GE Panametrics O.XY IQ Manual

TurkStream Onshore Receiving Terminal
PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

84
Oxygen
oxy.IQ
Panametrics Oxygen Analyzer
User’s Manual
bhge.com 910-296 Rev. D

September 2017
85
86
oxy.IQ
Panametrics Oxygen Analyzer
User’s Manual
910-296 Rev. D
September 2017
bhge.com
© 2017 Baker Hughes, a GE company – All rights reserved.
Baker Hughes reserves the right to make changes in specifications and features shown
herein, or discontinue the product described at any time without notice or obligation.
Contact your BHGE representative for the most current information. The Baker Hughes
logo is a trade mark of Baker Hughes, a GE company. The GE Monogram is a trademark of
the General Electric Company.
87
[no content intended for this page]

ii 88 oxy.IQ User’s Manual
Preface
Product Registration
Thank you for purchasing a model oxy.IQ from GE. Please register your
product at www.gemeasurement.com/productregistration for product support
such as the latest software/firmware upgrades, product information and
special promotions.
Services
GE provides customers with an experienced staff of customer support
personnel ready to respond to technical inquiries, as well as other remote and
on-site support needs. To complement our broad portfolio of industry-leading
solutions, we offer several types of flexible and scalable support services
including: Training, Product Repairs, Extended Warranties, Service
Agreements and more. Please visit www.gemeasurement.com/services for
more details.
Terms and Conditions

GE’s sales Terms and Conditions for your recent purchase of a GE product,
including the applicable product Warranty, can be found on our website at
the following link: www.gemeasurement.com/sales-terms-and-conditions
Typographical Conventions
Note: These paragraphs provide information that provides a deeper
understanding of the situation, but is not essential to the proper
completion of the instructions.
Important : These paragraphs provide information that emphasizes
instructions that are essential to proper setup of the equipment.
Failure to follow these instructions carefully may cause unreliable
performance.
CAUTION! This symbol indicates a risk of potential minor

personal injury and/or severe damage to the equipment, unless
these instructions are followed carefully.
WARNING! This symbol indicates a risk of potential serious

personal injury, unless these instructions are followed
carefully.

oxy.IQ User’s Manual 89 iii
Preface
Safety Issues
WARNING! It is the responsibility of the user to make sure all

local, county, state and national codes, regulations, rules and
laws related to safety and safe operating conditions are met for
each installation.
Attention European Customers! To meet CE Marking

requirements for all units intended for use in the EU, all
electrical cables must be installed as described in this manual.
Auxiliary Equipment
Local Safety Standards
The user must make sure that he operates all auxiliary equipment in
accordance with local codes, standards, regulations, or laws applicable to
safety.
Working Area
WARNING! Auxiliary equipment may have both manual and

automatic modes of operation. As equipment can move
suddenly and without warning, do not enter the work cell of
this equipment during automatic operation, and do not enter
the work envelope of this equipment during manual operation.
If you do, serious injury can result.
WARNING! Make sure that power to the auxiliary equipment

is turned OFF and locked out before you perform maintenance
procedures on this equipment.

iv 90 oxy.IQ User’s Manual
Preface
Qualification of Personnel
Make sure that all personnel have manufacturer-approved training applicable
to the auxiliary equipment.
Personal Safety Equipment

Make sure that operators and maintenance personnel have all safety
equipment applicable to the auxiliary equipment. Examples include safety
glasses, protective headgear, safety shoes, etc.
Unauthorized Operation
Make sure that unauthorized personnel cannot gain access to the operation of
the equipment.

oxy.IQ User’s Manual 91 v
Preface
Regulatory Compliance
Waste Electrical and Electronic Equipment (WEEE) Directive
GE is an active participant in Europe’s Waste Electrical and Electronic
Equipment (WEEE) take-back initiative (Directive 2012/19/EU).
The equipment that you bought has required the extraction and use of natural
resources for its production. It may contain hazardous substances that could
impact health and the environment.
In order to avoid the dissemination of those substances in our environment

and to diminish the pressure on the natural resources, we encourage you to
use the appropriate take-back systems. Those systems will reuse or recycle
most of the materials of your end life equipment in a sound way. The crossed-
out wheeled bin symbol invites you to use those systems.
If you need more information on the collection, reuse and recycling systems,
please contact your local or regional waste administration. Visit
http://www.gemeasurement.com/environmental-health-safety-ehs for take-
back instructions and more information about this initiative.
RoHS
The oxy.IQ fully complies with RoHS regulations (Directive 2011/65/EU).

vi 92 oxy.IQ User’s Manual
Contents
Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Terms and Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Safety Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Auxiliary Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Chapter 1. Features and Capabilities
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 Hazardous Location Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.5 Sample Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Chapter 2. Installation
2.1 Mounting the oxy.IQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Wiring the oxy.IQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.2.1 Longer Cable Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.3 Installing an Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 3. Initial Setup & Operation
3.1 The oxy.IQ Display and Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2 The oxy.IQ Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3 Adjusting and Calibrating the oxy.IQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3.1 Selecting the Output Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3.2 Trimming the Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.3.3 Air Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3.4 Span Gas Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter 4. User Programming
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2 The Calibration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.1 Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.2 Span Gas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.2.3 Sensor Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.3 The Display Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3.1 Select the O2 Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.3.2 Display the Sensor Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

oxy.IQ User’s Manual 93 vii
Contents
4.3.3 Adjust the Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.4 The Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.4.1 Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.4.2 Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.4.3 Error Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
4.4.4 Error Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 5. The Service Menu
5.1 Menu Map & Service Passcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.2 Entering the Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.2.1 Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chapter 6. Specifications
6.1 Intrinsically Safe (IS) Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.2 Non-Incendive (Div 2) and General Purpose Installation. . . . . . . . . . . . . . . . 31
6.3 All Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6.4 Product Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix A. Outline and Installation Drawings . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix B. Menu Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Appendix C. Order String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Appendix D. Certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
D.1 ATEX EU-Type Examination Certificate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
D.2 ATEX IECEx MAM Ex Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
D.3 Canadian Certificate of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
D.4 FM Certificate of Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
D.5 IECEx Certificate of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Addendum A. oxy.IQ Safety Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

viii 94 oxy.IQ User’s Manual

1.1 Introduction
The oxy.IQ Panametrics Oxygen Transmitter (see Figure 1 below) is a
highly reliable and cost-effective two-wire, loop-powered transmitter
with a linearized 4 to 20 mA output. It measures oxygen content in ten
ppm ranges (10, 20, 50, 100, 200, 500, 1000, 2000, 5000 and 10000 ppm)
and eight percentage ranges (1, 2, 5, 10, 21, 25, 50 and 100%). All ranges
are user-selectable. This compact transmitter uses proven sensor
technology to accurately measure oxygen content in a variety of gases,
even in hazardous (classified) locations.
Figure 1: oxy.IQ

oxy.IQ User’s Manual 95 1
1.2 Hazardous Location Certifications

When equipped with an optional Zener barrier or galvanic isolator, the
oxy.IQ can be mounted in a hazardous (classified) location. The oxy.IQ
with Intrinsically Safe option is certified to USA, Canadian, ATEX, and
international IECEx IS requirements. The standard oxy.IQ is certified
to USA, Canadian, EU ATEX and International IECEx Div2/Zone 2
Non-Incendive requirements.
1.3 Applications
Some typical applications for the oxy.IQ Panametrics oxygen
transmitter include the following:
• Glove box purge and leak detection
• Natural gas
• Semiconductor wafer machines
• Coating process machines
• Membrane air separators
• Inert welding gases
• Pure gaseous hydrocarbon streams
• Process monitoring of gaseous monomers
• Heat treating and bright annealing

2 96 oxy.IQ User’s Manual
1.4 Features
The oxy.IQ oxygen sensor uses an advanced galvanic fuel cell that
provides superior performance, accuracy, stability and long life. The
cell’s innovative design eliminates the potential for negative signal
output and reduces sources of contamination.
The cell is unaffected by other background gases or hydrocarbons and
is compatible with acidic gases (OX-2 and OX-4 cells). Recovery from
air at low ppm levels takes just a few minutes. Because the cell is
self-contained, minimal maintenance is required. There is no
electrolyte to change and no electrodes to clean.
The oxy.IQ offers the following features:
• Two-wire, loop-powered, 4 to 20 mA transmitter
• Display with keypad
• Intrinsically-safe option
• Proven galvanic fuel cell O2 sensor technology
• User-selectable ranges for ppm and percent oxygen
• User-friendly and intuitive user interface with diagnostics
• Microprocessor-based, all-digital technology for reliable

operation
• Low maintenance, economical and compact
• Sensor failure output error
• Sensor lifetime indication
• NAMUR error indication

1.5 Sample Systems

In addition to the standard features and options, GE offers a full line of
sample handling systems for a variety of applications. If needed, GE
can design and build a sample conditioning system to meet unique
application requirements. Please contact GE for details.
Table 1 below lists some background gases that can interfere with the
oxygen sensor.
Table 1: Oxygen Sensor Interference Gases

OX-1 & 5 ppm OX-2 ppm OX-3 % OX-4 %
Gas Cont. Cont. Cont. Int. (1) Cont. Int.
H2S <5 ppm <10 ppm 0.0005 % 0.01 % 0.001 % 0.1 %
SO3 <10 ppm <10 ppm 0.01 % 0.1 % 0.01 % 0.1 %
SO2 <10 ppm (3) 0.01 % 0.1 % (3) (3)
HCl <1000 ppm (3) 0.1 % 1.0 % (3) (3)
HCN <1000 ppm (3) 0.1 % 1.0 % (3) (3)
CO2 <1000 ppm (3) 0.1 % 20 & (3) (3)
NO2 (2) (2) (2) (2) (2) (2)
Cl2 (2) (2) (2) (2) (2) (2)
Cont. = Continuous, Int. = Intermittent
(1) Recommended maximum exposure 30 minutes, followed by flushing
with ambient air for an equal period.
(2) Minimal effect on sensor performance, but produces signal interference
of 1:2 ratio for ppm levels only (e.g., 100 ppm NO2 looks like 200 ppm O2).
(3) Minimal effect on sensor performance

2.1 Mounting the oxy.IQ
To install the oxy.IQ into the process or sample system, refer to
Figure 9 on page 38 and/or Figure 2 below and proceed to the next
page.
CONNECTOR
2.05
1.58
Note: All dimensions are inches [mm]. [52.1]
[40.3]
B 2.75
[69.8] C
4.10
[104.2]
0.32
1.33 [8.25]
[33.9]
2X 2X 1.03 A
1/8-27NPT-2B 8-32 UNC-2B [26.27]
.27 [6.9] .51 [12.9] MAX
0.53
[13.57]
1.00
[25.40]
Ø1.75
[44.3]
Figure 2: Outline and Dimensions (ref. dwg. 712-1840)
Note: To avoid collecting condensate that may damage the oxygen

sensor, mount the oxy.IQ in an upright position, with the sensor
manifold below the electronics module.

2.1 Mounting the oxy.IQ (cont.)

Install the oxy.IQ by completing the following steps:
1. Remove the oxy.IQ and the separately-packaged oxygen sensor
(see Figure 3 below) from the shipping container. Keep the
shipping container and packaging material for possible future
use.
IMPORTANT: DO NOT open the oxygen sensor package until you are
ready to install the sensor.
Figure 3: Packaged Oxygen Sensor
2. Remove the sensor manifold by unscrewing it from the blue

knurled nut on the sensor base at the bottom of the electronics
module.

2.1 Mounting the oxy.IQ (cont.)

IMPORTANT: The maximum operating pressure for the oxy.IQ is 10 psi,
and the burst pressure of the unit is 200 psi. Be sure the
sample conditioning system is designed to maintain the
oxy.IQ pressure below these limits, and that the oxy.IQ
outlet is vented to atmosphere during operation and
calibration.
3. Using PTFE tape as a sealant, connect the sample gas inlet and
outlet to the 1/8” NPT ports on the sensor manifold (see Figure 4
below). Either port may be used as the inlet or the outlet, as the
direction of flow does not matter.
Sensor Manifold
PTFE Tape
Sample Inlet Sample Outlet

Figure 4: Sensor Manifold Installation

2.2 Wiring the oxy.IQ

To wire the oxy.IQ, refer to Figure 14 on page 43, then proceed as
follows:
WARNING! For IS (Intrinsically Safe) applications, the oxy.IQ

must be installed with a Zener barrier (see the
top of Figure 14 on page 43). Also, for
installations in a hazardous location, the blue IS
cable (p/n 704-1318-02, 10) must be used.
1. Attach the appropriate cable to the oxy.IQ (see Figure 5 below). Be

sure to align the white arrow on the cable connector with the
white arrow on the oxy.IQ connector, and then push the top of the
cable connector straight down onto the mating connector on the
rear of the electronics module until you hear it click into place.
IMPORTANT: Do not rotate the cable connector during installation (it is
not threaded) and do not hold the connector by its bottom
section while pushing it down into place.
IMPORTANT: To remove the cable, grasp the bottom section of the
connector (the part with the white arrow) and pull it
straight up until the cable comes loose. DO NOT twist the
connector either by hand or with any tool during removal.
Blank Label
Std. Cable
Cable Connector Alignment Arrow
Figure 5: oxy.IQ Cable and Connector

2.2 Wiring the oxy.IQ (cont.)

2. Connect the flying lead end of the cable as shown in the wiring
diagram, according to one of the following conditions:
• No Zener Barrier or Galvanic Isolator:
For use in non-hazardous areas or Div 2 hazardous areas.
• With Zener Barrier or Galvanic Isolator:
Required for use in hazardous areas.
IMPORTANT: To remove the cable from the oxy.IQ electronics module,

simply pull straight up on the lower section of the cable
connector as close to the oxy.IQ body as possible. Do not
pull on the cable or the upper portion of the cable
connector, and do not try to unscrew the cable connector.
2.2.1 Longer Cable Lengths
GE offers cables in 2 m and 10 m standard lengths. Longer cable
lengths may be used with the oxy.IQ, but these are not available from
GE. If you require a longer cable, refer to the following figures for the
required cable specifications and construct your own cable for splicing
onto the standard GE cable:
• Standard Cable: Figure 10 on page 39 and Figure 11 on page 40
• IS Cable: Figure 12 on page 41 and Figure 13 on page 42

2.3 Installing an Oxygen Sensor

To install a new or replacement oxygen sensor in the oxy.IQ, refer to
Figure 6 below and complete the following steps:
Sensor Base
Knurled Nut
Oxygen Sensor Ring
Sensor Manifold
Figure 6: Oxygen Sensor Installation
1. Disconnect the power from the oxy.IQ.

2. Loosen the blue knurled nut and remove the oxy.IQ electronics
module from the sensor manifold. If a previous oxygen sensor is
already in place, remove and discard it.

2.3 Installing an Oxygen Sensor (cont.)

3. Apply power to the unit. The screen will display “INITIALIZING PLEASE
WAIT” for a few seconds before it begins to display measurement
data.
Note: Before continuing with the installation, become familiar with the
procedures for programming and calibrating the oxy.IQ discussed
in Chapter 3, Initial Setup & Operation.
4. Trim the 4-20 mA analog output and set the range to 0-25%
oxygen.
5. Open the airtight package (see Figure 3 on page 6) and remove the
oxygen sensor from the package. To maintain the oxygen sensor’s
energy level, remove the red grounding tab and immediately install
the sensor in the oxy.IQ
6. Orient the sensor so that its gold-plated electrodes are facing the
spring-loaded contact pins in the sensor base (see Figure 6 on
page 10). Firmly press the oxygen sensor into the sensor base at
the bottom of the oxy.IQ electronics module.
7. Perform an air calibration on the new oxygen sensor at this time.
On the 0-25% oxygen scale, a properly calibrated oxygen sensor
shows a reading of 20.9% on the display and generates a current of
17.4 mA at the 4-20 mA analog output terminals.
8. Using the blue knurled nut, attach the oxy.IQ electronics module
with the calibrated oxygen sensor to the sensor manifold. Rotate
the display as desired and then hand-tighten the blue knurled nut.
IMPORTANT: Make sure that the O-ring on the top of the sensor
manifold is in place and undamaged. If necessary, contact
GE for a replacement.

2.3 Installing an Oxygen Sensor (cont.)

9. Begin the flow of the process gas. The analog output reading will
drop as the oxygen sensor adjusts to the reduced oxygen level.
During this time, reset the range as required.
10. For improved accuracy in the ppm oxygen ranges, a span gas
calibration should now be performed (see “Span Gas Calibration”
on page 19).
IMPORTANT: Sensor life is dependent on the application. High oxygen

concentrations and contaminants such as acidic gases
will shorten the sensor life.


3.1 The oxy.IQ Display and Keypad
All programming of the oxy.IQ is done via the front panel keypad and
display, as illustrated below.
Display
Down Arrow
Up Arrow
Cancel Enter
Figure 7: oxy.IQ Display and Keypad
The front panel components perform the following functions:

• Display - Data measurements and the programming menus and
options are shown on the LCD display screen.
• Enter - While in measurement mode, press this key to enter

the Main Menu. While in the Main Menu, press this key to save
an entry and advance to the next screen.
• Cancel - While in the Main Menu, press this key to cancel an

entry and to return to the previous screen.
• and Keys - In the Main Menu, use these keys to move the
cursor between rows one row at a time in the direction
indicated.

3.2 The oxy.IQ Menu Map

As an aid in navigating through the Main Menu, a complete Menu Map
of the user program is shown in Figure 16 on page 46. Refer to this
figure as needed while programming the oxy.IQ.
The oxy.IQ Main Menu consists of the following submenus:
• Calibration Menu (no passcode required)
• Display Menu (no passcode required)
• Output Menu (no passcode required)
• Service Menu (factory service passcode required)
To enter the Main Menu from normal display mode, simply press the
Enter key at any time. To leave the Main Menu and return to
measurement mode, press the Cancel key.
Note: Depending on how deep you are in the menu structure, it may be
necessary to press the Cancel key more than once to return all
the way back to measurement mode.
3.3 Adjusting and Calibrating the oxy.IQ

Upon startup, the following five-step adjustment and calibration
procedure must be performed on the oxy.IQ:
1. Select the desired output range.
2. Trim the low (4 mA) and high (20 mA) analog outputs.
3. Upon installation of a new oxygen sensor, calibrate the unit with
air for either a ppm or % sensor.
4. For ppm sensors only, purge the sensor with a low ppm oxygen
gas.
5. For all subsequent calibrations, use a span gas that is appropriate
for the sensor and range selected.

3.3.1 Selecting the Output Range

To select the desired measurement range, complete the following
steps:
1. Press the Enter key to enter the Main Menu.
2. Press the key twice and then press the Enter key to enter
the Output menu.
3. Press the Enter key to select the Range menu option.
4. Use the and keys to scroll through the available options, as

listed in Table 2 below.
Table 2: Available Output Ranges

Units Span Value
% O2 1, 2, 5, 10, 21, 25, 50, 100
ppm O2 10, 20, 50, 100, 200, 500, 1000, 2000, 5000, 10000
5. After selecting the desired output range, press the Enter key to
save the selection. Then, press the Cancel key to return to the
Output menu.

3.3.2 Trimming the Analog Output

To trim the analog output, calibrate the low (4 mA) end of the output
then the high (20 mA) end of the output.
IMPORTANT: The 4 mA and 20 mA adjustments interact with each
other. Therefore, recheck the trim after the procedure has
been completed.
3.3.2a Preparing to Trim the Analog Output
Prepare to trim the analog output as follows:
1. Connect an ammeter in series with the positive oxy.IQ power
supply lead, to monitor the analog output current.
the Output menu.
4. Press the key and then press the Enter key to enter the Trim
menu.
3.3.2b Trimming the Analog Output Low (4 mA) End
1. Press the Enter key to enter the 4 mA Trim menu, and the
analog output is driven to about 4 mA.
2. Use the and keys to adjust the analog output up or down,

until it equals 4.00 ± 0.01 mA.
3. Press the Enter key to save the trim adjustment and return to
the Trim menu.

3.3.2c Trimming the Analog Output High (20 mA) End
1. Press the key and then press the Enter key to enter the 20
mA Trim menu, and the analog output is driven to about 20 mA.
2. Use the and keys to adjust the analog output up or down,

until it equals 20.00 ± 0.01 mA.
3. Press the Enter key to save the trim adjustment and return to
the Trim menu.
3.3.2d Completing the Trim Procedure

1. Repeat both the low (4 mA) end and high (20 mA) end analog
output trimming steps until no further trimming adjustments are
required.
2. Press the Cancel key twice to return to the Main Menu.
3.3.3 Air Calibration

An air calibration is always recommended upon installation of a new
oxygen sensor. However, because of the non-linearity of the oxygen
sensor, a span gas calibration (see the next section) can also be
performed to ensure a faster and more accurate calibration for the
ppm ranges.
CAUTION! The useful life of ppm sensors is extended by

minimizing exposure of the sensor to air.
To perform an air calibration, complete the following steps:
2. Press the Enter key to enter the Calibration menu.
3. Press the Enter key to select the Air menu option.

4. Proceed to the appropriate section, depending on whether you are
calibrating a new sensor or recalibrating an existing sensor.

3.3.3a Calibrating a New Sensor

For a new sensor, continue the air calibration procedure as follows:
1. Press the key and then press the Enter key to select the YES
menu option.
2. Press the Enter key to acknowledge that you are resetting the
sensor lifetime clock.
3. As instructed, remove the sensor manifold to expose the new
oxygen sensor to ambient air for about two minutes. Then, press
the Enter key to continue.
4. A message indicating that the calibration is in progress will be
displayed, and then the calibration data will be shown. At that
time, press the Enter key to save the calibration data and return
to measurement mode.
Note: A second calibration of the new sensor should be performed
within 1-2 days of the first calibration.
3.3.3b Recalibrating an Existing Sensor

For an existing sensor, continue the air calibration procedure as
follows:
1. Press the Enter key to select the NO menu option.

2. As instructed, remove the sensor manifold to expose the oxygen
sensor to ambient air for about two minutes. Then, press the
Enter key to continue.
3. A message indicating that the calibration is in progress will be
displayed, and then the calibration data will be shown. At that
time, press the Enter key to save the calibration data and return
to measurement mode.

3.3.4 Span Gas Calibration

Before beginning the span gas calibration, make sure the oxy.IQ is
indicating an O2 level less than the span gas value, to ensure an
accurate calibration. Then, start the flow of the span gas to the sensor.
For accurate calibration, the span gas should have an oxygen content
of 70-90% of the range being calibrated.
To perform the span calibration, complete the following steps:
1. Use the equation below to calculate the expected mA output that
corresponds to the known oxygen content of the span gas:
Span Gas ppm

4.0 + 16.0 u -------------------------------------- = mA Output
Full Range ppm
For example, if the span gas contains 80 ppm oxygen and the
0-100 ppm range is being calibrated, the analog output should equal
4 + 16 x (80/100) = 16.8 mA.
2. If you have not done so already, start the flow of span gas to the
sensor and allow both the 4-20 mA output reading and the display
reading to stabilize.
3. After the reading has stabilized, press the Enter key to enter the
Main Menu.
5. Press the key and then press the Enter key to select the
Span Gas menu option.
6. Press the and keys until the measurement agrees with the
span calibration gas value.
7. Confirm that the reading on the display has stabilized, and press
the
Enter key to save the calibration. Then, press the Cancel key
twice to return to measurement mode.



4.1 Introduction
IMPORTANT: The oxy.IQ Service menu is for use by qualified service
personnel only and requires a special passcode for access.
That menu is not discussed in this chapter.
This chapter provides instructions for programming all of the oxy.IQ
menu options available to the user, which can be accessed without the
use of a passcode. These menu options are found in the following Main
Menu submenus:
• Calibration Menu
• Display Menu
• Output Menu
While programming these menus, refer to the menu map in Figure 16
on page 46.
Note: The menu options for initial setup are described in Chapter 3,
Initial Setup & Operation, and are only referenced in this chapter.
4.2 The Calibration Menu

Proceed to the appropriate section to program the desired menu
option.
4.2.1 Air
See “Air Calibration” on page 17.
4.2.2 Span Gas
See “Span Gas Calibration” on page 19.

4.2.3 Sensor Life

To read the sensor life, complete the following steps:
3. Press the key three times and then press the Enter key to
enter the Sensor Life menu.
4. The number of days your sensor has been in use is displayed.
When you have finished reading the information, press the
Enter key to return to the Calibration menu.
5. Press the Cancel key twice to return to measurement mode.

4.3 The Display Menu

option.
4.3.1 Select the O2 Parameter
To select the O2 parameter for display, complete the following steps:
2. Press the key once and then press the Enter key to enter the
Display menu.
3. Press the Enter key to enter the O2 menu.
4. Use the and keys to select the desired O2 range to be

displayed:
• ppm only
• % only
• Auto Select (automatically displays the appropriate range)
5. Press the Enter key to confirm your choice and return to

measurement mode.

4.3.2 Display the Sensor Range

To select whether or not the O2 range of the installed sensor is
displayed, complete the following steps:
Display menu.
Display Range menu.
4. Use the and keys to select the desired option:

• On - the O2 range is displayed at the bottom of the screen
• Off - the O2 range is not displayed at the bottom of the screen
5. Press the Enter key to confirm your choice and return to

measurement mode.
4.3.3 Adjust the Contrast

To adjust the display contrast, complete the following steps:
the Contrast menu.
3. Use the and keys to adjust the contrast to the desired value,
then press the Enter key to save the new value.

4.4 The Output Menu

option.
4.4.1 Range
See “Selecting the Output Range” on page 15.
4.4.2 Trim
See “Trimming the Analog Output” on page 16.
4.4.3 Error Type
To select the process conditions that will activate an on-screen
warning and send an alarm to the analog output device, complete the
following steps:
the Output menu.
the Error Type menu.

4.4.3 Error Type (cont.)
4. Use the and keys to select the desired option and then press
the Enter key to activate that error type. A check mark will
appear next to the selected option to indicate that it is activated.
The following options are available, and you may activate as many
of these options as you wish.
Note: Only the first four options are displayed on the screen upon
entering this menu. When you scroll down to the fourth option
(Low Temp), a down arrow to the right of this option indicates that
an additional screen of options is available.
• High O2
• Low O2 (programmable)
• High Temp
• Low Temp (programmable)
• Temp Comp (listed on second screen of options)
Note: Pressing the Enter key on an error type that has already been
activated, will deactivate that option and remove the check mark.
5. Press the Cancel key three times to return to measurement

mode.

4.4.4 Error Output

To select the desired output value that will be sent to the analog output
device upon an error, complete the following steps:
the Output menu.
enter the Error Output menu.
4. Use the and keys to select the desired option and then press
the Enter key to activate that error output. A check mark will
appear next to the selected option to indicate that it is activated.
The following options are available, and you may activate only one
option at a time.
Note: Only the first four options are displayed on the screen upon
entering this menu. When you scroll down to the fourth option
(NAMUR), a down arrow to the right of this option indicates that
an additional screen of options is available.
• None (no error output is generated)
• Low (an output below 4 mA is generated)
• High (an output above 20 mA is generated)
• Value (an error output at a programmable fixed value is

generated)
• NAMUR (listed on second screen of options)
Note: Pressing the Enter key on a different error output will

automatically deselect any previously selected output.
5. Press the Cancel key three times to return to measurement

mode.


CAUTION! The Service Menu is intended for use by

qualified service personnel only, and access to this menu
requires entry of the service passcode. Misuse of the
information in this menu may significantly impair the
accuracy and performance of your oxy.IQ and may cause
it to fail to meet its published specifications.
5.1 Menu Map & Service Passcode

For help in navigating through the Service Menu, refer to the menu
map shown in Figure 17 on page 47. The service passcode required for
access to the oxy.IQ Service Menu is:
7378
5.2 Entering the Service Menu

To enter the Service Menu, complete the following steps:
select the Service menu.
3. Use the and keys to increment or decrement the displayed

value (default = 5000) to enter the service passcode, and then press
the Enter key to access the Service menu.
Note: When entering the passcode, press and release an arrow key to
change the value one digit at a time, or press and hold an arrow
key to change the value at an accelerating rate.
4. Proceed to the appropriate section for the desired menu option.

5.2.1 Diagnostics
To enter the Diagnostics menu option from the Service Menu, complete
the following steps:
1. Use the and keys as necessary to highlight the Diagnostics

menu option.
2. Press the Enter key to enter the Diagnostics menu.

3. Page 1 of the Diagnostics option displays the current values for the
following parameters:
• O2 PA
• Output mA
• Output %
When you have finished reading the information, press the Enter
key to move to Page 2 of the Diagnostics menu or press the Cancel
key to exit the Diagnostics menu.
4. Page 2 of the Diagnostics option displays the current values for the
following parameters:
• Temp °C
• Temp Res
• Gain
• OX-n (currently installed sensor type, n = 1, 2, 3 or 4)
When you have finished reading the information, press the Enter
key to move to Page 1 of the Diagnostics menu or press the Cancel
key to exit the Diagnostics menu.

6.1 Intrinsically Safe (IS) Installation
Intrinsically safe installations require an MTL7706 zener barrier,
one IS cable, and one non-IS cable.
Power Requirements
24 to 28 VDC at 50 mA
Cable
p/n 704-1318-02 (2 m length) or p/n 704-1317-10 (10 m length)
blue jacketed, twisted-pair with connector, 26 AWG conductors,
with connector
Output
Total load must equal 250 : ±5% when using a zener barrier
6.2 Non-Incendive (Div 2) and General Purpose Installation
No zener barrier or galvanic isolator is used.
Power Requirements
9 to 28 VDC, loop-powered, 0.7 W max
Cable
p/n 704-1317-02 (2 m length) or p/n 704-1317-10 (10 m length)
black jacketed, twisted-pair with connector, 26 AWG conductors,
with connector

6.3 All Installations

Process Wetted Materials
SS process unit: 316 stainless steel, Viton® O-ring, gold-plated sensor
electrical contacts, and glass
User-Selectable Measurement Ranges

• PPM sensors:
- 0 to 10 ppmv O2 (OX-1 or OX-2 only)
- 0 to 100 ppmv O2
- 0 to 200 ppmv O2
- 0 to 500 ppmv O2
- 0 to 1000 ppmv O2
- 0 to 2000 ppmv O2
- 0 to 5000 ppmv O2
- 0 to 10,000 ppmv O2
• Percent sensors:
- 0% to 1% O2
- 0% to 2% O2
- 0% to 5% O2
- 0% to 10% O2
- 0% to 25% O2
- 0% to 50% O2
Accuracy
• ±1% of range at calibration point
• ±2% of range at the calibration point for the

0 to 10 ppmv O2 range (OX-1, 2)

6.3 All Installations (cont.)

Repeatability
• ±1% of range
• ±2% of range for the 0 to 10 ppmv O2 range (OX-1, 2)
Resolution
±0.1% of range
Linearity
• ±2% of range (OX-1, 2, 3, 5)
• ±5% of range (OX-4)
O2 Sensor Operating Temperature

32°F to 113°F (0°C to 45°C)
Sample Pressure
Vented to atmosphere during operation and calibration
Atmospheric Pressure Effect

±0.13% of reading per mmHg (directly proportional to absolute
pressure)
Note: During calibration, pressure and flow must be kept constant.
Process Connections
1/8” NPT-F inlet and outlet
Dimensions
4.10 x 2.75 x 2.05 in. (104.1 x 69.9 x 52.1 mm)
Weight
1.35 lb (612 grams)

6.3 All Installations (cont.)

Sample Flow Rate
1.0 SCFH (500 cc/min) recommended for process units
Electrical Classification
Intrinsically Safe package with zener barrier or galvanic isolator:
• USA/Canada:
IS for Class I, Div 1, Groups A, B, C, D; T4
IS for Class I, Zone 0, AEx ia IIC T4; Tamb -20 to +60°C
• EU ATEX:
II 1 G ia IIC Ga
IECEx Ex ia IIC T4; Tamb -20 to +60°C
Intrinsically safe package for non-incendive (Div 2) application without
use of zener barrier or galvanic isolator:
• USA/Canada:
Class I, Div. 2, Groups A, B, C, D; T4
• ATEX/IECEx:
Ex na IIC T4
European Compliance
See the EU Declaration of Conformity at the back of this manual

6.4 Product Label

A typical product label is shown in Figure 8 below:
II 1 G
Figure 8: oxy.IQ Label - IS Package Option


Appendix A. Outline and Installation Drawings

This appendix includes the following oxy.IQ drawings:
• “Outline & Installation (ref. dwg. 712-1840)” on page 38
• “Cable, Standard (ref. dwg. 704-1317, SH 1 of 2)” on page 39
• “Cable, Standard (ref. dwg. 704-1317, SH 2 of 2)” on page 40
• “Cable, IS (ref. dwg. 704-1318, SH 1 of 2)” on page 41
• “Cable, IS (ref. dwg. 704-1318, SH 2 of 2)” on page 42
• “Wiring Options (ref. dwgs. 702-285 & 702-286)” on page 43
• “Schematic Diagram (ref. dwg. 752-347)” on page 44

[13.57]
0.53
[26.27]
1.03
[25.40]
C
1.00
[52.1]
[33.9]
2.05
1.33
[69.8]
2.75
CONNECTOR
A B C
[104.2]
[40.3]
4.10
1.58
.51 [12.9] MAX

8-32 UNC-2B
Ø1.75
[44.3]
B
2X
Ø .03 [.76]
C
Figure 9: Outline & Installation (ref. dwg. 712-1840)

CCORDANCE WITH ANSI Y14.5 (M-1994)
REE OF BURRS AND SHARP EDGES
TION
C
URE RANGE -25°C TO 85°C
oxy.IQ User’s Manual

EETS NEMA 1,3,4,6P AND IEC IP67
IN. PERPENDICULAR & NORMAL
BE TESTED 100% FOR CONTINUITY AND SHORTS.
CABLE LENGTH
K SHELL TIGHTENING FIXTURE SHOWN ON SHEET 2.
CS: 1,2 XX-CABLE LENGTH PART NUMBER
EXTENSION
2 METERS -0/+.1 (6.56FT -0/+.33)
10 METERS -0/+.5 (32.81FT -0/+1.58)
END “A”
BLUE
BROWN
ITEM NO. PART DESCRIPTION

NUMBER
PUSH-PULL CONNECTOR, PLUG, HIROSE
CABLE, BLACK JACKET, 4 X 1 INSULATED 26 AWG CONDUC
SUP SLEEVING, SHRINK, 1/4” BLACK
FERRITE, CABLE CLAMP
INDICATOR ARROW
Figure 10: Cable, Standard (ref. dwg. 704-1317, SH 1 of 2)

133
39
40
.250±.020 NOTES:
1. CUT CABLE TO DESIRED LENGTH ACCORDING TO LENGTH TABLE SHOWN.

2. CUT PRIMARIES & DRAIN EXCLUDING BROWN & BLUE BACK TO JACKET AS SHOWN.
3. STRIP & TIN WIRES USING LEAD FREE SOLDER AT END “B”, BLUE & BROWN, TO LENGTH OF .250”
4. STRIP & TIN WIRES USING LEAD FREE SOLDER AT END “A”, 4 PRIMARIES & DRAIN, TO A LENGTH O
& TINNED WIRE CONDUCTORS NOT TO EXCEED .020”.
25 END “B” 5. INSERT INSULATOR BODY OVER THE SOLDER TERMINATION FIXTURE.
6. INSERT PRE-SOLDERED CONDUCTORS, ITEMS 1-5, IN THE CONTACT SOLDERING POT
AND SOLDER (IRON TEMPERATURE 280°C ± 10°C) USING LEAD FREE SOLDER
IN THEIR RESPECTIVE NUMERICAL LOCATION ACCORDING TO THE COLOR LEGEND.
7. INSPECT SOLDER TERMINATIONS ON END ‘A” AND TRIM ANY LOOSE STRANDS & ELIMINATE
ANY SOLDER BRIDGING.
8. PUSH COMPONENTS DOWN AND TIGHTEN BACK SHELL USING HIROSE FIXTURE SHOWN.
1 TO PREVENT ACCIDENTAL LOOSENING OF THE BACK SHELL PLACE A SMALL AMOUNT OF PRIM
DETAIL B
(LOCTITE 7649) AND ADHESIVE (LOCTITE 271) IN THREADS. TORQUE TO 0.5 N-m.
SCALE 2 : 1
BACK SHELL
WIRE COLOR TO LOCA

HIROSE
R P/N HR30-6P-T02 CABLE LENGTH 1=BROWN, PVC 26 A
2=WHITE, PVC, 26 AW
PLASTIC PART NUMBER
XX-CABLE LENGTH EXTENSION 3=BLUE, PVC, 26 AW

COMPRESSION 2 METERS (6.56FT) 02 4=BLACK, PVC, 26 AW
FITTING .195±.020
10 METERS (32.81FT) 10 5=DRAIN, PVC, 26 AW
6=EMPTY
.100±.020
END “A”
DETAIL C
PLUG INSULATOR BODY
SCALE 2 : 1
SECTION A-
SCALE 4 :
OSE SOLDER FIXTURE
Figure 11: Cable, Standard (ref. dwg. 704-1317, SH 2 of 2)

N HR30-6P-6S-T01

134
N ACCORDANCE WITH ANSI Y14.5 (M-1994).
D FREE OF BURRS AND SHARP EDGES.
FICATION:
0A
VDC

RATURE RANGE -25°C TO 85°C
S MEETS NEMA 1,3,4,6P AND IEC IP67
S. MIN. PERPENDICULAR & NORMAL CABLE LENGTH
LL BE TESTED 100% FOR CONTINUITY AND SHORTS.
K SHELL TIGHTENING FIXTURE SHOWN ON SHEET 2. XX-CABLE LENGTH PART NUMBER
EXTENSION
STICS: 1,2 2 METERS -0/+.1 (6.56FT -0/+.33) 02
10 METERS -0/+.5 (6.56FT -0/+1.58) 10
END “A”
XX
BLUE
135
BROWN
4.00 .25±.03
1.16
2.50
PART
ITEM NO. NUMBER DESCRIPTION
1 214-1060 PUSH-PULL CONNECTOR, PLUG, HIROSE
2 231-132 CABLE, BLUE JACKET, 4 X 1 INSULATED 26 AWG CONDUCT
3 410-064 SUP SLEEVING, SHRINK, 1/4” BLACK
4 222-036 FERRITE, CABLE CLAMP
INDICATOR ARROW
Figure 12: Cable, IS (ref. dwg. 704-1318, SH 1 of 2)

41
42
.250±.020 NOTES:
1. CUT CABLE TO DESIRED LENGTH ACCORDING TO LENGTH TABLE SHOWN.

2. CUT PRIMARIES & DRAIN EXCLUDING BROWN & BLUE BACK TO JACKET AS SHOWN.
3. STRIP & TIN WIRES USING LEAD FREE SOLDER AT END “B”, BLUE & BROWN, TO LENGTH OF
4. STRIP & TIN WIRES USING LEAD FREE SOLDER AT END “A”, 4 PRIMARIES & DRAIN, TO A LEN
& TINNED WIRE CONDUCTORS NOT TO EXCEED .020”.
25 END “B” 5. INSERT INSULATOR BODY OVER THE SOLDER TERMINATION FIXTURE.
6. INSERT PRE-SOLDERED CONDUCTORS, ITEMS 1-5, IN THE CONTACT SOLDERING POT
AND SOLDER (IRON TEMPERATURE 280°C ± 10°C) USING LEAD FREE SOLDER
IN THEIR RESPECTIVE NUMERICAL LOCATION ACCORDING TO THE COLOR LEGEND.
7. INSPECT SOLDER TERMINATIONS ON END ‘A” AND TRIM ANY LOOSE STRANDS & ELIMINAT
ANY SOLDER BRIDGING.
8. PUSH COMPONENTS DOWN AND TIGHTEN BACK SHELL USING HIROSE FIXTURE SHOWN.
TO PREVENT ACCIDENTAL LOOSENING OF THE BACK SHELL PLACE A SMALL AMOUNT OF
DETAIL B
(LOCTITE 7649) AND ADHESIVE (LOCTITE 271) IN THREADS. TORQUE TO 0.5 N-m.
SCALE 2 : 1
BACK SHELL
WIRE COLOR TO LOC

HIROSE
R P/N HR30-6P-T02 CABLE LENGTH 1=BROWN, PVC 26
2=WHITE, PVC, 26 A
PLASTIC XX-CABLE LENGTH PART NUMBER 3=BLUE, PVC, 26 AW
EXTENSION
136
COMPRESSION 2 METERS (6.56FT) 02 4=BLACK, PVC, 26 A
.195±.020
FITTING 10 METERS (32.81FT) 10 5=DRAIN, PVC, 26 A
6=EMPTY
.100±.020
END “A”
PLUG INSULATOR BODY DETAIL C

SCALE 2 : 1
SECTION A
SCALE 4
Figure 13: Cable, IS (ref. dwg. 704-1318, SH 2 of 2)

OSE SOLDER FIXTURE
/N HR30-6P-6S-T01

Hazardous Location Non-Hazardous Location

POWER SUPPLY
ZBB BUS BAR
BROWN RED
3 1 +24V
4 2
BLUE GREEN
24V RETURN
GREEN
BLACK
oxy.IQ Transmitter MTL7706
IS GROUND
IS Cable 4-20MA ANALOG
704-1318-xx INPUT DEVICE
(Blue Jacket) Non-IS Cable
R1
1. Equipment connected to barrier
inputs must not use or generate
BLACK
more than 250V.
2. Total load of R1 + R2 must equal R2
250 ohms ±5%.
Hazardous Location Non-Hazardous Location

POWER SUPPLY
Class 1 Div 2 Enclosure
BLUE
+24V
24V RETURN
oxy.IQ Transmitter
BROWN
BROWN
704-1317-xx 4-20MA ANALOG

(Black Jacket) INPUT DEVICE
Maximum load of analog input device is

dependent on power supply voltage
and cable resistance.
1. For Class 1 Div 2 installation, the oxy.IQ shall be installed in
an appropriately rated final enclosure accepting a Division 2
wiring method per NEC/CEC.
Non-Hazardous Location POWER SUPPLY
BLUE
+24V
24V RETURN
oxy.IQ Transmitter
BROWN
BROWN
704-1317-xx 4-20MA ANALOG

(Black Jacket) INPUT DEVICE
Maximum load of analog input device is

dependent on power supply voltage
and cable resistance.
Figure 14: Wiring Options (ref. dwgs. 702-285 & 702-286)


138
Figure 15: Schematic Diagram (ref. dwg. 752-347)
44 oxy.IQ User’s Manual

Appendix B. Menu Maps

This appendix includes the following oxy.IQ menu maps:
• “User’s Menu Map” on page 46
• “Service Menu Map” on page 47

46
Main Menu
libration Display Output Service

Service Pass
Required
Air O2 Range
No ppm only Span Value

Yes % only
Trim
Auto Select
Span Gas
4 mA Trim
Display Range
Flow Span Gas 20 mA Trim
On
Sensor Life Error Type
Off
Use Days High O2
140
Contrast
Low O2
Enter Value High Temp
Low Temp
Temp Comp
Figure 16: User’s Menu Map

Error Output
None
Low
High
Value
NAMUR

Main Menu
Calibration Display Output Service

See User's Menu Map (no passcode required) Diagnostics
O2 uA
Output mA
Output %
Temp °C
141
Temp Res
Gain
OX-n (n=1-4)
Figure 17: Service Menu Map

Sensor Type
OX-1
OX-2
OX-3
OX-4

47

Appendix C. Order String
oxy.IQ BCD-E
A Model Only
oxy.IQ Oxygen Transmitter; 4 to 20 mA output
B Sensor
0 No sensor
1 Standard ppm, 0 to 10, 20, 50, 100, 200, 500, 1000 ppm
2 Acid ppm, 0 to 10, 20, 50, 100, 200, 500, 1000 ppm
3 Standard percent sensor
4 Acid percent sensor
5 Standard ppm, 0 to 100, 200, 500 and 1000 ppm
C Package
1 Standard Package
3 Intrinsically safe (US/CAN Class 1 Div 1) or
Non-incendive (US/CAN Class 1 Div 2)
4 Ex flameproof
D- Cable Length
0 No cable
1 2 meter cable
2 10 meter cable
E Zener Barrier
0 None
1 Zener barrier
2 Galvanic isolator.
Note: For Class 1 Div 1 either zener barrier or
galvanic isolator must be selected. For
Class 1 Div 2, no barriers neeed. Please
refer to dwg 752-347 for installation
guidelines.
Example part number: oxy.IQ 132-1


Appendix D. Certifications
The following oxy.IQ certifications are included in this appendix:
• “ATEX EU-Type Examination Certificate” on page 52
• “ATEX IECEx MAM Ex Certificate” on page 56
• “Canadian Certificate of Compliance” on page 58
• “FM Certificate of Compliance” on page 61
• “IECEx Certificate of Conformity” on page 64

D.1 ATEX EU-Type Examination Certificate
1 EU-TYPE EXAMINATION CERTIFICATE

2 Equipment or Protective systems intended for use in Potentially
Explosive Atmospheres - Directive 2014/34/EU
3 EU-Type Examination Certificate No: FM14ATEX0032X
4 Equipment or protective system: Model oxy.IQ Oxygen Transmitter
(Type Reference and Name)
5 Name of Applicant: GE Infrastructure Sensing
6 Address of Applicant: 1100 Technology Park Drive

Billerica, MA 01821
USA
7 This equipment or protective system and any acceptable variation thereto is specified in the schedule to this
certificate and documents therein referred to.
8 FM Approvals Ltd, notified body number 1725 in accordance with Article 17 of Directive 2014/34/EU of
26 February 2014, certifies that this equipment has been found to comply with the Essential Health and
Safety Requirements relating to the design and construction of equipment intended for use in potentially
explosive atmospheres given in Annex II to the Directive.
The examination and test results are recorded in confidential report number:
3047174 dated 23rd February 2015
9 Compliance with the Essential Health and Safety Requirements, with the exception of those identified in item
15 of the schedule to this certificate, has been assessed by compliance with the following documents:
EN 60079-0:2012 +A11:2013 and EN 60079-11:2012
10 If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to specific
conditions of use specified in the schedule to this certificate.
11 This EU-Type Examination certificate relates only to the design, examination and tests of the specified
equipment or protective system in accordance to the directive 2014/34/EU. Further requirements of the
Directive apply to the manufacturing process and supply of this equipment or protective system. These are
not covered by this certificate.
12 The marking of the equipment or protective system shall include:
II 1 G Ex ia IIC T4 Ga; Tamb = -20˚C to +60˚C

!"##$&$*;;
Mick Gower
Certification Manager, FM Approvals Ltd..
Issue date: 15th June 2017
THIS CERTIFICATE MAY ONLY BE REPRODUCED IN ITS ENTIRETY AND WITHOUT CHANGE
FM Approvals Ltd. 1 Windsor Dials, Windsor, Berkshire, UK. SL4 1RS
T: +44 (0) 1753 750 000 F: +44 (0) 1753 868 700 E-mail: [email protected] www.fmapprovals.com
F ATEX 020 (Apr/16) Page 1 of 3

D.1 ATEX EU-Type Examination Certificate (cont.)
SCHEDULE
to EU-Type Examination Certificate No. FM14ATEX0032X
13 Description of Equipment or Protective System:

The Model oxy.IQ is a two-wire, loop-powered transmitter for measuring oxygen in ten ppm ranges and
seven percentage ranges. The Model oxy.IQ Transmitter contains one of five different oxygen cells. The
cells are specified to be part numbers OX-1, OX-2, OX-3 and OX-4 and OX-5. The type of oxygen cell
determines the range of measurement. The measured oxygen is converted to a mA signal for delivery to
the control equipment located in the non-hazardous area.
The Model oxy.IQ Transmitter’s electronics are contained on one printed circuit board. The circuit board is
located inside of a metallic housing. An oxygen cell holder is connected to the circuit board by way of pins.
The base of the oxygen cell holder contains a threaded joint for replacement of the oxygen cell. The
housing contains a polymeric window display. The polymeric window is approximately 1” by ¾”.The
housing, including the sensor assembly, is approximately 4.1” in height, by 2.75” in width, and 2.05” in
depth.
oxy.IQ-a3b-c0. Oxygen Transmitter.

a = Sensor: 0, 1, 2, 3, 4 or 5.
b = Cable Length: 0, 1 or 2.
c = Barrier: 0, 1 or 2.
Operation Temperature Ranges:

The ambient operating temperature range of the Model oxy.IQ Transmitter is -20°C to +60˚C.
The Transmitter is specified for use in normal atmospheric conditions.
Intrinsically Safe Energy Limitation Parameters:

Ui = 28V, Ii = 150mA, Pi = = 1.05W, Ci = 0, Li = 0.
14 Specific Conditions of Use:

The Model oxy.IQ Oxygen Transmitter will not pass the 500Vrms dielectric strength test. This must be
taken into account during installation.
15 Essential Health and Safety Requirements:

The relevant EHSRs that have not been addressed by the standards listed in this certificate have been
identified and assessed in the confidential report identified in item 8.
16 Test and Assessment Procedure and Conditions:

This EU-Type Examination Certificate is the result of testing of a sample of the product submitted, in
accordance with the provisions of the relevant specific standard(s), and assessment of supporting
documentation. It does not imply an assessment of the whole production.
Whilst this certificate may be used in support of a manufacturer’s claim for CE Marking, FM Approvals Ltd
accepts no responsibility for the compliance of the equipment against all applicable Directives in all
applications.
This Certificate has been issued in accordance with FM Approvals Ltd’s ATEX Certification Scheme.
17 Schedule Drawings
A list of the significant parts of the technical documentation is annexed to this certificate and a copy has
been kept by the Notified Body.

SCHEDULE
to EU-Type Examination Certificate No. FM14ATEX0032X
18 Certificate History
Details of the supplements to this certificate are described below:
Date Description
24th February 2015 Original Issue.

Supplement 1:
Report Reference: RR203799 dated 26th January 2016
28th January 2016 Description of the Change:
1. Minor changes and documentation updates.
2. New Manufacturing Location.
Supplement 2:
Report Reference: – RR209822 Dated 13th June 2017.
15th June 2017 Description of the Change:
1. Updated certificate to new EU format.
2. Updated documentation list.

Blueprint Report
GE Infrastructure Sensing Inc (1000000179)
Class No 3610
Original Project I.D. 3047174
Certificate I.D. FM14ATEX0032X
Drawing No. Revision Level Drawing Title Last Report Electronic Drawing
714-1344 C Oxy.IQ Safety Manual RR209822 Yes (pdf)
752-341 C MAIN PCB RR209822 Yes (pdf)
752-347 B Schematic Diagram - System Diagram oxy.IQ -FM Controlled Document RR209822 Yes (pdf)
15/06/2017 Page 1 of 1

D.2 ATEX IECEx MAM Ex Certificate

D.2 ATEX IECEx MAM Ex Certificate (cont.)

D.3 Canadian Certificate of Compliance
CERTIFICATE OF CONFORMITY
1. HAZARDOUS LOCATION ELECTRICAL EQUIPMENT PER CANADIAN REQUIREMENTS

2. Certificate No: FM17CA0101X
3. Equipment: Model oxy.IQ Oxygen Transmitter
4. Name of Listing Company: GE Infrastructure Sensing
5. Address of Listing Company: 1100 Technology Park Drive

Billerica, MA 01821
USA
6. The examination and test results are recorded in confidential report number:
3047174 dated 3rd March 2015

7. FM Approvals LLC, certifies that the equipment described has been found to comply with the following Approval
standards and other documents:
CAN/CSA-E60079-0:2011, CAN/CSA -E60079-11:2014

CAN/CSA-C22.2 No. 61010-1:2004
8. If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to specific
9. This certificate relates to the design, examination and testing of the products specified herein. The FM
Approvals surveillance audit program has further determined that the manufacturing processes and quality
control procedures in place are satisfactory to manufacture the product as examined, tested and Approved.
10. Equipment Ratings:
Intrinsically Safe (Entity) for use in Class I, Division 1, Groups A, B, C and D; Temperature Class T4 Tamb =
-20˚C to +60˚C in accordance with Control Drawing No. 752-347; Ex ia IIC T4 Tamb = -20˚C to
+60˚C; in accordance with Control Drawing No. 752-347; Nonincendive for use in Class I, Division 2, Groups A,
B, C and D; Temperature Class T4 Tamb = -20˚C to +60˚C Hazardous Locations.
Certificate issued by:
13 June 2017
J. E. Marquedant Date
VP, Manager, Electrical Systems
To verify the availability of the Approved product, please refer to www.approvalguide.com
FM Approvals LLC. 1151 Boston-Providence Turnpike, Norwood, MA 02062 USA
F 348 (Mar 16) Page 1 of 3

D.3 Canadian Certificate of Compliance (cont.)
SCHEDULE
Canadian Certificate Of Conformity No: FM17CA0101X
11. The marking of the equipment shall include:
IS CL I DIV 1, GPS A, B, C, D;
CL I, DIV 2, GPS ABCD
Class I, Zone 0, Ex ia IIC T4 Ga
Tamb = -20°C to +60°C
Install per Control Drawing 752-347
12. Description of Equipment:
determines the range of measurement. The measured oxygen is converted to a mA signal for delivery to the
control equipment located in the non-hazardous area.
housing contains a polymeric window display. The polymeric window is approximately 1” by ¾”.The housing,
including the sensor assembly, is approximately 4.1” in height, by 2.75” in width, and 2.05” in depth.


Ui = 28V, Ii = 150mA, Pi = = 1.05W, Ci = 0, Li = 0.
Model oxy.IQ-a3b-c0. Oxygen Transmitter.

a = Sensor: 0, 1, 2, 3, 4 or 5.
13. Specific Conditions of Use:
1. The Model oxy.IQ Oxygen Transmitter will not pass the 500Vrms dielectric strength test. This must be
2. When installed in a Division 2 location, the Model oxy.IQ Oxygen Transmitter shall be installed in a final
enclosure accepting a Division 2 wiring method per the CEC.
14. Test and Assessment Procedure and Conditions:
This Certificate has been issued in accordance with FM Approvals Canadian Certification Scheme.
F 348 (Mar 16) Page 2 of 3

D.3 Canadian Certificate of Compliance (cont.)
SCHEDULE
Canadian Certificate Of Conformity No: FM17CA0101X
15. Schedule Drawings
A copy of the technical documentation has been kept by FM Approvals.
16. Certificate History
Date Description
23rd February 2015 Original Issue.

Supplement 1:
1. Updated certificate to new format.
2. Addition of Class I, Division 2 markings
F 348 (Mar 16) Page 3 of 3

D.4 FM Certificate of Compliance
CERTIFICATE OF CONFORMITY
1. HAZARDOUS (CLASSIFIED) LOCATION ELECTRICAL EQUIPMENT PER US REQUIREMENTS

2. Certificate No: FM17US0190X
3. Equipment: Model oxy.IQ Oxygen Transmitter
4. Name of Listing Company: GE Infrastructure Sensing
5. Address of Listing Company: 1100 Technology Park Drive

Billerica, MA 01821
USA
6. The examination and test results are recorded in confidential report number:
3047174 dated 3rd March 2015

7. FM Approvals LLC, certifies that the equipment described has been found to comply with the following Approval
standards and other documents:
FM Class 3600:2011, FM Class 3610:2010, FM Class 3810:2005,

ANSI/ISA 60079-0:2013, ANSI/UL 60079-11:2013, ANSI/ISA 61010-1:2004
8. If the sign ‘X’ is placed after the certificate number, it indicates that the equipment is subject to specific
9. This certificate relates to the design, examination and testing of the products specified herein. The FM
Approvals surveillance audit program has further determined that the manufacturing processes and quality
control procedures in place are satisfactory to manufacture the product as examined, tested and Approved.
10. Equipment Ratings:
Intrinsically Safe (Entity) for use in Class I, Division 1, Groups A, B, C and D; Temperature Class T4
Tamb = -20˚C to +60˚C in accordance with Control Drawing No.752-347; Intrinsically safe (Entity) for use in
Class I, Zone 0, AEx ia IIC T4 Tamb = -20˚C to +60˚C; in accordance with Control Drawing No.
752-347; Nonincendive for us in Class I, Division 2, Groups A, B, C and D; Temperature Class T4
Tamb = -20˚C to +60˚C; Hazardous (Classified) Location.
Certificate issued by:
13 June 2017
J. E. Marquedant Date
VP, Manager, Electrical Systems
To verify the availability of the Approved product, please refer to www.approvalguide.com
F 347 (Mar 16) Page 1 of 3

D.4 FM Certificate of Compliance (cont.)
SCHEDULE
US Certificate Of Conformity No: FM17US0190X
11. The marking of the equipment shall include:
IS CL I DIV 1, GPS A, B, C, D;
CL I, DIV 2, GPS ABCD
Class I, Zone 0, AEx ia IIC T4 Ga
Tamb = -20°C to +60°C
Install per Control Drawing 752-347
12. Description of Equipment:
determines the range of measurement. The measured oxygen is converted to a mA signal for delivery to the
control equipment located in the non-hazardous area.
housing contains a polymeric window display. The polymeric window is approximately 1” by ¾”.The housing,
including the sensor assembly, is approximately 4.1” in height, by 2.75” in width, and 2.05” in depth.


Ui = 28V, Ii = 150mA, Pi = = 1.05W, Ci = 0, Li = 0.
Model oxy.IQ-a3b-c0. Oxygen Transmitter.

a = Sensor: 0, 1, 2, 3, 4 or 5.
13. Specific Conditions of Use:
1. The Model oxy.IQ Oxygen Transmitter will not pass the 500Vrms dielectric strength test. This must be
2. When installed in a Division 2 location, the Model oxy.IQ Oxygen Transmitter shall be installed in a final
enclosure accepting a Division 2 wiring method per the NEC.
14. Test and Assessment Procedure and Conditions:
This Certificate has been issued in accordance with FM Approvals US Certification Requirements.
F 347 (Mar 16) Page 2 of 3

D.4 FM Certificate of Compliance (cont.)
SCHEDULE
US Certificate Of Conformity No: FM17US0190X
15. Schedule Drawings
A copy of the technical documentation has been kept by FM Approvals.
16. Certificate History
Date Description
23rd February 2015 Original Issue.

Supplement 1:
1. Updated certificate to new format.
2. Addition of Class I, Division 2 markings
F 347 (Mar 16) Page 3 of 3

D.5 IECEx Certificate of Conformity
,(&([&HUWLILFDWH
RI&RQIRUPLW\
,17(51$7,21$/(/(&7527(&+1,&$/&200,66,21
,(&&HUWLILFDWLRQ6FKHPHIRU([SORVLYH$WPRVSKHUHV
IRUUXOHVDQGGHWDLOVRIWKH,(&([6FKHPHYLVLWZZZLHFH[FRP
&HUWLILFDWH1R ,(&([)0*; ,VVXH1R &HUWLILFDWHKLVWRU\

,VVXH1R
6WDWXV &XUUHQW ,VVXH1R
3DJHRI ,VVXH1R
'DWHRI,VVXH
$SSOLFDQW *(,QIUDVWUXFWXUH6HQVLQJ
7HFKQRORJ\3DUN'ULYH
%LOOHULFD0$
8QLWHG6WDWHVRI$PHULFD
(TXLSPHQW 0RGHOR[\,42[\JHQ7UDQVPLWWHU
2SWLRQDODFFHVVRU\
7\SHRI3URWHFWLRQ ,QWULQVLF6DIHW\
0DUNLQJ
([LD,,&7*Dr&ื7Dืr&
(QHUJ\/LPLWDWLRQ3DUDPHWHUVb
8L 9,L P$3L :&L /L
$SSURYHGIRULVVXHRQEHKDOIRIWKH,(&([ -DPHV0DUTXHGDQW
&HUWLILFDWLRQ%RG\
3RVLWLRQ 930DQDJHU(OHFWULFDO6\VWHPV
6LJQDWXUH
IRUSULQWHGYHUVLRQ
'DWH
7KLVFHUWLILFDWHDQGVFKHGXOHPD\RQO\EHUHSURGXFHGLQIXOO
7KLVFHUWLILFDWHLVQRWWUDQVIHUDEOHDQGUHPDLQVWKHSURSHUW\RIWKHLVVXLQJERG\
7KH6WDWXVDQGDXWKHQWLFLW\RIWKLVFHUWLILFDWHPD\EHYHULILHGE\YLVLWLQJWKH2IILFLDO,(&([:HEVLWH
&HUWLILFDWHLVVXHGE\
)0$SSURYDOV//&
%RVWRQ3URYLGHQFH7XUQSLNH
1RUZRRG0$
8QLWHG6WDWHVRI$PHULFD

D.5 IECEx Certificate of Conformity (cont.)
,(&([&HUWLILFDWH
RI&RQIRUPLW\
&HUWLILFDWH1R ,(&([)0*; ,VVXH1R
'DWHRI,VVXH
3DJHRI
0DQXIDFWXUHU *(6HQVLQJ(0($
)5((=21(($676+$1121
&2&/$5(99
,UHODQG
$GGLWLRQDO0DQXIDFWXULQJORFDWLRQV
7KLVFHUWLILFDWHLVLVVXHGDVYHULILFDWLRQWKDWDVDPSOHVUHSUHVHQWDWLYHRISURGXFWLRQZDVDVVHVVHGDQGWHVWHGDQGIRXQGWRFRPSO\ZLWKWKH
,(&6WDQGDUGOLVWEHORZDQGWKDWWKHPDQXIDFWXUHU
VTXDOLW\V\VWHPUHODWLQJWRWKH([SURGXFWVFRYHUHGE\WKLVFHUWLILFDWHZDVDVVHVVHGDQG
IRXQGWRFRPSO\ZLWKWKH,(&([4XDOLW\V\VWHPUHTXLUHPHQWV7KLVFHUWLILFDWHLVJUDQWHGVXEMHFWWRWKHFRQGLWLRQVDVVHWRXWLQ,(&([6FKHPH
5XOHV,(&([DQG2SHUDWLRQDO'RFXPHQWVDVDPHQGHG
67$1'$5'6
7KHHOHFWULFDODSSDUDWXVDQGDQ\DFFHSWDEOHYDULDWLRQVWRLWVSHFLILHGLQWKHVFKHGXOHRIWKLVFHUWLILFDWHDQGWKHLGHQWLILHGGRFXPHQWVZDVIRXQG
WRFRPSO\ZLWKWKHIROORZLQJVWDQGDUGV
,(& ([SORVLYHDWPRVSKHUHV3DUW*HQHUDOUHTXLUHPHQWV
(GLWLRQ
,(& ([SORVLYHDWPRVSKHUHV3DUW(TXLSPHQWSURWHFWLRQE\LQWULQVLFVDIHW\L
(GLWLRQ
7KLV&HUWLILFDWHGRHVQRWLQGLFDWHFRPSOLDQFHZLWKHOHFWULFDOVDIHW\DQGSHUIRUPDQFHUHTXLUHPHQWVRWKHUWKDQWKRVHH[SUHVVO\LQFOXGHGLQWKH
6WDQGDUGVOLVWHGDERYH
7(67 $66(660(175(32576
$VDPSOHVRIWKHHTXLSPHQWOLVWHGKDVVXFFHVVIXOO\PHWWKHH[DPLQDWLRQDQGWHVWUHTXLUHPHQWVDVUHFRUGHGLQ
7HVW5HSRUW
86)0*([75 86)0*([75 86)0*([75
4XDOLW\$VVHVVPHQW5HSRUW
*%%$64$5



Index
A
Adjusting, oxy.IQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Air Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Analog Output
see Output
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B
Buttons, Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
C
Cable
Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Longer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Calculating Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Calibration
Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Existing Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
New Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
oxy.IQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Span Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Contrast, Adjusting Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
D
Diagnostics Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Display
Contrast, Adjusting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 23
O2 Parameter, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Range, Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Document Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Drawings, Outline & Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Index
E
Error
Output Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Type, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
F
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
I
Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installation
Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Mounting the oxy.IQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Oxygen Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sensor Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Interference Gases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Intrinsically Safe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
K
Keypad, Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
L
Label, Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
M
Main Menu
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Menu
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21, 23
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 21, 25
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 21
Menu Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Main Menu, Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Main Menu, User’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Mounting the Oxy.IQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Index
O
O2 Display Parameter, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Order String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
O-Ring, Sensor Manifold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Outline & Installation Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 37
Output
Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Error Condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Error Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
High (20 mA), Trimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Low (4 mA), Trimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 25
Range, Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Trimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
oxy.IQ
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Calibrating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Calibration, Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Calibration, Span Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Output Range, Selecting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Oxygen Sensor
Calibration, Existing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Calibration, New . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Sensor Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
P
Passcode, Service Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Pressure Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming, User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Publication Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
R
Range
Selecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Setting Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

Index
RoHS Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
S
Safety
Auxiliary Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
General Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Personal Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Sample System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 7
Sensor Manifold
Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
O-Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Service Menu
Diagnostics Option. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Menu Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Passcode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Span Gas Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Support
Customer Support Centers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
T
Terms and Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Trimming
Analog Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Output, High (20 mA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Output, Low (4 mA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Typographical Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
W
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
WEEE Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Wiring the oxy.IQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Addendum A. oxy.IQ Safety Manual

GE Sensing
oxy.IQ 1100 Technology Park Drive Oxy.IQ Safety Manual
Billerica, MA 01821
MODEL DWG NO. 714-1344 REV. C TITLE
Certification & Safety Statements for the oxy.IQ oxygen Transmitter

The oxy.IQ is a highly reliable and cost-effective two-wire, loop-powered transmitter
with a linearized 4 to 20 mA output. It measures oxygen in ten ppm ranges and seven
percentage ranges. All ranges are user-selectable. This compact transmitter uses
proven sensor technology to accurately measure O2 in a variety of gases, even in
hazardous environments.
When installing this apparatus, the following requirements must be met:
• The system is covered by the certificate numbers FM14ATEX0032X and IECEx
FMG 14.00016X as shown on the labels on the following page. The system
temperature code is T4 in the temperature range of -20 to 60°C.
• The apparatus should be de-energized before servicing.
• Installation shall be in accordance with the installation instructions and the
National Electrical Code® ANSI/NFPA 70, the Canadian Electrical Code C22.1, or
IEC/EN 60079-14, as applicable.
• Equipment is of type Intrinsically Safe and complies with: EN 60079-0:2012,
EN 60079-11:2012, IEC 60079-0:2007, IEC 60079-11:2006, IEC 60529:1992,
C22.2 No.1010.1:2004, CAN/ CSA-E60079-0:2011, CAN/CSA-E60079-11:2011,
C22.2.60529:2005, FM Class 3600:2011, FM Class 3610:2010, FM Class 3810:2005,
ANSI/ ISA 61010-1:2004 Ed.2, ANSI/ ISA 60079-0:2009 Ed.5,
ANSI/ ISA 60079-11:2009 Ed.5.
• The product contains no exposed parts which produce surface temperature
infrared, electromagnetic ionizing, or non-electrical dangers.
• The product must not be subjected to mechanical or thermal stresses in excess of
those permitted in the certification documentation and the instruction manual.
• The product cannot be repaired by the user; it must be replaced by an equivalent
certified product. Repairs should only be carried out by the manufacturer or by an
approved repairer. Please contact GE Customer Support Center for repair,
maintenance or replacement of the product. For oxygen sensor replacements
please contact GE Customer Support Center.
U.S.A Ireland
The Boston Center GE Sensing EMEA
1100 Technology Park Drive Free Zone East, Shannon,
Billerica, MA 01821 Co. Clare, V14 V992, Ireland
U.S.A Tel: +35 361 470200
Tel: 800 833 9438 (toll-free), 978 437 1000
E-mail:[email protected]
Page 2 of 6
GE Sensing
Billerica, MA 01821
• Only trained, competent personnel may install, operate and maintain the
equipment.
• For product training please contact GE Customer Support Center:
U.S.A Ireland
The Boston Center GE Sensing EMEA
1100 Technology Park Drive Free Zone East, Shannon,
Billerica, MA 01821 Co. Clare, V14 V992, Ireland
U.S.A Tel: +35 361 470200
Tel: 800 833 9438 (toll-free), 978 437 1000
E-mail:[email protected]
• The product is an electrical apparatus and must be installed in the hazardous area
in accordance with the requirements of the EC Type Examination Certificate. The
installation must be carried out in accordance with all the appropriate
international, national and local standard codes and practices and site
regulations for Intrinsically Safe apparatus and in accordance with the
instructions contained in the manual. Access to the circuitry must not be made
during operation.
• The maximum operating pressure for the oxy.IQ is 10psi. Be sure the sample
conditioning system is designed to maintain the oxy.IQ pressure below these
limits, and that the oxy.IQ outlet is vented to atmosphere during operation and
calibration.
• WARNING - Substitution of components may impair Intrinsic Safety.
• WARNING - To prevent ignition of flammable or combustible atmospheres,
disconnect power before servicing.
• AVERTISSEMENT - Pour éviter l'inflammation d'atmosphères inflammables ou
combustibles, débrancher l'alimentation avant l'entretien.
• AVERTISSEMENT - Remplacement des composants peut compromettre la
sécurité intrinsèque.
• Equipment is not intended for the measurement of oxygen in fluid of liquid phase.
Special Conditions of Safe Use

1. The Model oxy.IQ will not pass the 500V dielectric test. This must be taken into
account upon installation.
2. When installed in a Division 2 location, the Model oxy.IQ oxygen transmitter shall
be installed in a final enclosure accepting a Division 2 wiring method per
NEC/CEC.
Page 3 of 6
GE Sensing
Billerica, MA 01821
Markings
Markings shall appear on the oxy.IQ as shown below for the Intrinsically Safe version
of the product.
II 1 G
Page 4 of 6
GE Sensing
Billerica, MA 01821
Connection and Wiring Diagram

The following diagram is the entity parameters for the oxy.IQ.
Page 5 of 6
GE Sensing
Billerica, MA 01821
Power Requirements:
Nominal Operating Parameters: 28VDC at 50mA
Blue (+)
Brown (-)
Power Connector
Page 6 of 6

GE
EU DECLARATION
Sensing
OF
CONFORMITY
DOC-0046, Rev. C
We, GE Sensing
1100 Technology Park Drive
Billerica, MA 01821
USA
declare under our sole responsibility that the

oxy.IQ™ Oxygen Transmitter
to which this declaration relates, is in conformity with the following standards:
• EN 60079-0:2012+A11:2013
• EN 60079-11:2012, II 1 G – Ex ia IIC T4 Ga
QAN license 0795 : SGS Baseefa Ltd, Buxton SK17 9RZ, UK - NoBo# 1180
• EN 61326-1: 2013, Group 1, Class A, Industrial EM Environments

• EN 61326-2-3: 2013
following the provisions of directives 2014/30/EU (EMC) and 2014/34/EU (ATEX).
EU Type Examination Certificate:
• FM14ATEX0032X
FM Approvals Ltd, Windsor SL4 1RS, UK - NoBo# 1725
The product listed above, and any ancillary equipment supplied with it, does not
bear the CE mark for directive 2014/68/EU (Pressure Equipment) as it falls under
Article 4, section 3 (sound engineering practice) for DN <25.
Directive 2014/35/EU is not applicable due to the 28 V d.c. maximum operation
voltage.
Billerica - October 25, 2016

Mr. Chris Frail
Engineering Manager

172

173
174
Customer Support Centers
U.S.A.
The Boston Center
1100 Technology Park Drive
Billerica, MA 01821
U.S.A.
Tel: 800 833 9438 (toll-free)
978 437 1000
E-mail: [email protected]
Ireland
Sensing House
Shannon Free Zone East
Shannon, County Clare
Ireland
Tel: +35 361 470200
E-mail: [email protected]
bhge.com
© 2017 Baker Hughes, a GE company – All rights reserved.
Baker Hughes reserves the right to make changes in specifications and features shown
herein, or discontinue the product described at any time without notice or obligation.
Contact your BHGE representative for the most current information. The Baker Hughes
logo is a trade mark of Baker Hughes, a GE company. The GE Monogram is a trademark of
the General Electric Company.
910-296 Rev. D
175

GE Panametrics O.XY IQ Manual

Uploaded by

Copyright:

Available Formats

GE Panametrics O.XY IQ Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GE Panametrics O.XY IQ Manual

Uploaded by

Copyright:

Available Formats

TurkStream Onshore Receiving Terminal

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

bhge.com 910-296 Rev. D

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

Terms and Conditions

CAUTION! This symbol indicates a risk of potential minor

WARNING! This symbol indicates a risk of potential serious

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

WARNING! It is the responsibility of the user to make sure all

Attention European Customers! To meet CE Marking

WARNING! Auxiliary equipment may have both manual and

WARNING! Make sure that power to the auxiliary equipment

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

Personal Safety Equipment

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

In order to avoid the dissemination of those substances in our environment

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

4.3.3 Adjust the Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

Chapter 1. Features and Capabilities

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

1.2 Hazardous Location Certifications

• Semiconductor wafer machines

• Coating process machines

• Membrane air separators

• Inert welding gases

• Pure gaseous hydrocarbon streams

• Process monitoring of gaseous monomers

• Heat treating and bright annealing

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

• Display with keypad

• Proven galvanic fuel cell O2 sensor technology

• User-selectable ranges for ppm and percent oxygen

• User-friendly and intuitive user interface with diagnostics

• Microprocessor-based, all-digital technology for reliable

• Sensor failure output error

• Sensor lifetime indication

• NAMUR error indication

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

1.5 Sample Systems

Table 1: Oxygen Sensor Interference Gases

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

Figure 2: Outline and Dimensions (ref. dwg. 712-1840)

Note: To avoid collecting condensate that may damage the oxygen

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

2.1 Mounting the oxy.IQ (cont.)

Figure 3: Packaged Oxygen Sensor

2. Remove the sensor manifold by unscrewing it from the blue

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

2.1 Mounting the oxy.IQ (cont.)

Sample Inlet Sample Outlet

PET-MSM-MAN-809439 - 01 - Reviewed - 02-05-2019 - 5 - For information only

2.2 Wiring the oxy.IQ

WARNING! For IS (Intrinsically Safe) applications, the oxy.IQ

1. Attach the appropriate cable to the oxy.IQ (see Figure 5 below). Be

Cable Connector Alignment Arrow