
Size
ANSI 150 ANSI 300
inch.
1/2 12 12
3/4 12 12
1 13 14
1.1/2 23 23
2 28 28
3 42 53
4 62 73
6 123 152

(1)
ANSI 150 overall dimensions are also valid for PN16
ANSI 300 overall dimensions are also valid for PN25-40
(2)
A” ±1.5 mm
Tolerance on face to face “A” dimension: ±1.5 mm.

－9－
1-X-290 Multi-spring pneumatic diaphragm actuator overall dimensions - mm

Actuator Size
Dimension
D25 D33 D39 D46 D63
A 487 510 574 644 796
B 262 333 395 465 640
D M12 M12 M18x1.5 M18x1.5 M24x2
F 1/4” 1/2” 3/4” 3/4" 1”
G 150 150 250 250 300
L 300 300 365 365 455
M 200 200 252 252 330
N 380 380 470 570 570

Weights - kg

Handwheel
Actuator (To be added)
Direct Reverse
Size Side Top
Mounted Mounted
D25 15 15 +10 +6
D33 22 22 +10 +6
D39 33 33 +19 +15
D46 54 54 +19 +15
D63 120 120 +13 -

－10 －
－ 11 －