Skip to content

Manuals+

User Manuals Simplified.

Concox WeTrack2 General Vehicle GPS Tracker User Manual

Home » Concox » Concox WeTrack2 General Vehicle GPS Tracker User Manual

Concox WeTrack2 General Vehicle GPS Tracker User Manual

Contents [ hide
1 Introducing Your
Device
2 Inside the Box
3 Overview
4 Specifications
5 Getting Started
6 Operation of device
7 Platform
8 Troubleshooting
9 File Downloads
10 Related Manuals

Introducing Your Device

Learn about your device’s layout, indications and specifications.

Inside the Box

Check your product box for the following items:

Device
Charging cab
Relay
Relay socket
User manual

Overview

LED Indications

Power indicator (red) Indication

Quick Flashing (flash 0 3s at
Low battery
interval of 0.3s)
Solid red Charging
Flashing (flash 1s at interval of 3s) Full Charge
OFF Power off or low battery
Slow flashing (flash 0’1
Working normally
at interval of 3s)

GPS indicator (blue) Indication

Flashing (ON:0.3S, OFF:0.3S) Searching GPS signal

Slow flashing (flash 0 1s at interval

Receive GPS signal normally
of 3s)

OFF No GPS signal

GSM indicator (green) Indication

Quick Flashing (flash 0.3s at interval of

GSM initializing
0.3s)

Flashing (flash 1s at interval of 3s) Receive GSM signal normally

Solid green In communication with phones

OFF No GSM signal or no SIM card

Slow flashing (flash 0 1 at interval of 3s) GPRS on line

Specifications

Dimension 78.0(L) x 41.0(W) x 13.0(H) mm

Weight 38g

Working voltage 9-90V

BaCkup Battery 270mAh / 3.7V

Operation Temperature -20°C – 70°C

Humidity 20% – 80%

Standby Time 60 hours

GSM Frequencies 850/900/1800/1900 MHz

GPRS Class 12, TCP/IP

GPS Channel 32

GPS Sensitivity -162dBm

Acquisition Sensitivity -148dBm

Position Accuracy < 10m

TTFF (Open Sky) Cold Start: < 35s

Hot Start: < 1s

GSM/GPS Antenna Built-in design

LED Indicator GSM-green, GPS-blue, Power-red

Data Transmit TCP, SMS

Alarm when get in or get out a

Geo-fence Alarm
specified area

Report when speeds hipher than

Speeding Alarm
the pre-set value.

Alarm when backup battery is

Low Power Alarm
running out

Non-movement Detection Movement alarm based on built-in 3D motion sensor

Mileage Report Track by time/distance interval

Remote Control Cut off petrol/electricity

Getting Started

Switch on

Get started by assembling and setting up your device for its first use.

1. Open the SIM card

 2. Insert the SIM

NOTE:
SIM card should be equipped with GPRS and SMS functions.
3. Turn the battery switch to ON.

4. Close the SIM card cover and connect the device with the external power line which will be used to charge the terminal and
built-in battery.

Switch off

1. Toggle the battery switch to OFF.

Charge the device

Plug the device connector into a charging cable.

The charging cable with 1A FUSE for short-circuit over current protection.
NOTE:

Improperly connecting the charging cable can cause serious damage to the device. Any damages by misuse are not covered by the
warranty

Install the device

You need to choose somewhere that it won’t be found.

1. Your device has built-in GSM antenna and GPS antenna. During installation, please make sure the receiving side face is up ;
any high power devices such as reversing radar, anti-theft device or communication equipment would affect the signal of the
device.
2. All metallic cases of the windshield will attenuate the signal on the tracking device. It’s simply due to the shielding effects of the
metal compound of the case.
3. The device should be fixed into position with cable ties or wide double-side tape.

Installation please refers to below picture.

 Under the dash board below the front windshield;
In the parcel shelf in the rear;
In the front bumper (non-material face), make sure the device does not get wet;
Under the wiper version (non-metal), make sure the device does not get wet;
Non Covert Installation – fix the device on the dash board below

Dev1ce Wiring

1. Since the recharging voltage can be much higher than the working voltage, for your safety, please use with vehicle battery
voltage no more than 72V. The red wire is the positive, the black wire is the negative.
2. Connect the black wire to ground.

Device wiring d1agram

NOTE:
Please pay attention to the diagram description, battery is no more than 72V and relay remains 12V/ 24V

Power/ACC/Tele-cutoff(petrol/electricity) control line (4 pin)

1. Your device comes with a power cord and is designed to use only manufacturer-specified original device. The red line is
positive while the black one is negative (the side should not be connected with ground wire).
2. The ACC line (orange) connects to ACC switch of the Please be sure to connect the ACC line; otherwise the device won’t
enter ignition detection status when disconnect the ACC line. If you don’t need to anti-theft temporarily, just connect the ACC
line to the positive side in parallel.
3. Tele-cutoff(petrol/ electricity) control line (yellow) is connected to pin 86 of the Tele-cutoff (petrol/ electricity) relay (equal to the
yellow line of the relay socket).

Quick Operation Instructions

To properly use the device, common parameters should be set before initial use. This can be done by using the parameter editor or
by sending SMS commands to the device. (“,”should be English comma and no space before and after the comma)

Add SOS number

SMS command to the device to add the SOS number.

SOS,A,No.1,No.2,No.3#

“A” means to add new numbers, for example:

SOS,A,18165542975,18165542976,18165542977#

It will reply

“OK! SOS1: 18165542975 SOS2: 18165542976 SOS3:

18165542977″ after set successfully.

APN setting

To ensure GPRS is activated, please make sure APN is correct. You can send SMS command to set APN: APN command format
APN,APN’s Name# E.g: APN,internet# ( “internet” is the APN of carrier) The device will reply “OK” if setting successfully. Note: The
APN of some countries have user name and password, you may need to send SMS command as following: APN,APN name, user
name ,password#

Server setting

Default platform is www.tracksoIid.com

To connect to other platform, please send the SMS command to change the DNS or server IP: DNS : SERVER,1,DNS,Port,0# E.g:
SERVER,1,gpsdev.tracksoIid.com,21 1 00,0# IP: SERVER,0,IP,Port,0# It will reply “OK” after set successfully.

Set the center number

If you want to cut off/restore oil by SMS command, you have to set a center number firstly. Only the center number can send the cut
off/restore oil command to the device. You can set your own mobile number as center number. The command for setting center
number is: CENTER,A,mobile number# E.g. CENTER,A,18165542976# If set successfully, there is an “OK” reply message.

NOTE:
Only the SOS number can be used to add or delete center number successfully. There is only one center number can be set.

Locator Data Upload Interval

Users can modify GPRS uploading time interval by SMS

TIMER,T1,T2#
T1 ranges 5-18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 20;
T2 ranges 5-18000 or 0(seconds), upload interval when ACC OFF, 0 means no upload, default is 20

Arming time setting

Delay time for device entering arming state after the vehicle power is off and ACC is in low-level. In the arming state, if the vehicle
vibrates for a few times, it will activate the vibration alarm system. If the vehicle battery is still not on (ACC is in low level) after 3
minutes, the device will start vibration alarm.

SMS format:

DEFENSE,TIME#

The time ranges from 1 to 60 minutes, default is 1.

NOTE:

1. Preset SOS numbers before sending SMS alarm messages and

2. If there is no need for vibration alarm, please SMS SENALM,OFF# to close it.

Check parameter setting

You can check the parameter setting by command:

PARAM#

Example: PARAM# Information replied:

IMEI: 358735070292023; TIMER: 20,20; SENDS:3; SOS:„;
Center Number:; Sensorset:10,3,5,1; Defense time:1; TimeZone:E,8,0;
The replied information contains IMEI number GPS data uploading Interval, GPS working time, SOS number center number, sensor
time interval, defense time and time zone info.

Check GPRS parameters

SMS command format :
GPRSSET#
Example: GPRSSET# Reply message:
GPRS:ON; Currently use APN:cmmtm„; Server:1,
GPSDEV.TRACKSOLID.COM,21100,0;
URL:http://maps.googIe.com/maps?q=;

Operation of device

Power on/Power off

Power on: Once insert a valid SIM card and connect all the wires, turn on the device, then Power LED will flash first, during signal
searching process, GSM and GPS LED will flash. Once GPS LED keeps slow flashing, it means the device has been located and it
starts to work. Power off: Just turn off the power switch. The device will begin to upload positioning data to server once inserting a
valid SIM card and power on. During the working time, it can upload data to server every 10 seconds.

NOTE:

To power on / power off, please remove the back cover first, refer to 4. Getting Started.

Check location

1. Via SMS
SMS “WHERE# ’ to the SIM number of device. The device will send a location message automatically. You can get the
coordinates. If the device does not search any information of location, it will send “No data” to the cell phone. Example: Current
position! Lat:N22.577156,Lon:E113.916748,Course:131.99,Speed:0. 00Km/h,Date Time:2013-10-08 17:35:32 SMS “URL# ’ to
the SIM number of device. The device will send a location Google Map link. If the device does not search any information of
location, it will send “No data” to the cell phone. Example: <1 0-08 17:36>http://maps.googIe.com/maps?q=N22.5771 56,E1
13.916748
2. V1a platform
Go to the platform website offered by dealers to check your vehicle location.

Wire cut-off alarm

When the electricity supply of device is cut off, it will activate cut-off alarm. In this case, the device will send related SMS to the
SOS numbers and dial the numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the meantime, the
device will upload power cut off alarm data to the server. And it will send: Cut Power ! <Date Time:13-06-17 14 : 53 : 06>,
http://maps.googIe.com/maps?q=N22576713,E1 13.916585

NOTE:

The SOS numbers should be preset, please refer to 5.1.

Low battery alarm

When the device is only working with battery, once the internal voltage of battery is less than 3.7V, device will send low battery
alarm SMS to SOS number and alarm on platform. Low battery alarm SMS content example:”Attention!!!Battery is too low, please
charge.” Which means the battery is too low, inform user charging it in time.

NOTE:
The SOS numbers should be preset, please refer to 5.1.

Vibration alarm

The vibration alarm function is off by default. To activate this function, please send the following command: SENALM, ON#
ACC OFF & in arming state If 5 times (times can be set) of vibration detected in 10 seconds, 1) ACC OFF in the following 30
seconds, the device will send vibration alarm. 2) ACC ON in within 30 seconds, no vibration alarm will be triggered.

NOTE:

1. The SOS numbers should be

2. Send “SENALM, OFF#” to turn off the vibration alarm if don’t

Oil cut-off

1. via plat form

Send oil cut-off command on platform. To make sure the security of vehicle, tracker can only indicate to cut off oilwhen GPS is
in valid position status, and the speed is less than 20KM/H or in static. Platform account password is needed when sending oil
cut off command.
2. Via SMS
Firstly, you should set a center number. Please refer to 5.4. Only center number can send the command to the device to cut
 off and restore oil.
The format is: RELAY,1#
After the command is carried out, it will reply “Cut off the fuel supply: Success! Speed:0 Km/h”. If the command didn’t carry out,
it will reply the reason about fail to carry out.
NOTE:
To ensure the safety of the driver and the car this command is valid only under two conditions: the GPS is located; the speed
is less than 20km/h.

Restoring Oil

1. Via platform
When the alarm is off, sending recover oil commands manually. Device will restore oil supplying, and vehicle will work
normally again.
Platform account password is needed when sending oil cut off command.

2. Via SMS

Only center number can send the command to the device to restore oil. The format is: RELAY,0# After the command is carried out,
it will receive “Restore fuel supply: Success!”

Over Speed Alarm

When the car is moving over a limited speed in average in a limited time period, then the device will send over speed alarm SMS to
user. To turn on the over speed function, please send below SMS command: SPEED,ON,Time,Limited speed,way of alarm# Time
range (Second) : 5-600s (default as 20s). Limited speed range (km/h) : 1-255, default: 50. Way of alarm: 0, GPRS only; 1,
SMS+GPRS; default: 1. Example: SPEED,ON,10,120,1# Means when the car is moving over 50km/h in average in 10 seconds, the
device will send over speed alarm to user.

Restore to factory setting

SMS command format: “FACTORYS” to set all parameter to default factory value. Once received “OK! The terminal will restart
after 60s!”, it succeeds.

Reboot device

When there is something wrong with the link of GPRS, e.g., the parameter setting of the device is correct, but you can’t track the car
on the platform. At this moment you can send a command to the device to reboot the device. The format is: RESET# After receiving
this command, the device will reboot after 20 seconds

Platform

Login www.tracksolid.com by account name and password. The function on the GPS platform can be realized as follows:

Real-time Tracking
Report and Statistics
Online Configuration

Troubleshooting

If you are having trouble with your device, try these troubleshooting procedures before contacting a service professional
Problems Causes

Red LED does not work when power

The fuse blows Replace the fuse
connected

Check SIM card installation ( • 4.1 Install

Wrong installation of SIM card
SIM card)

Filth on the SIM card iron surface. Clean it

Useless SIM Contact internet service provider

Fail to connect network Check installation of device( ¥• 4.4 Install

Improper installation
the device)

Beynd GSM service area Use it in effective GSM service offer area

Try again in a better

Bad signal
signal area

The voltage is unsuitable Connect with power with suitable voltage

Fail to charge

Improper connection Check connection with charger

This device is only for use with 12V. 24V, 36V, 48V. or 72V vehicles. One side of the device is marked THIS SIDE TOWARDS
SKY”, place the unit upside down will result in connection issues. Avoid placing the device somewhere that metal will be covering it
up.

File Downloads

Concox User Manual Download [optimized]

WeTrack2 General Vehicle GPS Tracker Download

Related Manuals

1. teltonika GPS Tracker User Manual teltonika GPS Tracker Know your device Pinout Table 1 FMB130...
2. DAKWIT GPS TRACKER User Manual DAKWIT GPS TRACKER User Manual REFACE Thank you for purchasing...
3. SinoTrack GPS TRACKER User Manual SinoTrack GPS TRACKER USER MANUAL PREFACE Thank you for purchasing...
4. D35 GPS tracker User Manual D35 GPS tracker Thank you for choosing our GPS tracker....
5. LKGPS LK209 GPS Tracker User Manual Power magnetic GPS Tracker Manual Preface LK209 Thank you for...
6. SinoTrack GPS Tracker ST-901 User Manual GPS Tracker ST-901 User Manual LED Status Blue LED— GPS...