BSR 2020 Construction

Building Schedule of Rates
For
CONSTRUCTION WORKS
OF
Government Buildings
B.S.R -2020
Department of Buildings
B.S.R. Workgroup Committee,

Dept. of Buildings,
" Serhsiripaya",
Battaramulla.
Construction BSR 2020
Contents Page Nos.

A. INTRODUCTORY NOTES & ADDITIONS TO SPECIFICATIONS
A.1 INTRODUCTORY NOTES A01-A03

A.2 ADDITIONS TO SPECIFICATIONS A04-A07
B. PRICING PREAMBLES B01-B16
C. DEMOLITIONS C01-C01
D. EXCAVATION & EARTHWORK D01-D02
F. CONCRETE WORK F01-F04
G. MASONRY WORK G01-G02
H. WATER PROFING H01-H01
J. STRUCTURAL METAL WORK J01-J01
K. METAL WORK K01-K05
L. WOOD WORK L01-L09
L1 CARPENTRY-STRUCTURAL TIMBER WORK-(ROOF) L01-L01
L2 JOINERY (WALLS) L01-L05
L3 IRON MONGERY L05-L09
M. CLADDING M01-M01
N. PARTITION LINING / SUSPENDED CEILING N01-N06
P. ROOF COVERING P01-P03
Q. PLUMBING / SANITORY INSTALLATION Q01-Q16
R. MECHANICAL INSTALLATIONS R01-R06
S. ELECTRICAL INSTALLATION S01-S09
T. FINISHING & FLOORING T01-T05
T1 PLASTERER T01-T02
T2 PAVIOR T02-T05
U. GLAZING U01-U01
V. PAINTING & DECORATING V01-V03
W. DRAINAGE SYSTEMS W01-W03
X. EXTERNAL WORK X01-X02
2
A. INTRODUCTORY NOTES & ADDITIONS TO SPECIFICATIONS
A.1 INTRODUCTORY NOTES
A.1.1 Trade Names ;

Where trade names , brands and / or catalogue numbers are referred to sole
preference to any material or equipment is not intended . Any other material or
equipment may be used, provided that the characteristics of type,
quality,appearance, finish, method of construction and / or performance is not less
than what is specified and provided, and prior approval is obtained.
A.1.2 Based Standard
This BSR has been prepared generally in accordance with the principles of "Method
of Measurement of Building Works(First Revision) , Sri Lanka Standard 573:1999"
A.1.3 Analysis for Basic Rates

The Material and Labour component required for the various items of work including
the minimal plant required for same is detailed in the analysis of the Basic Rates
which consist of the following
(a) Materials
The quantities of material required for the items are computed from known data
and experience. Their total value is calculated on the basis of current prices at
source of supply. Unless otherwise stated wastage is allowed in the norms.
(b) Transport
This component provides for the cost of transport of material from sources of supply
to the sites of work. This component is usually added to the material cost.
(C) Labour
The labour wages are as approved by the Government from time to time and on the
basis of an 8 hour working day.
Rates used in this B.S.R. are as follows.
Category Rate/ Per day
Unskilled Labour 1500
Semi Skilled Labour 1700
Skilled Labour 1900
Special Skilled Labour 2100
(d) Plant
This component provides for the minimum plant required for the item of work. The
cost of tools is provided for in the Overheads component.
(e) Basic Cost

The basic cost is the sum of the costs of items (a),(b),(c)and (d) above.
A-1 This BSR is for Construction works only

A.1.4 Preliminaries
Preliminaries for building works should be claimed under guide lines of ICTAD
Publication No. ICTAD/ID/04 Second Edition - June 2009
A.1.5 Overheads and Profit factors
These rates dose not include any overhead and profit factors and taxes such as
VAT etc. Hence it should be included whenever necessry according to the nature of
the contract considering the usage of priliminaries as mentioned in the clause A1.4
above.
A.1.6 Allowances for lifting work
Allowances to be made in the rates for lifting respect of work on upper floors.
In the analysis of the various items of work (other than specified) in the following
pages, the rates refer to work on the ground floor.
(a). Ground and 3 upper floors
To these rates the percentage (of the ground floor rates) indicated in table below
should be added to obtain the rates applicable to the 1st, 2nd and 3rd floors. This
B.S.R is limited to work on the ground and 3 upper floors only.
Serial Ground to 1st Ground to 2nd Ground to 3rd
Item
No. floor % floor % floor %
1 Concrete 3 5 7
2 9" Brickwork (Area wise) 5 7 9
3 9" Brickwork (Volume wise) 5 7 10
4 4 1/2" Brickwork 5 7 10
5 Steel reinforcement 2.5 5 4.5
6 Plastering 5 10 15
7 Floor Tiling 2 4 6
8 Wall Tilling 2 4 6
9 Roof Calicut tile 3 6 9
10 Roof asbestos 3 5 7
11 Ceiling work 3 5 7
12 Painting 3 6 9
(b).Fourth floor and above

If a building has more than four floors or when the contract period is compressed to
a few months, then it will be necessary to allow for the use of heavy machinery such
as tower crane, mobile cranes, dumpers loaders, batching plant for mixing of
concrete ,bins for the storage of concrete material etc.and also for the employment
of contract managers and additional staff.
The cost of such items of work will not be accommodated within the general ' Mark-
Up' and will have to be provided for in separate items such as preliminaries to the
contract.

A.1.7 Earth work and landscaping

Soils met within excavation have been classified as follows.
1. Soft /Loose soil
2. Ordinary soil
3. Hard /Dense soil
4. Mud/ wet clay
5. Soft disintegrated rock(i.e. rock not requiring blasting)
6. Hard rock - a) Where blasting is approved
b) Where blasting is prohibited
The classification of soil in note 1 above and the analysis provide for the different
type of soil will help the estimator in arriving at the actual of excavation, for which
he will have to allow in his estimate.
Under note 1(6) b Hard rock ,an analysis is provided for removing Hard Rock met
with in foundation excavations where blasting is prohibited or cannot be done, like in
built up areas where blasting can cause damage to adjoining buildings
For excavation beyond the depth of 5' 0" an additional unskilled laborer should be
added for every additional depth of 5' 0" or part thereof for each cube of excavation
beyond the original 5' 0" depth

A.2 ADDITIONS TO SPECIFICATIONS

A.2.1 Timber :
Unless otherwise specified in the respective Trades / Sections , the timber for all
trades shall be as specified in Carpentry and Joinery.
All timbers under exceptional Circumstances, any equivalent timber to the given
Species may be used with the approval of the Engineer.
(Group-1): Door, Window and Fanlight Frames
Category A Satin Palu Milla Ketakala Tulang

Halmilla Mee Hulanhik Wewarana Valdel.
Kohomba
Category B Grandis
(Group-2): Door , Window and Fanlight Sashes , Cupboards,

Counters and Shelving
Category A Satin Tulan Halmilla Mahogany
Kohomba Wewarana Hulanhik Sooriya mara
Category B Ginisapu
(Group-3): Roof Framework

Category A Madan Milla Palu Wewarana Tulang
Mee Valdel. Micro Kolon Etathimbiri
Category B Domba Grandis
(Group-4): Ceiling Framework and Partitions

Category A Satin Palu Milla Ketakala Tulang
Halmilla Mee Hulanhik Wewarana Valdel.
Kohomba Etathimbiri
Category B Domba Grandis
(Group-5): Valance Board and Valley Boarding

Category A Kolon Tulang Val Del Kohomba Sooriya mara
Mahogany Satin Hulanhik Wewarana
Category B Ginisapu
(Group-6): Beadings :
Alstonia Mahogany Lunumidella
(Group-7): Special Timber

Jak Teak
Source: Selection of timber species- State Timber Coorporation.

A.2.2 Aluminium Panels

All Aluminium sections shall be fully treated extruded Aluminium alloy sections in
accordance with BS 1470,1471, 1473, 1474 or latest relevant EN standed
All Aluminium sections to be locally extruded
All Aluminium sections shall present clear, straight and sharply defined lines. They
shall be free from defects, impairing strength, appearance and durability.
Finish
All members shall be finished either by
( i ) Anodizing or
( ii ) Powder coating ( What ever specified in Aluminium Items )
Anodizing -Exposed surface of all members shall be anodized using two steps.
Anodizing process to an anodic thickness of not less than 10-15 microns and shall
be free of any defects.
Powder coating
Powder coating shall be carried out using polyester coating with proper and
appropriate pre- treatment to a thickness of not less than 60-80 microns, measured
on all significant surfaces.
Screws and Hardware Items
Concealed screws, nuts, bolts, rivets and other fastening devices shall be of
Aluminium, non-magnetic stainless steel or other approved corrosive resistant
materials. If visible, they shall blend with the finish of the framing Aluminium
sections.
Glass
Glazing shall be minimum of 5mm thick clear float glass. Glass shall be secured at
all edges with compression gaskets and glazing beads. When fixing glass, all
glazing sealant shall be carefully applied and cleaned off properly.
Workmanship
The fabrication and installation of all Aluminium work must be carried out by
specialist tradesmen.
All dimensions shown on the drawings and the shop drawings must be verified by
actual site measurement before fabrication and installation. Any cutting to enlarge
the size of openings and approved practical method to fill the excess void behind
frames required after installation shall be executed by the Contractor at his own
expense.
All Aluminium members shall be factory fabricated to the best standard of

workmanship under experienced factory supervision and control.
Materials, method of fabrication, assembly, installation, fastenings, supports,

braces, operating parts and the like shall be in accordance with the approved shop
drawings.
All joints in frames at corners, junctions and intersections shall be mechanically

jointed and be such that when assembled they are as strong and rigid as adjoining
sections. Due care must be taken to ensure that all joints are water tight and leak-
proof. Joint lines should not be visible.
Provisions must be made for expansion and contraction in horizontal and vertical
members which are exposed to the weather or environments. Any distortion of
members or any glass cracked or broken as a result of inadequate provisions must
be rectified by the Contractor at his own expenses.
All works shall be securely installed and anchored in position, set plumb, square
and level in accurate alignment with other work, all in accordance with the approved
shop drawings to the Engineer's satisfaction.( The allowable tolerance in terms of
specified dimensions shall be plus/minus 1.5mm.)
Submissions
The Contractor shall submit shop drawings showing the following information where
appropriate to the item ;
layout (Sectional plan and elevation) of complete assembly
- full size sections of members
- methods of assembly
- methods of glazing
- methods of installation, including
fixings caulking, flashing
- provisions for vertical and horizontal expansion
- junctions and trim to adjoining surfaces
- fittings and accessories
The Contractor shall submit certificates from the Aluminium manufacture and/or an
approved testing laboratory which attest that the coating thickness offered is as
specified.
Doors & Windows
Frame and /or sash sections shall be of extruded EN-AW 6063-T5 Aluminium Alloy
Aluminium Louvers
Fixed louvers shall be of the weather proof type, suitable for overcoming water
carried- over by wind and the fixed louvers shall have free areas of not less than
50%
The Contractor shall provide a guarantee in respect of the weatherproof properties

of the fixed louvers.
All powder coatings shall match the windows. Panels shall be so constructed as to
be completely weather proof at junctions with adjoin structures .

Partitions
The frames shall be properly machined to permit easy assembly and to form
weather-tight joints when caulked.
Partition members shall be 76mm in depth and the thickness of 1.2mm.
Following dimensions are applied for the frame members of each assembly units
Minimum Minimum
Assembly Unit Member Depth Member
(mm) Thickness (mm)
Casement Window,Fanlight 70 1.5
Sliding door/Window 80 1.5
Door 100 1.5
Fixed glass Window 100 1.5
Rates shall include for all necessary hinges, screws, rubber beadings, Skelton
bolts, Aluminium louvers, pinhead stickers, etc.(Door Locks ,Door Handles,Door
closers paid separately )
Locks- (Union or equivalent )

Hinges-(Union or equivalent )
Handle-Grade 304 stainless steel
**Reffer notes 7.(d), Under pricing preambles

B. PRICING PREAMBLES
1. GENERAL
a. The Bidder shall read and be conversant with the full description of workmanship and
materials as described in this document under section (A) ,Pricing preambles, notes on
trades in BSR and ICTAD Specification for the respective items of work/ trades prior to the
preparation of the Bid.
b. The Bidder shall refer to the relevant Clauses of Pricing Preamble when pricing composite
item of works.
c. The rate for each item must be comprehensive and must include for complying in all
respects with the requirements of the aforesaid specifications, these Pricing Preambles,
cover all the obligations under the Contract, and all matters and things necessary for the
proper construction, completion and maintenance of the Works. No claim for additional
payment shall be allowed for any error or misunderstanding by the Contractor of the work
involved.
d. The rate for each item shall also include for all the following -
i. Labour and all connected costs ;
ii. Materials and goods including all connected costs;
iii. Preparatory works and setting out of particular item ;
iv. Complying with regulations of the Municipal Council and/or any other relevant authority
under which particular item of work is to be executed unless otherwise included in the
Preliminaries ;
v. Fitting and fixing materials and goods in position, including hoisting to any height or
lowering to any depth and all temporary works, equipment and small tools ;
vi. Plant and equipment unless otherwise included in Preliminaries ;
vii. Handling of materials and working in situation where there is very restricted working space
or no working space ;
viii. Square cutting and Waste of materials ;
ix. Forming of ends, angles, miters and junctions between straight and raking or curved work ;
x. Protecting and cleaning ;
xi. All other incidental works and necessary works which are not described in the B.O.Q. but
described in the aforesaid specifications and or shown in the drawings for the proper
completion of the relevant item of work ;
B-1 This BSR is for Construction works only

xii. Establishment charges and overheads( not included in preliminaries or anywhere in the Bill
Of Quantities), and profits.
e. In addition to above, the rates for items of work in Substructure shall include for the works
at depths extending below ground water table where applicable including excavation under
water,removal and disposal of mud and sand and preparation of place to a condition
suitable for proper execution of the works.
2. EXCAVATION AND EARTHWORK
a. All works under this section are measured net and no working space is allowed.
b. The Contractor shall be responsible for the design and execution of the excavation method
which is subject to scrutiny by the Engineer. However, scrutiny by the Engineer shall not in
any way relieve the contractor of his responsibilities and duty of care.
c. Existing ground levels shown in the Drawings have been taken at the surface of the ground,
with no particular differentiation to indicate buried foundations, pavings etc.
d. The Contractor shall note that the rate for compacted earth fill and granular fill, stone,
gravel and sand beds shall include for imported materials or materials from borrow areas.
e. Rates for Excavation & Earthwork shall include for -
i. Accepting site as found and preparing to condition suitable for proper execution of the
Works
ii. Excavating by whatever means are necessary including excavation done manually or by
machine in any type of ground including ground with boulders (except rock) and excavation
around existing RCC. bored piles and jet grout piles ;
iii. Trimming sides, keeping clean and consolidating bottom of basement, sumps, pits
and trenches ;
iv. Backfilling and disposal of surplus excavated materials as specified and directed ;
Any necessary additional works required due to

v.
a. Working space required by the Contractor ;
b. Earthworks supports ;
c. Formwork ;
vi. Any additional trimming or appropriate backfilling to provide specified or approved
formations and profiles necessitated by the uneven excavation of the earth, unless
otherwise measured separately ;
f. Rates for compacted earth fill, granular fill and gravel and sand beds shall include for
finishing sub-grade to slopes and falls, depositing in layers, leveling, blinding, and machine
or hand-packing to form vertical or battered or level faces, and for forming sinking where
required under floor slabs or sub-floor layers.

g. Rates for approved damp-proof membrane shall include for laps, and straight, raking and
circular cutting, and for notching around all obstructions.
3. CONCRETE WORK
a. Rates for concrete work shall include for -
i. Mixing as per specification, depositing, handling, hoisting and placing at any height or depth
;
ii. In case of readymix concrete, transporting, admixtures, handling, pumping/hoisting and

placing at any height or depth ;
iii. Packing and tamping around reinforcement, including vibrating ;
iv. Contractor's designed kickers, construction joints and sealents ;
v. Finishing to slopes and falls, and preparing surface ready for screeds or paving, where
necessary, including cutting to sizes and temporary supports to form necessary grooves ;
vi. Curing ;
vii. Preparation of ground surface, grading to slope and falls, if any, and machine or hand
packing to form vertical or battered or level surface and all necessary formwork to edges of
blinding concrete in case of pile caps ground slab/ramps/beams.
FORMWORK:
a. Formwork for similar concrete members are measured together irrespective of the height or
depth and the shape or form.
b. Extra-over rate for a particular type of high quality formwork should be applied only for the
areas of formwork which requires such high quality type formwork as specified.
c. Formwork shall be properly designed and strictly as described in the specifications for the
particular type of concrete surface finish and it should be sufficiently strong and grout tight.
d. Faces of Jet grouting piles, masonry and concrete work which will be formed or used as
formwork shall not be measured as formwork and no payment shall be made for same.
e. Rate for formwork shall include for -
i. Fabricating setting up and erection at any height or depth ;
ii. Strutting, supporting through lower floors and supporting at any level, including additional
propping, strutting and supporting decks ;

iii. Coating with shuttering oil and or lining ;
iv. Easing, striking and removing ;
v. Cleaning, preparing for reuse ;
vi. Removal when no longer required ;
vii. Props, stays, struts, wedges, bolts, incidental items and materials such as nails, screws
anchors hooks etc ;
viii. All overlaps and passing at angles ;
ix. Labour at intersections and narrow widths ;
x. Rubbing down and making concrete surface good after removal of formwork ;
xi. All fillets, to form grooves, rebates and throats, splays or chamfers, raking and circular
cutting, and cutting around all pipes, sleeves, conduits, ducting, metal sections and fittings ;
xii. Providing samples as required by the Engineer of the different formed finishes specified.
REINFORCEMENT:
a. i. Standard length of reinforcing bar for the purpose of measurement shall be 6.0 m. or 12.0
m
ii. Payment for bar reinforcement shall be to be nearest Kilogram.
b. Rates for reinforcement shall include for -
i. Rolling margin ;
ii. Preparation of bar bending schedules ;
iii. Straightening as required and cleaning of bars ;
iv. Cutting, bending and binding ;
v. Hoisting and placing in position at any height or depth ;
vi. Binding wires, and cover blocks.
vii. Necessary spacers. (inevitable laps & chairs paid separately)
viii. Aligning and supporting in position during concreting.

PRECAST CONCRETE WORKS:
a. Rates for precast concrete works shall include for -
i. Moulds and for formwork with the required finish to all exposed surfaces in accordance with
the specifications, hacking surfaces to form key for rendering etc, and hoisting to any
height or depth including providing any lifting holes or other devices to the approval of the
Engineer,building in, including bedding and jointing in mortar as required, and any
necessary strutting and supporting.
ii. The requirements of the Pricing Preamble clauses which refer to Concrete
Work,Reinforcement and Formwork.
iii. Loading, transporting to Site, unloading, handling and stacking.
iv. Hoisting and fixing in position at any height or depth.
4. MASONRY WORK
a. In the calculation of the volumes of brick wall which are not multiples of the size of standard
bricks, the thickness of such walls shall be taken as the thickness of full bricks from which
they can be cut. The same principle of calculation of volume shall be used for all brickwork
of which the cross-sectional dimensions are not multiple of brick sizes.
b. Rates for brickwork/Block work shall include for -
i. Plumbing, angles,straight cutting,forming rebates,reveals and raking out joints for

plastering;
ii. Splay cutting, rough cutting, fair cutting, forming chases or grooves for slabs,
partitions,staircases, roofs and the like, bonding ends of walls, building in or cutting and
pinning in and making goods on lintels, timber and steel works ;
iii. Building at any level or height of slabs or beams, additional labour in kerbs, isolated and
attached piers, all cutting, bonding at angles and intersections, building into or against
adjacent work, wedging and pinning up to soffits;
iv. Supplying and fixing metal clamps, Galvanized, steel boundary ties, and brick reinforcement
etc;
v. Necessary cutting required in walls which are not multiples of brick size ;
vi. Preparing existing walls for raising and pinning new brickwork ;
vii. Bonding new walls to concrete faces and old walls where necessary, and materials to be
used for such bonding.
Damp Proof Course

a. Rates for Damp Proof Course shall include for -
i. Necessary leveling screed and trimming top of rubble/block/brick plinth wall ;
ii. Fair edges, rounded edges, drips and arises, angle fillets ;
iii. Turning nibs of asphalt into grooves ;
iv. Cutting to line and jointing new to old asphalt.
STONE WORK
a Generally
Stones are defined as consolidated aggregates of one or more minerals and includes all
types of rock used in the construction industry.
b Rubble work
Rubble Stone masonry built of stones either irregular in shape as quarried or shaved and
only hammer dressed and having comparatively thick joints.
Rates for Rubble Masonry shall include for -
i. All joggles, cramps, dowels, ties, templates ;
ii. Plumbing, angles, fair returns, setting, jointing, eaves filling, pointing and fixing in position,
hoisting to any given height or depth ;
iii. Bonding ends of walls, rough cutting and fair cutting ;
iv. Leveling up in walling for Damp Proof Courses, sills, thresholds, string courses, copings and
the like ;
v. Forming straight vertical joints next to dressings, panels, brickwork etc ;
vi. Forming openings and dressed margins ;
vii. Forming chases, throats, rebates, margin flutes, sinking, chamfered and rounded edges,
and all labour connected therewith.
c Ashlar Stone masonry using dressed stone blocks of given dimensions having faces
perpendicular to each other and laid in courses.
Rates for stone work shall include for:-
i. Extra material for curved work
ii. All rough and fair cutting
iii. Dressing
iv. Forming rough and fair grooves, throats, mortices, chases, rebates, holes, stops and
mitres.
v. Raking out joints for key

vi. Labours in eaves filling
vii. Dressed margins to rubble work
iix. Leveling uncoursed work
ix. Rough and fair square cutting
x. Centering
xi. Wedging up and pinning to concrete soffits and steel work
xii. Building in frames, flashing, damp proof courses including filling hollows of corner blocks
with mortar
xiii. Building in ties, lugs, plates, lintels, pipe sleeves, inserts, switch boxes and the like. As the
work proceeds.
d Stone Veneering work (Face rubble work)
i. Stone lining upto 80mm along planes parallel to natural bed. The natural bed may be
masonry of brickwork or rubbel work, concrete surface.
ii. Stones cut into slabs of required thickness.
iii. Dressed to very close tolerances.
5. WATER PROOFING
a. Rates for Water Proofing shall include for ;
i. For necessary leveling and trimming top of rubble/block/brick plinth wall ;
ii. Fair edges, rounded edges, drips and arises, angle fillets ;
iii. Forming internal and external angles, bonding bricks/blocks and the like ;
iv. Turning nibs of asphalt into grooves and asphalting around brackets ;
v. Cutting to line and jointing new to old asphalt ;
vi. Temporary screeds, ground and rules.
6. STRUCTURAL STEELWORK
a. Rate shall include for :
All shop fabrication work, including cutting, drilling, bolting, riveting, welding, grinding,
delivering, unloading, hoisting, erecting and fixing.
7. METAL WORKS
a. All Aluminium sections shall be fully treated extruded Aluminium alloy sections in
accordance with BS 1470,1471, 1473, 1474 or latest relevant EN Standed
b. Contractor to prepare shop drawings for approval of the Engineer.

c. Rates for Metal Work shall include for anchors, screws, dissimilar metals and providing
thermal movement and the preamble clauses for Structural Steel Work where relevant and
they shall apply equally to relevant items of this section.
Aluminum components
d. Fabrication & fixing of Aluminum components shall be carried out by experienced
tradesman.The Contractor shall furnish particulars of Aluminum fabricator through the
engineer for his approval.
The Contractor will be required to furnish a guarantee on material and workmanship for a
period of 8 years from the date of handing over of Works in the form required by the
employer, binding the Aluminum manufacturer and the Contractor jointly and severally
Material: As described under section A (Additions to specifications)
8. ROOF COVERING AND ROOF PLUMBING
a. Rates for roof covering and roof plumbing shall include for :
i. Hoisting, placing and fixing in position ;
ii. Straight cutting, raking cutting, circular cutting, notching, and working around obstructions
and waste ;
iii. Nails, screws and the like ;
iv. Drilling and making holes or opening and the like;
b. Rates for flashings shall include for the following in addition to the requirement of "a" above -
i. Bending and cutting to required shape and forming roll edges ;
ii. Angles, edges and ends ;
iii. Notching over roofing ribs or dressing into roof cover/concrete as the case may be ;
iv. Forming and dressing into or around walls at obstructions and the like ;
v. Stepping up ;
vi. Sealing with sealant materials.
9. CARPENTRY(Roof and ceiling frame)
a. Sizes of all timber given are finished sizes.

b. All timber shall be well seasoned and treated against insect and termite attack before
fixing in position
c. Rates for carpentry shall include for -
i. Any type of cutting required, sawing, notching, drilling, trimming, framing, jointing, splayed
edges and the like, hoisting and fixing in position with nails, spikes, plugs, screws, and
gluing and priming to joints and ends ;
ii. Forming splayed edge, grooves, chamfers, scribed and rounded edge, beveling,molding
and the like ;
iii. Plugging, wedging, nuts and washers with bolts,sprockets and pins and the like ;
iv. Nogging or solid bridging, cut between studs or joints for structural timber.
v. Rebating, singings, grooving, mortising ;
vi. Additional timber lengths required for carpentry jointing ;
vii. Protection and keeping clean for staining, polishing or painting where applicable ;
d. Rates for roof decking shall include for machine sanding, protecting and preparing in
addition to the requirements c above.
e. Rates for walls and ceiling lining shall include for jointing and fixing to walls/ ceiling/ eaves
etc. all cover and joint strips, in addition to the requirements c above.
f. Rates for timber paneling/wall lining shall include for cover moldings, sills, stiles and head
moldings to openings as relevant.
10. JOINERY
a. Sizes of all timber given are finished sizes.
b. All timber shall be well seasoned and treated against insect and termite attack before
fixing.
c. Timber used for joinery works shall be well seasoned well treated and in one species of
special class timber recommended for the particular class of Joinery works as specified in
the Specification.
d. Rates for Joinery shall include for -

i. Any type of cutting required, sawing, notching, drilling, trimming, planing, forming and
jointing and the like, fixing in position complete with nails, spikes, plugs, screws and gluing
and priming to joints and ends ;
ii. Forming splayed and tongued edges, rebates mortises, grooves, chamfers, scribed and
rounded edges, beveling, moulding, margin and the like and rounded corners, sinkings ;
iii. Working to stated sizes, for all short lengths making mitres, joints and ends ;

iv. Necessary bolts, dowels metal clips, anchors, grips and fixing joinery ;
v. Glueing, dowelling, plugging, wedging pining and the like ;
vi. Punching heads and filling with approved filler if nails or pins are used for fixing ;
vii. Countersinking and filling heads with approved filler, if brass screws are used for fixing ;
viii. Painting rebates of frames before fixing glass ;
ix. Bedding in cement mortar filling and hanging to frame lining ;
x. Keeping clean for staining, polishing or painting;
xi. Painting, Laquering or Varnishing as specified.
e. Preambles for Glazing section and a, b and c under Painting and Decorating section shall
equally apply to Joinery works.
f. Ironmongary
i. All cutting, fitting, sinking, boring, mortising ;
ii. Matching screws for ironmongery
iii. Removing during decoration, refixing after decoration, leaving oil and in proper working
order on completion and supplying and labeling all keys and handing over to Employer.
11. WALL,FLOOR AND CEILING FINISHES
a. i. All works under this trade shall be measured after deduction for voids,openings, doors and
windows
ii. All other small quantities/panels/narrow widths/ arises/ reveals/ angles/ ends/short lengths
including those of tiling work on door and window jambs and reveals are measured together
with the respective tiling item and labour in such work shall be included in the rate for the
main finishing item and they shall not be measured/paid separately.
b. Rates for wall, floor, ceiling finishings and wall floor screed and bedding shall include for -
i. All temporary rules, screeds, templates and supports, curing and cleaning off on completion
and exact thickness required to finish ;
ii. Caulked joints and making good and cutting around bolts, pipes conduits,sleeves, ducting,
fittings, sections, obstructions and the like ;
iii. Tamping and compacting ;
iv. Raking out joints of new brickwork/Block work or hacking concrete to form key, including
brushing, cleaning off and dampening ;
B - 10 This BSR is for Construction works only
v. Forming internal and external angles and arises ;
vi. Any extra thickness required to finish to true levels ;
vii. Any additional dubbing out required to plastered surfaces of brickwork and to the finished
surface of concrete to obtain the requisite standard of finish ;
viii. Samples to be submitted for the approval of the Engineer.
c. Rates for tile slab or block finishing to floor and wall shall also include for the following in
addition to the above -
i. Straight raking and circular cutting ;
ii. Dubbing out or packing to concrete surface to correct deviations within specified tolerance ;
iii. Laying or finishing to falls or cross falls ;
iv. Expansion joints at perimeter and between bays where required in case of floor tile paving ;
v. Sand blasting, cleaning, waxing and appropriate floor finishings.
d. Rates for ceiling lining shall include for the following
i. Working to sides and soffits of attached or isolated beams and soffit of staircases where
relevant;
ii. Additional forming required for lighting and air-conditioning grills ;
iii. Straight, raking and circular cutting ;
iv. Neoprene sealing for air tightness around hatches if any ;
v. Matching edges where cutting occurs and for filling the heads of fixings with approved filler
where relevant ;
vi. Painted mild steel hanging rods.

12. GLAZING
a. i. Type of Glazing shall be as specified.
ii. Thickness of glazing shall be as per the design of the approved specialist contractor who
will be engaged by the Contractor. However, the minimum thickness shall be 6mm.
b. Rates for Glazing shall include for -
i. Glazing, fixing, bedding priming and panel pins and other materials and labour for same
and cutting to size ;
ii. Templates, straight cutting, circular cutting, grinding edges or special type of edges required
and sand blasting ;
iii. Glazing beads, washlether or neoprene strip, glazing sealant, weather stripping, caulking
joint silicone joint ;
iv. Replacing cracked or broken glass ;
v. Making holes where necessary ;
vi. Samples to be submitted for the approval of the Engineer.
13. PAINTING AND DECORATING
Note
Colour and the quality of all paint and other painting materials shall be approved by the
Engineer prior to use.
a. Rates for painting shall include for -
i. Preparation of surfaces, cleaning down, smoothing, etc ;
ii. Submission of samples for the approval of the Engineer ;
iii. Protection of floors, walls and fittings etc ;
iv. Working to returns, painting in any colour, multi- colour works, cutting into line at junctions
of different colours at angles or plain surfaces, painting in small quantities ;
v. Cleaning down upon completion
b. Rates for work to isolated general surfaces shall include for working on door frames,
linings,window subframes (where of a differing material to the window), skirting, rails,
architrave's, bars,posts, balusters and the like.
c. Rates for work to glazed general surfaces, glazed windows and the like (measured both
sides,flat over glass, irrespective of size and panes) shall include for work to edges and
glazing rebates, returns and moldings of frames, mullions, transoms, architaves and the
like.

d. Rates for work to pipes and conduits (which shall include trunking, ducting and the like)
shall include for all work on hangers, supports, brackets and the like.
14. PLUMBING
a. The rates for Plumbing shall include for :
i. Refer specifications for full description of materials and workmanship.
ii. Screws, nails, sockets, connectors, backnuts, nipples, and standard pipe fixing or
supporting clips, saddles, brackets straps, screws, nails, solder rivets connectors, flanges
pipe sleeves, brackets, made bend holder bats and the like.
iii. Short lengths, joints connections and couplers in running length.
iv. Sealing, fixing and support with holder bats or pipe clips cut and pinned built in wall or
slabs.
v. Plugging screwing to walls or ceiling
vi. All laps, straight cutting and waste
vii. The fittings including bends, tees, collars, reducers elbows, valve sockets, junctions, caps
and the like for pipe less than or equal 50mm dia pipe.
viii. Jointing compound, solvent cement and incidental materials and labour.
ix. Connecting pipes to sanitary fixtures and appliances.
x. Standard and special pipe fixing arrangement where necessary fittings, supporting
clips,saddles,brackets, holder bats straps etc.
xi. All builders works such as chasing and forming holes through brick work/ blockwork/
foundations and concrete slabs beams columns floor slabs manholes and like and making
good all damages.
xii. Testing and disaffection after completion.
b. Rates for sanitary fittings shall include for
i. Fittings such as taps, waste water outlet, flushing cistern, internal overflows and the like and
supporting brackets, incidental materials for fixing.
ii. Assembling, jointing together, fixing components parts and jointing to pipes including
necessary coupling and for leaving perfectly clean undamaged and in perfect working order
as on completion.
c. Jointing and or connecting pipes to sanitary fittings.

Any special water supply and drainage fittings such as bends, tees, reducers etc. unless
otherwise specified separately in the Bill of Quantities, shall be deemed to have been
included in the relevant items and such items should accordingly be rated to include for
such specials etc. and for any extra work involved and the satisfactory completion of such
items.
Where pipes pass through walls or slabs these shall be wrapped with a layer of inert
materials. For pipes exceeding 50 mm dia sleeve pipes shall be used for the full thickness
of slabs, walls or beams through which the pipes pass.
DRAINAGE WORK
a. The provisions and the clauses of precedence trades shall equally apply to relevant item of
this trade.
b. The rates for trench excavation for pipes shall include for depending and widening the
trench as necessary to enable the barrels of pipes of rest on firm and to facilitate jointing.
c. The rates for rock excavation in trench excavations shall include for importing selected
materials to replace any excavated rock which is unsuitable for back filling and for all
additional rock excavation and appropriate filling beyond the maximum measurable in
accordance with the specification.
d. The rates for concrete beds and surrounds to pipes shall include for flexible joints and any
necessary formwork where required by the specification.
15. ELECTRICAL INSTALLATIONS
a. The execution of Electrical Installation shall every respect comply with the current
Regulations of the Institute of Electrical Engineers, London, requirements of Ceylon
Electricity Board and the area Authority.
b. The rates for equipment and control area, distribution boards, meters, switches, fuses, etc.
shall include for connecting up, fixings and supports for the complete installation and for
suitable mounting boards, frames, supports, housings and cabinets where required.
c. The rates for cables, tape, bus-bar trunking etc. (except where included in sub circuits or
electrical points) and the like shall include for joints in the running length, all allowances for
sagging snaking, for drawings through conduits,laying in trunking of surface fixing where
retired with cable supports, clears, hangers, channels, insulators and the like.
d. i. The rates for cables and the like laid in benches shall include for drawing through conduits
or ducts where required.
ii. The rates for cable terminations shall include for all connections point boxes, insulating and
jointing materials, cable terminations glands, lock nuts, bushes and the like.

e. i. The rates for conduits trunking cable tray etc. (except where included in sub circuits of
electrical points) and the like shall include for all short lengths, joints and couplers in the
running length, and for all fixings and supports with approved saddles, crumpets, clips and
the like cut and pinned, built-in or plugged and screwed to walls or ceilings including
chasing brick work, block work, concrete slab beams walls columns and the like and make
good.
ii. The rates for conduits and the like shall include for all bends, tees, socket and the
like,cutting, screwing, threading, jointing and providing all conduit boxes, junction boxes and
the like.
f. The rates for the installation of sub main circuits, lighting points switched points, socket
outlets, fused spur outlets, isolators, etc. (other than those applicable to the distribution
switch gear) shall include where applicable, for all conduit, trunking, cable tray, cabling,
terminations, fixings and connections from the distribution
switched gear to and including the point (accessories measured separately) and shall be
deemed to include for any item mentioned in the Electrical installation Specification but not
shown on the drawings and vice-versa.
g. The rates for lighting fittings, fittings such as ceiling fans and extract fans, and for
appliances such as air- conditioning units shall include for assembly, fixing and connection
from the spur outlet or isolator to the fitting or appliance with all necessary additional wiring
earthing and outlet roses and leaving perfectly clean and undamaged on completion.
h. The rates for fixing only fittings and appliances provided by the employer should include in
addition to the foregoing for accepting delivery, storing and handling the fittings and
providing any additional materials and internal wiring.
j. The rates for connections only to fittings and appliances such as pumps, water heaters, air
conditioning units and extract fans shall include for connection from the isolator or spur
outlet to the fitting or appliance (these being measured separately) , with all necessary
additional wiring, earthing and outlet roses.
k. The rates for power outlets shall include for mounting boxes and frames.
l. The rates for power switched with remote outlets shall include for the additional outlet plates
and boxes.
m. The rates for switched socket outlets shall include for 1 No fused plug top and 4 No fuse
links.
n. The preceding preambles shall apply equally to auxiliary installations such as TV

installations, telephone installations, and bell signal systems.
o. Painting of timber work and metal work.
p. If the items of electrical installation are measured as sub circuit point wiring or in electrical
points, the rates for such items shall include for :
i. The preceding clauses of this trade where relevant.
ii. Preparation of asbuilt drawings to be submitted to Employer at the handing

over/ practical completion.
iii. All items and accessories required for proper installation as per specification and
regulation up to load point and labour connected therewith.
iv. All wiring, conduiting and cables and labour connected therewith if not measured
separately.
v. Items specified in the specification but not shown in the drawings.
vi. Disconnecting and refixing of electrical fitting and appliances as required for the
convenience of other trades.
vii. Painting of timber work metal work executed under this trade.
q. Rate to include submission of Megar Test report of the building Elactrical Installation from
Charted Elactrical Engineer


for
Department of Buildings (Metric Version)
Item Basic Rate

Item Description Unit
Code 2020
C - DEMOLISHER
C001 Demolishing brickwork in cement stacking brick and clearing debris away
m3 802
C002 Demolishing brickwork in lime stacking brick and clearing debris away 3
m 1,068
C003 Removing existing Ceiling, stacking materials and clearing debris away. 2
m 104
C004 Demolishing Cement mass concrete in floors of 150mm thick, and clearing
debris away. m3 4,767
C005 Demolishing reinforced cement concrete in suspended floors of 100mm thick,
removing reinforcement and clearing debris away. m2 1,049
C006 Removing and stacking corrugated sheets, G.I., asbestos or Zn/Al from roof , or
walls and clearing debris away. m2 113
C007 Removing and stacking Door or Window, size upto 3.75 m2 from existing walls
Nos 1,350
C008 Removing and stacking Door or Window, size over 3.75 m2 from existing walls
Nos 1,130
C009 Removing and stacking Door or Window, sash only up to 3.75 m2 from existing
walls Nos 196
C010 Demolishing floors brick paved, 100mm thick and clearing debris away. m2 121
C011 Demolishing rubble masonry in cement, stacking rubble and clearing debris
away. m3 1,470
C012 Removing and stacking tiles Calicut or half round, from roof of single storeyed
buildings and clearing debris away. m2 81
Transporting debris
C013 Transporting debris cleared away from site by tractor (app 16Km away). Rate to
include loading & unloading. Load 4,515
C-1 This BSR is for Construction works only.

Item Basic Rate

Code 2020
D - EARTH WORK
Site Clearing
D001 Clearing site vegetation including removal of bushes, shrub under growth hedges
and tree stumps upto 300mm girth measured at height upto 1.0 m above ground
level ,removing rubbish upto a distance of 50m beyond the outer walls of the
proposed building. m2 24
Removing Trees
D002 Removing trees and stumps size of girth varies from 300mm and upto 600mm
and girths are measured at 1.0 m height above ground level including cutting of
trunks and branches, grubbing up roots, staking of serviceable materials and
disposal of unserviceable materials.( aveg. 150mm dia. and aveg. ht 3.0m)
Nos 1,522
D003 Removing trees and stumps size of girth varies beyond 600mm and upto
1200mm and girths are measured at 1.0 m height above ground level including
cutting of trunks and branches, grubbing up roots, staking of serviceable
materials and disposal of unserviceable materials.(aveg. 300mm dia. and aveg. ht
4.5m) Nos 4,600
D004 Removing trees and stumps size of girth varies beyond 1.2m and upto 2.4m and
girths are measured at 1.0 m height above ground level including cutting of
trunks and branches, grubbing up roots, staking of serviceable materials and
disposal of unserviceable materials.( aveg. 600mm dia. and aveg. ht.7.0m)
Nos 15,450
D005 Removing trees and stumps size of girth varies beyond 2.4m and girths are
measured at 1.0 m height above ground level including cutting of trunks and
branches, grubbing up roots, staking of serviceable materials and disposal of
unserviceable materials.( aveg. 1.0m dia. and aveg. ht.10.0m)
Nos 30,900
Removing Top Soil
D006 Removing top soil to a depth not exceeding 150mm & depositing as directed
within site m2 162
Excavation
D007 Excavation over site to reduce level in any material except rock requiring blasting
including depositing and levelling as directed upto a distance not exceeding
10.0m m3 861
D008 Excavation in trenches for walls/column pits in soft/loose soil from 0 to 1.5 m
deep and depositing excavated material to a distance not exceeding 10.0m .
(Earth work support to be paid separately). m3 530
D009 Excavation in trenches for walls/column pits in ordinary soil from 0 to 1.5 m
(Earth work support to be paid separately). m3 1,192
D010 Excavation in trenches for walls/column pits in hard dense soil from 0 to 1.5 m
(Earth work support to be paid separately). m3 1,854
D-1 This BSR is for Construction works only

Item Basic Rate

Code 2020
D011 Excavation in trenches for walls/column pits in mud/wet soil from 0 to 1.5 m
deep and depositing excavated material to a distance not exceeding 10.0m . (earth
work support to be paid separately). m3 1,589
D012 Excavation in trenches for walls/column pits in soft disintegrated rock (not
requiring blasting) up to a depth of 1.5 m and depositing excavated material to a
distance not exceeding 10.0m . (earth work support to be paid separately).
m3 1,324
D013 Excavation in trenches for walls/column pits in hard rock requiring blasting up to
a depth of 1.5 m and depositing excavated material to a distance not exceeding
10.0m . (earth work support to be paid separately).
m3 1,895
D014 Benching rock in foundation in 1.0m steps.(Blasting prohibited) 2
m 4,642
Earthwork-backfilling
D015 Backfilling in 150mm layers & compacting pits and trenches with available earth
m3 530
D016 Backfilling in 150mm layers & compacting pits and trenches with imported earth.
m3 2,235
D017 Filling under floors including levelling watering and compacting in 150mm
layers with selected earth available at site m3 1,059
D018 Filling under floors including levelling watering and compacting in 150mm
layers with imported earth. m3 2,765
D019 Sand filling in Column footing, wall under foundations, watered and well
rammed. m3 6,939
D020 Supplying, spreading, levelling, watering, Graded Quarry dust (4.5mm
downward) in 225mm thick layers and compaction using machine
Rammer.(loose volume). Rate include hire charges of the machine rammer. m3 3,825
Earth work support
D021 Earth work support (open planking ) in trenches upto a depth of 1.5m.
m2 1,104
D022 Earth work support (close planking ) in trenches upto a depth of 1.5m. m2 1,662
D023 Earth work support (close planking ) in deep excavation in trenches upto 5m
depth. m2 1,854
Anti-termite Treatment
D024
Anti-termite treatment for the new construction with applying Biflex 10Tc or
approved equivalent as per manufacturer's specification including horizontal &
vertical barriers with 10 years warranty on application.
m2 291
D-2 This BSR is for Construction works only

Item Basic Rate

Code 2020
F - CONCRETE
(Reinforcement and shuttering paid for separately)
Mixing Concrete (Excluding Placing)(In-Situ Concrete)
F001 Mixing concrete 1:3:6 (40mm) using mixer m3 11,622
F002 Mixing concrete 1:2½:5 (25mm) using mixer 3
m 12,561
F003 Mixing concrete 1:2:4 (20mm) using mixer 3
m 13,579
F004 Mixing concrete 1: 1½ :3 (20mm) using mixer 3
m 14,760
F005 Mixing concrete 1: 1: 2 (20mm) using mixer 3
m 18,056
Mass Concrete ( Including Placing)
Site Mixed Concrete 1:3:6 (40mm) -(Gr.15 Mix)
In Foundation
F006 50mm thick cement concrete 1:3:6(40mm) screed in foundation at depths Not
exceeding 1.5 m. m2 697
F007 50mm thick cement concrete 1:3:6(40mm) screed in foundation at depths
Exceeding 1.5 m & upto 3.0m m2 724
F008 75mm thick cement concrete 1:3:6(40mm) screed in foundation at depths Not
exceeding 1.5 m. m2 1,032
F009 75mm thick cement concrete 1:3:6(40mm) screed in foundation at depths
Exceeding 1.5 m & upto 3.0m m2 1,073
Site Mixed Concrete 1:2:4 (20mm)-(Gr.20 Mix)
In Foundations
F010 75mm thick cement concrete 1:2:4 (20mm) in foundation at depths Not
exceeding 1.5 m. m2 1,181
F011 75mm thick cement concrete 1:2:4 (20mm) in foundation at depths Exceeding
1.5 m & upto 3.0m m2 1,222
F012 150mm thick cement concrete 1:2:4 (20mm) floor (mass concrete)
m2 2,503
Reinforced Concrete ( Including Placing)
Site Mixed Concrete 1:2:4(20mm)-Grade 'C - 20'
In Column shafts/Walls- upto 1st floor level
F013 Cement concrete with 1:2:4 (20mm), in 113mmx150mm column in ground floor.
m 420
F014 Cement concrete with 1:2:4 (20mm), & 150mmx150mm Columns in ground
floor m 545
F015 Cement concrete with 1:2:4 (20mm) ,& 225mmx225mm Columns in ground
floor m 1,195
F016 Cement concrete 1:2:4(20mm) & 300mmx300mm Column shafts in ground
floor, using mixer and vibrator.
m 2,043
F017 Cement concrete with 1:2:4(20mm), in 350mmx350mm column in ground floor
m 2,553
F018 Cement concrete with 1:2:4 (20mm),225mmx150mm beam upto 1st floor level
m 819
m 1,261
F-1 This BSR is for Construction works only

Item Basic Rate

Code 2020
m 1,785
In Floor Slabs
F021 125mm thick R.C.C. floor slab with 1:2:4 (20mm), in 1st floor, rate inclusive of
placing vibrating and curing. m2 2,413
F022 150mm thick R.C.C. floor slab with 1:2:4 (20mm) ,in 1st floor, rate inclusive of
placing vibrating and curing. m2 2,881
In Lintols
F023 Cement concrete with 1:2:4 (20mm), in 113mmx150mm lintols in ground floor
m 434
F024 Cement concrete with 1:2:4 (20mm), in 225mmx225mm lintols in ground floor m 1,254
F025 Cement concrete with 1:2:4 (20mm), in 225mmx300mm lintols in ground floor
m 1,664
F026 Cement concrete with 1:2:4 (20mm), in 300mmx375mm, lintols in ground floor m 2,738
Site Mixed Concrete 1:1½:3(20mm)-Grade 'C - 25'
In Floors
F027 150 mm thick cement concrete 1: 1½ :3 (20mm)Ground floor (mass concrete),
rate inclusive of placing. m2 2,683
F028 125mm thick R.C.C. floor slab with 1:1½ :3 (20mm) ,in 1st floor, rate inclusive
of placing and curing. m2 2,563
F029 150mm thick R.C.C. floor slab with 1:1½:3 (20mm), in 1st floor, rate inclusive
of placing and curing. m2 3,061
In Column shafts
F030 Cement concrete with 1: 1½ :3 (20mm),in 150mmx150mm columns in ground
floor. m 574
F031 Cement concrete with 1: 1½ :3 (20mm), in 225mmx225mm column in ground
floor 1: 1½ :3 (20mm) m 1,256
floor m 2,153
floor m 2,693
In Beams
F034 Cement concrete with 1: 1½ :3 (20mm) ,150mmx150mm beam upto 1st floor
level. m 568
F035 Cement concrete with 1:1½:3 (20mm),225mmx150mm beam upto 1st floor level.
m 861
F036 Cement concrete with 1:1½:3 (20mm),225mmx225mm beam upto 1st floor level
m 1,323
F037 Cement concrete with 1:1½:3 (20mm),225mmx300mm beam upto 1st floor level
m 1,867
In Lintols
F038 Cement concrete with 1:1½:3 (20mm), in 113mmx150mm lintols in ground floor
m 454
F039 Cement concrete with 1:1½:3 (20mm) , & 225mmx225mm lintols in ground
floor m 1,315

Item Basic Rate

Code 2020
F040 Cement concrete with 1:1½:3 (20mm) , & 225mmx300mm lintols in ground
floor m 1,747
F041 Cement concrete with 1:1½:3 (20mm) ,in 300mmx 375mm lintols in ground
floor m 2,875
Ready mixed Concrete
F042 Supplying and laying Ready Mixed concrete Grade 20 (First floor slab).. m3 18,965
F043 Supplying and laying Ready Mixed concrete Grade 25 (First floor slab). 3
m 19,280
F044 Hiring charges for concrete pump Truck ( Up to 30m3) Item 25,093
F045 Hiring charges for concrete pump Truck ( For every 1m3 above 30m3)
m3 756
Timber Formwork
Form work (For Column in ground floor)
F046 Sawn timber formwork to 225mmx225mm cement concrete column in ground
floor including making mould, assembling ,dismantling ,cleaning and repairing
after use. m2 2,073
Form work (Untreated Non-structural Category A)
F047 Shuttering for floor slab concrete including 100mmx50mm (untreated non-
structural category A) timber joists and necessary props. upto 3.6m height.
(Rate to include for dismantling same when required). m2 1,825
F048 Shuttering for column shaft 225mm x 225mm including (untreated non-structural
category A) timber joists and necessary props etc. (Rate to include for
dismantling same when required) 2
m 2,257
F049 Shuttering for beam sides & soffit in (untreated non-structural category A)
timber, joists and necessary props etc. (Rate to include for dismantling same
when required) m2 1,502
20mm thick plywood form work
F050 20mm thick plywood form work for concrete beams in ground floor consider 225
mmx 300 mm beam to 6 m, long contact area 5 m2. m2 2,681
F051 Supplying and fixing 20mm thick plywood form work in column ground floor
consider area 1.4 m2. ( 1.5 m high 225 mmx 225 mm column. ) m2 2,180
F052 Supplying and fixing 20mm thick plywood timber formwork for underside of fist
floor slab. consider 6m x 3m area - 18 m2. m2 2,392
Sawn timber formwork
F053 Sawn timber formwork for concrete beam in ground floor including timber joist
and necessary props (Rate to include for dismanteling same when required).
m2 1,414
F054 Sawn timber formwork for underside of first floor slab including timber joist and
necessary props (Rate to include for dismanteling same when required).
m2 1,625

Item Basic Rate

Code 2020
Reinforcement
F055 Tor steel reinforcement to slabs, beams, columns or lintols bent to shape laid in
position and tied with G I wire as directed Mt 249,988
F056 Tor steel rods in foundation bending to shape, laying in position and tying with
G.I wire as directed. Mt 220,511
F057 Mild steel reinforcement to slabs, beams, columns or lintols bent to shape laid in
position and tied with G I wire as directed Mt 260,638

Item Basic Rate

Code 2020
G-MASONRY WORK
Brick Work and Block Work
Brick Work
G001 Brick work in cement sand 1:5 in foundation upto D P C m3 15,814
G002 Brick work in cement sand 1:8 in foundation upto D P C 3
m 15,672
G003 Brick work in cement sand 1:5 in 112.5mm (4½") thick walls in ground floor
m2 1,979
G004 225mm (9") thick brick wall cement sand 1:5 in superstructure/ walls in ground
floor m2 3,700
G005 Brick work 350mm (13½") thick in cement sand 1:5 in superstructure in ground
floor m2 5,542
G006 225mm (9") thick brick wall cement sand 1:8 in superstructure/walls in in
ground floor m2 3,628
G007 112.5mm (4½") thick brick wall (wire cut) in cement sand 1:5 in ground floor 2
m 2,790
G008 225mm (9") thick in cement and sand 1:5 with wire cut brick 2
m 5,244
G009 Extra over for facing including raised pointing 3mm thick in cement sand 1:1
mixture in ground floor m2 1,665
G010 75mm thick floor paved in lime mortar 2:5 in ground floor 2
m 1,666
G011 75mm thick floor paved in cement mortar 1:8 in ground floor 2
m 1,602
G012 Steps 338mm x150mm in brick in cement and sand 1:5 with 16mm thick cement
and sand 1:2 rendering including necessary excavation m 1,653
Hollow block masonry
G013 100mm thick Hollow block masonry in cement and sand mortar 1:5 with cavities
unfilled in ground floor.3.0mx3.0m area ( size of each block
400mmx200mmx100mm) (Min com/st 3.0 N/mm2 ) m2 1,462
G014 150mm thick hollow block work in cement and sand mortar 1:5 with cavities
unfilled in ground floor.3.0mx3.0m area ( size of each block
400mmx200mmx150mm) (Min com/st 3.0 N/mm2 ) m2 1,854
G015 200mm thick Hollow block masonry in cement and sand mortar 1:5 with cavities
unfilled in ground floor. 3.0mx3.0m area ( size of each block
2
400mmx200mmx200mm) (Min com/st 3.0 N/mm2 ) m 2,437
Solid block masonry
G016 100mm thick solid block masonry in cement and sand mortar 1:5 in ground floor.
3.0mx3.0m area ( size of each block 400mmx200mmx100mm) (Min com/st 3.0
N/mm2 ) m2 1,679
G017 150mm thick solid block masonry in cement and sand mortar 1:5 in ground
floor.3.0mx3.0m area ( size of each block 400mmx200mmx150mm) (Min
com/st 3.0 N/mm2 ) m2 2,262
G018 200mm thick solid block masonry in cement and sand mortar 1:5 in ground floor.
3.0mx3.0m area ( size of each block 400mmx200mmx200mm) (Min com/st 3.0
N/mm2 ) m2 2,870
G-1 This BSR is for construction works only

Item Basic Rate

Code 2020
Stone Work
G019 Random rubble (150mm-250mm) masonry in cement mortar 1:5 in foundation m3 11,652
G020 Random rubble (150mm-250mm) masonry in cement mortar 1:5 in
superstructure m3 12,535
Paste rubble
G021 Supplying & Laying pointed (50mm-75mm thick ) or Paste rubble masonry in
cement and sand 1:2 in ground Floor.(Including hire chargers of Grinder)
m2 7,651
G-2 This BSR is for construction works only

Item Basic Rate

Code 2020
H-WATER PROOFING
H001 20mm thick DPC in cement sand 1:2 finished with 2 coats hot tar and blinded
with sand 2
m 1,177
H002 Concrete waterproofing treatment by using Crystallization technology according
to Manufacturers specification's. ("Xypex" or equivalent approved product
including preparation of surface) m2 2,156
H003 Waterproofing treatment using cement based, micro-porous (breathing), coating
according to Manufacturers Specifications. ("Thoroseal" or equivalent approved
product including preparation of surface), m2 1,616
H004 Waterproofing treatment by using flexible polymer cement slurry according to
Manufacturers specification's. ("Masterseal 540"(Barralastic) or equivalent
approved product including preparation of surface) m2 1,023
H005 Waterproofing and crack isolation membrane type treatment to slab (area less
than 300m2) according to Manufacturers specification's. ("Mapelastic" or
equivalent approved product including preparation of surface)
m2 1,776
H006 Waterproofing treatment to external walls by using acrylic elastomeric high
flexible bituminous coating according to Manufacturers specification's.
("Synroof" or equivalent approved product including preparation of surface)
m2 1,001
H007 Supply & Laying Gauge 750 Polythene damp proof membrane with 150mm laps
laid under floors.
m2 132
H-1 This BSR is for Construction works only

Item Basic Rate

Code 2020
J-STRUCTURAL METAL WORKS

"C" channel
J001 Supplying & Fixing of a structural steel channel purlin 127mm x 64mm (14.9
Kg/m) fixed as a purlin on roof trusses / roof beams with necessary bolts/cleat
connecting arrangement (Cleats and Bolts Paid separately). Rate shall include for
applying two coats of enamel paint ( C.I.C. or equivalent ) after treating with a
coat of anticorrosive paint to all exposed faces of purlin.
m 1,143
Wire mesh
J002 Wire netting, hexagonal mesh 12mm supplying and fixing (beading to be paid for
separately) m2 666
Weld mesh
J003 50mmx50mm Weld mesh No.12, supplying and fixing to existing frames with
staples (fillets and beadings to be paid for separately) m2 1,380
J004 50mm x 50mm Weld mesh No.10 supplying and fixing to window frames with
50mm x 12mm (Group 2) timber beadings, and painting weld mesh with 2 coats
anti-corrosive paint, and beadings with primer, undercoat and 2 coats enamel
paint to approved. Rate to include for making openings for bolts, casement stays
etc.
m2 4,341
J005 50mmx50mm Weld mesh No.12 supplying and fixing to window frames with
50mm x 12mm (Group 2) timber beading, and painting weld mesh with 2 coats
anti-corrosive paint, and beadings with primer, undercoat and 2 coats enamel
paint to approved tint Rate to include for making openings for bolts, casement
stays etc. m2 3,886
0 0
Web Truss - (Angle between 15 - 45 )
J006 Fabricating & Fixing Steel web Truss , Span less than 8m consist of
38mmx38mmx6mm top chord and bottom chord with 16mm mild steel bracings.
Including all , gusset plates , cleats , rivets , nuts, washers, rag bolts,
separators etc.. (Rate shall include for painting of two coats of anticorrosive paint
& one coat of enamel paint.) (Hoisting charges paid separately)
Kg 360
J-1 This BSR is for construction works only

Item Basic Rate

Code 2020
K-METAL WORK
Aluminium
** Aluminium window **
70mm (1.2mm thick) Aluminium Casement Double Sash Window
Supplying, Fabricating & Installing of 1.2mm thick 70mm deep double sashed
Aluminium Casement window frame and 1.2mm thick 40mm X 35mm (depth)
window sashes . Rate to include for 5mm thick glass pans, EPDM rubber
beadings, weather strips, casement locks, Hinges, rawl plugs, fasteners & etc.
(Alumex extrusion Nos. CA-2005, CA 1011 & CA 1012 or equivalent)
K001 -DO- Matt Finished Aluminium m2 15,142

K002 -DO- Natural Anodized Aluminium 2
m 16,046
K003 -DO- Bronzed Anodized Aluminium 2
m 16,179
K004 -DO-Powder Coated Aluminium 2
m 17,316
K005 -DO-Wood Finished Aluminium 2
m 21,295
70mm (1.2mm thick) Aluminium Casement Double Sash Window with Top
Fixed Panel
Supplying, Fabricating & Installing of 1.2mm thick 70mm deep double sashed
Aluminium Casement window frame and 1.2mm thick 40mm X 35mm (depth)
window sashes with fixed glass panels on top. Rate to include for 5mm thick
glass pans, EPDM rubber beadings, weather strips, casement locks, Hinges,
rawl plugs, fasteners & etc. (Alumex extrusion Nos. CA-2005, CA 1011 & CA
1012 or equivalent)
m 14,626
m 17,290
m 15,777
m 19,655
1.3mm thick 70mm Double Sashed Aluminium Sliding window
Supplying, Fabricating & Fixing Aluminium window with 1.3mm thick ,70mm
depth Aluminium framed (max. width 32.0mm) Double sash(max. width
36.2mm)Sliding Window including 5mm clear glass pans, necessary/ EPDM
rubber beadings, sliding lock etc. (Alumex extrusion No. 70S-1001, 70S-1201-1,
70S-1101-1, 70S-1401, 70S-1501, 70S-1601, 70S-1701 & etc. or equivalent)

K012 -DO- Natural Anodized Aluminium
m2 8,167
K013 -DO- Bronzed Anodized Aluminium m
2
8,262
K014 -DO-Powder Coated Aluminium m 2
8,684
K015 -DO-Wood Finished Aluminium m 2
10,243
K-1 This BSR is for construction works only

Item Basic Rate

Code 2020
1.3mm thick 70mm Double Sashed Aluminium Sliding window with 2 Fixed
Panels at Top or Bottom
Supplying, Fabricating & Fixing Aluminium Window with 1.3mm thick ,70mm
depth Aluminium Framed (max. width 61.0mm) Double sash (max. width
56.2mm) Sliding Window with Two fixed panels on top or bottom including
5mm clear glass pans, necessary/EPDM beadings, sliding lock etc.(Alumex
extrusion No. 70S-1012, 70S-1201-1, 70S-1101-1, 70S-1401, 70S-1501, 70S-
1601, 70S-1701 & etc. or equivalent)
m 8,818
m 8,917
m 9,807
m 10,968
1.3mm thick 70mm 4 Sashed Aluminium Sliding window with 4 Sliding
Panels at Top or Bottom
depth Aluminium Framed (max. width 60.0mm) Four Sliding Sashes(max. width
30.0mm) with Four Sliding panels on Top or Bottom including 5mm thick clear
glass pans, necessary/EPDM beadings, sliding locks etc.(Alumex extrusion No.
70S-1201-1, 70S-1001-1, 70S-1006, 70S-1914, 70S-1401, 70S-1501, 70S-1601,
70S-1701 & etc. or equivalent)
m 8,690
m 8,790
m 9,257
m 10,769
1.5mm thick 80mm 6 Sashed Aluminium Sliding window
depth Aluminium Framed (max. width 37.6mm) Six Sashes Sliding
Window(max. width 63.0mm) including 5mm clear glass pans, necessary/EPDM
beadings, sliding lock etc. (Alumex extrusion No. 80S-2001, 80SFL-1001, 80S-
2201, 80S-2301, 80S-2101, 80S-2501, 80S-2601, 80S-2701, 80S-2101 & etc. or
equivalent)
m 11,422
m 11,550
m 12,395
m 14,763

Item Basic Rate

Code 2020
Fixed glass Windows

70mm (1.2mm thick) Aluminium Fixed Glass Window
Supplying, Fabricating & Installing of 1.2mm thick 70mm deep Aluminium fixed
glass window with 5mm thick clear glass pan. Rate to include for rubber/EPDM
beadings, rawl plugs, fasteners etc. (Alumex extrusion Nos. CA 1011 & CA
1012 or equivalent)
m 8,199
m 8,242
K034 -DO-Powder Coated Aluminium m2 8,942
m 11,792
Aluminium doors
1.6mm thick Aluminium 100mm double door
Supplying, Fabricating and Installing of Aluminium Double sashed 100mm door
with 5mm thick glass pans. Rate inclusive of necessary fasteners suitable wool
felt and hinges (Union or equivalent 102x76x2 mm) etc.(Door closers, door
locks and door handles paid separately)
K037 -DO- Natural Anodized Aluminium m2 15,457
m 15,649
m 16,855
K040 -DO-Wood Finished Aluminium m2 20,743
1.6mm thick Aluminium 100mm single door
Supplying, Fabricating and Installing of Aluminium Single sashed 100mm door
with 5mm thick glass pans. Rate inclusive of necessary fasteners, wool felt and
hinges (Union or equivalent 102x76x2 mm) etc.(Door closers, door locks and
door handles paid separately)
K042 -DO- Natural Anodized Aluminium m2 19,074
K043 -DO- Bronzed Anodized Aluminium m2 19,323
K045 -DO-Wood Finished Aluminium m2 26,098
Aluminium Sliding Door
80mm (1.5 mm thick) Aluminium Sliding Door
Supplying, Fabricating and Installing 1.5mm thick 33.7mmX80mm (depth)
Aluminium framed two sliding door sashes with 5mm thick glass pans,
suitable/EPDM rubber beadings, necessary fastners, rollers & etc.(door locks and
door handles paid separately) (Alumex extrusion Nos. 80S-2001, 80S-2002,
80S2101 and etc. or equivalent)
m 11,495
m 11,627
Item Basic Rate

Code 2020

m 15,356
100mm (1.5 mm thick) Aluminium Sliding Door
Supplying, Fabricating and Installing 1.5mm thick 30mmX98mm (depth)
Aluminium framed one half fixed & Single Sliding Door sash with 5mm thick
glass, suitable/EPDM rubber beadings, necessary fastners, rollers & etc. (Door
closers, door locks and door handles paid separately) (Alumex extrusion Nos.
SD-1001, DS-1101, SD1501 and etc. or equivalent)
m 11,763
m 11,911
m 13,974
m 15,359
100mm (1.5 mm thick) Aluminium Sliding Door with top fixed panel
Aluminium framed one half fixed & Single Sliding Door sash with top fixed
panels. Rate to include for 5mm glass pans, suitable/EPDM rubber beadings,
necessary fastners, rollers & etc.(Door closers, door locks and door handles paid
separately) (Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or
equivalent)
K056 -DO- Matt Finished Aluminium 2
m 12,325
m 12,538
m 12,570
m 13,701
m 16,714
100mm (1.6 mm thick) Aluminium 3 track Sliding Door
Aluminium framed one half fixed & Single Sliding Door sash with top fixed
panels. Rate to include for 5mm glass pans, suitable rubber beadings, necessary
fastners, rollers & etc.(Door closers, door locks and door handles paid separately)
(Alumex extrusion Nos. SD-1001, DS-1101, SD1501 and etc. or equivalent)

m 11,400
m 11,735
m 12,698
m 14,541

Item Basic Rate

Code 2020
Zn/Alu Roller door

K066 Supplying and fixing of a Zn/Alu Roller door, having a maximum clear width of
6.0m and consisting of 0.6mm thick Zn/Al covering sheet, center bar pulleys,
side plates with necessary racers, fabricating mechanical winding box with m.s
square tube and covering the box with metallic sheets, fixing on site with bottom
bars and G.I, u-channels for vertical guides at two vertical edges, which are
painted with two coats of anticorrosive paint and two coats of enamel paint to
match the colour of door sheeting, and sound reduction rubber beading
embedded in the guide bars. Pulling rod and chain to be provided for manual
rolling operation. (Additional length of 225mm to two sides horizontally and
450mm to upper end inside the mechanical box as initial winding vertically to be
added to the clear opening area).
m2 6,910
Roller door motor
K067 Suppling roller shutter door moter, 0.5Hp, 300w, 2.5A sing-phase, 1780 rpm and
54:1 gear ratio, with two remote controllers for auto operation.
Nos 32,025

Item Basic Rate

Code 2020
L-WOOD WORK
L1-Carpentry
L001 Prepare and apply two coat of Wood preservative (clear type) to structural timber
including touching up out ends etc. after fixing m2 210
Timber treatment
L002 Structural Timber treated by Vacuum Pressure Impregnation Technique with
approved wood preservatives such as CCB that are registered by register of
pesticides, for protection against wood destroying agents such as wood bores,
fungi and termites. (Execution according to the Manufacturers specifications) (By
"Finlay Celurised treated " or equivalent system)
m3 16,209
L003 Reepers 50mm x25mm in (Group3, Category A) timber supplying and fixing
with iron nails, upto 30m (Shifting of tiles to be paid for separately) m 196
L004 Supply and fixing 50mm x50mm (Group3,Category A) timber Battons in roof
work, with nails over 30m. m 413
L005 Supply and fixing 100mm x50mm (Group3,Category A) timber rafters for roof
work. m 879
L006 Supply and fixing 175mm x50mm (Group3,Category A) timber ridge plate in
roof work. m 1,756
L007 Supply and fixing 100mm x75mm (Group3,Category A) timber wall plate in
roof work. m 1,425
L008 Supply and fixing 125mm x75mm (Group3,Category A) timber perlin in roof
work. m 1,783
L009 Supply and fixing 100mm x75mm (Group3,Category A) timber Struts, upto
1800mm height in roof structure, including forming necessary Timber joints at
both ends.600mm Timber bearer provided at Bottom. m 2,073
L010 Class 1 timber frame work for Calicut pattern tile hip roof in single storey
building consisting of wall plate beam ridge plate rafters etc.. (Preservative
treatment to be measured separately) m2 3,790
L011 Cclass 1 timber frame work for corrugated asbestos sheet roof in single storeyed
building m2 2,246
L2-Joinary
Boards, barge, valance, fascia
L012 Boards, barge, valance, fascia, 200mm wide and 25mm thick in (Group
5,Category A), timber fixing complete with necessary screws new or renewing,
above .028 m3
m 1,025
5,Category A), timber supplying and fixing complete with necessary screws new
or renewing, upto .028 m3
m 1,066
5,Category B), timber supplying and fixing complete with necessary screws new
or renewing, above .028 m3
m 586
L-1 This BSR is for construction works only

Item Basic Rate

Code 2020
5,Category B), timber supplying and fixing complete with necessary screws new
or renewing, upto .028 m3
m 582
L016 20mmx225mm high Valance board in (Group 5,Category A), timber fixed with
brass screws to ends of rafters (For tile roofing)
m 1,299
L017 20mmx225mm high barge board in (Group 5,Category A), timber fixed with
brass screws at 600mm centers to sides of rafters
m 1,294
Ceiling / Partition
L018 Ceiling, asbestos, flat fixing with clout headed nails to 100mm x 50mm joists and
50mm bearers of (Group 4,Category A) timber including 37.5mm x 12mm cover
fillets and 62.5mm x 37.5mm coves of Halmilla timber. Rate to include 2 coats
of wood preservatives to joists and bearers. Primer undercoating and two coats of
emulsion paint to Asbestos sheets. m2 4,579
L019 Flat asbestos horizontal eaves ceiling comprising 50mm x 50mm bearers
in(Group 4,Category A) timber asbestos sheet supplied and fixed with beadings
& cove moulding, rate to include for applying wood preservative to timber frame,
two coats enamel paint for beadings, and two coats emulsion paint for asbestos
ceiling. m2 3,636
L020 Ceiling or partition, Lunumidella, 12mm planning, lapping and nailing to existing
frames or underside of rafters, above 9.3m2 (Fillets and beadings paid for
2
separately) m 1,355
L021 Ceiling or partition, Lunumidella, 12mm planning, lapping and nailing to existing
frames or underside of rafters, upto 9.3 m2 (Fillets and beadings paid for
separately) m2 1,452
L022 Ceiling or partition, Lunumidella, 12mm beading and rebating, nailing to
underside of existing joists, rafters or frames, above one square (Fillets and
beadings, paid for separately) m2 1,209
L023 Ceiling or partition, Lunumidella, 16mm beading and rebating, nailing to
underside of existing joists, rafters or frames, upto one square (Fillets and
beadings, paid for separately) m2 1,495
L024 Ceiling openings 600mm x 450mm approx., forming complete with 50mm x
50mm bearers. (Glass tiles or sheets paid for separately) Nos 2,536
L025 Ceiling Lunumidella 12mm planks lapping and nailing to framework consisting
of 100mm x 50mm joists and 50mm x 50mm bearers in (Group 4,Category A)
timber, Rate to include for 2 coats of tar nap to joists and bearers. m2 4,297
L026 Ceiling Lunumidella 20mm thick planks lapping and nailing to framework
consisting of 100mm x 50mm joists and 50mm x 50mm bearers in (Group
4,Category A) timber, Rate to include for 2 coats of tar nap to joists and bearers.
m2 4,521
Beading
L027 Beading, Burma Teak, 37.5mm to 50mm x 12mm plain chamfering, supplying
and fixing complete with brass screws. m 451
L028 Beading, Burma Teak, 25mm x 20mm plain chamfering, supplying and fixing
complete with brass screws. m 375

Item Basic Rate

Code 2020
L029 Beading, Alstonia or local timber 37.5mm to 50mm x 12mm plain chamfering,
supplying and fixing complete with brass screws. m 137
L030 Beading, Halmilla, 37.5mm to 50mm x 12mm, plain chamfering, supplying and
fixing complete with brass screws. m 274
L031 Beading or filleting in Ginisapu or local timber for glass panes supplying and
fixing complete with brass springs or brass panel pins. m 137
Cove, mouldings
L032 Cove, mouldings, Alstonia or equivalent 62.5mm x 37.5mm fixing with brass
screws and plugs new or renewing. m 442
Fillets, quadrant
L033 Fillets, quadrant 20mm x 20mm supplying and fixing with springs or nails, in
(Group 6, Category A) timber. m 140
L034 Fillets, quadrant 25mm x 25mm in (Group 6, Category A) timber supplying and
fixing with springs or nails. m 151
Doors or Windows
L035 Doors or windows, ledging, bracing and battening with groove and tongue joints,
100mm x 75mm frames and 20mm to 22mm thick sashes in (Group 2,Category
A) local timber complete with brass furniture (Rim lock, Hinges). m2 17,453
L036 Doors or windows, ledging, bracing and battening with groove and tongue joints,
100mm x 75mm frames and 20mm to 22mm thick sashes in (Group 2,Category
B) local timber complete with brass furniture. m2 12,050
L037 Doors or windows, framing and battening, with 100mm x 75mm frames and
25mm to 28mm sashes in (Group 2,Category A) local timber complete with
brass furniture. m2 19,386
25mm to 28mm sashes in (Group 2,Category B) local timber complete with
32mm to 37.5mm sashes in (Group 2,Category A) local timber complete with
32mm to 37.5 mm sashes in (Group 2,CategoryB) local timber complete with
L041 Doors or Windows, framing and battening, sash only 25mm to 28mm thick in
(Group 2,Category A) timber supplying and fixing complete with available
furniture. m2 12,580
L042 Doors for garages, framing and battening in (Group 2,Category A) timber with
125mm x 100mm frames and 37.5mm thick sashes supplying and fixing
complete with iron pintoles and strap hinges. m2 13,051
L043 Doors or Windows, glazing and/or paneling with 100mm x 75mm frames and
28mm to 32mmsashes in (Group 2,Category A) local timber supplying and fixing
complete with brass furniture. m2 17,923

Item Basic Rate

Code 2020
L044 Doors or Windows, glazing and/or paneling with 100mm x 75mm frames and
28mm to 32mm sashes in (Group 2,Category B) local timber supplying and
fixing complete with brass furniture. m2 13,270
Door frame
L045 Door frame 100mm x 75mm in (Group 2,Category A) timber supplying & fixing
in position.
m 2,008
L046 Door frame 100mm x 50mm in (Group 2,Category B) timber supplying and
fixing in position.
m 1,026
Plywood Door ** Note:(Brand - MACKPY or equivalent)
L047 Door,32mm thick plywood ordinary (Moisture Resistant) single sash, size
825mmx 2025mm, hung on finished size 100mmx 75mm frame in (Group
2,Category A) timber and complete with brass furnitures. .(Door Lock paid
Separately) m2 11,011
L048 Door,32mm thick plywood ordinary (Moisture Resistant) single sash, size
825mmx 2025mm, hung on finished size 100mmx 75mm frame in (Group
2,Category B) timber and complete with brass furnitures. .(Door Lock paid
Separately) m2 9,574
L049 Supplying and fixing plywood door 32mm thick (Moisture Resistant) single
sash, size 825mmx 2025mm,hung to the existing frame including necessary
brass fittings.(Door Lock paid Separately) data 2ft 9"x6ft 9"=18.56s.ft 2
m 5,356
L050 Supplying & fixing 32mm thick Ply wood door, Both Side Luxury finish
(Moisture Resistant) ,size 825mmx 2025mm, single sash, hung to existing frame
including necessary brass fittings.(Door Lock paid Separately) data 2ft 9"x6ft
9"=18.56s.ft m2 7,313
Door PVC
L051 Door PVC supply and fixing to existing opening, (with out frame), Lock,
complete with altered size with out preparing reveals. (Size 750mmx1025mm)
m2 5,127
L052 Door PVC supply and fixing to existing opening, with frame, Lock, complete
with altered size with out preparing reveals. (Size 750mmx1025mm)
m2 8,043
L053 Supplying and fixing PVC step nosing to stairway step edges using approved
adhesive.
m 533
Louver blades
L054 Louvre blades 10mm minimum thickness in (Group 1, Category A) timber up to
100mm width supplying and fixing. m 601
L055 Louvre blades 10mm minimum thickness in (Group 1, Category A) timber over
100mm and up to150mm. m 660
L056 Louvre blades 10mm minimum thickness in (Group 1, Category A) timber over
150mm and up to 225mm. m 893

Item Basic Rate

Code 2020
Wooden Posts
L057 Posts, verandah, 125mm x 125mm tapering to 100mm x 100mm in (Group3,
Category A) local timber, supplying and fixing on spur stones (spur stones paid
for separately) m 3,436
L058 Posts, verandah 150mm x 150mm tapering to 125mm x 125mm in (Group3,
Category A) local timber supplying and fixing on spur stones (spur stones paid
for separately) m 4,768
L059 Posts, Wooden, round jungle timber 125mm minimum and average 150mm dia.
supplying and fixing. m 309
Skirting
L060 Skirting in Teak ( 225mm x 25mm moulding and beading supplying and fixing
complete to wooden frame. m 2,282
L061 Supplying and fixing Skirting in Lunumedella board 150mm x 20mm on walls. m 1,052
Pantry cupboards units
L062 Supplying and fixing pantry cupboards top unit with (Group 2,Category A)
timber 25mm thick apx.2700mmx800mmx300mm (high) outer frame and
shashes.Applying two coats of woodsheen to exposed outer surface complete
with handles,conceal hinges,anchor bolts etc and painting 2 coats of varnish to
internal surface. m 39,808
L063 Supplying and fixing pantry cupboards bottom unit with (Group 2,Category A)
timber 25mm thick apx.2700mmx825mmx600mm (high) including Perstop
laminated worktop and drawers with runners, conceal hinges and handles fixed.
Applying two coats of woodsheen to exposed outer surface complete with
handles,conceal hinges,anchor bolts etc and painting 2 coats of varnish to internal
surface. ( Rate excluding sink, taps and other accessories)
m 49,612
Iron Mongary - L3
Cabin Hooks (Iron)
L064 Cabin Hooks and eyes, 50mm Iron, supplying and fixing. set 78
Cabin Hooks (Brass)
L069 Cabin Hooks 50mm polished, brass, heavy quality supplying and fixing with
brass screws. Nos 317
L070 Cabin Hooks 75mm polished, brass, heavy quality supplying and fixing with
L071 Cabin Hooks150mm polished, brass, heavy quality supplying and fixing with
L072 Cabin Hooks 200mm, polished, brass heavy Quality supplying & fixing with
L073 Cabin Hooks, 225mm, polished, brass heavy quality supplying & fixing with

Item Basic Rate

Code 2020
Casement fasteners, brass
L076 Casement Stays, Iron 250mm heavy quality, supplying and fixing. Nos 269
L077 Casement Stays, Iron 300mm heavy quality, supplying and fixing. Nos 290
Casement fasteners, brass
L078 Casement fasteners, brass with mortice plate, polished heavy quality supplying
and fixing with brass screws. Nos 522
L079 Casement stays, polished 250mm heavy quality supplying and fixing. Nos 466
L080 Casement stays, polished 300mm heavy quality supplying and fixing. Nos 508
L081 Fanlight Catches, brass heavy quality, supplying and fixing with brass screws
complete. Nos 601
L082 Handles, door, brass, polished heavy quality supplying and fixing with brass
screws complete. Nos 470
Hasp and staple, brass
L083 Hasp and staple 10mm iron, safety type of approved heavy quality, supplying and
fixing with iron screws. Nos 244
L084 Hasp and staple 150mm iron, safety type of approved heavy quality, supplying
and fixing with iron screws complete. Nos 255
L085 Hasp and staple 300mm x 50mm iron, specially made out of 6mm iron plate and
fixing with 6mm x 50mm bolts and nuts complete. Nos 3,019
Hasp and staple, brass
L086 Hasp and staple, Safety type, 150mm brass, polished heavy quality supplying and
fixing with brass screws, complete. Nos 527
L087 Hasp and staple, Safety type, 100mm brass, polished heavy quality supplying and
fixing with brass screws, complete. Nos 475
L088 Hat Hooks, brass, supplying and fixing with brass screws. Nos 277
Hinges (Iron)
L089 Hinges, butt, 50mm iron of approved heavy quality supplying and fixing with
iron screws. pairs 542
L090 Hinges, butt, 75mm iron of approved quality supplying and fixing with iron
screws. pairs 606
screws. pairs 692
screws. pairs 927
L093 Hinges supplied by Dept. fixing complete with screws. pairs 297
L094 Hinges, strap iron 37mm x 6mm, 300mm long supplying & fixing with necessary
bolts and nuts (excluding pintols) Nos 1,442
L095 Hinges, strap iron 50mm x 6mm, 900mm long supplying and fixing with
necessary bolts and nuts (excluding pintols) Nos 2,362
L096 Hinges, spring, Japanese Helical, door supplying and fixing with iron screws
complete. Nos 1,256

Item Basic Rate

Code 2020
Hinges, brass
L097 Hinges, butt, 50mm brass, polished heavy quality supplying and fixing with brass
screws complete. pairs 581
L098 Hinges, butt, 75mm brass polished heavy quality supplying and fixing with brass
screws complete. pairs 719
L099 Hinges, butt, 87.5mm brass polished heavy quality supplying and fixing with
brass screws complete. pairs 1,121
L100 Hinges, butt, 100mm brass polished heavy quality supplying and fixing with
L101 Hinges, butt, 125mm brass polished heavy quality supplying and fixing with
L102 Hinges center pivoted (consisting of 2 pieces) brass, polished heavy quality
supplying and fixing with brass screws complete. pairs 846
L103 Hinges, gravity, brass supplying and fixing with brass screws complete. pairs 963
L104 Hinges, Parliamentary, 100mm brass, polished heavy quality supplying and
fixing with brass screws complete. pairs 1,603
fixing with brass screws complete. Nos 836
fixing with brass screws complete. Nos 928
L107 Hinges, spring, double acting, brass 100mm supplying and fixing. Nos 1,919
Hinges (Stainless Steel) for Timber Doors
L108 Supplying and fixing UNION- Butt Hinges, 100mmx75mmx 3mm (thick)
stainless steel, for wooden doors with brass screws. pairs 3,665
Hinges (Stainless Steel) for Aluminium Doors
L109 Supplying and fixing UNION- Butt Hinges,100mmx75mmx 2mm (thick)
stainless steel, for Aluminium doors with pop rivets. pairs 2,398
Prime Cost of, UNION Butt Hinges, , 4"x3"x 2mm (thick) stainless steel, for
Aluminium doorsPrime Cost of, =2100 #####
Holdfast
L110 Holdfast 3.2mm x 50mm x 225mm flat iron supplying and fixing complete. per
no Nos 493
Prime Cost of, Flat iron 2"x⅛"Prime Cost of, =95 #####
L111 Locks, rim, 100mm iron, superior quality, heavy type supplying and fixing with
iron screws complete. Nos 1,525
L112 Locks, rim, 150mm iron, superior quality, heavy type supplying and fixing with
iron screws complete. Nos 1,283
L113 Locks, mortice, 100mm iron, superior quality, heavy type supplying and fixing
with iron screws complete. Nos 1,382
L114 Locks, mortice, 150mm iron, superior quality, heavy type supplying and fixing
with iron screws complete. Nos 1,677
L115 Locks, Bird type supplying and fixing with iron screws complete. Nos 949
Locks (Brass)
L116 Locks, cupboards, 62.5mm brass, 4 levers with brass screws supplying and fixing
complete. Nos 598

Item Basic Rate

Code 2020
L117 Locks, rim 150mm polished brass, 2 levers, superior quality and English make,
supplying and fixing. Nos 4,165
L118 Locks, rim 125mm single lever of best quality local manufacture, supplying and
fixing. Nos 2,905
L119 Supplying and fixing ,night latch/Rim Lock (Duplicate/Local), with duplicate
keys. Nos 1,776
L120 Supplying and fixing , Yale or Union, night latch Lock (Rim Lock), with
duplicate keys. (Nos: 1022C,1027 or 1028),(Imported, British or south African
make) Nos 8,518
L121 Door rings, brass 37.5mm to 44mm supplying and fixing to doors and windows
with brass screws. Nos 298
L122 Lock Mortice (local) single supplying & fixing. Nos 4,095
L123 Lock Mortice (local) double, supplying and fixing. Nos 6,221
L124 Supplying and fixing two Lever single door UNION Motice Lock
(No2295),(Imported, British or south African make). Nos 3,788
L125 Supplying and fixing two Lever double door UNION Motice Lock (No2242),
(Imported, British or south African make). Nos 7,437
L126 Supplying and fixing UNION Cylindrical Motice Lock (No:X985) including
Door handle pair,(Imported, British or south African make). Nos 12,455
L127 Supplying and fixing UNION Nob set Lock (No:X96300) (Imported, British or
south African make). Nos 6,132
L128 Supplying and fixing UNION Nob set Lock for Toilets (No:X96350) (Imported,
British or south African make). Nos 5,481
Door lock for Aluminium Doors
L129 Supplying and Fixing UNION Door lock (No-X 920,X925 or X930) for
Aluminium Door with necessary accessories to working order. Nos 5,587
Prime Cost of, UNION Door lock (No-X 920,X925 or X930) for Aluminium
DoorPrime Cost of, =4533 #####
L130 Supplying and Fixing Door lock(No-VR50101B) for Aluminium Door with
necessary accessories to working order. Nos 6,101
Prime Cost of, Door lock-VR50101BPrime Cost of, =5618 #####
L131 Supplying and Fixing Door lock(No-VR50101C) for Aluminium Door with
necessary accessories to working order. Nos 6,521
Prime Cost of, Door lock-VR50101cPrime Cost of, =6038
#####
Stainless Steel Door Handle for Aluminium Doors
L132 Supplying and Fixing lock for Aluminium Sliding door with necessary
accessories . Nos 1,087
Prime Cost of, Sliding door LockPrime Cost of, =772 #####
Stainless Steel Door Handle for Aluminium Doors
L133 Supplying and Fixing Stainless Steel Door Handle for Aluminium door with
necessary accessories . Nos 1,943
Prime Cost of, Stainless Steel Door handlePrime Cost of, =1628 #####

Item Basic Rate

Code 2020
Floor hinge
L134 Supplying and Fixing of UNION floor hinge (No: 8300) with necessary
accessories .(Imported, British or south African make)
Nos 29,668
Prime Cost of, UNION floor hing (No: 8300)Prime Cost of, =26250 #####
L135 Supplying and fixing imported floor hinges (new star) of approved quality
including chipping of existing floors and making good after completion. Nos 20,713
Prime Cost of, Floor hingePrime Cost of, =18323 #####
Door Closer
L136 Supplying and fixing door closer Japanese make of approved heavy quality
Nos 5,898
Prime Cost of, Door closer (new star)Prime Cost of, =5355 #####

Item Basic Rate

Code 2020
M-CLADDING
M001 Supplying, fabricating and installing of 4.0mm thick Aluminium composite
cladding panel (Alucobond or equivalent European make) with open joint tray
panel system using non corrosive 50x81x3mm tk. Aluminium "T" channel
section (al 217), non corrosive 50x50x3mm pressed aluminium "U" wall bracket
sub frame and AL 201 & AL 202 profiles on tray panel, Rate to include for ss nut
and bolts, ss screws, blind rivets, U channels, Nylon resistant, Anchor bolts, and
other necessary accessories. Bird mesh to be provided in side of vent areas, all
complete as per manufacture's specifications.
m2 12,950
M-1 This BSR is for construction works only

Item Basic Rate

Code 2020
N-PARTITIONS & SUSPENDED CEILING

Aluminium Partitions
Aluminium Partition Frame Work (max. height 3600mm) - with Fully
Fabric Board, 1.2mm thick, 76mm depth (max. width 23.0mm) extrusions
Supplying, Fabricating and Installing FULLY Fabric board ( both sides)

ALUMINIUM PARTITION consist of 1.2mm thick, 76mm depth (max. width
23.0mm) Aluminium extrusions and GI channel stiffener frame work enclosed in
Aluminium frame work with an appropriate grid pattern, span not exceeding
1200mm in both vertical & horizontal directions suited to the available space and
additional GI channel bracings placed in 600mm centers at vertical direction.
Rate inclusive of Aluminium beadings (including necessary rubber beadings)
necessary fasteners etc.
N001 -DO- Matt Finished Aluminium 2

m 6,974
N002 -DO- Natural Anodized Aluminium 2
m 7,066
N003 -DO- Bronzed Anodized Aluminium 2
m 7,092
N004 -DO-Powder Coated Aluminium 2
m 7,250
N005 -DO-Wood Finished Aluminium 2
m 7,785
Aluminium Partition Frame Work - top & bottom with Fabric Boards &
middle panel with Glass Pans (max. height 3600mm), 1.2mm thick, 76mm
depth (max. width 23.0mm) extrusions
Supplying, Fabricating and Installing Glass & Fabric Board ALUMINIUM
PARTITION frame work with 1.2mm thick, 76mm depth (max. width 23.0mm)
Aluminium extrusions. And top & Bottom panels consist of 3mm thick Fabric
Board (both sides) with GI channel stiffener frame work enclosed in appropriate
grid pattern, span not exceeding 1200mm in both vertical & horizontal directions,
suited to the available space and additional GI channel bracings placed in 600mm
centers at vertical direction. Middle panel consists of 5mm thick glass pans, span
not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings
(including necessary rubber beadings) necessary fasteners etc.
N006 -DO- Matt Finished Aluminium m2 6,799

m 6,924
m 6,958
m 7,146
m 7,909
N-1 This BSR is for construction works only

Item Basic Rate

Code 2020
Aluminium Partition Frame Work - top & bottom with PVC Boards &
middle panel with Glass Pans (max. height 3600mm), 1.2mm thick, 76mm
depth (max. width 23.0mm) extrusions
Supplying, Fabricating and Installing Glass & PVC Board ALUMINIUM
PARTITION frame work with 1.2mm thick, 76mm depth (max. width 23.0mm)
Aluminium extrusions. Top & Bottom panels consist of 3mm thick PVC Board
(both sides) with GI channel stiffener frame work enclosed in appropriate grid
pattern, span not exceeding 1200mm in both vertical & horizontal directions,
suited to the available space and additional GI channel bracings placed in 600mm
centers at vertical direction. Middle panel consists of 5mm thick glass pans, span
not exceeding 1200mm in both directions. Rate inclusive of Aluminium beadings
(including necessary rubber beadings) necessary fasteners etc.

m 5,841
m 5,874
m 6,063
m 6,825
Aluminium Partition Frame Work (max. height 3600mm) - with Fully PVC
Board, 1.2mm thick, 76mm depth (max. width 23.0mm) extrusions
Supplying, Fabricating and Installing 3mm thick Fully PVC board ( both sides)
ALUMINIUM PARTITION consist of 1.2mm thick, 76mm depth (max. width
23.0mm) Aluminium extrusions and GI channel stiffener frame work enclosed in
1200mm in both vertical & horizontal directions suited to the available space and
additional GI channel bracings placed in 600mm centers at vertical direction.

m 5,736
m 5,770
m 5,958
m 6,721

Item Basic Rate

Code 2020
Aluminium Partition Frame Work - 5 mm thick fully Glass (max. height

3600mm), 1.2mm thick, 76mm depth (max. width 23.0mm) extrusions
Supplying, Fabricating and Installing 5mm thick Fully Glass, ALUMINIUM

PARTITION consist of 1.2mm thick, 76mm depth (max. width 23.0mm)
Aluminium extrusions and GI channel stiffener frame work enclosed in
1200mm in both vertical & horizontal directions suited to the available space .
m 6,191
m 6,224
m 6,413
m 7,175
Aluminium Partition Frame Work - (max. height 3600mm) Fully Louvered.
1.2mm thick, 76mm depth (max. width 23.0mm) Aluminium extrusions
Supplying, Fabricating and Fixing FULLY ALUMINIUM LOUVERED

PARTITION with 1.2mm thick, 76mm depth (max. width 23.0mm) Aluminium
extrusions to form an appropriate grid pattern, span not exceeding 1200mm in
both vertical & horizontal directions, suited to the available space and all panels
consist of Louvers enclosed with Aluminium louver frame. Rate inclusive of
Aluminium beadings (including necessary rubber beadings) necessary fasteners
etc. (Rate for DG-01 & DG-101 louver extrusions)

m 15,550
m 16,032
m 17,425
m 24,526
Aluminium 76mm Shopfront
Supplying, Fabricating and Installing fully glass 1.2 mm thick,76mm Aluminium
Shopfront, frame work fixed as an appropriate grid pattern not exceeding
1200mm in both vertical & horizontal directions, suit to the available space
including 5mm thick glass pans necessary rubber beadings, fasteners etc.

m 7,252
m 7,311
m 7,640
m 9,004

Item Basic Rate

Code 2020
Aluminium Curtain Wall (1.5mm thick)

Supplying, Fabricating and Fixing Aluminium Curtain Wall with 1.5mm
thick,85mm depth extrusions, frame work fixed as an appropriate grid pattern,
span not exceeding 1200mm in both vertical & horizontal directions, suit to the
available space including 5mm thick glass pans, necessary rubber beadings,
fasteners etc.
m 10,580
m 10,767
m 11,345
m 13,414
Partitioning (Gypsum board)
N041 Supplying and fixing gypsum board partitioning with GI channel member frame
work fixed onto walls and floors , 12mm. thick gypsum board fixed to both sides
of frame work complete with making joints using joint tape and gypsum
compound to get wall finish . m2 8,188
Hot dip GI interlocking ceiling frame work only
N042 The frame members for suspended ceiling are in a standard kit (CKM or
equivalent). Main runners ( 38mmx24mmx3660mm) are fixed at 1220 centers
securely suspended using 4mm dia. GI hanging rod to the structural soffit or
timber roof, using an appropriate suspension at 1220mm centers, Cross Tees
(27mmx24mmx1220mm) of 1220mm length to be fixed between the main
runners at 610mm centers and another cross tees (27mmx24mmx610mm) fixed
at mid span between 610mm to form a grid structure of 610mmx 610mm in size.
wall angles (24mmx24mmx3050mm) are fixed at wall edges. ( Edge molding
and painting paid separately)
m2 2,790
(Mineral fiber / Stone wool) acoustic ceiling suspended ceiling
N043 Supplying & fixing of 600mm x600mm & 15mm thick (Mineral fiber / Stone
wool) Acoustic ceiling boards (Rockfon or equivalent-Provides sound insulation
from top and sound absorption within room level) lay on hot dip GI pre
engineered interlocking ceiling frame work. The frame members for suspended
ceiling are in a standard kit (CKM or equivalent). Main runners (
38mmx24mmx3660mm) are fixed at 1220 centers securely suspended using
4mm dia adjustable GI hanging rod with spring clips to the structural soffit or
existing roof structure, using an appropriate suspension at 1220mm intervals
along each Main runners. Cross Tees (27mmx24mmx1220mm) of 1220mm
length to be fixed between the main runners at 610mm centers and another cross
tees (27mmx24mmx610mm) fixed at mid span between 610mm to form a grid
structure of 610mmx 610mm in size. wall angles (24mmx24mmx3050mm) are
fixed at wall edges.
m2 3,928

Item Basic Rate

Code 2020
N044 Supplying & fixing 1200mm x 600mm x 15mm thick Mineral fiber acoustic
ceiling boards lay on Existing interlock type ceiling frame work , forming a
panel side of 600mm X 600mm, and at the average elevation of 3600mm from
the working floor, (for 12 nos or 9m2) m2 1,340
N045 Supplying and installing mineral fiber Japanese make suspended exposed ceiling
system, using 1200mm x 600mm X 15 mm thick ceiling boards, lay on white
colour interlock type, hot dip GI grid system , forming a panel side of 1200mm x
600mm, and suspended on 4mm rods with spring clip to soffit of concrete or
timber roofs. ( Edge molding paid separately) m2 4,081
N046 Supplying and installing mineral fiber Japanese make suspended exposed ceiling
(Reaveal edge) system, using 605 mm X 605 mm X 15 mm white colour ceiling
boards lay on white colour interlock type hot dip GI grid system , forming a panel
side of 610mmx610mm,and suspended on 4mm rods with spring clip to soffit of
concrete or timber roofs. . ( Edge molding & Painting paid separately)
m2 4,264
Super Flex Suspended ceiling
N047 Supplying and installing Super Flex (Plain) suspended ceiling system, using
1200mm X 1200mm X 3.2 mm ceiling boards lay on white colour interlock type
hot dip GI grid system , forming a panel side of 600mm X 600mm , and
suspended on 4mm rods with spring clip to soffit of concrete or timber roofs. (
Edge molding & Painting paid separately) m2 2,019
N048 Supplying and installing Super Flex (with design) suspended ceiling system,
using 1200mm X 1200mm X 3.2 mm ceiling boards in white colour interlock
type hot dip GI grid system , forming a panel side of 600mm X 600mm, and
suspended suspended on 4mm rods with spring clip to soffit of concrete or
timber roofs ( Edge molding & Painting paid separately)
m2 2,093
Gypsum board suspended ceiling
N049 Supplying and fixing gypsum board suspended ceiling . using 600mm x 600mm
X 9 mm. thick ceiling boards in white colour interlock type hot dip GI grid
system , forming a panel side of 600mmx600mm, and suspended suspended on
4mm GI hanging rods with spring clip to soffit of concrete or timber roofs (
Edge molding & Painting paid separately) m2 3,742
Metal ceiling
N050 Supply and installation of concealed type metal false ceiling, Including revel edge
of 600mm x 600mm size 0.5mm minimum thickness, epoxy powder painted steel
Tiles (paint film thickness of average 80microns ) suspended to the roof frame
work with, 0.3 mm thick pre painted hot dip galvanized, 15mm x 38mm plain
TEE-grid bars and 20mm x 24mm wall angles, suspended with adjustable
burrerfly clip, 4mm dia. surface treated galvanized steel hanger rods, complete
with necessary anchor bolts and any other accessories. (All in accordance with
the approved shop drawings, to the Engineers' satisfaction. )
m2 5,813

Item Basic Rate

Code 2020
N051 Supply and installation of lay in type "E-Metallic Aluminum ceiling, Including
revel edge of 600mmx600mm size 0.7mm average thickness, 80 microns high
quality powder coated Aluminum perforated or plain ceiling panels,. Suspended
to the roof frame work with hot dip galvanized "T" bars of 14mm x 38mm and
wall angles of 19mm x 24mm suspended with, adjustable burrerfly clip, 04mm
GI hanging roads, anchor bolts and all other accessories. (All in accordance with
the approved shop drawings, to the Engineers' satisfaction. )
m2 6,807
Ceiling panels (Pinholes)
N052 Supplying, fixing aluminium 600mmx600mm ceiling panels (Pinholes) with
aluminium frame work and adjustable. m2 4,986

Item Basic Rate

Code 2020
P-ROOF COVERING AND ROOF PLUMBING

Tiles, Calicut pattern, flat
P001 Tiles Calicut pattern, supplying and laying in any building on existing roof frame.
m2 1,144
Tiles half round
P002 Tiles half round, supplied and laid in any building on existing roof frame. m2 6,943
P003 Supplying and laying half round tiles on the existing asbestos roof. 2
m 3,681
Zinc Aluminium Colour bonded Steel Roofing
P004 Supplying and fixing Zinc Aluminium colour bonded steel roofing sheets ( 0.47
gauge )on existing frame work using nut & bolt / self tapping screws or fasteners.
m2 2,198
P005 12mm thick heat and sound installation sheet (double side luminary aluminium
foil) laying on 75mm x 75mm GI mesh under roof covering. m2 1,049
Corrugated Asbestos sheets
P006 Corrugated asbestos sheet roofing on category A timber purlins supplied and
fixed complete including treating timber with wood preservative (Ridging
measured separately). m2 3,252
P007 Corrugated asbestos sheets supplied and fixed to roof or wall on existing
framework with necessary coach screws and limpet washers or hook bolts. m2 1,251
Ridging
P008 Ridging, Calicut pattern, bedded in cement and lime mortar 1:1:4, coloured to
match tiles. m 692
P009 Ridging, half round tiles, bedded in lime, cement mortar 1:1:4 and coloured to
match tiles. m 1,001
P010 Ridging, Galvanized iron 24 B.W.G 18" wide overall supplied and fixed
complete. m 736
P011 Supplying and fixing Zinc Aluminium colour bonded standard steel ridge cap to
existing sheet roof using new fasteners or st /screws. m 1,377
P012 0.47mm thick ,width 450mm Zink aluminium sheet ridging and fixing to roofing
sheet with self trapping screws m 818
P013 Ridging with asbestos cement close fitting ridges supplied and fixed complete
with roofing screws or hook bolts. m 1,205
G.I Flashing
P014 Flashing, G.I 22 B.W.G 450mm wide, supplying and fixing with 150mm turning
up along, and top edge tucking well into wall in cement and lime mortar.
m 1,630
P015 18 BWG (1.2mm) galvanized iron flashing 450mm girth overall 3 times bent
with end laps not less than 150mm lead soldered turned and tucked up to not less
than 6" into chase out in wall and pointed in cement mortar 1:2 lower end dressed
over roof covering. m 1,819
Valley gutter
P016 Gutters valley, 18 B.W.G 900mm wide, renewing including timber 25mm thick
boarding, sheet t be tarred, joints to be soldered and cement lime filleting
complete. m 8,060
P-1 This BSR is for construction works only

Item Basic Rate

Code 2020
P017 Supplying and fixing Zinc Aluminium sheet valley gutter (0.47mm) thick ,width
457mm and fixing to roof with self trapping screws.(Excluding timber boarding)
Hi-tensile (Grade-550) Colour m 1,669
P018 Supplying and fixing Zinc Aluminium sheet valley gutter (0.47mm) thick ,width
914mm and fixing to roof with self trapping screws.(Excluding timber boarding).
Hi-tensile (Grade-550) Colour m 2,337
G.I semicircular Gutters
P019 Gutters, eaves 150mm G.I semicircular 22 B.W.G making and fixing with hooks
or brackets and screws, and joints to be soldered complete. m 1,619
P020 Gutter, eaves 150mm moulded, G.I 22 B.W.G making and fixing complete
including brackets. m 2,087
P021 Gutters, existing, making opening to receive 100mm to 150mm down pipe,
attaching spigot piece, joints to be soldered and making good. Nos 1,413
P022 Gutter heads, 250mm x 250mm x 600mm making of G.I Sheets 22 B.W.G and
fixing. Nos 5,257
P023 Making and fixing Gutter heads, 225mm x 225mm x 300mm of G.I Sheets 22
B.W.G . Nos 4,134
P024 Gutter hooks or brackets 20mm x 3mm supplying and fixing complete with Iron
screws. Nos 377
Aluminium, Zn/Alu high tensile down pipes
P025 Supplying, fixing 0.47mm tk., Zn/Alu high tensile down pipe (914mm girth)
with brackets. m 1,949
P026 Supplying, fixing 0.47mm tk., Zn/Alu high tensile down pipe (457mm girth)
with brackets. m 1,147
Zn/Alu gutters
P027 Supplying, fixing 0.47mm tk., Alu gutters (914mm girth) with brackets &
specials. m 2,171
P028 Supplying, fixing 0.47mm tk., Alu gutters (457mm girth) with brackets &
specials. m 1,243
Zn/Alu Down pipe Bends
P029 Supplying, fixing 0.47mm tk., Zn/Alu high tensile. Down pipe Bend (for 914mm
girth gutter) with brackets & specials. Nos 1,476
P030 Supplying, fixing 0.47mm tk., Zn/Alu high tensile. Down pipe Bend (for 457mm
girth gutter) with brackets & specials. Nos 930
Elbows for down pipe.
P031 Supplying & fixing 90mm P.V.C. elbows for down pipe.
Nos 455
Running head.
P032 Supplying & fixing , only a P.V.C. running head.
Nos 621
Gutter end.
P033 Supplying & fixing , only a square type P.V.C. gutter ends.
Nos 437
Gutter Joint.
P034 Supplying & fixing , only a square type P.V.C. gutter joints.
Nos 442
Eves gutters (PVC)

Item Basic Rate

Code 2020
P035 Supplying and fixing eves gutters square type PVC with necessary specials,
including running heads, mitre joints, gutter joints, gutter brackets, gutter ends
etc. m 767
P036 150mm diameter half round PVC eaves gutter fixed to timber valance board
including gutter joiner and brackets fixed at 450mm centers.(other specials paid
separately) m 564
Down pipes 100mm (3 ½") dia. P.V.C
P037 Supplying & fixing rain water down pipes 100mm (3½") dia. P.V.C to wall, with
necessary specials, including elbows, sockets, clips etc. m 631
Skylight glass
P038 Skylight glass 600mm x 600mm, 6mm thick ribbed, supplied & fixed to roof
including necessary lime cement filleting. Nos 2,249

Item Basic Rate

Code 2020
Q-PLUMBER
Ball valve-UPVC
Q001 Supplying & fixing UPVC ball valve 20mm dia. (S-Lon or equivalent) Nos 433
Q002 Supplying & fixing UPVC ball valve 25mm dia. (S-Lon or equivalent)
Nos 533
Ball valve-Brass
Q005 Supplying & fixing Brass Ball valve ½" or 20mm-(Peglar or equivalent.) Nos 1,604
Q006 Supplying & fixing Ball valve Brass ¾" or 25mm-(Peglar or equivalent.) Nos 1,974
Q007 Supplying & fixing Ball valve Brass 1" or 32mm-(Peglar or equivalent.) Nos 2,827
Supplying & fixing Ball valve Brass 1½" or 50mm -(Peglar or equivalent.) with
Q008
necessary fittings. Nos 6,028
Concealed Taps/Valves-Chromium plated
Q009 Supply and fixing concealed valve20mm dia. Prime cost : Rs. 2300.00
Nos 2,595
Flush valve
Q010 Supplying and fixing wall Urinal Flush Valve(FM 3A903)-High Quality Nos 7,645
Prime cost : Rs. 7350.00 80068 0
Gate valve brass for Max. 17.5 bars (Pegler 1065 or equivalent)
Q011 Supplying and fixing 15mm dia: gate valve brass imported (Pegler or equivalent,
approved quality). Nos 1,565
Float valve (Pegler 855 or equivalent)
Q018 Supplying & fixing 20mm dia. brass float valve with necessary fittings Nos 3,991
Q-1 This BSR is for construction works only

Item Basic Rate

Code 2020
Foot valve - Copper
Q022 Supplying & fixing 32mm dia. Copper foot valve with necessary fittings Nos 6,920
Foot valve PVC
Q025 Supplying & fixing 32mm dia. PVC foot valve with necessary fittings (L/D or
equivalent) Nos 1,245
Close coupled water closet suite (white) -Imported
Q031 Supplying & fixing, close coupled water closet suite, white, (4/2.6 Lit ) with
water closet Pan, Cistern, Seat & Seat cover and trap etc.: complete. (BECA-
American standards) Nos 60,500
Prime Cost : Rs. 56,400.00 80661
Close coupled water closet suite (white)-Manufactured in Sri Lanka.
Q032 Supplying & fixing, Vitreous china floor standing close coupled, Water Closet
(toilet) suite (white / Colour) with wash down 6/3 liter dual flushing. Has a
horizontal outlet and cistern with water inlet from bottom. Complete with Seat,
Seat cover and concealed trap etc. . (Make: Rocell , Model: URBAN-D ) Nos 26,800
Prime Cost : Rs. 22,700.00 80662
(toilet) suite(White/ Colour) with wash down 6/3 liter dual flushing. Has a
horizontal outlet and cistern with water inlet from bottom. Complete with Seat,
Seat cover and concealed trap etc. . (Make: Rocell , Model: DUNE ) Nos 30,590
Prime Cost : Rs. 26490.00 80663
(toilet) suite with wash down 6/3 liter dual flushing. Has horizontal outlet and
two lateral holes for bottom water connection. Cistern with water inlet from
bottom. Complete with Seat, Seat cover and concealed trap etc. . (Make: Rocell ,
Model: INTENCE ) Nos 44,880
Prime Cost : Rs. 40780.00 80664

Item Basic Rate

Code 2020
Model: Elements Aqua ) Nos 40,150
Prime Cost : Rs. 36,050.00 80666
Model: Aqua+ ) Nos 46,930
Prime Cost : Rs. 42,830.00 80667
Model: Summer Blue ) Nos 92,360
Prime Cost : Rs. 88,260.00 80668
two lateral holes for bottom water connection. In-Wall Tank Cistern with water
inlet from bottom. Complete with Seat, Seat cover and concealed trap etc. .
(Make: Rocell , Model: Eternity ) Nos 79,760
Prime Cost : Rs. 72960.00 80669
(Make: Rocell , Model: Urbanity ) Nos 80,630
Prime Cost : Rs. 73,830.00 80670
(Make: Rocell , Model: Escape ) Nos 80,330
Prime Cost : Rs. 73,530.00 80671
Q041 Supplying & fixing Vitreous china floor standing bidet (white colour), Nominal
size ( 560mm x 370mm) floor to Rim height 407mm, complete with overflow
not included Nos 14,609

Prime Cost : Rs. 12970.00 80726
Q042 Supplying & fixing Vitreous china floor standing bidet (white colour), Nominal
size (560mm x 394mm) floor to Rim height 420mm, complete with overflow
Faucets not included Nos 14,609

Prime Cost : Rs. 12970.00 80727
Item Basic Rate

Code 2020
Closet-squatting type
Q043 Supplying & fixing closet, squatting type, with trap. Prime Cost : Rs. 4790.00 Nos 9,197
Squatting pan- European

Q044 Supplying and fixing foot rest type squatting pan and trap colour to working
order.(American standards) Nos 25,531
Prime Cost : Rs. 21183.00 80651
Closet squatting type ( Indian or equivalent)
Q045 Supplying & fixing closet squatting type with trap complete with cistern plastic
flush pipe etc. Nos 32,449
Prime Cost : Rs. 24,800.00 80657
Urinal Imported- Twyford
Q046 Supplying and fixing (New wash brook ) urinal.(American standards) Nos 40,541
Prime Cost : Rs. 38,400.00 80702
Q047 Supplying & fixing Wall urinal with brackets.(American standards) Nos 15,429
Prime Cost : Rs. 14,900.00 80703
Urinal - Manufactured in Sri Lanka.
Q048 Supplying & fixing Wall urinal with Flush Valve.(Flo Point Urinal - Rocell) Nos 32,299
Prime Cost : Rs. 31,770.00 80704
Q049 Supplying & fixing Wall urinal with Flush Valve.(Dew Point Urinal - Rocell)
Nos 26,719
Prime Cost : Rs. 26,190 80705
Q050
Supplying & fixing Wall urinal with Sensor.(Flo Point Urinal - Rocell) Nos 47,209
Prime Cost : Rs. 46,680.00 80706

Q051
Supplying & fixing Wall urinal with Sensor.(Dew Point Urinal - Rocell) Nos 37,229
Prime Cost : Rs. 36,700.00 80707

Sink
Q052 Supplying & fixing sink, glazed, earthenware 762mm x 508mm x 203mm with
waste plug, brackets etc. complete. Prime Cost : Rs. 7875.00 Nos 10,554
Q053 Supplying & fixing sink, glazed earthenware 610mm x 458mm x 203mm with
waste plug, brackets etc., complete. Prime Cost : Rs. 5775.00 Nos 8,454
Stainless steel kitchen sink
Q054 Supplying & fixing approved quality, stainless steel kitchen sink with single bowl
& draining board with necessary waste plug, brackets etc.: Nos 7,628
Prime Cost : Rs. 6720.00 80763
Q055 Supplying & fixing approved quality, stainless steel kitchen sink with double
bowl & draining board with necessary waste plug, brackets etc.: Nos 14,258
Prime Cost : Rs. 13125.00 80764

Item Basic Rate

Code 2020
Q056 Supplying & fixing 800mm X510mm stainless steel kitchen sink with single
bowl & draining board with necessary waste plug, brackets etc.: (Teka or
Equivalent) Nos 22,113
Prime Cost : Rs. 21,205.00 80765
Q057 Supplying & fixing 1600mm X 510mm stainless steel kitchen sink with double
bowl & draining board with necessary waste plug, brackets etc.: (Teka or
Equivalent) Nos 42,346
Prime Cost : Rs. 41,213.00 80766
Wash Basin
Q058 supplying and fixing Lavatory wash basin with pedestal (American Standard or
Prime Cost : Rs. 25,200.00 80620
Wash Basin (local Bath wear)
Q059 Supplying & fixing Vitreous China floor standing wash basin (white colour)
having nominal side of ( 584mm x 457mm ) with universal height pedestal of
floor to Rim height 838mm, over flow hole and single tap hole in center,
including pedestal, Wash basin fixing kit. (Urband D-Rocell)
Faucets, waste pipe, paid separately Nos 15,055
Prime Cost : Rs. 12,590.00 80627
having nominal side of (622mm x 483mm) with universal height pedestal of floor
to Rim height 825mm, over flow hole and single tap hole in center, including
pedestal, Wash basin fixing kit. (Dune-Rocell)
Nos 15,355
Prime Cost : Rs. 12,890.00 80628
pedestal, Wash basin fixing kit. (Intense-Rocell)
separately Nos 28,525
Prime Cost : Rs. 26,060.00 80629
pedestal, Wash basin fixing kit. (Elements Aqua-Rocell)
Prime Cost : Rs. 20670.00 80630
pedestal, Wash basin fixing kit. (Aqua+ -Rocell)
Prime Cost : Rs. 21,460.00 80631

Item Basic Rate

Code 2020
Q064 Supplying & fixing Vitreous China floor standing wash basin (white colour) wall
mounted brackets, over flow hole and single tap hole in center, Wash basin fixing
kit. (Summer Blue-Rocell) Nos 43,475
Prime Cost : Rs. 41,010.00 80632
kit. (Eternity-Rocell) Nos 22,525
Prime Cost : Rs. 20,060.00 80633
kit. (Urbanity-Rocell) Nos 30,005
Prime Cost : Rs. 27,540.00 80634
Corner wash basin (local Bath wear)
Q067 Supplying & fixing corner wash basin with one tap, waste plug, new brackets
etc.(Aqua Corner - Rocell) Nos 11,054
Prime Cost : Rs. 8,290.00 80635
Vanity basin
Q068 Supplying and fixing Vanity basin 35mm x 406mm white.(Refresh-Twyford or
equivalent approved quality) Nos 25,137
Prime Cost : Rs. 22827.00 80625
Rubber plugs
Q069 Supplying & fixing plugs, rubber 32mm to 40mm for wash basins and sinks. Nos 119
Q070 Supplying & fixing plugs, rubber 50mm to 63mm for wash basins and sinks. Nos 124
Wooden plugs
Q071 Bedding in cement mortar 1:2, plugs, wooden, in (Group 6 category A) timber
100mm long, tapered 75mm to 50mm square section, including making holes in
walls, floor etc. Nos 201
Bottle traps
Q072 Supplying & fixing 40mm dia: plastic bottle trap Nos 609
Prime Cost : Rs. 478.00 80479
Q073 Supplying & fixing 50mm dia: plastic bottle trap
Nos 714
Prime Cost : Rs. 583.00 80480
Q074 Supplying & fixing 63mm dia: plastic bottle trap Nos 898
Prime Cost : Rs. 767.00 80481
Q075 Supplying & fixing 40mm dia: bottle trap stainless steel approved quality. Nos 5,331
Prime Cost : Rs. 5,200.00 80482
Q076 Supplying & fixing 40mm square bottle trap stainless steel approved quality. Nos 5,031
Prime Cost : Rs. 4,900.00 80483
Bib Taps (Metallic)
Q077 Supplying & fixing brass (Chromium plated), bib taps, 20mm (Rocell or
equivalent, approved quality) Nos 3,294
Prime Cost : Rs. 3,100.00 80820
Item Basic Rate

Code 2020
Bib Taps (Plastic)

Q078 Supplying & fixing Plastic Bib Tap 20mm dia. (T- Handle) (S-Lon or
Equivalent.) Nos 475
Prime Cost : Rs. 300.00 80320
Q079 Supplying & fixing Plastic Bib Tap 20mm dia. (Round- Handle)(S-Lon or
Prime Cost : Rs. 300.00 80321
Q080 Supplying & fixing Plastic Bib Tap 25mm dia. (T- Handle) (S-Lon or
Prime Cost : Rs. 380.00 80322
Q081 Supplying & fixing Plastic Bib Tap 25mm dia. (Round- Handle)(S-Lon or
Prime Cost : Rs. 440.00 80323
Q082 Supplying & fixing Plastic long, Neck Bib Tap 20mm dia. (T- Handle) (S-Lon or
Prime Cost : Rs. 245.00 80324
Q083 Supplying & fixing Plastic Bib Tap, long Neck 20mm dia. (Round- Handle)(S-
Lon or Equivalent.) Nos 495
Prime Cost : Rs. 320.00 80325
Swan-Neck tap-(Metallic)
Q084 Supplying & fixing chromium plated swan-neck tap 20mm with necessary
specials. Nos 4,481
Prime Cost : Rs. 4100.00 80829
Swan-Neck tap-(Plastic)
Q085 Supplying & fixing Plastic Swan- tap 20mm dia. (T- Handle) (S-Lon or
Equivalent.) Nos 1,646
Prime Cost : Rs. 1265.00 80338
Q086 Supplying & fixing Plastic Swan-Neck tap 20mm dia. (Round- Handle)(S-Lon
or Equivalent.) Nos 1,646
Prime Cost : Rs. 1265.00 80339
Chromium plated angle Valves 20mm
Q087 Supplying & fixing chromium plated angle tap 20mm with necessary specials,
imported, approved quality. (Rocell or equivalent). Nos 1,781
Prime Cost : Rs. 1400.00 80832
Q088 Supplying & fixing chromium plated angle tap 20mm with necessary specials,
imported, approved quality. (Plumber or equivalent). Nos 2,064
Prime Cost : Rs. 1683.00 80833
Angle Valves (Plastic)
Q089 Supplying & fixing Plastic Angle Tap 20mm dia. (T- Handle) (S-Lon or
Prime Cost : Rs. 290.00 80334

Item Basic Rate

Code 2020
Q090 Supplying & fixing Plastic Angle 20mm dia. (Round- Handle)(S-Lon or
Prime Cost : Rs. 320.0 80335
Chromium plated basin tap 20mm
Q091 Supplying and fixing basin tap. Nos 5,360
Prime Cost : Rs. 5100.00 80618
Self Closing taps
Q092 Supplying & fixingself closing tap - 20mm chromium plated. Nos 10,994
Prime Cost : Rs. 10,800.00
Sensor taps
Q093 Supplying & fixing sensor taps, 20mm . Nos 18,774
Prime cost: Rs. 15000.00
Stop Taps (Plastic)
Q094 Supplying & fixing Plastic Stop Taps 20mm dia. (T- Handle) (S-Lon or
Prime cost: Rs. 285.00 80328
Q095 Supplying & fixing Plastic Stop Taps 20mm dia. (Round- Handle)(S-Lon or
Prime cost: Rs. 300.00 80329
Prime cost: Rs. 425.00 80330
Prime cost: Rs. 570.00 80329
Prime cost: Rs. 590.00 80332
Prime cost: Rs. 750.00 80333
Garden Taps (brass)
Q100 Supplying & fixing garden tap 20mm dia: brass, heavy quality, with necessary
specials, imported, approved quality. Prime cost: Rs. 2054.00
Nos 2,229
Garden Taps (Plastic)
Q101 Supplying & fixing Plastic Garden Tap 20mm dia. (T- Handle) (S-Lon or
Prime cost: Rs. 350.00 80326
Q102 Supplying & fixing Plastic Garden Tap 20mm dia. (Round- Handle)(S-Lon or
Prime cost: Rs. 440.00 80327

Item Basic Rate

Code 2020
Pillar cocks
Q103 Supplying & fixing pillar cocks 20mm Chromium plated, to basins. (Plumber or
equivalent) :Prime cost Rs. 2,500.00 Nos 2,881
Pillar taps
Q104 Supplying and fixing 20mm dia: chromium plated Pillar tap. (T- handle) Nos 4,875
Prime cost: Rs. 4700.00 80900
Q105 Supplying and fixing 20mm dia: chromium plated Pillar tap. (Round- handle)
Nos 3,031
Prime cost: Rs. 2650.00 80899
Basin Piller Taps (Plastic)
Q106 Supplying & fixing Plastic Basin Piller tap 20mm dia. (Round- Handle)(S-Lon
or Equivalent.) Nos 1,141
Prime cost: Rs. 760.00 80336
Stop cock
Q107 Supplying & fixing stop cock, brass 20mm dia. Nos 1,669
Q112 Supplying & fixing stop cock, brass 63mmdia. Nos 16,264
Q113 Supplying & fixing stop cock, chromium plated 20mm dia . Nos 1,669
Hooks for pipes
Q114 Hooks for 20mm pipes, supplying and fixing. Nos 41
Q119 Hooks for pipes, available, fixing. Nos 26
Jam Nuts
Q120 Jam Nuts, G.I 1/2"(12.5mm) supplying and fixing. Nos 102
Q121 Jam Nuts, G.I 3/4"(20mm) supplying and fixing. Nos 113
Q122 Jam Nuts, G.I 1"(25mm) supplying and fixing. Nos 138
Q123 Jam Nuts, G.I 1 1/4"(31.25mm) supplying and fixing. Nos 148
Q124 Jam Nuts, G.I 1 1/2"(37.5mm) supplying and fixing. Nos 166
Q125 Jam Nuts, G.I 2"(50mm) supplying and fixing. Nos 253
Nipples, G.I
Q126 Nipples, G.I 1/2"(12.5mm) Supplying & fixing. Nos 138
Q127 Nipples, G.I 3/4"(20mm) Supplying & fixing Nos 158
Q128 Nipples, G.I 1"(25mm) Supplying & fixing. Nos 198
Q129 Nipples, G.I 1 1/4"(31.25mm) Supplying & fixing. Nos 248
Q130 Nipples, G.I 1 1/2"(37.5mm) Supplying & fixing. Nos 318
Q131 Nipples, G.I 2"(50mm) Supplying & fixing. Nos 378

Item Basic Rate

Code 2020
Pipes G.I
Q132 Pipes G.I 1/2"(12.5mm) heavy quality supplying and fixing (fittings to be paid for
separately) including any necessary trenching, backfilling and making good, or
fixing to walls (pipe hooks to be paid for separately) m 872
Q133 Pipes G.I 3/4"(20mm) heavy quality supplying and fixing (fittings to be paid for
fixing to walls (pipe hooks to be paid for separately). m 977
Q134 Pipes, G.I 1"(25mm) heavy quality supplying and fixing (fittings to be paid for
fixing to walls. (Pipe hooks to be paid for separately) m 1,122
Q135 Pipes, G.I 1 1/4"(31.25mm) heavy quality supplying and fixing (fittings to be
paid for separately) including any necessary trenching, backfilling and making
good, or fixing to walls. (Pipe hooks to be paid for separately) m 1,440
Q136 Pipes, G.I 1 1/2"(37.5mm) heavy quality supplying and fixing (fittings to be paid
for separately) including any necessary trenching, backfilling and making good,
or fixing to walls. (Pipe hooks to be paid for separately) m 1,843
Q137 Pipes, G.I 2"(50mm) heavy quality supplying and fixing (fittings paid for
Q138 Pipes, G.I 2 1/2" (60mm) heavy quality supplying and fixing (fittings paid for
Q139 Pipes, G.I 3"(75mm) heavy quality supplying and fixing (fittings to be paid for
GI Plugs
Q140 Plugs, G.I 1/2"(12.5mm) supplying and fixing. Nos 89
Q141 Plugs, G.I 3/4" (20mm)supplying and fixing. Nos 107
Q142 Plugs, G.I 1"(25mm) supplying and fixing. Nos 130
Q143 Plugs, G.I 1/4"(31.25mm) supplying and fixing.
Nos 140
Q144 Plugs, G.I 1 1/2"(37.5mm) supplying and fixing. Nos 162
Q145 Plugs, G.I 2"(50mm) supplying and fixing. Nos 214
Socket G.I
Q146 Socket G.I 1/2"(12.5mm) plain supplying & fixing. Nos 133
Q147 Socket, G.I 3/4"(20mm) plain supplying and fixing. Nos 145
Q148 Socket, G.I 1" (25mm) plain supplying and fixing. Nos 168
Q149 Socket, G.I 1 1/4" (31.25mm) plain supplying and fixing. Nos 191
Q150 Socket, G.I 1 1/2"(37.5mm) plain supplying and fixing. Nos 214
Q151 Socket, G.I 2"(50mm) plain supplying and fixing. Nos 332
Q152 Socket, G.I 3"(75mm) plain supplying and fixing. Nos 554
Q153 Socket, G.I reducing 3/4"(20mm) to smaller sizes supplying and fixing. Nos 177
Q154 Socket, G.I reducing 1" (25mm)to smaller size supplying and fixing. Nos 181
Q155 Socket, G.I reducing 1 1/4"(31.25mm) to smaller sizes supplying and fixing. Nos 250
Q156 Socket, G.I reducing 1 1/2"(37.5mm) to smaller sizes supplying and fixing. Nos 304

Item Basic Rate

Code 2020
Q157 Socket G.I reducing 2"(50mm) to smaller sizes, supplying and fixing. Nos 382
Q158 Sockets G.I reducing 3"(75mm) to smaller sizes supplying and fixing. Nos 436
Plastishell (Single Layer) water tank (Slon PE+ or Equivalent)
Q159 Supplying and fixing Plastishell (Single Layer) water tank 350 liter capacity. (
fittings paid for separately ). Nos 10,219
Prime cost: Rs. 7600.00 80556
Prime cost: Rs. 9670.00 80573
Prime cost: Rs. 16000.00 80557
Prime cost: Rs. 21535.00 80558
Plastishell (Triple Layer) water tank (Slon PE+ Premium or Equivalent)
Q163 Supplying and fixing Plastishell (Triple Layer) water tank,5000 liter capacity. (
Prime cost: Rs. 86700.00 80576
Floater switch
Q164 Supplying and fixing floater switch with necessary fittings to over head water
tank. Nos 2,800
Prime cost: Rs. 1000.00
Tees
Q165 Tees, G.I 1/2"(12.5mm) equal supplying and fixing. Nos 226
Q166 Tees, G.I 3/4" (20mm) equal supplying and fixing. Nos 243
Q167 Tees, G.I 1"(25mm) equal supplying and fixing. Nos 317
Q168 Tees, G.I 1 1/4"(31.25mm) equal supplying and fixing. Nos 409
Q169 Tees, G.I 1 1/2"(37.5mm) equal supplying and fixing. Nos 493
Q170 Tees, G.I 2"(50mm) equal, supplying and fixing. Nos 698
Soap tray/dish
Q171 Supplying and fixing chromium plated soap tray. (American Standard or
Prime Cost Rs. 9020.00 80786
Q172 Supplying and fixing soap dish (American Standard or Equivalent.) Nos 5,150
Prime Cost Rs. 4780.00 80788
Q173 Soap dispenser
Supplying & fixing soap dispenser (American Standard or Equivalent.) Nos 43,989
Prime Cost Rs. 43,760.00 80787
Towel rail
Q174 Supplying & fixing chromium plated Towel rail (American Standard or
Equivalent.-S. No:6588) , 600mm long and , 25mm dia. with necessary rawl
plugs and screws. Nos 6,772
Prime Cost Rs. 6,370.00 80799
Item Basic Rate

Code 2020
Paper holder SEVA

Q175 Supplying & fixing SEVA paper holder (American Standard or Equivalent.)
complete to working order. Nos 5,988
Prime Cost Rs. 5,840.00 80793
Tooth brush holder
Q176 Supplying & fixing tooth brush holder (American Standard or Equivalent.)
Prime Cost Rs. 3,940.00 80808
Robe hook (SEVA)
Q177 Supplying & fixing SEVA Robe hook (American Standard or Equivalent.)
Prime Cost Rs. 4,510.00 80602
Bath room mirror,
Q178 Supplying & fixing mirror, beveled, bath room type, oval shape, 508mm x
406mm Max. and min. dimensions, to wall with Rawl plugs and chromium
plated fittings. Nos 5,956
Prime Cost Rs. 5000.00 80645
Q179 Supplying & fixing 610mm x 203mm, 5mm thickness beveled rectangular
mirror, to wall with Rawl plugs, noton tape and chromium plated fittings.
Nos 4,606
Prime Cost Rs. 3,650.00 80646
Shower rose
Q180 Supplying & fixing shower Rose 175mm chromium plated. Nos 450
Q181 Supplying & fixing PVC- 150mm x 20mm shower rose. Nos 911
Plastic Jet Shower rose
Q182 Supplying & fixing Plastic Jet Shower Rose 20mm dia. (S-Lon or Equivalent.) Nos 1,032
Q183 Supplying & fixing Jet shower complete(American Standard or Equivalent.)
Nos 7,975
Prime Cost Rs. 7784.00 80336
Shower head
Q184 Supplying & fixing Shower head with arm. (American Standard) Nos 7,091
Prime Cost Rs. 6,900.00 80777
Bidet spray imported
Q185 Supplying and fixing bidet spray - Plastic Nos 1,702
Prime Cost Rs. 1,300.00 80735
Q186 Supplying and fixing bidet spray Chromium Plated (Plumber or equivalent) Nos 4,212
Prime Cost Rs. 3800.00 80736
Bends P.V.C
Q187 Supplying & fixing bends P.V.C 20mm. Nos 102

Item Basic Rate

Code 2020

Q193 Supplying & fixing bends P.V.C 90mm. Nos 1,905
Elbows P.V.C
Q194 Supplying & fixing elbows P.V.C 20mm. Nos 87
Reducing sockets & Tees P.V.C
Q201 Supplying & fixing sockets reducing P.V.C (25mm x 20mm ) to smaller sizes. Nos 99
Q202 Supplying & fixing sockets reducing P.V.C (32mm x 25mm) to smaller sizes. Nos 115
Q204 Supplying & fixing sockets reducing P.V.C (50mm x40mm) to smaller sizes. Nos 197
Q206 Supplying & fixing sockets reducing P.V.C (63mm x50mm) to smaller sizes. Nos 245
Reducing Tees P.V.C
Q207 Supplying & fixing tees reducing P.V.C (25mm x 20mm ) to smaller sizes. Nos 119
Q208 Supplying & fixing tees reducing P.V.C (32mm x 25mm) to smaller sizes. Nos 121
Q209 Supplying & fixing tees reducing P.V.C (40mm x32mm) to smaller sizes. Nos 194
Q210 Supplying & fixing tees reducing P.V.C (50mm x 40mm) to smaller sizes.
Nos 277
Q211 Supplying & fixing tees reducing P.V.C (63mm x 50mm) to smaller sizes. Nos 420
Q212 Supplying & fixing tees reducing P.V.C (90mm x 63mm) to smaller sizes. Nos 1,000
Q213 Supplying & fixing reducing tee P.V.C. ( 110mm x 63mm) Nos 2,065
Repair Sockets & Tees P.V.C
Q214 Supplying & fixing repair socket P.V.C 20mm. Nos 90

Valve Socket P.V.C
Q221 Supplying & fixing valve socket P.V.C 20mm. Nos 94
Item Basic Rate

Code 2020
Faucet Socket P.V.C
Q228 Supplying & fixing faucet sockets P.V.C 20mm. Nos 92
Tapered union without thread P.V.C
Q235 Supplying & fixing tapered union without thread P.V.C 20mm. Nos 622
Q236 Supplying & fixing tapered union without thread P.V.C 25mm. Nos 1,005
Q242 Supplying & fixing tapered union with thread for P.V.C and metal pipe
connection 20mm. Nos 333
Q243 Supplying & fixing tapered union 25mm with thread for P.V.C & metal pipe
connections. Nos 438
connections. Nos 1,483
connections. Nos 2,060
Equal tees-P.V.C
Q249 Supplying & fixing tees equal P.V.C 20mm. Nos 92
Plugs, sockets-P.V.C
Q256 Supplying & fixing plugs P.V.C 20mm. Nos 95
Q258 Supplying & fixing plugs P.V.C 32mm Nos 116
Item Basic Rate

Code 2020
Q261 Supplying & fixing Plugs P.V.C 63mm. Nos 200

Q263 Supplying & fixing sockets plain P.V.C 20mm. Nos 87
Pipes P.V.C
Q270 Supplying & fixing pipes P.V.C, 20mm dia.(PNT 11)- PE.(Fittings paid
separately). m 85
Q271 Supplying & fixing pipes P.V.C, 25mm dia..(PNT 11)- PE (Fittings paid
separately). m 177
Q272 Supplying & fixing pipes P.V.C, 32mm dia..(PNT 11)- PE(Fittings paid
separately). m 417
Q273 Supplying & fixing pipes P.V.C, 40mm dia. .(PNT 11)- PE(Fittings paid
separately). m 531
Q274 Supplying & fixing pipes P.V.C 50mm dia. .(PNT 11)- PE (Fittings paid
separately). m 672
Q275 Supplying & fixing pipes P.V.C, 63mm dia..(PNT 11)- PE (Fittings paid
separately). m 1,050
Q276 Supplying & fixing pipes P.V.C 90mm dia. .(PNT 11)- PE (Fittings paid
separately). m 1,919
Pipes P.V.C (25% pipe cost included for Specials)
m
Q277 Supplying & fixing pipes P.V.C, 20mm dia. .(PNT 11) including specials. (25%
pipe cost included for Specials) m 108
pipe cost included for Specials) m 1,282
Flexible cord (S--Lon or Equivalent))
Q283 Supplying and fixing flexible cord -300mm (S-lon or equivalent) Nos 351

Item Basic Rate

Code 2020
Flexible hose
Q288 Supplying and fixing 20mm dia: Flexible hose (American Standard or
Equivalent.) 450mm long Nos 1,251
Prome cost Rs. 1080.00 80751
Plastic gully
Q289 Supplying & fixing plastic gully grating 150mm x150mm. Nos 210
Q290 Providing Catch pit 150mm x150mm x75mm in cement mortar. Nos 739
Elbows for down pipe.
Q291 Supplying & fixing P.V.C. elbows for down pipe. Nos 593
Running head.
Q292 Supplying & fixing P.V.C. running head. Nos 660
Gutter end.
Q293 Supplying & fixing or replacing, only a square type P.V.C. gutter ends. Nos 460
Gutter Joint.
Q294 Supplying & fixing or replacing, only a square type P.V.C. gutter joints. Nos 465
Eves gutters (PVC)-Square type
Q295 Supplying and fixing eves gutters square type PVC with necessary specials,
including running heads, miter joints, gutter joints, gutter brackets, gutter ends
etc. m 807
Down pipes P.V.C
Q296 Supplying & fixing rain water down pipes P.V.C to wall, with necessary
specials, including elbows, sockets, clips etc. m 705

Item Basic Rate

Code 2020
R-MECHANICAL INSTALLATIONS
Unitary Air Conditioning Equipments
Air Cooled inverter Type wall mounted split air conditioners such as L.G.,
Mitsubishi, Daikin or quivelant (refrigerant zero ODP) of cooling capacity as
specified (direct expansion) c/w Refrigerant Piping, Drain line, Insulation, Drain
pumps, control, brackets and Condensing units c/w motors, compressors,
condenser, copper tubes and pre-painted anti-corrosion resin coated aluminium
fins, blowers, filter drier, refrigerant..(Refrigirat pipe length of 5m considered
inclusive to the rate)
R001 9000 Btu/Hr Nos 128,150

R002 12000 Btu/Hr Nos 133,500
R003 18000 Btu/Hr Nos 154,900
R004 24000 Btu/Hr No. 178,350
Air Cooled non inverter Type wall mounted split air conditioners such as L.G.,
fins, blowers, filter drier, refrigerant.(Refrigirat pipe length of 5m considered
inclusive to the rate.)
R005 9000 Btu/Hr Nos 120,660

R006 12000 Btu/Hr Nos 130,825
R007 18000 Btu/Hr Nos 149,550
R008 24000 Btu/Hr Nos 209,850
Air Cooled inverter Type Ceiling mounted split air conditioners such as L.G.,
R009 18000 Btu/Hr Nos 310,050

R010 24000 Btu/Hr Nos 404,100
R011 36000 Btu/Hr Nos 467,100
R-1 This BSR is for construction works only

Item Basic Rate

Code 2020
Air Cooled non inverter Type Ceiling mounted split air conditioners such as
L.G., Mitsubishi, Daikin or quivelant (refrigerant zero ODP) of cooling capacity
as specified(direct expansion) c/w Refrigerant Piping, Drain line, Insulation,
Drain pumps, control, brackets and Condensing units c/w motors, compressors,
R012 18000 Btu/Hr Nos 272,600

R013 24000 Btu/Hr Nos 309,600
R014 36000 Btu/Hr Nos 377,850
Air Cooled inverter Type Ceiling Suspended 4 Way Cassete split air conditioners
such as L.G., Mitsubishi, Daikin or quivelant (refrigerant zero ODP) of cooling
capacity as specified (direct expansion) c/w Refrigerant Piping, Drain line,
Insulation, Drain pumps, control, brackets and Condensing units c/w motors,
compressors, condenser, copper tubes and pre-painted anti-corrosion resin coated
aluminium fins, blowers, filter drier, refrigerant.(Refrigirat pipe length of 5m
considered inclusive to the rate.)
R015 12000 Btu/Hr Nos 261,900

R016 18000 Btu/Hr Nos 285,100
R017 24000 Btu/Hr Nos 362,100
R018 36000 Btu/Hr Nos 519,600
Air Cooled non inverter Type Ceiling Suspended 4 Way Cassete split air
conditioners such as L.G., Mitsubishi, Daikin or quivelant (refrigerant zero ODP)
of cooling capacity as specified (direct expansion) c/w Refrigerant Piping, Drain
line, Insulation, Drain pumps, control, brackets and Condensing units c/w
motors, compressors, condenser, copper tubes and pre-painted anti-corrosion
resin coated aluminium fins, blowers, filter drier, refrigerant.(Refrigirat pipe
length of 5m considered inclusive to the rate.)
R019 18000 Btu/Hr Nos 272,600

R020 24000 Btu/Hr Nos 309,600
R021 36000 Btu/Hr Nos 377,850
Air Cooled inverter Type Ceiling mounted ducted type split air conditioners such
as L.G., Mitsubishi, Daikin or quivelant (refrigerant zero ODP) of cooling
R022 12000 Btu/Hr Nos 265,645

R023 18000 Btu/Hr Nos 276,345
R024 24000 Btu/Hr Nos 323,775
R025 36000 Btu/Hr Nos 476,025
Item Basic Rate

Code 2020
Air Cooled non inverter Type Ceiling mounted ducted type split air conditioners
such as L.G., Mitsubishi, Daikin or quivelant (refrigerant zero ODP) of cooling
R026 12000 Btu/Hr Nos 181,550

R027 18000 Btu/Hr Nos 201,445
R028 24000 Btu/Hr Nos 255,525
R029 36000 Btu/Hr Nos 255,525
Medical Grade Copper Pipes and Fittings
Medical grade Phosphorous De-Oxidized, Degreased and Non-Arsenical Copper
pipes, Pipe Fittings and valvescompied to BSEN 13348, Joint shall normally be
made on site by silver copper phosphate brazing using British Standard 1845 type
AG 14 alloy and fittings shall be of the "high duty" type suitable for steam
service gauge pressure up to 17 bars.
Medical Grade Copper Pipes
R030 15 mm diameter m 1,493
Lockable Line Valves
R035 15 mm diameter
Nos 11,520
R036 22 mm diameter
Nos 13,095
R037 28 mm diameter
Nos 22,335
R038 35 mm diameter
Nos 31,575
R039 42 mm diameter
Nos 45,585
90 Degree Elbow
R040 End Feed 15mm x 90 Degree Elbow Nos. 141
R041 End Feed 22mm x 90 Degree Elbow
Nos. 301
R042 End Feed 28mm x 90 Degree Elbow Nos. 469
R043 End Feed 35mm x 90 Degree Elbow Nos. 1,415
R044 End Feed 42mm x 90 Degree Elbow Nos. 2,359
Couplings
R045 End Feed 15mm Coupling Nos 164

Item Basic Rate

Code 2020

Equal Tee
R050 End Feed 15mm Equal Tee Nos 256
R051 End Feed 22mm Equal Tee Nos 669
R052 End Feed 28mm Equal Tee Nos 1,038
Reducing Coupling
R055 End Feed 22mm x 15mm Fitting Reducer Nos 822
R056 End Feed 28mm x 15mm Fitting Reducer Nos 1,466
Reducing Tee
R061 End Feed 22mm x 15mm Fitting Reducer Nos 859
Brass Munsen Rings - Single Ring M10
R067 15mm Brass Munsen Ring Tapped M10 Nos 728
FRESH AIR DUCTING WORK
pre-insulated supply air duct works including all bends, reducers, flange joints,
silicon sealant for all joints, anti vibration joint, Reinforcements, hangers etc…..
R072 100 x 100 mm m 2,333

R073 150 x 100 mm m 2,841
R074 150 x 150 mm m 3,349
R075 200 x 150 mm m 3,857
R076 500 x 150 mm m 8,570
R077 200 x 200 mm m 5,344
R078 250 x 200 mm m 5,485
R079 300 x 200 mm m 6,270
R080 350 x 200 mm m 7,309
R081 400 x 200 mm m 7,940
R082 500 x 200 mm m 9,200
R083 200 x 250 mm m 5,974

Item Basic Rate

Code 2020
R084 300 x 250 mm m 7,309

R085 400 x 250 mm m 8,645
R086 550 x 250 mm m 9,691
R087 575 x 250 mm m 10,852
R088 650x 250 mm m 11,797
R089 675 x 250 mm m 12,112
R090 700 x 250mm m 12,427
R091 900 x 250 mm m 14,949
R092 300x 300 mm m 8,015
R093 400 x 300 mm m 8,674
R094 500 x 300 mm m 10,536
R095 675 x 300 mm m 12,743
R096 700 x 300 mm m 13,057
Fire Detection System
Conventional Type Fire alarm control/indicating panel( (UL/LPCB approved,
NFPA 72/EN 54 complied) ) c/w contacts/auxiliary contacts( control modules,
monitoring modules) for shut down of A/C & ventilation equipment, connection
of fire link/lift homing and all necessary accessories (including battery backup,
design for the fire alarm control system, training & providing all passwords);
R097 Panel of 4 zones or less Nos 173,150

R098 Panel of 5-8 zones Nos 251,700
R099 Panel of 9-12 zones
Nos 318,250
R100 Panel of 12 zones or more
Nos 398,225
Automatic addressable Type Fire alarm control/indicating panel( (UL/LPCB
approved, NFPA 72/EN 54 complied) ) c/w contacts/auxiliary contacts( control
modules, monitoring modules) for shut down of A/C & ventilation equipment,
connection of fire link/lift homing and all necessary accessories (including
battery backup, design for the fire alarm control system, training & providing all
passwords)
R101 Panel of 50 points or less Nos 345,150
R102 Panel of 51 points to 100
Nos 431,700
R103 Panel of 101 points to 200
Nos 648,250
R104 Panel of 201 or higher Nos 828,225
Analogue Addressable Type smoke detector with multiple sensitivity (adjustable
at site) levels, programmable for timed automatic sensitivity selection with base,
Junction box and other accessories as required.
R105 Ionization Type Nos 8,090
R106 Optical Type (Photoelectric Type)
Nos 8,990

Item Basic Rate

Code 2020
Conventional Type smoke detector with multiple sensitivity (adjustable at site)

levels, programmable for timed automatic sensitivity selection with base,
R107 Ionization Type
Nos 7,490
Nos 8,390
Analogue Addressable Type duct detector with multiple sensitivity (adjustable at
site) levels, programmable for timed automatic sensitivity selection with base,
R110 Optical Type (Photoelectric Type) Nos 7,940
Conventional Type duct detector with multiple sensitivity (adjustable at site)
levels, programmable for timed automatic sensitivity selection with base,
Nos 9,690
Analogue Addressable Type heat detector with standard base and fixing
accessories.
R113 Rate-of-rise (ROR) Heat Detectors Nos 7,390
R114 Fixed Temperature Heat Detectors Nos 7,490
Conventional Type heat detector with standard base and fixing accessories.
R115 Rate-of-rise (ROR) Heat Detectors Nos 7,390
R116 Fixed Temperature Heat Detectors Nos 7,490
R117 Automatic/manual fire alarm call points c/w re-programming work of existing
addressable fire control panel, if necessary, and all necessary mounting
accessories and connected to the fire alarm control panel Nos 15,280
R118 Analogue Addressable Type Fault isolator module capable of monitoring shorted
loop circuit and automatically restore communications when shorted conditions
are corrected. Nos 9,140
R119 Addressable Manual pull station having an integrally mounted addressable
module that monitors and reports contact status. Nos 8,390
R120 Emergency Exit Lights and Emergency Exit Signs with 3hrs battery back up and
all necessary accessories. Nos 13,335
R121 2 x 2.5 sq. mm, fire resistance screened cable with PVC insulated copper wires
confirming to specification with polycon rigid and flexible conduits in inside the
walls, floor or ceiling. Nos 1,116
R122 2 x 1.5 sq. mm, fire resistance screened cable with PVC insulated copper wires
confirming to specification with polycon rigid and flexible conduits in inside the
walls, floor or ceiling. Nos 1,089

Item Basic Rate

Code 2020
S-ELECTRICAL INSTALLATION
Recommended makes of Electrical Accessories
MCCB:- Schneider, ABB, Terasaki, Siemens or equivalent.
MCB’S & RCCB’S:- Schneider , Siemens, Crabtree, Eaton, Hager, Moeller,
Legrand, F & G (Austria) or equivalent.
Cable :- ACL, Kelani, Sierra or equivalent.

Ceiling Fan:- K.D.K., National-Japanese origins
Exhaust Fan:- K.D.K., National-Japanese origins
Switch & socket outlet :- Tenby, Clipsal, MK, Crabtree, PDL, Kevilton, Orange
or Equivalent.
LED Fittings/ Tube:- The light should be good quality, Philips, DIMO, OSRAM
or approved equivalent. Minimum efficacy at scotopic condition should be above
100 lumen/W Corelate colour temperature (CCT) should be above 4000K, (Cool
White). Colour rendering index (CRI) should be above 80. Rated life time should
be above 50,000 hrs.
Distribution Board:- Shall be in surface mount metal enclosure fabricated
With Zinc coated sheet metal of gauge not less than 1.8 mm total enclosed, with
hinged door with protective cover plate for terminals, finished with powder
coating of approved colour and components as specified in the BOQ.
Energy Saving Bulbs:- CFL Builbs should be 5 stars

Recommended Fabricators of Switch boards and Enclosures.
Elsteel
K.I.K. Lanka (Pvt) Ltd
Pubudu Engineering (pvt) Ltd
Richardsons Projects (pvt) Ltd
Bentota Power Generators (Pvt) Ltd
OS Project (Pvt) Ltd. (Orange)
Or similar product
In PVC conduit
Point wiring to be carried out with 2x1mm2 PVC/PVC/CU + 2.5mm2 PVC/CU
earth cable terminated in a 3 terminal ceilingrose and sunk switch, wired in
concealed conduit in wall and above ceiling to be supplied and installed to
working order
S001 Lamp point wiring Nos. 2,726
S002 Water tight lamp point wiring Nos. 2,770
S003 Indoor Braacket lamp point wiring Nos. 2,715
S004 Stair way lamp point wiring controlled by 2 No. two way switches Nos. 4,445
S005 Ceiling fan point wiring complete with hook and sunk switch Nos. 3,307
wiring to be carried out with 2C,2.5mm2 PVC/PVC/CU + 2.5mm2 PVC/CU
earth cable wired in concealed conduit in wall and above ceiling to be supplied
and installed to working order
S006 13 AMP switch socket outlet Nos. 4,276
S-1 This BSR is for construction works only

Item Basic Rate

Code 2020

S008 15 AMP switch socket outlet c/w 20A DP Switch with Neon Indicator Lamp Nos. 6,758
In PVC Casing
point wiring to be carried out with 2x1mm2 PVC/PVC/CU + 2.5mm2 PVC/CU
earth cable terminated in a 3 terminal ceiling rose and sunk switch, wired with
PVC casing on wall and on soffit to be supplied and installed to working order.
S009 Lamp point wiring Nos. 3,029

S010 Water tight lamp point wiring Nos. 3,073
S011 Indoor Bracket lamp point wiring Nos. 3,018
S012 Stair way Lamp point wiring controlled by 2 No. two way switches. Nos. 4,983
S013 Ceiling fan point wiring complete with fan hook and sunk switch. Nos. 3,610
Wiring to be carried out with 2C,2.5mm2 PVC/PVC/CU + 2.5mm2 PVC/CU
earth cable wired in concealed conduit in wall and above ceiling to be supplied
and installed to working order
S014 13 AMP switch socket outlet (Radial Circuit) Nos. 4,566
S016 15 AMP switch socket outlet c/w 20A DP Nos. 7,480
Distribution Boards
Supply, Wiring and Installation of distribution board in surface mount plastic
enclosure with the undermentioned switch gears to working order.
S017 6 way SP & N Distribution board complete with 30AMP 2P MCB and 40A 2P
RCD(30mA) Nos. 9,549
RCD(30mA) Nos. 10,842
RCD(30mA) Nos. 13,034
RCD(30mA) Nos. 14,433
RCD(30mA) Nos. 16,742
RCD(30mA) Nos. 18,687
RCD(30mA) Nos. 13,801
RCD(30mA) Nos. 15,094
RCD(30mA) Nos. 17,392
RCD(30mA) Nos. 18,801
RCD(30mA) Nos. 21,647
RCD(30mA) Nos. 22,939

Item Basic Rate

Code 2020
S029 Suppling and Installation of TP & N Distribution board complete with 60 A 4P

MCB(10 kA) and 2 No. 32 A 3P MCB (10kA) in surface mount plastic
enclosure. Nos. 17,572
MCCB (25 kA) and 4 No. 16 A 3P MCB(10 kA) in surface mount metal
MCCB 925 kA) and 2 No. 30/60AMP 3P MCCB (kA) in surface mount metal
MCCB (25 kA) and 4 No. 30/60AMP 3P MCCB (25 kA) in surface mount metal
S033 Suppling and Installation of 20-100AMP 4P MCCB in surface mount metal
enclosure Nos. 20,922
S034 Suppling and Installation of 30AMP 2P isolator complete with plastic enclosure.
Nos. 3,094
Nos. 3,367
Nos. 5,581
Nos. 6,248
S038 Suppling and Installation of 40AMP 2P RCCB (30mA) complete plastic
Cabling in conduits
Cable shall be PVC/PVC/CU unless other wise specified to be supplied and
installed in conduit to working order.
S042 2x1 sq. mm + 2.5 sq. mm E cable m 193
S043 2x2.5 sq. mm + 2.5 sq. mm E cable m 348
S045 2x6 sq. mm + 6 sq. mm E cable m 742
S046 2x10 sq. mm + 10 sq. mm E cable m 1,133
S049 4x2.5 sq. mm + 2.5 sq. mm E cable 529
m
S052 4x10 sq. mm +10 sq. mm E cable 1,808
m
Item Basic Rate

Code 2020
S053 4x16 sq. mm +16 sq. mm E cable

m 2,529
S054 4x25 sq. mm +16 sq. mm E cable m 3,894
Unarmoured Cabling
Cable shall be Cu/PVC/PVC OR Cu/XLPE/PVC supplied and installed in
conduit or presure pipe (type 1000) to working order.
S056 2C Cu/PVC/PVC 1.5 sq. mm + 2.5 sq. mm E cable m 475
S057 2C Cu/PVC/PVC 2.5 sq. mm + 2.5 sq. mm E cable m 621
S058 2C Cu/PVC/PVC 4 sq. mm + 2.5 sq. mm E cable m 1,092
S059 2C Cu/PVC/PVC 6 sq. mm + 6 sq. mm E cable m 1,448
S064 4C Cu/PVC/PVC 16sq. mm + 16 sq. mm E cable m 3,616
S066 4C Cu/XLPE/PVC 35 sq. mm + 16 sq. mm E cable m 5,477
Armoured Cabling
Cable shall be Cu/XLPE/SWA/PVC (BS 5467 : 1997 600/1000V) supplied and
installed in cable tile with necessary accessories & materials to working order.
S070 4C Cu/XLPE/SWA/PVC 25 sq. mm m 5,313

Cabling in PVC Casing
Cable shall be PVC/PVC/CU unless other wise specified to be supplied and
installed in PVC casing to working order.
Item Basic Rate

Code 2020

Lightning Protection System
S092 Supplying and Installation of earth Electrode c/w 50 mm dia. Of 2 LM to
working order complete with forming of a gulley around the pipe. Nos. 4,455
S093 Supplying and Installation of 16 mm dia.solid copper earth rod with inspection
pit of 300mm x 300mm x 300mm Nos. 30,296
S094 Supply and Installation of 25mm x 3mm Cu tape in Air termination system Nos. 2,083
S095 Supply and Installation of 25mm x 3mm Cu tape in Down conductor system Nos. 2,179
S096 Supply and Installation of test joint mounted in a yellow PVC enclosure Nos. 3,535
S097 Supply and Installation of finial type air terminal with minimum 1000mm height
and 12mm diameter Nos. 15,892
Luminaire and Fixtures
Supplying and Installation of Luminaire and fixtures complete with all fixing
accessories, G.I. Chains cup hook 2/3 core cable, conector suspension holder etc.
to working order.
S098 Pendent Lamp C/W 250 mm dia. Conical plastic shade and 15W CFL bulb
(Prime cost for plastic shade -Rs. 350) Nos. 1,349
S099 Pendent Lamp C/W 200 mm dia. Glass globe and 15W CFL bulb (Prime cost for
pendant lamp c/w 200mm dia. Glass globe -Rs.1650) Nos. 2,574
S100 Indoor Bracket lamp C/W ornament shade and 15W CFL bulb (Prime cost for
bracket lamp c/w ornament shade -Rs. 1850) Nos. 2,699
S101 Water tight bracket lamp C/W Clear glass ornament shade and 15W CFL bulb(4
star rated) (Prime cost for water tight bracket lamp c/w ornament shade -Rs.
2750) Nos. 3,581
S102 Recessed type, T8 LED tube light fitting 1200mm x 300mm complete with
polished aluminium double parabolic louver and 2x18W LED tube. (Prime cost
for complete lamp fitting set with all accessories -Rs. 6775) Nos. 7,570
for lamp fitting set with all accessories -Rs.10150) Nos. 11,029
for lamp fitting set with all accessories -Rs. 8050) Nos. 8,877
for lamp fitting set with all accessories -Rs.7150) Nos. 7,954
S106 1200mm battern type T8 LED tube light (1x18W tube) fitting.(Prime cost for
lamp fitting set with all accessories -Rs. 2250) Nos. 2,773

Item Basic Rate

Code 2020
S107 1200mm battern type T8 LED tube light (2x18W tube) fitting. (Prime cost for
lamp fitting set with all accessories -Rs. 3950) Nos. 4,728
S108 600mm battern type T8 LED tube light (1x9W tube) fitting. (Prime cost for lamp
fitting set with all accessories -Rs. 1780) Nos. 2,498
S109 1200mm Suspension type T8 LED tube light complete with prismatic diffuser
and (1x18W tube) (Prime cost for lamp fitting set with all accessories -Rs. 3250)
Nos. 4,010
S110 600mm Suspension type T8 LED tube light complete with prismatic diffuser and
(1x9W tube)(Prime cost for lamp fitting set with all accessories -Rs. 2500)
Nos. 3,086
S111 1200mm Suspension type T8 LED tube light complete with prismatic diffuser
and (2x18W tube) (Prime cost for lamp fitting set with all accessories -Rs. 4950)
Nos. 5,597
S112 Recessed type 6W LED panel light fitting (Prime cost for Recessed down light -
Rs.775) Nos. 1,247
S113 Recessed type12W LED panel light fitting (Prime cost for Recessed down light -
Rs. 1200) Nos. 1,683
S114 Recessed type 18W LED panel light fitting (Prime cost for Recessed down light -
Rs. 1500) Nos. 1,991
S115 Recessed mounted 6W Down light (Prime cost for Recessed down light -Rs.
1850) Nos. 2,363
S116 Recessed mounted 12W Down light (Prime cost for Recessed down light -Rs.
2950) Nos. 3,490
S117 Bulk head lamp water tight C/W 18W CFL bulb (4 star rated) (Prime cost for
Recessed down light -Rs. 2250) Nos. 3,441
S118 10W IP 65 flood light Nos. 3,658
Switch socket outlet
Switch socket outlet 5AMP/13Amp/15AMP to be supplied and installed
Supplying and fixing sunk switch
Supplying and fixing sunk switch complete with plastic sunk box to be supplied
S124 Supplying and fixing 1 gang sunk switch Nos. 535
S127 Supplying and fixing 4 gang sunk switch Nos. 1,118
S128 Supplying and fixing 5 gang sunk switch Nos. 1,346
S129 Supplying and fixing fan regulator dimmer type Nos. 1,406
S130 Supplying and fixing Ceiling fan regulator Nos. 1,678
S131 Supplying and fixing 20 AMP DP switch with Neon indicator 2,312
Nos.
S132 Supplying and fixing sunk Bell push Nos. 656
S133 Supplying and fixing Cell Bell Ding Dong type excluding wires Nos. 962

Item Basic Rate

Code 2020
Fans
Supply & Installation of Ceiling fan 1400mm dia. Complete with 3 speed
S134
regulator (Excluding wiring) Nos. 9,236
Exhaust Fans
S135 Supply & Installation of 200mm dia. Exhaust fan with auto shutter (K.D.K or
equvalent) (Excluding wiring) Nos. 5,188
Wall Fans
S139 Supply & Installation of wall fan 450mm dia. Complete with 3 speed regulator
(Excluding wiring) Nos. 12,201
Conduit Pipe
Supplying & installation of conduit pipe clipped in surface
S140 18mm conduit pipe
m 84
S141 20mm conduit pipe m 88
S142 25mm conduit pipe 102
m
PVC Casing
Supplying and Installation of PVC casing

S146 10mmx20mm PVC Casing m 122
S150 50mmx25mm PVC Casing
m 343
S151 50mmX50mm PVC Box Casing
m 467
S152 50mmX75mm PVC Box Casing
m 607
S153 100mmX50mm PVC Box Casing m 914
S154 100mmx27mm PVC Box Casing
m 637
Supply and Installation of main cables
S155 2x1 sq. mm Cu/PVC/PVC Cable m 135
S156 2 x 2.5 sq. mm Cu/PVC/PVC Cable m 281
S157 2 x 4 sq. mm Cu/PVC/PVC Cable m 401

Item Basic Rate

Code 2020

S160 2 x 16 sq. mm Cu/PVC/PVC Cable m 1,186
S162 2 x 35 sq. mm Cu/PVC/PVC Cable m 2,335
Supply and Installation of Earth cables
S163 2.5 sq. mm Cu/PVC Earth cable m 125
S164 4 sq. mm Cu/PVC Earth cable m 207
S168 25 sq. mm Cu/PVC Earth cable m 1,142
S169 35 sq. mm Cu/PVC Earth cable
m 1,477
S171 70 sq. mm Cu/PVC Earth cable 2,550
m
S173 120 sq. mm Cu/PVC Earth cable
m 4,192
SUPPLY & INSTALLATION OF DOL STARTER
S174 Single phase DOL starter for 5.5kW motor (without overload) Nos. 14,369
S175 Three phase DOL starter for 5.5kW motor (without overload) Nos. 47,732
EXTRA LOW VOLTAGE SYSTEM
Supply and installation of Cat6 Data Outlet for Data points including Cat6
cables, Cat6 Keystone Jacks, Single face plates, Sunk Box, PVC
S176
Conduits/Trunking, Floor Trunking and all other accessories to be supplied and
installed to working order Nos. 6,815
Supply and Laying of Solid Pure Copper CAT 6 Cable from a relevant Patch
S177
Panel to each Camera point Nos. 4,667
MM OM3 6-Core Outdoor Armed Fiber Optic Cables supplied and installed in a
S178
trench including all required civil works and installation charges Nos. 2,706
MM OM3 8-Core Outdoor Armed Fiber Optic Cables supplied and installed in a
S179
trench including all required civil works and installation charges Nos. 2,812
MM OM3 12-Core Outdoor Armed Fiber Optic Cables supplied and installed in
S180
a trench including all required civil works and installation charges Nos. 3,024
Supply and Installation of 12 Core Optic Fiber indoor MM 50/125 OM3 through
S181 securely fixed PVC Pipes and casings ( runs per floor Access switches, starting
from Core switches) Nos. 2,574
S184 Supply and Laying of Solid Pure Copper CAT 6 Cable Nos. 1,190
S185 Supply and installation of fiber patch cords ( 1m ) Nos. 2,231
Item Basic Rate

Code 2020
S186 0.5m Solid Pure Copper CAT 6 Slim Boot Patch Cords. Nos. 499
S187 1m Solid Pure Copper CAT 6 Slim Boot Patch Cords. Nos. 604
S188 3m Solid Pure Copper CAT 6 Slim Boot Patch Cords. Nos. 814
Supply and Installation of 16U 19" wall mounting, glass door, fully loaded rack
with the following accessories.
4 way power bar with 13A socket outlets. Thermostatically controlled 3 nos
S189
100mmx100mm size 230Vac, cooling fan plate with finger guard, Vertical &
Horizontal cable trays,Gland plates top & bottom, Fixed trays, UK Plug etc.( As
per specifications ) Nos. 60,660
Supply and Installation of 25U 19" wall mounting, glass door, fully loaded rack
with the following accessories.
4 way power bar with 13A socket outlets. Thermostatically controlled 3 nos
S190
100mmx100mm size 230Vac, cooling fan plate with finger guard, Vertical &
Horizontal cable trays,Gland plates top & bottom, Fixed trays, UK Plug etc.( As
per specifications ) Nos. 90,417
Supply and installation of 12 Port POE 185W, Non blocking,
Manageable Switch with 12 x RJ-45 10/100/1000 Mbps Gigabit
S191
Ethernet Ports, 2 No. SFP ports as uplinks ,SFP transceivers and
any other connecting equipments for uplinks. having auto Crossover Function Nos. 279,030
S192
S193
Supply and installation of 16 Port Unmanageable Switch with 16 x RJ-45
S194
10/100/1000 Mbps Gigabit Nos. 28,150
S195
10/100/1000 Mbps Gigabit Nos. 41,410
S196
10/100/1000 Mbps Gigabit Nos. 104,810
S197 Supply and Installation of 12 port duplex SC port fiber Patch Panel Nos. 29,113
S198 Supply and Installation of 12 port Copper Patch Panel Nos. 7,250

Item Basic Rate

Code 2020
T -FINISHERG & FLOORING
T1-Plasterer
Plastering (walls)
T001 (15 mm) thick plastering to wall in cement lime and sand 1:1:5 finished semi
rough with wooden float. m2 714
T002 (15 mm thick plastering to wall in cement lime and sand 1:1:5 finished smooth
with lime putty floating. m2 831
T003 (15 mm)) thick plastering 1:5 cement and sand semi rough 2
m 634
Plastering (beams, slab soffits)
T004 10mm thick plastering to R.C.C. beams, slab soffit in cement and sand 1:3
including floating with lime putty. m2 940
T005 Cove moulding 62.5mm x 62.5mm in cement mortar 1:2 built in existing wall. m 337
T006 Cresting with broken glass in cement mortar 1:4 on coping of boundary wall. m 378
Moulding
T007 Moulding 75mm x 12mm in walls in lime and cement mortar 1:1:4 only for
replacements to match existing or to be "extra" over rate for plastering.
m 358
T008 Moulding 150mm x 25mm in walls in lime and cement mortar 1:1:4 only for
replacements to match existing or to be "extra" over rate for plastering.
m 536
T009 Moulding 100mm x 50mm in cement and sand 1:2 built in existing wall. m 707
T010 Flashing or plaster bands laid over tiles 100mm to 150mm wide on roof in
cement and lime mortar 1:1:4. m 230
T011 Letters embossed in plaster 20mm thick upto 150mm high in cement and sand
1:2 cement floated and painted complete. Nos 311
T012 16mm thick plastering to walls in lime and sand 2:5 including floating, finished
smooth with lime putty. m2 837
T013 Pointing flush in cement 1:2 in surface cracks including raking out joints. m 153
T014 Pointing, tuck, projected in cement 1:2 on brick masonry etc. m2 1,284
Rendering Cement
T015 Rendering Cement 12mm; 1:2 above 9.29m2. m2 672
T016 Rendering, cement 12mm, 1:2 upto 9.29m2. m2 772
T017 Rendering, cement 12mm, 1:3 above 9.29m2. 2
m 624
T018 Rendering, cement 12mm 1:3 upto 9.29m2. 2
m 724
T019 Rendering, cement 20mm, 1:2 above 9.29 m2. 2
m 933
T020 Rendering, cement 20mm, 1:2 upto 9.29m2. 2
m 1,065
T021 Rendering, cement 20mm 1:3 above 9.29 m2 . 2
m 877
T022 Rendering, cement 20mm, 1:3 upto 9.29 m2. 2
m 1,009
Cement floating coat.
T023 Rendering, cement, floating coat, using neat Cement and finished smooth with
Carborandum Stone. m2 150
T-1 This BSR is for construction works only

Item Basic Rate

Code 2020
T024 Rendering, cement, floating coat, using Red Cement finished smooth with
Carborandum stone. m2 243
T025 Rendering, cement, floating coat, using brown or green cement finished smooth
with Carborandum Stone. m2 204
T026 Rendering, cement, floating coat, using black cement finished smooth with
Carborandum Stone. m2 239
T027 Rendering cement 20mm 1:2 with Pudlo, 2.25kg to 45kg, cement. 2
m 977
Skirting in cement mortar
T028 Skirting in cement mortar 1:3, 12mm x 100mm projected or flushed with wall,
and including forming groove. m 464
T029 Skirting in cement mortar 1:3, 12mm x100mm projected or flushed with wall
finished with Red Cement floating, including forming groove. m 521
Plastering (Reveals)
T030 Plastering external reveals 0mm - 100mm wide finished rough. m 540
T031 Plastering internal reveals 0mm - 100mm wide finished smooth. m 673
T2-PAVIOR
T032 Expansion joints in brick floors, filling with bitumen and sand. m 90
T033 Expansion joints in concrete floors filling with bitumen and sand (to full depth of
concrete and rendering).6mm tk and 100mm deep. m 171
Floors, gravel
T034 Floors, gravel 100mm thick, spreading, watering and ramming. m2 192
Floor tiles (Laying only)
Fixing tiles on floors with all specials, including raking plaster and bedding in
cement mortar 1:3 pointed with tile grout to match the tiles. (Tiles supplied by
the client or paid separately.
T035 --Do-- for, tiles 200mm x 200mm in size. m2 1,610
T036 --Do-- for, tiles 300mm x 300mm in size. 2
m 1,604
T037 --Do-- for, tiles 400mm x 400mm in size. 2
m 1,527
T038 --Do-- for, tiles 600mm x 600mm in size. m2 1,432
Floor tiles; (Gloss/Semi Gloss/Matt) - Vitreous Porcelain (
#####
Homogenous/ Non Homogenous)-Local
Porcelain Homogenous/ Non Homogenous Vitreous, floor tiles with all specials
supplying and fixing to floors including raking plaster and bedding in cement
mortar 1:3 and pointed with tile grout to match the tiles. ( Rocell or equivalent
brand)
T039 '--Do-- for, 300mm x 300mm MATT floor tile m2 4,280
Prime Cost of, 12"x12" MATT floor tile (Rocell or Equivalent)Prime Cost of,
=226 #####
T040 '--Do-- for, 300mm x 300mm GLOSS floor tile
m2 3,919
Prime Cost of, 12"x12" GLOSS floor tile (Rocell or Equivalent)Prime Cost of,
=196 #####

Item Basic Rate

Code 2020
T041 --Do-- for, 300mm x 300mm SEMI GLOSS floor tile m2 3,587
Prime Cost of, 12"x12" SEMI GLOSS floor tile (Rocell or Equivalent)Prime
Cost of, =168 #####
T042 --Do-- for, 400mm x 400mm MATT floor tile m2 4,200
=396 #####
=520 #####
T044 --Do-- for, 500mm x 500mm GLOSS floor tile m2 4,431
Prime Cost of, 20"x20" GLOSS floor tile (Rocell or Equivalent)Prime Cost of,
=688 #####
=607 #####
T046 --Do-- for, 600mm x 300mm GLOSS floor tile m2 4,999
=607 #####
=730 #####
T048 --Do-- for, 600mm x 600mm POLISH floor tile m2 5,827
Prime Cost of, 24"x24" POLISH floor tile (Rocell or Equivalent)Prime Cost of,
=1470 #####
=1302 #####
T050 --Do-- for, 900mm x450mm MATT floor tile m2 4,988
=1292 #####
Floor tiles- Rustic Type ( Homogenous)-Local
Floor tiles- Rustic Type ( Homogenous), with all specials supplying and fixing to
floors including raking plaster and bedding in cement mortar 1:3 and pointed
with tile grout to match the tiles. ( Rocell or equivalent brand)
T051 --Do-- for, 300mm x 300mm in size. m2 4,304

Prime Cost of, Tiles 12"x12" Rustic Type ( Homogenius) ( Rocell )Prime Cost
of, =228 #####
T052 --Do-- for, 400mm x 400mm in size. m2 4,038
Prime Cost of, Tiles 16" x 16"Rustic Type ( Homogenius) ( Rocell )Prime Cost
of, =372 #####

Item Basic Rate

Code 2020
Tile Skirting #####

T053 Vitreous ceramic floor tiles Skirting 12"x4" supplying and fixing to bottom line
of wall including raking plaster bedding with cement mortar 1:3 and pointed with
tile grout to match the tiles. (Quality approved by the Engineer.) m 679
Prime Cost of, Tiles 16" x 16"Rustic Type ( Homogenius) ( Rocell )Prime Cost
of, =372 #####
Terrazzo tile flooring
T054 Terrazzo tile flooring supplying and laying.

m2 3,353
T055 Terrazzo, wall lining with precast walling slabs 37.5mm thick supplying and
fixing to complete. m2 3,277
Wall tiles -glazed ( Approved Quality)
T056 Tiles, glazed with all specials, supplying and fixing to walls including raking
plaster and backing in cement mortar 1:3. for available tiles (Tiles supplied by
the client or paid separately.) m2 1,549
Wall tiles -Local
T057 Boarder tiles glazed colour 300mm X 75mm, with decorative patterns , supplying
and fixing to walls including raking plaster backing in cement mortar 1:3 and m 987
pointed with tile grout to match the tiles.
Prime Cost of, Boarder tiles glazed colour 12 "x 3" with decorative
#####
patternsPrime Cost of, =242
T058 Boarder tiles glazed colour 300mm X 75mm, with decorative patterns , supplying
and fixing to walls including raking plaster backing in cement mortar 1:3 and m 1,344
pointed with tile grout to match the tiles.
Prime Cost of, Boarder tiles glazed colour 12 "x 3" with decorative patterns
#####
(extreme design)Prime Cost of, =341
Granite flooring-Local #####
T059 Granite floor tiles 300mm x 300mm x 12mm (Local) supplying and fixing to
floors including raking plaster bedding with cement mortar 1:3. m2 11,973
Prime Cost of, Granite floor tiles 12" x 12"x ½" (Local, Range 1)Prime Cost of,
=919 #####
T060 Granite floor tiles 600mm x 300mm x 20mm (Local) supplying and fixing to
floors including raking plaster bedding with cement mortar 1:3.
m2 17,062
Prime Cost of, Granite floor tiles 12" x 12"x ½" (Local, Range 1)Prime Cost of,
=919 #####
T061 Labour cost for fixing 300mm x 100mm x 12mm Granite skirting to bottom line
of walls including cutting ,rounding & Forming edges polishing etc. m 518
Glass block
T062 Glass block 200mm x 200mm with all specials supplying and fixing to walls
including raking plaster and bedding in cement mortar 1:3. m2 13,792

Item Basic Rate

Code 2020
Vinyl Sheet Flooring

#####
T063 Supplying and laying 2mm thick Vinyl Flooring with necessary adhesive etc.
(Mipolam 150 or equivalent) (Upto 14 m2 only) m2 4,575
Vinyl Tile
T064 Supplying and laying 2mm thick Vinyl tile with necessary adhesive etc. (Mactile
- Gerflor or equivalent) (Upto 14m2 only) m2 3,175
Loop pile carpeting
T065 Supplying and laying Loop pile carpeting with 5mm thick with Mcfoam under
layer , firmly bonded to the existing floor. Carpet having primary & Secondary
backings, namely polypropylene & Classic back respectively. And having the
minimum pile weight of 20 Oz-USA per sq. yard. & loop density of 6,100
2
Oz/Cu.yard. (Neyland II or equivalent) (Upto 14m2 only) m 1,722
Cut pile carpeting
T066 Supplying and laying 1/8 gauged, Wide Open Cut pile carpeting (USA or
equivalent) with 5mm thick with Mac Form under layer , firmly bonded to the
existing floor. Carpet having primary & Secondary backings, namely woven
polypropylene & Classic back polypropylene, respectively. And having the
minimum pile weight of 30 Oz per sq. yard. & loop density of 5320 Oz/Cu.yard.
(Upto 14m2 only) m2 3,272
Interlocking paving
T067 Supplying and Laying 80mm thick "Uni" type Coloured interlocking paving
blocks having Compressive Strength of 40N/mm2, layed on plain improved sub
surface. Rate inclusive for Quarry dust bedding (Upto 14m2 only)
m2 3,965
T068 Supplying and Laying 80mm thick "Uni" type Natural cement colour interlocking
paving blocks having Compressive Strength of 40N/mm2, layed on plain
improved sub surface. Rate inclusive for Quarry dust bedding. (Upto 14m2 only)
m2 3,722
Paving tile Slabs
T069 Supplying and Laying 300 x300 x50mm thick Non Reinforced, Natural cement
colour, Concrete paving Slab, layed on plain improved sub surface. Rate
inclusive for Quarry dust bedding. (Upto 14m2 only) m2 2,559
T070 Supplying and Laying 300 x300 x50mm thick Reinforced, Natural cement
colour, Concrete paving Slab, layed on plain improved sub surface. Rate
inclusive for Quarry dust bedding. (Upto 14m2 only) m2 3,527

Item Basic Rate

Code 2020
U-GLAZER
U001 Glass panes fixing with (Group 6 category A) timber beadings (Glass available)
m2 1,955
U002 Glass panes 3 mm clear supplying and fixing with (Group 6 category A) timber
beadings. m2 2,761
U003 Glass panes 5 mm clear, supplying and fixing with Teak Beadings. 2
m 3,223
U004 Glass panes 5 mm pinhead or obscure supplying and fixing with (Group 6
category A) timber beadings. m2 3,511
U005 Glass panes 3 mm pinhead or obscure supplying and fixing with (Group 6
category A) timber beadings. m2 2,415
U006 Paint removing from painted glass panes with Caustic Soda Solution or other
paint remover. m2 527
U-1 This BSR is for constuction works only

Item Basic Rate

Code 2020
V-PAINTING & DECORATING

V001 Walls, scraped to original plaster, sand papering and lime putting cracks and
defects, preparing surface for Distemper, snowcem, paint or similar application.
m2 143
V002 Walls, scraping and removing soot and levelling internally in Kitchen (extra over
colour washing) m2 40
Total coat / Skim coat
V003 Applying Total coat joint compound and wall filler two coats, finished smooth
with sand papering, and prepare for colour washing. m2 623
V004 Applying Skim Coat compound on walls or sofit two coats, finished smooth with
sand papering, and prepare for colour washing. m2 411
Cement washing to walls
V005 Cement washing to walls of single storeyed buildings, 1 coat, patching and
preparing surface. m2 42
V006 Cement washing to walls of single storeyed buildings, 2 coat, patching and
2
preparing surface. m 72
V007 Cement washing externally to walls of building with upper floors, 1 coat. 2
m 54
White or colour washing walls
V008 White or colour washing walls of single storeyed buildings 1 coat, including
patching up and preparing surface. m2 43
V009 White or colour washing walls of single storeyed buildings 2 coats, including
patching up and preparing surface. m2 75
V010 White or Colour washing external walls of two storeyed buildings, 1 coat. 2
m 50
V011 White or Colour washing external walls in buildings, of more than 2 storeys, 1
coat. m2 57
V012 White or Colour washing external walls in Two storeyed buildings, 2 coats. 2
m 89
V013 White or Colour washing external walls in building with more than 2 storeys, 2
coats. m2 96
Snowcem paint
V014 Painting walls with snowcem or equivalent cement paint, 2 coats to new work. m2 378
Alkali resisting primer
V015 Painting walls with alkali resisting primer where necessary. m2 237
Elastometic filler Primer
V016 Painting walls with one coat of Elastometic filler Primer where necessary. m2 182
Alkali resisting water Proofing sealer
V017 Painting walls with one coat of Alkali resisting water Proofing sealer where
necessary. m2 217
Anti-fungus paint
V018 Applying Anti-fungus paint to all exposed surfaces on walls already prepared.
m2 803
Silicone masonry water repellent paint
V019 Painting Walls with one coat of Silicone masonry water repellent paint. m2 149
Bathroom paint
V020 Painting Walls with one coat of Bathroom paint. m2 197
V-1 This BSR is for construction works only

Item Basic Rate

Code 2020
Emulsion paint
V021 Painting Walls with one coat of emulsion paint. (new work or after preparation of
old wall) m2 179
V022 Painting walls with two coats of emulsion paint. (new work or after preparation
of old wall) m2 326
Painting weather shied (External walls) on New work
V023 Painting external walls with One coat of weather shied paint. (On New work or
prepared old work). m2 307
V024 Painting external walls with Two coats of weather shied paint. (On New work
or prepared old work). m2 576
Acrylic Emulsion (Exterior paint)
V025 Painting external walls with two coats of Acrylic Emulsion paint resist against
algae, fungus and scrubs. m2 414
Painting asbestos sheet roof
V026 Painting over the asbestos sheet roof with coats of roof shield paint. m2 383
V027 Painting under side of asbestos roofing sheet with one coats of emulsion paint 2
m 251
V028 Painting under side of asbestos roofing sheet with two coats of emulsion paint 2
m 380
V029 Painting under side of asbestos roofing sheet with one coat of primer after
preparing surface m2 394
Floor Painting
V030 Painting floors with One coat of quick drying Floor paint including washing,
cleaning and smoothing down the surface. m2 288
V031 Painting floors with Two coats of quick drying Floor paint including washing,
cleaning and smoothing down the surface. m2 558
Anticorrosive paint
V032 Painting steelwork, 1 coat with anticorrosive paint including removing scale and
wire brushing. m2 214
V033 Painting steelwork, 2 coats, with anticorrosive paint including removing scale
and wire brushing. m2 392
Painting on GI Surface
V034 Painting new galvanized iron GI Adhesion Promoter one coat and one coat of
Dulux metal primer zink chromate or duco oil primer or equivalent including
washing surface with water after manufactures specification. m2 403
Aluminium paint
V035 Painting, aluminium paint, 1 coat on metal surfaces. m2 181
V036 Aluminium paint, one coat, along 50mm thick band. m 39
V037 Aluminium paint, two coat, along 50mm thick band. m 70
Enamel paint
V038 Painting one coat of Enamel paint, including washing and cleaning the surface. m2 231
V039 Painting two coat of Enamel paint, including washing and cleaning the surface. 2
m 429
Removal of Paint from timber.
V040 Paint removed entirely with blow lamp to bare timber. m2 273
V041 Painting G.I pipes 12mm to 20mm with approved paint, 2 coats. m 71
Wood preservative
V042 Wood preservative, (clear) applied to woodwork one coat (old work) m2 111
Item Basic Rate

Code 2020
V043 Wood preservative, (clear) applied to woodwork two coats (New work) m2 210
Enamel paint with Wood primer Under coat
V044 Painting new woodwork, with primer, undercoat and 2 coats of enamel paint. 2
m 716
V045 Painting new woodwork with approved primer, one coat. 2
m 240
Polishing wood work with Wax
V046 Wax polishing wood work including thoroughly sand papering surface in new
work only of permanent fixtures. m2 589
Painting with Wood sheen
V047 Painting with Wood sheen paint including washing cleaning and smoothing
down surface, One coat. m2 235
V048 Painting with wood sheen paint including washing cleaning and smoothing down
surface, Two coats. m2 400
Polyurethane Varnishing
V049 Varnishing with polyurethane varnish after washing down and sand papering, 1
coat. m2 302
coats. m2 499
polyurethane varnish-Matt
coats. m2 509
Removing Varnish
V052 Varnishing, removing entirely to bare timber and preparing surface. 2
m 348
Painting with Sanding sealer / Woof finish
V053 Applying new woodwork with two coats of Sanding sealer and two coats of
wood finish m2 634
V054 Applying wood finish, one coat, including washing, cleaning and smoothing
down surface. m2 261
V055 Applying wood finish, one coat, including two coats of sanding sealer after
washing, cleaning and smoothing down surface. m2 728
Painting with Perque varnish
V056 Cutting, levelling ,polishing and applying two coats of Perque varnish for an
2
existing timber base floor. m 1,328
V057 Applying masonry sealer for walls one coat. 2
m 227
Painting Letters on (Board / Wall)
V058 Lettering 25mm to 37.5mm painted in Sinhalese, English or Tamil, including
painting background. Nos 57
V059 Lettering 50mm to 75mm painted in Sinhalese, English or Tamil, including
V060 Lettering 100mm to 125mm painted in Sinhalese, English or Tamil, including

Item Basic Rate

Code 2020
W-DRAINAGE SYSTEMS
Wire dome (Steel)
W001 Wire domes for 63mm pipes supplying and fixing. Nos 318
W002 Wire domes for 110mm pipes supplying and fixing. Nos 371
Wire dome (PVC)
W003 Supplying & fixing PVC wire dome for 2"(50mm) dia. P.V.C drainage pipes.
Nos 250
W004 Supplying & fixing PVC wire dome for 4" (100mm)dia. P.V.C drainage pipes.
Nos 302
Drainage Fittings 4" (110mm) dia-(Local make)
W005 Supplying & fixing 110mm dia. P.V.C plain socket (Local make) Nos 950
W006 Supplying & fixing 110mm dia. P.V.C drainage elbow with single Door,
approved quality with rubber ring joint.(Locally made) Nos 1,223
W007 Supplying & fixing 110mm dia. P.V.C drainage bend 45 degree. (S-Lon or
W008 Supplying & fixing 110mm dia. P.V.C drainage bend 45 degree ,with single Door
(S-Lon or Equivalent.) Nos 1,093
W010 Supplying & fixing 110mm dia. P.V.C drainage bend 89 degree. With single
Door (S-Lon or Equivalent.) Nos 1,523
W011 Supplying & fixing 110mm dia. P.V.C drainage Tee. (S-Lon or Equivalent.) Nos 1,213
W012 Supplying & fixing 110mm dia. P.V.C drainage Swept Tee. (S-Lon or
W013 Supplying & fixing 110mm dia. P.V.C drainage Tee. with single Door (S-Lon or
W014 Supplying & fixing 110mm dia. P.V.C drainage Swept Tee. with single Door (S-
Lon or Equivalent.) Nos 1,543
W015 Supplying & fixing 110mm dia. P.V.C drainage "Y" junction (S-Lon or
W016 Supplying & fixing 110mm dia. P.V.C drainage "Y" junction with single Door
Drainage Fittings 2" (63mm) dia.
W018 Supplying & fixing 63mm dia. P.V.C drainage bend 45 degree, with single Door
(S-Lon or Equivalent.) Nos 653
W021 Supplying & fixing 63mm dia. P.V.C drainage Tee. (S-Lon or Equivalent.) Nos 723
W-1 This BSR is for construction works only

Item Basic Rate

Code 2020
W024 Supplying & fixing 63mm dia. P.V.C drainage "Y" junction with single Door (S-
Drainage Fittings 1½"or (50mm) dia
W026 Supplying & fixing 50mm dia. P.V.C drainage bend 45 degree with single Door
W029 Supplying & fixing 50mm dia. P.V.C drainage Tee. (S-Lon or Equivalent.) Nos 663
W030 Supplying & fixing 50mm dia. P.V.C drainage Swept Tee. (S-Lon or Equivalent.)
Nos 843
W032 Supplying & fixing 50mm dia. P.V.C drainage Swept Tee. with single Door (S-
W034 Supplying & fixing 50mm dia. P.V.C drainage "Y" junction with single Door (S-
Drain Pipes P.V.C, 4" or (110mm)dia, (PNT9)- lay in Trenches
W035 Drains, P.V.C, 110mm dia: (PNT9) laying on cement concrete 150mm thick
bedding up to 600mm depth of invert including excavation, back filling and
cement concrete hunching 1:3:6(25mm). m 3,369
W036 Drains P.V.C, 110mm dia. (PNT9) laying on cement concrete 150mm thick
bedding over 600mm. up to 1200mm. depth of invert including excavation back
filling and cement concrete hunching 1:3:6(25mm). m 3,631
W037 Drains P.V.C, 110mm dia. (PNT9) laying on cement concrete 150mm thick
bedding over 1200mm. up to 1800mm. depth of invert including excavation
back filling and cement concrete hunching 1:3:6(25mm). m 4,415
Drain Pipes P.V.C, 6" or (160mm)dia, (PNT9)- lay in Trenches
W038 Drains PVC, 160mm dia. (PNT9) laying on cement concrete 150mm thick
bedding up to 600mm. depth of invert including excavation , backfilling and
cement concrete hunching 1:3:6 (25mm). m 4,874
W039 Drains PVC, 160mm dia.( PNT9 ) laying on cement concrete 150mm thick
bedding over 600mm up to 1200mm depth of invert including excavation
backfilling and cement concrete hunching 1:3:6 (25mm ). m 5,146
bedding 1200mm up to 1800mm depth of invert including excavation backfilling
and cement concrete hunching 1:3:6 (25mm) . m 5,920
Item Basic Rate

Code 2020
Drain Pipes P.V.C, 12" or (315mm)dia, (PNT9)

bedding over 600mm up to 1200mm depth of invert including excavation
backfilling and cement concrete hunching 1:3:6 (25mm ). m 14,114

Item Basic Rate

Code 2020
X-EXTERNAL WORKS
Fencing
X001 Fence barbed wire, 12 1/2 gauge, 4 points, 75mm apart, supplying & fixing on
existing timber posts with G.I staples. m 39
X002 Fence, Barbed wire 12 1/2 gauge, 4 points, 75mm apart, supplying & fixing on
existing concrete posts with available hook bolts. m 42
X003 Fence posts or struts, Milla, Na, Palu or Satin 100mm to 150mm average dia.
supplying and fixing in ground complete, inclusive of sharpening and tarring. m 734
X004 Intermediate fence posts or struts, cement concrete 1: 1½ :3 (20mm) reinforced
with 4 Nos. 6mm (1/4")dia. M.S rods, 1700mm high square section 100mm to
150mm supplying and fixing complete as per drawing No. 68 of 22.07.1936.
Nos 1,860
X005 Intermediate fence posts or struts, cement concrete 1: 1½ :3 (20mm) reinforced
with 4 Nos. 6mm (1/4") dia. M.S rods, 1700mm high square section 100mm to
150mm supplying and fixing complete as per drawing No. 68 of 22.07.1936.
Nos 2,170
X006 End post and strut for Type barbed wire fence supplying and fixing complete in
cement concrete as per drawing No. 68 of 22.07.1936. Nos 10,546
X007 Fence, bared wire, 5 strands, 12 1/2 B.W.G with 4 points at 75mm centers and
R.C. posts (1:2:4) 20mm metal, reinforced with 4 Nos. 6mm rods with No. 14
B.W.G stirrups at 200mm centers. Post to be fixed at 2400mm centers including
excavation, cement concrete foundation 1:3:6 (40mm) metal to corner posts and
struts, and straining bolts. Struts to be reinforced with 4 Nos. 10mm roads and
corner posts with 4 Nos. 12mm roads. m 1,421
X008 Straining Bolts, 450mm long 12mm dia. making and fixing (approx.). Nos 965
X009 Stoneware pipes, 100mm dia, over fume cupboards, supplying and fixing along
wall with iron brackets and plugs. m 2,013
Chain link fencing
X010 Supplying and fixing 50mm dia. heavy duty GI pipe uprights for receiving chain
link fence. Rate to include for painting one coat of anticorrosive and two coats of
enamel paint and welding 150mmx150mmx6mm thick MS plate to bottom of
pipe and fixing fiberglass pipe cap 50mm dia.(Rate exclude cement concrete
base & Excavation.) m 2,651
X011 Supplying and fixing 50mmx50mm gauge 10 , 1.5m high (gauge 10), galvanized
and PVC coated chain link fence . Fixed to existing GI post and including
horizontal bracing with 16mmx 6mm MS flat iron with GI J bolts and washers ,
PVC coated tieing wires etc., m2 1,734
X012 Supplying and welding 37.5mmx37.5mmx6mm MS angle iron horizontal bracing
to existing GI pipe posts. Rate to include for painting one coat of anticorrosive
paint and two coats of enamel paint. m 765
X013 Fabricating and fixing of MS grills with 25mmx 6mm flat iron frame and 6mm
dia.MS. rods welded to diamond shape 75mm centers both ways. m2 4,719
LANDSCAPING
Laying turf sods
X014 Supplying & laying turf sods of approved type including bedding material,
pegging and watering. m2 801
X-1 This BSR is for construction works only

Item Basic Rate

Code 2020
Road Construction
X015 Supplying and pilling approved 100mm aggregate for road construction, at site
excluding hire charges. m3 2,644
X019 Spreading ,watering & rolling 12mm aggregate including hire charges of
roller.(Materials Paid Separately) m3 3,044
X020 Spreading ,watering & rolling 50mm-20mm aggregate including hire charges of
roller.(Materials Paid Separately) m3 3,559
X021 Bitumen(80/100) surfacing first coat using 2Ltr/Sq.m including blinding with
sand at the rate of 125 Sq.m/Cu.m. m2 277
X022 Bitumen(80/100) surfacing 2 nd subsequent coat using 1 Ltr/Sq.m including
blinding at the rate of 125 Sq.m/Cu.m m2 185
X023 Emulsion /Cold bitumen (CRS-1) surface treatment 1st coat with 3.5 ltr/Sq.m
including blinding with sand,@125 Sq.m/Cu.m(Manual) m2 354
X024 Emulsion /Cold bitumen (CRS-1) surface treatment subsequent coat using 0.075
ltr/Sq.m including blinding with sand,@125 Sq.m/Cu.m(Manual) m2 125
The End
X-2 This BSR is for construction works only

BSR 2020 Construction

Uploaded by

Copyright:

Available Formats

BSR 2020 Construction

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BSR 2020 Construction

Uploaded by

Copyright:

Available Formats

Building Schedule of Rates

B.S.R. Workgroup Committee,

Contents Page Nos.

A.1 INTRODUCTORY NOTES A01-A03

B. PRICING PREAMBLES B01-B16

D. EXCAVATION & EARTHWORK D01-D02

F. CONCRETE WORK F01-F04

G. MASONRY WORK G01-G02

H. WATER PROFING H01-H01

J. STRUCTURAL METAL WORK J01-J01

K. METAL WORK K01-K05

L. WOOD WORK L01-L09

L1 CARPENTRY-STRUCTURAL TIMBER WORK-(ROOF) L01-L01

L2 JOINERY (WALLS) L01-L05

L3 IRON MONGERY L05-L09

N. PARTITION LINING / SUSPENDED CEILING N01-N06

P. ROOF COVERING P01-P03

Q. PLUMBING / SANITORY INSTALLATION Q01-Q16

R. MECHANICAL INSTALLATIONS R01-R06

S. ELECTRICAL INSTALLATION S01-S09

T. FINISHING & FLOORING T01-T05

V. PAINTING & DECORATING V01-V03

W. DRAINAGE SYSTEMS W01-W03

X. EXTERNAL WORK X01-X02

A. INTRODUCTORY NOTES & ADDITIONS TO SPECIFICATIONS

A.1 INTRODUCTORY NOTES

A.1.1 Trade Names ;

A.1.2 Based Standard

A.1.3 Analysis for Basic Rates

(e) Basic Cost

A-1 This BSR is for Construction works only

A.1.6 Allowances for lifting work

(b).Fourth floor and above

A-2 This BSR is for Construction works only

A.1.7 Earth work and landscaping

A-3 This BSR is for Construction works only

A.2 ADDITIONS TO SPECIFICATIONS

(Group-1): Door, Window and Fanlight Frames

Category A Satin Palu Milla Ketakala Tulang

(Group-2): Door , Window and Fanlight Sashes , Cupboards,

(Group-3): Roof Framework

Category B Domba Grandis

(Group-4): Ceiling Framework and Partitions

Category B Domba Grandis

(Group-5): Valance Board and Valley Boarding

(Group-7): Special Timber

Source: Selection of timber species- State Timber Coorporation.

A-4 This BSR is for Construction works only

A.2.2 Aluminium Panels

All Aluminium sections to be locally extruded

All Aluminium members shall be factory fabricated to the best standard of

Materials, method of fabrication, assembly, installation, fastenings, supports,

All joints in frames at corners, junctions and intersections shall be mechanically

Doors & Windows

The Contractor shall provide a guarantee in respect of the weatherproof properties

A-6 This BSR is for Construction works only

Partition members shall be 76mm in depth and the thickness of 1.2mm.

Locks- (Union or equivalent )

**Reffer notes 7.(d), Under pricing preambles

A-7 This BSR is for Construction works only