Translated from German to English - www.onlinedoctranslator.

com

Revision: 2020-145

MQB encodings

© 2013-2020 Daniel Fuchs page 1

Contents

Foreword................................................. .................................................. .................................................. .................................................. ..........................................10

Access Permissions ..................................................... .................................................. .................................................. .................................................. .................10
Cornering light - deactivation ................................................ .................................................. .................................................. .................................................. ..........11
Cornering light - change standard/regulation................................................. .................................................. .................................................. ................................................11
Cornering light - changing the speed of the dimming........................................ .................................................. .................................................. .....................12
Cornering light - adjust speed threshold................................................. .................................................. .................................................. .......................12
Low beam - automatic activation as permanent driving light from speed .......................................... .................................................. ..................................12
ACC - configure distance setting in the MMI (Audi A3 8V) ........................................ .................................................. .................................................. ...............12
Change ACC step setting to 1 km/h (Audi A3 8V) ...................................... .................................................. .................................................. ............................12
ACC - prevent/allow overtaking on the right (variant 1) ........................................ .................................................. .................................................. ...................12
ACC - prevent/allow overtaking on the right (variant 2) ........................................ .................................................. .................................................. ...................12
Four-wheel drive - increase locking measures for more traction................................................. .................................................. .................................................. ....................13
Ambient lighting (multicolored) - Activation/Release........................................ .................................................. .................................................. ..........13
Ambient lighting (multicolor) - adjust colors ................................................ .................................................. .................................................. .......................14
Ambient lighting (multicolored) - Colors expand to 30 possibilities ........................................ .................................................. ........................................15
Ambient lighting (multicolored) - change color assignment to driving profile ........................................ .................................................. ............................................15
Ambient lighting - Deactivate dimming of the door lighting................................................. .................................................. ................................................15
Ambient lighting - adjust colors (Leon III 5F)......................................... .................................................. .................................................. .......................16
Trailer hitch - activation/activation (retrofit) ................................................ .................................................. .................................................. ............16
Trailer maneuvering assistant (Trailer Assist) - activation/activation......................................... .................................................. .................................................. ...17
Assistant light function - change light sensor sensitivity ........................................ .................................................. .................................................. .............17
Disabling exhaust flap control ........................................ .................................................. .................................................. .......................................17
Auto Hold - Customization of dynamic hold assist ................................................ .................................................. .................................................. ...............17
Auto Hold - state after restart ............................................ .................................................. .................................................. .................................................. ....18
Auto-Lock also locks the fuel filler cap ........................................ .................................................. .................................................. .......................................18
Teach-in battery after change ................................................ .................................................. .................................................. .................................................. ......18
Front passenger airbag - deactivate button........................................ .................................................. .................................................. .................................................18
Hill Start Assist - Activation of the HHC........................................ .................................................. .................................................. .......................................18
Hill Start Assist - Set hold time................................................. .................................................. .................................................. ..........................................18
Rear turn signals active when tailgate is open ........................................ .................................................. .................................................. ..................................19
Adapting the brake disc drying ................................................ .................................................. .................................................. ................................................19
Coming Home/Leaving Home - Emulation via interior light......................................... .................................................. .................................................. .....................19

© 2013-2020 Daniel Fuchs Page 2

Coming Home/Leaving Home - set the light duration >30 seconds......................................... .................................................. .................................................. ....20
Coming Home/Leaving Home without dipped headlights (only daytime running lights or parking lights) ..................................... .................................................. ...................................20
Coming Home/Leaving Home via fog lights ........................................ .................................................. .................................................. ..........................20
Coming Home/Leaving Home - daytime running lights at full intensity ........................................ .................................................. .................................................. .................20
Adjust Coming Home switch-on trigger ................................................ .................................................. .................................................. ........................................21
Coming Home function automatically................................................. .................................................. .................................................. .................................................21
Discover Media/Pro - Current location in the header instead of the selected driving profile.................................... .................................................. ................................................21
Discover Media/Pro - Activate off-road displays (MIB 2) ........................................ .................................................. .................................................. .......................21
Discover Media/Pro - Activate online services (MIB 2) ........................................ .................................................. .................................................. .......................21
Discover Media/Pro - Enable Wi-Fi Streaming (MIB2) ........................................ .................................................. .................................................. ........................22
Discover Media/Pro - Allow second phone via Bluetooth ........................................ .................................................. .................................................. ............22
Discover Pro - Change boot animation ................................................ .................................................. .................................................. .................................................22
Activate Discover Pro - Green Menu ............................................ .................................................. .................................................. .................................................22
Discover Pro - Show speed limit from map data................................................. .................................................. ................................................23
Discover Pro - Disable radio modulation AM................................................ .................................................. .................................................. ................................23
Discover Pro - Change skin................................................. .................................................. .................................................. .................................................. .................23
Discover Pro - Enable Wi-Fi Streaming (MIB 1) ........................................ .................................................. .................................................. ..................................23
Third brake light as a receipt for the central locking ....................................... .................................................. .................................................. ...............23
Third brake light active when the tailgate is open ........................................ .................................................. .................................................. .......................24
Third brake light also flashes when the hazard warning lights are active................................................. .................................................. .................................................. ................24
DWA - activation/release (retrofitting) ................................................ .................................................. .................................................. ...................................24
DWA - activation of the horn acknowledgment when locking and unlocking the vehicle......................................... .................................................. .......................25
DWA - Start of the alarm on mechanical opening (Thatcham) ........................................ .................................................. .................................................. ..............25
Dynamic high beam (DLA) - activation (up to MY 2016) ........................................ .................................................. .................................................. .......................25
Dynamic high beam (DLA) - activation (from MY 2017) ........................................ .................................................. .................................................. .......................26
Parking aid - change switch-off speed ........................................ .................................................. .................................................. .................................26
Parking assistance - disable activation sound ................................................ .................................................. .................................................. .......................................26
Parking assistance - deactivate audio attenuation................................................. .................................................. .................................................. ......................................26
Parking assistance - automatic activation when driving slowly forward ........................................ .................................................. .................................................. 27
Parking Assist - Adjust Curb Distance (Trigger Continuous Tone/Last Stage) ........................................ .................................................. .......................................27
Parking aid - Activate display, despite small parking aid (Leon III 5F, Audi A3 8V)................................. .................................................. ................................27
Parking aid - activate/deactivate guide lines................................................. .................................................. .................................................. ................................27
Parking assistance - adjust volume front/rear ................................................ .................................................. .................................................. ...................................27
Parking Aid - Front/Rear pitch adjustment................................................. .................................................. .................................................. ......................................27
© 2013-2020 Daniel Fuchs page 3
Electronic parking brake (EPB) - deactivation of automatic activation when seat belt is unbuckled......................................... .................................................. ........27
ESP - Change available modes (ASR off / ESC Sport / ESC off) ..................................... .................................................. .................................................. ...................28
Activating driving school mode (display of speed and indicators on the radio, only possible with Composition Colour/Touch and Discover Media) .....................28
Window operation - do not cancel release run-on when opening the door ........................................ .................................................. ................................................28
High-beam assistant (Light Assist/HBA) - activation (variant 1) ..................................... .................................................. .................................................. ..............28
High beam assistant (Light Assist/HBA) - activation (variant 2) ..................................... .................................................. .................................................. ..............29
High-beam assistant (Light Assist) - adjust switch-on and switch-off times................................................. .................................................. ........................................29
High-beam assistant (Light Assist) - deactivate reset ........................................ .................................................. .................................................. .......................29
High beam assistant (Light Assist) - deactivate city recognition ........................................ .................................................. .................................................. ............29
Recalibrate the front/forefield camera after lowering ........................................ .................................................. .................................................. .....................29
Front Assist - pre-warning - Activate early/medium/late selection...................................... .................................................. .................................................. ............30
Front Assist - pre-warning - save selected value......................................... .................................................. .................................................. ...................30
Windscreen wipers - park when bonnet is opened ........................................ .................................................. .................................................. .......30
Windscreen wipers - parking when ignition is switched off (Octavia III 5E) ................................................ .................................................. .....................................30
Windscreen wipers - set the service position via the menu (Audi A3 8V)........................................ .................................................. ................................................30
Windscreen wipers - activate teardrop wipers................................................. .................................................. .................................................. ............................31
Windscreen wipers - adjust wipe cycles per minute ........................................ .................................................. .................................................. ................31
Windscreen wipers - activate teardrop wipers at the front ........................................ .................................................. .................................................. ....................31
Enabling run-on of the power windows after ignition off ................................................ .................................................. .................................................. .......................31
Footwell lighting - activation/activation (retrofitting) ........................................ .................................................. .................................................. ........31
Footwell lighting - activation/activation, multicolored (retrofit) ........................................ .................................................. ........................................32
Footwell lighting - activate the ambient lighting function (Audi) ........................................ .................................................. .......................................32
Footwell lighting - conversion to LED - prevent error messages in the BCM ........................................ .................................................. ...................................32
Disabling the yellow mode switch light ........................................ .................................................. .................................................. .......................................32
Activate trailer stabilization ..................................................... .................................................. .................................................. .................................................. ...32
Transmission - disable freewheel ................................................ .................................................. .................................................. .................................................. .......33
Tailgate (electric) - opening/closing while driving ...................................... .................................................. .................................................. .......33
Tailgate (electric) - opening/closing when towing a trailer ........................................ .................................................. .................................................. ..........33
Tailgate (electric) - opening/closing via button in the center console and FFB................................... .................................................. ....................................33
Tailgate (electric) - changing the opening height......................................... .................................................. .................................................. ...................................33
Tailgate (electric) - Monitoring for keys in the trunk (KESSY) ..................................... .................................................. .......................................33
Tailgate (electric) - Do not stop closing when leaving the close-up area ...................................... .................................................. .......................34
Tailgate (electric) - allow closing with the key from a greater distance ..................................... .................................................. .......................34
Tailgate (electric) - adjust or disable warning signals ........................................ .................................................. .................................................. ......34
© 2013-2020 Daniel Fuchs page 4
Close the tailgate with a time delay (30 seconds) after opening it individually ........................................ .................................................. .................................................. .....34
Tailgate lights remain on when the lid is opened (Golf 7 AU, Audi A3 8V) ................................ .................................................. ..................................34
Heated rear window - adjust heating duration ................................................ .................................................. .................................................. .....................................35
Disabling the rear wiper ..................................... .................................................. .................................................. .................................................. ..............35
Rear wiper - activate automatically when the front wiper is active at level 2 or higher ........................................ .................................................. ..........................35
Rear wiper - deactivate automatic wiping when reverse gear is engaged......................................... .................................................. .......................35
Rear wiper - activate teardrop wiper ................................................ .................................................. .................................................. .......................................35
Rear wiper - Adjusting the wiping interval of the wiper ........................................ .................................................. .................................................. .......................35
HUD - move display horizontally ................................................ .................................................. .................................................. ................................................35
HUD - move display vertically ................................................ .................................................. .................................................. .................................................. ..36
Infotainment - Activating Apple Wireless Carplay (Audi)......................................... .................................................. .................................................. ........................36
Infotainment - removing or activating the chute lock ................................................ .................................................. .................................................. ...................36
Infotainment - Activate welcome sound (Audi)................................................. .................................................. .................................................. ................................36
License plate light - conversion to LED................................................. .................................................. .................................................. ..................................36
KESSY - Automatic locking when the doors are closed (3Q0 control unit) ........................................ .................................................. ...................................36
KESSY - Automatic locking when the doors are closed (5Q0 control unit) ........................................ .................................................. ...................................37
KESSY - Activate staging/pulsing of the start button ........................................ .................................................. .................................................. ...................37
KESSY - activate convenience opening .................................................. .................................................. .................................................. .................................................. ....37
KESSY - Temporary deactivation - activation (3Q0 control unit) ........................................ .................................................. .................................................. .....37
KESSY - Temporary deactivation - activation (5Q0 control unit) ........................................ .................................................. .................................................. .....38
KESSY - Deactivate door sensors ........................................ .................................................. .................................................. .................................................. ....38
KESSY - Activate locking via Easy Close (3Q0 control device) ........................................ .................................................. .................................................. ............38
Air conditioning - Air Care - Activation................................................ .................................................. .................................................. .................................................. 38
Air conditioning - Air Care - save status................................................. .................................................. .................................................. .......................................38
Air conditioning - setting the sensitivity of the interior humidity sensor ........................................ .................................................. .....................................38
Air conditioning - display blower level also in AUTO mode (not Audi A3 8V) ..................................... .................................................. .......................................39
Air conditioning - change the brightness of the LCD temperature display ........................................ .................................................. .................................................. ......................39
Air conditioning - Brightness of LEDs for current fan speed ................................................ .................................................. .................................................. ..........................39
Air conditioning - brightness of LEDs for seat heating......................................... .................................................. .................................................. .......................................39
Air conditioning - brightness LEDs (rest) ................................................ .................................................. .................................................. .................................................. ....39
Air conditioning - Activating the offset logic for the blower level ........................................ .................................................. .................................................. ....................39
Instrument cluster - deactivate seat belt reminder................................................. .................................................. .................................................. .....................................40
Combined instrument - change reserve tank volume ........................................ .................................................. .................................................. ................................40
Instrument cluster - dial lighting also active with parking lights ........................................ .................................................. .................................................. ........40
© 2013-2020 Daniel Fuchs page 5
Instrument cluster - change skin................................................. .................................................. .................................................. .................................................. ........40
Instrument cluster - change scale display (VC/AID/FPK) ........................................ .................................................. .................................................. ....................40
Instrument cluster - adjust maximum speedometer (VC/AID/FPK) ........................................ .................................................. .................................................. ...................40
Instrument cluster - activate pointer test (staging) ........................................ .................................................. .................................................. .......................40
Instrument cluster - Ignition active adjust/deactivate message ................................................ .................................................. .................................................. .....41
Convenience actions via FFB even while the ignition is on/the engine is running ........................................ .................................................. .................................................. .........41
Changing the flashing cycle for convenience................................................. .................................................. .................................................. .................................................. .41
Deactivating convenience turn signals................................................ .................................................. .................................................. .................................................. ..........41
Change steering characteristics without driving profile selection ................................................ .................................................. .................................................. ..................................41
Heated steering wheel - automatic activation ........................................ .................................................. .................................................. .....................................41
Adjust steering assistance ................................................ .................................................. .................................................. .................................................. .........42
Adapt steering support directly when changing driving profile (instead of incremental change) ........................................ .................................................. ...................42
Adapting the light switch-on threshold (Leon III 5F) ........................................ .................................................. .................................................. .......................................42
Headlight flash also activates fog lights................................................. .................................................. .................................................. ................................42
Headlight flash during the day via fog lights ........................................ .................................................. .................................................. .......................................42
Headlight flash possible with ignition off ........................................ .................................................. .................................................. .................................................. ..43
Light/rain sensor - activation/activation (retrofitting) ........................................ .................................................. .................................................. ...............43
Light/rain sensor - activate rain closing ................................................ .................................................. .................................................. ..................................44
MFA - adjust the display duration for the rear seat belt display........................................ .................................................. .................................................. ............................44
MFA - Adjust display time for service reminder ........................................ .................................................. .................................................. ..........................44
MFA - adjust display duration for warning messages ............................................ .................................................. .................................................. .......................44
MFA - briefly display the driving profile when changing........................................ .................................................. .................................................. ......................................44
MFA - Deactivate the message "Switch on low beam"................................................. .................................................. .................................................. .......................45
MFA - Display compass at the bottom................................................. .................................................. .................................................. ........................................45
MFA - Display volume to be refueled................................................. .................................................. .................................................. .......................................45
MFA - show oil temperature................................................. .................................................. .................................................. .................................................. ..........45
MFA - Show lap counter/lap timer................................................. .................................................. .................................................. ................................................45
MFA - show shift recommendation (Audi A3 8V)......................................... .................................................. .................................................. .....................................45
MFA - warning when driving with rear fog light ........................................ .................................................. .................................................. .......................45
MFA - warning when driving with active side lights ................................................ .................................................. .................................................. .......................46
MFA - warning at speeds above 120 km/h ........................................ .................................................. .................................................. ........................46
MFA - Adjust/deactivate warning of ice danger................................................. .................................................. .................................................. ....................46
MFA - warning notice danger of slippery re-submission after engine off ........................................ .................................................. .................................................. ........46
MFA - display cylinder deactivation (ACT / COD) ........................................ .................................................. .................................................. ..................................46
© 2013-2020 Daniel Fuchs page 6
Adjust microphone sensitivity................................................ .................................................. .................................................. .................................................. 46
Multifunction steering wheel - activation/activation (retrofit) (Audi A3 8V) ..................................... .................................................. .......................................46
Fog lights - activation/activation (retrofitting) ........................................ .................................................. .................................................. .............47
Fog lights - Activating cornering lights ................................................ .................................................. .................................................. .....................................47
Fog Lights - Unlock Crossing Lights........................................................ .................................................. .................................................. ................................48
Fog lights - conversion to LED (Octavia III 5E)........................................ .................................................. .................................................. .......................48
Rear fog lights - both active (Octavia III 5E)......................................... .................................................. .................................................. ................................48
Personalization - Activation (Variant 1) ........................................ .................................................. .................................................. .......................................48
Personalization - Activation (Variant 2) ........................................ .................................................. .................................................. .......................................49
Pace car flashing rear lights (LED rear lights) (Golf 7 AU) .................................. .................................................. .................................................. ............50
Pace car rear lights flashing (only when opening/closing the vehicle) (LED rear lights) (Golf 7 AU) .......................... .................................................. ........... 50
Pace car flashing of the rear lights (only when flashing the hazard) (LED rear lights) (Golf 7 AU)............................. .................................................. ............................51
Parking light on both sides ........................................ .................................................. .................................................. .................................................. .......................51
Radio receiver amplifier ..................................................... .................................................. .................................................. .................................................. .............52
Tire pressure control display (direct, TPMS) - activation/activation........................................ .................................................. .................................................. ..52
Tire pressure monitoring display (indirect, via ABS) - activation/activation (retrofitting) ..................................... .................................................. .......................52
Reversing camera (low) - activation/activation (retrofit)....................................... .................................................. .................................................. ..........53
Reversing camera (Low) - Disable deactivation when tailgate is open ........................................ .................................................. ..........................................53
Reversing camera (Low) - switch off speed-dependent deactivation......................................... .................................................. ....................................53
Increasing the luminosity of the reversing light (Golf 7 AU) ........................................ .................................................. .................................................. ......................................53
Sliding roof - make the display position accessible directly from the sliding position .................................. .................................................. .................................................. ..54
Sunroof - Do not cancel the closing process when the door is opened (with STG CA) ........................................ .................................................. ............................................54
Sunroof - Do not cancel the closing process when the door is opened (without STG CA)........................................ .................................................. ..........................................54
Sliding sunroof - change mode for convenience opening ................................................ .................................................. .................................................. .......................54
Sunroof - decouple roller blind from the roof (with STG CA)......................................... .................................................. .................................................. ..........................54
Sunroof - decouple roller blind from the roof (without STG CA) ........................................ .................................................. .................................................. .......................54
Inside tail light active at Coming Home/Leaving Home ............................................ .................................................. .................................................. .....................55
Rear light inside double function as brake light (for LED rear lights) (Golf 7 AU)................................. .................................................. ...................................55
Tail light, inside, double function as brake light (for halogen tail lights) (Golf 7 AU) .................................. .................................................. .......................55
Deactivate tail light inside double function as brake light with active rear fog light (legal requirement according to StVZO) ..................................... ...................55
Seats - Activate "Easy Entry" (electric seats) ...................................... .................................................. .................................................. ............55
Seats - Comfort entry "Easy Entry" Activate menu entry (electric seats) ..................................... .................................................. .......................................56
Seat heating - Adjusting the temperatures of the stages ........................................ .................................................. .................................................. ................................56
Seat heating - save the selected seat heating level ........................................ .................................................. .................................................. .......................56
© 2013-2020 Daniel Fuchs page 7
Seat heating - adjust return thresholds (Audi A3 8V) ........................................ .................................................. .................................................. ...................57
Set daylight saving time automatically................................................. .................................................. .................................................. .................................................. 57
Deactivating the sound actuator or reducing the volume................................................. .................................................. .................................................. .....................57
Sound system - expansion of the internal sound system (without ext. amp) with virtual surround and subwoofer .................................. ........................................57
Mirror - activate lowering of the passenger side ............................................ .................................................. .................................................. ................................57
Mirror - Folding - Activation ................................................ .................................................. .................................................. .................................................. 58
Mirrors - folding also active while driving................................................. .................................................. .................................................. ................................58
Adjust mirror folding via FFB mode ................................................ .................................................. .................................................. ...................................58
Mirrors - ambient lighting active when mirrors are folded in ................................................ .................................................. .................................................. ............58
Spoiler - do not lower when locking the vehicle (Audi TT 8S) ..................................... .................................................. .................................................. ....58
Spoiler - do not lower automatically after manual extension (Audi TT 8S) ...................................... .................................................. .......................................59
Activate voice control (Audi A3 8V)................................................. .................................................. .................................................. .......................................59
Lane Keeping Assist (Lane Assist) - Activation (Variant 1) ........................................ .................................................. .................................................. ...................59
Lane Keeping Assist (Lane Assist) - Activation (Variant 2) ........................................ .................................................. .................................................. ...................60
Lane Keeping Assist (Lane Assist) - Activation (Variant 3) ........................................ .................................................. .................................................. ...................60
Lane Departure Warning - Driver Inactivity Deactivation Threshold ................................................ .................................................. .................................................. ....61
Lane departure warning system - setting the time of intervention via the menu......................................... .................................................. .................................................. ........61
Lane Departure Warning - Adjusting the intensity of the steering wheel vibration........................................ .................................................. .................................................. ...........61
Lane Departure Warning - Adjusting the intensity of the steering assistance........................................ .................................................. .................................................. ........62
Lane departure warning system - set the warning strength via the menu (variant 1) ........................................ .................................................. .................................................. ......62
Lane departure warning system - set the warning strength via the menu (variant 2) ........................................ .................................................. .................................................. ......62
Auxiliary heating - adjust post-heating time ................................................ .................................................. .................................................. ................................................62
Auxiliary heating - adjust the temperature for activating the interior fan ........................................ .................................................. .....................................62
Auxiliary heater - adjust temperatures for auxiliary heater operation ........................................ .................................................. .................................................. .............62
Deactivate start/stop function................................................. .................................................. .................................................. .................................................. ...63
SWRA - deactivation................................................ .................................................. .................................................. .................................................. ......................63
SWRA - change the delay time until triggering......................................... .................................................. .................................................. .......................63
SWRA - adjust washing behavior (frequency, duration) ............................................ .................................................. .................................................. ..........................63
Daytime running lights - switch off when the handbrake is pulled ........................................ .................................................. .................................................. ........................63
Daytime running lights - dimming when blinking ........................................ .................................................. .................................................. .................................................. .64
Daytime running lights - dimming when blinking (slow dimming) (Seat Leon 5F).................................... .................................................. .................................................. .64
Daytime running lights - deactivate dimming when flashing (Audi A3 8V)......................................... .................................................. .................................................. ...............64
Daytime running lights - Simultaneous flashing with the turn signal (or alternately) ........................................ .................................................. .................................................. .64
Daytime running lights - inactive in LDS position 0......................................... .................................................. .................................................. .................................................. .65

© 2013-2020 Daniel Fuchs page 8

Daytime running lights - Activate menu item in the CAR menu ........................................ .................................................. .................................................. ................................65
Daytime running lights - fog lights only as daytime running lights ........................................ .................................................. .................................................. ........65
Daytime running lights - add fog lights in addition to daytime running lights......................................... .................................................. .......................................65
Daytime running lights - rear lights also active (with KZB and interior button = parking light always active)................................... .................................................. .................66
Daytime running lights - rear lights also active (without KZB) ........................................ .................................................. .................................................. ..........................66
Daytime running light - parking light point also active (Golf 7 AU) ........................................ .................................................. .................................................. ......................66
Fuel Gauge - Adjustment/Calibration ................................................ .................................................. .................................................. ................................................66
Button illumination (driving profile, ASR, ESP) adjust brightness ........................................ .................................................. .................................................. ................66
Traffic Jam Assist (traffic jam assistant) & Emergency Assist - Activation ........................................ .................................................. .................................................. .....67
Ambient lighting - activation/activation (retrofitting) ........................................ .................................................. .................................................. ...........67
Perimeter lighting - use as a maneuvering light................................................. .................................................. .................................................. ..................67
US parking light explicitly only in switch position parking light ........................................ .................................................. .................................................. .......................67
Emulate US parking lights via ambient lighting (dimmable/switchable in the CAR menu) .................................... .................................................. ..........................68
Controlling the US side lights via the Sport driving profile (Leon III 5F) ...................................... .................................................. .................................................. ..........................69
US daytime running lights or parking lights (indicators permanently dimmed with daytime running lights or parking lights/dipped beam)................................. ................................................69
US daytime running lights or parking lights - cancellation of dimming when blinking......................................... .................................................. .................................................70
US daytime running lights in addition to the normal daytime running lights - switchable via the CAR menu ..................................... .................................................. ....................................70
US daytime running lights/normal daytime running lights - switchable via CAR menu......................................... .................................................. .................................................. ..........71
Adapt consumption display ................................................ .................................................. .................................................. .................................................. .........72
Activate voice control (Audi A3 8V)................................................. .................................................. .................................................. .......................................72
Traffic Sign Recognition - Activation (Variant 1) ........................................ .................................................. .................................................. ......................72
Traffic Sign Recognition - Activation (Variant 2) ........................................ .................................................. .................................................. ......................73
Traffic Sign Recognition - Display Cancellation Signs........................................ .................................................. .................................................. ..............73
Video in Motion (VIM) - Activation ........................................ .................................................. .................................................. .................................................. .73
Hazard warning lights - automatic activation after hard braking......................................... .................................................. .................................................. .............73
Hazard warning button - Adjusting the brightness of the lighting ........................................ .................................................. .................................................. .......................74
XDS - Enhanced electronic differential lock adjust control strength ................................................ .................................................. ......................................74
Central locking - adjust the duration of the visual feedback ........................................ .................................................. .................................................. ....74
Central locking - do not unlock when removing the key ........................................ .................................................. .................................................. ..........74

© 2013-2020 Daniel Fuchs page 9

foreword

The codings and adjustments listed here are from various sources and mostly tested on a vehicle or found and documented by yourself. This
document does not claim to be correct. All changes are therefore made at your own risk.

It is recommended to create a full auto scan and adaptation channel maps (“AdpMap”) of all control units that are to be adapted before making
the changes.

Instructions for creating an adaptation channel image:

Start VCDS > Applications > Control unit image > Address "XX", access authorization "YYYYY", function "Adaptation", format "CSV file" > Start The access
authorizations can be found in the next chapter.

Access Permissions
control unit Log in function
01 (engine electronics) 27971 Customization Unlock
79153 ???
03 (brake electronics) -------- (Logins without a known function are not listed for this STG due to the volume)
11966 Unlock Hydraulic Brake Assist Customization (IDE05055)
20103 Unlocking the adjustment of the ext. electronic differential lock XDS (IDE05286)
24990 Customization Unlock
25757 Unlock Brake Stabilization Adaptation (IDE05161)
25004 Brake booster adaptation
31857 Activation of the basic setting and customization
40168 Activation of the basic setting
40304 / 44595 Activation of the adaptation of the brake disc drying (IDE04456)
05 (entry/start area) 20103 ???
08 (air conditioning/heating el.) 20103 ???
09 (central electrics) 31347 Customization Unlock
48396 Activation of customization (only Tiguan MY 2016)
10 (parking aid 2) 20103 ???
71679 Enabling the coding
13 (distance control) 14117 Customization Unlock
14 (wheel damping) 20103 ???
17 (dash panel insert) 20103 Customization unlock (before MY 2016)

© 2013-2020 Daniel Fuchs Page 10

 25327 ??? (from MY 2016)
47115 Activation of customization (from MY 2016)
18 (auxiliary heating) 20103 ???
19 (diagnostic interface) 20103 ???
2B (Steering Column Lock) 20103 ???
3C (lane change) 20103 ???
42 (door electric driver) 20103 ???
44 (steering assistance) 19249 Customization Unlock
28183 Activation of the adjustment of the driving profile switch (IDE06419)
44595 ???
4B (multifunction control) 20103 ???
52 (door electr. passenger) 20103 ???
55 (headlight range control) 15284 Customization Unlock
20103 ???
5F (Information Elec. I) 20103 ???
65 (tire pressure) 20103 Customization Unlock
6D (Tailgate) 12345 Customization Unlock
A5 (front/fore camera) 20103 Customization Unlock
75 (telematics) 20103 ???

Cornering light - deactivation

STG 09 > Access authorization: 31347 > Adaptation > "Static cornering light regulation" channel > Change value to "off" (factory setting: ECE R119)

Cornering light - change standard/regulation

STG 09 > Access authorization: 31347 > Adaptation > "Static cornering light regulation" channel > Adapt value

"ECE R119" > cornering light is already activated when stationary (factory setting)
"ECE R48" > cornering light is only activated from 1 km/h, i.e. only when rolling

© 2013-2020 Daniel Fuchs page 11

Cornering light - change the dimming speed
STG 09 > Access authorization: 31347 > Adaptation > "Static cornering light dimming speed" channel > Adapt value [% value per second]
(factory setting: 50% per second = 2 seconds)

Cornering light - adjust speed threshold

STG 09 > Access authorization: 31347 > Adaptation > "Static cornering light upper speed threshold" channel > Adapt value in km/h
(factory setting: 40)

Low beam - Automatic activation as permanent driving light from speed

STG 09 > access authorization 31347 > customization > …

> Channel "Headlights and parking lights - all-weather light switch-on limit" > Adjust speed in km/h
> Channel "Headlights and parking lights - all-weather light switch-off limit" > Adjust speed in km/h

ACC - configure distance setting in MMI (Audi A3 8V)

STG 13 > Access Permission: 14117 > Customization > Channel "Time Gap Preset Choice" > Change value to "on".

ACC - change step setting to 1 km/h (Audi A3 8V)

STG 13 > Coding > Byte 14 > Activate bit 4 ("Operation_mode")

ACC - prevent/allow overtaking on the right (variant 1)

An ACC control unit with part number 5Q0 is required.

STG 13 > Access Permission: 14117 > Adaptation > Channel "Avoidance for illegal overtaking" > Change value to "on" or "off".

ACC - prevent/allow overtaking on the right (variant 2)

An ACC control unit with part number 3Q0 or 2Q0 is required.

© 2013-2020 Daniel Fuchs page 12

STG 13 > Coding > Byte 02 > Activate or deactivate bit 5 ("Overtaking Right Prevention active")

Four-wheel drive - increase locking measures for more traction

For this function, the software version of the all-wheel drive control unit should be at least 7083. It may be necessary to update this to a compatible version
beforehand.

STG 22 > coding > byte 00 > …

> Deactivate bit 0

> Activate bit 1 and 2

STG 22 > Customization > …

> Channel "Acoustic measure: Tension logic" > Adapt value to "Increased traction".
> Channel "Acoustic measure: Benziner-Anti_hum_measure_benzin_gear_4" > Adjust value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_hum_measure_benzin_gear_5" > Adjust value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_hum_measure_benzin_gear_6" > Adjust value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_hum_measure_benzin_gear_7_plus" > Adjust the value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_impact_driver_measure_benzin_gear_4" > Adjust value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_impact_driver_measure_benzin_gear_5" > Adjust value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_impact_driver_measure_benzin_gear_6" > Adjust value to "no measure".
> Channel "Acoustic measure: Benziner-Anti_impact_driver_measure_benzin_gear_7_plus" > Adjust the value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_hum_measure_diesel_gear_4" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_hum_measure_diesel_gear_5" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_hum_measure_diesel_gear_6" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_hum_measure_diesel_gear_7_plus" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_impact_driver_measure_diesel_gear_4" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_impact_driver_measure_diesel_gear_5" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_impact_driver_measure_diesel_gear_6" > Adjust value to "no measure".
> Channel "Acoustic measure: Diesel-Anti_impact_driver_measure_diesel_gear_7_plus" > Adjust value to "no measure".

Ambient lighting (multicolored) - activation/activation

STG 09 > access permission: 31347 > customization > …

© 2013-2020 Daniel Fuchs page 13

 > Channel "Interior light 2nd generation - soft color change" > Adjust the value to "active".(if desired)
> Channel "Interior light 2nd generation center console lighting, multicolored" > Adjust the value to "active".(if installed)
> Channel "Interior light 2nd generation instrument panel lighting, multicolored" > Adjust the value to "active".(if AID installed)
> Channel "Interior light 2nd generation loudspeaker lighting, multicolored" > Adjust the value to "active".(if installed)
> Channel "Interior Light Lamp Configuration Ambience_Application Bars_in_Instrument Panel" > Adjust the value to "installed".
> Channel "Interior light lamp configuration - center console lighting" > Adjust the value to "installed".(if installed)
> Channel "Interior light Luminaire configuration-free_colour_choice_via_HMI" > Adjust value to "not active".
> Channel "Interior Light Luminaire Configuration-Ambient_Color List_HMI" > Adjust value to "active".
> Channel "Interior light lamp configuration - ambience menu with all zones" > Adjust the value to "active".
> Channel "Interior light lamp configuration ambient menu with global off" > Adjust value to "active".

After completing the coding, the infotainment must be restarted via the reset (hold the power button for 10 seconds).

Ambient lighting (multicolor) - Customize colors

The colors are given in RGB coding. If a color is set to {R:0, G:0, B:0}, the color will not be displayed. The first three channel blocks act for the
infotainment and the AID, the second three blocks for the LED ambience strips, which are controlled via the LIN bus. After completing the
coding, the infotainment must be restarted via the reset (hold the power button for 10 seconds).

Note: The colors are usually reproduced 1:1 in Infotainment and AID. Slight adjustments to the LIN colors may be necessary, since the colors
may differ there due to the different luminosity of the LEDs.

STG 09 > access permission: 31347 > customization > …

> Channels "Ambient light color list - red value color ?" > Adjust values in the range of 0-255
> Channels "Ambient light color list-green value color ?" > Adjust values in the range of 0-255
> Channels "Ambient light color list - blue value color ?" > Adjust values in the range of 0-255
> Channels "Interior light 2nd generation red value color ?" > Adjust values in the range of 0-255
> Channels "Interior light 2nd generation green value color ?" > Adjust values in the range of 0-255
> Channels "Interior light 2nd generation blue value color ?" > Adjust values in the range of 0-255

or (with newer control units)

> Channels "Ambient light color list - red value" > Adjust values in the range of 0-255
> Channels "Ambient light color list-Green value" > Adjust values in the range of 0-255
> Channels "Ambient light color list - blue value" Color ?" > Adjust values in the range of 0-255

© 2013-2020 Daniel Fuchs page 14

 > Channels "Ambient light color list LIN-Redvalue_Color_?_lin" > Adjust values in the range of 0-255
> Channels "Ambient light color list LIN-Gruenwert_Farbe_?_lin" > Adjust values in the range from 0-255
> Channels "Ambient light color list LIN-Blauwert_Farbe_?_lin" > Adjust values in the range of 0-255

Ambient lighting (multicolor) - colors expand to 30 possibilities

With »Facelift BCMs« (from Index BA) there are 20 additional color sets, which are assigned to the Ambience_lightning_color_list_2 &
Ambience_lightning_color_list_lin_2 group. The procedure is analogous to the adjustment of the colors in the previous chapter.

STG 09 > access permission: 31347 > customization > …

> channels "Ambience_lightning_color_list_2-red value color ?" > Adjust values in the range of 0-255
> Channels "Ambience_lightning_color_list_2-Green Value Color ?" > Adjust values in the range of 0-255
> Channels "Ambience_lightning_color_list_2-blue value color ?" > Adjust values in the range of 0-255
> Channels "Ambience_lightning_color_list_lin_2-Rotwert_Farbe_?_lin > Adjust value in the range of 0-255
> Channels "Ambience_lightning_color_list_lin_2-Gruenwert_Farbe_?_lin > Adjust value in the range of 0-255
> Channels "Ambience_lightning_color_list_lin_2-Blauwert_Farbe_?_lin > Adjust value in the range of 0-255

Ambient lighting (multicolored) - Change color assignment to driving profile

Activate STG 19 > Coding > Byte 11 > Bit 7 ("FPA_ Funktion_AMB")

STG 09 > access permission: 31347 > customization > …

> Channel "Interior light 2nd generation ambience_color choice_FPA_selectable_coupling" > Adjust the value to "active".
> Channel "Interior light 2nd generation ambience_color choice_FPA_waehlbare_kupplung_Status_hmi_default" > Adjust the value to "coupled".
> Channel "Ambient light Assignment of the color to the driving profile-driving profile_?" > Adjust value as desired

The assignment can differ depending on the gateway. This may need to be tried out. The color values are retrieved from the "Ambient light color list"
and "Ambient light color list LIN" channel lists. The function must then be activated in the CAR menu under ambient lighting.

Ambient lighting - disable dimming of door lighting

In the standard configuration, the ambient lighting is dimmed when the doors are closed and while driving. This can be deactivated.

STG 09 > access permission: 31347 > customization > … ©

2013-2020 Daniel Fuchs page 15

 > Channel "Interior lighting parameter-p_helligkeit_Tueren_closed_HD_zu_zuendung_aus_tueren" > Adjust the value to "100%".
> Channel "Interior lighting parameter-p_helligkeit_Fzg_closed_zuendung_ein_tueren" > Adjust the value to "100%".

Ambient lighting - adjust colors (Leon III 5F)

STG 09 > access permission: 31347 > customization > …(Example: always red)

> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function A 17" > Adjust the value to "not active" (factory setting: ambient light 3)
> Channel "Luminaire16BLK SLB35BLK SL KC9 light function B 16" > Adapt value to "Ambient light 3" (factory setting: not active)

Trailer Hitch - Activation/Release (Retrofit)

Activate STG 19 > Installation list > "69 - Trailer".

STG 01 > Encoding > Byte 05 > Activate bit 4 ("Trailer installed")-does not always work if not accepted: skip

STG 03 > Adaptation > Channel "Carriage Stabilization" > Set value to "activated".

Set STG 10 > Coding > Byte 03 > Bit 0-1 to "01 Trailer Hitch installed (manually removable)".

Activate STG 13 > Coding > Byte 02 > Bit 3

Set STG A5 > Coding > Byte 16 > Bit 0-1 to "Trailer Hitch installed".

STG 69 > Coding > …

> Byte 01 > Set bit 0-7 to "01 Trailer Connector Diagnosis active".
> Byte 03 > Set bit 0-7 to the appropriate entry (see retrofit instructions)

STG 09 > Coding > Byte 01 > Activate bit 1 ("Trailer Hitch Control Module installed")

or (if STG 09 without coding)

STG 09 > Access authorization: 31347 > Adaptation > "Network trailer connection device" channel > Set value to "installed".

If the front/forefield camera is installed, it will probably also have to be coded/adapted.

© 2013-2020 Daniel Fuchs page 16

Trailer maneuvering assistant (Trailer Assist) - activation/activation

RFK High or Area View (STG 6C) is required.

Note: The adjustments in the STG 5F are only to be carried out if problems arise when displaying the image in the infotainment system (e.g. no image, only image with a
trailer, etc.).

Activate STG 10 > Coding > Byte 00 > Bit 3

Activate STG 17 > Coding > Byte 12 > Bit 5

Activate STG 6C > Coding > Byte 10 > Bit 3

STG 5F > Customization > …

> Channel "Car_Function_Adaptations_Gen2-menu_display_trailer_assistant_after_disclaimer" > Set value to "activated".

> Channel "Car_Function_Adaptations_Gen2-menu_display_trailer_assistant_over_threshold_high" > Set value to "activated".
> Channel "Car_Function_List_BAP_Gen2-Trailer_Assistant_0x36" > Set value to "activated".
> Channel "Car_Function_List_BAP_Gen2-Trailer_Assistant_msg_bus_0x36" > Set value to "terminal 15".

Assistant light function - change light sensor sensitivity

STG 09 > Access authorization: 31347 > Adaptation > "Assistance light functions - light sensor sensitivity" channel > Adapt value (factory setting: normal)

Disable exhaust flap control

Deactivate STG 01 > Coding > Byte 09 > Bit 2

Auto Hold - Customization of dynamic hold assist

STG 03 > Adaptation > "Dynamic traction assistant" channel > Adjust value

"Early" > Brake releases quickly and with little gas (hardly or not at all perceptible, no jerk)
"Normal" > Factory setting (jerk noticeable)
"Late" > Brake releases late and only with a relatively large amount of gas (strong jerk)

The factory setting "Normal" can be particularly annoying when manoeuvring, as you have to accelerate a little more before the brakes release. This can also
be critical, especially in tight parking spaces, because the car jumps forward. The "Early" setting is ideal if you want to use Auto Hold!

© 2013-2020 Daniel Fuchs page 17

Auto Hold - state after restart

STG 03 > Adaptation > "Auto Hold Health" channel > Adjust value

"Last setting" > factory setting, active/inactive is controlled via button in the center console "Never
active" > Auto hold always disabled after ignition change
"Always active" > Auto hold always activated after ignition change

Auto-Lock also locks the gas cap

STG 09 > Access authorization: 31347 > Adaptation > Channel "Access control-speed-dependent tank lid locking" > Set value to "active".

Teach battery after change

STG 19 > Adjustment > "Battery adjustment" channels > Set values according to the installation

Front passenger airbag - deactivate button

STG 15 > Access authorization: 20103 > Adaptation > Channel "Airbag adaptations key switch" > Set value to "not parameterized".

Hill Start Assist - activation of the HHC

STG 03 > Coding > …

> Byte 25 > Activate bit 0

> Byte 25 > Activate bit 1 (not with all-wheel drive)

Hill Start Assist - set hold time

STG 03 > Adaptation > "Hill Start Assist" channel > Adjust value

"Early" > Brake releases quickly and with little gas (hardly or not at all perceptible, no jerk)
"Normal" > Factory setting (jerk noticeable)
"Late" > Brake releases late and only with a relatively large amount of gas (strong jerk)

© 2013-2020 Daniel Fuchs page 18

Rear turn signals active when tailgate is open

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire18BLK HLA60 light function C 18" > Set value to "Open trunk lid".
> Channel "Luminaire18BLK HLA60 dimming value CD 18" > Set percentage as desired (factory setting: 0)
> Channel "Luminaire19BLK HRC31 light function C 19" > Set value to "Open trunk lid".
> Channel "Luminaire19BLK HRC31 dimming value CD 19" > Set percentage as desired (factory setting: 0)

Adjust brake disc drying

STG 03 > Access authorization: 40304 > Adaptation > "Brake disc drying" channel > Adjust value ("not activated", "weak", "medium", "strong")

Coming Home/Leaving Home - Emulation via indoor light

If the vehicle does not have a coming home/leaving home, this can be emulated using the interior light function. To do this, the light function must be
assigned to the corresponding lights. Attention: The lights can deviate, here using the example of a Golf 7.

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire4TFL LB4 light function E 4" > Set value to "Interior light".
> Channel "Luminaire4TFL LB4 dimming value EF 4" > Set value to "100".
> Channel "Light 5 DRL RB32 light function E 5" > Set value to "Interior light".
> Channel "Luminaire5 DRL RB32 dimming value EF 5" > Set value to "100".
> Channel "Luminaire2SL VLB10 light function E 2" > Set value to "Interior light".
> Channel "Luminaire2SL VLB10 dimming value EF 2" > Set value to "26".
> Channel "Luminaire3SL VRB21 light function E 3" > Set value to "Interior light".
> Channel "Luminaire3SL VRB21 dimming value EF 3" > Set value to "26".
> Channel "Luminaire20BR LA71 light function F 20" > Set value to "Interior light".
> Channel "Luminaire21BR RC8 light function F 21" > Set value to "Interior light".
> Channel "Luminaire23SL HLC10 light function D 23" > Set value to "Interior light".
> Channel "Luminaire24SL HRA65 light function D 24" > Set value to "Interior light".
> Channel "Luminaire25KZL HA59 light function C 25" > Set value to "Interior light".
> Channel "Luminaire25KZL HA59 dimming value CD 25" > Set value to "100".

© 2013-2020 Daniel Fuchs page 19

Coming Home/Leaving Home - set the light duration to >30 seconds

STG 09 > access permission: 31347 > customization > …

> "Comfort lighting - Coming home menu setting" channel > Adjust value in seconds (value range: 0-90)
> Channel "Comfort lighting menu setting Leaving Home time per BAP" > Adjust value in seconds (value range: 0-90)

Coming Home/Leaving Home without low beam (only daytime running lights or parking lights)

STG 09 > access permission: 31347 > customization > …

> Channel "Comfort lighting - Coming Home lights" > Set value to "Low beam".
> Channel "Luminaire6ABL LC5 light function C 6" > Set value to "not active" (factory setting: Coming Home or Leaving Home active)
> Channel "Luminaire7ABL RB1 light function C 7" > Set value to "not active" (factory setting: Coming Home or Leaving Home active)
> Channel "Luminaire6ABL LC5-Dimming Direction CD 6" > Set value to "minimize".
> Channel "Luminaire7ABL RB1-Dimming Direction CD 7" > Set value to "minimize".

Coming Home/Leaving Home via fog lights

STG 09 > Access authorization: 31347 > Adaptation > Channel "Comfort lighting - Coming Home lights" > Set value to "Fog light".

Coming Home/Leaving Home - daytime running lights at full strength

(Skoda Octavia 3 5E)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire2SL VLB10 dimming value CD 2" > Set value to "100".
> Channel "Luminaire3SL VRB21 dimming value CD 3" > Set value to "100".

(VW Golf 7 AU etc.)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire2SL VLB10 light function B 2" > Set value to "Coming Home or Leaving Home active".
> Channel "Luminaire3SL VRB21 light function B 3" > Set value to "Coming Home or Leaving Home active".

© 2013-2020 Daniel Fuchs page 20

Customize Coming Home power-on trigger

STG 09 > Access authorization: 31347 > Adaptation > "Comfort lighting-coming-home switch-on event" channel > Adapt value

Coming home function automatically

STG 09 > Access authorization: 31347 > Adaptation > "Comfort lighting - Coming Home installation status" channel > Set value to "automatic".

Discover Media/Pro - Current location in header instead of selected driving profile

From model year 2016 (MIB2), the coding deactivates the MODE button and is therefore useless there.

STG 5F > Customization > …

> Channel "Vehicle menu operation-menu_display_charisma" > Set value to "not active".
> Channel "Vehicle menu operation-menu_display_charisma_clamp_15_off" > Set value to "not active".
> Channel "Vehicle menu operation-menu_display_charisma_over_threshold_high " > Set value to "not active".
> Channel "Vehicle menu operation-menu_display_charisma_standstill" > Set value to "not active".
> Channel "Vehicle menu operation-menu_display_charisma_after_disclaimer" > Set value to "not active".

Discover Media/Pro - Enable off-road ads (MIB 2)

STG 5F > Customization > …

> Channel "Car_Function_Adaptations_Gen2-menu_display_compass" > Set value to "active".

> Channel "Car_Function_Adaptations_Gen2-menu_display_compass_over_threshold_high" > Set value to "active".
> Channel "Car_Function_List_BAP_Gen2-compass_0x15" > Set value to "active".

Discover Media/Pro - Enable Online Services (MIB 2)

Requires a software version >200. After coding, the radio must be restarted (press and hold the power button for 10 seconds). The "Online
Services" can then be activated under Navigation > Settings.

STG 5F > Customization > …

© 2013-2020 Daniel Fuchs page 21

 > Channel "Traffic Information (TMC)" > Value around "32768"increase
> Channel "Menu entries for mobile online services" > Set value to "activated".
> Channel "Vehicle configuration online_POI" > Set value to "on".
> Channel "Vehicle configuration online_navigation" > Set value to "on".
> Channel "Vehicle configuration-online_street_view" > Set value to "on".

Discover Media/Pro - Enable Wi-Fi Streaming (MIB2)

STG 5F > Customization > Channel "WLAN" > Change value to "active".

Discover Media/Pro - Allow second phone over Bluetooth

STG 5F > Customization > Channel "Vehicle configuration-Support_second_phone" > Change value to "on".

Discover Pro - Change boot animation

STG 5F > Coding > Byte 18 > Adapt the value as a hexadecimal number accordingly

00 high line
01 Hybrid
02 GTD
03 GTI
04 BlueMotion
05 E-Golf
06 R line
07 R

Activate Discover Pro - Green Menu

STG 5F > Customization > Channel "Developer Mode" > set value to "enabled".

© 2013-2020 Daniel Fuchs page 22

Discover Pro - Show speed limit from map data
Activate STG 5F > Coding > Byte 24 > Bit 6

This coding only makes sense if traffic sign recognition (VZE) is not installed. The "Show traffic signs" setting must be activated in the map
settings.

Discover Pro - Disable radio modulation AM

Activate STG 5F > Coding > Byte 14 > Bit 1

Discover Pro - Change skin

STG 05 > Coding > Byte 17 > Adapt the value as a hexadecimal number accordingly

01 high line
02 GTI/GTD/R

Discover Pro - Enable Wi-Fi Streaming (MIB 1)

STG 5F > Coding > …

> Byte 15 > Activate bit 4

> Byte 24 > Activate bit 3

STG 5F > Customization > …

> Channel "WLAN" > Set value to "active".

> Channel "Vehicle Configuration-WIFI_Hotspot" > Set value to "active".
> Channel "Vehicle configuration UPnP" > Set value to "active".

Third brake light as a receipt for the central locking

STG 09 > access permission: 31347 > customization > …

© 2013-2020 Daniel Fuchs page 23

 > Channel "Dynamic flashing modes-ZV_Blinken_zu" > Set value to "active".
> Channel "Dynamic flashing mode ZV_Blinken_auf" > Set value to "active".
> Channel "Luminaire22BR MA57 light function B 22" > Value to "Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"

Third brake light active when tailgate is open

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire22BR MA57 light function C 22" > Set value to "Open trunk lid".
> Channel "Luminaire22BR MA57 dimming value CD 22" > Set value to "100".

The third brake light also flashes when the hazard warning lights are active

STG 09 > Access Permission 31347 > Customization > ...

> Channel "Dynamic flashing modes-Warnblinken_Zundung_EIN" > Set value to "active".

> Channel "Dynamic flashing modes-Warnblinken_Zundung_AUS" > Set value to "active".
> Channel "Luminaire22BR MA57 light function B 22" > Value to "Active flashing function has an assigned bit set to 1 in pa_dynamisch_blinken"
> Channel "Luminaire22BR MA57 light function C 22" > Set value to "Flash left dark phase".
> Channel "Luminaire22BR MA57 light function D 22" > Set value to "Flashing right dark phase".
> Channel "Luminaire22BR MA57-Dimming Direction CD 22" > Set value to "minimize".
> Channel "Luminaire22BR MA57 light function E 22" > Set value to "brake light".
> Channel "Luminaire22BR MA57 dimming value EF 22" > Set value to "100".

DWA - activation / activation (retrofitting)

These instructions apply to vehicles with coding in the BCM. Among them are most of the models introduced up to 2015.

STG 09 > Coding > …

> Byte 11 > Activate bit 7

> Byte 12 > Activate bits 0, 4, 5 and 7

© 2013-2020 Daniel Fuchs page 24

DWA - activation of the horn acknowledgment when locking and unlocking the vehicle

STG 09 > access permission: 31347 > customization > …

> "Release feedback signals-acoustic feedback" channel > Set value to "yes".
> Channel "Feedback signals - lock acoustic feedback" > Set value to "yes".
> Channel "Response signals menu control acoustic feedback" > Set value to "active".
> Channel "Response signals - global acoustic feedback" > Set value to "active".
> Channel "Feedback signals - acoustic feedback signal horn" > Set value to "active".

as needed too

> Channel "Feedback signal duration of the acoustic feedback from the single horn" > Set the value to "normal" or "short".

DWA - Start of the alarm on mechanical opening (Thatcham)

Activate STG 09 > Coding > Byte 12 > Bit 6

Dynamic high beam (DLA) - activation (until MY 2016)

Set STG 09 > Coding > Byte 02 > Bit 0-2 to "06 extended_high beam control,AFS: FLA: high beam (GLW:MDF)".

STG 09 > access permission: 31347 > customization > …

> Channel "High beam_Assistant assistance driving light: Sensitivity adjustable via BAP" > Change value to "available".
> Channel "High beam assistant menu control high beam assistant" > Change value to "present".
> Channel "High beam assistant menu control high beam assistant factory setting" > Change value to "available".

STG A5 > Coding > …

> Byte 19 > Set bit 0-3 to "00 Additional high beam not installed".
> Byte 19 > Set bit 4-7 to "30 Headlight version (for FLA): LED with var. light distribution".
> Byte 21 > Set bit 5-7 to "40 Dynamic Light Assistant (DLA)".

Activate STG 55 > Coding > Byte 04 > Bit 6 ("Masked permanent driving light (MDF) active/activated")

© 2013-2020 Daniel Fuchs page 25

Dynamic high beam (DLA) - activation (from MY 2017)

STG 09 > access permission: 31347 > customization > …

> Channel "Fernlicht_Assistent-Extended high beam control" > Change value to "AFS: FLA: High beam (GLW:MDF)".
> Channel "High beam_Assistant assistance driving light: Sensitivity adjustable via BAP" > Change value to "available".
> Channel "High beam assistant menu control high beam assistant" > Change value to "present".
> Channel "High beam assistant menu control high beam assistant factory setting" > Change value to "available".

STG A5 > Coding > …

> Byte 19 > Set bit 0-3 to "00 Additional high beam not installed".
> Byte 19 > Set bit 4-7 to "30 Headlight version (for FLA): LED with var. light distribution".
> Byte 21 > Set bit 5-7 to "40 Dynamic Light Assistant (DLA)".

STG 4B > Coding > …

> Byte 10 > Activate bit 6 ("Masked continuous driving light (MDF) active/activated")
> Byte 10 > Activate bit 7 ("Sliding headlight range control (GLW) active/activated")
> Byte 08 > Activate bit 1 (if error occurs in MFA)
> Byte 09 > Activate bit 4 (if error occurs in MFA)

After the coding has been completed, a basic setting of the headlights must be carried out.

Park Assist - Change Shutdown Speed

STG 10 > Adaptation > "Switch-off speed for parking aid" channel > Set value in km/h (factory setting: 15 km/h; value range: 1 to 15)

Parking Assist - Disable activation sound

STG 10 > Customization > Channel "Park Assist Activation Sound" > Set value to "disabled".

Parking Assist - Disable Audio Attenuation

STG 10 > Customization > Audio Reduction Request Channel > Set Value to Disabled

© 2013-2020 Daniel Fuchs page 26

Parking assistance - automatic activation when driving slowly forward

Activate STG 10 > access authorization: 71679 > coding > byte 03 > bit 4

Park Assist - Adjust Curb Distance (Trigger Continuous Tone/Last Stage)

STG 10 > Adaptation > "Distance to curb" channel > Adjust value in cm (factory setting: 15)

Parking aid - activate display, despite small parking aid (Leon III 5F, Audi A3 8V)

STG 10 > Access authorization: 71679 > Encoding > Byte 02 > Activate bit 0 ("Optical display parking aid (OPS) active")

Parking aid - activate/deactivate guides

STG 10 > access authorization: 71679 > coding > byte 01 > bit 5 (de)activate ("Vehicle Path Display active/enabled")

Parking Aid - adjust front/rear volume

STG 10 > Customization > …

> Channel "Loudspeaker volume for front parking aid" > Adjust value accordingly (factory setting: 3)
> Channel "Loudspeaker volume for rear parking aid" > Adjust value accordingly (factory setting: 6)

Parking Aid - Front/Rear Pitch Adjust

STG 10 > Customization > …

> Channel "Frequency speaker for front parking aid" > Adjust value accordingly (factory setting: 6)
> Channel "Frequency speaker for rear parking aid" > Adjust value accordingly (factory setting: 3)

Electronic Parking Brake (EPB) - deactivation of automatic activation when seat belt is unbuckled

STG 03 > Access authorization: 37202 > Adaptation > "Belt lock query" channel > Set value to "not active".

© 2013-2020 Daniel Fuchs page 27

ESP - Change available modes (ASR off / ESC Sport / ESC off)

STG 03 > Coding > Byte 29 > Adapt the value as a hexadecimal number accordingly

?6 ESC on / ESC Sport / ESC off

?7 ESC on / ASR off / ESC off
?9 ESC on / ASR off / ESP Sport

Activate driving school mode (display of speed and indicators on the radio, only possible with Composition Colour/Touch and Discover Media)

STG 5F > Customization > …

> Channel "Vehicle function list CAN-driving school" > Set value to "available".
> Channel "Vehicle Menu Operation-menu_display_driving_school" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_driving_school_over_threshold_high" > Set value to "activated".

Window operation - do not cancel release run-on when opening the door

STG 09 > Access authorization: 31347 > Adaptation > Channel "Cancel access control 2 release run-on FH when door is opened" > Set value to "not active".

High-beam assistant (Light Assist/HBA) - activation (variant 1)

Caution: Multifunction camera (control unit A5) must be installed, e.g. E.g. when ordering with Lane Assist and/or VZE installed! After successful coding,
you should wait for the bus to stop. Also check variant 2, these may have to be mixed, e.g. Passat B8 up to MY2016 requires coding in the STG A5 of
variant 2.

STG 09 > Access authorization: 31347 > Adaptation > Channel "Assistance light functions menu control high beam assistant" > Set value to "present".

Set STG 09 > Coding > Byte 02 > Bit 0-2 to "03 Bi-Xenon headlights with Light Assist".

Set STG A5 > Coding > Byte 02 > Bit 0-7 to "01 coding_Light_Assist High_Beam_Assist".

© 2013-2020 Daniel Fuchs page 28

High-beam assistant (Light Assist/HBA) - activation (variant 2)

Caution: Multifunction camera (control unit A5) must be installed, e.g. E.g. when ordering with Lane Assist and/or VZE installed! After successful coding, you
should wait for the bus to stop. In the "Extended high beam control" channel, the correct value must be selected according to the previous configuration: if the
high beam is controlled via AFS, this must also be selected in the new value. The existing value is only extended by the "FLA".

STG 09 > access permission: 31347 > customization > …

> Channel "High beam assistant menu control high beam assistant" > Set value to "present".
> Channel "High beam_assistant menu control high beam assistant factory setting" > Set value to "present".
> Channel "Highlight_Assistant-Extended_HighlightControl" > Set value to "AFS: FLA: BCM high beam" or "AFS: FLA: High beam via AFS".

Set STG A5 > Coding > Byte 21 > Bit 5-7 to "20 AFS_coding_Light_Assist,High_Beam_Assist".

High-beam assistant (Light Assist) - adjust switch-on and switch-off times

STG A5 > Access Permission: 20103 > Customization > …

> "Activation speed for high-beam assistant" channel > Adjust value in km/h (factory setting: 57)
> "Speed threshold for high beam recommendation" channel > Adjust value in km/h (factory setting: 27)

High beam assistant (Light Assist) - disable reset

STG 09 > Access authorization: 31347 > Adaptation > Channel "Assistance light functions - high beam assistant reset" > Set value to "not
active" (factory setting: active; the FLA is therefore deactivated again with every ignition off)

High beam assistant (Light Assist) - deactivate city recognition

STG A5 > Access Permission: 20103 > Customization > Channel "Main_Beam_Assist_Urban_Area_Detection" > Change value to "not active".

Recalibrate the front/forefield camera after lowering

STG A5 > Access Permission: 20103 > Customization > …

© 2013-2020 Daniel Fuchs page 29

 > "Body height, front left wheel arch edge" channel > Correct the value
> Channel "Body height, wheelhouse edge, front right" > Correct the value
> "Body height, rear left wheel arch edge" channel > Correct the value
> "Body height, rear right wheel arch edge" channel > Correct the value

Activate Front Assist - Prewarning - Early/Medium/Late selection

An ACC control unit with part number 3Q0 or 2Q0 is required.

STG 13 > Coding > Byte 11 > Disable bit 3 ("adjustability_awv_pre_warning")

Front Assist - pre-warning - save selected value

An ACC control unit with part number 3Q0 or 2Q0 is required.

STG 13 > Encoding > Byte 11 > Activate bit 4 ("default_value_awv_pre_warning")

Windshield Wiper - Park when hood is opened

STG 09 > Access authorization: 31347 > Adaptation > Channel "Park windscreen wiper wiper when opening the hood" > Set value to "active".

Windscreen wiper - parking when ignition is switched off (Octavia III 5E)

Deactivate STG 09 > coding > wiper (WWS) > byte 01 > bit 4

Windscreen wipers - set the service position via the menu (Audi A3 8V)

STG 09 > Access authorization: 31347 > Adaptation > Channel "Windscreen wiper menu control front wiper" > Set value to "active".

STG 5F > Customization > …

> Channel "Vehicle function list BAP-wiper_comfort_0x0C" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_wiper" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_wiper_over_threshold_high" > Set value to "activated".

© 2013-2020 Daniel Fuchs page 30

Windscreen wipers - activate teardrop wipers

STG 09 > Access Permission: 31347 > Customization > Windshield Wiper Teardrop Front Status Channel > Change Value to Active

Windscreen wipers - Adjust wipe cycles per minute

STG 09 > access permission: 31347 > customization > …

> Channel "Wiping speeds - continuous wiping level 1 cycles per minute" > Adjust value (factory setting: 40)
> Channel "Wiping speeds - continuous wiping level 2 cycles per minute" > Adjust value (factory setting: 60)
> Channel "Wiping speeds - Reduced wiping speed cycles per minute" > Adjust value (factory setting: 30)

Windscreen wipers - activate teardrop wipers in front

Activate STG 09 > Coding > WWS > Byte 02 > Bit 5

STG 09 > Access permission: 31347 > Adaptation > Channel "Windscreen wiper teardrop front status" > Set value to "active".

Window regulator overrun release after ignition off

STG 09 > Access authorization: 31347 > Adaptation > Channel "Access control 2-FH SAD Kl15Aus release time" > Adapt value (factory setting: 600 s)

Footwell lighting - activation/activation (retrofit)

STG 09 > Coding > …

> Byte 05 > Activate bit 7

> Byte 17 > Activate bit 3

STG 09 > access permission: 31347 > customization > …

> Channel "Interior lighting - menu control, ambient lighting, effect lighting" > Change the value to "active".
> Channel "Luminaire30FR LC72 load type 30" > Change value to "36 - LED low power" (for LED) or "18 - 2* 5W" (for incandescent lamps).
> Channel "Light30FR LC72 light function A 30" > Change value to "footwell light".
> Channel "Luminaire30FR LC72 dimming value AB 30" > Change value to "100".

© 2013-2020 Daniel Fuchs page 31

Footwell lighting - activation/release multicolored (retrofit)
STG 09 > access permission: 31347 > customization > …

> Channel "ambient_lighting_lin_slaves_modules-pa_verbauinfo_slave_14" > Change value to "installed".

> Channel "ambient_lighting_lin_slaves_groups-pa_verbauinfo_gruppe_14" > Change value to "3_not_defined".
> Channel "Luminaire30FR LC72 load type 30" > Change value to "general LED up to 12W".
> Channel "Light30FR LC72 light function A 30" > Change value to "footwell light".
> Channel "Luminaire30FR LC72 dimming value AB 30" > Change value to "127".

Footwell lighting - activate the ambient lighting function (Audi)

After coding

STG 09 > access permission: 31347 > customization > …

> Channel "Interior light lamp configuration - footwell lighting" > Change value to "installed".
> Channel "Interior light 2nd generation default value ambience profile footwell" > Change value to "20%".

Footwell lighting - conversion to LED - prevent error messages in the BCM

STG 09 > Access authorization: 31347 > Adaptation > Channel "Luminaire30FR LC72 load type 30" > Set value to "32 - general LED up to 12W" (factory setting: 18 - 2* 5W)

Disable yellow mode switch light

With this coding, the switch for driving profile selection remains in the basic color in every mode and does not change to yellow.

Activate STG 09 > Coding > Byte 15 > Bit 7

Activate trailer stabilization

STG 03 > Adaptation > Channel "Carriage Stabilization" > Set value to "activated".

© 2013-2020 Daniel Fuchs page 32

Transmission - disable freewheel

Deactivate STG 19 > Coding > Byte 12 > Bit 2

Tailgate (electric) - also open/close while driving

STG 6D > Access authorization: 12345 > Adaptation > "Speed threshold for "vehicle moving"" channel > Adapt value in km/h (factory setting: 6)

Tailgate (electric) - open/close when towing a trailer

STG 6D > Access authorization: 12345 > Adaptation > "Open when trailer is detected" channel > Value to "activated" (factory setting: not activated)

Tailgate (electric) - open/close via button in the center console and FFB

STG 6D > Access Permission: 12345 > Customization > …

> Channel "Activation by switch for tailgate remote unlocking - one-touch function when closing" > Set value to "active".
> Channel "Activation by button for tailgate opening radio key tip function when closing" > Set value to "active".

or
> Channel "Activation by switch for tailgate remote unlocking button function when closing" > Set value to "active".
> Channel "Activation by button for tailgate opening radio key button function when closing" > Set value to "active".

The tactile function is the long press of the button, while the tap function is the short press.

Tailgate (electric) - change opening height

STG 6D > Access authorization: 12345 > Adaptation > "Program opening stop" channel > Adapt value

Tailgate (electric) - Monitoring for keys in the trunk (KESSY)

STG 6D > Access Permission: 12345 > Customization > …

© 2013-2020 Daniel Fuchs page 33

 > Channel "Key in trunk monitoring" > Set value to "active".
> Channel "Warning tone for key in trunk" > Set value to "active".
> Channel "Behaviour with key in trunk during closing" > Set value to "open".

Tailgate (electric) - Do not stop closing when leaving the close range
STG 6D > Access authorization: 12345 > Adaptation > Channel "Close with FFB, end when leaving close range" > Adjust value

Tailgate (electric) - allow closing with the key from a greater distance
STG 09 > Access authorization: 31347 > Adaptation > Channel "close top operation range limitation for servo tail" > Set value to "not active".

Tailgate (Electric) - Customize or disable warning signals

STG 6D > Access Permission: 12345 > Customization > …

> Channel "pitch of the acoustic warning" > Adjust value in Hz as desired (factory setting: 1000)
> Channel "Volume of the acoustic warning" > Adjust the value to "not activated" (factory setting: activated)

and or

> Channel "Warning signal when closing with button in the interior or via radio key" > Set value "not activated".
> Channel "Warning signal when opening with button in the interior or via radio key" > set value "not activated".

Close tailgate after individual opening with a time delay (30 seconds)

STG 09 > Access authorization: 31347 > Adaptation > Channel "Access control release run-on rear after individual opening via HDF radio button" > Set value to
"active" (factory setting: not active)

Tailgate lights remain on when the lid is opened (Golf 7 AU, Audi A3 8V)
STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire27NSL RC6 light control HD AB 27" > Change value to "Always" (factory setting: only_if_closed)
> Channel "Luminaire26NSL LA72 light control HD AB 26" > Change value to "Always" (factory setting: only_if_closed)
© 2013-2020 Daniel Fuchs page 34
Heated rear window - adjust heating duration

STG 09 > Access authorization: 31347 > Adaptation > Channel "window heating/rear window heating time value" > Adapt value in seconds (factory setting: 600)

Disable rear wiper

Deactivate STG 09 > Coding > Byte 13 > Bit 2

Deactivate STG 16 > Coding > Byte 00 > Bit 2

Rear wiper - activate automatically when the front wiper is active at level 2 or higher

STG 09 > Access authorization: 31347 > Adaptation > "Rear window wiper automatic rear wipe" channel > Change value to "active".

Rear wiper - disable automatic wiping when reverse gear is engaged

STG 09 > Access authorization: 31347 > Adaptation > Channel "Rear window wiper comfort wipe rear" > Change value to "not active".

Rear wiper - Activate tear wipe

STG 09 > Access permission: 31347 > Adaptation > Channel "Rear window wiper teardrop rear" > Change value to "active".

Rear wiper - Adjust the wipe interval of the wiper

STG 09 > access permission: 31347 > customization > …

> Channel "Rear window wiper comfort wipe rear interval pause time level interval)" > Adjust value (factory setting: 7, maximum: 14)
> Channel "Rear window wiper comfort wipe, rear Interval pause time, automatic level)" > Adjust value (factory setting: 7, maximum: 14)

HUD - Move display horizontally

STG 82 > Adjustment > "Image Shift-Horizontal Shift" channel > adjust value (positive = further right, negative = further left)

© 2013-2020 Daniel Fuchs page 35

HUD - Move display vertically
STG 82 > Adjustment > "Image Shift-Vertical Shift" channel > Adjust value (positive = higher, negative = lower)

Infotainment - Activate Apple Wireless Carplay (Audi)

In principle, Carplay must be available for activation. In addition, the infotainment system must have a WLAN function.

STF 5F > Customization > …

> Channel "Vehicle Configuration-Apple_DIO_Wireless" > Change value to "on".

> Channel "Vehicle configuration-wlan_5ghz_switch" > Change value to "activated".

Infotainment - Remove or activate chute lock

STG 5F > Adaptation > Channel "Eject lock" / "Button for CD return" > Change the value accordingly

Infotainment - activate welcome sound (Audi)

STG 5F > Adaptation > Channel "Vehicle configuration-vehicle_readiness_sound" > Change value to "activated".

License plate light - conversion to LED

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire25KZL HA59 load type 25" > Change value to "43 - general LED".
> Channel "Luminaire25KZL HA59 dimming value AB 25" > Change value to "127".

KESSY - Automatic locking when the doors are closed (3Q0 control unit)

If the adjustment channel is not available, it should be left out.

Activate STG 05 > Coding > Byte 02 > Bit 5

STG 05 > Customization > Channel "internal_passive_entry_exit_byte1-passive_exit_door_slam_lock" > Set value to "active".

© 2013-2020 Daniel Fuchs page 36

KESSY - Automatic locking when the doors are closed (5Q0 control unit)

The automatic mirror folding does not work in this way. The fuel filler flap is also not locked. If the adjustment channel is not available, it should
be left out.

Activate STG 05 > Coding > Byte 02 > Bit 4

STG 05 > Customization > Channel "internal_passive_entry_exit_byte1-passive_exit_door_slam_lock" > Set value to "active".

KESSY - Activate staging/pulsing of the start button

STG 05 > Customization > …

> Channel "DeveloperCoding: Search lights-ZAT_illumination_concept_mybeat_clamp58xt" > Change value to "activated".

> Channel "DeveloperCoding: Search lights-ZAT_illumination_modus_mybeat_clamp58xt" > Change value to "activated".

KESSY - activate convenience opening

In order to carry out the convenience opening via KESSY, both door sensors (open & close) must be held at the same time.

STG 09 > Access authorization: 31347 > Adaptation > Channel "Open access control 2-Kessy comfort" > Change value to "active".

KESSY - Temporary deactivation - activation (3Q0 control unit)

The KESSY control unit with at least index G (SW 0906) is required for this coding. The control unit can, if the software version is too old, with VCP or similar. be
updated. If an update is necessary, all adjustments to the control unit must first be backed up and imported again after the flash. The channels "Tailgate
opening control unit: Sensor 2: Control parameters" and "Tailgate opening control unit: Vehicle type" are particularly important.

STG 05 > Customization > …

> Channel "internal_passive_entry_exit_byte2-lf_shutdown" > Set value to "activated".

> Channel "lf_shutdown_timeout_2nd_operation" > Set value to "5" (or desired timeout)

© 2013-2020 Daniel Fuchs page 37

KESSY - Temporary deactivation - activation (5Q0 control unit)

The KESSY control device with at least index C (SW 0803) is required for this coding. The control unit can, if the software version is too old, with VCP or
similar. be updated.

STG 05 > Customization > …

> Channel "DeveloperCoding: Passive Entry Exit (Byte 2)-lf_shutdown" > Set value to "activated".
> Channel "lf_shutdown_timeout_2nd_operation" > Set value to "5" (or desired timeout)

KESSY - Deactivate door sensors

Deactivate STG 05 > Coding > Byte 00 > Bit 0 and 1

KESSY - Activate locking via Easy Close (3Q0 control unit)

After this coding, it is possible to lock the vehicle using the Easy Close. Locking via the door sensor is then not separately necessary.

STG 05 > Adaptation > Channel "Byte9_VIP-Coding_easyclose_locking" > Set value to "activated".

Air Conditioning - Air Care - Activation

The prerequisite is that the hypoallergenic cabin air filter (5Q0819669) has been installed. The climate control unit requires at least SW 1401 (perform an
update if necessary) and an MIB2 infotainment system must be installed. The gateway requires at least SW 1244 or 2244.

Activate STG 08 > coding > byte 15 > bit 5 ("recirculation air filtering")

Air Conditioning - Air Care - Save Condition

STG 08 > Adaptation > Channel "Interior air filtering: Save" > Set value to "active".

Air conditioning - adjust the sensitivity of the interior humidity sensor

Adapt STG 08 > Coding > Byte 14 > Bit 2-3

© 2013-2020 Daniel Fuchs page 38

Air conditioning - show blower level also in AUTO mode (not Audi A3 8V)

Activate STG 08 > Coding > Byte 11 > Bit 6 ("Blower Status Display in AUTO-mode active")

Air Conditioner - Change the brightness of the LCD temperature display

STG 08 > Customization > Channels "dimming_characteristics_2 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value, or replicate the curve.

Air conditioning - Brightness LEDs for current fan level

STG 08 > Customization > Channels "dimming_characteristics_3 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value, or replicate the curve.

Air conditioning - Brightness LEDs for heated seats

STG 08 > Customization > Channels "dimming_characteristics_4 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value, or replicate the curve.

Air conditioning - brightness LEDs (rest)

STG 08 > Customization > Channels "dimming_characteristics_5 Y?" > Adjust values in percent

All Y values must be adjusted. These can all be set to one value, or replicate the curve

Air conditioning - enable fan speed offset logic

The change means that manual adjustment of the blower level continues to regulate in auto mode. The set level then remains permanently active beforehand.
This applies until the "AUTO" button is pressed again.

STG 08 > Adaptation > Channel "Fan logic with manual adjustment" > Set value to "Offset manual".

© 2013-2020 Daniel Fuchs page 39

Instrument cluster - disable seat belt reminder

STG 17 > Customization > Disable seat belt warning channel > Change value to yes

or
Deactivate STG 17 > Coding > Byte 00 > Bit 2

Instrument cluster - change reserve tank volume

STG 17 > Adaptation > Channel "defuel_threshold" > Adjust value in liters as desired

Instrument cluster - dial lighting also active with parking lights

STG 17 > Access permission: 25327 > Adaptation > Channel "Illumination_algorithm-Scale_switching_algorithm" > Set value to "lds" (factory setting:
parking_light)

Instrument cluster - change skin

STG 17 > Customization > Channel "Display" > Adjust value

Instrument cluster - change scale display (VC/AID/FPK)

STG 17 > Adjustment > "Tube display" channel > adjust value

Instrument cluster - Adjust speedometer maximum (VC/AID/FPK)

STG 17 > Adaptation > "Tachometer end value" channel > Adjust value

Instrument cluster - activate pointer test (staging).

STG 17 > Encoding > Byte 01 > Activate bit 0 ("pointer wipe active")

© 2013-2020 Daniel Fuchs page 40

Instrument Cluster - Ignition Active Adjust/deactivate message

STG 17 > Adaptation > Channel "Ignition active message; trigger" > Adjust value accordingly

"no ad" > Warning disabled

"Drivers door" > Warning message when driver's door is opened
"all doors" > Alert message when any door is opened

Convenience actions via FFB even while the ignition is on/the engine is running

STG 09 > Access authorization: 31347 > Adaptation > Channel "Access control radio at terminal 15 on" > Set value to "active".

Convenience turn signal Change flash cycle

STG 09 > Access authorization: 31347 > Adaptation > Channel "Indicator control - convenience flashing flashing cycles" > Set value (value range: 1-5)

Afterwards, the factory setting may have to be restored via the CAR menu, only then will the changed flashing cycle work!

Deactivate convenience turn signals

STG 09 > Access authorization: 31347 > Adaptation > Channel "Turn signal control - comfort flashing" > Set value to "not active".

Change steering characteristics without driving profile selection

STG 44 > Access authorization: 19249 > Adaptation > Channel "Characteristics of the steering support" > Change value accordingly

Heated steering wheel - Automatic activation

The function can then be activated/deactivated via the climate menu.

Set STG 08 > Coding > Byte 13 > Bit 2-3 to "08 Steering wheel heating, car mode, outside temperature".

© 2013-2020 Daniel Fuchs page 41

Adjust steering assistance

The adaptation only remains active until the next ignition change.

STG 44 > Access Permission: 19249 > Customization > "Steering Assist" Channel > Customize Value (100%, 80%, 60%, 40% or 20%)

Adapt steering support directly when changing driving profile (instead of incremental change)

STG 44 > Access authorization: 28183 > Adaptation > "Drive profile switchover" channel > Change value to "Direct" (factory setting: step by step: controlled via time)

Adjust light switch-on threshold (Leon III 5F)

See also the section "Assistance light function - change light sensor sensitivity"

STG 09 > Coding > RLS > Byte 00 > Adjust bit 3-5 ("light switch-on threshold")

Flashing headlights also activates fog lights

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire12NL LB45 light function C 12" > Change the value to "General headlight flasher".
> Channel "Luminaire12NL LB45 dimming value CD 12" > Change value to "127".
> Channel "Luminaire13NL RB5 light function C 13" > Change the value to "General headlight flasher".
> Channel "Luminaire13NL RB5 dimming value CD 13" > Change value to "127".

and if desired

> Channel "Luminaire12NL LB45 light function D 12" > Change value to "Left high beam".
> Channel "Luminaire13NL RB5 light function D 13" > Change value to "High beam right".

Headlight flash during the day via fog lights

STG 09 > access permission: 31347 > customization > …

© 2013-2020 Daniel Fuchs page 42

 > Channel "Luminaire12NL LB45 light function E 12" > Set value to "Headlight flasher with inactive low beam and inactive permanent headlights".
> Channel "Luminaire12NL LB45 dimming value EF 12" > Set value to "100".
> Channel "Luminaire13NL RB5 light function E 12" > Set the value to "Headlight flasher with inactive low beam and inactive permanent headlights".
> Channel "Luminaire13NL RB5 dimming value EF 12" > Set value to "100".
> Channel "Luminaire6ABL LC5 light function B 6" > Set the value to "Headlight flasher when low beam is already active or permanent driving light is already active".
> Channel "Luminaire7ABL RB1 light function B 7" > Set the value to "Headlight flasher when low beam is already active or permanent driving light is already active".

additionally for the Skoda Octavia III RS

> Channel "Luminaire8FL LB39 light function E 8" > Set value to "Headlight flasher with inactive low beam and inactive permanent headlights".
> Channel "Luminaire8FL LB39 dimming value EF 8" > Set value to "100".
> Channel "Luminaire9FL RB2 light function E 9" > Set the value to "Headlight flasher with inactive low beam and inactive permanent headlights".
> Channel "Luminaire9FL RB2 dimming value EF 9" > Set value to "100".

Headlight flash possible with ignition off

STG 09 > Access authorization: 31347 > Adaptation > Channel "Headlight and parking light headlight flasher possible with ignition off" > Set value to
"active" (factory setting: not active)

Light/rain sensor - activation/activation (retrofit)

STG 09 > Coding > …

> Byte 06 > Set bit 0-1 to 02

> Byte 07 > Activate bit 5

STG 09 > access permission: 31347 > customization > …

> "Comfort lighting - Coming Home installation status" channel > Set value to "automatic".
> Channel "Comfort lighting menu control Coming Home factory setting" > Set value to "active".
> Channel "Comfort lighting - menu setting coming home" > Set value to "30 s".
> Channel "Comfort lighting - Coming Home lights" > Set value to "Low beam".
> "Comfort lighting-coming-home switch-on event" channel > Set value to "Driver door".
> Channel "Comfort lighting - brightness threshold infrared measurement" > Value to "12 lx"or"3".

© 2013-2020 Daniel Fuchs page 43

 > "Comfort lighting-Leaving-Home installation status" channel > Set value to "released".
> Channel "Comfort lighting menu control Leaving-home activation via BAP" > Set value to "active".
> Channel "Comfort lighting menu setting Leaving-home time per BAP" > Set value to "30 s".
> Channel "Comfort lighting brightness threshold forward measurement" > Value to "46400 lx"or"112".

The adjustments must be checked and, if necessary, adjusted in order to ensure perfect functionality.

Light/rain sensor - activate rain closing

STG 09 > access permission: 31347 > customization > …

> Channel "Access control 2-Rainclosing_on_off" > Change the value to "active".
> Channel "Access control 2-Rainclosing_art" > Change the value to "Permanent".
> Channel "Access control 2 menu control rain closing" > Change the value to "active".

Activate STG 09 > Coding > RLFS > Byte 00 > (Bit 1 and) Bit 2

The coding of bit 2 is not accepted, it works with bit 1. The coding for the "RLHS" is not known.

MFA - adjust the display time for the rear seat belt display

STG 17 > Adaptation > Channel "time_parameter_display-hmi_t_FondGurt" > Adjust value in seconds

MFA - Customize service reminder display time

STG 17 > Adaptation > Channel "time_parameter_display-hmi_t_NextServiceAnz_ms" > Adjust value in seconds

MFA - Adjust display time for warning messages

STG 17 > Adaptation > Channel "time_parameter_display-hmi_t_NextWarning_ms " > Adapt value in seconds

MFA - briefly display the driving profile when changing

Activate STG 19 > Coding > Byte 08 > Bit 4

© 2013-2020 Daniel Fuchs page 44

MFA - Disable the message »Switch on low beam«

STG 09 > Access authorization: 31347 > Channel "External light_overarching-Fahrlichtwarning_Hinweis_Konfig" > Set value to "not active".

MFA - compass display at the bottom

Activate STG 17 > Coding > Byte 09 > Bit 3

MFA - Show volume to be refueled

Activate STG 17 > Coding > Byte 10 > Bit 4

Value deviates somewhat from the real amount of fuel to be refueled. Display in the MFA is in 5 l steps!

MFA - display oil temperature

Activate STG 17 > Coding > Byte 10 > Bit 1

MFA - Show lap counter/lap timer

Activate STG 17 > Coding > Byte 01 > Bit 3

MFA - Show shift recommendation (Audi A3 8V)

Activate STG 17 > coding > byte 01 > bit 5 ("switching recommendation (economy) active")

MFA - warning when driving with rear fog light

STG 09 > Access authorization: 31347 > Adaptation > "Headlights and parking lights/rear fog light warning speed" channel > Adapt value in km/h

At speeds above this value, a message is displayed in the MFA that the NSL should be switched off.

© 2013-2020 Daniel Fuchs page 45

MFA - warning when driving with active parking lights

STG 09 > Access authorization: 31347 > Adaptation > Channel "Headlights and parking lights warning drive with parking lights" > Change the value to "active".

MFA - warning at speeds above 120 km/h

Activate STG 17 > Coding > Byte 00 > Bit 6

Adjust/deactivate MFA - warning notice danger of ice

STG 17 > Access Permission: 20103 > Customization > …

> Channel "outside_temperature-p_ice_warning_exit_temperature" > Set value in °C (factory setting: 6)

> Channel "outside_temperature-p_ice_warning_entry_temperature" > Set value in °C (factory setting: 4)

MFA - warning of danger of slippery resubmission after engine off

STG 17 > access permission: 20103 > adjustment > channel "outside_temperature-p_storage_time_engine_off" > adjust value in minutes (factory setting: 180)

Show MFA - cylinder deactivation (ACT / COD).

STG 17 > Adaptation > "Cylinder deactivation" channel > Change value to "Display" (factory setting: No display)

Adjust microphone sensitivity

STG 5F > Adjustment > Microphone Sensitivity Channel > Adjust Value

Multifunction steering wheel - activation/activation (retrofit) (Audi A3 8V)

Activate STG 16 > Coding > Byte 00 > Bit 1 (does not have to be - try it out)

STG 17 > Coding > Byte 10 > Bit 7

© 2013-2020 Daniel Fuchs page 46

STG 19 > Coding > Byte 01 > Bit 0

STG 5F > Customization > …

> Channel "Vehicle function list CAN-MFL" > Set value to "available".
> Channel "Vehicle function list BAP-MFL_0x0F" > Set value to "activated".
> Channel "Vehicle function list BAP-MFL_Jocker_0x34" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_MFL_jocker" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_MFL_jocker_over_threshold_high" > Set value to "activated".

Fog Lights - Activation/Release (Retrofit)

Activate STG 09 > Coding > Byte 07 > Bit 3

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire12NL LB45 load type 12" > Set value to "10 - general headlights".
> Channel "Luminaire12NL LB45 lamp defect bit position 12" > Set value to "38".
> Channel "Luminaire12NL LB45 error location middle byte DTC-DFCC 12" > Set value to "22".
> Channel "Luminaire12NL LB45 light function A 12" > Set value to "Fog light left".
> Channel "Luminaire12NL LB45 light function B 12" > Set value to "Left cornering light".
> Channel "Luminaire12NL LB45 dimming value AB 12" > Set value to "100".
> Channel "Luminaire13NL RB5 load type 13" > Set value to "10 - general headlights".
> Channel "Luminaire13NL RB5 lamp defect bit position 13" > Set value to "42".
> Channel "Luminaire13NL RB5 error location middle byte DTC-DFCC 13" > Set value to "23".
> Channel "Luminaire13NL RB5 light function A 13" > Set value to "Right fog light".
> Channel "Light13NL RB5 light function B 13" > Set value to "Right cornering light".
> Channel "Luminaire13NL RB5 dimming value AB 13" > Set value to "100".

Fog lights - activate cornering lights

STG 09 > access permission: 31347 > customization > …

> Channel "Light12NL LB45 light function B 12" > Adjust the value to "Left cornering light".
> Channel "Light13NL RB5 light function B 13" > Adjust value to "Right cornering light".
> "Static cornering light regulation" channel > desiredregulation set
© 2013-2020 Daniel Fuchs page 47
Fog Lights - Unlock Crossing Lights
STG 55 > coding > …

> Byte 05 > Activate bit 0 (predictive route data, activated)

> Byte 05 > Activate bit 1 (intersection light with route data, activated)

or
STG 4B > Coding > …

> Byte 11 > Activate bit 0 (predictive route data enabled)

> Byte 11 > Activate bit 1 (intersection light activated with route data)

Fog lights - conversion to LED (Octavia III 5E)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire8FL LB39 load type 8" > Set value to "6 - LED light module".
> Channel "Luminaire9FL RB2 load type 9" > Set value to "6 - LED light module".
> Channel "Luminaire12NL LB45 load type 12" > Set value to "6 - LED light module".
> Channel "Luminaire13NL RB5 load type 13" > Set value to "6 - LED light module".

Rear fog lights - both active (Octavia III 5E)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire26NSL LA72 light function A 26" > Adjust the value to "rear fog light when no trailer is plugged in".
> Channel "Luminaire26NSL LA72 dimming value AB 26" > Set value to "100" if not already set
> Channel "Light27NSL RC6 light function A 27" > Adjust the value to "Rear fog light when no trailer is plugged in".
> Channel "Luminaire27NSL RC6 dimming value AB 27" > Set value to "100" if not already set

Personalization - Activation (Variant 1)

This variant applies to vehicles with coding in the BCM. Among them are most of the models introduced up to 2015. Control units that are not installed can
simply be left out.

© 2013-2020 Daniel Fuchs page 48

STG 09 > Coding > …

> Byte 08 > Activate bit 2 (Personalization profiles active)

> Byte 11 > Bit 4-6 to "10 Profile_Variant, Account (v. 1.x)"

STG 09 > access permission: 31347 > customization > …

> Channel "Personalization activation option_im_HMI-Menue_sichtbar" > Adjust value to "active".

> Channel "Personalization-Number_of_user_accounts" > Adjust value to "4".
> Channel "Personalization-User Account Management_in_HMI-Menu_visible" > Adjust value to "active".
> Channel "Personalization-Personalization_active" > Adjust value to "active".
> Channel "Personalization-Personalization-functions_in_HMI-Menue_visible" > Adjust the value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_0" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_1" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_2" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_3" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_4" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_5" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_6" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_7" > Adjust value to "active".

Activate STG 17 > Coding > Byte 10 > Bit 0

Set STG 08 > Coding > Byte 15 > Bit 3-4 to "08 Personalization, activated".

Set STG 36 > Coding > Byte 09 > Bit 1-2 to "02 Func_key_memory_personalization, personalization active".

Personalization - Activation (Variant 2)

This variant applies to vehicles without coding in the BCM. Among them are most models that were introduced from 2015 or have received a facelift. Control
units that are not installed can simply be left out.

STG 09 > access permission: 31347 > customization > …

> Channel "Personalization activation option_im_HMI-Menue_sichtbar" > Adjust value to "active".

> Channel "Personalization-Number_of_user_accounts" > Adjust value to "4".
> Channel "Personalization-User Account Management_in_HMI-Menu_visible" > Adjust value to "active".

© 2013-2020 Daniel Fuchs page 49

 > Channel "Personalization-Personalization_active" > Adjust value to "active".
> Channel "Personalization-Personalization-functions_in_HMI-Menue_visible" > Adjust the value to "active".
> Channel "Personalization-Personalization_Profile function" > Adjust value to "profiles_active".
> Channel "Personalization-Profile_Variant" > Adjust value to "Account (v. 1.x)".
> Channel "Personalization-PSO_FSG_Setup2_Bit_1" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_2" > Adjust value to "active".
> Channel "Personalization-PSO_FSG_Setup2_Bit_3" > Adjust value to "active".(only if STG 36 installed)
> Channel "Personalization-PSO_FSG_Setup2_Bit_4" > Adjust value to "not active".

Activate STG 17 > Coding > Byte 10 > Bit 0

Set STG 08 > Coding > Byte 15 > Bit 3-4 to "08 Personalization, activated".

Set STG 36 > Coding > Byte 09 > Bit 1-2 to "02 Func_key_memory_personalization, personalization active".

Set STG A5 > Coding > Byte 13 > Bit 3-5 to "10 Personalized_key,Version_1.x".

Pace car flashing rear lights (LED rear lights) (Golf 7 AU)
STG 09 > Access Permission: 31347 > Customization > …

> Channel "Luminaire16BLK SLB35BLK SL KC9 light function A 16" > Adapt value to "Flashing left dark phase" (factory setting: light phase)
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function A 17" > Adapt value to "Flashing right dark phase" (factory setting: light phase)

Pace car rear lights flashing (only when opening/closing the vehicle) (LED rear lights) (Golf 7 AU)

STG 09 > access permission: 31347 > customization > …

> Channel "Dynamic flashing modes-ZV_Blinken_zu" > Set value to "active".

> Channel "Dynamic flashing mode ZV_Blinken_auf" > Set value to "active".
> Channel "Luminaire16BLK SLB35BLK SL KC9 light function C 16" > Set the value to "Active flashing function has an assigned bit set to 1
in pa_dynamisch_blinken".
> Channel "Luminaire16BLK SLB35BLK SL KC9 dimming value CD 16" > Set value to "100".
> Channel "Luminaire16BLK SLB35BLK SL KC9 light function E 16" > Set value to "Flashing right light phase".
> Channel "Luminaire16BLK SLB35BLK SL KC9 dimming value EF 16" > Set value to "0".
> Channel "Luminaire16BLK SLB35BLK SL KC9-Dimming Direction EF 16" > Set value to "minimize".

© 2013-2020 Daniel Fuchs page 50

 > Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function C 17" > Set the value to "Active flashing function has an assigned bit set to 1
in pa_dynamisch_blinken".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value CD 17" > Set value to "100".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function E 17" > Set value to "Left flashing light phase".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value EF 17" > Set value to "0".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3-Dimming Direction EF 17" > Set the value to "minimize".

Pace car flashing of the rear lights (only with hazard warning lights) (LED rear lights) (Golf 7 AU)

STG 09 > Access Permission: 31347 > Customization > …

> Channel "Dynamic flashing modes-Warnblinken_Zundung_EIN" > Set value to "active".

> Channel "Dynamic flashing modes-Warnblinken_Zundung_AUS" > Set value to "active".
> Channel "Luminaire16BLK SLB35BLK SL KC9 light function C 16" > Set the value to "Active flashing function has an assigned bit set to 1
in pa_dynamisch_blinken".
> Channel "Luminaire16BLK SLB35BLK SL KC9 dimming value CD 16" > Set value to "100".
> Channel "Luminaire16BLK SLB35BLK SL KC9 light function E 16" > Set value to "Flashing right light phase".
> Channel "Luminaire16BLK SLB35BLK SL KC9 dimming value EF 16" > Set value to "0".
> Channel "Luminaire16BLK SLB35BLK SL KC9-Dimming Direction EF 16" > Set value to "minimize".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function C 17" > Set the value to "Active flashing function has an assigned bit set to 1
in pa_dynamisch_blinken".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value CD 17" > Set value to "100".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 light function E 17" > Set value to "Left flashing light phase".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3 dimming value EF 17" > Set value to "0".
> Channel "Luminaire17TFL R BLK SRB3TFL R BLK SR KC3-Dimming Direction EF 17" > Set the value to "minimize".

Parking light on both sides

No matter what position the steering column switch is set to - except "0" - parking lights are active on both sides (compared to normal only the corresponding side)

STG 09 > Access authorization: 31347 > Adaptation > Channel "Headlights and parking lights activated via LSS" > Change value to "both
sides" (factory setting: one side)

© 2013-2020 Daniel Fuchs page 51

Radio receiving amplifier

STG 5F > Access Permission: 20103 > Customization > …

> "Audio management input gain radio (FM)" channel > Adjust the value to "127" (factory setting: -127)
> Channel "Audio management input gain radio (AM)" > Adjust value to "127" (factory setting: -127)
> Channel "Audio management input gain - digital radio (DAB)" > Adjust the value to "127" (factory setting: -127)

Tire pressure control display (direct, TPMS) - activation/activation

Activate STG 19 > Installation list > "65 - Tire pressure".

STG 03 > Coding > …

> Byte 27 > Bit 4, 5 and 6 disable

> Byte 28 > Bit 7 disable

STG 17 > Coding > …

> Byte 03 > Activate bit 7 ("Tyre pressure control, yes")

> Byte 04 > Deactivate bit 0 ("Tire pressure indicator,yes")
> Byte 11 > Activate bit 2 ("Tyre pressure control: BAP route,yes")

STG 5F > Customization > …

> Channel "Vehicle function list BAP-tire_pressure_system_0x07" > Set value to "activated".
> Channel "Vehicle function list BAP-tire_pressure_system_0x07_msg_bus" > Set value to "Data bus extended".

STG 65 > Access Permission: 20103

> Channel "Write sensor identification number - wheel position" > Set value to "Rear right".

After the coding has been completed, parameters for the tire pressures must still be generated and with VCP or similar. be uploaded. To create the parameters can do
thatTPMS tool be used by jolt.

Tire pressure monitoring display (indirect, via ABS) - activation/activation (retrofitting)

STG 03 > Coding > …

© 2013-2020 Daniel Fuchs page 52

 > Byte 27 > Activate bit 5
> Byte 28 > Activate bit 7

STG 5F > Customization > …

> Channel "Vehicle function list BAP-tire_pressure_system_0x07" > Set value to "active".
> Channel "Vehicle function list BAP-tire_pressure_system_0x07_msg_bus" > Set value to "Chassis data bus".
> Channel "Vehicle menu operation-menu_display_rdk" > Set value to "active".
> Channel "Vehicle menu operation-menu_display_rdk_over_threshold_high" > Set value to "active".

Activate STG 17 > Coding > Byte 04 > Bit 0 ("Indirect tire pressure monitoring system (TPMS)")

Reversing camera (low) - activation/activation (retrofit)

Activate STG 10 > Coding > Byte 02 > Bit 4

Activate STG 5F > Coding > Byte 19 > Bit 4

Reversing Camera (Low) - Disable deactivation when tailgate is open

STG 5F > Customization > Channel "Vehicle configuration-rvc_low_black_screen_trunk_open" > Set value to "not activated".

Reversing Camera (Low) - Disable speed dependent deactivation

STG 5F > Customization > Channel "Vehicle configuration-rvc_low_black_screen_velocity_threshold" > Set value to "not activated".

Increase reversing light luminosity (Golf 7 AU)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire28RFL LC11 dimming value AB 28" > Set value to "100" (factory setting: 86)
> Channel "Luminaire29RFL RA64 dimming value AB 29" > Set value to "100" (factory setting: 86)

© 2013-2020 Daniel Fuchs page 53

Sliding roof - make the display position accessible directly from the sliding position

STG 09 > Coding > Sunroof (J245 PS24.402) > ...

> Byte 01 > Activate bit 1

> Byte 01 > Activate bit 2

Sunroof - Do not cancel the closing process when the door is opened (with STG CA)

Activate STG CA > Coding > Byte 00 > Bit 6 (Continue_closing_movement_without_BCM_FH_Freigabe)

Sunroof - Do not cancel the closing process when the door is opened (without STG CA)

Activate STG 09 > Coding > Sunroof (J245 PS24.402) > Byte 00 > Bit 7

Sunroof - change mode when opening conveniently

STG 09 > Access authorization: 31347 > Adaptation > Channel "Access control 2-SAD direction comfort opening" > Change value to "open" (factory setting: tilting)

...if STG CA is installed, then additionally...

STG CA > Adaptation > Channel "Comfort functions - target position for comfort opening" > Change value to "Sliding position" (factory setting: opening position)

Sunroof - decouple roller blind from the roof (with STG CA)

STG CA > Encoding > Byte 02 > Bit 6 disable

Sunroof - decouple roller blind from the roof (without STG CA)

STG 09 > Coding > Sunroof blind (J394 PS24.402) > Byte 00 > Bit 0 deactivate

© 2013-2020 Daniel Fuchs page 54

Tail light inside active at Coming Home/Leaving Home

STG 09 > Access authorization: 31347 > Adaptation > Channel "Luminaire27NSL RC6 light function B 27" > Adapt value to "Coming Home or Leaving Home
active".

Rear light inside double function as brake light (for LED rear lights) (Golf 7 AU)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire27NSL RC6 light function C27" > Set value to "Brake light" (factory setting: not active)
> Channel "Luminaire27NSL RC6 dimming value CD27" > Set value to "100" (factory setting: 0)

Rear light inside double function as brake light (for halogen rear lights) (Golf 7 AU)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire23SL HLC10 light function C23" > Set value to "Brake light" (factory setting: not active)
> Channel "Luminaire23SL HLC10_Dimmwert CD23" > Set value to "100" (factory setting: 0)
> Channel "Luminaire24SL HRA65 light function C24" > Set value to "Brake light" (factory setting: not active)
> Channel "Luminaire24SL HRA65_Dimmwert CD24" > Set value to "100" (factory setting: 0)

Deactivate tail light inside double function as brake light with active rear fog light (legal requirement according to StVZO)

STG 09 > access permission: 31347 > customization > …(Example of LED taillights)

> Channel "Light27NSL RC6 light function E 27" > Set value to "Rear fog light if no trailer is plugged in" (factory setting: not active)
> Channel "Luminaire27NSL RC6 dimming value EF 27" > Set value to "10" (factory setting: 0)
> Channel "Luminaire27NSL RC6-Dimming Direction EF 27" > Set value to "minimize" (factory setting: maximize)

Seats - activate "Easy Entry" comfort entry (electric seats)

Activate STG 36 > Coding > Byte 03 > Bit 1

© 2013-2020 Daniel Fuchs page 55

Seats - Activate "Easy Entry" menu item (electric seats)
STG 36 > Coding > …

> Byte 09 > Activate bit 6 (easy_entry_front_over_MMI)

> Byte 06 > Activate bit 4 (EasyEntry_Enable_Passenger_over_DriverMMI)(only run if STG 06 is installed)

STG 5F > Customization > …

> Channel "Function_Adaptations_Gen2-menu_display_seat_configuration" > Set value to "enabled".

> Channel "Function_Adaptations_Gen2-menu_display_seat_configuration_over_threshold_high" > Set value to "enabled".

Seat heating - Adjust temperatures of the stages

STG 09 > access permission: 31347 > customization > …

> Channel "Assignment of current consumption for seat heating stages - seat heating stage 1 lower switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 1 upper switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 2 lower switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 2 upper switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 3 lower switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 3 upper switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 4 lower switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 4 upper switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 5 lower switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 5 upper switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 6 lower switching threshold" > Adjust value in °C
> Channel "Assignment of current consumption for seat heating stages - seat heating stage 6 upper switching threshold" > Adjust value in °C

Depending on the vehicle, different levels are used. On the Octavia III and Golf 7, levels 1 and 2, 3 and 4, and 5 and 6 are the same. With the Leon 5F, only levels
2, 4 and 6 are occupied.

Seat heating - save selected seat heating level

STG 08 > Customization > …

© 2013-2020 Daniel Fuchs page 56

 > Channel "Storage of driver's seat heating level" > Set value to "active" or "active for 10 minutes".
> Channel "Storage of passenger seat heating level" > Set value to "active" or "active for 10 minutes".

Seat heating - adjust return thresholds (Audi A3 8V)

STG 08 > Adaptation > Channel "Time until seat heating reduction level X to level Y" > Adapt value in min (0 = function deactivated)

Set daylight saving time automatically

STG 5F > Adaptation > "Summer time automatic" channel > Set value to "Europe" (factory setting: manual)

After successful coding, activate the check mark for "Automatically set daylight saving time" in the CAR menu under "Time and date".

Deactivate the sound actuator or reduce the volume

STG A9 > Adaptation > "Volume of the actuator for structure-borne noise" channel > Adjust the value accordingly (factory setting: 100)

Sound system - expansion of the internal sound system (without external amp) with virtual surround and subwoofer

STG 5F > Coding > Byte 11 > Change to "04" (Sound_System_internal_individual)

Activate mirror - lowering of the passenger side

STG 09 > access permission: 31347 > customization > …

> Channel "Access control 2-mirror lowering when reversing" > Set value to "active".
> Channel "Access control 2 menu control mirror reduction" > Set value to "active".

Activate STG 42 > Coding > Byte 04 > Bit 1, 2 and 3

Activate STG 52 > Coding > Byte 04 > Bit 2 and Bit 3

© 2013-2020 Daniel Fuchs page 57

Mirror - folding - activation
STG 42 > Coding > …

> Byte 04 > Activate bit 4 ("Foldable Mirrors installed")

> Byte 04 > Activate bit 6 ("Comfort Mirror Folding active")

STG 52 > Coding > …

> Byte 04 > Activate bit 4 ("Foldable Mirrors installed")

> Byte 04 > Activate bit 6 ("Comfort Mirror Folding active")

Mirrors - folding also active while driving

STG 42 > Coding > Byte 09 > Activate bit 7
STG 52 > Coding > Byte 09 > Activate bit 7

Adjust mirror folding via FFB mode

STG 09 > Access authorization: 31347 > Adaptation > Channel "Access control 2-radio mirror folding mode"

"by look command via remote control key" > Mirrors fold in immediately when locking via FFB
"convenience operation via remote control key" > Mirrors only fold in when the lock button on the key is pressed for 2-3 seconds

Mirrors - Ambient lighting active when mirrors are folded in

Deactivate STG 42 > Coding > Byte 01 > Bit 5

STG 52 > Coding > Byte 01 > Bit 5 deactivate

Spoiler - do not lower when locking the vehicle (Audi TT 8S)

STG 09 > Access authorization: 31347 > Adaptation > Channel "Additional functions-spoiler comfort lowering of the spoiler via locking cylinder FT" > Set value to
"active".

© 2013-2020 Daniel Fuchs page 58

Spoiler - do not lower automatically after manual extension (Audi TT 8S)

STG 09 > Access authorization: 31347 > Adaptation > Channel "Additional functions-spoiler retraction suppression after manual extension" > Set value to "active".

Activate voice control (Audi A3 8V)

This adjustment is often no longer possible because the function is now secured using SWaP.

Activate STG 5F > Coding > Byte 24 > Bit 1

Lane Keeping Assist (Lane Assist) - Activation (Variant 1)

Multifunction camera (control unit A5 - "MQB_MFK") must be installed, e.g. installed when ordering with DLA and/or VZE! After successful coding, you should
wait for the bus to stop.

STG A5 > Encoding > Byte 00 > Activate bit 0 ("Lane Departure Warning System (HCA) active/installed")

STG A5 > Access Permission: 20103 > Customization > …

> Channel "HCA_On_State" > Set value to "Menu".

> Channel "HCA_Warning_Intensity" > Set value to "Menu".
> Channel "BAP_Personalization" > Set value to "not activated".
> "Time of intervention" channel > Set value to "late (setting via menu)".
> Set channel "Personalization of lane departure warning at Kl.15" > to "last setting".

STG 5F > Customization > …

> Channel "Vehicle function list BAP; Extension_LDW_HCA_0x19" > Set value to "activated".
> Channel "Vehicle function list BAP; extension_LDW_HCA_0x19_msg_bus" > set value to "data bus extended".
> Channel "Vehicle Menu Operation-menu_display_Lane_Departure_Warning" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_Lane_Departure_Warning_over_threshold_high" > Set to "activated".

STG 17 > Coding > …

> Byte 04 > Activate bit 6 ("Lane Assist / Lane Assist installed")
> Byte 11 > Activate bit 1 ("Lane Assist / Lane Assist Information (BAP) installed/active")

© 2013-2020 Daniel Fuchs page 59

STG 44 > access authorization: 19249 > coding > byte 00 > activate bit 4 ("lane departure warning system installed")

Lane Keeping Assist (Lane Assist) - Activation (Variant 2)

Multifunction camera (control unit A5 - "MQB_B_MFK")must be installed, e.g. E.g. when ordering with DLA and/or VZE installed! After successful
coding, you should wait for the bus to stop. Coding in STG 10 is only necessary if the corresponding bit is labeled as such or errors remain in the
STG.

Activate STG A5 > Coding > Byte 16 > Bit 7 ("Lane Departure Warning System (HCA) active/installed [PR-7Y9]")

STG A5 > Access Permission: 20103 > Customization > …

> Channel "Personalisation time of intervention at term. 15 on" > Set value to "Last setting".
> Channel "Personalization BAP" > Set value to "not active".
> Channel "Activation state lane departure warning system" > Set value to "on (setting via menu)".

STG 5F > Customization > …

> Channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19" > Set value to "activated".

> Channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus" > Set value to "Data bus extended".
> Channel "Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning" > Set value to "activated".
> Channel "Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning_over_threshold_high" > Set value to "activated".

STG 17 > Coding > …

> Byte 04 > Activate bit 6 ("Lane Assist / Lane Assist installed")
> Byte 11 > Activate bit 1 ("Lane Assist / Lane Assist Information (BAP) installed/active")

STG 44 > access authorization: 19249 > coding > byte 03 > activate bit 0 ("lane departure warning system installed")

STG 10 > access authorization: 71679 > coding > byte 03 > activate bit 5 ("lane departure warning system with steering assistance installed")

Lane Keeping Assist (Lane Assist) - Activation (Variant 3)

Multifunction camera (control unit A5 - "MQB MFK 3.0") must be installed, e.g. installed when ordering with DLA and/or VZE. Once the coding has been completed,
you should wait until the bus is idle. The coding in STG 10 is only necessary if the corresponding bit is also labeled as such or there are errors in the STG stay behind.

© 2013-2020 Daniel Fuchs page 60

STG A5 > Coding > …

> Byte 08 > Set bit 5-7 to "A0 Point_of_intervention,late_setting_over_menu".

> Byte 09 > Set bit 0-1 to "03 Configuration_for_lane_departure_warning_Kl15,Last_setting".
> Byte 09 > Set bit 2-3 to "0C Lane_assist_system_mode,Selection_over_menu".
> Byte 17 > Activate bit 0 ("Hc_messages,0=not_coded / 1=coded")
> Byte 17 > Set bits 1-3 to "02 HC_Warn_Intensity,Setting_over_Menu".
> Byte 17 > Set bits 5-7 to "20 Hc_variant,variant_1".

STG 5F > Customization > …

> Channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19" > Set value to "activated".

> Channel "Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus" > Set value to "Data bus extended".
> Channel "Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning" > Set value to "activated".
> Channel "Car_Function_Adaptations_Gen2-menu_display_Lane_Departure_Warning_over_threshold_high" > Set value to "activated".

STG 17 > Coding > …

> Byte 04 > Activate bit 6 ("Lane Assist / Lane Assist installed")
> Byte 11 > Activate bit 1 ("Lane Assist / Lane Assist Information (BAP) installed/active")

STG 44 > access authorization: 19249 > coding > byte 03 > activate bit 0 ("lane departure warning system installed")

STG 10 > access authorization: 71679 > coding > byte 03 > activate bit 5 ("lane departure warning system with steering assistance installed")

Lane Departure Warning - driver inactivity deactivation threshold

STG A5 > Access authorization: 20103 > Adaptation > "Driver inactivity deactivation threshold" channel > Adapt value (factory setting: medium)

Lane departure warning system - set the time of intervention via the menu

Set STG A5 > Coding > Byte 14 > Bit 5-7 to "A0 Time of intervention: late (setting via menu)".

Lane Departure Warning - adjust the intensity of the steering wheel vibration

STG A5 > Access authorization: 20103 > Adaptation > "Steering wheel vibration intensity" channel > Adjust value accordingly (factory setting: medium)

© 2013-2020 Daniel Fuchs page 61

Lane Departure Warning - adjust the intensity of the steering assistance

STG A5 > Access authorization: 20103 > Adaptation > "Steering wheel support intensity" channel > Adjust value (factory setting: medium)

Lane departure warning - set warning strength via menu (variant 1)

A front/fore camera controller part number 5Q0 is required.

STG A5 > Access Permission: 20103 > Customization > Channel "HCA_Warning_Intensity" > Set value to "Menu".

or.
STG A5 > Access authorization: 20103 > Adaptation > Channel "Warning intensity lane departure warning" > Set value to "Selection via menu".

Lane departure warning - set warning strength via menu (variant 2)

A front/fore camera controller with part number 3Q0 is required.

STG A5 > Coding > Byte 13 > Bit 1-2 to "06 system mode lane departure warning, selection via menu"

Auxiliary heating - adjust post-heating time

STG 08 > Adaptation > Channel "Reheating time of the auxiliary heating" > Adjust value in min (factory setting: 10)

Auxiliary heating - adjust the temperature for activating the interior fan

STG 18 > Adaptation > Channel "Control parameters parking heater temperature threshold for activation of fresh air blower" > Adjust value in °C

Auxiliary heating - adjust temperatures for auxiliary heater operation

STG 18 > Customization > …

> Channel "Control parameters for additional heating - lower temperature threshold, ambient temperature" > Adjust the value in °C
> Channel "Additional heating control parameters - upper temperature threshold ambient temperature" > Adjust value in °C

© 2013-2020 Daniel Fuchs page 62

Disable start/stop function
STG 19 > Customization > …

> Channel "EM_start_stop_requirement_ambient_temperature-Minimum_temperature" > Change value to "50" (factory setting: -50)
> Channel "EM_start_stop_requirement_ambient_temperature-Maximum_temperature" > Change value to "50" (factory setting: -50)

or
> Channel "Start/Stop starting voltage limit" > Change value to "12" (factory setting: 7.6)

SWRA - deactivation

Deactivate STG 09 > Coding > Byte 13 > Bit 3

SWRA - change the delay time before triggering

STG 09 > Access permission: 31347 > Adaptation > Channel "windscreen wiper SRA delay time > Adapt value in milliseconds (maximum 2500 ms)

SWRA - adjust washing behavior (frequency, duration)

STG 09 > access permission: 31347 > customization > …

> Channel "Number of windscreen wiper operations front washer system per SRA activation" > Adjust value
> Channel "Windscreen wiper SRA wash time" > Adjust value in milliseconds
> Windshield wiper SRA soak pause time channel > Adjust value in milliseconds
> "Windscreen wiper SRA post-wash time" channel > Adjust value in milliseconds

The entire washing process is split into two separate spray processes, the times can be adjusted as desired. The longer the washing times, the sooner
your wiper water tank is empty!

Daytime running lights - switch off when the handbrake is pulled

STG 09 > Access authorization: 31347 > Adaptation > Channel "Turn off daytime running lights - daytime running lights with handbrake" > Set value to "active".

© 2013-2020 Daniel Fuchs page 63

Daytime running lights - dimming when blinking

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire2SL VL B10 light function E 2" > Set value to "Flashing left active (both phases)" (factory setting: not active)
> Channel "Luminaire2SL VL B10 dimming value EF 2" > Set percentage as desired (factory setting: 0)
> Channel "Luminaire2SL VL B10-Dimming Direction EF 2" > Set value to "minimize" (factory setting: maximize)
> Channel "Luminaire3SL VR B21 light function E 3" > Set value to "Flashing right active (both phases)" (factory setting: not active)
> Channel "Luminaire3SL VR B21 dimming value EF 3" > Set percentage as desired (factory setting: 0)
> Channel "Luminaire3SL VR B21-Dimming Direction EF 3" > set to "minimize" (factory setting: maximize)

Daytime running lights - dimming when blinking (slow dimming) (Seat Leon 5F)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire2SL VL B10 light function E 2" > Set value to "Flashing left active (both phases); dimming up and down with p_t_blinken_rampe".
> Channel "Luminaire2SL VL B10 dimming value EF 2" > Set percentage as desired
> Channel "Luminaire2SL VL B10-Dimming Direction EF 2" > Set value to "minimize".
> Channel "Luminaire3SL VR B21 light function E 3" > Set value to "Flashing right active (both phases); dimming up and down with p_t_blinken_rampe".
> Channel "Luminaire3SL VR B21 dimming value EF 3" > Set percentage as desired
> Set channel "Luminaire3SL VR B21-Dimming Direction EF 3" > to "minimize".

Daytime running lights - disable dimming when blinking (Audi A3 8V)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire2SL VL B10 dimming value CD 2" > Set value to "100" (factory setting: 30)
> Channel "Luminaire3SL VR B21 dimming value CD 3" > Set value to "100" (factory setting: 30)

Daytime running lights - Simultaneous flashing with the turn signal (or alternately)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire2SL VLB10 light function G 2" > Adapt value to "Blink left dark phase".
> Channel "Luminaire2SL VLB10 dimming value GH 2" > Adjust value to "0".
> Channel "Luminaire2SL VLB10-Dimming Direction GH 2" > Adjust value to "minimize".
© 2013-2020 Daniel Fuchs page 64
 > Channel "Luminaire3SL VRB21 light function G 3" > Adapt value to "Flashing right dark phase".
> Channel "Luminaire3SL VRB21 dimming value GH 3" > Adjust value to "0".
> Channel "Luminaire3SL VRB21-Dimming Direction GH 3" > Adjust the value to "minimize".

For the blinkin exchangemust be set instead of "Flashing left/right light phase".

Daytime running lights - Inactive in LDS position 0

STG 09 > Access authorization: 31347 > Adaptation > Channel "Daytime running lights only in switch position AUTO" > Set value to "active".

Daytime running lights - activate the menu item in the CAR menu

STG 09 > Access authorization: 31347 > Adaptation > Channel "Daytime running light activation by BAP or operating sequence possible" > Set value to "active".

Daytime running lights - fog lights exclusively as daytime running lights

STG 09 > access permission: 31347 > customization > …

> Channel "Light4TFL LB4 light function A 4" > Set value to "not active" (factory setting: daytime running lights)
> Channel "Light4TFL LB4 light function A 4" > Set value to "not active" (factory setting: daytime running lights)
> Channel "Luminaire12NL LB45 light function C 12" > Set value to "Daytime running light" (factory setting: not active)
> Channel "Luminaire12NL LB45 dimming value CD 12" > Set value to "40".
> Channel "Luminaire13NL RB5 light function C 13" > Set value to "Daytime running light" (factory setting: not active)
> Channel "Luminaire13NL RB5 dimming value CD 13" > Set value to "40".

Daytime Running Lights - add fog lights in addition to daytime running lights

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire12NL LB45 light function B 12" > Set value to "Daytime running lights".
> Channel "Luminaire13NL RB5 light function B 13" > Set value to "Daytime running lights".

© 2013-2020 Daniel Fuchs page 65

Daytime running lights - rear lights also active (with KZB and interior button = parking light always active)

STG 09 > Access authorization: 31347 > Adaptation > Channel "Daytime running lights - daytime running lights, continuous running light also activates side lights" > Set value to "active".

Daytime running lights - rear lights also active (without KZB)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire23SL HLC10 light function D 23" > Change value to "Daytime running light" (factory setting: not active)
> Channel "Luminaire24SL HRA65 light function D 24" > Change value to "Daytime running lights" (factory setting: not active)
> Channel "Luminaire26NSL LA72 light function D 26" > Change value to "Daytime running light" (factory setting: not active)
> Channel "Luminaire27NSL RC6 light function D 27" > Change value to "Daytime running light" (factory setting: not active)

Daytime running light - parking light point also active (Golf 7 AU)

STG 09 > access permission: 31347 > customization > …

> Channel "Luminaire8FL LB39 light function C 8" > Set value to "Daytime running lights" previously not active
> Channel "Luminaire8FL LB39 dimming value CD 8" > Set value to "100".
> Channel "Luminaire9FL RB2 light function C 9" > Set value to "Daytime running lights" previously not active
> Channel "Luminaire9FL RB2 dimming value CD 9" > Set value to "100".

Fuel Gauge - Adjustment/Calibration

STG 17 > Access authorization: 20103 > Adaptation > Channel "Offset for values of the tank calibration (calibration) - Offset encoder 1" > Adapt value in l
(factory setting: -12.8; value range: -8.0 to 8.0)

Negative values lower the tank needle, positive ones raise it. Calculations such as remaining range are also affected.

Adjust button lighting (driving profile, ASR, ESP) brightness

STG 09 > Access authorization: 31347 > Adaptation > Channel "Interior lighting KL 58xd PWM-Y?" > Set value to in percent (factory setting: 10)

All Y values must be adjusted. These can all be set to one value, or replicate the curve

© 2013-2020 Daniel Fuchs page 66

Traffic Jam Assist & Emergency Assist Unlock
The prerequisite is an ACC with 11-byte+ coding and the Lane Assist with front camera (STG A5), for which there are corresponding parameters in VCP
(currently available for Index G/H). The apron camera can possibly also be updated to a new version, in which case byte 14 bit 2-3 must also be set to "08
Perso_HC, Last setting".

STG A5 > Upload parameters for TRAFFIC_ASSIST (EraseFullMemory active) (VCP )

Set STG A5 > Coding > Byte 16 > Bit 2-3 to "08 EA_Variant2".

Activate STG 03 > Coding > Byte 29 > Bit 5

STG 13 > Coding > Byte 04 > Activate bit 2 ("Emergency Assist installed")

STG 09 > Access authorization: 31347 > Adaptation > "External light_indicator-warning_blinking_through_driver assistance" channel > Set value to "active".

or
Activate STG 09 > Coding > Byte 06 > Bit 3

Ambient lighting - activation/activation (retrofit)

Activate STG 42 > Coding > Byte 01 > Bit 2

Activate STG 52 > Coding > Byte 01 > Bit 2

Perimeter Lighting - Use as a maneuvering light

A control unit for Area View or RFK High (STG 6C) is required. The control unit must have at least software version 0607.

STG 09 > Access authorization: 31347 > Adaptation > Channel "Outside light_overlapping-surrounding light as maneuvering light" > Set value to "active".

Activate STG 6C > Coding > Byte 08 > Bit 2

US parking lights explicitly only in the parking light switch position

STG 09 > access permission: 31347 > customization > …

© 2013-2020 Daniel Fuchs page 67

 > Channel "Light 0 BLK VL B36 light function C 0" > Set value to "Front parking light (position light; side light)".
> Channel "Luminaire 0 BLK VL B36 dimming value CD 0" > Set percentage as desired (factory setting: 0)
> Channel "Luminaire1BLK VRB20 light function C 1" > Set value to "Front parking light (position light; side light)".
> Channel "Luminaire1BLK VRB20 dimming value CD 1" > Set percentage as desired (factory setting: 0)

Emulate US parking lights via ambient lighting (dimmable/switchable in the CAR menu)

If the coding is unsuccessful, it may be that "ambient light 3" and "ambient_application strips_in_door panel" must be used.

STG 09 > access permission: 31347 > customization > …

> Channel "Interior Light Lamp Configuration Ambience_Application Bars_in_Instrument Panel" > Set value to "installed".
> Channel "Interior light lamp configuration-ambient menu with global off" > Set value to "active".
> Channel "Light 0 BLK VL B36 light function A 0" > Set value to "Ambient light 1".
> Channel "Luminaire 0 BLK VL B36 dimming value AB 0" > Set percentage as desired
> Channel "Light 0 BLK VL B36 light function C 0" > Set value to "Handbrake is applied".
> Channel "Light 0 BLK VL B36 light function D 0" > Set value to "Interior light".
> Channel "Luminaire 0 BLK VL B36 dimming value CD 0" > Set value to "0".
> Channel "Luminaire 0 BLK VL B36-Dimming Direction CD 0" > Set value to "minimize".
> Channel "Light 0 BLK VL B36 light function F 0" > Set value to "Flashing left light phase".
> Channel "Light 0 BLK VL B36 dimming value EF 0" > Set value to "100".
> Channel "Light 0 BLK VL B36-Dimming Direction EF 0" > Set value to "maximize".
> Channel "Light 0 BLK VL B36 light function H 0" > Set value to "Flashing left dark phase".
> Channel "Light 0 BLK VL B36 dimming value GH 0" > Set value to "0".
> Channel "Light 0 BLK VL B36-Dimming Direction GH 0" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function A 0" > Set value to "Ambient light 1".
> Channel "Luminaire1BLK VRB20 dimming value AB 0" > Set percentage as desired
> Channel "Luminaire1BLK VRB20 light function C 0" > Set value to "Handbrake is applied".
> Channel "Luminaire1BLK VRB20 light function D 0" > Set value to "Interior light".
> Channel "Luminaire1BLK VRB20 dimming value CD 0" > Set value to "0".
> Channel "Luminaire1BLK VRB20-Dimming Direction CD 0" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function F 1" > Set value to "Blink left light phase".
> Channel "Luminaire1BLK VRB20 dimming value EF 1" > Set value to "100".
> Channel "Luminaire1BLK VRB20-Dimming Direction EF 1" > Set value to "maximize".

© 2013-2020 Daniel Fuchs page 68

 > Channel "Luminaire1BLK VRB20 light function H 1" > Set value to "Flashing left dark phase".
> Channel "Luminaire1BLK VRB20 dimming value GH 1" > Set value to "0".
> Channel "Luminaire1BLK VRB20-Dimming Direction GH 1" > Set value to "minimize".

Controlling the US side lights via the Sport driving profile (Leon III 5F)

STG 09 > access permission: 31347 > customization > …

> Channel "Light 0 BLK VL B36 light function A 0" > Set value to "Ambient light 4".
> Channel "Luminaire 0 BLK VL B36 dimming value AB 0" > Set percentage as desired
> Channel "Light 0 BLK VL B36 light function E 0" > Set value to "Flashing left light phase".
> Channel "Luminaire 0 BLK VL B36 dimming value EF 0" > Set value to "100" (H7) or "127" (LED).
> Channel "Luminaire1BLK VRB20 light function A 1" > Set value to "Ambient light 4".
> Channel "Luminaire1BLK VRB20 dimming value AB 1" > Set percentage as desired
> Channel "Luminaire1BLK VRB20 light function E 1" > Set value to "Blink left light phase".
> Channel "Luminaire1BLK VRB20 dimming value EF 1" > Set value to "100" (H7) or "127" (LED).

and if desired

> Channel "Daytime running light-Daytime running light, continuous running light activates additional parking light" > Set value to "active".

Like the ambient lighting, the light is only active with the side lights and low beam. The last adaptation allows the light to be used in daytime running lights as well.
The disadvantage here is that both the rear lights and the interior lighting (buttons, etc.) are permanently active.

US daytime running lights or parking lights (indicators permanently dimmed with daytime running lights or parking lights/low beam)

STG 09 > access permission: 31347 > customization > …

> Channel "Light 0 BLK VL B36 light function C 0" > Value to "General parking light"or"Set daytime running lights" (factory setting: not active)
> Channel "Light 0 BLK VL B36 dimming value CD 0" > Set percentage as desired (factory setting: 0)
> Channel "Light1BLK VR B20 light function C 1" > Value to "General parking light"or"Set daytime running lights" (factory setting: not active)
> Channel "Luminaire1BLK VR B20 dimming value CD 1" > Set percentage as desired (factory setting: 0)

Dimming does not work with LED indicators such as the Golf 7 R or Seat Leon FR 5F.

© 2013-2020 Daniel Fuchs page 69

US daytime running lights or parking lights - cancellation of dimming when blinking

STG 09 > access permission: 31347 > customization > …

> Channel "Light 0 BLK VL B36 light function E0" > Set value to "Flashing left dark phase".
> Channel "Luminaire 0 BLK VL B36-Dimming Direction EF0" > Set value to "minimize" (factory setting: maximize)
> Channel "Luminaire1BLK VR B20 light function E1" > Set value to "Flashing right dark phase".
> Channel "Luminaire1BLK VR B20-Dimming Direction EF1" > Set value to "minimize" (factory setting: maximize)

US daytime running lights in addition to the normal daytime running lights - switchable via the CAR menu

The coding allows a change between the normal daytime running lights and normal daytime running lights+US daytime running lights in light switch position
»0«. For parking light and low beam you have to decide on one version in the coding.

STG 09 > access permission: 31347 > customization > …

> Channel "Daytime running light-Daytime running light activation by BAP or operating sequence possible" > Set value to "active".
> Channel "Light 0 BLK VL B36 light function A 0" > Set value to "active 100%".
> Channel "Light 0 BLK VL B36 dimming value AB 0" > Set value to "0".
> Channel "Light 0 BLK VL B36 light function C 0" > Set value to "Daytime running lights".
> Channel "Luminaire 0 BLK VL B36 dimming value CD 0" > Set percentage as desired
> Channel "Luminaire 0 BLK VL B36-Dimming Direction CD 0" > Set value to "maximize".
> Channel "Light 0 BLK VL B36 light function F 0" > Set value to "Flashing left light phase".
> Channel "Light 0 BLK VL B36 dimming value EF 0" > Set value to "100".
> Channel "Luminaire 0 BLK VL B36-Dimming Direction EF 0" > Set value to "minimize".
> Channel "Light 0 BLK VL B36 light function H 0" > Set value to "Flashing left dark phase".
> Channel "Light 0 BLK VL B36 dimming value GH 0" > Set value to "0".
> Channel "Light 0 BLK VL B36-Dimming Direction GH 0" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function A 1" > Set value to "active 100%".
> Channel "Luminaire1BLK VRB20 dimming value AB 1" > Set value to "0".
> Channel "Luminaire1BLK VRB20 light function C 1" > Set value to "Daytime running lights".
> Channel "Luminaire1BLK VRB20 dimming value CD 1" > Set percentage as desired
> Channel "Luminaire1BLK VRB20-Dimming Direction CD 10" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function F 1" > Set value to "Blink left light phase".
> Channel "Luminaire1BLK VRB20 dimming value EF 1" > Set value to "100".
> Channel "Luminaire1BLK VRB20-Dimming Direction EF 1" > Set value to "minimize".
© 2013-2020 Daniel Fuchs page 70
 > Channel "Luminaire1BLK VRB20 light function H 1" > Set value to "Flashing left dark phase".
> Channel "Luminaire1BLK VRB20 dimming value GH 1" > Set value to "0".
> Channel "Luminaire1BLK VRB20-Dimming Direction GH 1" > Set value to "minimize".
> Channel "Luminaire2SL VLB10 light function A 2" > Change the value of "Daytime running lights" to "active 100%".
> Channel "Luminaire3SL VRB21 light function A 3" > Change the value of "Daytime running lights" to "active 100%".
> Channel "Luminaire4TFL LB4 light function A 4" > Change the value of "Daytime running lights" to "Terminal 15 with run-on until the vehicle comes to a standstill".
> Channel "Light 5 TFL RB32 light function A 5" > Change the value from "Daytime running lights" to "Terminal 15 with run-on until the vehicle comes to a standstill".

and if desired (then the US lighting is on with parking lights/low beams, otherwise always off)

> Channel "Light 0 BLK VL B36 light function D 0" > Set the value to "General parking light (tail light; position light; side light)".
> Channel "Light1BLK VRB20 light function D 1" > Set the value to "General parking light (tail light; position light; side light)".

US daytime running lights/normal daytime running lights - switchable via CAR menu

The coding allows you to switch between the normal daytime running lights and the US daytime running lights in the light switch position »0«. For parking light and low
beam you have to decide on one version in the coding.

STG 09 > access permission: 31347 > customization > …

> Channel "Daytime running light-Daytime running light activation by BAP or operating sequence possible" > Set value to "active".
> Channel "Light 0 BLK VL B36 light function A 0" > Set value to "active 100%".
> Channel "Luminaire 0 BLK VL B36 dimming value AB 0" > Set percentage as desired
> Channel "Light 0 BLK VL B36 light function C 0" > Set value to "Daytime running lights".
> Channel "Luminaire 0 BLK VL B36 dimming value CD 0" > Set value to "0".
> Channel "Luminaire 0 BLK VL B36-Dimming Direction CD 0" > Set value to "minimize".
> Channel "Light 0 BLK VL B36 light function F 0" > Set value to "Flashing left light phase".
> Channel "Light 0 BLK VL B36 dimming value EF 0" > Set value to "100".
> Channel "Luminaire 0 BLK VL B36-Dimming Direction EF 0" > Set value to "minimize".
> Channel "Light 0 BLK VL B36 light function H 0" > Set value to "Flashing left dark phase".
> Channel "Light 0 BLK VL B36 dimming value GH 0" > Set value to "0".
> Channel "Light 0 BLK VL B36-Dimming Direction GH 0" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function A 1" > Set value to "active 100%".
> Channel "Luminaire1BLK VRB20 dimming value AB 1" > Set percentage as desired
> Channel "Luminaire1BLK VRB20 light function C 1" > Set value to "Daytime running lights".

© 2013-2020 Daniel Fuchs page 71

 > Channel "Luminaire1BLK VRB20 dimming value CD 1" > Set value to "0".
> Channel "Luminaire1BLK VRB20-Dimming Direction CD 10" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function F 1" > Set value to "Blink left light phase".
> Channel "Luminaire1BLK VRB20 dimming value EF 1" > Set value to "100".
> Channel "Luminaire1BLK VRB20-Dimming Direction EF 1" > Set value to "minimize".
> Channel "Luminaire1BLK VRB20 light function H 1" > Set value to "Flashing left dark phase".
> Channel "Luminaire1BLK VRB20 dimming value GH 1" > Set value to "0".
> Channel "Luminaire1BLK VRB20-Dimming Direction GH 1" > Set value to "minimize".

and if desired (then the US lighting is off for parking lights/dipped beam, otherwise always on)

> Channel "Light 0 BLK VL B36 light function D 0" > Set the value to "General parking light (tail light; position light; side light)".
> Channel "Light1BLK VRB20 light function D 1" > Set the value to "General parking light (tail light; position light; side light)".

Adjust consumption display

STG 17 > Adaptation > "Display correction consumption and range" channel > Adjust percentage (factory setting: 100; value range: 85 to 115)

Activate voice control (Audi A3 8V)

Activate STG 5F > Coding > Byte 24 > Bit 1

Traffic Sign Recognition - Activation (Variant 1)

Multifunction camera (STG A5) must be installed. Function given with MIB2STD and all MIB HIGH. If no HUD (STG 82) is installed, the coding should be
omitted.

Activate STG A5 > coding > byte 01 > bit 0 ("traffic sign recognition (VZE) active")

STG 17 > coding > byte 05 > activate bit 2 ("traffic sign recognition installed/active")

STG 5F > Customization > …

> Channel "Vehicle function list BAP-traffic_sign_recognition_0x21" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_road_sign_identification" > Set value to "activated".
> Channel "Vehicle Menu Operation-menu_display_road_sign_identification_over_threshold_high" > Set value to "activated".

© 2013-2020 Daniel Fuchs page 72

STG 82 > coding > byte 00 > activate bit 0 ("traffic sign recognition, available")

Traffic Sign Recognition - Activation (Variant 2)

Multifunction camera (STG A5) must be installed. If no HUD (STG 82) is installed, the coding should be omitted.

Activate STG A5 > coding > byte 16 > bit 4 ("traffic sign recognition (VZE) active [PR-QR9]")

STG 17 > coding > byte 05 > activate bit 2 ("traffic sign recognition installed/active")

STG 5F > Customization > …

> Channel "Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21" > Set value to "activated".

> Channel "Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus" > Set value to "Data bus extended".
> Channel "Car_Function_Adaptations_Gen2-menu_display_road_sign_identification" > Set value to "activated".
> Channel "Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high" > Set value to "activated".

STG 82 > coding > byte 00 > activate bit 0 ("traffic sign recognition, available")

if errors remain in the ACC control unit, then additionally

STG 13 > Encoding > Byte 01 > Activate bit 0 ("traffic_sign_detection")

Traffic Sign Recognition - Show cancellation signs

STG A5 > access authorization: 20103 > channel "sign end of speed limit" > set to "active".

Video in Motion (VIM) - Activation

VCP > Guided Functions > "VimManager" Function > Customize Parameters

Hazard warning lights - Automatic activation after hard braking

STG 09 > Access authorization: 31347 > Adaptation > Channel "External light_Blinker-Notwarn_blinken_NBA_Phase_2" > Set value to "active".

© 2013-2020 Daniel Fuchs page 73

Hazard warning button - adjust the brightness of the lights

STG 09 > Access Permission: 31347 > Customization > Channel "Turn Signal Control-Hazard Button Search Light Factor" > Change Factor

XDS - Enhanced Electronic Differential Lock Adjust control strength

STG 03 > Adaptation > "Electronic differential lock" channel > Adjust value

Central locking - adjust the duration of the visual feedback

The visual feedback from the ZV is divided into three parts (light-dark-light). The control times can be adjusted with the »Facelift BCMs« (from index
BA) in order to lengthen or shorten the feedback.

STG 09 > access permission: 31347 > customization > …

> Channel "Feedback signals-ZV-Blinken_Darkzeit" > Adjust value in ms (factory setting: 200)
> Channel "Feedback signals-ZV-Blinken_Hellzeit" > Adjust value in ms (factory setting: 200)

Central locking - do not unlock when removing the key

STG 09 > Access authorization: 31347 > Adaptation > "Access control automatic unlocking" channel > Set value to "not active".

© 2013-2020 Daniel Fuchs page 74