Power

GND
Adafruit Feather M0 Adalogger
Control
CircuitPython Name
https://www.adafruit.com/products/2796
GPIO
INT
DAC/AREF VBUS Connected to 5V USB port - absolute max 500mA
ADC
Touch VBAT The positive voltage from the JST battery jack
SERCOM
SERCOM Alt 3.3V 3.3V output from regulator - absolute max 400mA
Timer
Timer Alt

CHG
RESET #13

RST 3V ARf GND A0 A1 A2 A3 A4 A5 SCKMOSIMISO

Special 3.3V

RST
Max 3.3V AREF Optional LiPoly Battery
GND
Y0 AIN0 VOUT 2 PA02 A0 VBAT

BAT En USB 13 12 11~ 10~ 9~ 6 ~5 SCLSDA

TC4[0] S4.0 Y14 AIN2 8 PB08 A1 EN Connect to ground to disable 3.3V regulator.
TC4[1] S4.1 Y15 AIN3 9 PB09 A2 VBUS

adafruit!
TCC0[0] S0.0 Y2 AIN4 VREFB 4 PA04 A3 D13 PA17 1 S1.1 S3.1 TCC2[1] TCC0[7]

Feather M0
A4 D12

Adalogger
TCC0[1] S0.1 Y3 AIN5 5 PA05 PA19 3 S1.3 S3.3 TC3[1] TCC0[3] I2S/SD0

#8
TC6[0] S5.0 Y8 AIN10 2 PB02 A5 D11 PA16 0 S1.0 S3.0 TCC2[0] TCC0[6]
I2S/SCK1 TCC0[5] TC5[1] S4.3 11 PB11 SCK D10 PA18 2 S1.2 S3.2 TC3[0] TCC0[2]
I2S/MCK1 TCC0[4] TC5[0] S4.2 10 PB10 MOSI D9 PA07 7 AIN7 Y5 S0.3 TCC1[1] I2S/SD0
TCC0[6] TCC2[0] S4.0 S2.0 12 PA12 MISO D6 PA20 4 S5.2 S3.2 TC7[0] TCC0[6] I2S/SCK0
I2S/FS0 TCC0[3] TCC1[1] S2.3 S0.3 AIN19 11 PA11 D0 RX D5 PA15 15 S2.3 S4.3 TC3[1] TCC0[5]
D1 SCL

0
I2S/SCK0 TCC0[2] TCC1[0] S2.2 S0.2 AIN18 10 PA10 TX PA23 7 S3.1 S5.1 TC4[1] TCC0[5]
GND SDA

1 GND
PA22 6 S3.0 S5.0 TC4[0] TCC0[4]

D4 PA08 NMI AIN16 S0.0 S2.0 TCC0[0] TCC1[2] I2S/SD1

D7 PA21 5 S5.3 S3.3 TC7[1] TCC0[7] I2S/FS0
The Microchip (nee Atmel) SAMD21 is an D8 PA06 6 AIN6 Y4 S0.2 TCC1[0]
ARM Cortex-M0+ running at 48 MHz with
32kB on-chip SRAM, 256KB Flash memory
and built in USB. All GPIO is 3.3V
in/out max unless otherwise stated.
SERCOMs can be used as UART (TX on
SERCOM pad 0 or 2, RX on any pad), I2C
(SDA on pad 0, SCL on pad 1), or SPI
(SCK on pad 1 or 3, MOSI on pad 0 or 3 Absolute max per pin 10mA, 7mA recommended.
(SCK on pad 1) or pad 0 or 2 (SCK on pad
3), MISO on any pad remaining) Absolute max 130mA for entire package.