Internal Use Only

Website http://biz.lgservice.com

SERVICE MANUAL
300 W STYLISH & SLIM SOUND BAR

MODEL: NB3532A (NB3532A, S33A1-D)

SERVICE MANUAL
MODEL: NB3532A
(NB3532A, S33A1-D)

CAUTION
BEFORE SERVICING THE UNIT, READ THE “SAFETY PRECAUTIONS”
IN THIS MANUAL.

P/NO : AFN76153344 SEPTEMBER, 2013

 CONTENTS

SECTION 1 ........ GENERAL

SECTION 2 ........ CABINET & MAIN CHASSIS
SECTION 3 ........ ELECTRICAL
SECTION 4 ........ REPLACEMENT PARTS LIST

1-1
 SECTION 1
GENERAL

CONTENTS

ESD PRECAUTIONS ....................................................................................................................................... 1-3

MICOM HIDDEN KEY MODE ......................................................................................................................... 1-4

UPDATE PROGRAM ....................................................................................................................................... 1-5

SERVICE INFORMATION FOR EEPROM .................................................................................................... 1-5

SPECIFICATIONS ............................................................................................................................................ 1-6

1-2
 ESD PRECAUTIONS
Electrostatically Sensitive Devices (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated
circuits and some field-effect transistors and semiconductor chip components. The following techniques should
be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off
any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a
commercially available discharging wrist strap device, which should be removed for potential shock reasons
prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive surface
such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static" can
generate electrical charges sufficient to damage ESD devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD
devices.
6. Do not remove a replacement ESD device from its protective package until immediately before you are
ready to install it. (Most replacement ESD devices are packaged with leads electrically shorted together by
conductive foam, aluminum foil or comparable conductive materials).
7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the
protective material to the chassis or circuit assembly into which the device will by installed.

CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER
SAFETY PRECAUTIONS.

8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion
such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate
static electricity sufficient to damage an ESD device).

CAUTION. GRAPHIC SYMBOLS

THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN AN EQUILATERAL TRIANGLE, IS

INTENDED TO ALERT THE SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE

SERVICE PERSONNEL TO THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN SERVICE
LITERATURE.

1-3
 MICOM HIDDEN KEY MODE
HIDDEN MODE ENTRANCE KEY EXIT KEY DISPLAY RESULT
1) Micom,
2) ESS,
3) Touch Key
M 1009303
4) wireless SPK
E 1106151
module TX,RX Ver
Front Stop + RMC T 1106301
Version Check POWER OFF ex) TX35RX35
Play for 5s TX35RX35
5) wireless SPK
R 1007130
Micom Ver
** ** ** ** ** **
ex) W 1007130
6) EEPROM option
value (on Scroll)
Front Stop + RMC '0'
EEPROM INITIAL auto exit "E2P CLEAR" EEPROM initializing
for 5s
Front Stop + RMC '2'
EEPROM EDIT Toggling OP0-10 Edit Micom option
for 5s
Wireless spk Front Stop + RMC Connecting Wireless
Toggling "REMATE:"
remate mute spk to main set
Front Stop + RMC '8'
Clip Off Toggling "CLIP OFF" To Test (output etc.)
for 5s
Monitoring
Front Stop + RMC '8' Monitoring Changed
Changed Gain Toggling -0,0 dB
for 5s Gain at Clip ON
at Clip ON
Front Stop + RMC For Max Volume
MAX Volume Edit Toggling MVOL-XX
'Sleep' for 5s setting (1 ~ 40)

1-4
 UPDATE PROGRAM
1) File Name
Model Name NB3530A
Micom Update Filename MICOM_NB3530_1301030_0xFE5C.hex
ESS Update Filename DSP_NB3530_1212261_7613.rom
Wireless Rx/Tx Module Update Filename WIRELESS.BIN
Wireless Rx Micom Update Filename WIRELESS_MICOM.HEX
Touch Key Filename TOUCH1_NB3530.DLD

2) File Name is in uppercase letters only.

3) PROGRAM DOWNLOAD
1. AUDIO MICOM
BOOTING Ö FUNCTION DISPLAY Ö USB FUNCTION Ö CONNECTING THE USB
Ö “MICOM UP” DISPLAY Ö AFTER UPDATE , THE SET POWER OFF AUTOMATELY.

2. DSP
BOOTING Ö FUNCTION DISPLAY Ö USB FUNCTION Ö CONNECTING THE USB Ö “DSP UP” DISPLAY
Ö AFTER UPDATE , THE SET POWER OFF AUTOMATELY.

3. TOUCH
BOOTING Ö FUNCTION DISPLAY Ö USB FUNCTION Ö CONNECTING THE USB
Ö “T-UP 00” ~ “T-UP 90” DISPLAY Ö AFTER UPDATE , THE SET POWER OFF AUTOMATELY.

SERVICE INFORMATION FOR EEPROM

• FACTORY RESET: SET(STOP KEY) + REMOCON “2”

[ AUDIO MICOM OPTION CODE SETTING ]

SET(STOP KEY) + REMOCON “2” (MORE THAN 5 SECONDS) Ö CHANGE OPTION CODE WITH THE AR-
ROW KEY (REPEAT, PLAY/PAUSE, SKIP KEY) AND PRESS REMOCON STOP KEY Ö SET(STOP KEY) +
REMOCON “2” Ö COMPLETED.

1-5
 SPECIFICATIONS
• GENERAL
Power requirements 120 V ~ 60 Hz
Power consumption 40 W
Dimensions (W x H x D) 950 x 71 x 47 mm (37.4 x 2.8 x 1.9 inches)
Net Weight (Approx.) 2.5 kg (5.5 lbs)
Operating temperature 41 °F to 95 °F (5 °C to 35 °C)
Operating humidity 5 % to 90 %
Bus Power Supply (USB) DC 5 V 500 mA

• INPUTS
DIGITAL IN (OPTICAL IN) 3.0 Vrms (p-p), Optical jack x 2
PORT. IN 0.5 Vrms (3.5 mm stereo jack)

• AMPLIFIER
Stereo mode 80 W + 80 W (4 Ω at 1 kHz), THD 10%
Subwoofer 140 W (3 Ω at 60 Hz), THD 10%

• WIRELESS SUBWOOFER
Power requirements 120 V ~ 60 Hz
Power consumption 40 W
Type 1 Way 1 Speaker
Impedance 3Ω
Rated Input Power 140 W
Max. Input Power 280 W
Dimensions (W x H x D) 196 x 390 x 297 mm (7.7 x 15.4 x 11.7 inches)
Net Weight 5.54 kg (12.2 lbs)

Designs and specifications are subject to change without prior notice.

1-6
 SECTION 2
CABINET & MAIN CHASSIS

CONTENTS

EXPLODED VIEWS ......................................................................................................................................... 2-3

1. RECEIVER BAR SECTION (NB3530A) ................................................................................................... 2-3
2. WIRELESS SUBWOOFER SECTION (S33A1-D) .................................................................................... 2-5
3. PACKING ACCESSORY SECTION ......................................................................................................... 2-7

2-1
MEMO

2-2
EXPLODED VIEWS
1. RECEIVER BAR SECTION (NB3532A)
NOTES) THE EXCLAMATION POINT WITHIN AN
EQUILATERAL TRIANGLE IS INTENDED
TO ALERT THE SERVICE PERSONNEL
TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION IN SERVICE
A44B LITERATURE.
261

263

CABLE5
B

502
C 502

CABLE2
254 A47
502 B
F
262
E
A
SMPS
CABLE3
A44A
502
465 MAIN
250L 261

A43 D
502
253

FRONT A46
463
A

CABLE1 256
D
CABLE7
252
F
A42
B/T E
WIRELESS
A53
A54 502

251 463 300

253
C

254

465

250R
2. WIRELESS SUBWOOFER SECTION (S33A1-D)
NOTES) THE EXCLAMATION POINT WITHIN AN
EQUILATERAL TRIANGLE IS INTENDED
TO ALERT THE SERVICE PERSONNEL
TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION IN SERVICE
LITERATURE.

A900

A
A910 B

A45W A54W A900A

B
950
A
WIRELESS
F C
950
951 C
AMP 950

950 D

950
F

952
952

950
954
D 952

SMPS 300W
E 953
A47W
952
E
3. PACKING ACCESSORY SECTION

801 Owner’s manual 806 Optical cable

829 Cable ties 808 Batteries

for arranging cables

835 Wall bracket 900 Remote control

803 Main packing

804 Bag

803A Packing (Pad)

802 Box

2-7
MEMO

2-8
 SECTION 3
ELECTRICAL

CONTENTS

ONE POINT REPAIR GUIDE .......................................................................................................................... 3-2

1. RECEIVER BAR COMPONENT REPAIR GUIDE .................................................................................. 3-2

ELECTRICAL TROUBLESHOOTING GUIDE ............................................................................................... 3-7

1. RECEIVER BAR TROUBLESHOOTING ................................................................................................ 3-7

WAVEFORMS OF MAJOR CHECK POINT ................................................................................................ 3-11

WIRING DIAGRAMS ...................................................................................................................................... 3-15

1. RECEIVER BAR WIRING DIAGRAM ................................................................................................... 3-15
2. WIRELESS SUBWOOFER WIRING DIAGRAM................................................................................... 3-17

BLOCK DIAGRAMS ...................................................................................................................................... 3-19

1. RECEIVER BAR BLOCK DIAGRAMS .................................................................................................. 3-19
2. WIRELESS SUBWOOFER BLOCK DIAGRAM .................................................................................... 3-23

CIRCUIT DIAGRAMS .................................................................................................................................... 3-25

1. RECEIVER BAR CIRCUIT DIAGRAMS ............................................................................................... 3-25

CIRCUIT VOLTAGE CHART ........................................................................................................................ 3-37

PRINTED CIRCUIT BOARD DIAGRAMS .................................................................................................... 3-41

1. RECEIVER BAR PRINTED CIRCUIT BOARD DIAGRAMS................................................................. 3-41

3-1
 ONE POINT REPAIR GUIDE
1. RECEIVER BAR ONE POINT REPAIR GUIDE
1-1. NO POWER PROBLEM
No power problem occurs when you power on the unit.

1-1-1. 23.5 VA
1-1-1-1. Solution
Replace F900, BD900, IC920, PC900, IC950.

1-1-1-2. How to troubleshoot (Countermeasure)

Case 1) No Standby LED: Check F900, BD900, IC920 and around components Ö Replace these.
Case 2) 23.5 VA abnormal: Check PC900, IC950 Ö Replace these.

BD900

IC920
F900

PC900
IC950

1-1-1-3. Service hint (Any picture / Remark)

BD900

IC920 PC900

F900 IC950
< SMPS board top view >

3-2
RECEIVER BAR ONE POINT REPAIR GUIDE
1-2. POWER ON ERROR
No display or Not working.

1-2-1. DC-DC Converter

1-2-1-1. Solution
Replace IC802 on MAIN board.

1-2-1-2. How to troubleshoot (Countermeasure)

1) Please check T801 voltage(12 V).
Please check CA807(Vkk), CA805(FL+), CA806(FL-).
2) If you cannot get 12 V, IC802 has problem.
If 12 V is OK and VKK, Fl+, FL- is not working, T801 is out of order.

1-2-1-3. Service hint (Any picture / Remark)

T801

< MAIN board top view >

IC802

< MAIN board bottom view >

3-3
RECEIVER BAR ONE POINT REPAIR GUIDE
1-3. NO SOUND

1-3-1. Portable or Optical Function

1-3-1-1. Solution
Replace IC301 or IC304 or Portable/ Optical Jack.

1-3-1-2. How to troubleshoot (Countermeasure)

1) Please check Portable input and Optical Input.
Please check ADC output(Pin9, 10, 13 - I2S signal).
Please check DSP input(Pin80, 94 - S/PDIF signal).
2) If you cannot find input signal, replace Portable/ Optical Jack.
If you cannot find ADC output I2S signal, replace IC304.
If you cannot find DSP input S/PDIF signal, replace IC301.

1-3-1-3. Service hint (Any picture / Remark)

IC304
IC301

< MAIN board top view >

3-4
RECEIVER BAR ONE POINT REPAIR GUIDE
NO SOUND

1-3-2. USB Function

1-3-2-1. Solution
Replace IC301 on MAIN board.

1-3-2-2. How to troubleshoot (Countermeasure)

1) Please check IC301(Pin112, 113) USB data signal.
If you cannot find IC301 USB data signal, replace IC301.

1-3-2-3. Service hint (Any picture / Remark)

IC301

< MAIN board top view >

3-5
RECEIVER BAR ONE POINT REPAIR GUIDE
1-4. NO AUDIO

1-4-1. All function

1-4-1-1. Solution
Replace IC301 or IC701.

1-4-1-2. How to troubleshoot (Countermeasure)

1) Please check IC301(Pin71, 74 and 69, 70) or IC701(Pin5, 6 and 14, 15).
PWM signal output (or input)
2) If you cannot find PWM signal, replace IC301.
If you can find signal PWM, replace IC701.

1-4-1-3. Service hint (Any picture / Remark)

IC301

< MAIN board top view >

IC701

< MAIN board bottom view >

3-6
 ELECTRICAL TROUBLESHOOTING GUIDE
1. RECEIVER BAR TROUBLESHOOTING
1-1. POWER SUPPLY ON SMPS BOARD

No 24 VA

YES

NO
F900 normal? Replace F900 (same fuse).

YES

NO
TH900 normal? Replace TH900.

YES

NO
BD900 normal? Replace BD900.

YES

Is the Vcc NO
(12 V ~ 24 V) supplied to IC920 D921 normal?
Pin4?

YES YES

Power Line of Main PCB is short. Check or replace D921.

3-7
RECEIVER BAR TROUBLESHOOTING
1-2. SYSTEM PART

Power On

YES

“WELCOME” NO IC101 NO
Display on FLD 3 V_MICOM, 3.3 V Check IC801 and SMPS.
OK? OK?

YES

X101 NO
20.000 MHz Replace X100.
OK?

YES

Replace
IC100 UPD78F1165.
MAIN board

3V_MICOM, NO Check D804, IC802

FL(+), FL(-)
OK? & SMPS.

YES

3401_RX, NO
3401_CLK, 3401_STB Check CN303.
OK?

YES

IC301 NO
Data Output to VFD Replace IC301 (FLD Driver).
OK?

YES

Check VFD.
FRONT board

3-8
RECEIVER BAR TROUBLESHOOTING
1-3. NO AUDIO OUTPUT

BD/ CD/ DVD disc or USB play

YES

IC301 NO
Pin112, 113 USB_IN signal Check JK304 or replace.
OK?

YES

IC301 NO
Pin69,70, 71, 74 PWM Signal Check IC301 or replace.
OK?

YES

Check AMP IC output stage

and speaker terminal.

Portable function

YES

IC304 NO
Pin1, 2 PTB input signal Check JK303.
OK?

YES

IC304 NO
Pin 9,10,13 I2S output signal Check IC304.
OK?

YES

Check AMP IC output stage

and speaker terminal.

3-9
RECEIVER BAR TROUBLESHOOTING

Optical function

YES

IC301 NO
Pin35, 94 OPT_IN signal Check JK301, JK302 or replace.
OK?

YES

IC301 NO
Pin69, 70, 71, 74 PWM signal Check IC301 or replace.
OK?

YES

Check AMP IC output stage

and speaker terminal.

3-10
 WAVEFORMS OF MAJOR CHECK POINT
1. SYSTEM PART-1 (X-TAL)

FIG 1-1

MICOM(IC100) - R5F100GEAFB

FIG 1-2

DSP(IC301) – ES8690

3-11
2. SYSTEM PART-2 (I2S SIGNAL)

FIG 2-1

DSP(IC301) – ES8690

3-12
5

FIG 2-2

DSP(IC301) – ES8690

3-13
MEMO

3-14
WIRING DIAGRAMS
1. RECEIVER BAR WIRING DIAGRAM

86%

)5217728&+3&%

3))&

&1 237

237
6036 &1 2$VQ$
(GOCNG
0$,13&%
2$VQ$
31 &1 37%
/CNG
&1 &1

63./63.5 

3))& 3))&

9KTGNGUU
$6/QFWNG
/QFWNG

3-15 3-16
2. WIRELESS SUBWOOFER WIRING DIAGRAM

24'5'6

9%0

20
9%0 952-

9KTGNGUU5WD9QQHGT
#/22%$
5/25 9%0
2.'&

9%0 9KTGNGUU
%0 9%0
/QFWNG
2+0 2
9KTGNGUU
((%

2*CTPGUU5KPING

3-17 3-18
BLOCK DIAGRAMS
1. RECEIVER BAR BLOCK DIAGRAMS
1-1. OVERALL BLOCK DIAGRAM

8(&&TKXGT
/% 8(&
+%
/+%1/
'241/ 4.) +44'%'+8'4

617%*59
%14'4+8'4
(41062#46

5'4+#.
5&4#/
(.#5*

/

/ /#+02#46

$6/QFWNG '5%5% 29/ /&+

#/2+%
7#46 l•šŒ”‰“ŒGpp (4106 6#5.#
5&+
2146#$.' %*#&%

2%/ #&%+0126+0
#PCNQI &5229/
75$$6 +5
EJ
75$ 9KTGNGUU/QFWNG
9KTGNGUU6:
59

52&+(

126+%#. 126+%#.

28&&
8
57$911('4
9KTGNGUU
5/25 /QFWNG #/2+% $&7,9(68%
6#5.# :22)(5
4:

3-19 3-20
RECEIVER BAR BLOCK DIAGRAMS
1-2. POWER BLOCK DIAGRAM

8 8# 8# /+%1/

4.)

8-- 8(&&4+8'4
617%*
/%
(.
8 8(&
5VCPFD[.'&
(. 
8

O#
8 8
75$A8
#< ./#&, 75$,CEM

8
9.A8
8A)8&&
8 #&%
#/2 $6/1&7.'
2%/
6#5.#

9:%* 8 8

O#
#<
8
O#

8 8 &52 5&4#/ 5(.#5*

./#&, '/65# /:.'
O# '5%5%
/ /

O#

3-21 3-22
2. WIRELESS SUBWOOFER BLOCK DIAGRAM

57$911('4#/2

28&&
8 8# 9KTGNGUU/QFWNG
9KTGNGUU4: 5'4+#.
#<
&9#/ (.#5*
/7

8# 28&&
./& 8

8A29/

25 29/
#/2+%
w~tGpj 6#5.# 6XEZRRIHU
59

8

28&&
8

5/25

3-23 3-24
CIRCUIT DIAGRAMS
1. RECEIVER BAR CIRCUIT DIAGRAMS
1-1. SMPS CIRCUIT DIAGRAM IMPORTANT SAFETY NOTICE SPECIAL COMPONENTS ARE SHADED ON THE NOTE :
SCHEMATIC FOR EASY IDENTIFICATION. 1. Shaded( ) parts are critical for safety. Replace only
WHEN SERVICING THIS CHASSIS, UNDER NO THIS CIRCUIT DIAGRAM MAY OCCASIONALLY with specified part number.
CIRCUMSTANCES SHOULD THE ORIGINAL DESIGN DIFFER FROM THE ACTUAL CIRCUIT USED. THIS 2. Voltages are DC-measured with a digital voltmeter
BE MODIFIED OR ALTERED WITH OUT PERMISSION WAY, IMPLEMENTATION OF THE LATEST SAFETY during Play mode.
FROM THE LG CORPORATION. ALL COMPONENTS AND PERFORMANCE IMPROVEMENT CHANGES
12 SHOULD BE REPLACED ONLY WITH TYPES INTO THE SET IS NOT DELAYED UNTIL THE NEW
IDENTICAL TO THOSE IN THE ORIGINAL CIRCUIT. SERVICE LITERATURE IS PRINTED.

11

10

CAUTION:
Danger if fuse is incorrectly replaced.
Replace only with the type identical to fuse rating
and(or) model name described in main label. Warning
1 Parts that are shaded are critical with
respect to risk of fire or electrical shock. SMPS(MAIN)
EAX64990001_3.1.3_SMPS_SD
2012.12.20
A B C D E F G H I J K L M N O P Q R S T

3-25 3-26
RECEIVER BAR CIRCUIT DIAGRAMS
1-2. MAIN-MICOM CIRCUIT DIAGRAM

12

11

10

1
MICOM
: WAVEFORM NUMBER
EAX65067301_4.1.3_MAIN_SD_1
2012.12.20

A B C D E F G H I J K L M N O P Q R S T

3-27 3-28
RECEIVER BAR CIRCUIT DIAGRAMS
1-3. MAIN-DSP CIRCUIT DIAGRAM

12

11

6
10

5 3
8

1
DSP
: WAVEFORM NUMBER EAX65067301_4.1.3_MAIN_SD_2
2012.12.20

A B C D E F G H I J K L M N O P Q R S T

3-29 3-30
RECEIVER BAR CIRCUIT DIAGRAMS
1-4. MAIN-AMP CIRCUIT DIAGRAM

12

11

10

1
AMP
EAX65067301_4.1.3_MAIN_SD_3
2012.12.20
A B C D E F G H I J K L M N O P Q R S T

3-31 3-32
RECEIVER BAR CIRCUIT DIAGRAMS
1-5. MAIN-POWER CIRCUIT DIAGRAM

12

11

10

1
POWER
EAX65067301_4.1.3_MAIN_SD_4
2012.12.20
A B C D E F G H I J K L M N O P Q R S T

3-33 3-34
RECEIVER BAR CIRCUIT DIAGRAMS
1-6. FRONT CIRCUIT DIAGRAM

12

11

10

1
FRONT
EAX65030201_6.1.4_FRONT_SD
2012.12.20
A B C D E F G H I J K L M N O P Q R S T

3-35 3-36
CIRCUIT VOLTAGE CHART
1. ICs
LOCATION ENG. REAL LOCATION ENG. REAL
DESCRIPTION SPECIFICATION DIVISION PIN NO. SPEC. DESCRIPTION SPECIFICATION DIVISION PIN NO. SPEC.
NO. VOLTAGE VOLTAGE NO. VOLTAGE VOLTAGE
R5F100GEAFB 0.5 VCC_12V 2 PIN -0.3~13V 12V 12.290
to 6.5 170mA 20MHz IC,
IC, TAS5612LADDVR -0.3 ~ GVDD1 1,22 -0.3~13V 12V 12.290
IC100 4KBYTE FLASH MEMO- 3V_MICOM 48 PIN 1.8~5.5V 3.30 3.316 IC701 Audio
Microcontrollers 13.2 10.8 ~ 13.2
RY 64KBYTE LQFP TR Amplifier 29,30,31,
PVDD -0.3~50V 18V 12.290
48P - RENESAS 36,37,38
M24C16-RMN6TP TPS54231D DCDC_24V 2 PIN 3.5~28V 24.50 24.300
16KBIT 2KX8BIT IC, 3.5TO28V ADJ 1.2W
IC, 1.8VTO5.5V 4mSEC IC801 DC,DC SOIC R/TP 8P -
IC101 3V_MICOM 8 PIN 1.8~5.5V 3.30 3.316 Converter TEXAS INSTRUMENTS VCC_5VA 1 PIN 3.5~28V 3.30 3.314
EEPROM SO-8 R/TP 8P - SGS-
THOMSON MICRO- INCO.
ELECTRONICS. TPS54331D 4.5VTO28V DCDC_24V 2 PIN 4.5~28V 24.50 24.300
IC,
MX25L2006EM1I-12- ADJ 1.33W SOIC R/TP
IC802 DC,DC
G(TR) 2MBIT 4KBy- 8P - TEXAS INSTRU- VCC_12V 1 PIN 4.5~28V 12.00 12.220
Converter
IC, tex64KByte 2.7VTO3.6V MENTS INCO.
IC102 NOR Flash 12NSEC UNIFORM VCC 8 PIN 2.7V~3.6V 3.30 3.288 IC, 3V3 2 PIN 2.25~16V 3.30 3.288
Memory SECTOR SOP TR 8P LM37102D 2.25V TO
IC805 LDO Voltage
- MACRONIX INTERNA- 16V VDD135 3 PIN 2.25~16V 1.35 1.345
Regulator
TIONAL CO., LTD.
IC, VCC_5V.6V 2 PIN 2.25~16V 5.70 5.800
VCC33_USB 111 PIN 3.3V ±5% 3.30 3.286 LM37102D 2.25V TO
IC806 LDO Voltage
16V USB_5V 3 PIN 2.25~16V 5.00 5.200
VD33VDAC 110 PIN 3.3V ±5% 3.30 3.286 Regulator
VD- PS9854 [2.97V TO 3.63V
104 PIN 1.35V ±5% 1.35 1.345 IC,
D135AADC 0W QFN TP 68P - PUL- 16,25,30,33,
WIC601 Sound/Audio 3.3V_PWM 0 ~ 4.6V 3.30 3.360
SUS TECHNOLOGIES 37,42,50 PIN
VC33AADC 97 PIN 3.3V ±5% 3.30 3.286 Processor
INC.
IC, VD33PLL 95 PIN 3.3V ±5% 3.30 3.286
IC301 ES8690 II+ IC,
MPEG 29,30,31,
VD33ADAC 73, 82 PIN 3.3V ±5% 3.30 3.286 WIC602 Audio TAS5624LA PVDD -0.3~50V 33.00 33.300
36,37,38
Amplifier
12, 23, 48,
VDD135 58, 90, 1.35V ±5% 1.35 1.345 SI-8008TMX-TL 4.5V TO
IC,
114,127 PIN 40V ADJ 1.06W DPAK
WIC606 DC,DC PVDD 1 PIN 0 ~ 43V 33.00 33.300
R/TP 5P - SANKEN
14, 28, 45, Converter
ELECTRIC CO.,LTD.
VDD33 64, 93, 115 3.3V ±5% 3.30 3.286
PIN
W9864G6JH-6 64MBIT
4M X 16BIT 3.3VTO3.6V 1, 3, 9, 14,
IC,
IC302 166Mhz 7ns TSOP II TR VDD33 27, 43, 49 3V~3.6V 3.30 3.284
SDRAM
54P - WINBOND ELEC- PIN
TRONICS CORP.
IC, W25Q16BVSSIG(TRAY)
IC303 Serial Flash 16MBIT 16M X 1bit VDD33 8 PIN 3.3V 3.30 3.285
Memory 2.7VTO3.6V
PCM1808 AVCC_5V 3 PIN 0~6.5V 5.00 5.220
IC, 3.3V 48KHZ 24BIT 6SPS
IC304 A/D 81W TSSOP P/TR 14P -
Converter TEXAS INSTRUMENTS VCC_3V3 4 PIN 0~4.0V 3.30 3.330
INCO.
MC3401 3 TO 5.5V 0 TO
IC,
-33V 200mW LQFP TR
IC501 Display 3V_MICOM 44 PIN 0.3 ~ +7.0 3.30 3.280
44P - - ABOV SEMICON-
Driver
DUCTOR CO. LTD
IC,
Capacitive
IC502 3V_MICOM 24 PIN 1.71 ~ 5.5V 3.30 3.280
Touch TOUCHCORE380 8-BIT
Sensor

3-37 3-38
2. COILS 3. CAPACITORS
LOCATION NO. DESCRIPTION Before After Current Difference Vol. LOCATION NO. DESCRIPTION SPECIFICATION VOLTAGE
L101 Filter,Bead UBW2012-301 300OHM 2A 3.339 3.339 0.011 0 CA201 Capacitor,AL,Chip 22uF 20% 16V 3.291
L102 Filter,Bead UBW2012-301 300OHM 2A 18.17 18.17 0.061 0 CA301 Capacitor,AL,Chip 33uF 20% 25V 5.01
L301 Filter,Bead UBW2012-301 300OHM 2A 3.328 3.328 0.011 0 CA302 Capacitor,AL,Chip 33uF 20% 25V 3.298
L304 Filter,Bead UBW2012-301 300OHM 2A Signal Signal CA602 Capacitor,AL,Chip 100uF 20% 16V 12.19
L305 Filter,Bead UBW2012-301 300OHM 2A Signal Signal CA603 Capacitor,AL,Chip 47uF 20% 50V 17.55
L306 Filter,Bead UBW2012-301 300OHM 2A 5.02 5.02 0.017 0 CA604 Capacitor,AL,Chip 47uF 20% 50V 18.14
L307 Filter,Bead UBW2012-301 300OHM 2A USB GND USB GND CA614 Capacitor,AL,Chip 100uF 20% 16V 3.281
L308 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.323 0.011 0 CA615 Capacitor,AL,Chip 100uF 20% 16V 1.357
L309 Filter,Bead UBW2012-301 300OHM 2A 3.321 3.321 0.011 0 CA616 Capacitor,AL,Chip 47uF 20% 50V 18.15
L310 Filter,Bead UBW2012-301 300OHM 2A 3.299 3.299 0.011 0 CA617 Capacitor,AL,Chip 100uF 20% 16V 5.02
L311 Filter,Bead UBW2012-301 300OHM 2A 5.01 5.01 0.017 0 CA702 Capacitor,AL,Chip 330uF 20% 35V 18.16
L501 Filter,Bead UBW2012-301 300OHM 2A 3.321 3.321 0.011 0 CA703 Capacitor,AL,Chip 330uF 20% 35V 18.16
L605 Filter,Bead UBW2012-301 300OHM 2A 18.17 18.17 0.061 0
L606 Filter,Bead CIS21J121 120ohm, 5A 18.18 18.18 0.152 0
L609 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.321 0.011 0.002
4. CONNECTORS
L610 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.323 0.011 0 LOCATION NO. PIN NUMBER SPEC. VOLTAGE
L611 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.322 0.011 0.001 1 DGND 0
L612 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.321 0.011 0.002 5 DGND 0
L613 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.322 0.011 0.001 6 VCC_5V 5.02
L614 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.322 0.011 0.001 CN101 7 BL_12V 12.18
L615 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.307 0.011 0.016 9 3V_MICOM 3.329
L616 Filter,Bead UBW2012-301 300OHM 2A 3.323 3.323 0.011 0 10 3V_MICOM 3.329
L617 Filter,Bead UBW2012-301 300OHM 2A 5.02 5.02 0.017 0 13 DGND 0
L618 Filter,Bead UBW2012-301 300OHM 2A 5.42 5.41 0.018 0.01 1 GND 0
L619 Filter,Bead UBW2012-301 300OHM 2A 3.298 3.281 0.011 0.017 CN105 3 GND 0
L620 Filter,Bead UBW2012-301 300OHM 2A 1.353 1.336 0.005 0.017 4 3V_MICOM 3.326
L621 Filter,Bead UBW2012-301 300OHM 2A 1.353 1.353 0.005 0 1 DGND 0
L622 Filter,Bead UBW2012-301 300OHM 2A 12.19 12.18 0.041 0.01 5 DGND 0
L624 Filter,Bead UBW2012-301 300OHM 2A 5.02 5.02 0.017 0 6 VCC_5V 5.02
L625 Filter,Bead UBW2012-301 300OHM 2A 3.335 3.335 0.011 0 CN201 7 BL_12V 12.18
L626 Filter,Bead UBW2012-301 300OHM 2A 5.02 5.02 0.017 0 9 3V_MICOM 3.329
L629 Filter,Bead UBW2012-301 300OHM 2A 3.97 3.96 0.013 0.01 10 3V_MICOM 3.329
L631 Filter,Bead UBW2012-301 300OHM 2A 5.18 5.18 0.017 0 13 DGND 0
L632 Filter,Bead UBW2012-301 300OHM 2A 18.18 18.18 0.061 0 1 GND 0
L701 Filter,Bead UBW2012-301 300OHM 2A 12.07 12.07 0.040 0 CN501 3 GND 0
L702 Filter,Bead UBW2012-301 300OHM 2A 12.07 12.07 0.040 0 4 3V_MICOM 3.326

3-39 3-40
PRINTED CIRCUIT BOARD DIAGRAMS
1. RECEIVER BAR PRINTED CIRCUIT BOARD DIAGRAMS
1-1. SMPS P. C. BOARD
(TOP VIEW)

(BOTTOM VIEW)
NOTE) Warning
Parts that are critical with respect to risk
of fire or electrical shock.

3-41 3-42
RECEIVER BAR PRINTED CIRCUIT BOARD DIAGRAMS
1-2. MAIN P. C. BOARD
(TOP VIEW)

(BOTTOM VIEW)

3-43 3-44
RECEIVER BAR PRINTED CIRCUIT BOARD DIAGRAMS
1-3. FRONT P. C. BOARD
(TOP VIEW) (BOTTOM VIEW)

3-45 3-46