SPARE

PARTS NOTICE

Wärtsilä 2-stroke RT-181

Technical Services Issue 1, 17.06. 2015

Plunger diameter for Fuel pump

At your convenience
V4-82
Information to all Owners and Operators of Concerned component
Wärtsilä RT-flex82C, RT-flex82T and W-X82 engines. Fuel pump unit, fuel pump (FOP) plunger
of all RT-flex82C, RT-flex82T and W-X82
engines.

Current situation
The fuel pump plunger diameters of early
RT-flex82C and RT-flex82T engines were
designed with a high supply margin. In the
meantime a new specification has been
released for new engines.

Recommendation
Decreasing the plunger diameter of the
fuel pumps to the defined diameter in
accordance with the latest Wärtsilä
specification for all engines with previous
specification is recommended.

Note
Insert this Spare Parts Notice in section
5556-1/A1of your Spare Parts Catalogue
on board and in the offices.

Wärtsilä Services Switzerland Ltd. Tel (24h): +41 52 262 80 10

PO Box 414
CH-8401 Winterthur [email protected]
 SPARE PARTS NOTICE

RT-181, Issue 1, Page 2 / 4

Contents
Page
1 Introduction 2
2 Diameter specification – Fuel pump plunger 2
3 Ordering fuel pump with new specified plunger diameter 3
4 Contacts 4

1 Introduction

This spare parts notice informs you that Wärtsilä has introduced a new plunger
diameter specification for RT-flex82C and RT-flex82T engines. The specification for the
W-X82 engines is already applied from the beginning.

The capacity of a fuel pump depends on the plunger diameter. The fuel pump plunger
diameters of early RT-flex82C and RT-flex82T engines were designed with a very high
delivery margin, compared to the required flow for engine operation. Recalculation by
Wärtsilä confirmed that the plunger diameters can be decreased on these engines.

With the smaller plunger diameter a more even load distribution is achieved on the
supply unit components especially at low engine load operation. This change does not
have any other influence on engine performance.

All new engines produced since the introduction of the new specification are equipped
with the smaller plunger diameter. Service experience confirmed the validity of the new
specification.

2 Diameter specification – Fuel pump plunger

2
3

1. Fuel pump cylinder 3. Plunger diameter Ø in mm

2. Fuel pump plunger
Figure 1: Fuel pump cylinder and plunger
 SPARE PARTS NOTICE

RT-181, Issue 1, Page 3 / 4

The new specified plunger diameters are recommended from now on for all
RT-flex82C, RT-flex82T and X82 engines:

Table 1: Plunger diameter specifications

Current
New plunger
Number of Number of plunger
Engine type diameter
cylinders fuel pumps diameter
(mm)
(mm)
82C 6 4 42 40
7 4 46 40
8 4 46 42
9 6 42 40
10 6 46 40
11 6 46 42
12 6 46 42
82T 6 4 42 40
7 4 46 40
8 4 46 42
9 6 42 40
X82 6 4 - 40
7 4 - 44
8 4 - 46
9 6 - 40

3 Ordering fuel pump with new specified plunger diameter

When you order the applicable fuel pump, also mention the related new plunger
diameter (refer to Table 1).

ATTENTION:
Wärtsilä recommends using the same plunger diameter on all fuel pumps in the fuel
pump unit.
Existing spare parts (fuel pump, fuel pump plunger) on board can be used up.

During a transition period, it is possible to operate the engine with different plunger
diameters until all fuel pumps are exchanged or had overhauls. This is confirmed by
service experience on several engine types.

Table 2: Fuel pumps – Spare part numbers

Spare part number – Fuel Spare part number - Fuel pump

Engine type
pump plunger complete
RT-flex82C LF 55600 LF 55500
RT-flex82T VF 55600 VF 55500
W-X82 CX 55600 CX 55500
 SPARE PARTS NOTICE

RT-181, Issue 1, Page 4 / 4

4 Contacts
4.1 How to contact Wärtsilä
For questions about the content of this Spare Parts Notice, or if you need Wärtsilä
assistance, services, spare parts and/or tools, please contact your nearest Wärtsilä
representative.
If you do not have the contact details at hand, please follow the link “Contact us” – “24h
Services” on the Wärtsilä webpage:
www.wartsila.com

4.2 Contact details for emergency issues

4.2.1 Operational support
For questions concerning operational issues, please send your enquiry to:
[email protected]
or phone 24hrs support: +41 52 262 80 10.

4.2.2 Field service

If you need Wärtsilä Field Service, please send your enquiry to:
[email protected]
or phone 24hrs support: +41 79 255 68 80.

4.2.3 Spare parts

If you need Wärtsilä spare parts and/or tools, please contact your nearest Wärtsilä
representative or your key account manager.

© 2015 Wärtsilä Services Switzerland Ltd. – All rights reserved

No part of this publication may be reproduced or copied in any form or by any means (electronic, mechanical, graphic, photocopying,
recording, taping or other information retrieval systems) without the prior written permission of the copyright holder. Wärtsilä Services
Switzerland Ltd. makes no representation, warranty (express or implied) in this publication and assumes no responsibility for the
correctness, errors or omissions for information contained herein. Information in this publication is subject to change without notice.

Unless otherwise expressly set forth, no recommendation contained in this document or any of its appendices is to be construed as
provided due to a defect of the product, but merely as an improvement of the product and/or the maintenance procedures relating thereto.
Any actions by the owner/operator as a result of the recommendations are not covered under any warranty provided by Wärtsilä and such
actions will thus be at the owners/operators own cost and expense.

NO LIABILITY WHETHER DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL, IS ASSUMED WITH RESPECT TO
THE INFORMATION CONTAINED HEREIN. THIS PUBLICATION IS CONFIDENTIAL AND INTENDED FOR INFORMATION
PURPOSES ONLY.