All-in-one solar charger inverter

User Manual

Product models:

HF2430S80-H ｜ HF2430U80-H

Solar charge inverter V2.0 1

 Important safety instructions

Please keep this manual for future use.

This manual contains all safety, installation and operating instructions for the HF24-H Series all-in-one
solar charge inverter.
Please read all instructions and precautions in the manual carefully before installation and use.
 Non-safety voltage exists inside the all-in-one solar charge inverter. To avoid personal injury, users
shall not disassemble the all-in-one solar charge inverter themselves. Contact our professional
maintenance personnel if their is a need for repair.
 Do not place the all-in-one solar charge inverter within the reach of children.
 Do not install the all-in-one solar charge inverter in harsh environments such as moist, oily,
flammable or explosive, or heavily dusty areas.
 The mains input and AC output are high voltage, so please do not touch the wiring terminals.
 The housing of the all-in-one solar charge inverter is hot when it is working. Do not touch it.
 Do not open the terminal protective cover when the all-in-one solar charge inverter is working.
 It is recommended to attach proper fuse or circuit breaker to the outside of the all-in-one solar
charge inverter.
 Always disconnect the fuse or circuit breaker near the terminals of PV array, mains and battery before
installing and adjusting the wiring of the all-in-one solar charge inverter.
 After installation, check that all wire connections are tight to avoid heat accumulation due to poor
connection, which is dangerous.
 The all-in-one solar charge inverter is off-grid. It is necessary to confirm that it is the only input device
for load, and it is forbidden to use it in parallel with other input AC power to avoid damage.

Solar charge inverter V2.0 2

 CONTENTS

1. GENERAL INFORMATION ........................................................................................... 4

1.1 PRODUCT OVERVIEW AND FEATURES .................................................................................. 4
1.2 BASIC SYSTEM INTRODUCTION .......................................................................................... 5
1.3 APPEARANCE ............................................................................................................... 6
1.4 DIMENSION DRAWING .................................................................................................... 7
2. INSTALLATION INSTRUCTIONS .................................................................................. 8
2.1 INSTALLATION PRECAUTIONS ............................................................................................ 8
2.2 WIRING SPECIFICATIONS AND CIRCUIT BREAKER SELECTION ...................................................... 9
2.3 INSTALLATION AND WIRING ........................................................................................... 11
3. OPERATING MODES ................................................................................................ 17
3.1 CHARGING MODE ........................................................................................................ 17
3.2 OUTPUT MODE ........................................................................................................... 18
4. LCD SCREEN OPERATING INSTRUCTIONS ................................................................. 19
4.1 OPERATION AND DISPLAY PANEL .................................................................................... 19
4.2 SETUP PARAMETERS DESCRIPTION .................................................................................. 23
4.3 BATTERY TYPE PARAMETERS .......................................................................................... 29
5. OTHER FUNCTIONS ................................................................................................. 31
5.1 DRY NODE ................................................................................................................. 31
5.2 RS485 COMMUNICATION PORT ..................................................................................... 31
5.3 CAN COMMUNICATION FUNCTION ................................................................................... 31
5.4 USB COMMUNICATION PORT ......................................................................................... 31
6. PROTECTION ........................................................................................................... 32
6.1 PROTECTIONS PROVIDED ............................................................................................... 32
6.2 FAULT CODE MEANING ................................................................................................. 34
6.3 HANDLING MEASURES FOR PART OF FAULTS ....................................................................... 35
7. SYSTEM MAINTENANCE .......................................................................................... 36
8. TECHNICAL PARAMETERS ....................................................................................... 37

Solar charge inverter V2.0 3

1. General information
1.1 Product overview and features
HF24-H series is a new all-in-one hybrid solar charge inverter, which integrates solar energy storage &
means charging energy storage and AC sine wave output. Thanks to DSP control and advanced control
algorithm, it has high response speed, high reliability and high industrial standard. Four charging modes
are optional, i.e. Only Solar, Mains Priority, Solar Priority and Mains & Solar hybrid charging; and two
output modes are available, i.e. Inverter and Mains, to meet different application requirements.
The solar charging module applies the latest optimized MPPT technology to quickly track the maximum
power point of the PV array in any environment and obtain the maximum energy of the solar panel in
real time.
Through a state of the art control algorithm, the AC-DC charging module realizes fully digital voltage
and current double closed loop control, with high control precision in a small volume. Wide AC voltage
input range and complete input/output protections are designed for stable and reliable battery charging
and protection.
Based on full-digital intelligent design, the DC-AC inverter module employs advanced SPWM technology
and outputs pure sine wave to convert DC into AC. It is ideal for AC loads such as household appliances,
power tools, industrial equipment, and electronic audio and video equipment. The product comes with
a segment LCD display design which allows real-time display of the operating data and status of the
system. Comprehensive electronic protections keep the entire system safer and more stable.
Features:
1. Full digital voltage and current double closed loop control, advanced SPWM technology, output
of pure sine wave.
2. Two output modes: mains bypass and inverter output; uninterrupted power supply.
3. Available in 4 charging modes: Only Solar, Mains Priority, Solar Priority and Mains & Solar hybrid
charging.
4. Advanced MPPT technology with an efficiency of 99.9%.
5. Designed with a LCD screen and 3 LED indicators for dynamic display of system data and
operating status.
6. ON/OFF rocker switch for AC output control.
7. Power saving mode available to reduce no-load loss.
8. Intelligent variable speed fan to efficiently dissipate heat and extend system life.
9. Lithium battery activation by PV solar or mains, allowing access of lead-acid battery and lithium
battery.
10. 360 ° all-round protection with a number of protection functions.
11. Complete protections, including short circuit protection, over voltage and under voltage
protection, overload protection, reverse protection, etc.

Solar charge inverter V2.0 4

1.2 Basic system introduction
The figure below shows the system application scenario of this product. A complete system consists of
the following parts:
1. PV module: Convert light energy into DC power, and charge the battery through the all-in-one
solar charge inverter, or directly invert into AC power to drive the load.
2. Mains or generator: Connected at the AC input, to power the load while charging the battery. If
the mains or generator is not connected, the system can also operate normally, and the load is powered
by the battery and PV module.
3. Battery: Provided to ensure normal power supply to the system loads when solar energy is
insufficient and the Mains is not connected.
4. Household load: Allow connection of various household and office loads, including refrigerators,
lamps, TVs, fans and air conditioners.
5. All-in-one solar charge inverter: The energy conversion unit of the whole system.
Specific system wiring method depends on the actual application scenario.

Solar charge inverter V2.0 5

1.3 Appearance

① AC input port ⑨ Cooling fan

② AC output port ⑩ Battery port

③ CAN communication port ⑪ Cooling fan

④ USB communication port ⑫ ON/OFF rocker switch

⑤ RS485 communication port ⑬ PV port

⑥ Dry contact port ⑭ Touch the key lightly

⑦ Grounding screw hole ⑮ LED Indicator

⑧ Overload protector ⑯ LCD screen

Solar charge inverter V2.0 6

1.4Dimension drawing

Solar charge inverter V2.0 7

2. Installation instructions
2.1 Installation precautions
Please read this manual carefully prior to installation to familiarize yourself with the installation
steps.
 Be very careful when installing the battery. Wear safety goggles when installing a lead-acid
liquid battery. Once coming into contact with the battery acid, rinse with clean water timely.
 Do not place metal objects near the battery to prevent short-circuit of the battery.
 Acid gas may be generated when the battery is charged. So, please ensure good ventilation.
 When installing the cabinet, be sure to leave enough space around the all-in-one solar charge
inverter for heat dissipation. Do not install the all-in-one solar charge inverter and lead-acid
battery in the same cabinet to avoid corrosion by acid gas generated during battery operation.
 Only the battery that meets the requirements of the all-in-one unit can be charged.
 Poorly connected connections and corroded wires may cause great heat which will melt the
wire insulation, burn the surrounding materials, and even cause fires. So, make sure the
connectors have been tightened, and the wires are secured with ties to avoid looseness of
connections caused by shaking of wires during mobile application.
 The system connection wires are selected according to a current density of not more than 5
A/mm2.
 Avoid direct sunlight and rainwater infiltration for outdoor installation.
 Even after the power is turned off, there is still high voltage inside the unit. Do not open or
touch the internal components, and avoid related operations until the capacitor completely
discharges.
 Do not install the all-in-one solar charge inverter in harsh environments such as moist, oily,
flammable or explosive, or heavily dusty areas.
 Polarity at the battery input end of this product shall not be reversed, otherwise it may
damage the device or cause unpredictable danger.
 The mains input and AC output are high voltage, so please do not touch the wiring terminals.
 When the fan is working, do not touch it to prevent injury.
 Load equipment input power needs to confirm that this all-in-one solar charge inverter is the
only input device, and it is forbidden to use in parallel with other input AC power to avoid
damage. It is necessary to confirm that the solar charge inverter is the only input device for
load equipment, and it is forbidden to use it in parallel with other input AC power to avoid
damage.

Solar charge inverter V2.0 8

2.2 Wiring specifications and circuit breaker selection

Wiring and installation must comply with national and local electrical codes.
Recommended PV array wiring specifications and circuit breaker selection: Since the output current of
the PV array is affected by the type, connection method and illumination angle of the PV module, the
minimum wire diameter of the PV array is calculated according to its short-circuit current; refer to the
short-circuit current value in the PV module specification (the short-circuit current is constant when the
PV modules are connected in series; the short-circuit current is the sum of the short-circuit currents of
all PV modules connected in parallel); the short-circuit current of the PV array shall not exceed the
maximum input current.

 Refer to the table below for PV input wire diameter and switch:

Recommended PV Maximum PV Recommended air switch or

Models
wiring diameter input current circuit breaker type

HF2430S80-H 3.5mm2/12AWG 13A 2P—25A

HF2430U80-H 3.5mm2/12AWG 13A 2P—25A

Note: The voltage in series shall not exceed the maximum PV input open circuit voltage.

 Refer to the table below for recommended AC input wire diameter and switch:

Recommended AC Maximum bypass Recommended air switch

Models
input wiring diameter input current or circuit breaker type

2
HF2430S80-H 6mm /10AWG 30A 2P—40A

2
HF2430U80-H 6mm /10AWG 40A 2P—40A

Note: There is already an appropriate circuit breaker at the Mains input wiring terminal, so it is

not necessary to add one more.

Solar charge inverter V2.0 9

 Recommended battery input wire diameter and switch selection

Recommended Rated battery Maximum Recommended air

Models battery wiring discharge charge switch or circuit breaker
diameter current current type

HF2430S80-H 30mm2/2AWG 135A 80A 2P—160A

HF2430U80-H 30mm2/2AWG 135A 80A 2P—160A

 Recommended AC output wiring specifications and circuit breaker selection

Recommended Rated Maximum Recommended air

Models AC output wiring inverter AC bypass output switch or circuit breaker
diameter output current type

2
HF2430S80-H 6mm /10AWG 14.4A 30A 2P—40A

2
HF2430U80-H 6mm /10AWG 27.5A 40A 2P—40A

Note: The wiring diameter is for reference only. If the distance between the PV array and the all-in-one

solar charge inverter or the distance between the all-in-one solar charge inverter and the battery is

relatively long, using a thicker wire can reduce the voltage drop to improve system performance.

Note: The above are only recommended wiring diameter and circuit breaker. Please select the

appropriate wiring diameter and circuit breaker according to actual situations.

Solar charge inverter V2.0 10

2.3 Installation and wiring
Installation steps:：
Step 1: Determine the installation position and the space for heat dissipation. Determine the installation
position of the all-in-one solar charge inverter, such as wall surface; when installing the all-in-one solar
charge inverter, ensure that there is enough air flowing through the heat sink, and space of at least 200m
to the left and right air outlets of the inverter shall be left to ensure natural convection heat dissipation.
Refer to the installation diagram of the whole machine as above.

Warning: Danger of explosion! Never install the all-in-one solar charge inverter and lead-acid
battery in the same confined space! Also do not install in a confined place where battery gas may
collect.

Solar charge inverter V2.0 11

Step 2: Remove the terminal cover

Step3: Wiring

AC input / output wiring method:

① Prior to AC input/output wiring, disconnect the external circuit breaker and confirm that the
wire used is thick enough. Please refer to Section 2.2 “Wiring Specifications and Circuit Breaker
Selection”;
② Properly connect the AC input wire according to the wire sequence and terminal position
shown in the figure below. Please connect the ground wire first, and then the live wire and the
neutral wire;

Solar charge inverter V2.0 12

 ：Ground L：Live N：Neutral

③ Properly connect the AC output wire according to the wire sequence and terminal
position shown in the figure below. Please connect the ground wire first, and then the live
wire and the neutral wire. The ground wire is connected to the grounding screw hole on the
cabinet through the O-type terminal.

：Ground L：Live N：Neutral

Note: The grounding wire shall be as thick as possible (cross-sectional area is not less than 4mm2).

The grounding point shall be as close as possible to the all-in-one solar charge inverter. The
shorter the grounding wire, the better.

Solar charge inverter V2.0 13

PV input wiring method:
① Prior to wiring, disconnect the external circuit breaker and confirm that the wire used
is thick enough. Please refer to Section 2.2 “Wiring Specifications and Circuit Breaker
Selection”;
② Properly connect the PV input wire according to the wire sequence and terminal
position shown in the figure below.

PV+: PV input positive pole PV-: PV input negative pole

BAT wiring method:

① Prior to wiring, disconnect the external circuit breaker and confirm that the wire used
is thick enough. Please refer to Section 2.2 “Wiring Specifications and Circuit Breaker
Selection”. The BAT wire needs to be connected to the machine through the O-type
terminal. The O-type terminal with an inner diameter of 5 mm is recommended. The O-type
terminal shall firmly press the BAT wire to prevent excessive heat generation caused by
excessive contact resistance;
② Properly connect the BAT wire according to the wire sequence and terminal position
shown in the figure below.

Solar charge inverter V2.0 14

 BAT+: Battery positive electrode BAT-: Battery negative electrode

Warnings:

① Mains input, AC output and PV array will generate high voltage. So, before wiring, be sure to

disconnect the circuit breaker or fuse;

② Be very careful during wiring; do not close the circuit breaker or fuse during wiring, and ensure that

the “+” and “-” pole leads of each component are connected properly; a circuit breaker must be

installed at the battery terminal. Refer to Section 2.2 “Wiring Specifications and Circuit Breaker Selection”

to select a right circuit breaker. Before wiring, be sure to disconnect the circuit breaker to prevent strong

electric sparks and avoid battery short circuit; if the all-in-one solar charge inverter is used in an area

with frequent lightning, it is recommended to install an external lightening arrester at the PV input

terminal.

Step 4: Check if the wiring is correct and firm. In particular, check if the battery polarity is reversed, if the

PV input polarity is reversed and if the AC input is properly connected.

Solar charge inverter V2.0 15

Step 5: Install the terminals cover.

Step 6: Turn on the all-in-one solar charge inverter

First, close the circuit breaker at the battery terminal, and then turn the rocker switch
on the left side of the machine to the "ON" state. The "AC/INV" indicator flashing
indicates that the inverter is working normally. Close the circuit breakers of the PV
array and the Mains. Finally, turn on AC loads one by one as the AC output is normal
to avoid a protection action caused by a large momentary shock due to simultaneous
turning on the loads simultaneously. Now, the machine goes into a normal
operation according to the set mode.

Note: If power is supplied to different AC loads, it is recommended to first turn on the load with a large
surge current. After the load is stable, turn on the load with a small surge current.

Note: If the all-in-one solar charge inverter does not work properly or the LCD or indicator is abnormal,
refer to Chapter 6 to handle the exceptions.

Solar charge inverter V2.0 16

3. Operating modes
3.1 Charging mode
1) PV priority: PV module will charge the battery preferentially, and the battery is charged by the
Mains only when the PV system fails. During the day, solar energy is fully used to charge, while at
night, it converts to the Mains. This can maintain battery level, and is ideal for areas where the grid
is relatively stable and electricity price is relatively high.

2) Mains priority: The Mains supply is preferentially used to charge the battery. Only when the Mains
fails, the PV charging can be activated.

3) Hybrid charging: PV and mains hybrid charging. PV MPPT charging is a priority, and when PV
energy is insufficient, the mains supply supplements. When the PV energy is sufficient again, the
mains stops charging. This is the fastest charging mode, suitable for the areas where power grid is
unstable, providing sufficient backup power supply at any time.

4) Only Solar (Only Solar): Only PV charging, without Mains charging. This is the most energy-
efficient way in which battery is charged only by solar panels, and is usually used in areas with
good lighting conditions.

Solar charge inverter V2.0 17

3.2 Output mode
 PV priority mode:
Switch to mains supply when the PV charging fails. This mode maximizes the use of solar energy
while maintaining battery power, suitable for use in the areas with relatively stable grid.

 Mains priority mode:

Switch to inverter only when the mains fails (when there was mains power, switch to mains power
for charging and power supply).Then, the unit is equivalent to a backup UPS, suitable for areas
with unstable grid. Switching does not affect PV charging.

 Inverter priority mode:

Switch to mains supply only when the battery discharge undervoltage is lower than the set point
(item 04). When the charging battery is higher than the set point of (05 setting item), switch to
the battery discharge mode. This can cycle the battery charge and discharge. This mode maximizes
the use of DC power and is used in the area with stable grid. Switching does not affect PV charging.

Solar charge inverter V2.0 18

4. LCD screen operating instructions
4.1 Operation and display panel
The operation and display panel is as shown below, including 1 LCD screen, 3 indicators and 4 operation
buttons.

Operation buttons introduction

Function
Description
buttons

SET Enter/Exit Settings menu

UP Previous choice

DOWN Next choice

ENT Confirm/Enter Options under the settings menu,

Indicators introduction

Indicators Colors Description

Steady on: Mains output

AC/INV Yellow
Flash: Inverter output

Flash: Battery charging

CHARGE Green
Steady on: Charging completed

FAULT Red Flash : Fault state

Solar charge inverter V2.0 19

LCD screen introduction

Icons Functions Icons Functions

Indicates that the AC input

Indicates that the inverter circuit
terminal has been connected to
is working
the grid
Indicates that the AC input mode Indicates that the machine is in
in APL mode (wide voltage range) the Mains Bypass mode
Indicates that the PV input terminal
Indicates that the AC output is in
has been connected to the solar
an overload state
panel

Indicates that the machine has Indicates the percentage of AC

been connected to the battery: output loads:

indicates that the remaining indicates that the load

battery is 0%~24%; percentage is 0%~24%;

indicates that the remaining indicates that the load

battery is 25%~49%; percentage is 25%~49%,

indicates that the remaining indicates that the load

battery is 50%~74%; percentage is 50%~74%,

indicates that the remaining indicates that the load

battery is 75%~100%. percentage is ≥75%.
Indicates that the battery type of Indicates that the buzzer is not
the machine is a lithium battery enabled

Solar charge inverter V2.0 20

 Indicates that the current battery
Indicates that the machine has an
type of the machine is a lead-acid
alarm
battery
Indicates that the battery is in Indicates that the machine is in a
charging state fault condition
Indicates that the AC/PV charging Indicates that the machine is in
circuit is working setup mode

The parameters displayed in the

middle of the screen:
1. In the non-setup mode, the
Indicates that the AC output
alarm or fault code is displayed.
terminal has an AC voltage output
2. In the setup mode, the
currently set parameter item code
is displayed.

Parameters display on the left side of the screen: input parameters

Indicates AC input

Indicates PV input

Indicates inverter circuit

This icon is not displayed

Display battery voltage, battery charge total current, mains charge power, AC input
voltage, AC input frequency, PV input voltage, internal heat sink temperature,
software version

Parameters display on the right side of the screen: Output parameters

Indicates output voltage, output current, output active power, output apparent
power, battery discharge current, software version; in setup mode, displays the set
parameters under the currently set parameter item code

Arrow display

Indicates the charging circuit

① The arrow is not displayed ⑤
charging the battery terminal
Indicates the grid supplying power
② ⑥ The arrow is not displayed
to the load
Indicates the battery terminal
Indicates grid supplying power to
③ ⑦ supplying power to the inverter
the charging circuit
circuit
Indicates PV module supplying Indicates the inverter circuit
④ ⑧
power to the charging circuit supplying power to the load

Solar charge inverter V2.0 21

Real-time data viewing method

On the LCD main screen, press the “UP” and “DOWN” buttons to scroll through the real-time data

of the machine.

Parameters
Parameters on the left side of the in the Parameters on the right
Page
screen middle of side of the screen
the screen

INPUT BATT V OUTPUT LOAD V (Output

1
(Battery input voltage) load voltage)

PV TEMP ℃ PV OUTPUT KW
2
(PV charger heatsink temperature) (PV output power)

PV INPUT V PV OUTPUT A
3
(PV input voltage) (PV output current)

INPUT BATT A OUTPUT BATT A

4
(Input battery current) (Battery output current)

INPUT BATT KW OUTPUT BATT KW

5
(Battery input power) (Battery output power)

AC INPUT Hz AC OUTPUT LOAD Hz

6
(AC input frequency) (AC output frequency)
Fault code
AC INPUT V AC OUTPUT LOAD A
7
(AC input voltage) (AC output load current)

INPUT V OUTPUT LOAD KVA

8
(For maintain) (Load apparent power)

INV TEMP ℃
INV OUTPUT LOAD KW
9 (AC charge or battery discharge
(Load active power)
heatsink temperature)

Bootloader software
10 APP software version
version

Model Output Power

11 Model Battery Voltage Rating
Rating

12 Model PV Voltage Rating Model PV Current Rating

Solar charge inverter V2.0 22

4.2 Setup parameters description
Buttons operation instructions: Press the “SET” button to enter the setup menu and exit the setup
menu. After entering the setup menu, the parameter number [00] will flash. At this point, press the “UP”
and “DOWN” buttons to select the code of parameter item to be set. Then, press the “ENT” button
to enter the parameter editing mode, and the value of the parameter is flashing. Adjust the value of the
parameter with the “UP” and “DOWN” buttons. Finally, press the “ENT” button to complete the
parameter editing and return to the parameter selection state.

Parameter Parameter
Settings Description
no. name

Exit setting
00 [00] ESC Exit the setup menu
menu

PV priority mode, switching to the Mains when

[01] SOL the PV fails or the battery is lower than the set
value of parameter [04].

Output source Mains priority mode, switching to inverter only

01 [01] UTI default
priority when the mains fails.

Inverter priority mode, switching to the mains

[01] SBU only when the battery is under voltage or lower
than the set value of parameter [04].
Bypass self-adaptation; when the mains is
[02] 50.0 connected, it automatically adapts to the mains
Output frequency; when the mains is disconnected, the
02
Frequency output frequency can be set through this menu.
[02] 60.0 The default output frequency of the 230V
machine is 50HZ, and the 120V machine 60HZ.
Wide mains input voltage range of 230V
machine: 90~280V
[03] APL
Mains input voltage range of 120V machine:
AC Input 90~140V
03
Voltage Range Narrow mains input voltage range of 230V
machine: 170~280V
[03] UPS default
Mains input voltage range of 120V machine:
90~140V
Battery Power When the parameter [01] =SOL/SBU, the
[04] 21.8V
04 to Utility battery voltage is lower than the set value, and
default
Setpoint the output is switched from the inverter to the

Solar charge inverter V2.0 23

 Parameter Parameter
Settings Description
no. name

mains. Setting range: 20V~26V. Cannot exceed

the value of [14] settings.
When the parameter [01] =SOL/SBU, the
Utility to battery voltage is higher than the set value, and
[05]28.8V
05 Battery Power the output is switched from the mains to the
default
Setpoint inverter. Setting range: 24V~30V. Cannot be
lower than the value of [04] / [35] settings.

PV priority charging; only when the PV

[06] CSO
charging fails, the mains charging is started.

Mains priority charging; only when the mains

[06] CUB
charging fails, the PV charging is started.

PV and Mains hybrid charging; PV charging is a

priority, and when the PV energy is insufficient,

Charger source the Mains charging supplements. When the PV

06
priority energy is sufficient, the Mains charging stops.
[06] SNU default Note: Only when the Mains bypass output is
loaded, the PV charging and the mains
charging can work at the same time. When the
inverter works, only the PV charging can be
started.

Only PV charging, with the Mains charging not

[06] OSO
activated.

Max charger Max charger current (AC charger+PV charger).

07 [07] 60A default
current Setting range: 0~80A；

[08] USE User-defined; all battery parameters can be set.

Sealed lead-acid battery; constant-voltage

[08] SLd charge voltage: 28.8V, floating charge voltage:
08 Battery Type
27.6V.
Vented lead-acid battery; constant-voltage
[08] FLd charge voltage: 29.2V, floating charge voltage:
27.6V.

Solar charge inverter V2.0 24

 Parameter Parameter
Settings Description
no. name

Colloidal lead-acid battery; constant-voltage

[08] GEL default charge voltage: 28.4V, floating charge voltage:
27.6V.
Lithium iron phosphate battery LF07/LF08/LF09,
corresponding to 7 strings ,8 strings and 9
strings of lithium iron phosphate battery; for 7
[08] strings, default constant-voltage charge voltage
LF07/LF08/LF09 is 24.8V; for 8 strings, default constant-voltage
charge voltage is 28.4V; for 9 strings, default
constant-voltage charge voltage is 31.8V; allow
adjustable.
Ternary lithium battery; the default constant-
[08] NCA voltage charge voltage is 28.4V, which is
adjustable.
Boost charge voltage setting; the setting range
Battery boost [09] 28.8V
09 is 24V~29.2V, with step of 0.2V; it is valid for
charge voltage default
user-defined battery and lithium battery.
Boost charge maximum time setting, which
means the maximum charging time to reach
the set voltage of parameter [09] during
Battery boost
10 [10] 120 default constant-voltage charging. The setting range is
charge time
5min~900min, with a step of 5 minutes. It is
valid for user-defined battery and lithium
battery.
Floating charge voltage, setting range:
Battery floating [11] 27.6V
11 24V~229.V, step: 0.2V, valid when battery type
charge voltage default
is user-defined.
Over-discharge voltage; when the battery
Battery over voltage is lower than this judgment point, delay
discharge the time set by parameter [13] and turn off
12 [12] 21V default
voltage (delay inverter output. Setting range is 20V~24V, with
off) a step of 0.2V. It is valid for user-defined
battery and lithium battery.
Over-discharge delay time; when the battery
Battery over
voltage is lower than the parameter [12], the
13 discharge delay [13] 5S default
inverter output will be turned off after the time
time
set by this parameter is delayed. The setting

Solar charge inverter V2.0 25

 Parameter Parameter
Settings Description
no. name

range is 5S~55S, with a step of 5S. It is valid for

user-defined battery and lithium battery.

Battery undervoltage alarm point; when the

battery voltage is lower than the point, an
Battery under undervoltage alarm is given, and the output is
14 [14] 22V default
voltage alarm not turned off; the setting range is 20V~26V,
with a step of 0.2V. It is valid for user-defined
battery and lithium battery.
Battery discharge limit voltage; when the
Battery battery voltage is lower than the point, the
15 discharge limit [15] 20V default output is turned off immediately; the setting
voltage range is 20V~26V, with a step of 0.2V. It is valid
for user-defined battery and lithium battery.

[16] DIS Equalizing charge is disabled

Battery
16 equalization
Equalizing charge is enabled, only valid for
enable
[16] ENA default vented lead-acid battery and sealed lead-acid
battery
Battery Equalizing charge voltage; setting range:
[17] 29.2V
17 equalization 24V~29.2V, with a step of 0.2V; valid for vented
default
voltage lead-acid battery and sealed lead-acid battery
Equalizing charge time; setting range:
Battery 5min~900min, with a step of 5 minutes; valid
18 [18] 120 default
equalized time for vented lead-acid battery and sealed lead-
acid battery
Equalizing charge delay; setting range:
Battery
5min~900min, with a step of 5 minutes; valid
19 equalized time [19] 120 default
for vented lead-acid battery and sealed lead-
out
acid battery
Battery Equalizing charge derating time, 0~30days,
20 equalization [20] 30 default with a step of 1 day; valid for vented lead-acid
interval battery and sealed lead-acid battery

21 [21] DIS Stop equalizing charge immediately.

Solar charge inverter V2.0 26

 Parameter Parameter
Settings Description
no. name

Battery
equalization [21] ENA default Start equalizing charge immediately.
immediately

[22] DIS default Power saving mode disabled.

After the power saving mode is enabled, if the

Power saving
22 load is null or less than 50W, the inverter
mode
[22] ENA output is turned off after a delay for a certain
period of time. When the load is more than
50W, the inverter automatic restart.
Automatic restart when overload is disabled. If
[23] DIS an overload occurs and the output is turned off,
the machine will not restart.
Restart when Automatic restart when overload is enabled. If
23
over load an overload occurs and the output is turned off,
[23] ENA default the machine will restart after a delay of 3
minutes. After it reaches 5 cumulative times,
the machine will not restart.
Automatic restart when over temperature is
disabled. If an over-temperature shutdown
[24] DIS
occurs, machine will not restart to turn the
Restart when
output on.
24 over
Automatic restart when over temperature is
temperature
enabled. If an over-temperature shutdown
[24] ENA default
occurs, the machine will restart when the
temperature drops.

[25] DIS Alarm is disabled

25 Alarm enable
[25] ENA default Alarm is enabled

Alarm beep is disabled when the status of the

[26] DIS
Beeps while main input source changes
26 primary source
is interrupted Alarm beep is enabled when the status of the
[26] ENA default
main input source changes

Solar charge inverter V2.0 27

 Parameter Parameter
Settings Description
no. name

It is disabled to automatically switch to the

[27] DIS
Mains when the inverter is overloaded.
Bypass output
27
when over load
It is enabled to automatically switch to the
[27] ENA default
Mains when the inverter is overloaded.

S series model：Max AC charger current.

[28] 80A default
Setting range: 0~80A；
Max AC charger
28
current
U series model：Max AC charger current.
[28] 40A default
Setting range: 0~40A；

Supply for industrial frequency transformer

[29] DIS default
(disabled)
29 Split Phase
Supply for industrial frequency transformer
[29] ENA
(enabled)

Battery When the battery voltage is under voltage, the

35 undervoltage [35] 26V default battery voltage needs to recover more than this
recovery point set value before the inverter starts the output
Battery fully After the battery is fully charged, it needs to be
37 charged [37] 26V default lower than this set voltage before it can be
recovery point recharged
U series model：120Vac default.
[38] 120Vac Allow to set to 100Vac/105Vac/110Vac/120Vac.
AC output
default The rated output power will be reduced=
voltage setting
(Power Rate)*(Vset/120)
38 (only can be set
S series model：230Vac default.
in the standby
[38]230Vac Allow to set to 200/208/220/230/240Vac.
mode )
default The rated output power will be reduced=
(Power Rate)*(Vset/230)

Solar charge inverter V2.0 28

 4.3 Battery type parameters

For Lead-acid Battery :

Battery type
Colloidal lead Vented lead
Sealed lead acid User-defined
acid battery acid battery
battery (SLD) (User)
(GEL) (FLD)
Parameters

Overvoltage disconnection voltage 30.0V 30.0V 31.0V 18～30V

Battery fully charged recovery 26V 26V 26V 26V

point(setup item 37) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Equalizing charge voltage 29.2V - 29.6V 18～30V

18～30V
Boost charge voltage 28.8V 28.4V 29.2V
(Adjustable)

18～30V
Floating charge voltage 27.6V 27.6V 27.6V
(Adjustable)

18～30V
Undervoltage alarm voltage(01 fault) 22V 22V 22V
(Adjustable)

Undervoltage alarm voltage recovery

Undervoltage alarm voltage+0.4V
point(01 fault)

Low voltage disconnection voltage(04 18～30V

21.0V 21.0V 21.0V
fault) (Adjustable)

Low voltage disconnection voltage

recovery point (04 fault)(setup item
26V 26V 26V 26V
(Adjustable) (Adjustable) (Adjustable) (Adjustable)
35)

18～30V
Discharge limit voltage 20.0V 20.0V 20.0V
(Adjustable)

1～30s
Over-discharge delay time 5s 5s 5s
(Adjustable)

0～600
Equalizing charge duration 120 minutes - 120 minutes minutes
(Adjustable)

0～250 days
Equalizing charge interval 30 days - 30 days
(Adjustable)

10～600
Boost charge duration 120 minutes 120 minutes 120 minutes minutes
(Adjustable)

Solar charge inverter V2.0 29

 For Lithium Battery :
Ternary Lithium Lithium Lithium
Battery type Ternary
lithium iron iron iron
lithium
battery phosphat phosphat phosphate
battery
(N08) e battery e battery battery
Parameters (N07)
(LF07) (LF08) (LF09)

Overvoltage disconnection voltage 31.6V 33V 30V 30V 33V

Battery fully charged recovery point(setup 27.4V 30.4V 23.2V 26.8V 29.8V
item 37) (Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Equalizing charge voltage

28.8V 31.6V 24.6V 28.4V 31.6V
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Boost charge voltage

28.8V 31.6V 24.6V 28.4V 31.6V
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Floating charge voltage

28.8V 31.6V 24.6V 28.4V 31.6V
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Undervoltage alarm voltage (01 fault)

23.4V 26.8V 21.6V 24.8V 27.8V
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Undervoltage alarm voltage recovery

Undervoltage alarm voltage+0.4V
point(01 fault)

Low voltage disconnection voltage (04 fault)

21.0V 24.0V 21.0V 24.4V 27.0V
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Low voltage disconnection voltage recovery 26V 29.6V 23.8V 27.2V 30.6V
point (04 fault)(setup item 35) (Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Discharge limit voltage 19.6V 22.4V 20.4V 23.2V 26.2V

Over-discharge delay time

30s 30s 30s 30s 30s
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Equalizing charge duration - - - - -

Equalizing charge interval - - - - -

120 120 120 120 120

Boost charge duration minutes minutes minutes minutes minutes
(Adjustable) (Adjustable) (Adjustable) (Adjustable) (Adjustable)

Solar charge inverter V2.0 30

5. Other functions
5.1 Dry node
Working principle: This dry node can control the ON/OFF of the diesel generator to

charge the battery. ① Normally, the terminals are that the NC-N point is closed and

the NO-N point is open; ② When the battery voltage reaches the low voltage

disconnection point, the relay coil is energized, and the terminals turn to that the

NO-N point is closed while NC-N point is open. At this point, NO-N point can drive

resistive loads: 125VAC/1A, 230VAC/1A, 30VDC/1A.

5.2 RS485 communication port

This port is an RS485 communication port ;

This port is an RS485 communication port which comes with two functions:
① It allows direct communication with the optional host computer developed by our
company through this port, and enables monitoring of the equipment running status
and setting of some parameters on the computer;
② It also allows direct connection with the optional RS485 to WiFi/GPRS
communication module developed by our company through this port. After the
module is selected, you can connect the all-in-one solar charge inverter through the
mobile phone WiFi/GPRS APP, on which you can view the operating parameters and
status of the device.

As shown in the figure:

Pin 1 is 5V power supply, Pin 2 is GND, Pin 5 is RS485-A2, Pin 6 is B2,
Pin 7 is RS485-A1,and Pin 8 is RS485-B1 ;

5.3 Can communication function

Function of connecting lithium battery communication

As shown in the figure:

Pin 1 is CAN-L, and Pin 2 is CAN-H

5.4 USB communication port

This is a USB communication port, which can be used for USB communication with

the optional PC host software. To use this port, you should install the

corresponding "USB to serial chip CH340T driver" and APP in the computer.

Solar charge inverter V2.0 31

6. Protection
6.1 Protections provided

No. Protections Description

PV current/power When charging current or power of the PV array configured exceeds

1
limiting protection the PV rated, it will charge at the rated.

At night, the battery is prevented from discharging through the PV

PV night reverse-
2 module because the battery voltage is greater than the voltage of PV
current protection
module.

When the mains voltage exceeds 280V (230V model) or 140V (120V
Mains input over
3 model), the mains charging will be stopped and switched to the
voltage protection
inverter mode.

When the mains voltage is lower than 170V (230V model /UPS mode)
Mains input under
4 or 90V (120V model or APL mode), the mains charging will be
voltage protection
stopped and switched to the inverter mode.

When the battery voltage reaches the overvoltage disconnection

Battery over point, the PV and the mains will be automatically stopped to charge
5
voltage protection the battery to prevent the battery from being overcharged and
damaged.

When the battery voltage reaches the low voltage disconnection

Battery low voltage
6 point, the battery discharging will be automatically stopped to
protection
prevent the battery from being over-discharged and damaged.

Load output short When a short-circuit fault occurs at the load output terminal, the AC
7
circuit protection output is immediately turned off and turned on again after 1 second.

Heat sink over When the internal temperature is too high, the all-in-one machine
8 temperature will stop charging and discharging; when the temperature returns to
protection normal, charging and discharging will resume.

Output again 3 minutes after an overload protection, and turn the

Overload output off after 5 consecutive times of overload protection until the
9
protection machine is re-powered. For the specific overload level and duration,
refer to the technical parameters table in the manual.

Solar charge inverter V2.0 32

 PV reverse polarity
10 When the PV polarity is reversed, the machine will not be damaged.
protection

AC reverse Prevent battery inverter AC current from being reversely input to

11
protection Bypass.

Bypass over current

12 Built-in AC input overcurrent protection circuit breaker.
protection

When the discharge output current of the battery is greater than the
Battery input over
13 maximum value and lasts for 1 minute, the AC input would switched
current protection
to load.

When the battery is reversely connected or the inverter is short-

Battery input
14 circuited, the battery input fuse in the inverter will blow out to
protection
prevent the battery from being damaged or causing a fire.

Charge short When the external battery port is short-circuited in the PV or AC

15
protection charging state, the inverter will protect and stop the output current.

Solar charge inverter V2.0 33

6.2 Fault code meaning
Whether it
Fault code Fault name affects the Description
output or not
【01】 BatVoltLow Yes Battery undervoltage alarm
Battery discharge average current
【02】 BatOverCurrSw Yes
overcurrent software protection

【03】 BatOpen Yes Battery not-connected alarm

【04】 BatLowEod Yes Battery undervoltage stop discharge alarm

【05】 BatOverCurrHw Yes Battery overcurrent hardware protection

【06】 BatOverVolt Yes Charging overvoltage protection

【07】 BusOverVoltHw Yes Bus overvoltage hardware protection

【08】 BusOverVoltSw Yes Bus overvoltage software protection

【09】 PvVoltHigh No PV overvoltage protection

【10】 PvBuckOCSw No Buck overcurrent software protection

【11】 PvBuckOCHw No Buck overcurrent hardware protection

【12】 bLineLoss No Mains power down

【13】 OverloadBypass Yes Bypass overload protection

【14】 OverloadInverter Yes Inverter overload protection

【15】 AcOverCurrHw Yes Inverter overcurrent hardware protection

【17】 InvShort Yes Inverter short circuit protection

【19】 OverTemperMppt No Buck heat sink over temperature protection

Inverter heat sink over temperature

【20】 OverTemperInv Yes
protection

【21】 FanFail Yes Fan failure

【22】 EEPROM Yes Memory failure

【23】 ModelNumErr Yes Model setting error

Inverted AC Output Backfills to Bypass AC

【26】 RlyShort Yes
Input

【29】 BusLow Yes Internal battery boost circuit failure

Solar charge inverter V2.0 34

 6.3 Handling measures for part of faults

Fault
Faults Handling measures
code
Check if the battery air switch or the PV air switch has
Display No display on the screen been closed; if the switch is in the "ON" state; press any
button on the screen to exit the screen sleep mode.

Measure if the battery voltage exceeds rated, and turn off

【06】 Battery overvoltage protection
the PV array air switch and Mains air switch.

Battery undervoltage Charge the battery until it returns to the low voltage
【01】【04】
protection disconnection recovery voltage.

Check if the fan is not turning or blocked by foreign

【21】 Fan failure
object.

When the temperature of the device is cooled below the

Heat sink over temperature
【19】【20】 recovery temperature, normal charge and discharge
protection
control is resumed.

Bypass overload protection, ① Reduce the use of power equipment;

【13】【14】
inverter overload protection ② Restart the unit to resume load output.

① Check the load connection carefully and clear the short-

Inverter short circuit
【17】 circuit fault points;
protection
② Re-power up to resume load output.

Use a multimeter to check if the PV input voltage exceeds

【09】 PV overvoltage
the maximum allowable input voltage rated.

Check if the battery is not connected or if the battery

【03】 Battery missed alarm
circuit breaker is not closed.

Disconnect the AC input,PV input and battery input. After

the screen is off, only connect the battery and start up. If
Inverted AC Output Backfills
【26】 fault 26 is reported, it indicates that the AC input relay
to Bypass AC Input
switch is short-circuited, and you need to contact the
manufacturer to replace it.

Solar charge inverter V2.0 35

7. System maintenance
 In order to maintain the best long-term performance, it is recommended to conduct
following checks twice a year.

1. Make sure that the airflow around the unit is not blocked and remove any dirt or debris from
the heat sink.

2. Check that all exposed wires are damaged by exposure to sunlight, friction with other objects
around them, dryness, bite by insects or rodents, etc., and the wires shall be repaired or
replaced if necessary.

3. Verify for the consistency of indication and display with the operation of the device. Please
pay attention to the display of any faults or errors, and take corrective actions if necessary.

4. Check all wiring terminals for corrosion, insulation damage, signs of high temperature or
burning/discoloration, and tighten the screws.

5. Check for dirt, nesting insects and corrosion, and clean up as required.

6. If the arrester has failed, replace in time to prevent lightning damage to the unit or even other
equipment of the user.

Warning: Danger of electric shock! When doing the above operations, make sure that all power
supplies of the all-in-one machine have been disconnected, and all capacitors have been discharged,
and then check or operate accordingly!

 The company does not assume any liability for damage caused by:

① Improper use or use in improper site.

② Open circuit voltage of the PV module exceeds the maximum allowable voltage rated.

③ Temperature in the operating environment exceeds the limited operating temperature range.

④ Disassemble and repair the all-in-one solar charge inverter without permission.

⑤ Force majeure: Damage that occurs in transportation or handling of the all-in-one solar charge
inverter.

Solar charge inverter V2.0 36

8. Technical parameters
Models HF2430S80-H HF2430U80-H

AC mode

Rated input voltage 220/230Vac 110/120Vac

(170Vac~280Vac) ±2%
Input voltage range (90Vac-140Vac) ±2%
(90Vac-280Vac) ±2%

Frequency 50Hz/ 60Hz (Auto detection)

47±0.3Hz ~ 55±0.3Hz (50Hz);

Frequency Range
57±0.3Hz ~ 65±0.3Hz (60Hz);

Overload/short circuit
Circuit breaker
protection

Efficiency >95%

Conversion time
10ms (typical)
(bypass and inverter)

AC reverse protection Available

Maximum bypass
30A 40A
overload current

Inverter mode

Output voltage
Pure sine wave
waveform
Rated output power
3300 3300
(VA)
Rated output power
3300 3300
(W)

Power factor 1

Rated output voltage

230Vac 120Vac
(Vac)

Output voltage error ±5%

Output frequency 50Hz ± 0.3Hz

range (Hz) 60Hz ± 0.3Hz

Maximum Efficiency >92%

For S model:
(102% < load <125%) ±10%: report error and turn off the output after 5 minutes;
(125% < load < 150%) ± 10%: report error and turn off the output after 10 seconds;
Overload protection
Load >150% ±10%: report error and turn off the output after 5 seconds;
For U model:
(102% < load <110%) ±10%: report error and turn off the output after 5 minutes;

Solar charge inverter V2.0 37

 (110% < load < 125%) ± 10%: report error and turn off the output after 10 seconds;
Load >125% ±10%: report error and turn off the output after 5 seconds;

Peak power 6000VA 6000VA

Loaded motor
2HP 2HP
capability
Rated battery input
24V (Minimum starting voltage 22V)
voltage

Undervoltage alarm/shutdown voltage/overvoltage alarm /overvoltage recovery... settable

Battery voltage range
on LCD screen)

Power saving mode Load ≤50W

AC charging

Battery type Lead acid or lithium battery

Maximum charge
0-80A 0-40A
current(can be set)

Charge current error ± 5Adc

Charge voltage range 20 –33Vdc

Short circuit protection Circuit breaker and blown fuse

Circuit breaker
30A 40A
specifications

Overcharge protection Alarm and turn off charging after 1 minute

PV charging

Maximum PV open
500Vdc
circuit voltage
PV operating voltage
120-500Vdc
range

MPPT voltage range 120-450Vdc

Battery voltage range 20 –33Vdc

Maximum input power 4000W 4000W

PV charging current
0-80A 0-80A
range (can be set)
Charging short circuit
Blown fuse
protection

Wiring protection Reverse polarity protection

Hybrid charging Max charger current specifications (AC charger+PV charger)

Max charger
0-80A 0-80A
current(can be set)

Certified specifications

Certification CE(IEC 62109-1)

Solar charge inverter V2.0 38

EMC certification level EN61000, C2

Operating temperature
-10°C to 55°C
range

Storage temperature
-25°C ~ 60°C
range

Humidity range 5% to 95% (Conformal coating protection)

Noise ≤60dB

Heat dissipation Forced air cooling, variable speed of fan

Communication
USB/CAN/RS485(WiFi/GPRS)/Dry node control
interface

Size (L*W*D) 378mm*280mm*103mm

Weight (kg) 7.4 8

Solar charge inverter V2.0 39