A S S E M B LY I N S T R U C T I O N S EN

Steel wall
swimming pool.
Manufacturas Gre, S.A. Aritz bidea nº 57
Belako industrialdea, apartado 69
48100 Munguia (Vizcaya) España

Before starting assembly, read carefully the instruction

nº reg. Ind. 48-06762
M A D E I N S PA I N

manuals of every components of the kit. Keep this

HIMPRN.21

instructions for future reference. Assembly videos on our

website. Non-contractual photos and pictures.
#1 03 - 04 #2 05 - 07

Safety Preparation
precautions. of the site.

#3 08 - 13 #4 14 - 23

Components. Installation.

#5 24 - 25 #6 26

Maintenance Accessories.
and use.

27

Guarantee.
Save this page for future claims
and / or returns
 safety precautions EN

#1
Safety
precautions.

OK

3,5 m
minimum

3
 assembly instructions

Safety
precautions.
Carefully read, understand, and follow all information in this Safety equipment
user manual before installing and using the swimming pool.
These warnings, instructions, and safety guidelines address → It is recommended to keep rescue equipment (e.g. a ring
some common risks of water recreation, but they cannot buoy) by the pool. WARNING
cover all risks and dangers in all cases. → Keep a working phone and a list of emergency phone Every electrical appliance fed in 220
Always use caution, common sense, and good judgment numbers near the pool.
V, has to be located at least at 3,50 m
when enjoying any water activity. Retain this information
from the edge of the pool.
for future use. Safe use of the pool
The equipment should be connected
Non Swimmers safety → Encourage all users especially children to learn how to to a voltage, with earth connection,
swim protected by a residual current
Continuous, active, and vigilant supervision of weak swim- → Learn Basic Life Support (Cardiopulmonary Resuscitation device (RCD) having a rated residual
mers and non-swimmers by a competent adult is required - CPR) and refresh this knowledge regularly.
operating current not exceeding 30
at all times (remembering that children under five are at the
mA.
highest risk of drowning). This can make a life-saving difference in the event of
→ Designate a competent adult to supervise the pool each an emergency.
time it is being used. Read the instructions carefully and
→ Weak swimmers or non-swimmers should wear personal → Instruct all pool users, including children, what to do in keep for future reference.
protection equipment when using the pool. case of an emergency
→ When the pool is not in use, or unsupervised, remove → Never dive into any shallow body of water. This can lead IF YOU HAVE ANY PROBLEM,
all toys from the swimming pool and its surrounding to to serious injury or death.
CONTACT US !
avoid attracting children to the pool. → Do not use the swimming pool when using alcohol or
medication that may impair your ability to safely use the www.grepool.com/en/after-sales
Safety devices pool.
→ When pool covers are used, remove them completely
→ It is recommended to install a barrier (and secure all from the water surface before entering the pool.
doors and windows, where applicable) to prevent unau- → Protect pool occupants from water related illnesses by
thorized access to the swimming pool. keeping the pool water treated and practicing good
→ Barriers, pool covers, pool alarms, or similar safety de- hygiene. Consult the water treatment guidelines in the
vices are helpful aids, but they are not substitutes for user’s manual.
continuous and competent adult supervision. → Store chemicals (e.g. water treatment, cleaning or disin-
fection products) out of the reach of children.
→ Signage is to be displayed in a prominent position within
2 m of the pool.
→ Removable ladders shall be placed on a horizontal sur-
face.

0º
OK

4
 preparation of the site EN

#2
Preparation
of the site.

3,5 m
minimum

Installation site Recommendations for choosing the best → Do not install under power lines.
Our pools are designed to be installed di- location for your pool → Protected from the wind and free from trees
rectly on the ground and for outdoor family since the pollen and leaves can make the
use. The ground must be firm, smooth, and → Choose a place where you will have to dig as pool water dirty.
perfectly flat. little as possible to level the ground. → A sunny area, where there is most sun in the
→ An area where in the event of rain, flooding morning.
Do not forget: 1000 l. = 1 m3 = 1000 Kgs. will not occur. → Near an electricity outlet, water outlet, and
→ Where there are no underground connec- drainage.
tions (water, gas, electricity, ...).

NEVER DO THE INSTALLATION ON: sloping, uneven, loose, or sandy ground with stones.

NO NO NO NO OK

5
 assembly instructions

2.1
Tool necessary (not included)

FLOUR

Mark the installation area:

Once the location area is chosen (which have
to be perfectly levelled), we’ll proceed at the
marking.

You ‘ve got 2 options for that :

→ 1 ° To prepare a concrete platform

(cement,…) with the necessary measure
according to your swimming-pool size.
→ 2° Directly on the ground : To mark the
ground using wood pickets, screwdriver,
funnel (or plastic bottle), flour or lime and
a rope.

PØ 2,40m = Ø3m PØ 3m = Ø3,50m PØ 3,5m = Ø4m

Ø3m Ø3,5m Ø4m

PØ 4,5m = Ø5m PØ 5,50m = Ø6m PØ 6,40m = Ø7m

Ø5m Ø6m Ø7m

6
 preparation of the site EN

2.2
Tool necessary (not included)

Levelling:
When levelling the ground, always remove
material from the top of the slope rather than
filling in the bottom: this will ensure greater
ground stability and firmness. Always remove
all grass, roots, stones, etc. Levelling is ex-
tremely important: devoting the necessary
time and effort to ensuring that your pool
sits properly on the ground will avoid prob-
lems later.

How to level: thanks to a large mason rule

(aluminium or wood) and a level, level out
the ground forming rectangles (or squares),
locating this rule in the selected and cleaned
area. When all the areas are on level and
when the excess of ground is removed, you
may fill in the small areas which are left to lev-
el out (with clean ground or sand) but always
compacting and levelling again afterwards. It
is very important the installation area is well
compressed and firm in order the ground
do not subside when the pool will be full
of water. Please ask a professional : builder,
gardener,…

2.3
Tool necessary (not included)

Finishing:
On the cleaned and levelled ground, spread a
light coat of sieved sand (max. 1cm).

Water and compact it (with a garden roller).

Check that is well levelled.

Do not use the sand to level the ground. The

finishing has to be perfect.

7
 assembly instructions

#3
Components.
Draw and clasify all components included In order to avoid any possible injury all
before assembly. swimming pool walking entrance must be
regulary checked.
It’s time to assemble the ladder and the
pump, follow the respective instructions.
Kits with missing parts will be covered by the
warranty only if reported to the after-sales
service within 15 days as from the date of
purchase of the swimming pool.

8
 components EN

Picture 1

EM

120cm

Picture 2

TPL & TP

132cm

Important.

Please, pay attention to the joint protectors coming with your pool when you take out and classify its components:

→ If your pool comes with EM joint protectors (see picture 1), you can find your pool parts list on pages 10 and 11.

→ If your pool comes with TPL&TP joint protectors (see picture 2), you can find your pool parts list on pages 12 and 13.

9
 assembly instructions

Components.

120 cm

Ø 6,40 Ø 5,50 Ø 4,60 Ø 3,50 Ø 3,00 Ø 2,40

m m m m m m

CH L LINER PCF
PVC PC-BAG CH 1 1 1 1 1 1

EM 14 12 10 10 8 8

LINER (L) 1 1 1 1 1 1

PCF 14 12 10 8 7 6

PI PIPC PV
PI 14 12 10 8 8 8
PC-BAG PC-BAG PLV

PIPC 14 12 10 8 8 8

14 12 10 8 8 8

PLAYA
PLY

PLAYA PLY TPVC

1400 mm 1400 mm 1400 mm 1330 mm 1145 mm 910 mm
( KITENV )

PU 28 24 20 16 16 16

PV 14 12 10 8 8 8

EM PU TPS T 140 120 100 80 80 80

( KITENV ) ( KITENV ) TAPÓN
PLUG
pag. 26 ( KITENV )
TPS 28 24 20 16 16 16

TPVC 1 1 1 1 1 1

T TT
( KITENV ) ( KITENV )
TT 28 28 28 28 28 28

Ø 6,40 m 5,50 m 4,60 m 3,50 m 3,00 m 2,40 m

m3
øm
h 1,05 m 1,05 m 1,05 m 1,05 m 1,05 m 1,05 m

h
m3 33,77 24,94 17,45 10,10 7,41 4,75

10
 components EN

Ø Ø Ø Ø Ø Ø
6,40 5,50 4,60 3,50 3,00 2,40
m m m m m m

2-3 2-3 2-3 2-3 2-3 2-3

EM
4h 3h 3h 2h 2h 2h

EM

TPS PLAYA
PLY

PU

PCF

SF

TPVC

TT

CH

PV

PI

PIPC PI
PU

11
 assembly instructions

Components.

132 cm

Ø 6,40 Ø 5,50 Ø 4,60 Ø 3,50 Ø 3,00 Ø 2,40

m m m m m m

CH L LINER PCF
PVC PC-BAG CH 1 1 1 1 1 1

LINER (L) 1 1 1 1 1 1

PCF 14 12 10 8 7 6

PI 14 12 10 8 8 8

PIPC 14 12 10 8 8 8

14 12 10 8 8 8

PI PIPC PV PLY
PLAYA
PC-BAG PC-BAG PLV
1400 mm 1400 mm 1400 mm 1330 mm 1145 mm 910 mm

PU 28 24 20 16 16 16

PV 14 12 10 8 8 8

T 140 120 100 80 80 80

PLAYA ZR TPVC PU
T1 14 12 10 8 8 8
( KITENV ) ( KITENV )

TPL 14 12 10 8 8 8

TP 14 12 10 8 8 8
TPL

TP EM 14 12 10 8 8 8

T T1 TT TPL & TP TPVC 1 1 1 1 1 1

( KITENV ) ( KITENV ) ( KITENV ) KIT-TPLTP
pag. 23
TT 32 32 32 32 32 32

Ø 6,40 m 5,50 m 4,60 m 3,50 m 3,00 m 2,40 m

m3
øm
h 1,17 m 1,17 m 1,17 m 1,17 m 1,17 m 1,17 m

h
m3 37,63 27,79 19,44 11,25 8,27 5,29

12
 components EN

Ø Ø Ø Ø Ø Ø
6,40 5,50 4,60 3,50 3,00 2,40
m m m m m m

2-3 2-3 2-3 2-3 2-3 2-3

TPL & TP
4h 3h 3h 2h 2h 2h

TPL
TT

PLAYA
PLAYA
PLY

PU
PU

PCF
PCF

SF
SF

TP
TPVC
TPVC

T
T TT
TT

T1
T1

LL

CH
CH

PV
PV

PIPI
PIPC
PI

TT
PU

13
 assembly instructions

#4
Installation.
4.1
BOTTOM SECTION PIECES (PI) FOR ROUND NOTE: (LO ) If the ground is not firm (concrete,
SWIMMING POOLS etc.), it is advisable to set a tile or slab into the PIPC PI
NOTE: These curved SECTION PIECES ARE FOR ground under each part PU to prevent the upright
THE BOTTOMS of ROUND SWIMMING POOLS. supports PV from sinking under the weight of the
Take each bottom section piece (PI) and fit a drop- water.
forged part (PU) in the middle (see photo A). Join
the section pieces to one another with the joining NOTE: Drop-forged parts PU under no circum-
pieces (PIPC), leaving a gap of about 1cm between stances shall be affixed to the ground by any
them (see photo B). Complete the circle with all means; in the event of doing so, you run the risk
the section pieces. Begin fitting the wallplate in of swimming pool breakage and the automatic
the middle of a drop-forged part (PU) previously loss of the warranty.
positioned half way along each section piece. If
on completing the wallplate installation the circle * Use duct tape to cover parts PU and PIPC on
made by the section pieces is too small, open out the inside of the pool and thus avoid that may
the section pieces until you achieve the exact di- damage theliner.
ameter. If, on the other hand, the circle of section
pieces is too big, you will have to close them up un- * Place the top rails (PLY) to estimate the distan-
til the circle matches the diameter of the wallplate. ce between (PU) pieces.

PI

PU LO

PIPC

1cm
PI PU PI PI

PIPC
PI PIPC

Picture A Picture B Picture C

14
 installation EN

4.2
* IMPORTANT! BEFORE ASSEMBLY, DEBURRING, Start to place the sheet at the middle of a pressed part
USING A FILE AND SANDPAPER, THE EDGE OF (PU) previously situated at the middle of each profile,
THE CLOSING WALL (CH). (see page 14). If when closing the sheet circle of the
profiles it is small, all the profiles must be separated
NOTE: REFERENCES: K300WET AND K350WET DO from each other until obtaining the exact diameter. On
NIT HAVE PUNCH HOLES IN THE METAL SHEET the other hand it is too bog, the profiles should be
(CH) OF THE POOL. moved closer to each other until equaling the circle
with the diameter of the sheet.
Fit the wall plating CH vertically on a piece of cardboard
(to avoid damaging the area prepared for the installa- Complete the circle and close the plating CH thanks
tion). Make sure the square and pierced piece is always to the screws TT. The screwhead has to stay in the TT
located in the superior part and face to dominating interior part of the pool, the ring and the blind nut
winds. Fit the plating extremity and the first profile (PI) in the exterior part (Tighten the screws without dis-
together and make the plating extremity correspond torting the material).
with the top of the joining-piece PU. Now, you can un-
fold it introducing it in the profiles PI, working clockwise.

CH

PI

PU

4.3
PVC PROTECTIVE STRIP (INTERIOR POOL COV- The Ground Cover or floor tapestry - Caution: Clean adjusting and cutting away excess from the total sur-
ERING): all dirt from the pool wall and bottom with a vacuum face area. Cut so that the bottom section pieces and
cleaner before placing the ground cover or floor tap- the metal parts are covered. This way the liner will be
Attach the PVC strip to the top nut at the joint of the estry in position. protected when you install it.
wall plate so that it hangs down inside the pool to Fit the protective ground cover or floor tapestry in the
cover the screw heads. interior of the pool and smooth out all the creases,

MPR TPR

TPVCP

TPVCP

15
 assembly instructions

4.4
ASSEMBLY OF THE PVC LINER: NOTE: Temperature too low: hard and rigid liner; perimeter of pool bottom avoiding any folds. It
EXTENDING THE LINER: later, too small. Temperature too high: flexible is very important that the liner is well centered
and elastic liner; later, too big. Pull and extend and extended.
Important: The liner used in the manufacturing of the liner (L) in the shade to recover its texture,
all our pools, is developed for exposition to heat at least 2 hours before installing it. Ideal tempe- NOTE: If there any folds in the bottom of the liner,
and ultraviolet rays during long periods. Therefore, rature: To manipulate the liner better, try to do this is no reason for it to be changed because it is
under certain weather and usage conditions, the li- this at an outside temperature between 20 - 25º NOT a factory defect.
ner qualities can slightly vary. The interior liner of the C. Situate the liner (L) at the center of the pool.
pool is manufactured from flexible PVC (thermoplas- Extend it at the bottom and fitted against the SERIAL No: Locate it on the bottom or wall of the
tic). Its properties allow optima installation condi- side towards the steel sheet. The welding that liner and write the serial No. in the box on the ins-
tions when the outside temperature is between 20 joins the bottom with the side must be perfect- truction sheet for possible claims.
ºC and 25 ºC. ly fitted against the lower profiles of the entire

LINER

ºC

20º - 25º

SERIAL NO.
Examples
FP R 301 20233651
FP R 451 H Y201907
SP 385F GP 201901

SERIAL NO.;

16
 installation EN

4.5
ATACHING THE LINER:

Locate the welded seam of the wall (W), which can be served in the liner wall on completing this operation
used as a guide for fitting the pool liner. Starting from evenly around the pool to prevent wrinkles. If the liner
that point, hang the top edge of the liner over the wall wall is too short, stretch it evenly all around the pe-
plating so that the weld (W) is perfectly straight and rimeter.
perpendicular to the ground. as you hang the liner,
hold it in place provisionally with clothes pegs. Ensure
there is a uniform overlap. Distribute any excess ob-

L CH

LINER

17
 assembly instructions

4.6

PCF

PCF

L
FLEXIBLE TOP SECTION PIECES (PCF) for Round
Swimming Pools

NOTE: These FLEXIBLE SECTION PIECES ARE FOR

THE TOPS of ROUND SWIMMING POOLS.
CH
They are fitted on top of the liner once this has been
fitted over the pool wallplate and do not need to be
joined together. They are positioned one after the oth-
er, and when the perimeter is completed, the extra
length is cut off.

Place each PU piece over the top section pieces;

they must be lined up with those located in the
lower part.

PCF
PU

CH

PU

18
 installation EN

4.7
F I T T I N G A N D AT TA C H I N G T H E U P R I G H T to the top joining piece. Next, fit the rest of the screws
SUPPORTS (PV) TO THE WALL PLATING: T (3 + 3 per support). Proceed in this way until all the
upright supports are attached at top and bottom.
With reference to the plating closure, place the first Take one PLY to calculate the distance between the
superior and inferior joining-pieces PU in that point (To pressed profiles PU.
plug all closure screws TT). Use a trim piece to calculate
the distance between the joining pieces PU. Attach an NOTE: Upright supports should be perfectly vertical
upright support (PV) to the first bottom joining piece all around the pool (take the wall plate ribbing as a
by the central screw T. Then attach it in the same way reference.

PCF PU

T *

TT

1ª PU

PV

19
 assembly instructions

4.8
INSTALLATION OF THE UPPER PROFILES (PLY): finger tightening the (and not fully tightening them Put the plastic plugs TPS (only for pools of 120 cm)
so there is some play among them) the inside screws on the screws (for protection) at the outside of the
Avoid that the PLY pieces fall into the pool duringinsta- of each side (1º). After having placed all the PLYs, pool.
llation because they can damage the liner. Place each re-check that the vertical profiles are upright, if not,
PLY supported by two consecutive PUs with round part correct their position. Then continue positioning the ATTENTION: getting on, walking on, or sitting on the
outside. You will see that each PLY has four holes (two outside screws (2º) and tighten all the screws to the PLYs is firmly prohibited, as well as jumping or diving
inside and two outside) for fixing to the joint pieces. structure. from the same.
Start by fixing each PLY to the joint pieces but only

PLY
PLAYA 2º 1º T PLAYA
PLY

2º

PU

PCF

PV TPS

4.9

EM

* IMPORTANT! BEFORE ASSEMBLY, DE-

BURRING, USING A FILE AND SANDPA-
PER, THE ENDS OF EACH PLY.

PLACING THE FLEXIBLE JOINT PROTEC-

TORS EM: (only for 120 cm pools):
2º 1º
The flexible joint protectors are fitted to the
joints between the trim pieces. To fix them,
start by fixing the back part (inside the pool)
to the trim piece and with the aid of a screw-
driver lever the front ribs over
until they fit to the trim piece.

PV

20
 installation EN

4.10
JOINT PROTECTORS: TPL and TP. fixed to the back side of the 2 strim pieces. Then, it
(Only for 132 cm pools) has to be tightened to the front side of the pool, fixing
the TPL verge to the PU1 hole. Now, fix TP to TPL T1
These pieces are to be fitted joining and protecting by the lower side using a screw T1 to join them. This
the trim pieces. Joint protectors are made up of 2 ele- process is to be repeated for all the joint protectors.
ments: Strim Piece protector (TPL) and Vertical Section ATTENTION: For the straight area, the TP notch must
protector (TP). First, the back side of TPL has to be be removed so the part fits into the PV2.

TPL

TPL

TPL

TP
TPL

T1

TP

PV

21
 assembly instructions

4.11
FITTING THE RETURN VALVE (V): is clean before filling the pool). Mark the position of Fit the other seal (J) and the other friction ring (F)
(IMPELLER NOZZLE: V) the hole on the liner with a felt pen and make a cross- and tighten firmly with the nut (T). Insert the return
This valve is located at the bottom of the pool wall, shaped cut in the centre of the mark with a stanley hose (M) which goes from the outlet of the treatment
and water is returned to the pool through it after knife or similar. Do not cut beyond the edge of the unit to the return valve (V), and secure it with the
treatment in the treatment unit. Start pouring water hole. Place inside the pool through the cut, with a clamp (A).
into the pool through a garden hose, and stop 4 cm seal (J) and a friction ring (F). Cut the protruding part
below the bottom of the valve hole (check the liner of the liner.

F CH L F
J F R

TEFLON

T R

4 cm

A
4 cm
M

WATER WATER

4.12
ATTACHING THE SKIMMER BODY (S) TO THE wall plate and liner are within the groove (X) made tightly to the skimmer, connect one end of the hose
OUTSIDE OF THE POOL: for this purpose and fit the two shorter screws into to the skimmer connecting bushing (C) using a clamp
the larger centre holes from the inside of the pool (A), and fit the other end to the treatment unit inlet.
Fill the pool with water until the level is 4 cm from the through the double seal and the liner. Screw them Clamp this end also.
bottom of the perforation for the skimmer. Using a into the center holes on the skimmer (S). Cover the
Stanley knife, cut the liner (L) inside the pool opposite connecting bushing (C) and the water treatment unit NB.- Fit Teflon on all water hose connection threads
the perforation. Locate the double seal (J) so that the inlet with Teflon. Screw the connecting bushing (C) to ensure leak-tightness.

S CH L

A +

*
4 cm
L

X J

22
 installation EN

4.13
FITTING THE SKIMMER FINISH FILLING THE POOL UP
FRAME (M): TO HALFWAY UP THE SIMMER TS
DOOR, (10-15 cm below the pool
En sure that all holes are lined up edge) SO WATER ENTERS INTO
properly (seal to wall plate per- IT AND FILLS THE FILTERING S
foration to skimmer). Screw 10 SYSTEM.
remaining screws loosely through 15 cm
the frame to check that the fit is
correct. Then tighten the screws
a little more one by one in the
4 cm
order indicated. Finally, tighten J
them fully in the same order.

LAST DETAILS: Pressure fit the

1º 10º 3º
trim part of the skimmer frame K
(Z). To finish, introduce the flap
(K) through the rectangular gap
(delicately press the two ends 8º 5º
and fit the protrusions). Place the M
6º 7º
basket (O) into the skimmer and
the skimmer body cover (TS).

4º 9º 2º Z

K
TS

TA

WATER

S
Z

J
C

JOINT
FILTER INLET PIPE

GRILLE

M
SHEET

FILTER INLET PIPE

LINER PVC

23
 assembly instructions

#5
Maintenance
and use.

Ok
D

→ The pool water level must always be at → The use of a pool kit involves respecting sa-
least 15 cm from the edge of the upper fety instructions defined in the maintenance
edge of the same. and usage guide.
→ During the season for use of a pool kit, use → Never leave a pool kit for installation of the RESPECT THE ENVIRONMENT DO
the filtering system once a day to assure ground outside and empty. NOT TAKE APART THE POOL UN-
complete recycling of all the water and → Regularly clean the PVC liner and the wa- LESS IT IS STRICTLY NECESSARY.
always when the pool is not used for ba- ter level line with non-abrasive products. IF YOU DO SO, PLEASE REUSE
thing (see purifier manual). Periodically clean the bottom fold layer at THE WATER. WATER IS A SCARCE
→ During the season for using the pool, re- the joint with the side liner because dirt GOOD.
gularly verify the obstruction level of the can collect at this point. If you accidentally
filtering means. make a small hole in the liner, it can be When your pool reaches the end of
→ Revise all the screws of the pool, and the repaired with AR202 or V12 patches. its useful life, it should be disassem-
possible corrosion points as much as pos- → The summer covers (isothermal) protect bled; the different materials (plastic
sible. your pool from insects, dust, leaves, etc. and steel) should be separated and
→ Never completely empty the pool. There is and prevent loss of water temperature. taken to the disposal point indicated
a risk of seriously damaging the pool struc- Always place it with the bubbles in contact by local authorities.
ture if there is not sufficient water level. with the water.
→ Not respecting the maintenance instruc-
tions can cause serious health risks, espe-
cially for children.

24
 maintenance and use EN

WINTER-SEASON: CHEMICAL MEASURES:

Please read carefully the chemical product manufacturer instructions. WARNING:
A) If you choose not to dismount the pool: Keep chemical products in a clean, dry and out of children place. Important:

1- Clean the liner bottom and sides with a non-abrasive product. Every products used have to be compatible with the P.V.C liner.
2- Treat the water with a chemical product for wintering. We recommend using LIQ-
UID WINTERISER instead of floats with solid product to avoid discolouring the liner. →F
 irst filling: Analyse the water pH and chlorine (Cl) and adjust them to the optimal
3- Leave the pool full of water considering: levels: pH: 7,2 – 7,6; Chlorine: 0.5 – 2 ppm.
a) For pools with skimmer and refulling pipe, reduce the water level 5 cm underneath →C
 hlorine treatments: Consist in increasing the chlorine level until approximatively
the skimmer and close the refulling pipe with the screw tap which is included 20 ppm to eliminate germs and seaweeds. This process has to be done only when
with the filter. the pool water comes from rivers or ponds, … or if it stayed a long time without
b) For pools with exhaustion and refulling pipes, reduce the water level 20 cm from any treatments.
the superior edge of the pool and close the pipes using the screw system incorpo- →C
 hecking: Check at least once a week the chlorine levels (use a chlorine and
rated. pH analyser). In the same way, we advise to add an algicid to prevent seaweeds
4- Disconnect the pipes. Do not dismount the skimmer and the refulling and ex- appearance.
haustion pipes.
5- Protect the pool with a winter cover, and put a floating element between the cover Never have a swim before the chlorine level stabilization. Do always use a floating
and the water, in order to protect it from frost. dispenser for the chemical product (tablets) dissolution. The chemical product mea-
6- Filter: disconnect it from the pool. Clean it, empty the sand or remove the car- suring out has to be done in accordance with: Your pool water volume, the bathe
tridge, dry it and keep it in a covered and sheltered from dampness place. frequency, the climatic conditions, the water temperature and the location. Do always
7- Accessories: remove every accessories (ladder, alarm, spotlight, pole…), rinse move the water and wait for the chemical product dissolution before adding another
them with soft water and tidy them away. one. Wait approximatively 12 hours between any pH, chlorine or algicid adjustment
TO RUN THE POOL AGAIN: Remove the winter cover, install the filter, change at using the filter system.
least 1/3 of water and realize a chlorine treatment. Switch on the filter for at least 8
hours in an uninterrupted way, respecting the continuous working period indicated MECHANICAL MEASURES:
in the filter manuals.
Check the filter, the skimmer, the valves and the pipes are well connected to the
B) If you choose to dismount the pool: pool. Do consider high water temperature will involved more time for the filtering.
Theoretic filtering time = Water volume / Filter system discharge (generally 8h/day
1- Empty the pool. Measures: Filter, Automatic pump for handling clean water or with water temperature of 21°C), (Ideal: 2h in the morning – 4h around midday – 2h
communicating vessels system. Communicating vessels system: Use the hose from in the afternoon). PLEASE RESPECT THE CONTINUOUS WORKING PERIOD INDI-
your filter with the smallest cross-section. Fix a weight to one of its end and plunge CATED IN THE FILTER MANUALS.
it into the swimming pool. After this, sink the whole hose, until there is no air inside.
With one hand, and under the water stop up hermetically the end of the hose and VACUUM CLEANER (MANUAL OR AUTOMATIC):
take it to the emptying point. Remove hand, and water will start running. Do not use
this water for watering the plants, because it contains chemical products. Only for pools with skimmer. Connect an hose extremity to the brush head and
2- Clean every pool constituents with a sponge and a soap product with a neutral immerse it into the water to make it fill in. Connect the other pipe extremity to the
pH. Dry them and tidy them away in a dry and clean place. exhaustion adapter (TA) and place it above the skimmer basket. Switch on the filter
That’s normal that after having installed and dismounted the pool several times, the in the FILTER position and begin to clean the bottom. Pay special attention to areas
P.V.C liner dilate and loose its elasticity. with folds where dirt accumulates.

TO RUN THE POOL AGAIN: Read another time this manual instructions from the BOTTOM CLEANER VENTURY STYLE:
beginning.
Connect a garden hose to the bottom cleaner join and introduce it into the pool.
Open the tap until a normal pressure to make the water flow out against the bottom
of the pool, producing in that way an ascendant stream which leave the dirt into the
filter (bag) which is adjust on the bottom cleaner.

PROBLEM CAUSE SOLUTION

Perform a return was of the filter.

Bad filtration. High PH. Organic residues in
Muddy water Add PURIFIER in tablets using a dispenser.
excess
Perform a shock chlorinating.
Gently clean the bottom and walls of the pool.
Green water Seaweed or mud formation Analyse the pH and adjust it to between 7.2 - 7.6.
Add algicide and liquid purifier.

Analyse the pH and adjust it to between 7.2 - 7.6.

Brown water Presence of iron or manganese
Perform a shock chlorinating. Add liquid purifier.

Analyse the pH and adjust it to between 7.2 - 7.6.

Incustrations Presence of Calcareous in the water
Add anti-calcareous once a week.

Eyes and skin Analyse the pH and adjust it to between 7.2 - 7.6.
Misadjusted PH. Organic residues in excess
irritations. Bad smell. Perform a shock chlorinating.

EMPTYING - COMMUNICATING
VESSELS SYSTEM

25
 assembly instructions

#6
Accessories.

CLEANERS HEAT PUMPS HEATING SYSTEMS

WATER TREATMENT FLOOR TAPESTRY ISOTHERMIC COVERS

WINTER COVERS COVER ROLLER FOR ABOVE SOLAR SHOWERS

IMPORTANT: you can view the entire range of products on our site: www.grepool.com

26
 guarantee EN

U
AR
ANT

Guarantee card
E
G

E
Keep your manual with the purchase justication (payment receipt)

S
Y
E R
A
for any type of reclamation.

Any reclamation against guarantee should be made by an online dec- Likewise, all plastic parts are excluded from the additional commercial
laration, via the www.service-gre.com website, together with receipt guarantee, that is to say:
of purchase. You may be asked for photographs to justify the claim. → The liner
No returns of material will be accepted without previous agreement. → Any decorative part
The client will support all costs of all returns of goods, (packaging and
transport). To be able to benet from the guarantee, your pool should include this
document.
AFTER VERIFICATION AND CONFIRMATION OF A MANUFACTUR- Guarantee valid for pools sold after 1 January 2016.
ING DEFECT
→ Liner: 2 years for the seams and water tightness in normal conditions
→ The products that eectively show defects will be repaired or will be of use. The guarantee does not include: Ripping, tears, breakages,
replaced free of transport costs. stains ( caused by pouring treatment products directly into the wa-
ter ), stains linked to the growth of algae, stains related to the de-
The guarantee is limited to the repair or replacement of the defective composition of foreign bodies in contact with the liner, stains and
part. It does not include, under any circumstance, the payment of com- decolouring resulting from the action of oxidising products, colour
pensation for harm and damages. maintenance and wear due to friction of the material over diverse
surfaces. Deformation of the liner that has been left without water
THE GUARANTEE IS NOT APPLICABLE IN THE FOLLOWING SIT- for 24 hours (never completely empty the pool). You should keep the
UATIONS: label with the serial number of the liner that is on the product and on
its packaging. This number and a sample of the liner will be required
→ Use of materials that do not comply to our instructions. for any eventual reclamation against the guarantee.
→ Damages caused by mishandling or an installation not complying
with the instructions. → Filter group: The pump has 2 years guarantee (electrical problem ),
→ The maintenance instructions were not followed. in normal conditions of use. The guarantee does not cover breakage
→ Inappropriate or wrong use of the chemical product. of parts (pump base/sand deposit, pre-lter cover, multi-directional
trap...), wear due to a poor connection, use of the pump without wa-
ter, wear due to abrasion or corrosion ( the lter group should be locat-
ed in a cool and dry position, kept protected from water splashing ).
IMPORTANT:
→ Other components: 2 years.
Manufacturas Gre interchanges components in exchange
for others to be veried. If, after the verication no anomaly
THE FOLLOWING IS NOT INCLUDED IN THE GUARANTEE:
or dysfunction is detected, Manufacturas Gré reserves the
right to invoice the client for the cost for transport and
→ Cuts in the liner
other diverse expenses.
→ The assembly and lter connection
→ The assembly
→ The lling with water
→ Installation of the edges
DURATION OF THE GUARANTEE: → The wintering
→ Maintenance
Gre pools are subject to the legal 2- years guarantee established by
the General Consumers and Users Defence Act counting from the date AFTER SALES SERVICE WITHOUT GUARANTEE:
of purchase and according to the terms of the same. We remind you
that for the guarantee to be applicable the purchase receipt should be The guarantee is valid in all the UE countries, UK and Switzerland.
presented and/or the return of the product. Manufacturas Gre also grant GRE oers the buyer -in addition to the rights of guarantee from the
an additional 2-year commercial guarantee for this pool model, that is seller that correspond by law and without limiting them- an additional
to say making a total of 4 years, exclusively regarding the metallic parts right according to the conditions of the following obligations guaran-
of the pool structure. This additional commercial guarantee will not aect teed for new products.
the rights of the consumer according to the legal guarantee.

The following is excluded from both guarantees:

→ The PVC Liner, in the case of disassembly and re-assembly of the pool
→ Stains or decolouring that can appear in the liner due to its use
→ Damages to the pool derived from poor ground preparation where
the pool is located

4
→ Damage to the pool derived from burial of the same
AÑOS
→ Any damage to the pool derived from misuse of the same, according
→ In the case of problems, contact us: ANS
to the instruction manual YEARS
www.grepool.com/en/after-sales

GARANTÍA
en estructura metálica

GARANTIE
sur la structure acier

WARRANTY
on the metallic structure

27
 MANUFACTURAS GRE S.A.

Aritz Bidea, 57 BELAKO INDUSTRIALDEA,

APARTADO 69, 48.100 - MUNGUIA (VIZCAYA) ESPAÑA.
Telf.: (34) 94 674 11 16 · Fax: (34) 94 674 17 08

e-mail: [email protected]
www.grepool.com

GUAR AN TE E N º

We reserve the right to change all or part of the articles or contents of this document,
without prior notice

30.11.20